I have been up and down all the sites and recovery methods.
ISSUE:
In an attempt to root my Zenfone 2 (2.19.40.22 Lollipop) the tool I was using seemed to get stuck looking for my device. This was after installing a fastboot, or an attempt I believe. After a minute or so I noticed the phone screen was constantly showing the USB Logo.
I can turn on my phone and use it no problem. HOWEVER, I cannot POWER + VOL UP, to enter the bootloader. It just goes back to that USB Logo with the White Bar under it. And I have to power off and ON my phone again to get back to normal operation.
As you can imagine this makes it rather difficult to flash anything or use the ADB Tools whatsoever. Is there anything I can do to get that back, or am I doomed with a phone that can never be rooted?
[The tool that started this whole issue was the TWRPRecovery-Install]
Twrp tool only installs twrp recovery which you need an unlocked boot loader to install, so it should have never been used, can you use adb from the phone in normal operation? Can you get into recovery at all? Sometimes you can boot to recovery from adb shell when phone is in normal boot. Most of the solutions I can think of requires root but if you figure out how to get to recovery you can sideload a full update file to restore everything
Sent from my ASUS_Z00AD using Tapatalk
---------- Post added at 07:40 PM ---------- Previous post was at 07:36 PM ----------
And I am not sure if it will work now, but there is a one click root tool for this phone you could try it, but if you have an unusable bootloader it may not work, let me do some research for other options, may not find anything but we'll see
Sent from my ASUS_Z00AD using Tapatalk
---------- Post added at 07:43 PM ---------- Previous post was at 07:40 PM ----------
Start here
https://www.mediafire.com/folder/w70w7r1a65840/Zenfone_2
Sent from my ASUS_Z00AD using Tapatalk
Thanks for the info. I clearly followed the wrong guide. I did try the One Click Tool but again it goes straight to the USB logo. Its odd, if it was broken or deleted your imagine there would be a way to fix or reinstall it.
JetPKFR said:
Thanks for the info. I clearly followed the wrong guide. I did try the One Click Tool but again it goes straight to the USB logo. Its odd, if it was broken or deleted your imagine there would be a way to fix or reinstall it.
Click to expand...
Click to collapse
That is generally considered bricked... Only ASUS can fix for now....
Related
Hey guys, just a few days ago I messed up my screen and can't even see anything on it. However, the phone itself works, especially since the USB detects it. However, I cannot access the files because of the "locked screen" issue. I am on a Mac running Lion with no access to a PC at this point.
I was wondering if there was anyway to get into the phone's file system without the stupid locked screen issue, since of course I can't do anything on it because it's broken haha.
It was rooted, had clockwork, and ran mmuzzy's jellybean rom.
You can get adb access while booted into a custom recovery. Is your screen totally screwed or can you see when you boot into fastoot / recovery.
3rdstring said:
You can get adb access while booted into a custom recovery. Is your screen totally screwed or can you see when you boot into fastoot / recovery.
Click to expand...
Click to collapse
I can't see anything on it, nor does the touch actually work.
USB debugging on? Do you have adb setup?
3rdstring said:
USB debugging on? Do you have adb setup?
Click to expand...
Click to collapse
USB debugging is in. I have never actually done with ADB so I'm not really sure how to work it. Any insight on that?
http://forum.xda-developers.com/showthread.php?t=1869380
Sent from my Galaxy Nexus using Tapatalk 2
---------- Post added at 11:14 PM ---------- Previous post was at 11:12 PM ----------
http://forum.xda-developers.com/showpost.php?p=25804454&postcount=59
Sent from my Galaxy Nexus using Tapatalk 2
just did the freegee unlock and phone will not power on
what happened?
i even got an popup congratulating me that i was unlocked
What version g pro you have?
Sent from my LG-E980 using Tapatalk 2
att version
e980
Clutchz said:
att version
e980
Click to expand...
