Related
I'm curious if there is a stiffer/stronger silicone case out there. I had a hard silicone case for my ipod touch and miss it. The htc silicone case is just to flimsy and I'm not wanting a hard case never had any luck with them
Sent from my EVO using Tapatalk
What you want is a TPU case. It's a different material than silicon, somewhat stiffer and tighter fitting (maybe a bit less shock absorbent?), but pretty much superior in every respect imo... It's still a soft case tho, you still stretch it around the EVO to fit it in and whatnot, and you could bend it if you wanted (only difference is it snaps back to it's original shape much quicker than silicon).
It seems to have more grip on your hand but it slides out of your pocket a lot easier, a LOT easier, and unlike silicon cases it attracts almost no dust and lint whatsoever! My HTC/OEM silicon case (bought at the Sprint store) attracted so much lint and crap in my pocket that within a day of cleaning it all up I'd have this crusty line of crap all around the edges, it was pretty irritating. None of that w/my TPU case, at all!
The TPU cases also feel a lot slimmer on your hand even tho they're not that much thinner than the silicon one, they're still thick enough so that the camera is recessed below it and fully protected (most of them are anyway, there's some thinner ones)... I guess part of the reason they feel more svelte is that the edges are more rounded off and not as squre-ish as the HTC silicon one.
Button press feel is also much better w/these, probably because of the tighter fit, they actually improve the handling of the power button if you ask me. The side edges of these cases don't move at all unless you pull on it tightly, totally different feel compared to the silicon ones which loosen up and from just swiping your finger across the screen you can end up stretching the edge out.
In short, they're just superior in every way, just get one and you'll thank me later. All you have to do is choose one of the different ones out there based on aesthetics...
Amzer sells one w/an Argyle pattern on the back, that's what I've got right now, it's available on Amazon and off Amzer's site for around the same price ($9-10), it's semi-translucent and the pattern is actually a lot more subdued and doesn't stand out nearly as much as you'd think from looking at the online pics. I actually like the pattern, if anything I'd say the shade of the skin isn't quite smoked/black, it has a slight hint of amber/brown...
That's the only thing that bothers me about it. I'm gonna be ordering a plain black one along w/a red one from DCMugen on Ebay, he's selling some made by Epik that look to be the exact same thing w/o the Argyle pattern, and they're cheaper to boot ($3.50, or $6.50 for two). I can get you a link if you can't find 'em... I think they have 'em in blue and clear and a few other colors too.
Just don't fall for the cheap off-brand Argyle ones on Ebay, you can tell them apart easily because unlike the two I've mentioned those have one large cutout for the camera/LED/speaker, whereas these other ones have individual cutouts and from what I've read they're a bit thicker. Those other Ebay ones also have a large silly cutout for the fingernail hole on the battery lid that you use to pry it off, seems like a goof on the mold/design.
If you don't care for the Argyle pattern on the Amzer one I'd get the Epik ones from DCMugen, I think the colors/tint on those are closer to the photos. Here's a link to the red one, you can click on the seller for the other colors and the package pricing for two or whatever.
If you're not into the translucent look of either of those TPU cases you can always grab the matte black one at www.evocases.net There's a thread for those right here at XDA where misticjeff has even thrown in a $1 code discount for XDA members. The sides/front are still glossy (perhaps a bit glossier than the translucent ones, judging by the photos), back's matte. The frost one is no longer available.
On the thread about those some people were complaining about the feel of the power button, seems it's not as great as the Amzer/Epik ones, some people resorted to sticking a lil' bit of tape in between to make it easier to press... One thing the evocases.net does have going for it is the slightly raised ring around the camera, which I guess might protect it more in the long run... Even tho they're all thick enough that the lens is recessed (as well as the screen obviously).
My 2 cents, hope it helps... I'm loving the feel of these TPU cases tho, I'll probably never get a silicon case for a phone again.
