Develop Bugs

Multifunction Adapter

Does anyone know if this adapter would work with the GN?
http://www.amazon.com/HTC-Multifunction-Adapter-T-Mobile-Shadow/dp/B001QD3MQE/ref=cm_cmu_pg__header
I want to have the phone output audio while being simultaneously being charged.
I would love to have the official car dock, but it is nowhere to be found (yet).

No. It will not.
Why not just plug something into the headphone port and the power into the USB cable like you are supposed to do?

I'm looking for something simple. Just drop it on a dock and go.
IPhones have countless docks, my pre has the touchstone.
I suppose I could just connect through Bluetooth for audio and plug in a charging cable in the meantime until that GSM car dock comes out.

staticx57 said:
No. It will not.
Why not just plug something into the headphone port and the power into the USB cable like you are supposed to do?
Click to expand...
Click to collapse
Why won't it work? I have been looking for something exactly like this to make a custom portrait desktop dock that has audio out. The problem is the headphone jack is on the bottom and covered when in this position... any suggestions on what I could use for this situation?
*edit* Looks like it isnt a micro usb so it definitely wouldnt work then...curious though, does anything like this exist that would work with gnex?
Sent from my Galaxy Nexus

There's no way for it to work on a Samsung phone because those old mini USB slots on those HTC phones are proprietary 11-pin ExtUSB ports. Normal USB mini/micro only has 5 pins. HTC wanted to be cool and add extra pins to the USB port so that they wouldn't have to add a headphone jack to the phone. To my understanding, this was unpopular because you had to buy extra hardware just to get a headset working.

Motorola Atrix Lapdock and Galaxy S III

Has anyone connected their Galaxy S III up to a Motorola Atrix Lapdock?

If I remember well, the Motorola lapdock uses a HDMI plug to connect with the Atrix.
GS3 doesn't have one, you should get a MHL/HDMI convertor. Don't know if it'll work as a native HDMI plug will do.
If someone have both, it could be intereting to see if that work

So I'm going to dust this thread off a bit because this is the project I'm looking to work on -
I've ordered an Atrix Lapdock for my Bionic (very simple mod to dock the bionic) but as my personal phone is an S3, I'd like to use the lapdock with it primarily while still having the option to dock the bionic while on the go (I carry both phones). (While I'm at it, I'll probably look to get an hdmi micro extension cable and usb-micro-male to usb-A-male extension and try and use the lapdock as the base station for the Samsung Slate 7 PC i barely use since the interface is so poor)
Here's what I've gathered by reading various threads.
Lapdock:
The Lapdock will work with any HDMI source as seen in other threads (ie connecting to a PS3 via hdmi female micro to hdmi male standard adapter, $4 part from dealextreme). Others have posted how they can use the lapdock as a self powered hdmi external monitor with their laptop (very cool usage btw considering it's size)
Droid Bionic:
easily docks to the Atrix version of the lapdock by simply rotating the hdmi/micro usb connectors 180degrees in their sockets since they're piped in with short cables.
Galaxy SIII / S3 (mine is the T999):
here's where it gets tricky.
As I've gathered about the 11pin micro usb port (on the S3 and shared by the Note 2):
the original 5 pin MHL standard was ditched in favor of the 11pin MHL type connection. this in theory would allow the use of hdmi output with simultaneous usb otg and charging capabilities.
reviewing this thread here: (showthread.php?t=1953061&page=2) one can see that an OTG cable was modded with a simple resistor to allow for charging - member triff (the OP) was able to get this going and noted the log he got when the cable was plugged in reported 'hdmi fail' which leans to failing to initiate an hdmi connection... later in the thread member MRBR7 alludes to having an hdd running to view while charging on the OTG cable - his post is a bit vague as to whether he did the mod on an OTG cable or an HDMI cable.... i'll have to follow up.
finally, the posts in this thread (first 12 pages are a quick read showthread.php?t=1741583&page=12) provide resistor values and some close ups of the boards for the 11 to 5 pin adapter as well as what I thought was a list of pins for the 5 pin MHL.
I'm really trying to be purposefully clear in this thread as to my findings because it seems there are too many vague threads out there regarding the functionality; simply missing a letter or punctuation in a thread can turn a sure thing into a vague post...
another avenue is the official samsung galaxy note 2 "smart dock" which has 3 usb ports, in additon to an hdmi output and charging input - since this is sold out in the US (and due to PAL vs NTSC Standard I am hesitant to order from germany) it'll be a while before I can personally buy and test one (unless i can find one locally somehow). this seems like the best bet for a dock which can be hacked or adapted to interface the s3 with the lapdock.
my ideal final outcome of this thread would be to have a small cable or interface box which i can plug into the s3 to enable hdmi output + usb otg + charging. that trifecta would connect via a single micro-usb to the device (11 pin) and have an output of a female usb (A or micro, either can be adapted) and either a male or female standard hdmi (again, both of which can be adapted). this cable could enable the phone to be used as an impromptu desktop, carputer, lapdock brain etc...

