Related
So I'm looking into the possibility of making a wireless charging solution on my own. I have lots of wireless chargers at home, work, in the car, and I would really benefit from getting wireless charging working.
I took a USB Qi charging coil and soldered wires, which I then attached (well, just touched ) to either end of the magnetic connector, and it worked.
The difficulty I'm facing is, how can I keep these wires touching the magnetic charging port semi-permanently without doing anything dangerous like attempting to solder it directly.
So I'm wondering if anyone has any neat ideas of how I might rig this up. Any ideas would help a lot! If I come up with something good, I'll make a guide so others can do it.
You could try to get someone to 3D print a side piece similar to the one on the Z3 wireless charging case from sony: http://www.sonymobile.com/us/products/accessories/wireless-charging-cover-wcr14/
Have them leave chambers to run the wire through.
JCBomb said:
You could try to get someone to 3D print a side piece similar to the one on the Z3 wireless charging case from sony: http://www.sonymobile.com/us/products/accessories/wireless-charging-cover-wcr14/
Have them leave chambers to run the wire through.
Click to expand...
Click to collapse
I've been thinking about making my own wireless charging case similar to the sony branded case but using high quality leather, and an oem qi charging circuit with a 3d printed base clip with the circuit connectors integrated into the clip, just to ensure constant connectivity.
just looking into prices for scrap leather now.
duraaraa said:
So I'm looking into the possibility of making a wireless charging solution on my own. I have lots of wireless chargers at home, work, in the car, and I would really benefit from getting wireless charging working.
I took a USB Qi charging coil and soldered wires, which I then attached (well, just touched ) to either end of the magnetic connector, and it worked.
The difficulty I'm facing is, how can I keep these wires touching the magnetic charging port semi-permanently without doing anything dangerous like attempting to solder it directly.
So I'm wondering if anyone has any neat ideas of how I might rig this up. Any ideas would help a lot! If I come up with something good, I'll make a guide so others can do it.
Click to expand...
Click to collapse
Have you tried tape? It would be covered up by your case anyway, right?
PuffDaddy_d said:
Have you tried tape? It would be covered up by your case anyway, right?
Click to expand...
Click to collapse
I've thought of tape but I've yet to figure out a way to tape it where it will definitely stay in place.
I might be able to get a case that would cover it, but my current cases have holes so that magnetic chargers could be plugged in.
I've decided to try using copper tape to connect a Qi coil to the magnetic dock port. I'll see how it goes. Hopefully it will be as easy as I'm hoping it will be.
So I finally managed to make it work. Unfortunately, I had to solder.
I gave up with trying to line things up just right and keep it in place, so I just soldered a Qi receiver to the magnetic charging port, wrapped it around to the back of the phone, and fit in a case. It charges wirelessly now, so I'm happy. Unfortunately, I don't know if I'll ever be able to clean it up in the future if I want to sell the phone. But to me, wireless charging was super important. I was also able to continue using my Z1C battery case which uses the magnetic port, so I'm pretty happy with the end result.
Pics?
it's ugly, but I'll put up pics when I get a chance.
Pictures as promised. I had been concerned adding this might block NFC, but NFC works just fine. Obviously, magnetic charging cables don't work (but a Z1C charging case I have does.)
It adds some thickness behind it so the case doesn't fit quite perfectly, but well enough to stay on. I didn't have thinner cables, but having some might have been able to decrease the thickness. Also, I'm not necessarily good at soldering, so I just did what I could.
But I can charge it on my bedside table and in my iOttie Qi dock in my car, so I'm cool with it.
hmm not pretty, but i guess it works. how is the charging speed?
you should be able to clean it up fine if you use some solder wick.
Awesome job!
Can you please give us a link for the receiver?
