[Q] No response Soft Brick - Sony Xperia S, Acro S, Ion

Hi!
Yesterday I want to install new ROM, but while I was doing it my mobile turned off and didn't want to wake up. Totally no respone, no LED when plug in to charger, no reaction on any buttons. I made a recovery but I can't restore it, because I can't power on my phone. I tried to flash new clear, stock ROM, but when i plug in XS to PC, when flashtool ask for it i got this log:
Code:
05/048/2015 19:48:19 - INFO - Device connected with USB debugging off
05/048/2015 19:48:19 - INFO - For 2011 devices line, be sure you are not in MTP mode
I think I had USB Debugging on (I install CWM before install ROM), but now I can't check it or change it, because I have a brick
I reset my phone just like was written in THIS thread, when the RED LED appear i prepare my flashtool to flash and then plug in my phone to PC, but then nothing happend and RED LED appear again. Flashtool didn't see my phone.
After few minutes pluged in charger RED LED disapear and back to begining.
There are any solution to fix my phone?

Related

[Q] Bricked Sony Xperia S - Help a noob out!

Hi all,
The wi-fi connectivity on my Sony Xperia S died a few days ago and it's been irritating me so I decided to root and upgrade to JB to see if that would sort it. Unlocked the bootloader, no problem. Rooted the phone, no problem. But then CWM couldn't identify my device and wouldn't install Recovery. I decided installed Flashtool and flashed a stock kernel, and now it seems like I have bricked the phone.
When I boot I get the Sony splash, and the Fastboot (blue) LED which then goes out leaving just the Sony splash. Pressing the volume keys does nothing during Fastboot. I can do a hard reset and get the three vibrations, but the boot loop is just the same when I power on again. In this state Flashtool says the following:
1/039/2013 14:39:48 - INFO - Device connected in flash mode
11/040/2013 14:40:32 - INFO - Device disconnected
11/040/2013 14:40:37 - ERROR - Drivers need to be installed for connected device.
11/040/2013 14:40:37 - ERROR - You can find them in the drivers folder of Flashtool.
Naturally trying to install the drivers does nothing.
Anyone got any suggestions? I really don't want to have to fork out for a new phone!
Cheers.
Make sure you have closed PCC & SUS.
Then try to flash again.
As cities516 has said, first make sure that all those Sony services and update programs are completely shut (be sure to check the status bar near the time and date too). When you power on your phone, the blue led blinks for some time and then fades away. This blue led does not indicate that you are in fastboot mode. So here is what you must do:-
1) Press and hold the volume up + power button until you get 3 vibrations.
2) DO NOT START THE PHONE.
3) Prepare flashtool to flash the stock ics ftf file
4) When it prompts you to connect your phone, hold the volume down key and connect the USB cable.
5) A green led should light up and the flashing process should begin.
6) Once the flashing is complete, disconnect the phone and turn it on normally.
abcdjdj said:
As cities516 has said, first make sure that all those Sony services and update programs are completely shut (be sure to check the status bar near the time and date too). When you power on your phone, the blue led blinks for some time and then fades away. This blue led does not indicate that you are in fastboot mode. So here is what you must do:-
1) Press and hold the volume up + power button until you get 3 vibrations.
2) DO NOT START THE PHONE.
3) Prepare flashtool to flash the stock ics ftf file
4) When it prompts you to connect your phone, hold the volume down key and connect the USB cable.
5) A green led should light up and the flashing process should begin.
6) Once the flashing is complete, disconnect the phone and turn it on normally.
Click to expand...
Click to collapse
That's great stuff, thanks. All working now! Although I do feel like a moron, I hadn't realised that the PCC was open in the system tray!

[ Q ] Xperia Pro Frozen USB / Black Screen

Hey guys i hope someone can help me out : )
Problem:
I froze some system apps on my xperia pro including mtp (the one that you need for the usb to connect to the computer)?!
well then i was using the phone like regularly and it suddenly froze.
Rebooted the phone ..black screen , the phone is booting normally but i cant see a thing of course.
Fastboot / Flash mode
With flashtool It says its connecting but then i get an error
With the cmd fastboot method its just stating "waiting for device" and when i connect it in fastboot mode nothing is happening just windows telling me thats something wrong with the usb connection and it wont work.
When the phone is turned on and connected to the computer i can see it listed in the device manager as mk16i
if that is relevant
Thanks for reading.
problem 1 : is your phone hardware qwerty button light up when you turn it on and dim when wait a few second? if similiar like that maybe you need to replace the flex cable
problem 2 : try reinstall your phone's driver and make sure you connect the phone in fastboot mode with blue notification led light up.