Whew, that second post got pretty long... A picture or two would've made it easier to explain I guess. Lemme know if you're interested in the Argyle one and I can grab my camera and post some pics of how it really looks, there doesn't seem to be many pictures out there of the actual case ON the phone (for either of them really).
I was gonna wait 'till I had the Epik ones so I could photograph them all side by side but I can take pics of the Amzer Argyle one in advance and post 'em up. Like I said, I actually dig the Argyle pattern because it's pretty subdued, it's more of an etch or a shade (it actually feels like an etch on the inside of the case), rather than a print. The only thing that bothers me about it is the overall shade/tint.
I probably wouldn't even be ordering the Epik one if I wasn't also ordering some of those clear battery doors that are about to go on sale... I think those plain Epik cases w/the clear battery door will look very slick.
Best buy might have what you are looking for. My only gripe is the buttons feel hard to push. But give it a shot (most BB will let you try on the case) it might be what you are looking for.
Seidio Innocase Active Cased - Limited Edition
After looking around the net for some time I bought the Seido Innocase Active Limited Edition.
Can't post a link but search Amazon for the title in my thread.
It's a semi-hard silicon cover with a siliconized hard plastic that exo-skeleton. Perfect combo in my opinion. My one complaint is that the edges on the hard plastic piece have the siliconized coating peeling off a little but I think I may have gotten a defective unit as I haven't seen anyone else complaining about it yet.
Also got the ClearTouch screen cover anti-glare version. I've had this cover on a few phones and it's also the best for reducing glare and fingerprints while maintaining clarity. Kinda hard to install without getting dust underneath but once you get it on right it looks and feels great. ClearTouch is sold by boxwave and is on Amazon.
Hybrid Flexi Skin Cover
Has anyone tried the Hybrid Flexi Skin cover from Daydeal.com? I'm also looking for a tighter case than my OEM silicone skin I got from Sprint. I just don't like the way the sides become flimsy and flaps off the phone when I swipe my screen. I'm looking at this case:
Hybrid Flexi Skin Cover for HTC EVO 4G, Honeycomb (Smoke & Clear)
Hybrid Flexi Skin Cover for HTC EVO 4G is a combination back cover consisting of a semi-hard, semi-soft Thermoplastic Polyurethane (TPU) edge with a smooth hard back.
* Protects the side edges and back of your EVO 4G
* Hybrid cover consisting of a semi-hard, semi-soft TPU edge and a smooth hard back
* Stylish glossy TPU edge provides shock-absorbing protection
* Lightweight TPU is resistant to taring, stretching and deforming
* Compatible with HTC EVO 4G
Sorry, I'm a newbie and can't post links, yet. I don't know if the TPU edges would solve the flapping problem, since it's supposed to be firmer & tighter. Any input would be appreciated. Thanks.
Hiway said:
Has anyone tried the Hybrid Flexi Skin cover from Daydeal.com? I'm also looking for a tighter case than my OEM silicone skin I got from Sprint. I just don't like the way the sides become flimsy and flaps off the phone when I swipe my screen. I'm looking at this case:
Hybrid Flexi Skin Cover for HTC EVO 4G, Honeycomb (Smoke & Clear)
Hybrid Flexi Skin Cover for HTC EVO 4G is a combination back cover consisting of a semi-hard, semi-soft Thermoplastic Polyurethane (TPU) edge with a smooth hard back.
...
Sorry, I'm a newbie and can't post links, yet. I don't know if the TPU edges would solve the flapping problem, since it's supposed to be firmer & tighter. Any input would be appreciated. Thanks.
Click to expand...
Click to collapse
As I said in my previous post, TPU rocks as a material for cases/skins... I don't blame ya for skipping right over it tho.
TPU >>>>>> silicon
TPU doesn't attract dust at all, it's much tighter/rigid so the side edges don't flop out at all, but it's still got plenty of give (so it'll absorb a fall/bump), you could bend 'em in half if you wanted... Only difference is it'll snap back into form in a second unlike silicon which will probably just bounce around in an arc.
