I'd be really grateful for anyone who can help me. I could even pay a small reward if I can get this phone to work.
Factory restore/hard reset doesn't work. I press power to confirm, and it says "confirmed" or whatever the message is and stops there.
smaybe said:
guys if you are stuck but could go in download mode you have this solution :
http://forum.xda-developers.com/showpost.php?p=43772519&postcount=3
Click to expand...
Click to collapse
No such option in the current LG Mobile Support Tool.
When I start it, it checks for software and says I'm up to date.
It lists "Software version: _" which doesn't seem right.
LGFlashTool:
Fails for me every time.
New USB cord on back ports, have tried different ports.
It gives a PID, correct model and IMEI.
Checks Milky, DLL, bin CRC. I've re-downloaded the bin anyway.
When the phone is reconnected, it shows on COM41 and flashes.
System, tz, boot, rpm, aboot, sbl3/2/1, modem.
Then it says Factory Reset and Reboot sleep time
It then reboots and seems to fail recognizing the phone afterward. It gives error F0000002 and says "Download FAIL!!" at 95 or 99%.
LG Flash Tool 2014:
From what I gathered, there IS NO KDZ for the e980.
It was recommended to me to flash the Central America e980H KDZ to possibly restore the bootloader/recovery.
This gets to about 95% and then the phone reboots to the LG logo and hangs. After several minutes of waiting, it says "Upgrade stopped due to an error" and prompts me to try again after removing the battery. This just happens over and over again.
Thanks in advance for any help!
I've flashed the g, k and p tots. One won't even allow me to enter factory restore. The other two just hang if I do, or hang at the LG logo if I don't.
I've also tried following the instructions to make a restore microSD and tried another pre-built one, but it doesn't seem to boot/restore from the card.
What options do I have left? Can anyone help? Thanks.
fierogt42 said:
I've flashed the g, k and p tots. One won't even allow me to enter factory restore. The other two just hang if I do, or hang at the LG logo if I don't.
I've also tried following the instructions to make a restore microSD and tried another pre-built one, but it doesn't seem to boot/restore from the card.
What options do I have left? Can anyone help? Thanks.
Click to expand...
Click to collapse
Refer hyelton's guide for getting stock rom on our phone. Use the flash tool provided in the thread and probably you will be good to go.
Sent from my LG-E980
I assume you didn't read the post? Thanks, but that's the first thing I tried, with every compatible .tot and kdz that exists and every LG flashing tool available. I'm not a newb to rooting and unbricking phones. No offense, and I do appreciate that someone finally replied, but if I wanted someone to tell me to RTFM, use the search, or read the stickies I wouldn't have wasted peoples' time with a post and all of the details of what I tried.
I assume at this point that it's pretty well screwed and nothing short of a JTAG will resurrect it, if that even will. I'm leaning toward a hardware fault or something lower level than any firmware/baseband flashing will touch. :/
How did you bricked your phone the first time? Because if you can enter the download mode to use the flash tool, it shouldn't require you to load from the SD card or use jtag to repair the device. Those are the techniques for the device that's completely dead.
Right, but I tried flashing all of the US .tot images as well ask a kdz for central america. I tried flashing using different tools. I have tried literally every possible way that I can find, and it has the same strange problem of hanging at the LG logo and at the "hard reset" factory recovery screen.
It was brought to me as having a "software issue" from a bad update. I wasn't able to determine whether that was factory OTA or flashing a rom, but this thing apparently has some issues that a flash to 100% factory will not resolve. Either it's unable to flash itself through download mode, or it flashes and they all have the same problem afterward. I re-downloaded and re-checked the md5s over and over again. Tried different ports and cables, despite never having had a problem before on this computer with a dozen other devices, several times each.
I'm fairly certain there's a low level firmware or hardware fault so I've ditched the phone. No purpose in continuing the thread unless someone else has the same issue. And in that case, I cannot help without obtaining some kind of adb or fastboot.
Thanks for the replies all the same.
May be the motherboard is the problem?
Try charging
Sent from my LG-E988 using XDA Free mobile app
same boat as you any help ?
fierogt42 said:
I'd be really grateful for anyone who can help me. I could even pay a small reward if I can get this phone to work.
Factory restore/hard reset doesn't work. I press power to confirm, and it says "confirmed" or whatever the message is and stops there.
No such option in the current LG Mobile Support Tool.
When I start it, it checks for software and says I'm up to date.
It lists "Software version: _" which doesn't seem right.
LGFlashTool:
Fails for me every time.
New USB cord on back ports, have tried different ports.