Lapdock software required...
Sent from my SGH-T999 using xda premium

deedscreen said:
Lapdock software required...
Click to expand...
Click to collapse
What do you mean by that?
The Atrix Lapdock is internally nothing but an 1366x768 HDMI LCD monitor with (rather poor) speakers and an USB-Hub on which a keyboard/touchpad and two free USB-ports are connected to. The monitor and the USB-hub have to be simply attached to any device which supports HDMI-output and USB-OTG via (slightly uncommon) HDMI- and USB-OTG-plugs.
There is no software running on the Lapdock (it is actually completely dumb) and there is no need for any specific SW on the connected device (might be nice to have something like webtop running but it is not necessary).
The S3 works flawlessly with the keyboard/touchpad/USB-hub using a USB-OTG-Adapter and with the HDMI-monitor via an MHL/HDMI adapter cable. The tricky part is only to get both simultaneously and possibly even charge the S3 from the Lapdock. For that purpose I use as long as there is no combined MHL-HDMI/USB-OTG-adapter/dock available (as described in the thread and page already indicated above: showthread.php?t=1741583&page=12 ) the allshare cast dongle and a cheap OTG adapter. You can use office apps, watch videos, play games etc. without any problem. You can check out
ecx . images-amazon . com/images/I/712%2BAbT1u3L.png
(no links for me yet)
to see how that looks like...

a32quaeler said:
What do you mean by that?
The Atrix Lapdock is internally nothing but an 1366x768 HDMI LCD monitor with (rather poor) speakers and an USB-Hub on which a keyboard/touchpad and two free USB-ports are connected to. The monitor and the USB-hub have to be simply attached to any device which supports HDMI-output and USB-OTG via (slightly uncommon) HDMI- and USB-OTG-plugs.
There is no software running on the Lapdock (it is actually completely dumb) and there is no need for any specific SW on the connected device (might be nice to have something like webtop running but it is not necessary).
The S3 works flawlessly with the keyboard/touchpad/USB-hub using a USB-OTG-Adapter and with the HDMI-monitor via an MHL/HDMI adapter cable. The tricky part is only to get both simultaneously and possibly even charge the S3 from the Lapdock. For that purpose I use as long as there is no combined MHL-HDMI/USB-OTG-adapter/dock available (as described in the thread and page already indicated above: showthread.php?t=1741583&page=12 ) the allshare cast dongle and a cheap OTG adapter. You can use office apps, watch videos, play games etc. without any problem. You can check out
ecx . images-amazon . com/images/I/712%2BAbT1u3L.png
(no links for me yet)
to see how that looks like...
Click to expand...
Click to collapse
Interesting..especially for the 89$ price tag. Long as one can deal with S3 not charging its a simple setup no ?

xManMythLegend said:
Interesting..especially for the 89$ price tag. Long as one can deal with S3 not charging its a simple setup no ?
Click to expand...
Click to collapse
Well, I got the Lapdock for less than 70 Euros and I think that is really great value since it is very well build and versatile... the allshare cast dongle is a bit overpriced (currently it is about 55Euros here) for an adapter-replacement but if you need it for different use cases (I mainly have it for a small LED-beamer) it might be worth it.
You can charge the S3 from one of the USB-ports of the Lapdock using a micro-USB cable (as long as the dongle or any other device is connected to the Lapdocks HDMI-plug - that is what signals the Lapdock to power up), but you can not simultaneously use the MHL/USB-OTG then. So it is nice for watching movies from your S3 on the Lapdock-screen (btw. the sound works fine as well) while re-charging the S3 but for "office" work with kb/touchpad you have to replug the OTG-cable. Actually I'm quite impressed with the relatively low power consumption of the allshare cast connection - so that is not a real problem IMHO. There might be people out there to solder the right resistors into OTG-adapter cables to allow both...
One disadvantage is obviously that you have this "bulky" (it is actually lightweight but still bigger than a simple adapter) dongle on the Lapdock. The big advantage over a dock is that you can more or less freely move around the S3 while using this combination.

