Related
Just a very quick review of my Easecase E5 which arrived about a week ago.
You can see pictures of it by search eBay for "Easecase E5 galaxy note" (without quotes), there's one here : http://www.ebay.co.uk/itm/E5-EASECA..._MobilePhonesCasesPouches&hash=item5ae4059699
(I did get a bit of a shock when I saw that - that is my actual one - with my name on it, I was just searching for one at random)
Delivery time:
As mentioned in other parts of this forum, delivery times for Easecase are pretty woeful. I ordered on the 25th of November and, it arrived here a few days over a month later in Sweden. The problem seems to be largely that they ship via China Post which is quit slow - they dispatched it (with trackable* shipping) within about a week. I bought it through eBay, so I am not sure if they have another outlet, and, they make it very clear on their eBay items that they will take a looong time to ship, so, I can't take any points off them there.
Build quality:
It is beautifully put together. There's a slot running down the inner spine for the stylus, and my name is embossed on the front. I would characterise it as high quality.
Outside:
I opted for the magnetic clasp. It isn't a very strong magnet, but does the job.
Apart from the clasp, there's just the embossing on the outside, and, a neat seam around the edge.
Inside:
There are 2 bill pockets inside, both of which are *very* deep. They're about as deep as the note is high.
When it is fully opened, there are 5 credit card pockets on the left. Note that these seem to be individual pockets, separated from each other internally. Cards fit vertically into these pockets. The front of the pockets stretches a bit over 2 thirds of the way from the far left of the case to the spine. Behind the pockets is a sleeve about 1/3 wider than the short side of a credit card where you could fold bank notes* (remember this, I'll come back to it.
As I said, along the inner spine is slot for the stylus.
On the right is where the not goes. It slots in (quite snugly) from the top. The top is open, so you can get to the headphone port. There's a hole in the left for the volume control, a hole in the right for the power button, and, a hole in the bottom for access to the USB port.
Looking at the front, the home and hardware buttons are all accessible as part of the screen area. They've also neatly cut out around the top speaker and, the front camera.
Protection:
Very good. If the magnetic clasp doesn't come undone during a fall, then, it'd be very hard to break the screen. It is nice thick leather, and you might even be able to drop a brick on it when closed without breaking the screen.
It still won't help you if you drop it in the toilet as some poor chap here has apparently done.
Usage:
It is very bulky. Like one of those filofax jobs people used to (still?) have.
I'm used to big gadgets, so I cope, but you wouldn't get it into tight jeans pockets. I do squeeze it, with some discomfort into my front trousers pocket.
You don't want to talk on the phone with the cover on for more than brief calls, you look like an idiot. Most of the time I pull it out of the cover for calls, or, use a bluetooth headset.
Using the rear camera requires removing from the cover.
General browsing/emailing etc is fine with the cover on.
Fortunately removing the phone is a fairly quick procedure, as is putting it back it. I imagine it'll get easier still as the leather stretches a touch.
One annoyance is, as the leather reaches right to the top of the touch screen, if the phone slips up slightly, it can be difficult or impossible to pull down the notifications bar. When in landscape, this isn't an issue as the phone can't move left/right in the case.
Summary/thoughts:
I wish I'd bought the one without the bank note pockets. That'd reduce the bulk considerably and you could still stick notes behind your cards (see * above). You can also use the rear facing camera with the non-bank note version (E4).
On balance, I am pleased I bought it though, it is of high quality and, it is great having your phone and wallet all in the one thing - it also means you can ring your wallet to find it when you are in a hurry to head to work
If anyone has any questions, I'd be happy to answer them.
My recommendation for anyone thinking of getting one of these is to get the E4 and not this.
They don't seem to have any E4's on eBay at the moment for the note, but I am sure I have seen one there. Here's one for the Desire HD - I am sure it gets the point across.
http://www.ebay.co.uk/itm/E4-EASECA...sesPouches&hash=item5647be7cbf#ht_5657wt_1016
Cheers,
Kent
kentmartin said:
You don't want to talk on the phone with the cover on for more than brief calls, you look like an idiot. Most of the time I pull it out of the cover for calls, or, use a bluetooth headset.
One annoyance is, as the leather reaches right to the top of the touch screen, if the phone slips up slightly, it can be difficult or impossible to pull down the notifications bar. When in landscape, this isn't an issue as the phone can't move left/right in the case.
Click to expand...
Click to collapse
Two quick thoughts:
1) When calling, can't you fold the case cover back 180 degrees?
2) Some launchers (adwlauncher does this) allow to swipe down anywhere to lower the notification bar, so you don't need to touch the very top.
- Frank
ChodTheWacko said:
Two quick thoughts:
1) When calling, can't you fold the case cover back 180 degrees?
Click to expand...
Click to collapse
No, the banknotes pockets kind of open so it gets more bulky and wants to spring back to about 180 degrees (where 0 is closed, 180 is wide open and 360 is the position you suggest), but I suspect you could with the E4 model.
2) Some launchers (adwlauncher does this) allow to swipe down anywhere to lower the notification bar, so you don't need to touch the very top.
Click to expand...
Click to collapse
Yes - I read about that setting a while back, but have never used it, thanks for reminding me - it is now enabled for the swipe down gesture (hide dock was annoying me anyway).