Click to collapse
Try posting your issue in the actual thread in original android development
Sent from my LG-E980 using Tapatalk 2
Only your recovery and possibly boot partitions are touched, so worst case you can always get to download mode. However if the phone won't turn on at all its something not directly related. What happened before you rebooted into this state?
Sent from my LG-LS970 using xda app-developers app
i was doing the freegee thing and it had finished i went to home and hit reboot and nothing it stayed there
FreeGee has been updated and I unlocked my phone without any issues.
Clutchz said:
just did the freegee unlock and phone will not power on
what happened?
i even got an popup congratulating me that i was unlocked
Click to expand...
Click to collapse
Mine's doing it too man. Installed the app. Phone is rooted but stock recovery. Let it do its unlock thing and said yes to disable LGE security. Then tried to reboot using the volume and home keys to get to recovery and it gave a "Secure booting failed. Cause: Device Unlocked so boot success!!" message. Then LG logo again then AT&T animation and that's as far as it gets. No recovery menu, no normal boot. Just AT&T.
You get yours figured out yet? We gonna have to LGNPST back to stock?
---------- Post added at 09:50 PM ---------- Previous post was at 09:49 PM ----------
wahida76 said:
FreeGee has been updated and I unlocked my phone without any issues.
Click to expand...
Click to collapse
SO how do you get to recovery then? I tried to 2 button into recovery and am now unable to boot the phone.
the computer detects something by this name: Qualcomm HS-USB QDLoader 9008 (COM17) and the screen stays black on the LG
lessthanzach said:
Mine's doing it too man. Installed the app. Phone is rooted but stock recovery. Let it do its unlock thing and said yes to disable LGE security. Then tried to reboot using the volume and home keys to get to recovery and it gave a "Secure booting failed. Cause: Device Unlocked so boot success!!" message. Then LG logo again then AT&T animation and that's as far as it gets. No recovery menu, no normal boot. Just AT&T.
You get yours figured out yet? We gonna have to LGNPST back to stock?
---------- Post added at 09:50 PM ---------- Previous post was at 09:49 PM ----------
SO how do you get to recovery then? I tried to 2 button into recovery and am now unable to boot the phone.
Click to expand...
Click to collapse
I used a reboot app to boot recovery
---------- Post added at 09:57 PM ---------- Previous post was at 09:56 PM ----------
Clutchz said:
the computer detects something by this name: Qualcomm HS-USB QDLoader 9008 (COM17) and the screen stays black on the LG
Click to expand...
Click to collapse
Your phone hard bricked and flashing might work
wahida76 said:
I used a reboot app to boot recovery
---------- Post added at 09:57 PM ---------- Previous post was at 09:56 PM ----------
Your phone hard bricked and flashing might work
Click to expand...
Click to collapse
the flash tools dont detect the phone
Clutchz said:
the flash tools dont detect the phone
Click to expand...
Click to collapse
I am really sorry to say this but if that is the case then your hard brick can't be fixed your option is warranty.
oh well i'll go to att tomorrow thanks guys
Clutchz said:
oh well i'll go to att tomorrow thanks guys
Click to expand...
Click to collapse
If you bought the phone within the last 14 days then you can return it if not you can call at&t and speak to warranty and they will send you a warranty replacement your other option is to ask if they have a local warranty center they can try to flash it or exchange it.
Clutchz said:
oh well i'll go to att tomorrow thanks guys
Click to expand...
Click to collapse
Are you sure you were putting it into download mode? You take out the battery. Then put battery back in the phone. THen I believe you hold the volume down key and plug the phone into the computer. Then LGNPST should recognize the phone after you change the COM port to I believe 41 or 42
Edit: You hold BOTH volume keys while plugging the phone into the computer. It needs to be completely off when you do this.
Edit 2: Here's the guide : http://forum.xda-developers.com/showthread.php?t=2302660
Switch it under device manager to COM port 41. Now flash tools should recognize it.