deedscreen said:
Lapdock software required...
Sent from my SGH-T999 using xda premium because i'm a moron and don't know what i'm talking about
Click to expand...
Click to collapse
you obviously don't know anything about the lapdock, so please, hang around, do some searching and learn about what it is before posting vague comments that ruin the integrity of a factual thread.
xManMythLegend said:
Interesting..especially for the 89$ price tag. Long as one can deal with S3 not charging its a simple setup no ?
Click to expand...
Click to collapse
google 'bens outlet' (a 1saleaday company) and you can pick one up for as little as $50usd! assuming it actually ships out, but worth it for a spare monitor project at the very least... - and yes, not a hard setup at all - the first use in my mind would be just to have a full size screen on the go, however to have a cable capable of mhl/hdmi + usb otg + charging would turn the dock into a powerhouse android laptop using 4g internet etc... (it'll give the chromebook a run for it's money)
a32quaeler said:
the allshare cast dongle is a bit overpriced (currently it is about 55Euros here) for an adapter-replacement but if you need it for different use cases (I mainly have it for a small LED-beamer) it might be worth it.
Click to expand...
Click to collapse
what's this LED beamer? (i'm just intrigued)
a32quaeler said:
You can charge the S3 from one of the USB-ports of the Lapdock using a micro-USB cable (as long as the dongle or any other device is connected to the Lapdocks HDMI-plug - that is what signals the Lapdock to power up), but you can not simultaneously use the MHL/USB-OTG then. So it is nice for watching movies from your S3 on the Lapdock-screen (btw. the sound works fine as well) while re-charging the S3 but for "office" work with kb/touchpad you have to replug the OTG-cable. Actually I'm quite impressed with the relatively low power consumption of the allshare cast connection - so that is not a real problem IMHO. There might be people out there to solder the right resistors into OTG-adapter cables to allow both...
One disadvantage is obviously that you have this "bulky" (it is actually lightweight but still bigger than a simple adapter) dongle on the Lapdock. The big advantage over a dock is that you can more or less freely move around the S3 while using this combination.
Click to expand...
Click to collapse
all very cool - I'm thinking of ordering the allshare dongle just to try this out until the smartdock gets back in stock to hack it apart .. I'll probably order an 11pin mhl in the meantime too. I have a 5pin mhl, not sure what I can do with it without the adapter (i'll probably bundle it with my galaxy nexus and sell it all)
@a32: on a side note, i broke down and bought a Note 2 yesterday haha, so I'll probably be continuing this project with the Note2, (tmo just happened to have some in stock haha) I'm putting my week old S3 up for sale soon, but this project is still on my radar!

teshgnex said:
you obviously don't know anything about the lapdock, so please, hang around, do some searching and learn about what it is before posting vague comments that...
Click to expand...
Click to collapse
The S3 would need the lapdock .apk for certain functionality... calm down, I've owned enough Motorola Android devices to know what I'm saying...
Thats all... Ben's Outlet would be good plus All4Cellular sells it with the extenders...
Its out of stock now but you can get the extenders separately at a hefty price:
www.all4cellular.com/motorola-atrix-4g-laptop-dock-hdmi-upgrade-kit.html
The hefty priced cables are below, but it is worth the cost:
www.all4cellular.com/motorola-atrix-4g-upgrade-kit.html

deedscreen said:
The S3 would need the lapdock .apk for certain functionality... calm down, I've owned enough Motorola Android devices to know what I'm saying...
Click to expand...
Click to collapse
Sorry to snap, but if you've been on enough forums, you begin to notice that comments like yours are just add to confusion when unsubstantiated.
Any phone without a 'web top' mode or apk would obviously not work similar to the webtop mode that Motorola intended, however it'll still work, perfectly in fact, because this connection project is akin to hooking up your phone to a tv or monitor and using a usb mouse and keyboard to control it, albeit it's portable, like the padphone.
If you have any ideas as to how one could hookup both mhl/hdmi and usb/otg with charging I'm all ears (the real breakthrough would easily be seeing a US version T999 or similar running with the Smart Dock for the Note 2
Another thought to throw out there is whether this finished product could look similar to the padphone concept: a pocket for the phone to slip into, docking connector inside, basically self contained
As for those extension cables posted, places like monoprice and dealextreme have much better prices and selection, granted I'm just going those links on my phone - i don't understand how those are considered 'adapters' when all they do is extend the port
Sent from my SGH-T889 using xda app-developers app