Hi, thanks for the review, i've been stuck deciding between the E5 and the E4, due to the E5 having the bill slot, which i would think is really good compared to folding the bills under the cards.
Can you take a picture of the case when it's fully loaded, both open and closed?
e.g. all card slots used, and the bills folded and slotted under the cards
That would probably help sway my decision, if that slot + cards do not bulk up the entire wallet.
More info // pics in my thread. http://forum.xda-developers.com/showthread.php?t=1419678
I love those case, but it's sucks when they cost so much!
It's should be 10$ max.
peanuts and monkeys
i hope to order this case by the end of this month, i've emailed them some questions on customisation, hopefully it's permitted, then can go forward with this.
the E5 with wallet style slot is definitely too bulky. I bought one for my Desire HD with modified size to fit the DHD with Otterbox. After receiving it, tested once with DHD and sit in my drawer collecting dust ever since.
EvoFighter said:
the E5 with wallet style slot is definitely too bulky. I bought one for my Desire HD with modified size to fit the DHD with Otterbox. After receiving it, tested once with DHD and sit in my drawer collecting dust ever since.
Click to expand...
Click to collapse
Ya know I thought the same thing at first, but I just got a pack of 3 extra batteries and I find I can put two of em in the wallet and also a cleaning cloth and everything fits great.
In terms of customizations I wonder if a small bit for some change could be added.
Its beautiful.
Easecase E5 looks good.
This is a genuine leather case, and very good quality construction. They also responded well to my customization request (I wanted a 65mm horizontal belt loop added to mine).
Only $10 max is out of the question. Worth 3 to 4 times that much. It includes branding of your own name as well. It's a very classy leather case/wallet.
Could you please share a photo were the Note is next to the case just to compare the size of the case?
Hey great review. I really love the customization of these cases and I recently bought a galaxy note us version from ATT so ive been doing some research for a quality wallet type case for my note (will arrive monday) I was just wondering, would this case or the E4 case which is what ill probably get be fine for the american ATT version. Im pretty sure the dimensions are about the same but im not so sure about the button placements or the charger placements.
The only thing I dont like is the shipping time but not much I can do about it but this case seems to be the best so far that ive found besides the vintage leather case but those dont come in black and have magnetic strips.
Any reply would be appreciated.
So just to recap - will my US ATT galaxy Note i717 be a good match with this case?
dreamstealer2045 said:
Hey great review. I really love the customization of these cases and I recently bought a galaxy note us version from ATT so ive been doing some research for a quality wallet type case for my note (will arrive monday) I was just wondering, would this case or the E4 case which is what ill probably get be fine for the american ATT version. Im pretty sure the dimensions are about the same but im not so sure about the button placements or the charger placements.
The only thing I dont like is the shipping time but not much I can do about it but this case seems to be the best so far that ive found besides the vintage leather case but those dont come in black and have magnetic strips.
Any reply would be appreciated.
So just to recap - will my US ATT galaxy Note i717 be a good match with this case?
Click to expand...
Click to collapse
When I dealt with them, I found them quite responsive, I suggest asking them if it'll fit the i717 - odds on if it doesn't they'll have one that does even if they haven't advertised it yet.
Although I haven't seen it, I'd definitely recommend the E4 over the E5 - I find I don't really need the slots for notes (you can slip folded notes in the bit behind where credit cards go anyway) and, it the banknote pockets block the camera (by necessity) which drives me a bit mad.
The Sprint S3 is my first smartphone and this forum has been AMAZINGLY helpful to me and I thank everyone here greatly. Sadly at this point I dont really have anything useful to give back, however I do get comments and questions on my ghetto battery modding by people at school all the time, so maybe a few of you will get a chuckle out of it too:
View attachment 1512485
View attachment 1512486
View attachment 1512487
View attachment 1512488
I bought 2 extended batteries, a 4800mAh no name off ebay and a 4500mAh onite off amazon, then I stripped off their casings and seperated the cells then I stripped the cover off my stock battery and carefully lined up everything and glued all 5 cells together with arctic silver thermal adhesive. After that I carefully wired them all together in parallel and cut a hole in my otterbox so that they all stick out the back. I figure I now have between 10500mAh and 11400mAh.
Ghetto eh? But it works great, it charges just like normal and while I can kill it by gaming all day, it lasts about 3-5 days under normal usage for me depending on how I have my settings. An unexpected benifit that I discovered completely by accident is that if you drop it from about 3.5-4 feet up it seems to always land flat on the battery (I tested this by standing on my bed doing drop tests).
If I had been very careful I could have even kept the NFC antenna on the battery doing this, but I didnt know to watch out for it, so I accidently destroyed it.
joelespinoza said:
The Sprint S3 is my first smartphone and this forum has been AMAZINGLY helpful to me and I thank everyone here greatly. Sadly at this point I dont really have anything useful to give back, however I do get comments and questions on my ghetto battery modding by people at school all the time, so maybe a few of you will get a chuckle out of it too:
Well that sucks.... I cant post pictures of it.... Just google joelespinoza photobucket they should be the top pictures in my only album.
I bought 2 extended batteries, a 4800mAh no name off ebay and a 4500mAh onite off amazon, then I stripped off their casings and seperated the cells then I stripped the cover off my stock battery and carefully lined up everything and glued all 5 cells together with arctic silver thermal adhesive. After that I carefully wired them all together in parallel and cut a hole in my otterbox so that they all stick out the back. I figure I now have between 10500mAh and 11400mAh.
