Related
So I have an Att Note 2, which is bricked or soft bricked. I am a very rookie Android guy when it comes to modifying or hacking. I did root my Note 2 with Cyanogenmod. However, I missed S Note and the use of my S Pen so I researched a bit to get back to stock with the use of Odin and stock roms found on the net. I was successful, and actually amazed it worked. Long story short, a few days after that, an OTA update hit my phone, didn't even think about it and began the download. The phone downloaded the update, and rebooted to complete the install. The problem is, during reboot, the phone got stuck on the "Samsung Galaxy Note II" screen. I researched a bit online, and everyone said get to recovery mode and do a few things. Problem is, I can't get into recovery mode, I can only get the screen described above, and the download screen, THAT IS ALL. Looked a bit more online and attempted to flash various stock roms with Odin. Some were successful, Odin passed, and the phone would get stuck on the Note II screen again, and would not boot into recovery mode, same issue with only being able to access download mode. The unsuccessful flash attempts got me to screen informing me that Kies needs to be used to update my firmware. Kies showed a recovery code, which was downloaded, but unsuccessful. It would download all the way, but at the end of install, it would fail. Funny thing is it would work enough to get me back to the ability to get into download mode. I just want my Note 2 working again. Is there any way to wipe my phone completely clean, and start over? Or is there any way to even re-root it, or flash any sort of rom on there, just so I can use the damn thing? I need some help by you pros out there ! Please!
titostats said:
So I have an Att Note 2, which is bricked or soft bricked. I am a very rookie Android guy when it comes to modifying or hacking. I did root my Note 2 with Cyanogenmod. However, I missed S Note and the use of my S Pen so I researched a bit to get back to stock with the use of Odin and stock roms found on the net. I was successful, and actually amazed it worked. Long story short, a few days after that, an OTA update hit my phone, didn't even think about it and began the download. The phone downloaded the update, and rebooted to complete the install. The problem is, during reboot, the phone got stuck on the "Samsung Galaxy Note II" screen. I researched a bit online, and everyone said get to recovery mode and do a few things. Problem is, I can't get into recovery mode, I can only get the screen described above, and the download screen, THAT IS ALL. Looked a bit more online and attempted to flash various stock roms with Odin. Some were successful, Odin passed, and the phone would get stuck on the Note II screen again, and would not boot into recovery mode, same issue with only being able to access download mode. The unsuccessful flash attempts got me to screen informing me that Kies needs to be used to update my firmware. Kies showed a recovery code, which was downloaded, but unsuccessful. It would download all the way, but at the end of install, it would fail. Funny thing is it would work enough to get me back to the ability to get into download mode. I just want my Note 2 working again. Is there any way to wipe my phone completely clean, and start over? Or is there any way to even re-root it, or flash any sort of rom on there, just so I can use the damn thing? I need some help by you pros out there ! Please!
Click to expand...
Click to collapse
Download the latest kies from the samsung website.. and then open tools and then firmware update and initialization.. pull out the battery and type the model number and serial number kies asks.. follow the instructions.. your phone will be fine..
Sent from my GT-N7100
titostats said:
So I have an Att Note 2, which is bricked or soft bricked. I am a very rookie Android guy when it comes to modifying or hacking. I did root my Note 2 with Cyanogenmod. However, I missed S Note and the use of my S Pen so I researched a bit to get back to stock with the use of Odin and stock roms found on the net. I was successful, and actually amazed it worked. Long story short, a few days after that, an OTA update hit my phone, didn't even think about it and began the download. The phone downloaded the update, and rebooted to complete the install. The problem is, during reboot, the phone got stuck on the "Samsung Galaxy Note II" screen. I researched a bit online, and everyone said get to recovery mode and do a few things. Problem is, I can't get into recovery mode, I can only get the screen described above, and the download screen, THAT IS ALL. Looked a bit more online and attempted to flash various stock roms with Odin. Some were successful, Odin passed, and the phone would get stuck on the Note II screen again, and would not boot into recovery mode, same issue with only being able to access download mode. The unsuccessful flash attempts got me to screen informing me that Kies needs to be used to update my firmware. Kies showed a recovery code, which was downloaded, but unsuccessful. It would download all the way, but at the end of install, it would fail. Funny thing is it would work enough to get me back to the ability to get into download mode. I just want my Note 2 working again. Is there any way to wipe my phone completely clean, and start over? Or is there any way to even re-root it, or flash any sort of rom on there, just so I can use the damn thing? I need some help by you pros out there ! Please!
