bricked but with recovery mode/ twrp and download mode working - T-Mobile Samsung Galaxy S6 Edge

im an average user when it comes to rooting. flashed a new rom and then kernel and then ended up with bootloop. i didnt make a backup. we used kies 3 and smart switch for emergency firmware update, it finish the whole installation but when it comes to restarting the device it is still stuck on bootloop. after that we have tried flashing factory image including pit file. the firmware were tried to flash is G925TUVU3DOI1_G925TTMB3DOI1_TMB.ZIP and G925TUVU2DOH6_G925TTMB2DOH6 from sam mobile. halfway through installing the firmware we saw the cute android logo and then it says erasing.
the download mode now says
odin mode
[roduct name: sm-g925t
current binary: custom
system status: custom
frp lock off: off
secure download: enabled
knox warranty void: 1 (0x0304) tripped knox long time ago trying to root it. nothing bad happened
AP SWAREV: B:3 K:2 S:2
factory recovery mode says efs not mounted. were able to push files through adb fastboot.
would gladly appreciate if anyone can help us. thankyou

I noticed you said you tried to flash a .zip file through ODIN. I'm not sure if that normally works, but everything I flash through ODIN is a .tar or .tar.md5 file. There is a link to download the full stock DOI1 firmware somewhere on here. Find it and try to flash that, and then re-root using UniKernel.
Edit: Here is the thread with the DOI1 firmware file. Be sure to thank @Alex9090 for posting it.
http://forum.xda-developers.com/tmobile-galaxy-s6-edge/general/g925tuvu3doi1-download-mega-t3221088

Akw6190 said:
I noticed you said you tried to flash a .zip file through ODIN. I'm not sure if that normally works, but everything I flash through ODIN is a .tar or .tar.md5 file. There is a link to download the full stock DOI1 firmware somewhere on here. Find it and try to flash that, and then re-root using UniKernel.
Edit: Here is the thread with the DOI1 firmware file. Be sure to thank @Alex9090 for posting it.
http://forum.xda-developers.com/tmobile-galaxy-s6-edge/general/g925tuvu3doi1-download-mega-t3221088
Click to expand...
Click to collapse
i apologize. the initial factory firmware i flashed was an md5. i also tried the zip through the twrp.
i just tried it again. its the same thing. odin says
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin engine v(ID:3.1100)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/007> Added!!
<ID:0/007> Odin engine v(ID:3.1100)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> SingleDownload.
<ID:0/007> sboot.bin
<ID:0/007> NAND Write Start!!
<ID:0/007> cm.bin
<ID:0/007> boot.img
<ID:0/007> recovery.img
<ID:0/007> system.img
<ID:0/007> cache.img
<ID:0/007> modem.bin
<ID:0/007> RQT_CLOSE !!
<ID:0/007> RES OK !!
<ID:0/007> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/004> Added!!
after that the android logo showed up saying "installing system" with 1/3 of the loading bar. then immediately says erasing.

godefroy28 said:
i apologize. the initial factory firmware i flashed was an md5. i also tried the zip through the twrp.
i just tried it again. its the same thing. odin says
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin engine v(ID:3.1100)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/007> Added!!
<ID:0/007> Odin engine v(ID:3.1100)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> SingleDownload.
<ID:0/007> sboot.bin
<ID:0/007> NAND Write Start!!
<ID:0/007> cm.bin
<ID:0/007> boot.img
<ID:0/007> recovery.img
<ID:0/007> system.img
<ID:0/007> cache.img
<ID:0/007> modem.bin
<ID:0/007> RQT_CLOSE !!
<ID:0/007> RES OK !!
<ID:0/007> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/004> Added!!
after that the android logo showed up saying "installing system" with 1/3 of the loading bar. then immediately says erasing.
Click to expand...
Click to collapse
Hm. It looks like the ODIN flash didn't fail, which leads me to believe the firmware you flashed was somehow bad. Maybe try downloading the firmware from a different site? But if you got it from Sammobile, it should be good though. Curious. I still recommend trying a different download. Short of that I have no more suggestions. Sorry I couldn't be of any more help. I hope you get it figured out.

