Is there any way for the fire TV to connect to it? My university uses it, and I was wondering if I could connect, but the access point is not showing up
Can´t look now because I´m not at home but wasn´t there a setting for a manual AP setup where you could enter the SSID by yourself?
Some organizations may keep a second network available for legacy devices like printers, XBoxes, and older machines. You can check with your university's tech support to see how you can add your device to the list of allowed access for that network.
This isn't a guarantee that this network exists for you, but most enterprise and even some residential-grade equipment have this capability.
Otherwise, you might be able to find a router or range extender that can understand and connect to WPA2-Enterprise to work around this. In a pinch, an old laptop with two wifi cards or a wifi Ethernet port should suffice.
Or you may want to scrap wifi and run an Ethernet cable to your dorm's jack or personal switch.
Related topics found through Googling, but no further help:
https://www.reddit.com/r/cordcutters/comments/2sv1ov/best_option_for_college_wifi/
https://www.reddit.com/r/fireTV/comments/2mydhh/fire_tv_stick_can_you_use_a_wireless_network_that/
Thanks the responses, but neither of them works well for me. there is a secondary unsecured wifi network, but it is just too slow to use, especially for streaming videos. I sideloaded a wifi APK onto it, and the networks DO show up, but there is no way to enter the login information (you need both a username and password.) Anyone know of an app that can do that?
Related
Hi guys, I recently destroyed my XDA2 and got a 2s on the insurance
Bluetooth on WM2003 SE if fair poor, but I managed to upgrade the stack thinger to 3900..... so I'm not completely XDA illiterate.
However, the wifi baffles me! I have access to an unsecured wireless network with internet access, and my 2s will connect to it. When I go on the the internet on my XDA, even with wifi connected it still tries to connect GPRS to use the internet. If I keep clicking cancel, it will load the page (presumably through the wireless network's internet access).
It has become clear that I have no idea what I'm doing with regards to networking. Could someone post a quick guide as to how to set up the wifi (from scratch) so that when it finds an unsecured network it will automatically use it for the internet.
Sorry if there's already a thread on this but I really can't find it. Cheers guys
-Mike
just what i need as well, i have just bought a wifi router so i can use the internet on my xda2s.
using the wireless manger -> wireless LAN manager i get:
STATUS: connected to network
SSID: NETGEAR
TX RATE: AUTO
MODE:INFRASTRUCTURE
CHANNEL 11
BSSID: 00-09-5B-D7-DC-2A
MAC: 00-09-2D-0B-C0-A6
but even when i pull the Ethnet cable (forgot how its spelt) out of the back of the router it still stays connected. so im thinking its more my PC than the xda. the thing is the router came with no software so i have no idea if its connected properly. when i pull this Ethnet cable out of the wifi router o get network cable unplugged. The network card is Broadcom 440x 10/100 Integrated Controller. Which I have never used.
if anyone has a any ideas it would stop me pulling my hair out.
Sorry to hijack this thread
mike freegan said:
However, the wifi baffles me! I have access to an unsecured wireless network with internet access, and my 2s will connect to it. When I go on the the internet on my XDA, even with wifi connected it still tries to connect GPRS to use the internet. If I keep clicking cancel, it will load the page (presumably through the wireless network's internet access).
-Mike
Click to expand...
Click to collapse
Mike, I dont think the wifi first and GPRS next works. It doesnt work properly on mine either. If I try a internet access via gprs and a local wifi is readily available, the system does not automatically switch to local wifi.....I think this could be a microsoft issue than a xda issue.
robboy said:
but even when i pull the Ethnet cable (forgot how its spelt) out of the back of the router it still stays connected. so im thinking its more my PC than the xda. the thing is the router came with no software so i have no idea if its connected properly. when i pull this Ethnet cable out of the wifi router o get network cable unplugged. The network card is Broadcom 440x 10/100 Integrated Controller. Which I have never used.
Click to expand...
Click to collapse
when u pull out the ethernet cable from the back of the router, can you still surf the net from you xda or PC?? that seems odd. So either you are not connecting to "your" own router, or someone else has a same router with unsecured setup and you were locked onto their service....if you follow what I mean. what happens if you kill the power to your router? you should definitely notice that the wifi service disappear in your xda and PC.
Dont expect a router to disappear by simply unplugging the ethernet cable, if the router is powered up, it will show up on your xda and the PC although obviously there will be no internet access.....
sorry if i wasn't clear. i meant i was still receiving a signal from the wifi router. i could never use the internet on the pda
update:
i can browse my pc files wirelessly using resco explorer, using the standard file explorer i can view the pc files using \\network/c and i have finally been able to connect to activesync.
however i still can not connect to the internet.
Any ideas, from looking on this forum it seems lots of peeps are having problems with this but nobody seems to have the answer
XDA Wi-Fi Solution....It Works!!!!