TPU also seems just as grippy on your hand, if not more so, but it slides in and out of pockets way way easier, and most of the TPU cases I've seen feel way more svelte in the hand than the OEM/HTC silicon scene... Probably in part because they're a tad thinner, probably also because the edges are more rounded off and not as blocky. Physically I'm sure it isn't a huge difference, but it sure feels like it.
This thread has some further discussion on TPU cases, it's really hard to judge them based on pictures alone, I was very pleasantly surprised with mine.
So I tried googling the title you posted and came up with this, only place I could find it at. Looks pretty interesting, seems the back is hard plastic and the edges are TPU. If you dig that honeycomb pattern I'd say go for it...
Altho if it's actual plastic it might get scratched up over time Looks like it's also clear/translucent, clear plastic usually shows every single flaw... A plain TPU case wouldn't have that issue. I'm just not seeing the advantage over 100% TPU, which are also like $3.50 vs $14 (look for DCMugen's Epik/TPU cases on Ebay).
OTOH that red back + black edges on the video in the link I pasted before looks pretty sweet... The rest look kinda gaudy imo ('cept for the all black) but red/black looks really different, I like it.
P.S. This is the Honeycomb (Smoke & Red) combination I was alluding to... There's also Honeycomb (Smoke & Smoke) and plain Black & Smoke (no honeycomb pattern, solid black sides). The red is the most distinct imo, those are all probably better in the long run than the clear back (less forgiving).
Jayr00 said:
Kinda hard to install without getting dust underneath but once you get it on right it looks and feels great. ClearTouch is sold by boxwave and is on Amazon.
Click to expand...
Click to collapse
Tip for the next time you gotta install a screen protector and its the hard type: get some scotch tape, put it on the non adhesive side of the screen protector so you can peel it back without touching anything, and then grab another piece of tape and start taping the dust out of the screen or adhesive side of the protector and you'll be dust free in no time. Friends came over cuz they all needed new protectors and i did 4 phones in 20 minutes.
Hybrid Flexi Case
I got my new case today....went with the Smoke & Smoke combo. This case is awesome, I HIGHLY recommend it. the sides don't flap and it has a really tight fit and seems really durable. Got it off of EBay for about $8.50 ($4.50 for case + $4.00 shipping/handling) from Daydeal as opposed to going to their site and paying $13.99.
Impulses said:
P.S. This is the Honeycomb (Smoke & Red) combination I was alluding to... There's also Honeycomb (Smoke & Smoke) and plain Black & Smoke (no honeycomb pattern, solid black sides). The red is the most distinct imo, those are all probably better in the long run than the clear back (less forgiving).
Click to expand...
Click to collapse
I went with the smoke on smoke honeycomb case and got it today. It's darker so I think it'll hide any scratching that my occur on the backing. I agree with you on the clear backs when I first saw them, but the back seems scratch resistant (only time will tell)
Hiway said:
I got my new case today....went with the Smoke & Smoke combo. This case is awesome, I HIGHLY recommend it. the sides don't flap and it has a really tight fit and seems really durable. Got it off of EBay for about $8.50 ($4.50 for case + $4.00 shipping/handling) from Daydeal as opposed to going to their site and paying $13.99.
Click to expand...
Click to collapse
If possible can you please post pics? Im interested in this case but have only seen Daydeal's review on it.
OK - I've been using the ATT store Body Glove case since I bought the Captivate, which is ok but I don't really like the stripes on the back, and it is a bit too slippery for me.
I just ordered the Seidio case because it has more of a matte finish and I liked the felt interior. So I don't know if I like it or not.
A few minutes ago I took the phone out of it's case to dust it and clean out the case when I got a call. I was surprised at how slim the phone felt without it's Body Glove case on. I liked it. But I also found it a bit slippery. ( A speaker phone call was put on the arm of the chair I was in - with the case it would hold - without it slid away)
Now I am wondering if I should just use some skateboard tape or something similar on key areas to allow me to set it down and hold it comfortably (where it won't slip) instead of using a case. I don't use a screen protector and I don't think this phone needs it.