I'm honestly bummed that I'm now going to have to re-setup everything again. I just had to flash my phone 2 weeks ago to get rid of 2nd Init recovery to install the value pack. Now I get to do it again, then run the update, then re-root, and put my 200+ apps back on, lol. FML. I guess this just isn't the phone the tinker with. Never had any of these issues on my S1, S2, S3, HTC One, One X, Note, etc. Oh well.
Tried it didn't work thanks for the help anyways guys i have a 90 day no questions asked with Costco so i'll take advantage of that any way to export text and call logs? Too much to ask right?
Clutchz said:
Tried it didn't work thanks for the help anyways guys i have a 90 day no questions asked with Costco so i'll take advantage of that any way to export text and call logs? Too much to ask right?
Click to expand...
Click to collapse
If you're on a windows 8 machine it will not detect your phone with them drivers, you need a win 7 os. I had same issue before
Sent from my LG-E980 using Tapatalk 2
turilo said:
If you're on a windows 8 machine it will not detect your phone with them drivers, you need a win 7 os. I had same issue before
Sent from my LG-E980 using Tapatalk 2
Click to expand...
Click to collapse
no dice tried it on both even xp i'm gonna give up on it i'll return it its easier
Clutchz said:
Tried it didn't work thanks for the help anyways guys i have a 90 day no questions asked with Costco so i'll take advantage of that any way to export text and call logs? Too much to ask right?
Click to expand...
Click to collapse
Hey do you remember what version of freegee you installed? I think somehow you might have gotten version 1.0.6 instead of 1.1.0. Ive been through everything and the only thing that could have bricked you was using and older version of freegee. I didn't post on xda till Google showed the updated 1.1.0 version was live but maybe somehow you got an older on?
Sent from my LG-LS970 using xda app-developers app
Bootloader NOT UNLOCKED
I was wrong the bootloader is still Locked the developer of the App corrected his app info and this shows that.
http://forum.xda-developers.com/showpost.php?p=43813711&postcount=14
So, I am a victim of the McAfee killswitch. I rooted my phone, then unlocked bootloader, but I made a mistake and had to flash kdz. For some reason, the kdz i downloaded was locked in mcaffee, so i really struggled but managed to install twrp, and of course root. The phone worked fine for a long time, but then I messed up and got a bootloop. The thing is, my killswitch is engaged now, so I can't just go into TWRP and wipe, or go into download mode. Both locked. And if i try to boot normally I just get the loop... So my questions are: Is there a way to get into TWRP directly (without having to confirm, phone could reboot to recovery just fine). Or just flash kdz, i don't know, anything. ADB shows device offline and sometimes unathorized, fastboot doesn't detect it. LG service said it will only fixed if i replace everything. Any help?
Sounds like you need togoba I to stock using lg flash tool
---------- Post added at 03:13 PM ---------- Previous post was at 03:05 PM ----------
ToRt1sher said:
So, I am a victim of the McAfee killswitch. I rooted my phone, then unlocked bootloader, but I made a mistake and had to flash kdz. For some reason, the kdz i downloaded was locked in mcaffee, so i really struggled but managed to install twrp, and of course root. The phone worked fine for a long time, but then I messed up and got a bootloop. The thing is, my killswitch is engaged now, so I can't just go into TWRP and wipe, or go into download mode. Both locked. And if i try to boot normally I just get the loop... So my questions are: Is there a way to get into TWRP directly (without having to confirm, phone could reboot to recovery just fine). Or just flash kdz, i don't know, anything. ADB shows device offline and sometimes unathorized, fastboot doesn't detect it. LG service said it will only fixed if i replace everything. Any help?
Click to expand...
Click to collapse
Try flashing back to stock rom using lg flashtool
moswald1978 said:
Sounds like you need togoba I to stock using lg flash tool
---------- Post added at 03:13 PM ---------- Previous post was at 03:05 PM ----------
Try flashing back to stock rom using lg flashtool
Click to expand...