[Q] Phone won't turned on

Hi
I'm using Windows 7 64 bit, flashtool version 0.6.9.1
Here is my device info before the tragedy D:
ROM : Gin2JB (i forget the version)
Kernel : Lupus kernel (again forget the version)
I don't know what happen but my phone won't turned on D: when i press the power button it's vibrating, it even can go to the flashmode and fastboot mode, but it just wont show anything on screen D: is it my screen or what?
i already try to turn it on and wait for a while, so the phone can load and I try to call my own number but i can't, it's not connected D:
i think it's a little strange because it's happening when i'm reading a Visual Novel via VNDS, then i decided to take a break, and put the screen off by pressing the power button, then i try to turn it on again, usually when i try to turn on the screen again, it's lagging a little and the screen turned on normally , but the this time only the sound playing and *pop* the phone turned off completely! and then i try to turn on the phone but it won't D: i pull out the battery and turn it on again, and still it won't turned on D:
I even try to flash a .ftf file R800i_4.0.2.A.0.42_Generic.ftf (Here is the MD5 in case i flash a broken .ftf MD5 : 317FCA41566A2FE8331B670087DB015F)
after flashing i try to turn it on again but no luck D:
And if i try to pull out the battery and turn it on like normal and wait for a while (So if it's really the screen problem maybe it's load up to normal state) then try to plug it to the computer (Note : The memory card is not detected), the flashtool log show like this :
INFO - Device connected with USB debugging off
INFO - For 2011 devices line, be sure you are not in MTP mode
INFO - Device disconnected <--- I'm not unpluging my phone but it's disconnected automatically! and windows keep installing a new driver for MTP USB Device! right after the install for new driver fail, the "Device disconnected" message show up then it's connected automatically again and then it's doing same thing again and again D:
So any suggestion or idea what happen to my phone? D: is it really the screen? or the software? or anything else maybe??? if you need more info regarding my problem i'll be happy to tell you
sorry if my English is baaad :silly: not my mother tongue~~~
harunakaze said:
Hi
I'm using Windows 7 64 bit, flashtool version 0.6.9.1
Here is my device info before the tragedy D:
ROM : Gin2JB (i forget the version)
Kernel : Lupus kernel (again forget the version)
I don't know what happen but my phone won't turned on D: when i press the power button it's vibrating, it even can go to the flashmode and fastboot mode, but it just wont show anything on screen D: is it my screen or what?
i already try to turn it on and wait for a while, so the phone can load and I try to call my own number but i can't, it's not connected D:
i think it's a little strange because it's happening when i'm reading a Visual Novel via VNDS, then i decided to take a break, and put the screen off by pressing the power button, then i try to turn it on again, usually when i try to turn on the screen again, it's lagging a little and the screen turned on normally , but the this time only the sound playing and *pop* the phone turned off completely! and then i try to turn on the phone but it won't D: i pull out the battery and turn it on again, and still it won't turned on D:
I even try to flash a .ftf file R800i_4.0.2.A.0.42_Generic.ftf (Here is the MD5 in case i flash a broken .ftf MD5 : 317FCA41566A2FE8331B670087DB015F)
after flashing i try to turn it on again but no luck D:
And if i try to pull out the battery and turn it on like normal and wait for a while (So if it's really the screen problem maybe it's load up to normal state) then try to plug it to the computer (Note : The memory card is not detected), the flashtool log show like this :
INFO - Device connected with USB debugging off
INFO - For 2011 devices line, be sure you are not in MTP mode
INFO - Device disconnected <--- I'm not unpluging my phone but it's disconnected automatically! and windows keep installing a new driver for MTP USB Device! right after the install for new driver fail, the "Device disconnected" message show up then it's connected automatically again and then it's doing same thing again and again D:
So any suggestion or idea what happen to my phone? D: is it really the screen? or the software? or anything else maybe??? if you need more info regarding my problem i'll be happy to tell you
sorry if my English is baaad :silly: not my mother tongue~~~
Click to expand...
Click to collapse
Ok, as i understand it, you used to have gin2JB rom with Lupus kernel when you got black screen, then you flashed stock firmware.
Stock firmware don't have usb debbuging enabled by default and that is why you are getting "Device connected with USB debugging off"
You could try to update flashtool to see will that solve device disconnection problem.
Also, try different usb cable and even different usb port at motherboard (including back ports)
PC companion should work even with USB debugging disabled. If he recognize devise normaly, it is most likely hardware error. And maybe it's even flex slider cable fault (because it's weakest part of xPlay)
You try to open and close gamepad (and even some middle positions, when it's not even open or closed) when powering on. If you see screen working even for few seconds, then it's most likely damaged flex.
Ofcourse, maybe screen is dead, but chanse for that is lower (but not impossible)
Hi
Thanks for the reply, now i'm positive it's an hardware failure D: because i try to flash LuPuS_zeus_Stock-gB+iCsv7-full.img, and turn it on, and wait for a while, and *boom* pc companion detect my phone, well i don't know i should be happy or not D: (i'm still hoping it's a software failure though )
well i think the screen is dead, i try the "middle position" method but it wont work D:
well now any suggestion how to fix it?
I have another question though how can i use my android as modem (tethering) without configuring anything via phone (because it's half dead now), any info would be nice
As for flex cable, check out this thread from CriGiu about similar problem (to lazy to type it again ). It is not hard but you need special screwdriver
As for tethering, things can be little tricky. You need only to select tethering options in menu I know, with black screen it can be tricky
There is a way to see what is in phone but it is also... tricky
There is program for PC that can show what is on screen of phone, but it needs usb debugging enabled. Stock firmware don't have it enabled but most of custom roms have it. You "only" need to flash custom rom
Without working screen, it can be hard to install custom rom from recovery, but not impossible. I have an idea, you can try it if you want:
-download file in attachment and unpack it in some folder in PC
-download some recent GB or ICS custom rom frox XDA (for Play, ofcorse)
-make folder named "A1" on sdcard and place your rom into that folder (i guess you still can do that, most probably with pc companion if sd card is not mounted already)
-flash lupus ics/gb v7 kernel (skip if it's already flashed)
-power on phone in fastboot mode (or stay in it if you just flashed kernel)
-from unpacked folder double-click on file named "start.bat". It will erase all system and data on phone (but not sd card)
-disconnect and power on phone
-now, since it's lupus kernel, and since system is erased, it will boot directly to cwm recovery
-wait about 30sec or minute to make sure it is in recovery (since you can't see anything, we are guessing here)
-press menu button once (that should select "install zip" from recovery menu)
-press home button 4 (four) times (or maybe 5 or 6 , just in case ). Luckily, it will flash rom from first folder in sdcard (and that's why name "A1" for folder - use capital letter, it does matter)
-wait 5 minutes for rom to be flashed (just in case) and reboot (battery off/on)
-wait 10minutes rom to boot (maybe less, depends on rom)
-from attachment folder start file named "droidAtScreen-1.0.1.cmd" on pc (i do hope you have java installed on pc)
-if all goess well, you should see on PC screenshots of phone
-use dpad buttons to navigate to tethering options (and make sure to disable lockscreen - in case touchscreen is not working). If your touchscreen is working, it's flex cable 99% faulty :fingers-crossed:
If it doesn't work, you can flash stock firmware back so you can use pc companion
As i said, tricky, but not impossible :laugh:
Good luck :fingers-crossed:

[Q] Xperia Ion qhsusb_dload (Hard brick)

Hi guys! Sorry for my english. I have Xperia Ion (LT28h) . I installed the program Swapper 2. installed swap and rebooted the phone. now the phone is not included. Telephone defined as qhsusb_dload.
Afther I installed the driver from Flash Tool. instead of qhsusb dload become SEMC flash divice.
Log from Flash Tool
15/054/2014 11:54:45 - INFO - Device connected with USB debugging off
15/054/2014 11:54:45 - INFO - For 2011 devices line, be sure you are not in MTP mode
Click to expand...
Click to collapse
But no use. No green/blue does not light diod. Nо can enter in any mode.
I do not know what to do, Help please!
Nick_Holmes said:
Hi guys! Sorry for my english. I have Xperia Ion (LT28h) . I installed the program Swapper 2. installed swap and rebooted the phone. now the phone is not included. Telephone defined as qhsusb_dload.
Afther I installed the driver from Flash Tool. instead of qhsusb dload become SEMC flash divice.
Log from Flash Tool
But no use. No green/blue does not light diod. Nо can enter in any mode.
I do not know what to do, Help please!
Click to expand...
Click to collapse
i got the same problem have u success to works the phone again
any help guys please
Cheers
Swapper has a bad history of deleting the whole OS I've heard. It probably has messed with your bootloader. Can you enter flash/fastboot mode? And swapper only runs on kernels that support it. I doubt that we have any such kernels.
I think I have the same problem here. I already searched everywhere and I'm loosing my hopes. I'm trying to revive a Xperia Ion and this is what I get:
When I plug the phone in the wall charger the red led turns on for some minutes and then turns off, no green leds, my phone was in charger for months, changed charger and cable.
The same happens when I plug on PC, when the led turns off it is detected as "Somc flash device" in windows device manager and this shows in flashtool:
INFO - Device connected with USB debugging off
INFO - For 2011 devices line, be sure you are not in MTP mode
Nothing changes if I plug in pc with volume + or - pressed, it don't goes into fastboot or flashmode.
I hope you could help me. Thanks