Any comments or suggestions?
Now that I've thought about it for a few minutes - I think what I want is a rubberized battery cover. That would be the bomb.
I don't use a case on mine and I've yet to get a single scratch on the front or back - the glass is very tough. I cringe at having to use a case, losing accuracy, clarity, and brightness on the screen and having to touch through that...having it hard to slip in and out of my pocket...not looking as nice. It's like if your wife made you use a condom every time.
just "paint" it with some Elmer's Rubber Cement. Im really kidding but I'm with you I like the feel of the phone and I hate the rubber case I got it makes it a pain to get in and out of the pocket. Personally I plan on selling this phone in a couple of months so I want it in good condition.
vsboxerboy1 said:
I don't use a case on mine and I've yet to get a single scratch on the front or back - the glass is very tough. I cringe at having to use a case, losing accuracy, clarity, and brightness on the screen and having to touch through that...having it hard to slip in and out of my pocket...not looking as nice. It's like if your wife made you use a condom every time.
Click to expand...
Click to collapse
Agreed that the screen is fine on its own. But I still think the back needs some help.
Also, I do not like condoms. Neither do my wife and kids.
Ah, well I saw something a while back where someone basically took four little rubber/plastic stickers and put one on each corner of the back of the phone to lift the back up off whatever surface you set it on just a hair. I would imagine that you'd get good traction with that too - I can't seem to find the exact application of it though......
This thread is mostly me think out loud.
I believe that what I want is a rubberized battery cover.
The cover is slightly recessed - it is lower then the bottom locking section and the top section with the camera. It also wraps around the sides almost 1/2 of the way.
I think that if the battery cover were coated with a rubberized, non-slip material, it would be better. If the rubberization made the cover stick out slightly, rather than be recessed, it would allow the phone to be set on it's back and not slide away and keep the camera off the deck. Also, the wrap around side parts of the cover would help when holding the phone.
Now, can someone tell me of a place/process that might do this? (Not rubber cement but close) My pickup has a Rhino Lining coating that I love. There is a place nearby that does that work but the coating is like 1/8-1/4 inches and that is a bit to thick for the phone.
Any Ideas?
http://www.plastidip.com/home_solutions/Plasti_Dip
http://www.brownells.com/.aspx/pid=1150/Product/GUN_KOTE_trade__OVEN_CURE__GUN_FINISH
http://www.goboatingamerica.com/products/DM_article.asp?id=3645
Found these
Bought this stuff at Home Depot.
Then tested in on this beer can. I didn't clean or prep the can, just picked it up off of the floor.
This is 5 coats. It is still thin. Dries fast and feels just about how I'd like it to. Not tacky - sort of a hard rubber feel. It is flexible, the can bends and the stuff stays with it.
It can be scratched, you may be able to see a scratch I made with my nail. It didn't go all the way through to the can though - and I had to scratch hard. It looks like it would be easy to spray another coat over any scuffs.
I plan to do the back of the battery cover - thick enough to make it a bit taller than the top and bottom sections of the phone. The way it is going it seem like that may take 15+ coats. I'll keep testing.
Two things about that though, the battery cover is used not only as the speaker output but the battery cover itself also dissipates a good amount of the heat that the phone generates. You probably want to be a more careful than usual in designing something that is going to smother this part of the phone.
not sure how much you're looking to spend but I put the Zagg total protection on mine. You get full protection on your phone but you can't see it, so you still get the sleek look and it's still very thin as well. The clear plastic is also great for gripping, I can set it on the dash of my car and drive normally and it won't budge.
I've had good luck with bestskinsever.com
Used it on my Nexus One and the fit was good, buddy got one for his vibrant and the fit is good as well.
journeyman82 said:
not sure how much you're looking to spend but I put the Zagg total protection on mine. You get full protection on your phone but you can't see it, so you still get the sleek look and it's still very thin as well. The clear plastic is also great for gripping, I can set it on the dash of my car and drive normally and it won't budge.