Silly question but why would you need software when your using it as a monitor, keyboard, mouse, usb hub & charging?

djashjones said:
Silly question but why would you need software when your using it as a monitor, keyboard, mouse, usb hub & charging?
Click to expand...
Click to collapse
You don't.
... that's what we posted already. The webtop SW on some Motorola devices starts a specific desktop and window-manager on your phone when connecting to the lapdock. It may facilitate the use of the apps on the phone via the Lapdock (resolution/size/... of apps in windows etc.) but you do not need it to work with the S3 on the Lapdock.

awesome! im very tempted to get one but in the UK they are still expensive

teshgnex said:
what's this LED beamer? (i'm just intrigued)
Click to expand...
Click to collapse
A bit off-topic: It is an ACER C20 I own for nearly 2 years now. Like this one:
ecx . images-amazon . com/images/I/41aXbNerVoL._SL500_.jpg
It is out of stock anyway, but I could "partly" recommend it:
It has the size of a phone, a built-in battery and - most important - lots of inputs (mini HDMI (HDCP), D-Sub (24-pin Universal), Composite Video/Audio (2.5mm 4-pin mini jack), micro USB (Typ AB), micro SD Card (SDHC)) + Audio out & speaker. It plays media from internal storage/SD card but that internal media-player is crap. It is however extremely mobile and together with movie players on modern phones like the S3+cast-dongle - or any tablet with HDMI-out or a device with Composite A/V out (e.g. old Nokias) - a nice device e.g. to entertain kids on travel or showing pictures while visiting the grandparents or alike. On the other hand, it is not really bright at all (actually you have to be in a very, very dark room to use larger screen areas) and the battery lasts often only 1/2 hour (but you can charge it with 5V from USBs or use it while on the mains adapter).
It works really nice with the S3 + allshare cast dongle (that's what I bought the dongle for in the first place), has a descent image quality (848x480 pixel) and accepts up to 1080i HD over HDMI as input signal for downscaling but for the dongle the input is of course limited 720p. It does NOT work with the S3 using the cheap (chinese) USB-MHL/HDMI-adapter with the long red cables (somewhere discussed here as well) since that one provides 1080p30Hz (at least to my TV - on which it works) and the projector obviously can't sync to that.
Back to the topic: that cheap HDMI-adapter for S3 works not very well with the Atrix Lapdock; you get an image but it is vertically squeezed. Again: the Lapdock and the S3 + cast dongle go together extremely well.

That led projector sounds pretty cool, I've waffle'd on buying one various times but can't say I've had a particular need other than for the fun of it hah
a32quaeler said:
Back to the topic: that cheap HDMI-adapter for S3 works not very well with the Atrix Lapdock; you get an image but it is vertically squeezed. Again: the Lapdock and the S3 + cast dongle go together extremely well.
Click to expand...
Click to collapse
So I'm guessing you've tested this, but with the hdmi cable and the screen rotation turned on, the device still shows up in portrait? Unless I'm reading that wrong and you mean it's width wise video but looks like a 4:3 video on a 16:9 widescreen?
I wonder if that behavior is present with the official adapter...
So to return to the method of the allshare dongle, does it look like image 1 as i posted?
I recall you mentioned the dongle's hdmi signal is what triggers the docks micro usb port for kb/mouse control and charging, so for clarity i drew the wiring method up.
The next two wiring diagrams are what I'd expect to do as i finalize what the connection should/could look like...
I'm always in for feedback on streamlining the connections - the simple yet two part method will be just having the official smart dock, assuming it works with the s3, powered with one usb port, hdmi to hdmi mini and usb micro to the usb port, though maybe modify the output to delete charging power from the kb/m micro usb port...
Sent from my SGH-T889 using xda app-developers app

