Related
Moderators, please forgive me in not in the right place...
Came home from a glorious week of camping and decided to check out some 4.4.4 ROM's on my phone...
Already running older version of C-ROM, so backed up and flashed the KK 4.4.4 version. That's where it the wheels came off my bus..
Phone booted so damn slow, then there were hundred's of FC's, rendering the phone unuseable. Rebooted, cleared Dalvik and Cache but same difference. The phone died, the battery would NOT charge! No matter what! Try as I may...NO GO!!! For hours! Feared it was that issue wherein the S3 motherboard dies and the phone has to be replaced by Samsung. Kept trying...finally get the phone to boot into TWRP. Whew!!! Still the phone kept complaining that the battery was dead. WTF?!
Restored the back up I had made...accidentally grabbed another backup from december of last year (Cyanogenmod), so had to recover my C-ROM back instead...RESTORE FAILS! Tried a few times but still failed. Tried to re-flash the latest C-ROM, but STILL fails...everything I'm trying fails.
I read the output and see an error, "Unable to wipe /system" ...found a thread where a user, using TWRP, had the same error with their ROM they were trying to flash. Eventually, the fix was to delete the make_4fs (or whatever it's called) from /sbin directory. Did so and was able to flash my Cyanogen, but could not restore my C-ROM backup. That STILL fails, however, no error in the live output while it's restoring. Just ends up Failing at the end of the restore process. The live logs indicate that it's using the 2fs (or whatever it's called), which was successful in flashing my Cyanogen ROM...why will it not restore my C-ROM back? :crying:
Any help would be greatly appreciated.
kojam said:
Moderators, please forgive me in not in the right place...
Came home from a glorious week of camping and decided to check out some 4.4.4 ROM's on my phone...
Already running older version of C-ROM, so backed up and flashed the KK 4.4.4 version. That's where it the wheels came off my bus..
Phone booted so damn slow, then there were hundred's of FC's, rendering the phone unuseable. Rebooted, cleared Dalvik and Cache but same difference. The phone died, the battery would NOT charge! No matter what! Try as I may...NO GO!!! For hours! Feared it was that issue wherein the S3 motherboard dies and the phone has to be replaced by Samsung. Kept trying...finally get the phone to boot into TWRP. Whew!!! Still the phone kept complaining that the battery was dead. WTF?!
Restored the back up I had made...accidentally grabbed another backup from december of last year (Cyanogenmod), so had to recover my C-ROM back instead...RESTORE FAILS! Tried a few times but still failed. Tried to re-flash the latest C-ROM, but STILL fails...everything I'm trying fails.
I read the output and see an error, "Unable to wipe /system" ...found a thread where a user, using TWRP, had the same error with their ROM they were trying to flash. Eventually, the fix was to delete the make_4fs (or whatever it's called) from /sbin directory. Did so and was able to flash my Cyanogen, but could not restore my C-ROM backup. That STILL fails, however, no error in the live output while it's restoring. Just ends up Failing at the end of the restore process. The live logs indicate that it's using the 2fs (or whatever it's called), which was successful in flashing my Cyanogen ROM...why will it not restore my C-ROM back? :crying:
Any help would be greatly appreciated.
Click to expand...
Click to collapse
Have you tried using ODIN to restore back to stock? If you can get the phone up and running, you may be able to restore from your old backups.
Bass_Man25 said:
Have you tried using ODIN to restore back to stock? If you can get the phone up and running, you may be able to restore from your old backups.
Click to expand...
Click to collapse
Thanks bud.
Oh, I got the phone up and running on the Cyanogen dated dec/2013.
ODIN? Never thought of it. Been such a long time. I do need to get stock on here so I can all the latest official radios etc, then put custom ROMs.
Been such a loooooong time since used ODIN though. Shouldn't be hard to get back on the horse.
Thanks for the suggestion!!!
any idea why this happened? anyone?
as an fyi, I tried to put the lastest SlimROM on but same difference. (i'm really pressed for time always. so I decided this is the quickest thing to try). seems the only thing that will flash is my Cyanogen from December. Strange...
Will have to give ODIN a try if I can ever get the time some day..
Odin shouldn't be a much longer process. Start flash, walk away. When you return 10 minutes to a few hours later, it'll be sitting there waiting for you, all nice and stock!
Anyway, one thing I dont recall seeing you tried is a factory reset. Chances are, that's what caused all your FC. Roms will always take a while on first boot. But all those FC were likely due to incompatible data. Then you may have encountered more data corruption as the system worked overtime trying to resolve all those conflicts.
Its purely a theory, but there's a good chance you will never be able to find exactly what caused all of your issues. Dont lose sleep over it is my best advice! A couple of tips though....
Never wipe/format system! Had you been able to successfully do so, and then nothing would still flash, there would no longer be an o/s to boot into! All roms will format your system partition as the first step in the flash, so there's just no need to do this manually. Most flash failures occur before the flash actually starts, meaning if there's a problem, most times you'll still be able to reboot normally.
Update your firmware. If its been a while since taking an ota or updating via Odin, you're probably on an older firmware build which is known to cause problems with many more recent roms. Most simply will not flash if not updated.
Also, by flashing your up to date firmware in Odin, you will likely fix any corruption which may have occurred on some of those partitions. Good chance you'll be able to flash whatever you want after an Odin firmware update and factory reset.
Hope that helps! Good luck!
DocHoliday77 said:
Odin shouldn't be a much longer process. Start flash, walk away. When you return 10 minutes to a few hours later, it'll be sitting there waiting for you, all nice and stock!