Click to expand...
Click to collapse
Looks interesting. I wish they had the leather skin for the captivate. I would be all over that. In fact I may need to take a trip to the fabric store to see what they have.
Thanks.
Ok to finish up my saga...
I liked the faux leather on the cover mentioned in the post above so I went to the fabric store and ended up with some black, I believe they call it marbled vinyl. It looked and felt similar to the back of a blackberry I once held.
I tested it on my trusty Busch Light can with some 3M spray adhesive and it seemed to hold fairly well.
So I went for it. I taped off the inside and the prongs of the battery cover. Sprayed glue on the cover and the back of a piece of vinyl cut too big. Stuck it on and smoothed it out. I sat the cover on a bag of rice and and put a bag of brown sugar on top (to push around the curves) and topped it off with a gallon jug of tile grout.
Waited an hour, probably longer than needed, and used a pointy x-acto knife to trim off the excess. I had also put a piece of tape over the speaker holes so I cut that back open to. The underside of the vinyl has a white background so once it was trimmed to fit I went around the edges with a fine tipped sharpie, which blended well.
Overall I like it. It is just a bit thinker that the top and bottom bands, so if you lay her on her back those parts don't touch a flat table. It has a leathery, grippy feel without being tacky, which is what I was going for. I do already miss the front edge lip that the Body Golve provided but it is also almost it;s original thickness.
Pics below. (Sorry about the crappy last pic. I had the phone with new back all set up on a white surface, ready for it's glamor shot, when I realized that the phone is my camera)
Staplebox: great job!
Wow that is a nice, careful job.....
staplebox said:
Ok to finish up my saga...
I liked the faux leather on the cover mentioned in the post above so I went to the fabric store and ended up with some black, I believe they call it marbled vinyl. It looked and felt similar to the back of a blackberry I once held.
I tested it on my trusty Busch Light can with some 3M spray adhesive and it seemed to hold fairly well.
So I went for it. I taped off the inside and the prongs of the battery cover. Sprayed glue on the cover and the back of a piece of vinyl cut too big. Stuck it on and smoothed it out. I sat the cover on a bag of rice and and put a bag of brown sugar on top (to push around the curves) and topped it off with a gallon jug of tile grout.
Waited an hour, probably longer than needed, and used a pointy x-acto knife to trim off the excess. I had also put a piece of tape over the speaker holes so I cut that back open to. The underside of the vinyl has a white background so once it was trimmed to fit I went around the edges with a fine tipped sharpie, which blended well.
Overall I like it. It is just a bit thinker that the top and bottom bands, so if you lay her on her back those parts don't touch a flat table. It has a leathery, grippy feel without being tacky, which is what I was going for. I do already miss the front edge lip that the Body Golve provided but it is also almost it;s original thickness.
Pics below. (Sorry about the crappy last pic. I had the phone with new back all set up on a white surface, ready for it's glamor shot, when I realized that the phone is my camera)
Click to expand...
Click to collapse
love it, im stealing that!
Go for it. Usually I prefer to buy a second of whatever I am defacing before I deface it but I didn't find any battery covers online. I also didn't look to hard.
It is still on and I still like it. The only thing I don't like too much are the sides. I completely covered the back, right up to the side edges. It is a perfect thickness on the back but feels too thick on the sides. I wish I could have found a thinner material that I could have built up on the back and tapered to one layer on the sides. I really wanted grippyness on the sides so, oh well, it's good enough.
I'm still on the look out for a better spray on rubber. I'll update if I find anything good.
Hopefully someone will start making aftermarket battery covers with some options.
Thanks and good luck,.
Second the stealing. Awesome idea and writeup. Thanks for sharing.
From a phone on an app
I scrapped the vinyl. The edges were just bugging me to much. I still think a thinner material would work well though.