All I can find are with usb
ugly doesn't even start describing it... seriously, you ruined that phone. You could've cannibalized a 3rd party docking station instead
duraaraa,
Thanks for blazing this trail for us, mighty brave to solder to your phone like that! Now that you've had this set up for a few weeks, is it holding up ok? I'd just about give my left nut for an actual phone case that simply has a wireless receiver built in and taps into the magnetic charger pins, but I doubt anyone will ever make one since (I believe) the Z3C is discontinued. I mean, they make those giant external battery packs for the Z3C that use the pins, so why not a qi-compatible one??? Anyway, no way I'm soldering to my pins so I'm basically trying to mold a connector out of epoxy that I can squeeze between the side of the case and the pins. (Basically I pushed one of my magnetic cable connectors into a clay bar and filled w/epoxy.) It's still drying so I have no idea if it's feasible at all, but wanted to pop in and say thanks for the inspiration.
mralexsays said:
duraaraa,
Thanks for blazing this trail for us, mighty brave to solder to your phone like that! Now that you've had this set up for a few weeks, is it holding up ok? I'd just about give my left nut for an actual phone case that simply has a wireless receiver built in and taps into the magnetic charger pins, but I doubt anyone will ever make one since (I believe) the Z3C is discontinued. I mean, they make those giant external battery packs for the Z3C that use the pins, so why not a qi-compatible one??? Anyway, no way I'm soldering to my pins so I'm basically trying to mold a connector out of epoxy that I can squeeze between the side of the case and the pins. (Basically I pushed one of my magnetic cable connectors into a clay bar and filled w/epoxy.) It's still drying so I have no idea if it's feasible at all, but wanted to pop in and say thanks for the inspiration.
Click to expand...
Click to collapse
hows your build coming along mate I'd love to see how it looks.
kstanley7 said:
hows your build coming along mate I'd love to see how it looks.
Click to expand...
Click to collapse
Not good I'm afraid my friend... My first attempt (trying to mold a connector out of epoxy using a clay mold) failed, the thing came out looking like a chewed up piece of gum and just wouldn't work. My next attempt involved slicing up a couple of cheap magnetic adapters and cables to try to trim down the connectors to something reasonably sized, but they become really brittle when you cut them that thin... Unfortunately, I think it'd take someone with some type of plastic molding equipment or maybe a 3d printer (that is capable of making really small, fine-detail parts) to make this thing. I'm still disappointed that Sony makes a wireless case for the Z3, but not the Z3C, but I've also come to realize that the Z3C has such good battery life that maybe I don't really need such a case. (I come from a long line of Nexus, HTC, and Samsung devices so I've become somewhat of a charging addict!)
tl;dr: Just enjoy the Z3C and use the handy magnetic dock for overnight charging.
just looking at the magnetic connectors on the z3c I think there might be a way but it'll add a couple more mm to the height, would need to get someone with a 3d printer, but if the wallet is made of leather and is inserted underneath, with the qi wireless pad, and two wires made into connection terminals which would then clip onto the phone so a solid connection is made between those terminals.
Just to answer some questions, it's held up. I think it's fine -- anyone desperate for Qi should just bite the bullet and solder. Charging speed is similar to really any other Qi-charged device.
apis10 said:
Awesome job!
Can you please give us a link for the receiver?
All I can find are with usb
Click to expand...
Click to collapse
Sorry my response is so late!
It's the USB type. I un-soldered the USB ribbon and soldered a wire for the two connections.
So you would want to buy the USB version, I think.
Look into copper tape. I attempted this a little while back but I think my charging pad wasn't powerful enough. What charging pad are you using?
As we all know, the new Zenfone 2 is missing wireless charging capabilities, however there are multiple solutions to enable wireless charging on basically any phone.
Example is http://www.amazon.com/BEZALEL®-Wire..._1_4?s=wireless&ie=UTF8&qid=1432149451&sr=1-4
It is a cover with a Qi receiver built in, which connects to the charging port and it also provides an independent micro usb port as a part of the case.
The absence of wireless charging in Zenfone 2 is a deal breaker for me ( don't judge) and as soon as an appropriate case is available, I'll get it and the phone as well.
Please post your findings here.
Would love to use wireless charging but using a cover like the one posted is out of question.
I love the slim form and feel of this phone. so i will have to live without QI and other solutions.
This will occupy the mUSB port but would probably be the best current solution.
hkdmjack said:
This will occupy the mUSB port but would probably be the best current solution.
Click to expand...
Click to collapse
That's pretty cool. I like wireless charging because I'd rather not wear out my micro usb...but that setup kinda marries you to wireless charging all the time. I'd have to rig up wireless charging in the car and at work...not just at home. You use something like that?
nathan118 said:
That's pretty cool. I like wireless charging because I'd rather not wear out my micro usb...but that setup kinda marries you to wireless charging all the time. I'd have to rig up wireless charging in the car and at work...not just at home. You use something like that?