Anyway, one thing I dont recall seeing you tried is a factory reset. Chances are, that's what caused all your FC. Roms will always take a while on first boot. But all those FC were likely due to incompatible data. Then you may have encountered more data corruption as the system worked overtime trying to resolve all those conflicts.
Its purely a theory, but there's a good chance you will never be able to find exactly what caused all of your issues. Dont lose sleep over it is my best advice! A couple of tips though....
Never wipe/format system! Had you been able to successfully do so, and then nothing would still flash, there would no longer be an o/s to boot into! All roms will format your system partition as the first step in the flash, so there's just no need to do this manually. Most flash failures occur before the flash actually starts, meaning if there's a problem, most times you'll still be able to reboot normally.
Update your firmware. If its been a while since taking an ota or updating via Odin, you're probably on an older firmware build which is known to cause problems with many more recent roms. Most simply will not flash if not updated.
Also, by flashing your up to date firmware in Odin, you will likely fix any corruption which may have occurred on some of those partitions. Good chance you'll be able to flash whatever you want after an Odin firmware update and factory reset.
Hope that helps! Good luck!
Click to expand...
Click to collapse
What's up, Doc? Sorry for that...
I downloaded Odin this morning. I should have gotten the link from XDA. The site i got it from looked official, however, tons of endless pop-ups after I installed it. Freak!!!
Then found the xda links. Not sure which version to get because i didn't see which one handles the S3. The latest version (3.09) should, no?
As well, where do i get the stock ROM from? Forgive me for all these questions. Been extremely busy with work these past few months. No time to play around with my phone everything. I'm forgetting more than I know.
A full wipe was done. In TWRP, system was check (it's always checked) automatically when wiping to flash a new ROM.
Thanks again!
Everything you need is in my sig. Go to the firmware thread and the stock or root66 firmware listed there us what you flash in odin. Version 3.09 is fine btw.
DocHoliday77 said:
Everything you need is in my sig. Go to the firmware thread and the stock or root66 firmware listed there us what you flash in odin. Version 3.09 is fine btw.
Click to expand...
Click to collapse
Thanks!
S.O.S!!!
kojam said:
Thanks!
Click to expand...
Click to collapse
Downloaded the rooted firmware from your link and the ODIN (3.09)...
Flashed the firmware (making sure to get the correct one for WIND)...ODIN did it's thing...got a green pass...the phone rebooted...got the Samsung symbol, little swoosh animation, and the accompanying sound effect that goes with the swoosh-thing...THE PHONE NEVER BOOTED UP AN O/S!
Did it at about 11:30 last night, left it, got up this morn, and phone STILL in same status!
Found out that site where I downloaded the firmware had an issue last night. They posted this morn, apologizing to people about a D.O.D attack that may have caused dropped downloads. I downloaded the firmware again this morn, flashed with ODIN, got a pass....SAME THING!!! Phone
Had to quickly pack up my laptop to bring with me to the office. Will try the official, non-rooted firmware to see if I can get it to go.
Problems' that my team went from 12 to 2 people...my partner's off today...and I got a LOUD MOUTH across from me who WILL NOT leave me alone, no matter what I say or do. LOL.
Any suggestions?
In the words of George Costanza:
"I'm BACK, babyyyyyyy!!!!!"
The official firmware worked!
Phone's back online. Thanks for all your help. Will have to see about rooting later...as well, want to see how the battery operates on stock firmware. I've tried EVERYTHING under the sun to preserve batt life and NOTHING worked!!!
Tried EVERY KERNEL noted to be good on battery life, tried TONS of apps that were supposed to help, turned off as much as I could, etc....
batt still not good. I give up. Every diagnostic app says batt is very good. I dunno...
Earplugs! Lol! I definitely feel for you about your work status! Been there!
About the firmware though, if the download had been corrupted, it would've failed the initial check done by Odin. You are probably ok. Dont worry just yet!
If it is hanging up at the Samsung screen, you probably just need to factory reset. Almost always fixes this. (It happens due to incompatible data left from your previous rom)
This will wipe internal sdcard though, so if you haven't backed up yet, the next thing to fo is flash TWRP via Odin. You can then use its built in file manager to copy whst you need first. Or you can then flash an insecure kernel and use adb if you're familiar with that.
The Doc is in!
if the download had been corrupted, it would've failed the initial check done by Odin
Click to expand...
Click to collapse
That's EXACTLY my thought too. That was really perplexing...
I am up again...
Facotry Reset? How do I do that if stuck at the Samsung splash though?
Now that i know the official firmware works, maybe i'll, try again with the rooted firmware, try to factory reset when stuck, and continue to flash TWRP as you described above. Don't mind factory resetting. I've taken everything I need.
Oh!!!!
I noticed that all the apps I had before flashing the firmware are STILL on my phone. I would have thought that they would have been wiped out completely when lord ODIN was doing her thing.
....and battery life is STILL pretty bad...
Phone's been charging...became fully charged...unplugged it..it was down to 84% after only about 30/mins.
Will see how it goes after doing the factory wipe.
Again, how do i do a factory wipe if stuck at the Samsung swoosh after I re-flash the rooted firmware ?
Maybe your battery is dying. it happens. That would explain a big drop from the start.
To factory reset if you're stuck at boot up, turn the phone off, then boot up into recovery. Hold volume up, home and power. After it vibrates, release power only, continue holding the other two until you see recovery booting up.
If stock recovery is installed, choose factory reset.
In TWRP (probably similar in cwm) go to Wipe and choose factory reset there. In TWRP and CWM, factory resetting does not wipe your internal sdcard. Stock recovery will.