It gives a PID, correct model and IMEI.
Checks Milky, DLL, bin CRC. I've re-downloaded the bin anyway.
When the phone is reconnected, it shows on COM41 and flashes.
System, tz, boot, rpm, aboot, sbl3/2/1, modem.
Then it says Factory Reset and Reboot sleep time
It then reboots and seems to fail recognizing the phone afterward. It gives error F0000002 and says "Download FAIL!!" at 95 or 99%.
LG Flash Tool 2014:
From what I gathered, there IS NO KDZ for the e980.
It was recommended to me to flash the Central America e980H KDZ to possibly restore the bootloader/recovery.
This gets to about 95% and then the phone reboots to the LG logo and hangs. After several minutes of waiting, it says "Upgrade stopped due to an error" and prompts me to try again after removing the battery. This just happens over and over again.
Thanks in advance for any help!
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=2438088
Stock kdz here
If you ever flashed KDZ to your e980, LGFlashTool will not allow you to flash TOT files by means of Download Mode, because there's a check for device model which doesn't match (that info afaik is based on SBL3 content).
If you have Dowload Mode functioning: (1) flash any KDZ (preferably for the same size of memory, 32GB) and you will have a working phone; (2) root the system; (3) replace boot partitions by those from native e980 installation (all together) by means of dd command; (4) flash native TOT file from Download Mode.
Be very cautious while on p.3. If you do this wrong, you will have a hard brick which will require special tools to fix it.
Related
Hey Guys,
First post and i already got a problem because i messed up very much
I used to have Cyanogenmod 11 on my Optimus G, but i got several crashes and i wasnt completely fine with it so i wanted to try something new. So i updated my bootloader from CWM to TWRP and wanted to flash Artmod 5.2 Rom. I was a bit fast with my wiping, so i accidentally wiped the whole phone, so that everything was gone: Cyanogenmod, new Artmod rom i wanted to flash just everything.
I read a bit and thought it shouldnt be a problem then to just sideload the new rom, which i tried to do. I used adb sideload to put Artmod on the phone, everything was fine, flashing went through but i got stuck at the LG boot logo at the start of the phone. I waited like 30 minutes and nothing did change, so i thought something was not right.
I then just wanted to go back to cyanogenmod, tried to flash that through the adb sideload procedure but i got an error which said "error executing updater binary in zip 'tmp/sideload.zip'".
I was kinda thinking something really messed up so i tried to revert the phone to stock rom with the correct KDZ file i searched with the tool linked in the FAQ, everything downloaded but when i tried to flash the KDZ it gave me an error like this:
"12:03:59 Launching SW update
12:03:59 Unpacking KDZ
12:05:10 KDZ file extracted
12:05:11 Extract file error
12:05:13
===FINISH===="
So i searched the forums again and noticed that it should be a problem with the KDZ updater tool because the KDZ file was too big to get flashed properly. I wanted to try the LG Flash Tool 2014 then which is provided here in the forums and should work, it extracted the KDZ file, then opened the LG Mobile Support Tool to flash the file on the phone but there i start to get errors again, it either said that i am already on the correct up to date software version or that i need to disconnect the USB cable, remove the battery, insert it again, restart and try again.
I used several tools for that, i even tried it with an offline method that i found in a german forum, but every method got me the same errors, so i couldn't even go back to stock anymore.
I once tried to flash Cyanogenmod then again when i realized that the error message also told me "This Rom is for a "E975", this is a "GEE"" which i did not completely understand because it should be the total same? I edited the Updater-Script in the Zip file of the rom then and removed the part where it checks for that (1st line actually), then the rom did flash properly, phone started to boot (Cyanogenmod Boot Logo was shown) but when the boot was over i got the message:
"Type Password to Decrypt Storage" with a keyboard to enter the password. (I did never set up any password for that).
Now i am completely confused what i can do the recover my phone, either to stock or just to another rom, every method i tried did not work and i dont have any other ideas.
I can go into Fastboot, Recovery and Downloadmode, but when i tried to wipe again in Recovery it says that it cant mount my data mount point (probably because the storage is encrypted).
Somebody told me to do a hard reset with the keys "Volume down and power" which i tired several times, but everything i get is just the Google boot logo and then happens nothing or i get the Google logo, then the LG logo but after that i get stuck again, I cant seem to go into the "Hard Reset" menu which i should get into with that keys.
Anybody can help me what I could try or got a solution for this? I would be very thankful. I don't wanna loose my phone
Astarooth said:
First post and i already got a problem because i messed up very much
Click to expand...