Hi,
I'm new to the forum and new to XDA2i (presumably XDA2s is same!) ....
I too had many frustrations connecting the wi-fi...but now I've cracked it, here's how.......
On first very first use (or following a hard re-set) device users are prompted to choose “What do you want WLAN to connect to?” The option bullets are ‘Internet’ or ‘Work’….’Work’ should be selected, this will connect them to the nearest WLAN (if this network is WEP encrypted it should be switched to ‘Open’ rather than ‘shared’ as is often the case).
Next prompt asks for any WEP Encryption ‘Pass Key’ to be input, when doing so omit any ‘-‘ between character pairs. Normal start-up should then be completed. Once device is up and running…..
From ‘Start’ pull-down on the ‘Today Screen’ select…. ‘settings’>’connections tab’>’connections icon’>’advanced tab’>’Select Networks’> pull-down ‘My Work Network’ > ‘OK’ out of selections to save and exit.
Go to ‘Wireless Manager’ in programs, select WLAN icon from main screen (which should turn green to show active), then select mini ‘WLAN’ icon from lower toolbar to see the status of the connection, quality of signal etc.
That did it for me......
Cheers
windupmerchant
Hi everyone!
I'm having kind of a special problem.
I'm an electro acoustic musician and finds the Desire a lot of fun.
My new project is to use its accelerometer etc and for that I need to connect it to my Mac running OSX 10.6.5.
The issue I'm having is that my network (campus ish) won't allow me to open any ports. I don't think it's a good idea to hack it, so my next idea is to create a network between my Mac and my Desire. This network won't have access to the internet.
It also has to be via Wifi since the app I'm using only allows communication through wifi and my java skills aren't good enough to edit the apk.
I therefore run Oxygen 1.0 (GREAT rom btw) which is supposed to accept ad-hoc, and my computers own network does show up when i browse it in my phone.
The problem is that it dosn't connect since it isn't given an ip. I imagine there has to be a solution to this and I'm just not seeing it. I'm also thinking it could be an OSX issue and not really a question for this forum, but I'm pretty sure it should be possible to just make the phone not requesting an internet ip.
I've tried to set a static IP but this won't work ether.
Does anyone have a clue on how to do? I'm quite desperate really. Been searching for a solution online for quite some time and I haven't found the right one. Probably because most people using ad-hoc want it's phone to connect to the internet and therefore not having my kind of trouble. Unfortunately I have no way of connecting my computer to the router with wire since the router is about 400 meters away. Once of corse, but i really need a wireless solution in the long run.
Thanks!
Christopher
So I've been using the Tom coding package that installs the mobile Wi-Fi router with no problems until last night... now it keeps trying to connect to ISP.Cingular and then stops... it basically doesn't work now. I've tried to uninstall and reinstalled it dozens of times with no luck.
And yet... the 3G connection works because I can browse through Opera. So...?
OhI might add that I can turn on the Wi-Fi and connect to my in-house router just fine and do what on the internet through the phone. SO... it is definitely something specific with wireless internet sharing.
???
Someone please he me I use internet sharing DAILY
You need to make sure that it is connecting to the correct address. At the bottom of the App, it should have a few different choices of connections to use. Try another one and see if it works. You may have to set up a new connections for this to work properly. Keep in mind that tethering/mobile hotspot is not covered by AT&T's wireless data plan. It is a separate monthly charge. You should be careful when using it too much at a time, so they don't block or throttle your connection.
The device I am trying to connect with to my Tilt 2 is a Samsung Galaxy Tab, and apparently it doesn't like ad-hoc, whatever that is exactly. I was told on the Galaxy Tab section of this forum that this is the case, and that I need some kind of "mobile ap", although again I do not understand what that exactly means. ???
Ah, see that's much better information. So, no, you probably won't be able to connect without another app doing so. Ad-hoc is, simply put, a connection to another device other than a router which is allowing you access to its Internet connection. If the device you're trying to connect with doesn't allow ad-hoc connections, then the Wifi Router app won't do you any good, as that is the type of connection it uses. Most mobile devices do not natively support this, however. The problem, therefore, is with the Galaxy Tab you have, not with the TP2. Find an app or mod that allows for ad-hoc connections and you'll be all set.
Well is there an apparently for the WM phone side of things that will do non ad-hoc??
No. Ad-hoc is a connection between two devices. Unless you use a router, that's how it's going to be no matter if you are using WM, a laptop, iOS, Android, et cetera. The connection type is determined by the device sending the signal. If it comes from a device, then it is ad-hoc. It is not a problem with the software. That is how wifi was designed to work in the first place. The problem, again, is with the Tab, not the WM application.
Well apparently there is a solution for the Tab that allows it to see ad-hoc networks, so I will try that and let you guys know how it went.
Can no longer connect to Ad-Hoc with Tilt 2
I have been using both the CM Internet Sharing program and the WMWifiRouter with no issues for over a year now on my AT&T Tilt 2.