Ghetto eh? But it works great, it charges just like normal and while I can kill it by gaming all day, it lasts about 3-5 days under normal usage for me depending on how I have my settings. An unexpected benifit that I discovered completely by accident is that if you drop it from about 3.5-4 feet up it seems to always land flat on the battery (I tested this by standing on my bed doing drop tests).
If I had been very careful I could have even kept the NFC antenna on the battery doing this, but I didnt know to watch out for it, so I accidently destroyed it.
Click to expand...
Click to collapse
Great story. You get your first thanks from me. I do crazy modding like this sometimes and love it if some else appreciates the ghetto inventiveness. Love the drop testing bit. Absolutely entertaining....and actually...the mod...for you...is very useful!
themadproducer said:
Great story. You get your first thanks from me. I do crazy modding like this sometimes and love it if some else appreciates the ghetto inventiveness. Love the drop testing bit. Absolutely entertaining....and actually...the mod...for you...is very useful!
Click to expand...
Click to collapse
Thanks man! I appreciate it. And my wife has a normal S3... Honestly I like the way mine feels MUCH better, its just way easier to hold onto and easier to use one handed without it slipping around. The fact that I could use it to jump start my Honda in a pinch is a nice bonus too!
joelespinoza said:
Thanks man! I appreciate it. And my wife has a normal S3... Honestly I like the way mine feels MUCH better, its just way easier to hold onto and easier to use one handed without it slipping around. The fact that I could use it to jump start my Honda in a pinch is a nice bonus too!
Click to expand...
Click to collapse
Ironically, my Honda battery is suffering during this colder season and could use such a boost! LOL
Honestly, I can't see how anyone could actually use the S3 without a case. I have never held such a slippery and uncomfortable device...begging to fly out of my hand. Too thin. But there are so many case options out there that compliment it. Love it. :good:
On the topic of "entertainment", here is a video for a new Griffen Survivor case that gives your BED DROP tests a run for the money...
all well and good but isnt this extremely dangerous to carry around like that?
ddurandSGS3 said:
all well and good but isnt this extremely dangerous to carry around like that?
Click to expand...
Click to collapse
Dangerous? is it dangerous to carry a 9 volt battery? Fully charged this is around 4 volts, why would it be dangerous?
When that hack job goes into thermal runaway, it will be like a cutting torch in your pocket and you'll have a new asshole out the side of your waist. What a mess.
MCL1981 said:
When that hack job goes into thermal runaway, it will be like a cutting torch in your pocket and you'll have a new asshole out the side of your waist. What a mess.
Click to expand...
Click to collapse
Very unlikely, I wear carpenter jeans and and always use the leg pocket for my phone and nothing else goes in there, so there is almost no chance of it shorting out against anything. This phone has had this battery since about 3 weeks after Sprint released the S3s and it has never been an issue, and I recently redid the connections and switched from gorilla glue to thermal adhesive.
Not only that but if it did start heating up, there is nothing holding the battery in there but friction. Pulling the battery out takes me all of 1 second.
But worse case scenario if you wanted to do it and you were worried about it, just pot the side with the connections.
Hahaha this is great, love the idea!
Sent from my SGH-T999 using xda premium
i carry uncovered batteries (AA) like that for another device and shortly after use if they come in contact with anything metal they can combust, and at the very least burn a hole rught through your pants and severely burn your leg.
just asking. dont know naythign about batteries but i had one close call with the AA batteries.
ddurandSGS3 said:
i carry uncovered batteries (AA) like that for another device and shortly after use if they come in contact with anything metal they can combust, and at the very least burn a hole rught through your pants and severely burn your leg.
just asking. dont know naythign about batteries but i had one close call with the AA batteries.
Click to expand...
Click to collapse
I work in IT and keep my pockets very organized, if I was tossing this phone into a purse or pocket with a bunch of loose change or other metal objects I would have it better insulated. I will probably do so anyway at some point but right now it is not an issue.
As a side point I seriously doubt anything but shorting out could possibly cause any kind of "thermal runaway" with this setup. The battery has 5 times the mass and better airflow then stock and the phone can only draw the same power. I do still get a warm screen with this setup (how the CPU/GPU dissipates heat) but the battery never gets much more then body temp, even under the most brutal use for hours at a time.
That's frickin' sweet! Could you make a video of this? Lol. I'd attempt it if I had a video to follow.
Well it was sweet until I saw the pictures.. LOL! Not really something I'd want on the back of my phone.. It's usually function over fashion for me, but in this case I think I'll make an exception. It's not really the fashion thing, it's I think it'd be really awkward to hold.
nh97103 said:
That's frickin' sweet! Could you make a video of this? Lol. I'd attempt it if I had a video to follow.
Well it was sweet until I saw the pictures.. LOL! Not really something I'd want on the back of my phone.. It's usually function over fashion for me, but in this case I think I'll make an exception. It's not really the fashion thing, it's I think it'd be really awkward to hold.
Click to expand...