I cleaned up the cover - looked fine again with all the glue off of it.
I went back to the rubber spray. I've got about 8 coats on in the attached pic. Need to wait about 30 min in between coats. I'll keep going until I go to sleep, let it dry overnight - and test it out tomorrow.
ETA - put it on the phone the today. Love it. Doesn't add any bulk and provides a grippyness to the back and sides. I'll find out how durable it is.
When i bought my HTC One Stealth Black, i made sure that i got a perfect model (no defects). I took about an hour in the shop examining all the black HTC One's (they agreed to open 3 boxes for me) before i finally made up my mind. I paid for my phone off-contract and went home perfectly happy with a 801e model (it also has a sticker on the side of the phone that says UKR and on the box as well, so i guess it's from Ukraine and i got a 3-pin power adapter in the box together with the standard 2-pin charger plug) and also got a free TPU case with screen protector, as gift from the shop. Well, i put my phone in the TPU case as soon as i got home for fear of any drops/bumps/scratches, put it in my jeans pocket and went through the rest of my day moving around. Later that afternoon, i pulled the phone out of its case to touch the cold aluminium back and to my horror, i found a scratch (there were no scratches whatsoever before) that matched the contour of the TPU case around the camera. The scratch is around the flash.
Conclusion: The cheap unbranded TPU case seemed to fit the phone snugly but apparently not, as the constant movement and rubbing of the phone within the TPU case from inside my jeans pocket had caused the sharp edge of the TPU case to slowly erode the paint coating. It's a good thing that i noticed it after only one day usage or the etching would have definitely gone deeper, possibly even exposing the aluminium colour after a couple of days. It says "nothing but the best" on the packaging of the unbranded case, which is ironic.
So, my advice (and the reason for my endless rant in this post): stay away from cheap TPU cases, even if it says TPU, which might be true about the material itself but the fact of the matter - without a tight fit of the phone inside the casing, the resulting inside friction between the phone and its casing will damage your phone, causing the paint to wear off. This is probably not applicable to those of you who chose/use the Glacial Silver HTC One, since any scratch will probably not show up. But with time, the constant friction might cause the scratch to become visible. I've attached pictures so you can understand why i'm *****ing about my One By the way, i apologize for my dirty camera lens.
Lesson learnt - i've already ordered 3 casings (the best i could find after hours of searching, for cases that offer a balance between compactness v/s protection); Cimo Grip Back Case Flexible TPU Black, Otterbox Commuter Black and UAG Aero. I wouldn't bother with any other cases, unless you want even more protection, then you should be satisfied with the Otterbox Defender case.
My friend .. ANY case you put on the phone has the potential to scratch the aluminum on the edges. It is simple physics: if you get some dust/sand in between the case and the aluminum (where in other locations can the dust/sand/lint settle ?) any slight pressure or movement of the case will cause a small surface defect. You can not hide from that and you can not prevent that.
Live with it ! It is called reality.
electronical said:
When i bought my HTC One Stealth Black, i made sure that i got a perfect model (no defects). I took about an hour in the shop examining all the black HTC One's (they agreed to open 3 boxes for me) before i finally made up my mind. I paid for my phone off-contract and went home perfectly happy with a 801e model (it also has a sticker on the side of the phone that says UKR and on the box as well, so i guess it's from Ukraine and i got a 3-pin power adapter in the box together with the standard 2-pin charger plug) and also got a free TPU case with screen protector, as gift from the shop. Well, i put my phone in the TPU case as soon as i got home for fear of any drops/bumps/scratches, put it in my jeans pocket and went through the rest of my day moving around. Later that afternoon, i pulled the phone out of its case to touch the cold aluminium back and to my horror, i found a scratch (there were no scratches whatsoever before) that matched the contour of the TPU case around the camera. The scratch is around the flash.