Click to collapse
I can't access download mode, so I guess flashtool is not an option.
ToRt1sher said:
I can't access download mode, so I guess flashtool is not an option.
Click to expand...
Click to collapse
Try using the kHz method if your computer will reconize your phone. Use LG flashtool 2014 it will put your phone in download mode for you
---------- Post added at 06:06 PM ---------- Previous post was at 06:05 PM ----------
moswald1978 said:
Try using the kHz method if your computer will reconize your phone. Use LG flashtool 2014 it will put your phone in download mode for you
Click to expand...
Click to collapse
Kdz
How will it put my phone into download mode? If i click start, it says the phone is not connected to the computer. My computer can see the device as ADB device, but only offline or unauthorized.
When I used it my phone was stuck on the LG screen. Flashtool found my device and started the upgrade then it booted my phone into download mode
That does not work for me.. The program is stuck at 60% and telling me phone is not connected.
The only other option I can think of would be to a hard factory reset. Make sure your phone is off then hold down power and volume down together when the LG logo appears keep holding them. It should take you to that menu
I already said I can't go into recovery like that, because there is a killswitch activated on my phone.
ToRt1sher said:
So, I am a victim of the McAfee killswitch. I rooted my phone, then unlocked bootloader, but I made a mistake and had to flash kdz. For some reason, the kdz i downloaded was locked in mcaffee, so i really struggled but managed to install twrp, and of course root. The phone worked fine for a long time, but then I messed up and got a bootloop. The thing is, my killswitch is engaged now, so I can't just go into TWRP and wipe, or go into download mode. Both locked. And if i try to boot normally I just get the loop... So my questions are: Is there a way to get into TWRP directly (without having to confirm, phone could reboot to recovery just fine). Or just flash kdz, i don't know, anything. ADB shows device offline and sometimes unathorized, fastboot doesn't detect it. LG service said it will only fixed if i replace everything. Any help?
Click to expand...
Click to collapse
I guess it will be very hard to flash KDZ or TOT cause you need to put your phone to download mode or need to connect ADB. following the post.
ToRt1sher said:
I already said I can't go into recovery like that, because there is a killswitch activated on my phone.
Click to expand...
Click to collapse
did you ever find a solution ?
x000x said:
did you ever find a solution ?
Click to expand...
Click to collapse
No, that's why I asked for help here.
Any news guys? Did somebody find a solution to the killswitch problem?
http://forum.xda-developers.com/sprint-lg-g3/general/guide-fix-hard-brick-recovery-guide-t3132359 try this follow step bye step works on most models
---------- Post added at 10:10 AM ---------- Previous post was at 10:04 AM ----------
This is a cure all for just about all bricks
---------- Post added at 10:50 AM ---------- Previous post was at 10:10 AM ----------
ToRt1sher said:
No, that's why I asked for help here.
Click to expand...
Click to collapse
It may seem hard but its really not
TheMadScientist420 said:
http://forum.xda-developers.com/sprint-lg-g3/general/guide-fix-hard-brick-recovery-guide-t3132359 try this follow step bye step works on most models
---------- Post added at 10:10 AM ---------- Previous post was at 10:04 AM ----------
This is a cure all for just about all bricks
---------- Post added at 10:50 AM ---------- Previous post was at 10:10 AM ----------
It may seem hard but its really not
Click to expand...
Click to collapse
You saved me, thanks a lot!!!
Dear folks, since yesterday i was not able to enter recovery mode. If i press vol up+ power then i can see a small USB icon with a white bar below that. After which nothing is happening. Powen button when pressed continously for 5sec will turn off my mobile and mobile starts again. Mobile is working perfectly. Only issue is unable to enter recovery mode. Can some one help please.....................
have you tried > http://www.asus-zenfone.com/2015/03/zenfone-2-how-to-enter-recovery-wipe.html ?
need to follow this exactly.. finger dance can be tricky but it will work...