One day a couple weeks ago I had been using CM to connect my laptop to the internet. everything was just fine as usual.
At some point, I had disconnected and tried to reconnect, and since then I can no longer use either of these programs.
What happens is this...I turn them on and the phone will no longer hold a connection to the ad-hoc network that is created. Up in the status bar I see the icon showing WiFi trying to connect but it will not stick anymore.
I can connect to my office and/or home wifi router still. It just will not connect to the ad-hoc network any longer.
This makes no sense to me at all, since it has always worked and was even working earlier in the day when it stopped working.
I use the tethering frequently and really need to get this solved. Any help would be greatly appreciated.
Hello,
I want to use portable Wi-Fi hotspot on my phone to connect to my laptop in places where public wi-fi is not available, or to connect to two computers to each other. And it seems to be working.
But I have a problem. I do not want to use mobile network to access Internet for those computers. I want only to exchange data between phone and computer, or between computers themselves.
But every time I switch on hotspot, 3G connection switches on automatically, even if it is switched off on purpose. I know this is intended use of hotspot, but I have a question:
Is there a way to prevent phone switching 3G network on in wi-fi hotspot mode, or just preventing data traffic over 3G?
Or I am missing the point completely?
The application is not intended for such usage; all it does is route traffic between connected wlan-clients and the carrier's apn. The phone itself has the ip-address 192.168.1.1 during this setup, but it is not listening on any ports that would be useful for your setup (ie 'cifs/samba').
LeeCHeSSS said:
The application is not intended for such usage; all it does is route traffic between connected wlan-clients and the carrier's apn. The phone itself has the ip-address 192.168.1.1 during this setup, but it is not listening on any ports that would be useful for your setup (ie 'cifs/samba').
Click to expand...
Click to collapse
I do not know if I do understand you but here are the facts:
I connect two dell laptops to portable wi-fi hotspot on my wildfire s:
one is : 192.168.1.135
other : 192.168.1.185
I can ping one from another. If I share a folder in one (.135) and go to others(.185) "Search for computers or people" I see all files in shared folder and can do all the usual operations over them (edit, move...)
Also if I install Remote Web Desktop from Market on my phone I can access phone through web interface.
In a word, I can do all things as on "normal" wi-fi network ( and I promise it is the only network around here ) except all the time I have 3G switched on. And I do not want to do that because I see my network data traffic going up.
So, as I see things, my only problem is unwanted 3G traffic.
Help?
Ah, but you did not mention that you had installed a seperate application to open up a port for the webinterface.
This however does not change the intended usage for the mobile wifi hotspot application!
hey...you can try this:
1. go to your mobile network settings
2. create a new APN, a dummy one
3. set the new APN as default
4. launch your wifihotspot
I did not test it with 2 pcs but, when u launch wifihotspot, 3g no longer comes on and my pc still connected to the wireless network without any problems.
Let us know your results
Cheers,
Hey,
I ran more test on this issue. The previous posted solution works like a charm.
I was able to use the wifihotspot as a wireless access point:
1. 2 or more PCs can communicate with each other (browse folders)
2. If one of the PCs has internet access, it shares to the rest of the PCs
3. If one of the PCs has an ethernet connection to a server, all other PCs also get connection to the server
For 3. to work, you will need to brigde the local area connection with the wireless connection on the PC that has cabled ethernet connection. Also browsing folders will work only if you use \\server ip (\\servername does not work).
I will try getting DNS access via the hotspot later.
Hope this helps
Hi all, first post so sorry if it's in the wrong place! I seem to have an issue connecting to my Fire Stick via adbfire. Adbfire won't connect to my Stick (Followed all steps required) and I have a feeling that it could be because I'm connected to my university Halls of Residence WiFi which is a shared network; is it possible that because of this the IP Address on my laptop won't match the one with the Stick? If so, is there any possible workaround to be able to get Kodi on the device?
Many thanks!
John
Hi,
Most universities employ Layer 2 client isolation, so that one wireless client is not able to communicate with another client. You will likely need to bring in your own router and use your own wireless SSID (against most university network AUP) in order to connect and push things via ADB.
Easiest workaround I can think of is to create your own wifi network, either by using your own router (even without an active internet connection, there are cheap ones available) or you could try a laptop/desktop or a smartphone.
If you have a wired ethernet connection or get a router which can connect to another wifi network, you may be able to get away with your own router all the time, but it's a gamble depending on your uni (mine apparently claimed that they would ban people, but I've been using a cable router without any problems so far (touch wood)).
If you go the path of your own router, be sure you hide the SSID.
The Cisco APs we used, at the university I used to work at, had a dubious "feature" that would actively search out "rogue" SSIDs and would continuously associate/deassociate with them in order to overload the AP and cause them to lock up. They didn't want students using other public available SSIDs for fear of privacy concerns.