Conclusion: The cheap unbranded TPU case seemed to fit the phone snugly but apparently not, as the constant movement and rubbing of the phone within the TPU case from inside my jeans pocket had caused the sharp edge of the TPU case to slowly erode the paint coating. It's a good thing that i noticed it after only one day usage or the etching would have definitely gone deeper, possibly even exposing the aluminium colour after a couple of days. It says "nothing but the best" on the packaging of the unbranded case, which is ironic.
So, my advice (and the reason for my endless rant in this post): stay away from cheap TPU cases, even if it says TPU, which might be true about the material itself but the fact of the matter - without a tight fit of the phone inside the casing, the resulting inside friction between the phone and its casing will damage your phone, causing the paint to wear off. This is probably not applicable to those of you who chose/use the Glacial Silver HTC One, since any scratch will probably not show up. But with time, the constant friction might cause the scratch to become visible. I've attached pictures so you can understand why i'm *****ing about my One By the way, i apologize for my dirty camera lens.
Lesson learnt - i've already ordered 3 casings (the best i could find after hours of searching, for cases that offer a balance between compactness v/s protection); Cimo Grip Back Case Flexible TPU Black, Otterbox Commuter Black and UAG Aero. I wouldn't bother with any other cases, unless you want even more protection, then you should be satisfied with the Otterbox Defender case.
Click to expand...
Click to collapse
I had the black for a while. I think that it is prone to anything. Apart from light scratches sustained by using the double dip case, the camera cut out of an incipio case left a watermark on it as well. Now using a silver one and not a single scratch. Rotating between three cases.
Forgive me if I'm wrong, but isn't anodized AL WAY harder than TPU?
If it is, then isn't it PHYSICALLY IMPOSSIBLE for the case itself to scratch the phone?
Either a) there was dust/dirt in the case or
b) it's not a scratch, try wiping it with mild soap, water and a soft cloth.
Interesting thread...you were writing this 3 years ago, I just picked up two pristine condition used m7s, both with nearly all day batteries. Yesterday I got two cases of the first type described below.
I just love these phones so much. They are such a huge upgrade from any phone I have had since I had a droid 2 from motorola before knowing anything at all about these nifty little computers.
I just came in here to say that I will be getting the hard glass protection from now on for every phone I get. Would also recommend to anyone as it is far superior to foils.
Also three good types of cases:
- the hardened shell with no button coverage, and brushed metal exterior
- the clear plastic back, black bumpered semi hard with plugs and accurately designed button enhancers (distinguished by black surface lines on the back coming in from upper and lower edges about a cm each, towards the antennas)
-and believe it or not I really liked the ordinary rubber sort of cases with wavy line down the back and dual texture... as long as they have button covers. But those wouldnt be good for people who have a hard time with the buttons already.
Just picking up these phones starting in June 2016...has made my android experience so much more enjoyable...now being able to play top 3d heavy performance requiring games...and so much different development for the phones.
here's a couple pics of my phone cases I was describing. no scratches whatsoever on the two used like new phones, although its a used case on goldy. the other phones are for family and such, but also loving the cases on them. red looks good in red but it obscures the back... so take clear
kruc Ire said:
here's a couple pics of my phone cases I was describing. no scratches whatsoever on the two used like new phones, although its a used case on goldy. the other phones are for family and such, but also loving the cases on them. red looks good in red but it obscures the back... so take clear
Click to expand...
Click to collapse
Link please?
Saf98 said:
Link please?
Click to expand...
Click to collapse
www.urbandictionary.com/define.php?term=spinner
Rearth Discover Wallet Case Review
Im a little surprised that no one has done a review of this product for the Nexus 5 yet but its hard to plop down a good chunk of change for a phone case especially if the point of getting said phone was because it is a bargain. I usually don't buy cases which cover the phone completely with a flap (wallet style) but I really love my Nexus 5 and this case looked like the best I could find and at around 50 bucks I hoped for the best...