teshgnex said:
I recall you mentioned the dongle's hdmi signal is what triggers the docks micro usb port for kb/mouse control and charging, so for clarity i drew the wiring method up.
Click to expand...
Click to collapse
Sorry, don't have much time and will have a look at your drawings later... The presence(!) of a device connected to the HDMI is detected by checking for a "Ground"-connection of one of the HDMI-pins (from googling I remember it to be HDMI-DDC/CEC) - that's what powers up the Lapdock (and activates the USB-Ports). No need for an already powered device on that HDMI port. The problem is however that there are many HDMI adapters/extension cables out there which do not pass that specific wire/connection and then the Lapdock will not react when using those. There is however no need to buy these overexpensive Motorola cable sets (those prices are unbelievable!)... my adapters & cables cost in total about 9 Euros.
+5V on the OTG-USB cable from the peripheral device (=Lapdock) to the host is not "liked" by most hosts (the S3 did not really react on it but it is probably not a good idea anyhow) so I cut the 5V red wire of the micro-USB(female)-to-micro-USB(male)-cable. On the latter you need something to signal the S3 the OTG mode (pin 4 grounded to 5). I do that quite stupidly using additional USB->OTG-adapters but you would have to take care of that in your MHL/OTC combi adapter with resistors etc. anyhow.
The "chinese" Adapter is vertically squeezed. The S3 goes into the correct HDMI-out mode including the (stock) homescreen to be usable in landscape mode - that is not a problem. Probably the 1080p30Hz mode is not well understood by the Lapdock and/or the adapter does not correctly "negotiate" the right resolution-/display ratio with the display or the quality of the sync signal from the adapter is really bad. That chinese adapter is not too bad for Full-HD TV sets but unusable for anything else. I did not try the official one. The Lapdock works however well with the dongle.

This info is much appreciated. I took the dive and ordered a lapdock from bensoutlet.com for $50 to play with. The regular one is $60 - but the keyboard that adds Hebrew letters was $10 cheaper. I figure the lettering doesn't hurt anything so I'd rather save the $10.
If anybody figures out how to simplify the connections, or perhaps someday enable MHL out + USB host with this thing - please post back.
Right now - I spent an additional $6 on dealextreme.com to get a microHDMI (female) to HDMI male adapter, and a micro usb female to male adapter so I can try to use the keyboard.
The result is going to be pretty cluttered, but I figure $50 is cheap for a portable, self powered HDMI monitor that could also power stuff from it's ports.

teshgnex said:
The next two wiring diagrams are what I'd expect to do as i finalize what the connection should/could look like...
Click to expand...
Click to collapse
Your drawing No 1 is what I use (see below). No 2 is how it should be indeed (but where is the "modded cable" coming from?). While No 3 will not help you since only the presence of a shortened HDMI-CEC pin (+ opening the display a bit) will power ALL the USB-ports including U1+U2 (that activity mode of the Lapdock is indicated by a small white LED next to the touchpad) - so there is no "pre-power" available. But (again) anything that provides that ground contact on the HDMI-plug will do the trick... I actually have one 90degree HDMI-adapter (don't know how to call it in English), which does exactly that and shortens those pin(s) and simulates to the Lapdock the presence of a device (I assume that is NOT on purpose but it works with a second, identical adapter as well). Don't take me wrong you do not need that one if you conect a device (any) directly to the microHDMI-to-HDMI adapter but it is needed when you use HDMI extension cables (etc.) that do not pass all wires to the HDMI device.
I attached some pics how I wire that thing. Pic 1: the micro HDMI plug on the Lapdock is turned by me by 180deg just to make a bit more room for the microHDMI(fem)toHDMI(male)-adapter. You may directly attach the dongle to it (it is relatively stable and easy to carry around - pic 2). That's what one could call "entertainment mode" since you may want to watch videos etc. this way. But than you have not enough space for the microUSB-cable for kb/mouse. That is what I use the 90deg-adapter for. This adapter alone signals already the Lapdock to power up (no other HDMI-cable or adapter I own does this). Back to pic 1: The microUSB(fem)-to-microUSB(male)-cable has the red 5V wire cut. The microUSB-to-USB + USB-microUSB-OTG(!) adapter is there only to signal the OTG-host mode for the S3. The stuff on the right are things you may use on the free USB-port.
That strange device with the mobile speaker attached to its headphone jack has to be explained: it is a (5 Euro) "USB sound card". That is a bit odd... the Lapdock has stereo speakers which are working well (but not great) and the audio-output via HDMI(cast) to the Lapdock works perfectly (sound is ok and in sync when watching videos & you can control volume etc. from the S3 or the Lapdock keyboard) but the allshare cast SW on the S3 does not allow you to plug in a headphone or connect a bluetooth audio-device to the S3 for output of the video(!)-sound. You can use headphones for mp3-player music while using an HDMI display etc. but when you switch on a video you have to remove headphones otherwise the allshare connection stops. There might be two reasons 1: HDCP, 2: there is a small lag in video display from the wireless transfer protocol and the audio stream is equally lagged on purpose to be well in sync with the video stream. You may want to bypass that artificial restriction because the Lapdock has NO headphone jack ... and you can by using such a "soundcard" which is fully supported by the S3 but the sound is then indeed a bit "in advance" of the video stream.
Less exotic devices you can attach are external disks/pen drives or even game controllers (all of them work)... Pic 3 shows you how I wire it for "productivity mode"