I am aware of that bro.i tried many times.i was on custom rom earlier too. Now this us the first time i am seeing this USB icon with white bar below it. Phone is not entering recovery mode.
are u trying to restore ?
Pu$$nBooT$ said:
are u trying to restore ?
Click to expand...
Click to collapse
I am trying to reinstall the latest Global file using ADB
http://www.asus-zenfone.com/2015/12/how-to-downgrade-asus-zenfone-2-firmware.html
try this, ^^^
i followed this method to fix my issue
Try to flash the recovery again.
Pu$$nBooT$ said:
http://www.asus-zenfone.com/2015/12/how-to-downgrade-asus-zenfone-2-firmware.html
try this, ^^^
i followed this method to fix my issue
Click to expand...
Click to collapse
Bro you are not understanding. If the mobile is able to enter recovery mode then i can do all those things, mobile itself is not entering recovery mode. so there is no point in flashing usinng ADB
Using that link you can fix issues ... need to follow it to the letter.. called reading...
---------- Post added at 09:33 AM ---------- Previous post was at 09:30 AM ----------
Follow the guide like it says. You will fix the issues and dont plug the phone in a usb3 port, always use 2.0
Pu$$nBooT$ said:
Using that link you can fix issues ... need to follow it to the letter.. called reading...
---------- Post added at 09:33 AM ---------- Previous post was at 09:30 AM ----------
Follow the guide like it says. You will fix the issues and dont plug the phone in a usb3 port, always use 2.0
Click to expand...
Click to collapse
Downloaded UL-Z00A-WW-2.20.40.174-user.zip and renamed the file to UL-Z00A-WW-2.20.40.178-user.zip.
Copied the file and pasted into internal memory. System recognized the update file and asked me to update. Updated and mobile started normally. Now everything working fine, i was able enter recovery mode.
Hope this helps someone who encounters such type of issue,
So I Bricked my Note 4 a while back and from what i've been reading on the forum is that I need a UnBrick IMage to install to an SD card and may bring it back to life.
It was booting into recovery and USB mode a few times when I was trying to flash stock F/W.
The reason for trying to flash was that it was very buggy, Freeze and lock up a lot.
So I flashed with Odin a few different times to no avail. Most every time it would fail right away, nothing worked.
Anyhow I finally got it to flash successfully and now it doesn't respond, won't go into recovery, won't power on, nothing.
When plugged into PC I Get the Bulk_Qs something or another.
Since I now have noticed that someone has finally successfully rooted the VZW note 4, Iwas hoping there might be a way to get an unbrick image or something.
Any Help would be much appreciated!
Forget about a "unbrick image" or whatever that is. The only way to unbrick Samsung devices is with Samsung Kies. You will need your serial number which is only located on the retail box your phone came in. For some strange reason Samsung decided not to put the serial number on the Note 4 sticker underneath the battery.
Samsung Smart Switch will work as well.
Sent from my SM-N910V using Tapatalk
---------- Post added at 08:44 AM ---------- Previous post was at 08:36 AM ----------
Step 1: Download and install Samsung Smart Switch from here http://www.samsung.com/us/smart-switch/assets/downloads/Smart Switch PC_setup.exe
Step 2: Start the application and hit the "more" tab at the top
Step 3: Hit the "Device initialization" tab
Step 4: Enter your model number exactly like this "SM-N910V" the actual letters must be capitalized.
Step 5: Enter your serial number (Found on your box or purchase reciept) Verizon may also have this information.
Step 6: Just follow the onscreen prompts and put your device into download mode and connect to PC.
Process may take 30 minutes or more depending on your Internet connection.
Sent from my SM-N910V using Tapatalk
---------- Post added at 08:48 AM ---------- Previous post was at 08:44 AM ----------
Many will tell you to download Odin and yada yada yada. The process above will put your device back to factory state. With stock everything. No need to download tars, zips, or any of that other crap you are thinking about. This will wipe your device completely and put you on the latest 5.1.1 firmware.