And as for Odin, it doesn't actually touch the user data partition, so all your apps and data are preserved. This is great when just upgrading from one build to the next, but is the reason a factory reset is required if coming from a non touchwiz rom.
---------- Post added at 03:59 PM ---------- Previous post was at 03:53 PM ----------
How old is your battery? The S3 is at the age where people who bought it when it was first released will start to notice the battery is beginning to degrade.
You can also get an app called Better Battery Stats here on xda (paid version in the play store). Its the goto utility for investigating problems with battery drain. Run it for a day after a full charge and then check its logs for persistent wakelocks. The app thread should explain its use better than I can, but if you are having trouble you can always post your bbs log here for one of us to look over. (This isnt my strongest area, but there are a few others around that may also be able to help. )
TL;DR Trying to get my phone to stock to accept OTA, running this rom http://forum.xda-developers.com/showthread.php?t=2485319 and unlocked bootloader/s-off with stock recovery flashed via Flashify. Anything else I should do?
So, let me preface this by saying that I am very, very new to this. I have a rooted tablet that I use, and that was a simple process. No adb commands or anything. But, when I rooted my phone using sunshine, I had no clue the world of **** I was about to get into. I rooted the phone, got a custom recovery on it, and all was going well. Until I accidentally wiped system, and was left without an OS. So, after the quick process of learning how to sideload, I got ViperOne installed on the phone and had it working. Yay for XDA help!
Not over yet though. Soon, over time, I was unable to accept calls. The phone would ring, and I would be able to answer, but no audio output and the mic wasn't picking anything up either. So, I found some fixes regarding google now voice detection, and all went well for about half an hour. Then it stopped working again. Frustrated, I bought another phone (galaxy s4), and decided I'd just get my HTC back to stock as possible.
Now for the question. I'm running this rom http://forum.xda-developers.com/showthread.php?t=2485319 , and I have the stock recovery (I flashed the recovery using Flashify, then rebooted the phone). All seems to be running well, despite the recovery flash wiping everything from the phone. My question is, seeing as I'm on that ROM, the latest firmware/radio/hboot, and stock recovery, and unlocked/s-off, could I accept and safely install the OTA when it rolls out? Thanks for any help, and sorry for writing so much!
Hey, check your Reddit post I gave you some info there.
Hello All,
Due to my endless frustrations, this might be a long one so please bear with me!
So I purchased a Verizon Global HTC ONE M7 from the States, I am currently in Nigeria and the only thing that makes me sadder and more frustrated than the state of my phone right now is the incessant terror attacks in the country! Initially, almost everything worked fine when i popped in my new Etisalat sim card into the phone, except for the mobile hotspot (which just conveniently turns out to be the one of the top 3 most important features in a phone for me - probably the feature I use the most) this message kept popping up about how hotspot couldn't be used without a VZW sim, etc (also with the non-verizon sim warning when the phone boots up). I tried all I could, eventually deciding to flash a new ROM to clear out everything Verizon and start fresh.
Enter Viperone 6.2.0 - everything worked initially, but after a few weeks i noticed if I did anything like watch a youtube video or download something over a few MBs 90% of the time the data drops (no visible signs like changes from E to H or 3g or the likes, everything looks the same, just that the data stops), toggle mobile data on/off and data connection is back. It worsened and became more frequent over time. Upgraded to Viperone 6.2.1, no difference, so i figured its probably the viperone rom.
Enter Cyanogenmod - http://forum.xda-developers.com/ver...-oneplus-one-stock-rom-cm11s-verizon-t2857425 - and its the same exact issue from the beginning, so im guessing its not to do with the ROM at all (though there are one or two niggling issues with the ROM - cant change BBM display pic, etc)?! I've really tried to comb through the forum and see what makes sense that i could try without bugging y'all - I did a factory reset, wiped everything completely and its the same thing.
I've seen suggestions to similar issues like: flash stock recovery, update radio/firmware/kernel, flash back to custom recovery and some other things which are beginning to sound quite dangerous in my ignorance!! I did believe updating the firmware made sense but after digging deeper, i must honestly say i'm quite confused on what to do. what radio/firmware/kernel works with what software version, etc- most firmware that i've seen are 4.4.3 compatible, while this ROM is 4.4.4., some of them seem to be for stock ROMs only and a lot of other confusions.
So, I'm not gonna be a hero and brick my phone from trying to do what i do not understand, instead here i am, hat in hand, crying out for help after suffering for 3 months! Its really frustrating as, downloads break causing me to lose data, skype or MSLync calls always break and im beginning to look unprofessional to people! This is why I have decided to put up a post of my own specific to my case so i don't medicate for someone else's ailments. So please........ WHAT EXACTLY DO I DO??
PHONE DETAILS (typing it out as i've just realized on this ROM i can't take screenshots with Power+Home button combo anymore and can't be bothered at this point!!!)
ANDROID VERSION: 4.4.4
BASEBAND VERSION: 1.12.41.1112_2
KERNEL VERSION: 3.4.82-gfe09065; [email protected] #1; Wed oct 8 01:36:03 PDT 2014
BUILD DATE: SUN AUG 3 23:00:51 PDT 2014
BUILD NUMBER: CYANOGENMOD 11S v5 (Verizon)
SELinux status: Enforcing
Thanks
Have you tried a stock version of sense? Essentially what our phone was meant to run. Viper uses a lot of custom tweaks for the masses, and sometimes carrier specifics get finicky. I would suggest santods stock Rom, bonestock, or ecliptic. I think nusense uses an international base and not strictly vzw, but you could also try that one...and santod can clarify about the details.
Hope you get it going.
Sent from my One.