P0ll0L0c0 said:
This info is much appreciated. I took the dive and ordered a lapdock from bensoutlet.com for $50 to play with.
Click to expand...
Click to collapse
Thank you. 50$ ! When they are as cheap go and get some (or better get many)! The Lapdock is really, really useful and works with many devices.
I originally bought it for the Raspberry Pi but I use it as well with an Archos A80G9 android tablet (not so often since the tablet is big enough anyhow) which has seperated (mini)HDMI and USB-OTG connectors (as it should have been done for all mobile devices including the S3) and used it for my "old" Nokia N8 (miniHDMI as well). In that case USB-OTG does not work since the N8 does not support USB hubs but you can chrge it and watch movies on the Lapdock display with it (in the train ...). The RasPi is powered via the same cable that is used for kb/mouse. In that cable I did obviously not cut the 5V wire. The power the Lapdock provides this way is sufficient to operate the RasPi (+ wifi dongle) ... about 1A is needed for that. So it should be possible to use that power via that OTG microUSB port for the S3 as well ...

What abot the EDD-S20E dock won´t that work with the lapdock ???
Problem is the dock is useless for my next device in 2 - 3 Years....
The allshare cast dongle might stay usefull even with the next gen of android phones....

USB OTG cable with charging - is that possible?

While researching ability to use USB DAC while charging the phone in the car I found this video. The guy clearly says that tablet is charging while accessing all those accessories via USB OTG. Similar cables are found on ebay, called "USB OTG with power".
The big question is: would the Galaxy S3 actually charge while using USB DAC at the same time? It should be possible, but I don't have the phone yet (still considering it), nor do I have the cable, nor a USB DAC In theory it should be the same with any accessory - can someone actually confirm either way, whether phone can or can't charge in USB OTG mode with similar cable? This video shows similar setup on Galaxy S (only it's normal OTG cable, USB hub, usb Y-cable and card reader) and it's definitely charging while mounting USB devices! Will S3 do the same?
I fear that upgrading from Galaxy S with voodoo control of Wolfson chip to north-American S3 with worse audio path might not suit me if there's no way to power the phone and use external DAC at the same time in the car... I hope there is a way... I appreciate any advice and opinions.

It's a first time I see such cable...All I read was people saying it's impossible in the first place. Well, hopefully in 2 weeks I'll be able answer your question

midirt said:
While researching ability to use USB DAC while charging the phone in the car I found this video. The guy clearly says that tablet is charging while accessing all those accessories via USB OTG. Similar cables are found on ebay, called "USB OTG with power".
The big question is: would the Galaxy S3 actually charge while using USB DAC at the same time? It should be possible, but I don't have the phone yet (still considering it), nor do I have the cable, nor a USB DAC In theory it should be the same with any accessory - can someone actually confirm either way, whether phone can or can't charge in USB OTG mode with similar cable? This video shows similar setup on Galaxy S (only it's normal OTG cable, USB hub, usb Y-cable and card reader) and it's definitely charging while mounting USB devices! Will S3 do the same?
I fear that upgrading from Galaxy S with voodoo control of Wolfson chip to north-American S3 with worse audio path might not suit me if there's no way to power the phone and use external DAC at the same time in the car... I hope there is a way... I appreciate any advice and opinions.
Click to expand...
Click to collapse
HI. I Got it working on SONY XPERIA S now i will play with GALAXY SII AND SIII , check my siganture and website --> follow me i hope i can help

sonic_boom said:
HI. I Got it working on SONY XPERIA S now i will play with GALAXY SII AND SIII , check my siganture and website --> follow me i hope i can help
Click to expand...
Click to collapse
Looks like it's possible on some devices, but not with Galaxy and Nexus family... But it would be great if you can confirm that, so let me know if you can try it. Thanks.