Click to collapse
Don't worry, that's pretty standard scenario for the first post...
I wanted to try the LG Flash Tool 2014 then which is provided here in the forums and should work, it extracted the KDZ file, then opened the LG Mobile Support Tool to flash the file on the phone but there i start to get errors again, it either said that i am already on the correct up to date software version or that i need to disconnect the USB cable, remove the battery, insert it again, restart and try again.
Click to expand...
Click to collapse
Flash Tool 2014 works great for me every time, so try it again. Make sure you disconnect from the Internet before running it (yank out your LAN cable, or disable your WiFi), so it doesn't attempt to connect to LG servers. And don't forget to put your KDZ file in the same directory with the tool. It should go through just fine. That's by far the easiest method to revert back to stock, to get you to a clean starting point.
"This Rom is for a "E975", this is a "GEE"" which i did not completely understand because it should be the total same?
Click to expand...
Click to collapse
Umm... No, they are not the same. E975 is "geehrc", and there is no such OEM ID as "gee". There are many different OG variants. For the cross-reference between the models and OEM IDs, you can look here. Generally, you should stick to the ROMs that are designed for your model, unless you know exactly what you are doing, when trying to flash a ROM from a different platform.
kt-Froggy said:
Don't worry, that's pretty standard scenario for the first post...
Flash Tool 2014 works great for me every time, so try it again. Make sure you disconnect from the Internet before running it (yank out your LAN cable, or disable your WiFi), so it doesn't attempt to connect to LG servers. And don't forget to put your KDZ file in the same directory with the tool. It should go through just fine. That's by far the easiest method to revert back to stock, to get you to a clean starting point.
Umm... No, they are not the same. E975 is "geehrc", and there is no such OEM ID as "gee". There are many different OG variants. For the cross-reference between the models and OEM IDs, you can look here. Generally, you should stick to the ROMs that are designed for your model, unless you know exactly what you are doing, when trying to flash a ROM from a different platform.
Click to expand...
Click to collapse
Well i tried Flash Tool 2014 again and seem to get the same error that wants me to disconnects as it stops at the same position like it always did, also doesn't matter if I am connected to the internet or not, everytime it doesn't run through. This time I couldn't even read the stuff that was written in the LG Mobile Support tool because it only shows "????".
Heres a Screenshot:
The settings i made should be the right ones I think, the phone does get recognized by the computer when i plug it in because of the sound that windows makes.
I clearly dont't know what I can try anymore...
And according to the roms: well i only used roms for the E975, which is exactly my phone model, thats why i was wondering about that error message i got
Artmod is for E975, the CM11 was for E975, i even tried Mokee rom but i always got same error messages...
Nobody got another idea? I really am confused because if i can enter downloadmode and recovery there should be a way to get my phone back working.
Anybody knows where i can get maybe some older KDZ Files to go to 4.1.2 Stock rom and try to flash these?
problem
Astarooth said:
Nobody got another idea? I really am confused because if i can enter downloadmode and recovery there should be a way to get my phone back working.
Anybody knows where i can get maybe some older KDZ Files to go to 4.1.2 Stock rom and try to flash these?
Click to expand...
Click to collapse
Contact me on [email protected] and ill help u over teamwiewer.
Astarooth said:
Well i tried Flash Tool 2014 again and seem to get the same error that wants me to disconnects as it stops at the same position like it always did, also doesn't matter if I am connected to the internet or not, everytime it doesn't run through. This time I couldn't even read the stuff that was written in the LG Mobile Support tool because it only shows "????".
Heres a Screenshot:
The settings i made should be the right ones I think, the phone does get recognized by the computer when i plug it in because of the sound that windows makes.
I clearly dont't know what I can try anymore...
Click to expand...
Click to collapse
I don't know why you are seeing "???", but here is a couple of things regarding the settings, based on your screenshot:
1. Type should be CDMA (yours is 3GQCT).
2. PhoneMode should be DIAG (yours is CS_EMERGENCY).
3. I would suggest using CSE Flash for a full format (you are using Normal Flash).
Remember, this is a hacked tool, so the settings might not make perfect sense, comparing to the original ones. Just try following the instructions in the OP of the Flash Tool 2014 thread. Like I said, works every time for me...
kt-Froggy said:
I don't know why you are seeing "???", but here is a couple of things regarding the settings, based on your screenshot:
1. Type should be CDMA (yours is 3GQCT).
2. PhoneMode should be DIAG (yours is CS_EMERGENCY).
3. I would suggest using CSE Flash for a full format (you are using Normal Flash).
Remember, this is a hacked tool, so the settings might not make perfect sense, comparing to the original ones. Just try following the instructions in the OP of the Flash Tool 2014 thread. Like I said, works every time for me...