Samsung Kies will also do this same process. Which can be found here http://www.samsung.com/in/support/usefulsoftware/KIES/
Sent from my SM-N910V using Tapatalk
---------- Post added at 08:49 AM ---------- Previous post was at 08:48 AM ----------
If none of this work... you are scre**! [email protected]
Sent from my SM-N910V using Tapatalk
---------- Post added at 08:54 AM ---------- Previous post was at 08:49 AM ----------
BTW... the serial number is NOT your IMEI.
It will look something like "R38G475A0LX"
Sent from my SM-N910V using Tapatalk
xelanetloads said:
BTW... the serial number is NOT your IMEI.
It will look something like "R38G475A0LX"
Click to expand...
Click to collapse
On a non-bricked phone, is there a way to determine this from the phone? I didn't see it listed in any of the "About Phone" areas.
Nissmo33 said:
So I Bricked my Note 4 a while back and from what i've been reading on the forum is that I need a UnBrick IMage to install to an SD card and may bring it back to life.
It was booting into recovery and USB mode a few times when I was trying to flash stock F/W.
The reason for trying to flash was that it was very buggy, Freeze and lock up a lot.
So I flashed with Odin a few different times to no avail. Most every time it would fail right away, nothing worked.
Anyhow I finally got it to flash successfully and now it doesn't respond, won't go into recovery, won't power on, nothing.
When plugged into PC I Get the Bulk_Qs something or another.
Since I now have noticed that someone has finally successfully rooted the VZW note 4, Iwas hoping there might be a way to get an unbrick image or something.
Any Help would be much appreciated!
Click to expand...
Click to collapse
You'll need an unbrick image. I'll make you one tomorrow. QHSUSB_BULK means an issue with GPT/MBR on eMMC. Rest assured, a MicroSD with the unbrick image should fix your issue.
xelanetloads said:
Forget about a "unbrick image" or whatever that is. The only way to unbrick Samsung devices is with Samsung Kies. You will need your serial number which is only located on the retail box your phone came in. For some strange reason Samsung decided not to put the serial number on the Note 4 sticker underneath the battery.
Samsung Smart Switch will work as well.
Sent from my SM-N910V using Tapatalk
---------- Post added at 08:44 AM ---------- Previous post was at 08:36 AM ----------
Step 1: Download and install Samsung Smart Switch from here http://www.samsung.com/us/smart-switch/assets/downloads/Smart Switch PC_setup.exe
Step 2: Start the application and hit the "more" tab at the top
Step 3: Hit the "Device initialization" tab
Step 4: Enter your model number exactly like this "SM-N910V" the actual letters must be capitalized.
Step 5: Enter your serial number (Found on your box or purchase reciept) Verizon may also have this information.
Step 6: Just follow the onscreen prompts and put your device into download mode and connect to PC.
Process may take 30 minutes or more depending on your Internet connection.
Sent from my SM-N910V using Tapatalk
---------- Post added at 08:48 AM ---------- Previous post was at 08:44 AM ----------
Many will tell you to download Odin and yada yada yada. The process above will put your device back to factory state. With stock everything. No need to download tars, zips, or any of that other crap you are thinking about. This will wipe your device completely and put you on the latest 5.1.1 firmware.
Samsung Kies will also do this same process. Which can be found here http://www.samsung.com/in/support/usefulsoftware/KIES/
Sent from my SM-N910V using Tapatalk
---------- Post added at 08:49 AM ---------- Previous post was at 08:48 AM ----------
If none of this work... you are scre**! [email protected]
Sent from my SM-N910V using Tapatalk
---------- Post added at 08:54 AM ---------- Previous post was at 08:49 AM ----------
BTW... the serial number is NOT your IMEI.
It will look something like "R38G475A0LX"
Sent from my SM-N910V using Tapatalk
Click to expand...
Click to collapse
This won't work for the state his phone is in.
