I have had CM11 on my fire phone since September 2015. After I installed my sim card yesterday I noticed an increase in battery drain. Long story short I went to Safestrap boot to do a factory reset thinking that would bring it back to the original fire phone os. I rebooted the phone and it was still cyanogenmod. I went to the safestrap boot again and went to restore and chose the only folder that was there. After that my phone has been in a boot loop. When I try to reboot with the download option it just continues the boot loop. Is there anyway I can connect my phone to the computer and try to boot from a fire phone os zip file or side load from adb partition?
Related
Hey guys, I am pretty new at anything Android related and am in serious need of some help after several hours of struggling to revive my fire. Basically I took my stock kindle and installed a permanent root for the first time ever with the KF utility, after which I proceeded to install the latest TWRP Recovery using the same utility. Upon reboot after TWRP install, I immediately wiped the Dalvik cache and attempted to install the latest gedeROM build (26-6-2012). It seemed to flash ok, but on startup now the kindle will show the standard kindle fire logo, followed by the cyanogen 9 mod loading screen, at which it will stay in the animation forever, and never actually load up. Unfortunately in my noobness I did not realize that installing TWRP was not all I needed to do in order to achieve the option to boot into recovery mode every time, and now I cannot figure out how to once again get to that so I can install a backup of my stock firmware, which I did make. Is there a way to get the kindle into recovery mode without the ability to select that option when starting up? If I plug the kindle into my pc whilst it's stuck on the CM9 animation, the ADB status says online and has a boot status of 4000. When I attempt to send any commands to the kindle from the KF utility telling it to reboot into recovery, it just says waiting for device. I'm sure I just missed an obvious step along the way of the install, but I cannot seem to do anything with the kindle currently, so any help on reviving it would be fantastic!
Hey guys,
So few days ago I decided to do a factory data reset on my tablet since it was moving very slow. I activated it through settings (not recovery mode) and my tablet had about 35-40% of battery. Long story short, my tablet now is in boot loop, not showing anything else except "Samsung galaxy tab 3". The thing is that this is not the first time for her getting stuck there, before I had the same problem when tried to root it, but then I simply flashed a new stock ROM and everything worked fine. This time flashing a new ROM didn't help me, I also cannot access recovery mode, only download. What do I do now?
I have the same problem on my Tab 3. Hope someone has a solution to this problem.
I've been doing a lot of flashing lately, including the stock ROM via odin, and have found that the first boot doesn't complete... I shut it down, go into recovery, do a factory reset, then boot, and it comes up fine. I'm not sure why you can't access recovery mode, but if you can, maybe try that?
Removing the external SD card solved my problem, so if you have a SD card plugged in, remove it. You can plug it back when the boot animation will start (not the "Samsung Galaxy Tab 3" splash screen).
I am having major boot loop I flashed the rom and gaps after loading them thru adb Push ,but no matter what keep rebooting got the blue logo for a minute and go back to safe trap battery is ok!
I already post it in android development got no answer
Go into Amazon (not Safestrap) recovery and select sideload adb, then install the official Amazon image and see if that solves it. Do a factory reset after for good measure. You'll need to go through the whole Kingroot and Safestrap install again afterwards.
So I was using the TWRP app and Flashed to boot by accident instead of recovery. So when I go to recovery mode I just get stuck on the amazon logo
when I boot normally it goes into a bootloop getting stuck on the amazon logo and rebooting every time.
my PC recognized it still but ADB cant detect it anymore.
Is there anyway to fix this or did i permanently break it?
first gen fire tablet
Hey,
So I recently rooted my phone with SuperSU and it was the most sad and frustrating thing I did in my life to be honest... (3 days of: installing TWRP and rooting the phone......) so when I try to turn off and then turn on the phone or simply reboot it. It gets stuck in boot loop. I entered the recovery and clicked "reboot system" it worked after 2nd time or maybe even at the first attempt but is there any other method to fix the boot loop? Without factory reset or format data and without entering the recovery for the whole life when I want to reboot the phone? Please help..