Can you flash stock recovery from Santod's firmware thread and do a factory reset? It could be a corrupt nv partition which would only be fixed by doing a factory reset via stock recovery. (If you must, make a nandroid of system and data in your recovery of choice so you can restore your data if you wish).
Uzephi said:
Can you flash stock recovery from Santod's firmware thread and do a factory reset? It could be a corrupt nv partition which would only be fixed by doing a factory reset via stock recovery. (If you must, make a nandroid of system and data in your recovery of choice so you can restore your data if you wish).
Click to expand...
Click to collapse
Thanks for the responses folks, i'll try out your suggestions and revert..
8100
brymaster5000 said:
Have you tried a stock version of sense? Essentially what our phone was meant to run. Viper uses a lot of custom tweaks for the masses, and sometimes carrier specifics get finicky. I would suggest santods stock Rom, bonestock, or ecliptic. I think nusense uses an international base and not strictly vzw, but you could also try that one...and santod can clarify about the details.
Hope you get it going.
Sent from my One.
Click to expand...
Click to collapse
So.. i found time to get to this and decided to go with your suggestion of Santod's stock rom... and now, i think i've done the unthinkable!! After WIPING EVERYTHING "All partitions except SD!" as the instructions stated... i attempted to reboot into bootloader and got a message saying "no OS installed, are you sure you want to reboot"... that scared me a bit, but i thought surely, it must be part of the process! I proceed to reboot to bootloader to flash the firmware and i cant seem to do anything!!
Fastboot is stuck on " waiting for device" for everything i try.
Also, i rebooted back into recovery and attempted to install the stock rom: i get the error message "unable to open zip file"..
Have i destroyed my phone with my own hands, people? :crying:
Mr HaRR said:
So.. i found time to get to this and decided to go with your suggestion of Santod's stock rom... and now, i think i've done the unthinkable!! After WIPING EVERYTHING "All partitions except SD!" as the instructions stated... i attempted to reboot into bootloader and got a message saying "no OS installed, are you sure you want to reboot"... that scared me a bit, but i thought surely, it must be part of the process! I proceed to reboot to bootloader to flash the firmware and i cant seem to do anything!!
Fastboot is stuck on " waiting for device" for everything i try.
Also, i rebooted back into recovery and attempted to install the stock rom: i get the error message "unable to open zip file"..
Have i destroyed my phone with my own hands, people? :crying:
Click to expand...
Click to collapse
FALSE ALARM FOLKS!!! I decided to attempt flashing the CM11 rom i just uninstalled and it worked. Turns out its a known issue with the .zip file for that rom - i am now re-downloading from another mirror. Meanwhile the Fastboot thing was just a driver issue - though i'm surprised because i had all the drivers installed on the system and have used fastboot successfully - anyway i reinstalled the drivers and all was well with fastboot again.
NB: Don't get tired of me just yet please!
brymaster5000 said:
Have you tried a stock version of sense? Essentially what our phone was meant to run. Viper uses a lot of custom tweaks for the masses, and sometimes carrier specifics get finicky. I would suggest santods stock Rom, bonestock, or ecliptic. I think nusense uses an international base and not strictly vzw, but you could also try that one...and santod can clarify about the details.
Hope you get it going.
Sent from my One.
Click to expand...
Click to collapse
hello!
Thanks for your ideas guys. I'm currently running Santod's stock rom (which is brilliant, i must say, i actually wanna stay on this rom) since friday - thought i'd give it the whole weekend and see how it goes.. BUT! i still get thoseconnection drops.. and frequently too.
Any other ideas on what the issue could be?
Mr HaRR said:
hello!
Thanks for your ideas guys. I'm currently running Santod's stock rom (which is brilliant, i must say, i actually wanna stay on this rom) since friday - thought i'd give it the whole weekend and see how it goes.. BUT! i still get thoseconnection drops.. and frequently too.
Any other ideas on what the issue could be?
Click to expand...
Click to collapse
If doing factory reset from stock recovery doesn't fix it, it is most likely a burned SIM. It has happened to me. (Average 150+ GB a month in data, so I burn em easily)
Sent from my HTC6500LVWBLU using XDA Free mobile app
Uz has it right, you need to flash a stock recovery and THEN do a factory reset, then reload your custom recovery and rom. I had the exact same issue before. Or you could flash an ruu file which would reset the partitions also.
ccarr313 said:
Uz has it right, you need to flash a stock recovery and THEN do a factory reset, then reload your custom recovery and rom. I had the exact same issue before. Or you could flash an ruu file which would reset the partitions also.
Click to expand...
Click to collapse
Hey folks, apologies for the touch and go nature of this thread - i just don't have a lot of free time on my hands and other reasons..
Anyhow, i think I want to try out ur suggestion of flashing an RUU - I noticed that im unable to actually enter recovery after flashing stock recovery from Santod's thread (i flashed the latest three recoveries). I can get to bootloader, but when i select recovery, the phone goes black for a few seconds and then i get the RED TRIANGLE WITH THE EXCLAMATION MARK INSIDE, obviously something's wrong, few seconds later the phone reboots itself into normal mode. I did do a factory reset from bootloader, but issue persists.
So now to the RUU flashing issue - could you suggest one for me to flash?
By the way though, isn't flashing an ruu gonna take me back to stock completely (as in back to S-ON, ETC..)?
Thanks a whole bunch - IM DETERMINED TO GET THIS TO WORK!!!
Mr HaRR said:
Hey folks, apologies for the touch and go nature of this thread - i just don't have a lot of free time on my hands and other reasons..