Click to expand...
Click to collapse
I don't know why i see "???" also, but it didn't matter
I just tried the settings you told and used CSE Flash which worked out really well.
No i am back to 4.4.2 LG Stock rom. I think the root is gone now, but one thing i wanna ask is if my bootloader is still unlocked and custom recovery is still on it?
Anyway, thank you so so much! I appreciate your help! Thank you!
Astarooth said:
I don't know why i see "???" also, but it didn't matter
I just tried the settings you told and used CSE Flash which worked out really well.
No i am back to 4.4.2 LG Stock rom. I think the root is gone now, but one thing i wanna ask is if my bootloader is still unlocked and custom recovery is still on it?
Click to expand...
Click to collapse
Glad to hear you are back in business. After flashing KDZ, the root is definitely gone, your BL is locked, and the recovery is stock. You will need to do all the necessary steps again: root, unlock the BL and flash custom recovery.
Hello! I want to address my issue as clear as i can.
I have this stock LG G3 with android 5.0 LP (Lollipop) that worked really slow and buggy. So i decided to "Wipe the phone" and refurbish it, i thought following the steps of this guide would do the trick (http://forum.xda-developers.com/showthread.php?t=2785089)
I looked in my "Settings>About Phone>Software" on my phone, and it said i hade software version "20h-EUR-xx"
I downloaded LGUP and a ".kdz" that i thought would fit my phone. The KDZ i downloaded was "D85520h_00.kdz" as i saw this as the most suitable for my phone.
I then followed the steps "TO DO A FULL WIPE AND INSTALL MM" throughout.
(Sidenote: I didn't have Marshmallow when i started the flash. Could this be the problem? also: I think the KDZ i used in this flash is a LP (Lollipop) not a MM (Marshmallow), though i followed the guide steps that stated "TO GO BACK TO LP FROM MM".
Can someone confirm this for me? And could that be the reason for my problem?)
I opened LGUP as ADMIN, my phone was recognized instantly so i proceeded with clicking on the "..." under the tab for "FILE PATH" to open the browser. I was only enable to look for ".TOT" files though i had a ".KDZ" flash file. So i closed LGUP and restarted it, but NOW i checked the UPGRADE option instead of REFURBISH and once again browsed for my ".KDZ". Now i had the option to select my ".KDZ" file, so i selected it and then closed LGUP.
When i started the LGUP program again my ".KDZ" was set as the file path and REFURBISH was also checked. The BIN checkbox was also checked so i proceeded to start the flashing.
The flash went fast up to 8% and then it waited for my phone to restart, Once it had restarted it went straight up to 80% and went pretty slow up to 100% from there.
Everything seemed to have turned out Great! The LGUP program told me the flashing was done and said "click here" in the "STEP" tab where the "progress %" had been displayed.
I clicked where it said "DONE! Click here!" and just sat waiting for about 30 seconds.
But nothing seemed to happen...
i waited 10 more seconds and still nothing happening on the screen of my computer or the screen on my phone. So i picked the phone up and held in the power on button.
Nothing happened, so i held in both volume up and the power button, still nothing, i held all three buttons.... Still nothing, i pulled the cable out. nothing.
Then when i pulled the battery out and reinserted it the screen came to life, giving me a "secure booting error" and then the front led started flashing red and blue.
I NEED HELP WITH THE STEPS OF HOW TO GET MY PHONE BOOTED AND STARTED AGAIN!
THANK YOU in advance!
I have searched for someone that has the same problem but all i can find is solutions for slightly different phones with slightly different problems in one or the other way.
I can get the phone in "Download mode" if that is to any help. I don't know about Recovery mode at the time of writing!
As a sidenote: I don't know if i had usb debugging set on or off when i flashed the kdz.
ettla said:
Hello! I want to address my issue as clear as i can.
I have this stock LG G3 with android 5.0 LP (Lollipop) that worked really slow and buggy. So i decided to "Wipe the phone" and refurbish it, i thought following the steps of this guide would do the trick (http://forum.xda-developers.com/showthread.php?t=2785089)
I looked in my "Settings>About Phone>Software" on my phone, and it said i hade software version "20h-EUR-xx"
I downloaded LGUP and a ".kdz" that i thought would fit my phone. The KDZ i downloaded was "D85520h_00.kdz" as i saw this as the most suitable for my phone.
I then followed the steps "TO DO A FULL WIPE AND INSTALL MM" throughout.