Click to expand...
Click to collapse
Not sure if I'm going to stick with the ZF2, so I haven't gone out and done all that yet but qi adapters are pretty cheap now for both home and car. How effective some of the car ones are though are another story. iOttie has two models out now that look promising for the car.
There may also be the possibility of placing those adapters into a separate case just meant for wireless charging... remove the case if you need the mUSB port.]
Or... if they do release new back covers... get one that you install the qi adapter in and then one that you won't have the qi adapter in.
WHYYYYYYYYY
Why did Asus decide not to include the qi pins in the back ((((((((((((((((((((((((((((((((((((((((((((
>_<
what to do :'(
Here's a teardown: http://www.myfixguide.com/manual/asus-zenfone-2-teardown/
You could solder the DigiYes posted earlier (http://www.amazon.com/gp/product/B00HI8JYFE) onto the usb board. Or you could probably just jam the wires into the connector for a non-permanent solution. The pictures of the DigiYes are a little conflicting, but if it does have leads for the data pins, you'd be best off omitting them (you'll be limited to 500ma qi charging).
This is of course assuming there's enough space to wedge the DigiYes between the back cover and phone.
ziddey said:
Here's a teardown: http://www.myfixguide.com/manual/asus-zenfone-2-teardown/
You could solder the DigiYes posted earlier (http://www.amazon.com/gp/product/B00HI8JYFE) onto the usb board. Or you could probably just jam the wires into the connector for a non-permanent solution. The pictures of the DigiYes are a little conflicting, but if it does have leads for the data pins, you'd be best off omitting them (you'll be limited to 500ma qi charging).
This is of course assuming there's enough space to wedge the DigiYes between the back cover and phone.
Click to expand...
Click to collapse
Which goes back to my point. Why did Asus purposdely omit to include QI/wireless charging pins on the back? It would had cost them hardly anything extra at all, and users could just have changed back cover to get wireless charging...
That one http://www.amazon.com/BLUBOON-Unive...2630&sr=8-2&keywords=qi+wireless+charger+1000 is 1000mA, if it does make a difference. But a case integrated receiver would be much better solution, if ever.
olegy said:
That one http://www.amazon.com/BLUBOON-Unive...2630&sr=8-2&keywords=qi+wireless+charger+1000 is 1000mA, if it does make a difference. But a case integrated receiver would be much better solution, if ever.
Click to expand...
Click to collapse
I bought that model. I have a Qi charger (used with a Nexus 5) hooked up to a 2A USB Adapter, and it barely charges the Zenfone. I do not recommend. Maybe a 2A receiver would work better.
It's ridiculous.... why did asus decide not to offer a wireless charging solution similar to the previous samsung galaxies/lg.
Have the pins for charging on the back, and let the user change the case to a qi receiver case or add a qi receiver pad inside. this is honestly the only thing that disappoints on this phone (((((((((((((
ziddey said:
Here's a teardown: http://www.myfixguide.com/manual/asus-zenfone-2-teardown/
You could solder the DigiYes posted earlier (http://www.amazon.com/gp/product/B00HI8JYFE) onto the usb board. Or you could probably just jam the wires into the connector for a non-permanent solution. The pictures of the DigiYes are a little conflicting, but if it does have leads for the data pins, you'd be best off omitting them (you'll be limited to 500ma qi charging).
This is of course assuming there's enough space to wedge the DigiYes between the back cover and phone.
Click to expand...
Click to collapse
I just received mine and there is enough space in the back cover for the receiver to fit in, albeit with a small bulge. It does show my phone as charging even when just held up to my Moto 360 cradle; whether or not it's charging, however, I have no idea.
raynan said:
I just received mine and there is enough space in the back cover for the receiver to fit in, albeit with a small bulge. It does show my phone as charging even when just held up to my Moto 360 cradle; whether or not it's charging, however, I have no idea.
Click to expand...
Click to collapse
Thanks for trying. Did you actually solder or just plug it in the usb port? If you plugged it in the usb port, does the cover close without damaging the cable?