Anyhow, i think I want to try out ur suggestion of flashing an RUU - I noticed that im unable to actually enter recovery after flashing stock recovery from Santod's thread (i flashed the latest three recoveries). I can get to bootloader, but when i select recovery, the phone goes black for a few seconds and then i get the RED TRIANGLE WITH THE EXCLAMATION MARK INSIDE, obviously something's wrong, few seconds later the phone reboots itself into normal mode. I did do a factory reset from bootloader, but issue persists.
So now to the RUU flashing issue - could you suggest one for me to flash?
By the way though, isn't flashing an ruu gonna take me back to stock completely (as in back to S-ON, ETC..)?
Thanks a whole bunch - IM DETERMINED TO GET THIS TO WORK!!!
Click to expand...
Click to collapse
That is in fact stock recovery man. When you get the triangle press volume up and power at the same time. You will enter stock recovery.
Any of my ruu will run fine. You won't lose s-off or unlocked status. You flash them in boot loader fastboot mode.
dottat said:
That is in fact stock recovery man. When you get the triangle press volume up and power at the same time. You will enter stock recovery.
Any of my ruu will run fine. You won't lose s-off or unlocked status. You flash them in boot loader fastboot mode.
Click to expand...
Click to collapse
HA! and now i feel :silly: !!
Bless your soul! i'll give it a go shortly...
So...
Last week, my wife's Tab S went into a bootloop. She runs complete stock, we haven't rooted, or anything. There had been a notification about an update, but she hadn't touched it. She'd updated to Lollipop at some point last year, but hadn't applied the absolute latest update. One day last week, she just turned it on, and it started bootlooping.
Because it was so stock, there were no backups, no nandroids, or anything like that. No Custom Recovery. I told her "well, we can just do a factory reset. You'll lose everything, but once we get you back up and running, it'll just re-download everything from the Goog." So we factory reset it. Looked good for a minute, booted into the first screen, enter in your Wi-Fi password, all that. As soon as we got the Wi-Fi password entered, however, it re-booted. And keep rebooting. Bootloop city. No problem. I walked her through (over the phone) using Odin to flash the latest Lollipop firmware. No dice. It appeared to flash successfully, but still bootlooped.
Over the weekend, I tried using Kies to flash the most official firmware I could find. Everything was successful -computer recognized the device, was able to download "direct from the source," as it were, but it got stuck at 69% twice before failing. I read somewhere that one had to run Kies in administrator mode to get it to successfully complete. So I did, and it got past 69%, successfully completing the flash. STILL NO LUCK. STILL WITH THE BOOTLOOPS.
Last night, I realized that I hadn't flashed in Odin using Administrator Mode. Tried it, using latest 5.0.2 (XAR-Cellular South). Flashed successfully, all appeared well. Still bootlooped.
So, I'm stuck. I can get into recovery, I can get into Download Mode, I can successfully flash. I just can't get the darn thing booted.
Thoughts, anyone? Should I try flashing a Custom ROM? How hard is that using Odin? Thanks in advance.
Ok this will take a few tries but here is my method of dealing with this situation
1) Flash stock using Odin
2) AS SOON AS the screen goes blank, start holding Power+Volume Up+Home
3) When recovery boots, release the buttons
4) Use the volume buttons to select "Wipe data/factory reset"
5) Press power to confirm
6) Reboot
If that doesn't work, you may either:
1) (more likely) Installing a ROM will fix the problem
2) (unlikely but possible) You might have worn NAND pages, which I doubt but could cause this behavior.
Nandr0idC0nsumer said:
Ok this will take a few tries but here is my method of dealing with this situation
1) Flash stock using Odin
2) AS SOON AS the screen goes blank, start holding Power+Volume Up+Home
3) When recovery boots, release the buttons
4) Use the volume buttons to select "Wipe data/factory reset"
5) Press power to confirm
6) Reboot
If that doesn't work, you may either:
1) (more likely) Installing a ROM will fix the problem
2) (unlikely but possible) You might have worn NAND pages, which I doubt but could cause this behavior.
Click to expand...
Click to collapse
Thanks, I'll try these steps tonight when I get home, and report back!
All right, here's something interesting. Before I tried your first step, I remembered that the other night, I left it stuck at the Samsung logo -it was just kind of stuck there, and since the behavior was a little different than I'd seen before (not continuous bootlooping), I thought I'd boot into recovery and wipe. I did, I wiped (factory reset), and rebooted. The tablet booted into the first screen, Accessibility/Wi-Fi, blahblah. This was where it usually rebooted. On a hunch, I bypassed entering in my WiFi key. I then bypassed almost everything else (Samsung account, Google account, etc.), expecting that the tablet would reboot at any moment. But I made it to the front apps page, where it shows you the side-launcher, the Magazine-Flipboard thingie, and whatnot. Wi-Fi still not connected, though. I opened up the app drawer, and scrolled around. Looked really good for a moment. I even took a picture with the camera, and viewed it in Gallery! Feeling brave, I thought, "well, maybe it just needed a couple of minutes before firing up the radio." So I went into settings, and inputted my WiFi key. It connected. And rebooted into its bootloop. (getting so tired of that boot-sound).
Went ahead and flashed the most original stock firmware I could find. As always, flashed successfully. As soon as it booted, I made my way to recovery, and wiped, per your instructions. No luck. Bootloop again.
It's something in the WiFi is what I've come to think as a result of the above. Which I don't entirely understand, as I thought the radio got re-flashed with the firmware.
I'm ready to try flashing a Custom Rom. Can I do that through Odin, or should I try and flash TWRP, and do it through there? Will TWRP flash without a working (bootable) OS?
All right. Thanks for your response!
Try this as a test.