(Sidenote: I didn't have Marshmallow when i started the flash. Could this be the problem? also: I think the KDZ i used in this flash is a LP (Lollipop) not a MM (Marshmallow), though i followed the guide steps that stated "TO GO BACK TO LP FROM MM".
Can someone confirm this for me? And could that be the reason for my problem?)
I opened LGUP as ADMIN, my phone was recognized instantly so i proceeded with clicking on the "..." under the tab for "FILE PATH" to open the browser. I was only enable to look for ".TOT" files though i had a ".KDZ" flash file. So i closed LGUP and restarted it, but NOW i checked the UPGRADE option instead of REFURBISH and once again browsed for my ".KDZ". Now i had the option to select my ".KDZ" file, so i selected it and then closed LGUP.
When i started the LGUP program again my ".KDZ" was set as the file path and REFURBISH was also checked. The BIN checkbox was also checked so i proceeded to start the flashing.
The flash went fast up to 8% and then it waited for my phone to restart, Once it had restarted it went straight up to 80% and went pretty slow up to 100% from there.
Everything seemed to have turned out Great! The LGUP program told me the flashing was done and said "click here" in the "STEP" tab where the "progress %" had been displayed.
I clicked where it said "DONE! Click here!" and just sat waiting for about 30 seconds.
But nothing seemed to happen...
i waited 10 more seconds and still nothing happening on the screen of my computer or the screen on my phone. So i picked the phone up and held in the power on button.
Nothing happened, so i held in both volume up and the power button, still nothing, i held all three buttons.... Still nothing, i pulled the cable out. nothing.
Then when i pulled the battery out and reinserted it the screen came to life, giving me a "secure booting error" and then the front led started flashing red and blue.
I NEED HELP WITH THE STEPS OF HOW TO GET MY PHONE BOOTED AND STARTED AGAIN!
THANK YOU in advance!
I have searched for someone that has the same problem but all i can find is solutions for slightly different phones with slightly different problems in one or the other way.
I can get the phone in "Download mode" if that is to any help. I don't know about Recovery mode at the time of writing!
As a sidenote: I don't know if i had usb debugging set on or off when i flashed the kdz.
Click to expand...
Click to collapse
What it your model number ? Are you sure that you have the international version (d855) ? Check it by removing the battery and looking next to the S/N . If you have the D855 model you should see LG-D855. I am asking this because you may have downloaded a kdz file for another model. And why use LGUP?...the best way is to use a custom recovery like TWRP (http://forum.xda-developers.com/lg-g3/orig-development/recovery-twrp-touch-recovery-2-8-2-0-t2966129) It is much easier to install roms with TWRP simply by flashing flashable zips.
ettla said:
Hello! I want to address my issue as clear as i can.
I have this stock LG G3 with android 5.0 LP (Lollipop) that worked really slow and buggy. So i decided to "Wipe the phone" and refurbish it, i thought following the steps of this guide would do the trick (http://forum.xda-developers.com/showthread.php?t=2785089)
I looked in my "Settings>About Phone>Software" on my phone, and it said i hade software version "20h-EUR-xx"
I downloaded LGUP and a ".kdz" that i thought would fit my phone. The KDZ i downloaded was "D85520h_00.kdz" as i saw this as the most suitable for my phone.
I then followed the steps "TO DO A FULL WIPE AND INSTALL MM" throughout.
(Sidenote: I didn't have Marshmallow when i started the flash. Could this be the problem? also: I think the KDZ i used in this flash is a LP (Lollipop) not a MM (Marshmallow), though i followed the guide steps that stated "TO GO BACK TO LP FROM MM".
Can someone confirm this for me? And could that be the reason for my problem?)
I opened LGUP as ADMIN, my phone was recognized instantly so i proceeded with clicking on the "..." under the tab for "FILE PATH" to open the browser. I was only enable to look for ".TOT" files though i had a ".KDZ" flash file. So i closed LGUP and restarted it, but NOW i checked the UPGRADE option instead of REFURBISH and once again browsed for my ".KDZ". Now i had the option to select my ".KDZ" file, so i selected it and then closed LGUP.
When i started the LGUP program again my ".KDZ" was set as the file path and REFURBISH was also checked. The BIN checkbox was also checked so i proceeded to start the flashing.
The flash went fast up to 8% and then it waited for my phone to restart, Once it had restarted it went straight up to 80% and went pretty slow up to 100% from there.
Everything seemed to have turned out Great! The LGUP program told me the flashing was done and said "click here" in the "STEP" tab where the "progress %" had been displayed.