Click to collapse
Keep in mind I am not trying to convince anyone else to do this, and I have readlly big hands as you can see from the pictures, but I find it much more comfortable to hold and use. 2 handed its only slightly better, but one handed its WAY better... the bottom edge of the battery fits right above my pinky and the weight centered in the back both give a much better feel.... when I hold my girlfriends stock s3 in one hand it feels like its gonna fall straight down out of my hand or fall forewards towards me, that might just be me though.
It also has what I call a manly heft. I don't mind it at all but if you are looking for a sleek featherweight device..... this isn't. But I like it :fingers-crossed:
joelespinoza said:
Keep in mind I am not trying to convince anyone else to do this, and I have readlly big hands as you can see from the pictures, but I find it much more comfortable to hold and use. 2 handed its only slightly better, but one handed its WAY better... the bottom edge of the battery fits right above my pinky and the weight centered in the back both give a much better feel.... when I hold my girlfriends stock s3 in one hand it feels like its gonna fall straight down out of my hand or fall forewards towards me, that might just be me though.
It also has what I call a manly heft. I don't mind it at all but if you are looking for a sleek featherweight device..... this isn't. But I like it :fingers-crossed:
Click to expand...
Click to collapse
Even if it was awkward to hold, the battery life would so be worth it.. Getting the battery life of my old flip phone would be an incredible experience on a smartphone. I don't think I'd ever attempt this, but I'm wondering did just kinda wing it, or did you know what you were doing..?
Be super careful doing this. I know that lithium polymer batteries are really bad news if they are punctured or damaged... I believe this is also the case with the Lithium Ion batteries.. specifically if you inadvertently short them causing heat and internal breakdown.. Have seem my share of laptops that were burned when someone used the wrong laptop power supply (21V instead of 12V for example)
Not saying to not do this sort of mod... just saying to be VERY careful and don't risk your safety or risk burning down your house for the sake of extra battery life.. there are too many USB charging batteries out there to help with battery life extension if you are away from a USB port for too long.
nh97103 said:
Well it was sweet until I saw the pictures.. LOL!
Click to expand...
Click to collapse
Where are the pictures? I would like to see how it looks.
Ninolina said:
Where are the pictures? I would like to see how it looks.
Click to expand...
Click to collapse
I added a couple pics in the first post.
nh97103 said:
I don't think I'd ever attempt this, but I'm wondering did just kinda wing it, or did you know what you were doing..?
Click to expand...
Click to collapse
I have done my fair share of messing with electronics, but im not an electrical engineer or anything... If you are comfortable soldering, its not that big of a deal. The hardest part is attaching the wires to the stock battery, because you have to lift up the small circut board the contact points are attached to, then resolder it back down after you attach wires underneth it. But to be fair you dont need the boards of the other 2 batteries so you can pratice on them. Then you line up all the batteries where you want them and glue them together. After that its all wire routing and ataching negatives to negatives and positives to positives.
It would probably be a good idea to have the main battery completely drained before starting. But having the other 4 with some charge would be fine if you are somewhat careful.
Be sure to pick a very thin wire with a decent casing, some kind of ribbon wire would probably work best I think, however, I just used ethernet wire I had laying around, but some of them had great insulation and some of them the insulation sucked.
If you want to play around with it without jumping in with both feet you can take apart just about any old cell phone battery and see how they are put together, they are all pretty similar. My old verizon LG octane 950mAh battery actually runs my S3 and charges normally in it, it just has to be held in with a piece of tape.
Its like anything really, if you are patient and careful you will get a nice finished product, if you are not......
You need more protection. If anything ever, and yeah, I get it, you never have anything in your pocket, but if anything ever shorts that out, you're ****ed.
The whole "Never have anything in my pocket" argument isn't working for me. You could have it on a desk, bump something into it, and then burn down the building you're in. Just cover it up and it should be fine.
Felnarion said:
You need more protection. If anything ever, and yeah, I get it, you never have anything in your pocket, but if anything ever shorts that out, you're ****ed.
The whole "Never have anything in my pocket" argument isn't working for me. You could have it on a desk, bump something into it, and then burn down the building you're in. Just cover it up and it should be fine.
Click to expand...
Click to collapse
I do agree I should probably slap some insulation on the side... However I think all of you people who are worried about something terrible happening are wildly overestimating the results.... I have shorted out this battery, its not a huge deal. Would it be bad if I purposefully directly shorted it out for a long period of time? Well yea... is it a big deal if it brushes up against something and I immediately pull it away? Has not been a problem so far,,,
This is not a single cell battery, its 5 cells connected by thin copper wire... I have actually used copper wire this thin as a fuse in a pinch, if it gets hot it melts then you are back to a single cell, assuming that the arcing didnt simply melt away the metal shorting out, which usually happens nearly instantly.
I know Lithium ion batteries can be dangerous, I also know how much abuse it usually takes to make them that way. I was around and saw some of these "tests" first hand with Luke:http://www.youtube.com/watch?v=dree...gcnR3aIyzfEYEaOlYsyQe_ANtSuo7U2FsvDnzcBTJK8yE
an s3 commuter with batteries?
who does that?:laugh:
DODOcase has revealed their line of products for the new Nexus 7. For the crowd that desires a more premium offering when it comes to device preservation.
**DODOcase Nexus 7 2013
I like the look of the dodocases, but the least expensive cover (34.95) has a mention that they recommend holding the device in with glue!
The more expensive cases don't seem to have any superior retention strategies.