I'm asking because if that works, we could potentially design a slightly thicker but hollow back case that could hold NFC and the wireless receive without unnatural bulges.
ameel said:
Thanks for trying. Did you actually solder or just plug it in the usb port? If you plugged it in the usb port, does the cover close without damaging the cable?
I'm asking because if that works, we could potentially design a slightly thicker but hollow back case that could hold NFC and the wireless receive without unnatural bulges.
Click to expand...
Click to collapse
It closes fine but there is a bulge and the cover is left slightly open.
Here's my solution. Doesn't look good but functional.
don't judge
Click to expand...
Click to collapse
Yeah I judge, wireless charging its just another feature. A small battery, a slow processor or low memory now that's a real deal-breaker since your phone wont last a day, apps will run like hell and you will always have to micromanage just for things to run properly.
I'm way more pissed off at this phone not having a removable battery, not just because its a real deal-breaker during travel where I will be forced to lug around one of those brickish power banks but because Li-ION batteries have the lifespan of a mosquito. I already had 2 phones like that and the result was always a massive pain in the ass to deal with.
I rather buy a case with an extra battery than this thing
Three pins USB Board?
Hi there
Maybe some one knows, what are those three pins on the USB board, that are accessible without disassembly phone?? That should be connectors to charging instead of usb socket?
I have a qi charger built into my car. I do not like aftermarket charger added to the phone. So this is a deal breaker for me and will not consider any phones without buildin qi charger.
Looking to buy this phone and own a quick charging card like this. Is it possible to slip the card under the back cover (without a case) or will it cause it to bulge in too unsightly a manner?
dud89 said:
It closes fine but there is a bulge and the cover is left slightly open.
Here's my solution. Doesn't look good but functional.
Click to expand...
Click to collapse
Slooop said:
Looking to buy this phone and own a quick charging card like this. Is it possible to slip the card under the back cover (without a case) or will it cause it to bulge in too unsightly a manner?
Click to expand...
Click to collapse
It can but causes a gap near the usb port that I could not close. I would've run it inside if it didn't do that.
dud89 said:
It closes fine but there is a bulge and the cover is left slightly open.
Here's my solution. Doesn't look good but functional.
Click to expand...
Click to collapse
Great Idea.
The speed of charge is 350 MAH ?? Is to slowly (USB PC charge normally 550 MAH)
Okay... i´m trying to make a mod for my Z1C to make it qi compatible....
I have the magnetic connector from a dock (which is broken).
So, using the connector + cover + glue can make it work.... and of course, need to solder the receiver to the connector....
But, the big question... which receiver should i use?
First of all, i´m from Argentina... so i have a limited access to receivers.
I´ve seen here receivers from Samsung Galaxy S3, S4, S5, Note III and Note 4, and a few others generic...
The maximum current that could find was 650mA... but read some comments that the output 1000mA is a lie... and there is no difference between the receivers...
So, which one should i buy?
Thanks to all!!
Finally, get a 700mAh receiver, and cutting out the cable, mixing + soldering + glueing it all together, and now it´s working....
Samsung GS4 1000mA QI receiver
I have a few Galaxy S4(1000mA)/S3(800mA) QI receiver cards.
The cards are different depending on the contact points location in the phones.
So you just soldered the internal magnetic charging points to a QI receiver card inside the phone?????
If you have the QI Receiver inside the phone (only real place for it), how much pressure does that place on the back cover??
The back cover tends to break away from the frame without much effort, so having the raised 'bulk' of a Qi card in the phone would only add to the pressure for the back cover to separate.
On Samsung phones (GS4 which I've added QI cards) it does take a bit of brute force to chip the back cover on again and some GS4 aftermarket cases/covers can not be used with the QI card installed due to the back of the phone being ever so slightly raised.
I have the QI receiver cards, glue seals rings for Z1C back cover and the Qi chargers and it is something I have thought about, but with three working magnet DK32 docks around the house, it's not something I have advanced at this time.
Well done for getting it to charge via QI charger if that is what you've done.
Maybe a photo would be nice.
Okay... now, the photos:
The tape is over the receiver module.
The original contacts from the receiver were removed, and over there, was soldered some copper tape (that can be seen in the photos).
The contacts were made by opening-cutting a magnetic cable, soldering it to the copper tape, and then glueing it to the cover, to maintain position.
