Related
hu. i have a problem. The only thing my htc show is a black screen. the light is on, but nothing displayed. i try to enter bootloader mode but still only the black screen. can anyoane tell me what can i do? i hope is not a hardware problem...
oh, is htc tinity...
If You`re lucky it`s just a loose contact. If You can still hear the sounds from the splash screens I`m sure its nothing worse. Had this too and the fix is really easy once You`ve done it. I had to do it numerous times until I had a good solution. Look in the general trinity subforum, there`s a post on how to disassemble the phone. You have to do steps 1-5 to get the back cover off.
Then You can do an easy test:
- Put the battery back in again. I used some paper cut to size as underlay just to be sure not to accidently short anything should the battery move from its place.
- Hold the phone in such a way that You can apply light pressure on the battery so it stays connected. Now You can power on the phone.
- Apply some light pressure on top of the lcd connection cable (marked red in the disassembly guide) and see if You have a picture again.
- If this doesn`t help try to apply light pressure with a plastic or wood piece from the side where it vanishes in the front cover. In other words play a little bit with pressure direction.
If You get Your picture when applying pressure everything is fine cause all You have to do now is to put in something to polster out the back cover (or side cover, depending on where You pushed from when the screen came back alive). There is a small soft black sticker on the back cover that applies some pressure by default, use this as guidance. First I just rolled a piece of paper and positioned it there when I closed the cover. Didn`t hold for long. Finally I applied a sticker used on furnitures to protect wood floors. Same as vibration dampener stickers for loudspeakers. Just cut to size, stick on top of the old sticker or into the side housing and You`re good to go. Never had a problem with it again.
It sounds far more complicated as it is and You should really try it. I wish You it`s just a loose contact.
So I decided to NOT but a case around my pretty phone an go naked for a bit. The concern is about the camera lens. I have been getting more and more "careless" with the phone.. not putting it on a soft napkin and just laying it on a table. I have a screen protector on the front so maybe I should just lay it face down. But I am wondering.. anyone have an issue with the camera without using a hard case? The lens actually seems pretty strong....
I've never used an extra case for a phone, they already come with a nice sexy hard plastic one. However with the Evo i would never use it without a screen protector. I think the lens is decently strong, it can take being set down on. Still be careful though.
I use nothing at all not even a screen protector..and it's in perfect condition..i hope it stays like that
-------------------------------------
Sent from my Htc Evo 4g
I am hunting for a case right now. The phone got pushed by someone's elbow across the table and the sound nearly made my ears bleed and my heart stop. Luckily it didn't do anything to the raised camera, but I am not risking it again.
The Nexus lens is a lot like the Evo lens. I've had mine going for 3 months with rough use and there are a few tiny scratches on the lens, but nothing major. it doesn't effect the image quality at all.
I wouldn't be too worried
my zagg came with a cut out for the camera, going to just drop that on there
I got rid of my Hard case and got the Zagg full body and seidio holster my camera is holding up fine no scratches and i don't lay it flat on the screen
Do what I do...
Pop open the back case, and put on a square piece of CLEAR tape (not the scotch kind), packaging tape seems to work pretty well. Make sure it doesn't overlap on to the back speaker as it can reduce the phone's loudness. Then put the case back on. From time to time just replace the tape when it gets too scratched up.
Screen protector and nothing else. I normally leave the phone screen down on the desk.
I am not that concerned about the camera. There is always a way to replace parts on these phones (you can replace the screen 'relatively' easily also). I am sure I would be able to replace the camera cover/plastic/glass piece.
going streaking
been using it with out any screenprotectir abd case, not a single scratch *knock on wood* the new age screens are not ment to be used with a screen protector, and case just BLAH UGLY
I use a black silicon case and screen protector. I went nude for a while and I was just too nervous about it. The case is easy to take off, so if I let someone play with it, I often just take it off first so they can see just how nice the phone is. Something I like about the case is that the lens doesn't touch the surface when I lay it down - and I don't lay it on the screen, not that it would matter.
Another plus is that it doesn't slip out of my pocket like it used to (and any other phones I've had) when I'm active. Lots of pluses. Just too bad this particular one doesn't look that cool (not bad though). I'd really like to find a similar case that actually looks cool, maybe sporty.
I always use the kickstand and just prop up my phone. I am having no issues at all.
no case no nothing
it's gonna get wear and tear
but you're gonna get a new phone in 1 - 2 years anyway right
I always use a case to keep the phone in good condition for when I sell it after I'm done with it. It always gets top dollar since all the other used ones online being sold are junked up. But to each their own I suppose. Good luck!
No case, no screen protector. Looks like it did when I got it June 4th.