acro s hard bricked

i got my acro s hard bricked
I used twrp for making a backup for the the stock firmware.
and then i installed the 5.0.1 the lollipop custom firmware
the link :http://forum.xda-developers.com/showthread.php?t=2799765
, but it was not rooted but somehow the recovery was working good .. i decided to restore the stock using the backup version which i made in the beginning coz the ROM was sucks. after finishing the loading it asked for restart and after that i got a blank screen and the following
-no response for charging
-no LED lights at all
-non of any combinations working (volume+ and power on , hard reset or volume+up+power on)
-access to fastboot or flashtool is denied
-no power on no vibrations
but after a day of charging an Orange LED appears but i waited for two more days till the LED disappeared
and tried the flashtool but all i got is "device connected but with debugging off"
i think the problem was using recovery with unrooted device but can't find a solution for that
any suggestions ??!!
Notes:
am too calm
am not panic ..
am not in hurry too
and it's not a big deal
i just want the device back in order to get my stuff from it that's why going to Sony service center is not an option coz they format the whole device
Similar here on st26i
On 4.4 Paranoidandroid I've got after a five days of use in one second a lot of force closes. From every app from the system. It was impossible to stop it, or make normal reboot, so I've hold Power + VolUp and waited till three vibrations. Then turn on the phone, normal vibration and SONY logo.
After that black screen. First with some backlight, after minutes phone backlight turn off.
Now:
- No response for Power button
- No response for Power+VolUp combination
- No charging LED
- System find only SEMC Flash Device
- Flashtool says Device Connected with USB Debugging off
- Combination Power+VolUp make connected device to disconnect and connect again as SEMC Flash Device
- Cant acces fastboot, dwonload mode.
smogf said:
Similar here on st26i
On 4.4 Paranoidandroid I've got after a five days of use in one second a lot of force closes. From every app from the system. It was impossible to stop it, or make normal reboot, so I've hold Power + VolUp and waited till three vibrations. Then turn on the phone, normal vibration and SONY logo.
After that black screen. First with some backlight, after minutes phone backlight turn off.
Now:
- No response for Power button
- No response for Power+VolUp combination
- No charging LED
- System find only SEMC Flash Device
- Flashtool says Device Connected with USB Debugging off
- Combination Power+VolUp make connected device to disconnect and connect again as SEMC Flash Device
- Cant acces fastboot, dwonload mode.
Click to expand...
Click to collapse
it seems like we stuck here
Yup.
Is there any windows/linux software for SONY devices like KDZ for LG phones? Which have an emergency flash option and, etc.???
/EDIT
So... I have read a little and I think (wchich I supposed before witout reading) boot is "dead".
I think it will be possibly to flash new boot with s1boot, but. I cannot find service manual for lt26i. Can anyone have it? Or can say where is the Test Point in this device?
makaom said:
i got my acro s hard bricked
I used twrp for making a backup for the the stock firmware.
and then i installed the 5.0.1 the lollipop custom firmware
the link :http://forum.xda-developers.com/showthread.php?t=2799765
, but it was not rooted but somehow the recovery was working good .. i decided to restore the stock using the backup version which i made in the beginning coz the ROM was sucks. after finishing the loading it asked for restart and after that i got a blank screen and the following
-no response for charging
-no LED lights at all
-non of any combinations working (volume+ and power on , hard reset or volume+up+power on)
-access to fastboot or flashtool is denied
-no power on no vibrations
but after a day of charging an Orange LED appears but i waited for two more days till the LED disappeared
and tried the flashtool but all i got is "device connected but with debugging off"
i think the problem was using recovery with unrooted device but can't find a solution for that
any suggestions ??!!
Notes:
am too calm
am not panic ..
am not in hurry too
and it's not a big deal
i just want the device back in order to get my stuff from it that's why going to Sony service center is not an option coz they format the whole device
Click to expand...
Click to collapse
Same situation, really need help from someone because its my only android phone right now.

Categories

Resources