Related

7100 rom on LTE 7105

By mistake friend of mine flashed wrong rom from7100 on 7105
i tryed maybe ewerything on forum but no luck .I tryed emergency recovery no luck restore stoped.With odin and oficial stock when it comes to write modem it fails.
I dont have any samsung service in my country,So if it`s anyone have experience with this please help.
latest ODIN and stock rom from sammobile
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> boot.img
<ID:0/007> NAND Write Start!!
<ID:0/007> recovery.img
<ID:0/007> system.img
<ID:0/007> modem.bin
<ID:0/007> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
regards

[Q] Galaxy note 2 (SPH-L900) Won't let me flash stock rom.

Last Night my Note2 finally got the 4.4 upgrade which I let install. Upon waking up I was greeted with my phone staying on the Samsung logo (it was doing the glowing animation both on the logo and the LCD so it wasn't frozen as far as I know). I've been trying all day to get it to work, I even tried flashing the Stock rom (KIES_HOME_L900VPAMC2_L900SPTAMC2_1090526_REV04_user_low_ship.tar.md5) via ODIN v3.07, unfortunately I keep getting the following when I try to flash the recovery:
<OSM> KIES_HOME_L900VPAMC2_L900SPTAMC2_1090526_REV04_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> boot.img
<ID:0/004> NAND Write Start!!
<ID:0/004> cache.img
<ID:0/004> hidden.img
<ID:0/004> modem.bin
<ID:0/004> recovery.img
<ID:0/004> sboot.bin
<ID:0/004> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
I've also tried Samsungs Kies Software and I haven't had any luck.
Can someone please help or at least point me in the right direction?
Any help is very appreciated.
Thank you so much
4.4.2 odin .tar file is available now:
http://forum.xda-developers.com/showthread.php?t=2780984
916
DaniLuv said:
Last Night my Note2 finally got the 4.4 upgrade which I let install. Upon waking up I was greeted with my phone staying on the Samsung logo (it was doing the glowing animation both on the logo and the LCD so it wasn't frozen as far as I know). I've been trying all day to get it to work, I even tried flashing the Stock rom (KIES_HOME_L900VPAMC2_L900SPTAMC2_1090526_REV04_user_low_ship.tar.md5) via ODIN v3.07, unfortunately I keep getting the following when I try to flash the recovery:
<OSM> KIES_HOME_L900VPAMC2_L900SPTAMC2_1090526_REV04_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> boot.img
<ID:0/004> NAND Write Start!!
<ID:0/004> cache.img
<ID:0/004> hidden.img
<ID:0/004> modem.bin
<ID:0/004> recovery.img
<ID:0/004> sboot.bin
<ID:0/004> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
I've also tried Samsungs Kies Software and I haven't had any luck.
Can someone please help or at least point me in the right direction?
Any help is very appreciated.
Thank you so much
Click to expand...
Click to collapse
Michael just helped me out in this thread I made, having the same issue as you. That fix.tar really helps! Just read his post in this thread: http://forum.xda-developers.com/showthread.php?t=2780409