Finally got the cable.
The result - nope, doesn't charge

Maybe the "Allshare hub" could do what your asking for?

sonic_boom said:
HI. I Got it working on SONY XPERIA S now i will play with GALAXY SII AND SIII , check my siganture and website --> follow me i hope i can help
Click to expand...
Click to collapse
Sonic, any luck with your friends phone? Really looking foward to your results :fingers-crossed:
Do you have part #s for the variable resistors in your samsung post or at least where you got them from? I would be willing to try some things out if I could find the right pieces. What I really want to get my hands on is the MHL adapter that was shown off with that spider laptop at IFA a couple weeks ago..

SUCCESS!!! I can confirm that this USB OTG cable (http://ebayitem.com/190710044655) DOES CHARGE MY GALAXY S3! I plugged in USB cardreader with SD card into the phone through this cable (it lit up and card is fully readable), then plugged USB cable end into PC and phone showed a charging icon! Moreover, after waiting for 5 min. with screen off (cardreader still glowing blue and working) battery has gone up from %72 to %75 (and while I was writing this, to 78%), so it is indeed charging! Yay! It probably won't get up in the car, where just phone alone is "not discharging" at best from the car adapter, but at least it should allow me to listen to music with quality DAC and use navigation without (or with minimal) discharging.
I have not tested it with USB DAC that I intend to use for my car (Behringer UCA222), because I have to go out and buy it. Hopefully it works. Anyway, this cable definitely works with simultaneously charging my north-american Samsung Galaxy S3 (from Bell Canada) while powering USB cardreader!
Somebody else has mentioned that another cable (http://ebayitem.com/120980364117) also worked in his Galaxy S2.

I bought Behringer UCA222 USB DAC and tested it in my car with the USB OTG cable with power that I mentioned. It works great! And the phone is indicating a charge. Sometimes when first playing music after plugging the device it sounds like fast forward for a few seconds (I guess clock rate mismatch or something similar), but after the presumably clock is locked it plays perfectly fine.

midirt said:
SUCCESS!!! ...
Click to expand...
Click to collapse
That is outstanding..gonna order one of these guys right now.
Here is a better link for all the ebay listings. Be aware of the differences, MicroUSB adapters would allow you to use your existing charge cable to plug into it while the standard USB would require you to be very close to the charger or have a USB A-A cable to attach to a power source.
http://www.ebay.com/sch/i.html?_trk...Host+OTG+Cable+++USB+power&_sacat=0&_from=R40

Jeremy.Stewart85 said:
That is outstanding..gonna order one of these guys right now.
Here is a better link for all the ebay listings. Be aware of the differences, MicroUSB adapters would allow you to use your existing charge cable to plug into it while the standard USB would require you to be very close to the charger or have a USB A-A cable to attach to a power source.
http://www.ebay.com/sch/i.html?_trk...Host+OTG+Cable+++USB+power&_sacat=0&_from=R40
Click to expand...
Click to collapse
The problem is that apparently not all of those cable work in terms of charging the phone. People say mostly that it doesn't work. The only guy mentioned success is with the cable I bought, but he then confirmed it with another, more convenient cable. I have the one that needs a USB extension cable to reach the charger, but it's about a buck on ebay, so no problem there. But not all cables work this way: most reportedly will allow you to power USB accessories but not charge the phone.

I found that this configuration works for charging while in USB HOST mode:
S3 -> standard otg cable -> Powered USB2.0 HUB -> devices (keyboard, usb dac, usb hdd...)
The only catch is that the hub must be powered before you plug in the phone or the phone will try to power the hub and will never enter charging mode. I'm using this setup in my car and it works perfectly. As long as I start the car before plugging the phone, we are good to go.
I only confirmed this works with AOKP JB builds. No idea about other roms/kernels. Hopefully this helps someone.

midirt said:
The problem is that apparently not all of those cable work in terms of charging the phone. People say mostly that it doesn't work. The only guy mentioned success is with the cable I bought, but he then confirmed it with another, more convenient cable. I have the one that needs a USB extension cable to reach the charger, but it's about a buck on ebay, so no problem there. But not all cables work this way: most reportedly will allow you to power USB accessories but not charge the phone.
Click to expand...
Click to collapse
I got mine in the mail today (ordered 10/16) and tried it out as soon as I could. I can confirm it charges and allows for OTG at the same time. This is the auction I bought from: http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=251127542280&ssPageName=ADME:L:eek:U:US:3160

Hello y'all. I'd like to ask your attention to this thread, especially but not limited to sonicboom and others, I really could use some help.