First make a full backup of every partition with twrp including the EFS <<IMPORTANT!
Get it booting again without wifi then root the device and delete the EFS folder or delete it in recovery.
Reboot the device and try and enable wifi.
ashyx said:
Try this as a test.
First make a full backup of every partition with twrp including the EFS <<IMPORTANT!
Get it booting again without wifi then root the device and delete the EFS folder or delete it in recovery.
Reboot the device and try and enable wifi.
Click to expand...
Click to collapse
Got TWRP installed. Won't backup. Fails at 16% (system partition, I think). Just powers down to battery indicator in the middle of the backup. Looks like it backs up the EFS, though, since it's the first one. And when I go into TWRP's Restore option, there's a backup there (though I don't dare try and restore it).
Now I have to figure out a way to get the Custom ROM and GAPPS I downloaded onto the tablet without a reliable boot... It's gotten to the front screen a time or two tonight, but starts looping even when I bypass the WiFi setup.
Entered adb/TWRP interface. Tried to push two files, a Custom ROM file, and a GAPPS file. The ROM failed, with some sort of "Error 7," incompatible data, blahblah... Just out of curiosity, I tried to push the GAPPS file, and that failed after about 6%, and the tablet powered off.
I'm running out of ideas.
copied a custom rom to a USB/OTG stick (thumbdrive), and plugged it in. Fired up TWRP, tried to install. Wouldn't. Wouldn't install GAPPS, either. Looks like the only way it wants to flash anything is through ODIN or KIES.
The Latest...
All right...
I remembered that sometimes the TWRP version mattered. When I installed TRWP last night, I installed the latest and greatest, 3.0.2. Last night after I gave up, I remembered that sometimes, the latest and greatest TWRP doesn't install things perfectly. So, this morning, I downloaded TWRP 2.8.6-ish onto the USB/OTG device, and re-flashed the recovery partition. To be honest, I was surprised that TWRP was even able to flash that (but the TWRP image is only like 9.8 MB, so...)...
Got TWRP 2.8.6.0 flashed, and rebooted into TWRP. Immediately decided to try and re-flash the custom ROM that I'd tried unsuccessfully to flash last night, since the thumbdrive was still plugged in. Resurrection Remix Lollipop. Lined up GAPPS in the queue, as well. The ROM *appeared* to flash better than it had in TWRP 3.0.2, but it was sort of hard to see... GAPPS failed, and I was prepared to watch another round of bootloops. It did bootloop, sort of. The RR splash screen appeared, said that it was installing (or preparing) xx out of XX apps. Then, it rebooted. I figured it was doing its bootloop thing. However, it got to the same screen, "installing xx out of XX apps. Except that XX number had gone down, and the xx number had gone up. It repeated this action about 4 times --the last time I saw it reboot, it was "installing 1 out of 2 apps." And then...?
It booted into the RR lockscreen.
Of course, there were no GAPPS. In fact, there are something like only 20 apps total on the tablet. But it appears somewhat stable at the moment. (See picture).
Afraid to try and connect WiFi, afraid that it'll just bootloop.
Speaking of bootloop. At one point, once we got it booted, my wife hit an option in the Settings. LCD Density, I believe. As soon as she hit it (she literally just placed her finger over the 320 default option), the tablet rebooted. No loop, though. Rebooted straight back to the RR lockscreen.
So I appear to have a somewhat stable OS flashed onto the tablet at the moment. No GAPPS, though. No WiFi.
Anybody have a suggestion on where to go from here? I have my doubts as to whether or not I can even back up this configuration.
Sorry about all the updates. I kind of figured that if *anyone* else ever goes through what I'm going through, they'll have some sense of all the different things that can be tried in resurrecting a bricked/bootlooping device. I appreciate everyone's efforts to date -thank you so much, @Lightn1ng and @ashyx.
All right, because I can't leave well enough alone....
I got WiFi up and working. Tablet still stable and working. Wheeeee.... No GAPPS, though.
Downloaded GAPPS, second-smallest package from opengapps- only 128M (5.1 ARM package). Downloaded it in Android, from the tablet! Tried to flash it in TWRP. Failed, tablet rebooted halfway (not even) through. Now it's bootlooping again...
I should've left well enough alone, and waited for someone. Have tried re-installing Resurrection Remix, but tablet keeps failing to flash. Might have to try and flash a different TWRP. I don't know...
Have you tried another Gapps? Also, is this the WiFi only model or the LTE model we're talking about?
Lightn1ng said:
Have you tried another Gapps? Also, is this the WiFi only model or the LTE model we're talking about?
Click to expand...
Click to collapse
It's the WiFi-only model - SM-T800.
It's kind of weird. I thought it might be some sort of internal memory problem (like the worn Nand pages you mentioned), since almost anything I try to do in TWRP fails (although I was able to flash an entire Custom ROM the one time AND get it booted) -but backing up isn't working, whether it's to internal/external SD. And the fact that I can flash perfectly (subjective term there) well using Odin or Kies tells me that whatever problems the tablet is having, something's getting through.
I'll try a different GAPPS package. Right now, though, TWRP isn't letting me flash hardly anything, and moving files back and forth on this thing is just awful.
AGH - I was so close!
daina said:
It's the WiFi-only model - SM-T800.
It's kind of weird. I thought it might be some sort of internal memory problem (like the worn Nand pages you mentioned), since almost anything I try to do in TWRP fails (although I was able to flash an entire Custom ROM the one time AND get it booted) -but backing up isn't working, whether it's to internal/external SD. And the fact that I can flash perfectly (subjective term there) well using Odin or Kies tells me that whatever problems the tablet is having, something's getting through.