[Q] help and need some info about gt-19192 unbrick

im new user of samsung my brother mobile once didnt wanna to start the rom then i try the odin to flash it didnt wanna to flash or start rom stuck on battry screeen only no recoery or anthing just download mode and not working to i restart it many times once it open rom and give me update 1 of 2 then it finsh and close and didnt start i flash roms but field i tried to flash recovery but gave me in all <ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> recovery-clockwork-6.0.5.1-serranodsdd.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin engine v(ID:3.1005)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> SingleDownload.
<ID:0/007> recovery.img
<ID:0/007> NAND Write Start!!
but it flash the pit file successful the only file so what can i do ??
if the debrick.img will help me or download another rom or what ?
(im useing original usb of samsung and htc and the drivers updated and my windows win 10 and xp and i use all usb port and odin 3.10.6 1.8 3.7 and Heimdall Suite stuck in the same as odin )
Download Samsung stock firmware from Sammobile.com and flash it through odin 3.09
Go to download mode (vol down + home+ power). Then press vol up
Extract the downloaded zip file, u will get a .tra.md5 file
Add that file to the PDA, it will take few seconds. Repartition and F.Reset time check box should be UNCHECKED.
Then press the start button.
First boot will take some time (25 mins)
Wipe factory data and cache partition.
Sent from my GT-I9195 using XDA Free mobile app
oky im downloading now how to know the witch the stock firmware of my device
Odin mode
product name: gt-i9192
current binary:custom
system kernel: custom
Knox kernel lock: 0x0
Knox warranty void: 0x1
csd-config-lsb: 0x30
boot loader AP swrev: 2
write protection: enable
Click to expand...
Click to collapse
so any one or download any one ?
Shukry Faiz said:
Download Samsung stock firmware from Sammobile.com and flash it through odin 3.09
Go to download mode (vol down + home+ power). Then press vol up
Extract the downloaded zip file, u will get a .tra.md5 file
Add that file to the PDA, it will take few seconds. Repartition and F.Reset time check box should be UNCHECKE
Sent from my GT-I9195 using XDA Free mobile app
Click to expand...
Click to collapse
the same 2 roms
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9192UBUCOC2_I9192ZTRCOC2_I9192UBUCOC2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin engine v(ID:3.1005)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> SingleDownload.
<ID:0/007> aboot.mbn
<ID:0/007> NAND Write Start!!
<ID:0/007> FAIL!
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<OSM> All threads completed. (succeed 0 / failed 0)
<ID:0/007> Removed!!
<OSM> All threads completed. (succeed 0 / failed 0)
<ID:0/007> Added!!
<ID:0/007> Odin engine v(ID:3.1005)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Set PIT file..
<ID:0/007> DO NOT TURN OFF TARGET!!
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> SingleDownload.
<ID:0/007> aboot.mbn
<ID:0/007> NAND Write Start!!
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/007> Removed!!
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1005)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> aboot.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
likenoother94 said:
the same 2 roms
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9192UBUCOC2_I9192ZTRCOC2_I9192UBUCOC2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin engine v(ID:3.1005)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> SingleDownload.
<ID:0/007> aboot.mbn
<ID:0/007> NAND Write Start!!
<ID:0/007> FAIL!
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<OSM> All threads completed. (succeed 0 / failed 0)
<ID:0/007> Removed!!
<OSM> All threads completed. (succeed 0 / failed 0)
<ID:0/007> Added!!
<ID:0/007> Odin engine v(ID:3.1005)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Set PIT file..
<ID:0/007> DO NOT TURN OFF TARGET!!
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> SingleDownload.
<ID:0/007> aboot.mbn
<ID:0/007> NAND Write Start!!
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/007> Removed!!
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1005)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> aboot.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
First Reboot to Recovery and Wipe Data/Factory Reset, Wipe Cache and Dalvik Cache
then install rom through Odin
then all threads will be succeeded.
likenoother94 said:
the same 2 roms
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Try to flash latest version of KitKat . I think u try to flash an older version on your phone that is why it fails at aboot ( bootloader )
SilviuMik said:
Try to flash latest version of KitKat . I think u try to flash an older version on your phone that is why it fails at aboot ( bootloader )
Click to expand...
Click to collapse
that's the 2 roms i download them from sammobile.com
I9192XXUBNB1_I9192OJVBNB1_EGY
I9192UBUCOC2_I9192ZTRCOC2_ZTR
if it not the right can u give me
the link of the rom :crying:
it stuck in recovery or boot loader or anything but the pit file alone goes succeed
likenoother94 said:
that's the 2 roms i download them from sammobile.com
I9192XXUBNB1_I9192OJVBNB1_EGY
I9192UBUCOC2_I9192ZTRCOC2_ZTR
if it not the right can u give me
the link of the rom :crying:
Click to expand...
Click to collapse
With COC it should have worked . I`m sorry no idea other then phone repair
SilviuMik said:
With COC it should have worked . I`m sorry no idea other then phone repair
Click to expand...
Click to collapse
dont have recovery ?? :crying: all i have odin mode @sajid0786
likenoother94 said:
dont have recovery ?? :crying: all i have odin mode @sajid0786
Click to expand...
Click to collapse
See these links if these help you
Check This
Check This
sajid0786 said:
See these links if these help you
Check This
Check This
Click to expand...
Click to collapse
nothing thankx for help :crying:

NOTE 8 - odin nand write fail errors

Hello,
I had flashed CM 11 and wanted to return to stock - I tried flashing NE2 in download mode using odin and it keeps failing with a nand write fail in odin? Any ideas? Knox is 0x1 (from long ago), I don't care about the knox. Is there a way to flash back to stock from Philz recovery which is currently installed and I can boot to recovery.
EDIT would a low battery level (5%) cause the nand write errors? I am charging it now to 100 % before attempting again.
Thanks.
cybershawngates said:
Hello,
I had flashed CM 11 and wanted to return to stock - I tried flashing NE2 in download mode using odin and it keeps failing with a nand write fail in odin? Any ideas? Knox is 0x1 (from long ago), I don't care about the knox. Is there a way to flash back to stock from Philz recovery which is currently installed and I can boot to recovery.
EDIT would a low battery level (5%) cause the nand write errors? I am charging it now to 100 % before attempting again.
Thanks.
Click to expand...
Click to collapse
Below with NE1 one-click
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> sboot.bin
<ID:0/007>
<ID:0/007>
<OSM> All threads completed. (succeed 0 / failed 1)
SW REV CHECK FAIL DEVICE 2 BINARY 1
I tried it with N5100XXDNL5_N5100OXADNL5_N5100XXDNH3_HOME.tar.md5
\
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N5100XXDNL5_N5100OXADNL5_N5100XXDNH3_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> sboot.bin
<ID:0/007> NAND Write Start!!
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<ID:0/007> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
solved it - it just turned out to be patience and downloading the correct firmware.
I went to sammobile.com (which is official samsung I didn't know).
Search for GT-N5110
Got 4.4.2 (Poland - I didn't see U.S. but I'm told the wifi versions are all the same).
Used Odin 3.09 as administrator.
Official Samsung Cable
Charged to 100%
THe one i Used was N5110XXDNF1_N5110XEODNF1_XEO
(EDIT While that works, it's only good if you speak polish. Finally found the right one:
N5110UEU2CNE2_N5110XAR2CNE2_XAR - XAR is the code for USA

[Q] Help with Odining TWRP - THIS CAN BE DELETED

Trying to Odin twrp and it wont stick.
I am on OJ6
Figured alls I would have to do is odin twrp latest version 2.8.7.0 and
using either odin version 3.07 or 3.10.7
Cant seem to get it to work in 3.07 using pda option or 3.10.7 using AP option....
EDIT: I also did this and nothing. when you Odin TWRP, uncheck auto reboot and when you get the success confirmation, pull USB and battery, wait 30 seconds and boot into recovery (tried twrp no go, was able to get back into the onboard recovery)
Odin results:
<ID:0/007> Added!!
<ID:0/007> Odin engine v(ID:3.1100)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> SingleDownload.
<ID:0/007> recovery.img
<ID:0/007> NAND Write Start!!
<ID:0/007> RQT_CLOSE !!
<ID:0/007> RES OK !!
<ID:0/007> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
EDIT 2: Thanks all for your help...Figured out!!!! Had to odin N910PVPU4COJ6_N910PSPT4COJ6_SPR.zip to go back to stock...even tho i took the ota to OJ6. once i did this i was able to get recovery to flash. Now i am running stock rooted!
THIS THREAD CAN BE CLOSED

Categories

Resources