I clicked where it said "DONE! Click here!" and just sat waiting for about 30 seconds.
But nothing seemed to happen...
i waited 10 more seconds and still nothing happening on the screen of my computer or the screen on my phone. So i picked the phone up and held in the power on button.
Nothing happened, so i held in both volume up and the power button, still nothing, i held all three buttons.... Still nothing, i pulled the cable out. nothing.
Then when i pulled the battery out and reinserted it the screen came to life, giving me a "secure booting error" and then the front led started flashing red and blue.
I NEED HELP WITH THE STEPS OF HOW TO GET MY PHONE BOOTED AND STARTED AGAIN!
THANK YOU in advance!
I have searched for someone that has the same problem but all i can find is solutions for slightly different phones with slightly different problems in one or the other way.
I can get the phone in "Download mode" if that is to any help. I don't know about Recovery mode at the time of writing!
As a sidenote: I don't know if i had usb debugging set on or off when i flashed the kdz.
Click to expand...
Click to collapse
Boot into download mode and follow this: http://forum.xda-developers.com/showthread.php?t=2785089
Try to use the TOT method, but if you really need the kdz you can try to download the kdz again and reflash the phone (use CSE flash because MM is a major update!).
Maybe it was a bad download or a bad flash.
George Malas said:
And why use LGUP?...the best way is to use a custom recovery like TWRP It is much easier to install roms with TWRP simply by flashing flashable zips.
Click to expand...
Click to collapse
People use LGUP to flash stock rom/recovery/modem/etc... and keep the bootloader locked while TWRP is for custom rom
George Malas said:
What it your model number ? Are you sure that you have the international version (d855) ? Check it by removing the battery and looking next to the S/N . If you have the D855 model you should see LG-D855. I am asking this because you may have downloaded a kdz file for another model. And why use LGUP?...the best way is to use a custom recovery like TWRP (http://forum.xda-developers.com/lg-g3/orig-development/recovery-twrp-touch-recovery-2-8-2-0-t2966129) It is much easier to install roms with TWRP simply by flashing flashable zips.
Click to expand...
Click to collapse
My model number is D855 yes, i already double checked that.
The KDZ i used was "D85520h_00.kdz" it seems to me that it was the right KDZ because of the first part in the filename "D855(20h_00.kdz)"
I used LGUP because it said in the guide i followed that LGUP could flash both TOT and KDZ, it seemed really easy too!
Thanks for helping and the tip about TWRP, i will try that later!
RapHaeL_4_4_4_ said:
Boot into download mode and follow this: http://forum.xda-developers.com/showthread.php?t=2785089
Try to use the TOT method, but if you really need the kdz you can try to download the kdz again and reflash the phone (use CSE flash because MM is a major update!).
Maybe it was a bad download or a bad flash.
Click to expand...
Click to collapse
I followed your advice to follow the guide. As i could not find a TOT file for my specific application and i already tried the LGUP program for flashing my "D85520h_00.kdz" KDZ. But this time i tried the KDZ method in download mode instead of using the TOT method and LGUP, and it worked!
The flash turned out good and my phone is fresh again, thanks!
Just curious, did you use this file from codefire with your LGUP?
http://downloads.codefi.re/autoprime/LG/LG_G3/LGUP_8974_DLL_Ver_0_5_CODEFIRE.MSI
Navuhodonosor said:
Just curious, did you use this file from codefire with your LGUP?
Click to expand...
Click to collapse
No i did not use the 8974 dll from codefire. I used the dll that was supplied with LGUP in the guide, i think it was the 8994 dll
Edit: The LGUP method did not work for me with the 8994 dll... So maybe it could have worked with the 8974?
Either that or i had a faulty kdz on my first try
ettla said:
No i did not use the 8974 dll from codefire. I used the dll that was supplied with LGUP in the guide, i think it was the 8994 dll
Edit: The LGUP method did not work for me with the 8994 dll... So maybe it could have worked with the 8974?
Either that or i had a faulty kdz on my first try
Click to expand...
Click to collapse
I think that the .dll that came with LGUP is for G4 so codefire provided G3 version. That was probably all of your problems.
Navuhodonosor said:
I think that the .dll that came with LGUP is for G4 so codefire provided G3 version. That was probably all of your problems.
Click to expand...
Click to collapse
Wow! really? that would explain it :laugh:
I don't know what's going on with this thing, but basically the only mode I can get into is Download Mode, and if I try to flash something using LGFlashTool or LGUP, it stops at 6% and says that communication failed with the phone. I'm not sure what to do next, as I've tried different methods of flashing it, and different flashing programs, and keep getting the same result.