Click to expand...
Click to collapse
Try flashing a recovery for ur device with Odin, not a ROM, just flash twrp recovery with Odin, after u flash the recovery u will be able to access recovery and flash a stock ROM through twrp. I think what happened to u is when u flashed the update it tried to right over the unlocked bootloader which caused the soft brick, try flashing the recovery for ur device and if that doesn't work try the above posters way...
Sent from my Nexus 5 using XDA Premium 4 mobile app
Hey,
after my Tab 3 10.1 (P5200) got the KitKat update not so long ago, it went to an kinda unusable state, due to the cant write on External SD Card thingy.
So yesterday after checking out my options (Root or Update to Android 5) I decided to go for the root, since the Android 5 version is supposed to be a bit buggy.
Anyway, after my initial Odin try the tablet stuck at the "Galaxy Tab 3" logo, I think it was due to having a slightly different version than the root file was for.
So after that failed, I downloaded my stock firmware (P5200XXUBOB1_P5200DBTBOB1_P5200XXUBNK1) and also used Odin, which resulted in my tablet starting flawless again. But since it was the stock version, unrooted again, which is again, an unusable state.
So I went with this (http://forum.xda-developers.com/gal...-10/rom-100-stock-4-4-2-kitkat-p5200-t2866066) thread, and tried the rooted version, put it in the root of my SD Card and installed it per recovery menu, which "worked" but got me stuck on the Samsung logo (side note: The music clip that playes when the logo gets outlined by the blue circle does not play completly, the last few moments are cut), after waiting for quite some time I thought I just go back to odin and install the stock firmware again. Sadly this only got me to the Samsung logo again.
Now I tried quite a few things...
I installed another stock version (Instead of the german one, i used one from luxembourgh)
I tried to install 4.2.2 again
The last thing I tried was to install the recovery menu from here (http://forum.xda-developers.com/showthread.php?t=2442915), so here is something that could be interessting. I tried to do a Factory reset before trying to reinstall the stock firmware, which worked only partially, I could not mount /config, which he wanted to do to delete it I guess.
When I tried to manually mount /config it would also fail. (Not sure if thats relevant, but its the only thing that did not worked as expected)
So, everything I tried, with factory reset and stuff ended in a stuck at the Samsung logo. In one case (not sure what combination of stuff) I got in the bootloop (Galaxy Tab 3 -> Restart -> Galaxy Tab 3 -> Restart), in a rare case I just got stuck at Galaxy Tab 3, and in most of the cases I got stuck at Samsung logo (Start -> Galaxy Tab 3 -> Samsung).
So I hope somebody can help me, since Id rather not buy a new tablet only because google thought it was a cool idea to prevent apps from writing on ext SD Card, and me ****ing something up in the flash process.
My Tablet is a Galaxy Tab 3 10.1 (GT-P5200) and at the moment with the 4.4.2 build "P5200XXUBOB1_P5200DBTBOB1_P5200XXUBNK1" (atleast thats the filename of the stock firmware im using, downloaded from http://www.sammobile.com/firmwares/download/43847/P5200XXUBOB1_P5200DBTBOB1_DBT/), I used Odin 3.07 and Odin 3.09.
I can access the Odin/Download mode, the build in recovery mode, and could use the TWRP recovery mode if I were to install it with Odin.
I still didnt solve it, every help would be greatly appreciated, I really dont want a paper weight in tablet format
Bump
I was given a Galaxy Tab S by a relative who works in a cell phone store. It was a demo device, and it had demo mode enabled. I initially attempted to reboot into recovery and do a wipe from there, but an error came up informing me that "MDM" had blocked this option (I assume MDM to mean manufacturer demo mode). The tablet was still working at this point, so I rebooted and got the exact model number, SM-T700. I googled for a bit and found the recommendation to be to reinstall the firmware. I've done a lot of ODIN flashes before, so I downloaded the correct firmware from the official firmware post here on XDA, rebooted to download mode, and flashed it without issues.
After 30 minutes, the tablet still just showed the Samsung boot screen. I did a hard reboot with volume up + power, and left it. After another 30 minutes, it still didn't show anything. I rebooted to download mode and tried flashing again. Same result. I rebooted to recovery and tried to wipe the device from there. MDM block.