The charger seems to be very picky about position. Searching over the internet, seems to be a common issue with this model...
Hope it´s usefull...
Well... about the charger, there seems to be an easy fix to it's pickiness... Take off the upper side... That way, the thing will gone a cool itself, and the connection will become a lot easier...
I'm looking to buy a new car mount for my Galaxy S8+. Currently I have a 5 year old Brodit car mount that can be flexible in size, but the downside is that it's very shaky and loose.
I've been looking into the force touch charger car mount from Mophie because of the magnetic attachment, but it can only be used with their battery case and I don't need such a bulky case.
Can any of you recommend a good car mount?
I had an iBolt mPro I was using with my previous phone and it worked pretty solid. I just ordered the cPro (which has the USB-C connector built in) and I'll let you know how it works out.
I like the iottie holders since you can put it in and take it out with one hand. However i'm looking at this new one which also includes wireless charging while in the holder.
https://www.iottie.com/Product/Deta...Wireless-for-Android-_-Qi-Enabled-Smartphones
icewolf293 said:
I like the iottie holders since you can put it in and take it out with one hand. However i'm looking at this new one which also includes wireless charging while in the holder.
https://www.iottie.com/Product/Deta...Wireless-for-Android-_-Qi-Enabled-Smartphones
Click to expand...
Click to collapse
What do you mean by new? Seems to have come out in 2015 .. I'm also thinking about purchasing but seems old for a couple month old phone. Has anyone tried it? I'm hoping to be able to charge while the phone is in use. I have a 1.5 amp USB in the car which I hope is enough.
Drey070 said:
What do you mean by new? Seems to have come out in 2015 .. I'm also thinking about purchasing but seems old for a couple month old phone. Has anyone tried it? I'm hoping to be able to charge while the phone is in use. I have a 1.5 amp USB in the car which I hope is enough.
Click to expand...
Click to collapse
You can get a fast charger though I've noticed mine is sensitive to heat, doesn't take much for it to start slowing down charging (and warning you about it)
If you are looking for magnetic attachment, I suggest you look at xvida magnetic mounts. They offer a magnetized cover for S8 which would allow you to use their regular magnetic car docks as well as their line of qi car docks. I've tested their cases for S7 edge & charging desk stand and charging vent mount and they work great. Slight overheating with the car docks though, which can be expected but like I said, they have various standard magnetic car docks if that's a concern. No problems with overheating with their desk charger if you are on the market for a charging stand as well.
HANDS DOWN the best case/mount combo is made by Evutec. The cases themselves are precisely cut and essentially indestructible, all while containing a thin metal insert to work with their vent mount (make sure you get one that comes with the mount). Theyre relatively inexpensive on Amazon for the quality of case you get. They typically only make iPhone cases, but fortunately make them for the S8 and S8+.
The only caveat is that they don't play nice with wireless charging. I guess this could be a big downside for people that love the wireless charging, but I charge by a cable and don't own a wireless charge pad so its all good.
sudkcoce said:
If you are looking for magnetic attachment, I suggest you look at xvida magnetic mounts. They offer a magnetized cover for S8 which would allow you to use their regular magnetic car docks as well as their line of qi car docks. I've tested their cases for S7 edge & charging desk stand and charging vent mount and they work great. Slight overheating with the car docks though, which can be expected but like I said, they have various standard magnetic car docks if that's a concern. No problems with overheating with their desk charger if you are on the market for a charging stand as well.
Click to expand...
Click to collapse
Thank you so much! It was something like that I was looking for. Magnetic attachment and fast qi charging!
I've been on Youtube for the last hour reviewing magnetic qi car chargers.
Obviously, they all differ considerably for each phone.
I'm looking for one that just has a flat front surface with no arms or clamps, so this means that a magnet of some kind has to go on the phone cover that I have on my P5.
There are vent and windscreen mount versions, I'm looking for one that is as unnoticeable as possible, so forget the windscreen mount type.
Has anyone got any experience with one of these. Whatever I get must not interfere when charging my P5 on the Google Pixel Stand.
Thanks
How is your phone going to stick to a magnetic mount?