I'm surprised. When I made a very similar case for my nook color, I spent time figuring out how to fit latches at the lower left and upper righthand sides so the device would stay in place even if the case opened.
The one on the upper right was movable, so I could release the Nook for the (many) times I wanted access to the sdcard slot.
With real tools, I'd have thought Dodo would've been able to do something similar by now that looked better than what I came up with. (Mine was a half a stopcock fastened inside the cover. I took a hacksaw and cut one of the "ears" off the stopcock, then cut the total length of the unit to the right length for my purpose. With that done, the half-eared top can be removed from the butt end, and screwed in in reverse so the wide end is flush with the cover and the remaining ear is able to rotate out to hold the device in, or rotate back to let you remove it from the cover.)
Pad and Quill have a nice computerized lathe as well, and I think their cases are better than the Dodocases. (Dodo benefits from being in San Francisco and able to invite the tech press to visit.)
The P and Q cases now have a kind of retention system in them, nice to see someone at least trying.
http://www.padandquill.com/all-pq-cases.html
Sadly, only available for Apple and Amazon devices at this time.
Hmm, where do you see the suggestion of additional glue? I had the hardcover classic for my original - ended up handing it off as I preferred my Treegloo case (won't be doing that again) - and the adhesive strips were more than strong enough during my use and the use it got from the other party. Never had to seek out additional means of securing the device, and obviously resorting to glue would be a terrible alternative lol
I'm assuming the more traditional bookcase styles still have the same leather inserts they used before to adequately secure your device. I haven't heard any horror stories and, truthfully, while I can't vouch for that specific model, I've heard nothing to suggest they don't hold your device as securely as a Portenzo or Treegloo.
It is too bad that P&Q don't have an offering, but one can hope! Some good alternatives, though, in Portenzo and the aforementioned DODO.
Check ou the "super duper adhesive" section on this listing for the hardcover classic.
http://www.dodocase.com/products/hardcover-classic-for-nexus-7-2
This is the closest thing I see for what you're talking about...?
Industrial-grade adhesive used to secure the Nexus 7 is reusable and residue-free. Wiping the adhesive down with water restores the stickiness.
Click to expand...
Click to collapse
It's a double sided adhesive tape, 3M, that can have the stickiness restored by wiping a damp cloth on it. Should the adhesive even need it. I'm not sure where you're getting the suggestion to use additional glue. Sorry. This is the method of holding the device in this particular case. It may sound kind of odd, but I can attest to the adhesive working as advertised. As for the proper bookcase styles; the leather inset works as advertised, too, to securely hold the device. No further means of retention required.. DODO may not offer the same level of options as Portenzo, but they are quality cases made with quality materials. I can attest to that.
Sent from my Galaxy Nexus
We're talking about the same thing, it's a matter of how you apply the adhesive to the device. I had not realized they were talking about double sided tape.
My point is that I'm disappointed that the high end case makers have done so little about keeping the devices in place. I came up with a latching mechanism that leaves the device free of adhesive. It still works 2+ years in on my GFs case and both my nieces' cases, keeps the device in the case even upside down with the cover open.
I'd rather buy a nice case that can do that than make another myself, but I'm not interested in buying a pretty case that isn't as good as cases I've made, since they came out looking great.
Attached is a pic of my gf's case after 2+ years of daily use, showing the latches and magnetic closure. sleep / wake by cover isn't a feature of the nook tablet but would be trivial to build into one of these as well.
I had a Portenzo case (and ordered a new one). I never had my old N7 fall out. Even when I went to sell it, I had a good time peeling it off my Nexus 7. Does a great job, cleans up with water, and is ready again. I removed mine a few times during the trial run but eventually just left it alone. I didn't have the wood around mine either, so the glue is really good.
Shame these are so expensive. Almost $40 after shipping. I know each one is custom made, but they don't look too complicated. Oh well. Portenzo people are really cool, so I don't mind paying a little extra for some good customer service, good product, and a good laugh (you ever chatted with them?).
roustabout said:
My point is that I'm disappointed that the high end case makers have done so little about keeping the devices in place. I came up with a latching mechanism that leaves the device free of adhesive. It still works 2+ years in on my GFs case and both my nieces' cases, keeps the device in the case even upside down with the cover open.
Click to expand...
Click to collapse
I see, but not sure why you think these cases need any additional means of securing the device. A latching mechanism would certainly not be needed, and would only serve to spoil the appearance of the case. And there is no residue left over on the actual device with the aforementioned models. The adhesive is a curious means of securing the device, and I can understand the skepticism, but it works extremely well in my experience.
@player911 I do agree that even the cheaper models are more expensive than most would want to consider, but such cases are meant for a particular crowd.
Ordered mine with portenzo
Some decent selection.. I have a P and Q with my Ipad and like these better.
http://shop.portenzo.com/new-nexus-7/
Portenzo has some very nice options :thumbup:
Sent from my Nexus 7
mmegalodon said:
I see, but not sure why you think these cases need any additional means of securing the device. A latching mechanism would certainly not be needed, and would only serve to spoil the appearance of the case. And there is no residue left over on the actual device with the aforementioned models. The adhesive is a curious means of securing the device, and I can understand the skepticism, but it works extremely well in my experience.
Click to expand...