[Q] Moto 89526N Dock on the S3

Will this dock work with the S3?
Motorolla Dock 89526N
If not why?

No. The Motorola Dock (at least the one with the model number you specified) has both the Micro-USB AND the Micro-HDMI connections in the dock connector. If it weren't for the inclusion of the Micro-HDMI port, then it MIGHT be usable... but it's hard to say without having something like that on hand. But as it stands, the one you mentioned wouldn't be usable.

elementaldragon said:
No. The Motorola Dock (at least the one with the model number you specified) has both the Micro-USB AND the Micro-HDMI connections in the dock connector. If it weren't for the inclusion of the Micro-HDMI port, then it MIGHT be usable... but it's hard to say without having something like that on hand. But as it stands, the one you mentioned wouldn't be usable.
Click to expand...
Click to collapse
Have you come across anything like this? I know the Note 2 has a dock similar to this, however I have heard it will not work "Fully" with the the 4.1 firmware. We will have to wait till 4.2 for it to work. I am looking to replace multiple laptops with cell phones. Bluetooth works ok, however we might run into issues with unpairing and pairing again in multiple rooms. USB keyboard and mouse would be the way to go. As well as HDMI out for monitors.

I spoke with Mike M from MonoPrice tech support and as he put it if there is a demand for this type of cable they will create one.
The cable will have:
Micro USB Male Out (to your phone)
A Female Type A USB Data (for mouse, keyboard, hub, etc)
A Mini or Full size HDMI Out ( TV or monitor)
And a Micro USB charge for powering extra devices.
There are tons of benefits on using USB rather than Bluetooth for keyboards and mice. Especially when you have multiple phones coming and going from one station.

MHL Cable for the Note

Hi. So I found this cable for the Note on eBay.
It seems a good item because it doesn't require the adapter or external power. Has anyone tried it, or is it more worth while to go for the original adapter? TIA

Gigarant said:
Hi. So I found this cable for the Note on eBay.
It seems a good item because it doesn't require the adapter or external power. Has anyone tried it, or is it more worth while to go for the original adapter? TIA
Click to expand...
Click to collapse
I'm not sure why you'd want one without the usb cable for power though, cuz if you're outputting your display to your TV then it's going to drain a lot of power.
Unless you only want to show say a picture, or a short video it might be okay, but if you want to output say a whole movie, you're going to want to provide your phone with power at some point.
I've recommended an mhl cable in the past. It might suit you if you're looking for a nice, compact cable with hdmi and usb (for power).
But if you're dead against one with a power cable then feel free to give your linked one a try and report your findings.

little-vince said:
I'm not sure why you'd want one without the usb cable for power though, cuz if you're outputting your display to your TV then it's going to drain a lot of power...
Click to expand...
Click to collapse
Yeah, but i got the impression it would draw power from the TV by itself. I may be wrong about that...its not that I'm dead against a cable that needs power, more that I'm thinking about portability and something to add a bit more value should I ever sell the Note. And admittedly for the last one a genuine OEM adapter would be the best option, but they are gorram expensive.
Considering I have to buy an HDMI cable for my laptop, I might try a generic adapter, see how that works, and then try this cable if I have the spare cash in the future.

Hi,
So I have an update for this; recently I bought one of the cables as above out of curiosity, and surprise surprise... It didn't work. When I connected the Note to the TV with it, it just flashed up 'USB connected' and then 'USB not connected' in the status bar. This is because of the obvious reason; that you need a conventional adapter with a USB-connection for external power. Also, the seller of this cable claimed that the TV in question needs to be MHL (not just HDMI) compatible for it to work. So essesntially you do in fact need a conventional Samsung (or generic copy) 5-pin HDMI adapter to get your Note's display on your TV.
I think that resolves the question. Oh, one more thing: you need a TW-based ROM for HDMI connection. Don't forget...