After more searching, I decided to use the PIT file and the firmware file in ODIN. I've had to use PIT files a couple times before, so I was very careful in checking to ensure I had the correct one. I am very confident I did. I flashed that, and still the tablet would not boot.
I then decided to install TWRP and see if I could wipe from there. TWRP gave me some useful information: it returned that it could not mount any of the partitions on the device. 'could not mount /system', 'could not mount /data', etc.
I've done a lot of googling and reading since then, but I can't seem to find anybody else with the result. The closest thing I can find is a similar situation on some ASUS tablets, but the solution would definitely not work here. The only other thing I can find is people recommending to flash the PIT file, which I have no tried a second time and still does not work.
Does anybody have any suggestions? I don't know what else to do.
You didn't need the pit file, so forget about that.
The first thing you should have done is disable the reactivation lock.
Then flash the stock firmware, after that immediately boot into recovery and factory reset.
I would reflash the stock KitKat firmware and immediately boot into recovery after the flash and wipe data/reset
Ensure that during the flashing process there are no errors.
Updating, I got it figured out.
I tried 3 different firmwares, all of which flashed with no errors but did not work. 2 were KitKat, one was lollipop. I tried a fourth firmware (a Korean one from sammobile on lollipop) and it flashed exactly the same as all of the others, but this time it worked. I have no idea what was different with this firmware compared to the other three, but it worked, and I'm happy.
Activation lock cannot be disabled via the demo mode software on Samsung devices (unless there is a method of doing so I am unaware of), so that wasn't an option. I was unable to get the stock recovery to allow a factory reset. Teamwin recovery did allow a factory reset.
Either way, its working now.
I've searched, I've tried but to no avail have I been able to fix my poor note 8..and I'm hoping someone can help!
I HAD a stock 4.4.2 Note 8 (AT&T version I-467) running, and I went with the Kingroot method to root. The device rooted but ran like a dog, and in my infinite wisdom did a wipe/reset to see if that would help.
Now here is where I stand:
1) The device boots to a screen saying unauthorized firmware
2) I can get to download mode (power+vol. down+Home)
3) I can NOT get to the screen with (power+col. up+Home)
I have tried Kies, and it won't take the serial number/model number, and Odin can only seem to flash the boot loaders. I have tried 4 different ROM's from samsung (with different international codes), and none of them are able to update the system (they all fail at about 90%). I've tried the all in one toolkit, and since I can't enable USB debugging at this point, it never recognizes the device as attached.
I've tried manually flashing with Odin TWRP, Phils, and stock recovery,(in the hopes of getting one to take so I could load a new ROM from SD card) and they all fail as well.
When I split any of the system images I can load a boot loader file from them, and it succeeds, but everything else fails.
Can anyone point me in the right direction, or am I completely hosed?
Sparkinman said:
I've searched, I've tried but to no avail have I been able to fix my poor note 8..and I'm hoping someone can help!
I HAD a stock 4.4.2 Note 8 (AT&T version I-467) running, and I went with the Kingroot method to root. The device rooted but ran like a dog, and in my infinite wisdom did a wipe/reset to see if that would help.
Now here is where I stand:
1) The device boots to a screen saying unauthorized firmware
2) I can get to download mode (power+vol. down+Home)
3) I can NOT get to the screen with (power+col. up+Home)
I have tried Kies, and it won't take the serial number/model number, and Odin can only seem to flash the boot loaders. I have tried 4 different ROM's from samsung (with different international codes), and none of them are able to update the system (they all fail at about 90%). I've tried the all in one toolkit, and since I can't enable USB debugging at this point, it never recognizes the device as attached.
I've tried manually flashing with Odin TWRP, Phils, and stock recovery,(in the hopes of getting one to take so I could load a new ROM from SD card) and they all fail as well.
When I split any of the system images I can load a boot loader file from them, and it succeeds, but everything else fails.
Can anyone point me in the right direction, or am I completely hosed?
Click to expand...
Click to collapse
+1 on that, I'm stuck in an exact same situation. No help from Samsung either. After rooting with Kingroot my tab started acting like crazy with flickering screen and random reboots, did exactly like you did.