The Box
Sorry no pictures of this because I opened it in an unboxing video and didn't think to take pictures of it. The box was very flimsy, almost looked as if it was damaged. The plastic window showcasing the phone had been pushed in creating a hole which you could stick your fingers into. That didn't really bother me much as long as the contents weren't damaged.
There were a few items in the box:
-The case
-Little card explaining the features of the case
-Screen protector and screen protector accessories (I didnt use any of these because I have a Spigen screen protector on my Nexus 5 already)
The case was held in place inside the box by a thin piece of cardboard with a weird paper strap which had adhesive on the very and which was stuck to the phone case. Peeling off the piece of paper with adhesive on it left a mark which I first thought was just stuck adhesive (Turns out this actually damaged the leather leaving marks)
The Case
The case felt very nice to the touch as it is real leather, It made my phone look like a little book. This case obviously adds a lot of bulk but its meant to replace your wallet in addition to protecting your phone.
Front of the case
Back of the case, notice the damage to the leather? Cutouts are fine with the exception of a little piece of plastic left over from the molding process with by the camera hole at 11 o'clock.
Great stitching and some branding.
Branding on the rib.
Inside the case, four pockets, some subtle branding.
How the phone is held in, some branding, Ringke Fusion case with a leather cover. All holes are nicely cut out and all buttons are covered and responsive.
The Conclusion
In conclusion it's a flawed beauty, it is so close to being perfect for me. I think this is a great start for Rearth, they usually make much cheaper products, but for the cost I don't think the adhesive should've left a mark like that (I feel its not acceptable), I think they should at least remove the "Ringke Fusion" on the case and it's missing one key feature that turns me off, there is no wake function for this case.
I will be contacting Rearth to see if I can get a replacement or if they will be updating this case at least with a sleep wake function.
Thanks for reading/watching guys!
Alright, after months of trying to nail this problem down I finally have a good solution!
I've tried a few different cases on my fold3 and none of them really held well on the top screen when folded and in my pocket. It would start sliding off. So I finally have a solution. Get yourself some good double sided tape (I suggest some type of 3m tape This for example) and measure you a piece of tape that is length of the case that touches the phone that isn't on the screen. Then take a sharp knife and cut a very thin strip of tape. Put that strip on your case and then put the case on the phone. Press hard and hold it there for a bit and then BAM it's not going anywhere again. If it's done right it will not be noticable (see pics I've attached) unless you look closely it's really clean and nice looking to me.
In the pictures you can see the black strip of tape that came with the case that wasn't super useful but what useful was my piece of tape.
I have been lucky in that my cases have not had this issue, but I agree, if you need too, there is no shame in using tape to keep this thing protected.
Just use good quality stuff.
This is the stuff I have and I LOVE IT... https://smile.amazon.com/25Meter-Double-Adhesive-Display-Housing/dp/B071D5CKCX
Good solution, just easy.
Unfortunetly fold series and other folded devices need specially cover.
I have fold 2 1,5 year and few covers:
Ringke slim. Good cover but even pieces of double tape after take off i saw particles of dust and sand.
Next i bought Spigen armor pro. Great protection but a lot of bulky and even mount with force for good fit after few weeks and take off i saw few white dots on the frame from probably few particles sand.
It was little frustrating because I always to take care my devices and carry without any other stuff in my pocket.
4 days ago i told "stop" covers with use tape for hold on the device.
Without case fold is really beautifull and touch metal in every time is really pleasant .
I read topics on reddit about "caseless fold devices" and a lot of people have enjoy use folds without case.
After that I use my device only with original leather back cover, without front cover.
Admittedly 2 days ago drop my fold from pocket on the floor. It drop edge front frame but after that is only scratch and rest device survive well
I have béen using a dab of clear silicone sealant. Holds well, and comes off by rubbing it with a cloth.
After a few months of searching, I just gave up and use whichever is the slimmest case without an adhesive. It made more than a few scratches on the side of my screen and I just decided not to give a crap about it, it doesn't go over the main screen anyway.