With a metal plate inside the phone cover, placed carefully so it does not interfere with the wireless charging on my Pixel Stand and whatever I get for the car. I've had a normal magnetic mount in the car before using this method and it did not interfere with the wireless charging, as long as its placed properly.
The problem with the Pixel 5, and, to some extent, all phones with wireless charging, is that the location of the space for positioning the metal plate is either at the very top or the very bottom of the phone, thus making the phone either very bottom heavy or top heavy and prone to sliding and slippage.
Apple's MagSafe gets around this because their magnetic mounting system is built around the charging coil so as to not interfere with charging and provide a multipoint magnetic connection that is centered, more secure, and stays in alignment.
The only alternative that I've found that works for Android phones and works well is a system like the Mous Limitless system of cases and accessories. I've been using their case, card wallet, and charger mount for about a month now and they are great. If you want more info on them you can just read my post in the thread below this one where I detail my experience with their products. They also have their own info and explainers on their site at mous.co.
jallenhayslett said:
The problem with the Pixel 5, and, to some extent, all phones with wireless charging, is that the location of the space for positioning the metal plate is either at the very top or the very bottom of the phone, thus making the phone either very bottom heavy or top heavy and prone to sliding and slippage.
Apple's MagSafe gets around this because their magnetic mounting system is built around the charging coil so as to not interfere with charging and provide a multipoint magnetic connection that is centered, more secure, and stays in alignment.
The only alternative that I've found that works for Android phones and works well is a system like the Mous Limitless system of cases and accessories. I've been using their case, card wallet, and charger mount for about a month now and they are great. If you want more info on them you can just read my post in the thread below this one where I detail my experience with their products. They also have their own info and explainers on their site at mous.co.
Click to expand...
Click to collapse
Thanks for that and the mous info, funny, I was looking at their products online just last night. I think I'll have a closer look.
Cheers
152bobby said:
Thanks for that and the mous info, funny, I was looking at their products online just last night. I think I'll have a closer look.
Cheers
Click to expand...
Click to collapse
Actually, just one other question, does the Mous cases work perfectly with the Pixel stand ? If I go down the Mous route, I have to do my research thoroughly, because a case and a car qi charging pad is not cheap !!
I would imagine there would be no magnetic attachment compatibility if the phone attaches to the Pixel Stand magnetically, but, as far as wireless charging, to the best of my knowledge it does not interfere with any other wireless charging devices.
I have two Anker wireless chargers, one pad and one stand, and I haven't had any trouble with either one.
Is there a preferred cigar/cigarette adapter to use with the Mous wireless chargers . If I'm going to cough up this amount of money to accompany a already expensive phone purchase, why skimp on the adapter
They supply a USB-C lighter port adapter as well as a braided USB-C cable with the charger mount, but I also have an Anker port adapter with USB-C and USB-A and it works as well.
Also, just for good measure, I thought I'd also attach a front and rear photo from my mount, to give you an idea of what it would look like.
Just remember, as per my post in the other thread, if you don't want to use the supplied vent clip, which I advise against as it's not very secure, you'll need a mount from another device with a 17mm ball joint. I previously had an iOttie One Touch CD slot mount and it worked perfectly.
Excellent information, much appreciated, thanks. I'll update you with my progress.
152bobby said:
Excellent information, much appreciated, thanks. I'll update you with my progress.
Click to expand...
Click to collapse
Thanks. I have placed my order for the P5 case and the vent mount adapter (my intentions is to try the vent mount, if no good, I'm sure I can detach the mount part at the rear and attached it to my car dash with double sided tape). I did manage to contact Mous and they kindly gave me a 20% code for my first order
152bobby said:
Thanks. I have placed my order for the P5 case and the vent mount adapter (my intentions is to try the vent mount, if no good, I'm sure I can detach the mount part at the rear and attached it to my car dash with double sided tape). I did manage to contact Mous and they kindly gave me a 20% code for my first order
Click to expand...
Click to collapse
If the tape method doesn't work, some of these options might. Just make sure the ball is 17mm. They all seem to be around $10, so not terrible, and cheaper than buying an entirely separate mounting system just for the ball joint.
Thanks, I've been looking at these, should I need one. However, I don't see these with the part that would go on the rear of the Mous charging pad for the ball part to click in to ?