Click to collapse
Well, the use of adhesive is (to me) an additional means of securing the device. And I didn't come up with my mechanism for it idly - I repeatedly had the devices fall out while reading, especially in bed.
It is possible to make a latching mechanism that doesn't spoil the look if you have the right tools and time. Two years is more than enough time. One very simple mechanism would be to put one of the wood sides (probably the one normally at the 'top') on a hinge (countersunk underneath) and have it slot into the two sides it abuts with a swiveling peg latch mechanism on either end.
Make all four sides not rectangular but 3/8" at the base and 5/8" across the top and you'd have a natural and simple slide-in, slide-out retention bezel. It would look very, very similar to the current line of products.
And now that I've thought about it, I think I have the parts in the house to make one, and I may do that although I'll probably use jewelry hooks to catch the top beam against the cross beams.
roustabout said:
Well, the use of adhesive is (to me) an additional means of securing the device. And I didn't come up with my mechanism for it idly - I repeatedly had the devices fall out while reading, especially in bed.
Click to expand...
Click to collapse
The adhesive is the only means of securement on this particular model. And this won't be happening, which is why these (all their models, including the likes of Portenzo, Treegloo) cases don't require additional means of retention.
It is possible to make a latching mechanism that doesn't spoil the look if you have the right tools and time... ....It would look very, very similar to the current line of products.
Click to expand...
Click to collapse
I'm all for DIY, so if you can make a case that looks half as good as a DODOcase - or a Portenzo - I would be genuinely interested in seeing it.
Hi all,
I've recently come back into the android fold and I'm currently using the Nexus 6P (fantastic phone btw) and now I'm branching out to other android devices.
I've always wanted a smart watch and I feel now is the time to dive in. After a lot of research that's left me with two options and I'm torn between the Moto 360 (46mm) and the Huawei watch. I've read countless reviews and they both have their pro's and con's, such as cost, display, battery, looks, functionality and I've read into the issues surrounding the charging cradles which only makes my decision more difficult.
I'm all for customization and can spend hours on XDA reading and trying tings regarding my phone and android in general which made me take note of in terms of support and activity the Moto 360 has a lot more attention on XDA, I appreciate that this is most likely due to the Moto 360 being more main stream and has been out for longer, not to mention the V1 lead the charge for android wear but user support is very important to me.
At the moment I'm not sure how I feel about the flat tyre which appears to most of the gripes for the 360 however on investigation several watches faces appear to have overcome this issue to some extent and many users after some time appear to have forgotten all about it, plus it does serve some practicality with the ambient display so it's not all bad.
Any thoughts? Pro's and con's? Have you owned both watches or come from the 360?
Hua Wei watch has sapphire crystal. Enough said.
Sent from my LG-H815 using Tapatalk
Sounds like you want moto 360. Both are great. Huawei watch much more nicer and more classy expensive looking. Moto has it in bigger size as well, so if u like bigger watch faces then you need moto.
I personally love my black Huawei. It is worth every penny. I could care less about customization and user support forums. I buy technology to help me save time in my busy life. I don't have time nor the interest to be reinventing android wear on my watch.
Sapphire
sinple said:
Hua Wei watch has sapphire crystal. Enough said.
Sent from my LG-H815 using Tapatalk
Click to expand...
Click to collapse
Bingo! Can't say enough about the durability of this watch also. Only wish it were more water proof.
---------- Post added at 06:35 AM ---------- Previous post was at 06:30 AM ----------
I don't believe the moto has a speaker either.....does it? Plus have you seen the display on the moto in ambient mode? Holy s...! It's completely pixilated. When I'm inside the house,office,mall, anywhere other than outside,the huawei ambient mode is easily visible, and completely crystal clear. No pixelation. The watches are in these ambient modes most of the time,especially if you have tilt to wake off like me. Please watch videos on you tube comparing this ambient mode with the moto.....its so nasty and ghetto looking.
My decision came down to the fact that the Moto 360 had a flat tire. I wanted a fully circular watch. I think the biggest downside to the Huawei Watch is the horrible charging mechanism. It's a pain to work with especially when I have to quickly charge my watch using a portable charger and throw it in my bag.
Hi all,
After much consideration I ended up ordering the 46mm Moto 360. It basically came down to price at the end of the day. The Huawei watch is £329 with the standard leather strap, I was able to order via a discount code a 46mm Moto 360 with a 22mm metal band and a micro Knurl Bezel for £280. Both are added extras above the standard Moto 360.
I may come back to the Huawei watch as I'm still concerned about the flat tyre and pixel density, however given the extras, screen size and the cost I felt it was too good of an option to let go.
Thanks for all the advice above!
redeuxx said:
My decision came down to the fact that the Moto 360 had a flat tire. I wanted a fully circular watch. I think the biggest downside to the Huawei Watch is the horrible charging mechanism. It's a pain to work with especially when I have to quickly charge my watch using a portable charger and throw it in my bag.
Click to expand...
Click to collapse
I am surprised about the dislikes of the HW charging mechanism. I own both HW and Gear S2 Classic. I see no advantage or disadvantage of either charging means. I hold the HW just above the dock and it snaps in place - nothing difficult. Even when using a portable charger in my bag, while hardly ever needed though, the HW stays connected to the dock. Same with the Gear S2. It is also easy to put gear on dock as it snaps on, but I am not especially pleased that there are no connector pins. I just don't care....