I see.
Sent from my SM-N910V using Tapatalk
---------- Post added at 05:10 PM ---------- Previous post was at 05:08 PM ----------
Sizzlechest said:
On a non-bricked phone, is there a way to determine this from the phone? I didn't see it listed in any of the "About Phone" areas.
Click to expand...
Click to collapse
I semi bricked my device once screwing around and couldn't find anything on the phone or any software to get the correct serial number.
Sent from my SM-N910V using Tapatalk
xelanetloads said:
I see.
Sent from my SM-N910V using Tapatalk
---------- Post added at 05:10 PM ---------- Previous post was at 05:08 PM ----------
I semi bricked my device once screwing around and couldn't find anything on the phone or any software to get the correct serial number.
Sent from my SM-N910V using Tapatalk
Click to expand...
Click to collapse
Are you on Windows? I'll have an unbrick image today. You'll want to install Win32DiskImager, and make sure you have an SD reader.
Yeah I'm on windows and have an SD reader.
I greatly appreciate it.
Sent from my SM-G900V using Tapatalk
My note is working fine, but I love having stuff like this handy for when I inevitably break something? ! Would be appreciative of you guys update this thread with the undock image and some instructions!!
Sent from my Nexus 7 using Tapatalk
I too am curious about this "unbrick image"
I have a Galaxy Mega that enters download mode but fails every attempt to flash anything. Once powered on it displays a download mode error with yellow triangle. Recovery mode not working as well. For me, that's a "brick"
Sent from my SM-N910V using XDA-Developers mobile app
!!Update!!
ryanbg sent me the unbrick image through PM. I used wind32diskimager to put the image on SD card, popped it in my note 4.
(The phone had been setting on my dresser for 6 weeks or so dead). after putting the sd card in I remembered reading that the battery needed to be at least 10% so I plugged the usb cable into my pc And BAM! it powered right into USB mode.
So then I wasn't sure if I needed to flash with Odin or anything. Anyway I plugged it into the wall charger and pressed the power button and the phone rebooted and come right on like normal boot. So I went to bed and let it charge over night.
Got up this morning opened it and set up my Google account and everything was running like normal. So I powered the phone down.
Now it is doing the same freaking thing, No Power, no lights, no vibration.
The only thing I can get it to do is while holding the power and Volume down key, plug into pc and pops up QHSUSB_BULK.
I'm so frustrated with this POS! What am I doing Wrong?:crying:
BTW here is the unbrick image download https://www.dropbox.com/s/4vye9t9178vr1k9/N4_UNBRICK.zip?dl=0
Nissmo33 said:
!!Update!!
ryanbg sent me the unbrick image through PM. I used wind32diskimager to put the image on SD card, popped it in my note 4.
(The phone had been setting on my dresser for 6 weeks or so dead). after putting the sd card in I remembered reading that the battery needed to be at least 10% so I plugged the usb cable into my pc And BAM! it powered right into USB mode.
So then I wasn't sure if I needed to flash with Odin or anything. Anyway I plugged it into the wall charger and pressed the power button and the phone rebooted and come right on like normal boot. So I went to bed and let it charge over night.
Got up this morning opened it and set up my Google account and everything was running like normal. So I powered the phone down.
Now it is doing the same freaking thing, No Power, no lights, no vibration.
The only thing I can get it to do is while holding the power and Volume down key, plug into pc and pops up QHSUSB_BULK.
I'm so frustrated with this POS! What am I doing Wrong?:crying:
BTW here is the unbrick image download https://www.dropbox.com/s/4vye9t9178vr1k9/N4_UNBRICK.zip?dl=0
Click to expand...
Click to collapse
Did you take the SD card out?
Yes I did.
Update #2 after the phone sits until the battery drains.
It will come back on after plugging it into a charger.
Now it's back like when I bought it. Randomly turns off and freezes and sometimes won't power up.
Sent from my SM-G900V using Tapatalk