152bobby said:
Thanks, I've been looking at these, should I need one. However, I don't see these with the part that would go on the rear of the Mous charging pad for the ball part to click in to ?
Click to expand...
Click to collapse
The ball cup and threaded nut are on the back of the charging pad.
Of course it is, I've just looked at the Mous air vent mount....I knew I shouldn't have had another beer !
Thanks, I'll see how it goes when it arrives.
152bobby said:
Of course it is, I've just looked at the Mous air vent mount....I knew I shouldn't have had another beer !
Thanks, I'll see how it goes when it arrives.
Click to expand...
Click to collapse
My Mous items arrived today. The case fits nicely, the car air vent actually works well in my car, but I can see it pulling off the vent eventually when removing the phone, but it's not where I want my phone. So I have ordered a 17mm ball joint from Amazon, so I can have it exactly where I want my phone to sit in the car. I've tested the wireless charging and magnetic strength and all is good. I have also tested the wireless charging on my two Pixel stands and my Anker stand also and they all charge fine through the case. So all good for a while . Looking at the case in more detail and feeling it, I have high confidence in this case protecting my phone should I drop it. Thanks for the help I've had in making a decision for this purchase.
**UPDATE**
So I have had both the car wireless charger and the Mous case for my P5 for nearly a week now and I have come across a charging issue. I emailed Mous customer support about it and got a reply today, which to be honest, does not really help me and I think they almost admit that the Mous products are not all they are cracked up to be. They refer to iphone (which certainly does not help me).They have offered a full refund, but I am going to do some more testing myself, as I have a 2 hour drive to do tomorrow and I "think" the issue I am having is to do with me using Android Auto (Google Maps) wirelessly in the car whilst charging, I'm not exactly sure yet, but I am not replying to them until I have done this final test. I am going to use wireless Google Maps for half of my journey with the P5 on the charger and the other half with the phone just sitting on the charger charging with no Google Maps on.I have copied and pasted their reply below, my original message to them, is at the end of their reply, so read this first before reading their reply and possibly give me your thoughts ?
Hi Bobby,
Thanks for reaching out to us and I’m so sorry to hear that you’ve had some issues with your Wireless Charger.
I've had a word with our tech wizards, and they have suggested that you please see possible troubleshooting advice for your phone not charging correctly below:
1. For Apple users: Apple is frequently updating their firmware, which affects the wireless charging system. Therefore some of Apple's own updates could make wireless charging worse or better while they are tuning the software.
2. Wireless charging works by transmitting power from one coil of wire to another, however, the alignment of these coils is very important to transmit the power efficiently. Please make sure that your phone (even without a case) is positioned correctly and centrally, as this will improve charging time and efficiency.
3. Please ensure the voltage is set to the highest possible output to ensure your charger has the best chance of functioning through our case. Some wireless chargers will not have enough power to transmit power to the phone with a case on so make sure you are using a wireless charger that has power from the mains or uses a high-quality USB adaptor supplying more than 1.2 Amps.
4. We will soon be launching Mous wireless charging accessories which are designed to work seamlessly with our cases and will perfectly auto-align the receiver and transmitter coils in the phone and charger.
However, I can appreciate that this is not relevant for everyone, so you are welcome to return your Car Mount if you still wish.
We look forward to hearing from you.
Best regards,
Richard
Customer Experience Advisor
Mous Products Ltd.
On Mon, 24 May at 1:28 AM , Bobby McLeish
Click to expand...
Click to collapse
wrote:
Hello, I have only had my Mous items for a few days. I think there is a issue with my charging pad. It seems to only charge my phone for about 5% and then stops, if I leave the phone attached to the charging pad, it starts to charge again after about 10 minutes and then repeats this. The charging pad itself is quite hot, I think the charging pad is turning itself off when it gets too hot, so I suspect the charging pad is faulty ? I am using the official Mous Pixel 5 case and also the cable and car charger plug which came with the charger. I have ensured that there is no hot air coming from the cars air vent (it is completely off). I think this needs to be replaced, can you get back to me on what to do about this ? Thanks, Bobby.
Click to expand...