I'll try a different GAPPS package. Right now, though, TWRP isn't letting me flash hardly anything, and moving files back and forth on this thing is just awful.
AGH - I was so close!
Click to expand...
Click to collapse
I'm running out of ideas!
Maybe somebody else with a T800 could backup their entire EMMC using
Code:
dd if=/dev/mmcblk0 of=/sdcard/full_nand_dump.bin
And you take the file on your tablet and do
Code:
dd if=/sdcard/full_nand_dump.bin of=/dev/mmcblk0
And restore YOUR efs folder using TWRP.
THIS IS A DANGEROUS OPERATION AND I AM NOT RESPONSIBLE FOR ANYTHING THAT GOES WRONG!
---------- Post added at 08:01 PM ---------- Previous post was at 07:57 PM ----------
@ashyx Any more ideas before I go ahead with my evil world domination plan to recover this device?
I wouldnt carry out any risky operations until a full backup can be made with twrp or you may end up with an unrecoverable device.
If twrp cannot backup the system partition then there is an issue with the partition.
Try backup again and post the recovery log, it may contain some relative information.
I have the same issues and have tried eveything. I was rooted and running the latest Pheonix rom on my sm-t800. Last Wednesday (8-10) I starting getting boot loops out of nowhere, no new apps nothing just a daily driver. I've been through everything on here and have gone back to bone stock but to no avail, the boot loops just keep coming. I can connect to wifi and get things set up but if I try to use anything more than 'light usage' the tab starts its boot loops again and rows fits for about 10 minutes and always different timing on the boot. Sometimes it will make it to the Samsung logo, sometime only to Tab S and sometimes about 10 seconds of usage.. I know this isn't helping much but wanted to let you know there are more of us with the same problem. Will be blab to try anything to help said issue.
Exactly the same issue on my LTE version.
Samsung support just asked me 230€ for a new motherboard.
I refused to repair. I think it is related to nand memory..
Hello I have both the 8.4" and 10.5" I updated the 8.4" to Android 5.02 nothing but boot loops my other is still on 442 and I wont be updating it as its working fine. I have been reading a few posts and the problem was right in front of me all the time I have 2 internet connections 2.4 GHZ and 5.0 GHZ if I connect to the 5.0 GHZ I get boot loops but if I stay on 2.4 GHZ no problems what so ever so I may just install a custom rom and my 10.5 tab and stay clear of the faster internet.
srfairhurst said:
Hello I have both the 8.4" and 10.5" I updated the 8.4" to Android 5.02 nothing but boot loops my other is still on 442 and I wont be updating it as its working fine. I have been reading a few posts and the problem was right in front of me all the time I have 2 internet connections 2.4 GHZ and 5.0 GHZ if I connect to the 5.0 GHZ I get boot loops but if I stay on 2.4 GHZ no problems what so ever so I may just install a custom rom and my 10.5 tab and stay clear of the faster internet.
Click to expand...
Click to collapse
Why not just update to Marshmallow? Absolutely no issues for me.
ashyx said:
Why not just update to Marshmallow? Absolutely no issues for me.
Click to expand...
Click to collapse
Now i figured out its the wifi thats causing the problem i will update to android 6.01 or if i can find a good custom rom il risk that.
daina said:
It's the WiFi-only model - SM-T800.
It's kind of weird. I thought it might be some sort of internal memory problem (like the worn Nand pages you mentioned), since almost anything I try to do in TWRP fails (although I was able to flash an entire Custom ROM the one time AND get it booted) -but backing up isn't working, whether it's to internal/external SD. And the fact that I can flash perfectly (subjective term there) well using Odin or Kies tells me that whatever problems the tablet is having, something's getting through.
I'll try a different GAPPS package. Right now, though, TWRP isn't letting me flash hardly anything, and moving files back and forth on this thing is just awful.
AGH - I was so close!
Click to expand...
Click to collapse
DrinkSlinger said:
I have the same issues and have tried eveything. I was rooted and running the latest Pheonix rom on my sm-t800. Last Wednesday (8-10) I starting getting boot loops out of nowhere, no new apps nothing just a daily driver. I've been through everything on here and have gone back to bone stock but to no avail, the boot loops just keep coming. I can connect to wifi and get things set up but if I try to use anything more than 'light usage' the tab starts its boot loops again and rows fits for about 10 minutes and always different timing on the boot. Sometimes it will make it to the Samsung logo, sometime only to Tab S and sometimes about 10 seconds of usage.. I know this isn't helping much but wanted to let you know there are more of us with the same problem. Will be blab to try anything to help said issue.
Click to expand...
Click to collapse
Hello,
and the rest of story??
i can flash TWRP in download mode, and i can intall zip by TWRP , the lineage rom,
but, cant odin flash official md5 file, it stucks on logo.
I fixed (to a certain degree) a bootlooped watch by installing a stock Lollipop Rom. It does not work though, because watch cannot connect with Android wear and therefore not complete installation. (It does pair up with the phone and says wait a minute) Any suggestions?
baronimus said:
I fixed (to a certain degree) a bootlooped watch by installing a stock Lollipop Rom. It does not work though, because watch cannot connect with Android wear and therefore not complete installation. (It does pair up with the phone and says wait a minute) Any suggestions?
Click to expand...
Click to collapse
Our watches must be brothers as I have had the exact same scenario. I did however get it back going to LP, paired, etc to the smartphone. What I had to do was fastboot format cache, then userdata, then fastboot reboot. I then fastboot flash the .simg file, the recovery.img file and the boot.img file, then fastboot reboot. I then connected to XC which did not work all the way through, but gave me access to be able to use twrp.img (for some reason, twrp would not boot in LP). Then in twrp I adb pushed the LP rom that is signed and after pushed, installed it. Then, I had to leave it alone for the battery drain as it was locked up or something. After it drained, which was evident because it was not warm, I charged it and it is now working again...but only in LP. I cannot get MM installed.