I just ordered this today: http://www.handhelditems.com/product_info.php?cPath=3524_5132_7769&products_id=135999
And it's cheap and it looks like it will do the job just fine with out adding much profile. I'd choose this over a naked alternative. Mine is partially naked, it has a screen protector and has been fine since.
I'll let you know how this case is when I get it.
rutter9 said:
I always use a case to keep the phone in good condition for when I sell it after I'm done with it. It always gets top dollar since all the other used ones online being sold are junked up. But to each their own I suppose. Good luck!
Click to expand...
Click to collapse
Same here. I always sell mine cause they still look new. I sold my Moment when I got my EVO and got $230 for it on eBay.
Sent from my EVO using Tapatalk
I don't use a case and the camera is just fine, no scratches at all. I even dropped my phone on concrete like, the 3rd day I got it (missed my pocket lol) and the phone is completely fine, aside from a scratch on one of the corners that isn't noticeable unless you're looking for it. Speaking of which... I WANT A BUMPER CASE!! like this.. except black lol.
http://thenextweb.com/mobile/2010/06/11/pictures-of-iphone-4-bumper-cases-surface/
if anyone finds one let me know
I do not have any screen protector or case, and (until I get a dock) I set my phone down camera face down. I got it opening day and have no scratches on the screen, but there are tiny, minute scratches on the camera lens glass. Though they are contained within the black, non-lens area that reads "8.0 Megapixels". It almost seems like this was intentionally done, as when you set the phone down on the camera, it's at an angle and the viewable part of the lens doesn't seem to touch the table. Photos I take are unaffected. It seems harmless and I will keep going "naked" with mine. I'll try and take a close up pic of the affected area if anyone wants to see.
I've been really careful with the phone but got my first scratch on the lense yesterday. It must have happened in my pocket yet I only keep the phone by itself in there. The Evo is a beautiful phone but having that protruding lens is a retarded design.
Hi all,
I absolutely just got my Z1c (didn't even turn it on yet), and the first thing that called my attention is that there is a screen protector on the box... so, a few questions:
1) Does this mean that there is no screen protector already installed on the screen?
2) Is it worth installing it or not? I've read that on the regular Z1, the protector is only for shatter protection, but is actually not scratch resistant... if this is also the case for the Z1c, I guess that I will do without the protector... any other reason to install it?
PS: this baby just arrived after pre-ordering it at Sony Mobile Italia...
Thanks,
Leo.
Put it on, should it ever be scratched it is way easier to replace than the original anti-shatter-film mounted on the display panel. And don't forget to protect the back as well, it's only plastic...
----------
tapatalked from Android
urriki out
i almost forgot about that. was too excited to finally be getting a proper phone to be looking at what was in the box.
if you look up where the notification light is, and hold it against the light in a certain way you should be able to see it. they did a neat job of it. i still dont understand why it is there really. if my screen shatters im not going to be able to use the phone any more. maybe they are worried about glass going all my pocket if i break it. umm thanks sony. how thoughtful of you
So while walking downstairs to my basement, I tried to put my phone back into my pocket and it slipped and dropped on the hard floor. It dropped about 4 ft and it had a hard plastic case around it (one of the Korean model cases with the small section exposed though). The glass screen protector I had on it cracked, but the actual screen is fine. I tried turning the phone back on, but only the notification light comes on and it keeps blinking green and blue.
EDIT: So I guess the LCD is broken cause the digitizer is completely intact and there's no indication that the phone was even dropped. Usually its the other way around.....
sonicspear64 said:
So while walking downstairs to my basement, I tried to put my phone back into my pocket and it slipped and dropped on the hard floor. It dropped about 4 ft and it had a hard plastic case around it (one of the Korean model cases with the small section exposed though). The glass screen protector I had on it cracked, but the actual screen is fine. I tried turning the phone back on, but only the notification light comes on and it keeps blinking green and blue.
EDIT: So I guess the LCD is broken cause the digitizer is completely intact and there's no indication that the phone was even dropped. Usually its the other way around.....
Click to expand...
Click to collapse
Exactly the same thing happened to me. No visible damage, but screen wont come on. LED is blinking blue and green.
Do you have any new updates regarding your phone problem?
sonicspear64 said:
So while walking downstairs to my basement, I tried to put my phone back into my pocket and it slipped and dropped on the hard floor. It dropped about 4 ft and it had a hard plastic case around it (one of the Korean model cases with the small section exposed though). The glass screen protector I had on it cracked, but the actual screen is fine. I tried turning the phone back on, but only the notification light comes on and it keeps blinking green and blue.
EDIT: So I guess the LCD is broken cause the digitizer is completely intact and there's no indication that the phone was even dropped. Usually its the other way around.....
Click to expand...