Okay, just to give a bit more info:
When I first got it, I tried to root the phone to install TWMP, but rooting didn't work (not a surprise). For some reason, it DID overwrite my recovery partition, but without the rooting I couldn't even get to it. So the phone itself at this point could only be put into Download mode and regular Android mode. I then tried flashing the stock Bell firmware onto the phone, to try and get it to go back to default. This worked, but it failed at 99% and when I tried to load it, it stuck at the Android Update screen (the one with the green Android robot and the blue bar showing progress), on all modes except Download Mode. Then, when I tried to flash another firmware onto it, flashing failed at 6% saying that it lost connection to the device, and it's been doing that for any attempt to do anything in Download Mode since. No other modes work; they all freeze on the Android Update screen.
I am having the same problem with my lg g3 i can get in twrp mode tho but there is 0mb in all my folders even external sd card wich has stock ROM but it won't read it, always seeing E: unable to mount /data /storage.. lg flash tool gets stuck at 6% like you & when i try adb flash it just stays at waiting for devices..
Yep, just had the same thing happen to me. Can get into TWRP, but can't mount anything, and trying to re-flash the device using Download Mode fails in the same way. Does yours claim it's the old Kitkat install as well?
Update: TWRP is claiming that /system, /data and /cache don't exist at all. The block devices are not listed in /dev (in fact, /dev/block/platform doesn't exist at all). I can't flash the phone; it always freezes at 6% with a communication error. LGUP claims that the current firmware is D85210B, when it was D85220K. I don't know what's going on, and I'm at my wit's end.
Are you using usb 2.0 port and correct dll file.?
Jahanzaibawan said:
Are you using usb 2.0 port and correct dll file.?
Click to expand...
Click to collapse
Well, it worked the first few times I tried it; I actually tested it out by flashing stock MM, and then flashing stock Lollipop again. It all worked 100%.
Update: I specifically made sure to plug it into one of the motherboard's USB 2.0 ports. Still crashes at 6%. The step in particular is LAF INFO.
As for the DLL file, I'm using LGUP_8974.dll, which as far as I know is the correct one for D852 Bell/Virgin.
DarkPhoenixFF4 said:
Well, it worked the first few times I tried it; I actually tested it out by flashing stock MM, and then flashing stock Lollipop again. It all worked 100%.
Update: I specifically made sure to plug it into one of the motherboard's USB 2.0 ports. Still crashes at 6%. The step in particular is LAF INFO.
As for the DLL file, I'm using LGUP_8974.dll, which as far as I know is the correct one for D852 Bell/Virgin.
Click to expand...
Click to collapse
It seems as if your board were changed. or dll is causing the problem.
DarkPhoenixFF4 said:
Yep, just had the same thing happen to me. Can get into TWRP, but can't mount anything, and trying to re-flash the device using Download Mode fails in the same way. Does yours claim it's the old Kitkat install as well?
Update: TWRP is claiming that /system, /data and /cache don't exist at all. The block devices are not listed in /dev (in fact, /dev/block/platform doesn't exist at all). I can't flash the phone; it always freezes at 6% with a communication error. LGUP claims that the current firmware is D85210B, when it was D85220K. I don't know what's going on, and I'm at my wit's end.
Click to expand...
Click to collapse
yes same thing... i had lolipop too, i spent countless hours trying different ways to fix it but twrp won't mount /data so nothing works! I'm about to give up...
Jahanzaibawan said:
It seems as if your board were changed. or dll is causing the problem.
Click to expand...
Click to collapse
What do you mean, my board was changed? As in the physical board? Because I know that's not the case.
DarkPhoenixFF4 said:
What do you mean, my board was changed? As in the physical board? Because I know that's not the case.
Click to expand...
Click to collapse
i'm in the exact same situation, android with blue progress bar, communication fail with device. i'm right now looking for people on xda to help me fix it
my phone is also d852 bell/virgin
what a co-wink-e-dink:laugh:
downlad mode not working
my lg g3 d852 download mode not working plz help me am kdz file flesh but 4% after dq mode big problam downlad mode nt working and phone on all software unforcunatly stoped any help plz software 6.0
Hello to all of you,
Thanks in advance for any help you can provide.
I bought second hand a LG G4 H815 with CyanogenMod 14 already installed on it.
Everything was fine until I installed my Ebanking apps, that would not function with an unlocked bootloader. I needed to return to a clean factory safe state...
It was the second time I flashed a rom in my whole life, the first one was a Galaxy S plus years ago.