IF you happen to get MM installed and working, please advise your steps.
golfnut22 said:
Our watches must be brothers as I have had the exact same scenario. I did however get it back going to LP, paired, etc to the smartphone. What I had to do was fastboot format cache, then userdata, then fastboot reboot. I then fastboot flash the .simg file, the recovery.img file and the boot.img file, then fastboot reboot. I then connected to XC which did not work all the way through, but gave me access to be able to use twrp.img (for some reason, twrp would not boot in LP). Then in twrp I adb pushed the LP rom that is signed and after pushed, installed it. Then, I had to leave it alone for the battery drain as it was locked up or something. After it drained, which was evident because it was not warm, I charged it and it is now working again...but only in LP. I cannot get MM installed.
IF you happen to get MM installed and working, please advise your steps.
Click to expand...
Click to collapse
Thank you for your reply. I will certainly let you know of any progress. The procedure I followed was somewhat more simple. I flashed the twrp with fastboot, booted twrp up, transferred the downloaded rom image from the pc to the watch and booted the rom from twrp. It then starts up but fails to play with wear.
baronimus said:
Thank you for your reply. I will certainly let you know of any progress. The procedure I followed was somewhat more simple. I flashed the twrp with fastboot, booted twrp up, transferred the downloaded rom image from the pc to the watch and booted the rom from twrp. It then starts up but fails to play with wear.
Click to expand...
Click to collapse
Regarding the pairing with phone, I had to go in the phone settings, application manager, open android wear, and clear the data and cache in order for it to recognize my watch. I had previously had it linked to another phone and had the phone connected to a different watch so I think it was getting confused.
Regarding getting past the 5.0.1 update, I have found this post http://forum.xda-developers.com/smartwatch-3/orig-development/tut-how-to-fix-swr50-fastboot-t3258918 and am currently getting OTA updates as I write. I don't know how far I will get, but so far I have had two updates. I did not flash the updates, only the original rom. Then I went into the watch settings, about, and pressed the software or system update (I've been doing it manually each time).
Edit: It allowed me to update all the way to MM, however I got the 4 dots /symbols again when it was rebooted. Up to that point, which the last update was the LCA43, the watch appeared to be working fine. I did not test it much as I was just trying to get all the updates I could. So, while it did not go all the way thru to MM, I still was very happy that I got up to that update.
golfnut22 said:
Regarding the pairing with phone, I had to go in the phone settings, application manager, open android wear, and clear the data and cache in order for it to recognize my watch. I had previously had it linked to another phone and had the phone connected to a different watch so I think it was getting confused.
Regarding getting past the 5.0.1 update, I have found this post http://forum.xda-developers.com/smartwatch-3/orig-development/tut-how-to-fix-swr50-fastboot-t3258918 and am currently getting OTA updates as I write. I don't know how far I will get, but so far I have had two updates. I did not flash the updates, only the original rom. Then I went into the watch settings, about, and pressed the software or system update (I've been doing it manually each time).
Edit: It allowed me to update all the way to MM, however I got the 4 dots /symbols again when it was rebooted. Up to that point, which the last update was the LCA43, the watch appeared to be working fine. I did not test it much as I was just trying to get all the updates I could. So, while it did not go all the way thru to MM, I still was very happy that I got up to that update.
Click to expand...
Click to collapse
I now succeeded in pairing up with the phone. What I did was to flash another Rom which I found in the forum. It's called ROM_SW3_5.1.1.2_LCA43. Now the watch works just fine on Lollipop and updates automaticly. I am going to try and upgrade to MM but I fear its going to get stuck on the infamous four symbols when I do. I am happy though to have the watch up and running again, it was deemed paperweight for a while
Ok stuck again. Still at Lollipop version 5.1.1.2
baronimus said:
I now succeeded in pairing up with the phone. What I did was to flash another Rom which I found in the forum. It's called ROM_SW3_5.1.1.2_LCA43. Now the watch works just fine on Lollipop and updates automaticly. I am going to try and upgrade to MM but I fear its going to get stuck on the infamous four symbols when I do. I am happy though to have the watch up and running again, it was deemed paperweight for a while
Ok stuck again. Still at Lollipop version 5.1.1.2
Click to expand...
Click to collapse
Does yours actually have 5.1.1.2 in the about section? Mine says 5.1.1 with the build as LCA43.
golfnut22 said:
Does yours actually have 5.1.1.2 in the about section? Mine says 5.1.1 with the build as LCA43.
Click to expand...
Click to collapse
Indeed it does. The Rom comes from here: http://forum.xda-developers.com/smartwatch-3/orig-development/rom-sony-smartwatch-3-rom-t3367728
Since the problem occurs only when updating to MM I am led to think that we have a kernel issue?
baronimus said:
Indeed it does. The Rom comes from here: http://forum.xda-developers.com/smartwatch-3/orig-development/rom-sony-smartwatch-3-rom-t3367728
Since the problem occurs only when updating to MM I am led to think that we have a kernel issue?
Click to expand...
Click to collapse
I may have stopped updating one to early. Anyway, my watch updated by itself last night all the way to MM, now it is stuck again. I'll have to search and see if there is a way to stop the automatic OTA updates.
I have seen where people have flashed only the kernel. I have not. At this point, it would be nice just to keep it at the last LP. I'll let you know if I find anything. Thanks.