Click to collapse
try to point a light on the screen if you can see some cracks...
FYI: i dropped mine 3 times (all face down) and it survived ?
From about 3 ft...
also i have the tempered glass screen protector plus a fake spigen slim armor on it ?
Sent from from my LG-D855
LittleCannon said:
Exactly the same thing happened to me. No visible damage, but screen wont come on. LED is blinking blue and green.
Do you have any new updates regarding your phone problem?
Click to expand...
Click to collapse
The only new thing that I discovered was that the backlight is probably broken. I can see a very faint image of the LG boot logo and the carrier logo when the phone boots up, but it just hangs there and the LED keeps blinking till the battery runs out/is taken out so I don't know what else is up.
EpicChineseTime said:
try to point a light on the screen if you can see some cracks...
FYI: i dropped mine 3 times (all face down) and it survived ?
From about 3 ft...
also i have the tempered glass screen protector plus a fake spigen slim armor on it ?
Sent from from my LG-D855
Click to expand...
Click to collapse
No cracks at all. The only crack I had was on my tempered glass screen protector. I thought it was the actual screen, but I took it off and the screen was unscathed.
sonicspear64 said:
The only new thing that I discovered was that the backlight is probably broken. I can see a very faint image of the LG boot logo and the carrier logo when the phone boots up, but it just hangs there and the LED keeps blinking till the battery runs out/is taken out so I don't know what else is up.
No cracks at all. The only crack I had was on my tempered glass screen protector. I thought it was the actual screen, but I took it off and the screen was unscathed.
Click to expand...
Click to collapse
Did you manage to repair it?
sonicspear64 said:
So while walking downstairs to my basement, I tried to put my phone back into my pocket and it slipped and dropped on the hard floor. It dropped about 4 ft and it had a hard plastic case around it (one of the Korean model cases with the small section exposed though). The glass screen protector I had on it cracked, but the actual screen is fine. I tried turning the phone back on, but only the notification light comes on and it keeps blinking green and blue.
EDIT: So I guess the LCD is broken cause the digitizer is completely intact and there's no indication that the phone was even dropped. Usually its the other way around.....
Click to expand...
Click to collapse
Take it back to and tell them that the phone just stopped working. I'm sure they will fix it under warranty.
Sent from my LG Gangster 3
Small update!
I have just receive phone from warrany repair.
Apparently, motherboard was broken!!!!
LittleCannon said:
Small update!
I have just receive phone from warrany repair.
Apparently, motherboard was broken!!!!
Click to expand...
Click to collapse
Ive just dropped mine from sitting on the loo, 2 foot drop if that and again, wont turn the screen on led flashed blue/green omg, not having a good day after being late for work cos the car ran out of petrol while I was scraping the windows, then broke the key off in the lock for the shed, had to break into my shed only to find the petrol can was empty, defrosted my wife's car and went n got some petrol in the can, fitted the filler pipe to the can, on putting the petrol in the car the pipe snapped off so had to go hunting for another, now I've just dropped my sodding phone gurrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrr
Ive just shined a light on it and it is on and working but screen is black without the torch, managed to turn brightness to full, no better.
Update, phone was deemed not repairable by my phone insurance through my bank so they sent me a brand new one yummy ?
Hi all-
My MZF went for a swim a couple weeks back. Put it in a bag with some DO NOT EAT desiccant packets for a few days, actually got it to turn back on, except the Power Button didn't work and the camera crashed every time I tried to open it.
I replaced the camera module and volume rocker/power strip with OEM used parts from eBay. Phone came back on, power button and camera worked, and everything actually seemed good until I plugged the phone in to charge.
I came back a little while later and the screen is black. Phone still vibrated on fingerprint touch, and when trying to power up/down with the power button. Did not come back on reboot, and every so often can see a very brief flash on the screen. No sound either. Thinking I somehow fried the display when I plugged it back in. Thinking about getting a replacement, but all the used ones on eBay are scratchy and/or burned in, and all the "new" "OEM" ones just seem shady.
Anybody ever done anything like this? Looking for any insight!
get a scratched screen and lay a glass screen protector on it this will hide some imperfections and prevent more. i replaced my screen once already and it waqs a pain but my moto branded part works great it came from a bad imei number
Found a decent OEM screen on eBay, didn't appear to be in too bad of shape. Definitely going to put a screen protector on it to help with any scratches. Sitting in my PO box right now, and and gonna try installing it this evening!
I am debating replacing mine. The screen scratched at the FFC and made any front pictures blurry. Did some rigging as a temp fix, but the camera sensor is now not covered by the plastic. If I do replace of, I'll do a tear down video. The screen isn't too hard to remove. Of almost came of when I ripped the protector off.