Click to collapse
152bobby said:
**UPDATE**
So I have had both the car wireless charger and the Mous case for my P5 for nearly a week now and I have come across a charging issue. I emailed Mous customer support about it and got a reply today, which to be honest, does not really help me and I think they almost admit that the Mous products are not all they are cracked up to be. They refer to iphone (which certainly does not help me).They have offered a full refund, but I am going to do some more testing myself, as I have a 2 hour drive to do tomorrow and I "think" the issue I am having is to do with me using Android Auto (Google Maps) wirelessly in the car whilst charging, I'm not exactly sure yet, but I am not replying to them until I have done this final test. I am going to use wireless Google Maps for half of my journey with the P5 on the charger and the other half with the phone just sitting on the charger charging with no Google Maps on.I have copied and pasted their reply below, my original message to them, is at the end of their reply, so read this first before reading their reply and possibly give me your thoughts ?
Hi Bobby,
Thanks for reaching out to us and I’m so sorry to hear that you’ve had some issues with your Wireless Charger.
I've had a word with our tech wizards, and they have suggested that you please see possible troubleshooting advice for your phone not charging correctly below:
1. For Apple users: Apple is frequently updating their firmware, which affects the wireless charging system. Therefore some of Apple's own updates could make wireless charging worse or better while they are tuning the software.
2. Wireless charging works by transmitting power from one coil of wire to another, however, the alignment of these coils is very important to transmit the power efficiently. Please make sure that your phone (even without a case) is positioned correctly and centrally, as this will improve charging time and efficiency.
3. Please ensure the voltage is set to the highest possible output to ensure your charger has the best chance of functioning through our case. Some wireless chargers will not have enough power to transmit power to the phone with a case on so make sure you are using a wireless charger that has power from the mains or uses a high-quality USB adaptor supplying more than 1.2 Amps.
4. We will soon be launching Mous wireless charging accessories which are designed to work seamlessly with our cases and will perfectly auto-align the receiver and transmitter coils in the phone and charger.
However, I can appreciate that this is not relevant for everyone, so you are welcome to return your Car Mount if you still wish.
We look forward to hearing from you.
Best regards,
Richard
Customer Experience Advisor
Mous Products Ltd.
Click to expand...
Click to collapse
Is it a slow charging issue? One thing I've noticed with wireless car chargers is that, even when they are getting full power, they can't keep up with the power drain from using maps and other apps. I can't say if this applies to iPhone as well, since my last iPhone was the 4s, and I only have experience with the wireless on the Pixel 5, but whenever I run Google Maps and listen to Spotify at the same time, the power draw and charging hit a sort of break-even.
The Mous charger is a little bit better since it uses USB-C, but my previous charger that used Micro-USB couldn't keep up. I also think heat plays a role in it as well. Hot, sunny days on the dashboard seem to keep the phone hot. Add that to the heat produced from the wireless charging and you've got a recipe for faster battery drain. That's just speculation, though, so don't quote me on that.
All that said, I have noticed it stopped charging a couple times recently on particularly hot days, but once I got moving and the AC had time to cool the inside temperature down it started charging again. I also have both of the vents on the left and right side of the charger aimed directly at the mount to help get more airflow around it.
I haven't seen it happen enough to show cause for concern, but if yours is cutting out that often then it may actually be faulty. If you haven't already, try a different USB-C car adapter. If it does the same thing, take it inside your home and plug it into a USB-C wall charger. My guess is, if it's not a faulty pad, that it's either a car adapter or heat issue, and trying those two things will eliminate one or the other, or maybe both. Finally, just for good measure, if it's still an issue, try a different USB-C cable. Sometimes it's just that simple.
Just a sidebar, if you use Discord on your phone, consider closing it when not in use. I've noticed since their latest update that it burns through my battery to the tune of about 20%/hr when I'm on 5g.
I've been researching this one. It has a heafty price but, reviews have been majorally positive.
I have the Mous Limitless 3.0 case and the wireless charging vent mount with my pixel 5. Had them for about 4 months. The case and mount work very good. Magnets are strong. I've never had the phone fall while driving and it charges at 15w reliably for me. Both vertically and horizontally. I think it's important that you use the included cable and cigarette lighter adapter.
I have an Anker Qi desktop charger and it charges at 15w through the Mous case. Not magnetic, though.
Downside for the Mous is the whopping price tag. I also think the case is a bit bulky but I'm used to it now.