I haven't checked yet if Gear S2 remains docked in my bag. I think the HW is better locked though.
tinker_tf said:
Hi all,
After much consideration I ended up ordering the 46mm Moto 360. It basically came down to price at the end of the day. The Huawei watch is £329 with the standard leather strap, I was able to order via a discount code a 46mm Moto 360 with a 22mm metal band and a micro Knurl Bezel for £280. Both are added extras above the standard Moto 360.
I may come back to the Huawei watch as I'm still concerned about the flat tyre and pixel density, however given the extras, screen size and the cost I felt it was too good of an option to let go.
Thanks for all the advice above!
Click to expand...
Click to collapse
Actually I only paid £289 on Amazon for the black leather strap. I then bought a brown leather, a stainless steel band and mesh band on Amazon, pretty much identical to the originals and spent about £320 in total. Not bad for the watch and 4 straps!
Sent from my Nexus 6P using Tapatalk
I got a pretty good price on my Huawei Watch a week ago. I live in EU but ordered from USA. Even with import tax and 2 day delivery it was still cheaper than anything in the rest of the world (and I checked). It ended up costing $427/£290/€390.
I ordered silver with leather band which I am not a fan of but mesh is already on the way. Hopefully it doesn't look too feminine.
I did get stupid USA charger which is useless in Sweden, but I have a converter at home (and it costs anyway like $5) so it's all good.
This is the watch I bought, although mine was cheaper at time. $310 or so, probably some Christmas price cut:
http://www.amazon.com/gp/product/B013LKLIB0?psc=1&redirect=true&ref_=oh_aui_detailpage_o00_s00
I decided to order both!, I ordered the Huawei watch through Amazon at £329 with the metal strap. I felt safer in the knowledge the strap is made for the watch and comes under the same warranty with Amazon, plus Amazon are so good with returns I thought why not?
I haven't played with it too much yet as I am *still* awaiting on the moto 360. They've had the order since the 27th December but they've yet to dispatch it despite the order page saying it's ready to go.
First thoughts are - The presentation on this product is fantastic, it felt like I just bought an expensive piece of kit (technically I did?) The box, the decorating, the presentation was all very well done. It felt like a first class way of putting their device on display and for the first time in a long time, I spent so much time admiring the detail and effort that must of went into making this. However, whilst it is incredibly fancy I couldn't help but feel that once my excitement wore off, that this poor box will go into storage never to be seen and ideally with that in mind, would have liked the box it shipped in to be less deluxe so that the overall watch price would have been reduced.
The watch face feels small, which is odd as I don't even have anything to compare it to, I haven't worn a watch in months and like I said the 360 isn't here, but yet the screen feels small. The watch feels premium, screen is clear and crisp. Battery life seems better then I was expecting but again, I haven't dabbled with it too much just encase I return it.
The charging base seems a pain and could have been done better I feel. Why not have Qi charging? Or at least a decent stand? On that note, why not put that fantastic presentation box I mentioned to use and have that be part of the charging cycle.
The watch appears to be laggy, it doesn't seem fluid between the cards, or getting into the menus. Again I haven't set this watch up or spent that much time getting to know my way round it, plus with it being fairly new firmware updates should iron this out.
Overall I am happy with the watch, the box, the style, the feel and even the screen despite me thinking that it's kinda small. It's a lot of tech under a watch screen which is nothing short of amazing. However the cost of £329 is hard to swallow, I may return it for the leather strap one at £289 or may return it in favour of the 360 (if it ever gets here!)
I have used several watches. The Hauwei does lag some. I notice it more going into settings, it takes a second to open. Sometimes I think I missed a tap, but a second tap makes it go haywire. The hardware is identical to other watches that are smooth as butter, so it has to be a software setting. Perhaps they have the min cpu speed to slow or something. I dunno. It could be ironed out with an update or custom kernel.
The charging dock is kind of a pain compared to others. My LG G Watch has the same setup except the dock had a contoured lip around so it would slide into place with ease. It was also square = easier to align. The circle hauwei, when I dock, I have to semi spin it until it latches in. Even my ZenWatch2 just had a small magnetic clip and would snap on almost automatically.
The Hauwei is small. For me thats great because I am a smaller dude. My LG and Asus were big. The ZenWatch2 was good because of the curved screen. But my friends always called it my iPad Mini Watch.
The Motorola 360 has nice features but lacks a very important one; no speaker. And trust me, it is very important.
Heres why:
A watch is designed to give you personal freedom away from your phone. So I tend to not cling to it as much. It gets left on my desk, couch, charger, etc. When a call comes in... you find yourself scrambling to get to your phone. You typically do not have time to grab it and answer it, without some sort of awkward silence where you answered it from the watch and still in the process of grabbing the watch. Also when I am oncall for work, and in my pool swimming, I can dismiss unimportant emails and grab calls without having to kill myself trying to get out, dry off, and answer it before it goes to VM.
Food for thought. The speaker support was what I was waiting on to upgrade my LG G Watch. If you are going for just a cheap round smart watch, just buy the Moto 360 1st gen. I don't see the difference between them. Still has the flat tire and ****ty battery life.