There are many with similar issue and as per my research most of them have given up. Getting a system image dump from a rooted tab running 4.4.2 might be the only way out. Unless of course Samsung/AT&T decides to release full odin flashable image.
I was in a similar situation from trying to fix a eff problem and took my sgh-i467 to a Samsung Experience Center located in many Best Buys and they fixed it free of charge. They were not able to fix my issue with a corrupted EFF file that is keeping my 4G from working though as I had hoped. If you have a Best Buy around with the Samsung Kiosk in it I would give it a try. I ended up trying a few different ones to fix the eff issue and some of the employees at the Samsung centers were about as smart as a head of cabbage (they laughed at me when I said my Note 8 was the issue and said "you can't have a Note 8 the Note 5 just came out") but some were at least helpful and listened when I told them they have the tools to fix my tab (reflash it back to life) and they did. Hopefully they can help you.
man Im in the same exact situation.. And I cant seem to find any help anywhere. I cant locate a stock 4.4.2 kit kat odin flashable file anywhere for the n5120
Sparkinman said:
I've searched, I've tried but to no avail have I been able to fix my poor note 8..and I'm hoping someone can help!
I HAD a stock 4.4.2 Note 8 (AT&T version I-467) running, and I went with the Kingroot method to root. The device rooted but ran like a dog, and in my infinite wisdom did a wipe/reset to see if that would help.
Now here is where I stand:
1) The device boots to a screen saying unauthorized firmware
2) I can get to download mode (power+vol. down+Home)
3) I can NOT get to the screen with (power+col. up+Home)
I have tried Kies, and it won't take the serial number/model number, and Odin can only seem to flash the boot loaders. I have tried 4 different ROM's from samsung (with different international codes), and none of them are able to update the system (they all fail at about 90%). I've tried the all in one toolkit, and since I can't enable USB debugging at this point, it never recognizes the device as attached.
I've tried manually flashing with Odin TWRP, Phils, and stock recovery,(in the hopes of getting one to take so I could load a new ROM from SD card) and they all fail as well.
When I split any of the system images I can load a boot loader file from them, and it succeeds, but everything else fails.
Can anyone point me in the right direction, or am I completely hosed?
Click to expand...
Click to collapse
please help me i need de 4 files repair from this tablet
Try the forum thread started by djjiz, https://forum.xda-developers.com/galaxy-note-8-0/help/i467-4-4-2-t3537302... He posted the files and yes I was able to bring back my previously bricked AT&T Note 8.
Hello!
Few days ago i found my Samsung Tab 3, and decided to charge it and biit it up.
It got stuck on Samsung logo when i booted it.
So i did a factory reset using the recovery mode.
After i did that the device booted up. with lots of errors.
I was on the setup screen for my device and these errors appeard and said like core has stopped working and every like preinstalled app on my samsung device aswell (NAME has stopped working). So i was not able to fullfill the setup of my device.
I read about it online and a firmware upgrade could fix the problem ( Like the easiest way i read )
So i did some googling and downloaded Odin and a firmware. Followed a guide and did everything right. BUT the process faild like 8min into the flash.
And now my device is stuck on "download mode" but with the error "Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again."
I cant get the phone to turn off, nor get into recovery mode or anything else. I tried flash again but no luck.
I also tried another firmware i found. still same problem.
How do i fix this and how can i use my samsung tab 3 again.
WHen i bought it years ago i never really used it. So it's in "new shape" and has never really been used. And now i wanna give it to my little sister for some kids games to play at Xmas.
I hope we can solve this problem.
Thanks in advance
Regards
Timmie
Hyldran0 said:
Hello!
Few days ago i found my Samsung Tab 3, and decided to charge it and biit it up.
It got stuck on Samsung logo when i booted it.
So i did a factory reset using the recovery mode.
After i did that the device booted up. with lots of errors.
I was on the setup screen for my device and these errors appeard and said like core has stopped working and every like preinstalled app on my samsung device aswell (NAME has stopped working). So i was not able to fullfill the setup of my device.
I read about it online and a firmware upgrade could fix the problem ( Like the easiest way i read )
So i did some googling and downloaded Odin and a firmware. Followed a guide and did everything right. BUT the process faild like 8min into the flash.
And now my device is stuck on "download mode" but with the error "Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again."
I cant get the phone to turn off, nor get into recovery mode or anything else. I tried flash again but no luck.