I followed all the instructions for the KDZ flash in this tutorial but I stumbled upon a "Upgrade stopped due to error" in LG flash tool.
I retried 3 or 4 times but with no luck. I verified that the ROM was correct for my model and it was. European and all...
I tried LGUP but my phone is unknown ( at least it's detected)...
I read some posts and told myself "I probably have messed up something, let's try it again with a fresh thing"... I clicked on the factory reset button and carried on.
There the phone booted on TWRP (That i didn't know existed before this). As I explored the menus with a TWRP google search on the computer, I began to realize that the factory reset was maybe a bad thing to do with a custom rom. I tried to reboot but I always end up booting on TWRP.
I re-tried to flash in download mode, but with always the "Upgrade stopped due to error".
I also tried to flash directly from TWRP a stock rom. Didn't work.
I was beginning to lose it and tried to flash the CM14 version I had before, juste to have a working phone again, but even this didn't work... I'm stuck with a TWRP phone
I need some help there...
FamousCarpet said:
Hello to all of you,
Thanks in advance for any help you can provide.
I bought second hand a LG G4 H815 with CyanogenMod 14 already installed on it.
Everything was fine until I installed my Ebanking apps, that would not function with an unlocked bootloader. I needed to return to a clean factory safe state...
It was the second time I flashed a rom in my whole life, the first one was a Galaxy S plus years ago.
I followed all the instructions for the KDZ flash in this tutorial but I stumbled upon a "Upgrade stopped due to error" in LG flash tool.
I retried 3 or 4 times but with no luck. I verified that the ROM was correct for my model and it was. European and all...
I tried LGUP but my phone is unknown ( at least it's detected)...
I read some posts and told myself "I probably have messed up something, let's try it again with a fresh thing"... I clicked on the factory reset button and carried on.
There the phone booted on TWRP (That i didn't know existed before this). As I explored the menus with a TWRP google search on the computer, I began to realize that the factory reset was maybe a bad thing to do with a custom rom. I tried to reboot but I always end up booting on TWRP.
I re-tried to flash in download mode, but with always the "Upgrade stopped due to error".
I also tried to flash directly from TWRP a stock rom. Didn't work.
I was beginning to lose it and tried to flash the CM14 version I had before, juste to have a working phone again, but even this didn't work... I'm stuck with a TWRP phone
I need some help there...
Click to expand...
Click to collapse
uninstall any drive for g4 from pc and reinstall again and lgup. now reboot phone to download mode when lgup is open first check upgrade opsion and when open kdz check refurbish opsion and start. good luck
Thank you for your answer
Still no luck
Uninstalled drivers
Rebooted PC
Reinstalled the drivers
Still unknown device
The best way to flash stock image is to use official LG Bridge app. Download it, turn off your phone, connect it to PC while holding volume up button - phone will go into download mode. Then there is option for software restore in LG Bridge but i won't tell u where exactly. If it won't work i would try on another PC. If it won't work maybe you would be able to flash stock image trough send_command but i won't help you with it.
FamousCarpet said:
Thank you for your answer
Still no luck
Uninstalled drivers
Rebooted PC
Reinstalled the drivers
Still unknown device
Click to expand...
Click to collapse
open lgup torn off the phone press volume up insert usb cable wait to see download mode on phone release up button and see if everything go fine
Thank you a lot Avantu, the LG Bridge did the trick! I now have a factory rom!
To preface, I can boot into download mode and access hard reset but cannot boot into the ROM as it just shows the "Broken Android" symbol
I've been trying a lot of steps.... So many guides... To fix my phone. I've chalked it up to an issue with my IMEI/ESF being corrupted as LG Flash Tool shows it as NULL" and fails after 3 seconds consistently. LG UP also fails at 6% spitting out generic errors. I've even tried LGMobile Support Tool and it downloaded the correct firmware but failed to apply it at 2% consistently.
I'm assuming this has to do with my ESF being corrupted. I've been looking up guides on how to "fix" it but keep coming up short as ALL of them require a back up or at least being able to boot into a ROM. However, no ROM will flash. The bootloader is locked and the device has no root options. At this point I'm drawing a blank. I've been going at this for 11 hours straight (no joke, been sitting here for 11 hours searching the forums for different fixes because I know how people feel about the same thing popping up repeatedly.
What caused this issue was trying to roll back the firmware to an earlier version using LGUP so I could unlock the bootloader. I've only been attempting with stock roms (both KDZ and TOT)
Any help would be appreciated.
The phone is still detected in DLMode and all the programs can find it and know it's a D852 but just wont take any firmware.