Introduction
Generally, if you use a product and you like it, you don’t hesitate to go out and purchase another item from the same company. My Nexus 6P finally threw in the towel, leaving me to fend for myself out in the tech world. But... I was right in the middle of major phone upgrade season. The current flagships were on sale or being bundled with 256GB memory cards, *cough Samsung cough* but we were a few months from the next generations’ unveiling. Long story short, I decided on an HTC 10 to hold me over. It’s a great phone! Latest generation specs, an awesome camera, a nice speaker system, and a killer DAC to round things off. Unfortunately for my devices, I’m a power user- starting my day at 6:30 am and not getting back to the charger until 12 am (on an early night!) The HTC 10, like every other phone before it, simply didn’t have the stamina to last the 18ish hours in my typical day. So I went to Amazon, searched “ZeroLemon HTC 10”, and a smile broke across my face when I saw the first search result.
The Good Stuff
The good stuff? There’s a lot of it. It is a battery case through and through, which isn’t necessarily the most exciting thing on paper. But this case picks up where ZeroLemon’s Nexus 6P case left off. The build of the case itself is simplified, discarding the plastic ring that encased the device. Now it’s just three pieces: the silicon outside, the battery, and a “u” shaped double ended USB-C connector to transfer power into the case. This time around, a USB-A style connector is also hiding on the right side of the case, waiting to power up another device of your choosing. If you’re going to make a case with this big of a footprint already, little features like these are a huge value-add for the consumer, really justifying the size and price of the product. ZeroLemon’s team nailed the execution here! The silicon is much softer, and there are no signs of the injection molding process from their last case, lending to an overall more premium feel. Cutouts are all precise, however, the case does cover the HTC 10’s power and volume buttons, giving them a mushy feel, and making them trickier to identify by touch. The generous amount room around the headphone jack means you shouldn’t have a problem using any variation of auxiliary cables, and the four white LEDs that indicate the case's charge have good visibility. ZeroLemon also gives cutouts at the bottom of the case to allow sound from the bottom firing subwoofer to not be muffled and muddied. Qualcomm QuickCharge 3.0 still works here thankfully, as juicing up 11,500 mAh is no small feat. In my testing as a heavy phone user, I was able to go about three days on a single charge. That’s a whole lot of navigation, music streaming, being paired to a smartwatch, messaging, and some light gaming. This case does its job; if it’s battery life you want, it’s battery you’re going to get. I’d feel confident throwing this case on, and going out to a concert, or using it to keep my phone charged over a camping weekend.
The Not So Good Stuff
Put on this case, and your sleek aluminum unibody becomes 6.5” long, 3/4th of an inch thick, and quite hefty. For some reason, ZeroLemon chose to separate the connection from the phone to the case, resulting in the need for the little adapter. This adapter, in turn, adds about a half an inch of length to the phone and creates the odd jut out towards the bottom. This creates uniquely dissatisfying design decision. The rubber lip that sits on the phone’s display is prone to slipping off, especially when trying to slip the phone in and out of a pocket or bag.
Otherwise, I’m failing to find faults with this case. There are no issues with NFC, and thankfully there are no adverse camera effects. A final criticism to ZeroLemon: please stop waiting until a device has reached its first birthday before you put out a case for it!
Conclusion
ZeroLemon’s HTC 10 battery case is pretty simple. The company stumbled with their Nexus 6P case, having to re-engineer it after a defective first batch and some media criticisms. ZeroLemon seems to have come back with another 8500 mAh battery case and nearly nails it this time. The addition of a traditional USB port to share power with another device is a welcomed feature, and the inclusion of a speaker grille at the bottom sends a clear message: ZeroLemon is coming for the top. They’ve found a formula and are sticking with it for the most part. They’re trying to cram in a big battery and extra value. They’re thoughtful with design, and their designs are evolving from rough, flimsy plastics puzzles to sleek silicone sleeves.
Gallery: http://imgur.com/a/ArnBd
I'd love to try and answer any questions!
I'm glad you're happy with it but looks matter to me and this looks... far from perfect. I'd probably have a power bank on standby for when I needed one rather than have this attached to my phone. I will say that the 8500 mAh battery is impressive, that's almost 3 full charges.
So I received my zerolemon battery case and tried it few days ago , I won't be talking much and I will give my opinion straight forward ,
It's heavy and solid , yes it's ugly and no way you can keep it in your pocket , but it will charge your phone around 3 times before it runs out of charge
It took me 2 hours to charge my phone as its not using QC 3.0 , it's comparable with QC 2.0 speed I guess , it's not slow but it's just not as fast as QC 3.0
The battery case it self took around 3 hours to charge fully. And I really like how they made use of the huge design and included and USB A type output to charge whatever you want to , (could be your HTC 10 if u don't wanna hold put it inside the case )
It's like a normal 8.5K battery and it's wrapped inside a very soft anti slip rubber case that that holds your phone and battery together , the case has some holes left and right , which is yes makes the speaker fire straight at your face and that's just amazing , the left holes are for that tiny hole drilled mics on your HTC 10 .
I would really recommend buying that case especially if u spend alot of your time away from a socket , it can charge your phone 3x or you can use it to charge your other gadgets ..
Not soo great design , but very useful and reliable battery case from zerolemon
Until more battery cases use wireless charging (I know the HTC 10 does not have wireless charging), I'll be sticking with battery banks. Seeing the added height from these cases really makes me miss removable batteries.