I also tried another firmware i found. still same problem.
How do i fix this and how can i use my samsung tab 3 again.
WHen i bought it years ago i never really used it. So it's in "new shape" and has never really been used. And now i wanna give it to my little sister for some kids games to play at Xmas.
I hope we can solve this problem.
Thanks in advance
Regards
Timmie
Click to expand...
Click to collapse
That depends on various things, such as the Android version, kernel and change ID. Than also the Odin version you've used and/or the settings during the attempt of flashing. I found that using the wrong Odin version on a particular Android version, that may prevent the flash of being successfull. B.t.w, did you format both user and cache partition while trying to reset to factory default?
xdausernl said:
That depends on various things, such as the Android version, kernel and change ID. Than also the Odin version you've used and/or the settings during the attempt of flashing. I found that using the wrong Odin version on a particular Android version, that may prevent the flash of being successfull. B.t.w, did you format both user and cache partition while trying to reset to factory default?
Click to expand...
Click to collapse
Yeah, I've found out what Odin version to use that worked for others. I've downloaded lots of different firmwares and such and tried. ALL fails.
When i did a factory reset i also cleared cash and user.
Now i cant even turn off the damn thing. If i charge it up and start, it just goes directly to the screen where it says "Firmware upgrade encountered an issue" and if i try to turn it off, it just reboots and goes back. And i cant even return to factory reset page.
I think that my Micro-USB cable might not work for this, or is that a thing? Do i need a good cable from PC to Phone for this? Or does any cable work?
I just want this tab to work. been trying for weeks.
Thanks for your reply. I hope we can sort this out.
Hyldran0 said:
Yeah, I've found out what Odin version to use that worked for others. I've downloaded lots of different firmwares and such and tried. ALL fails.
When i did a factory reset i also cleared cash and user.
Now i cant even turn off the damn thing. If i charge it up and start, it just goes directly to the screen where it says "Firmware upgrade encountered an issue" and if i try to turn it off, it just reboots and goes back. And i cant even return to factory reset page.
I think that my Micro-USB cable might not work for this, or is that a thing? Do i need a good cable from PC to Phone for this? Or does any cable work?
I just want this tab to work. been trying for weeks.
Thanks for your reply. I hope we can sort this out.
Click to expand...
Click to collapse
It is quite easy to turn the device off, for that to happen you have to press and hold the on/off button. You'll see that the device will shutdown and try to reboot and then finally shuts down again and stay off, then release the on/off button.
Are you sure trying to flash the correct firmware with correct changes, etc??
Please share with us the device and Android version, as well as the stock ROM version with changes you're trying to flash.
Put (copy and paste) the output of Odin below.
Another way to get the firmware flashed is by using Heimdall, but for that to happen you first need to rename the extension of the stock ROM (remove .md5 and leave .tar) and than extract all seperate pieces that are contained within the stock ROM.
All those extracted pieces from the stock ROM you have to upload seperately onto Heimdall and try to flash them to your tablet, one by one.
Heimdall you'll find 'here' or use FWUL instead which has Heimdall pre installed, download is to be found 'here' and install it on a USB medium a stick, to put FWUL onto USB, use Balena-Etcher and the download is to be found 'here'.
Micro USB cable does work, but if you're unsure, try another one and make sure using the correct drivers too.
Using Odin, make sure the tablet is recognised and 'connected' in Odin, also make sure 'repartitioning' is unchecked.
If you've used the wrong Odin version, flashing will fail!
You have Discord by any chance?
If so, please add me @Hyldran0#8832
Thank you for you time man!
Hyldran0 said:
You have Discord by any chance?
If so, please add me @Hyldran0#8832
Thank you for you time man!
Click to expand...
Click to collapse
You're welcome.
Hi, complete novice here, does anyone know where I can get a working Firmware for my Tab 3 v7 (SM-210)?
I have searched through various forum articles here, and tried to install with several builds but none will install. The only one that gets anywhere near is the JASBR build by gr8nole. It appears to install, but on restart, the TAB just sits on the "Samsung Tab3" start screen.
I read that I may need to flash the firmware 4.4.4 (Kit Kat), but can't find it!
The unit is not totally bricked (yet), as I can run TWRP 2.8, with which I created a backup of the original build, but when I try to restore the backup, it fails at just over 31%.
Can anyone help please?