Related
Hello, I have bricked my S8500. I can go to the download menu. The problem is that I can't install properly USB drivers , or maybe it is USB cable that is wrong, the USB cable is from nokia and model is : CA101. Even when the phone was working ok computer couldn't see my wave , and I don't know why... So the problem is that when I go to the Download menu my computer detects all the drivers and everything is alright... And when I hit download I get this.
Download Start Ch[0]
BootLoader 1703.9KB OK[0.7s]
Dbl 281.5KB OK[0.8s]
Wait reset !!
Serial port detect error!
And after Wait reset my computer just didn't recognize my phone anymore, and that's why it has been bricked at the begining. Could anyone please help me? I tried different USB drivers, different PC. Nothing helps :{{{ Please guys, help me.
Maybe it is because my USB cable isn't from original wave, or no?
Nipit said:
Hello, I have bricked my S8500. I can go to the download menu. The problem is that I can't install properly USB drivers , or maybe it is USB cable that is wrong, the USB cable is from nokia and model is : CA101. Even when the phone was working ok computer couldn't see my wave , and I don't know why... So the problem is that when I go to the Download menu my computer detects all the drivers and everything is alright... And when I hit download I get this.
Download Start Ch[0]
BootLoader 1703.9KB OK[0.7s]
Dbl 281.5KB OK[0.8s]
Wait reset !!
Serial port detect error!
And after Wait reset my computer just didn't recognize my phone anymore, and that's why it has been bricked at the begining. Could anyone please help me? I tried different USB drivers, different PC. Nothing helps :{{{ Please guys, help me.
Maybe it is because my USB cable isn't from original wave, or no?
Click to expand...
Click to collapse
I too use Nokia table to flash my samsung wave. If your phone was able to connect to Kies prior to flashing there should be no issues.
When you flash for 1st time you always get that error. Pls try once again and you shd not face any issues.
Datta
No, I wasn't able to connect to kies. I got a USB cable from original xperia x10, still same issue... Can someone tell me what to do? I downloaded a lot of drivers, but maybe there is some special driver? :/
The problem usually goes away for me when flashing from a freshly booted pc, so try restarting one of your computers for flashing and try again.
Have done that too... Any advice? :/
Hello!
First kill all Kies Processes (in the Task Manager)
Second launch Multiloader and try to flash
When it says Serial Error, just do Port Search again, and it should work
That's what I did when I had my Serial Port error ^^
Hope I helped you
Download Start Ch[0]
BootLoader 1703.9KB OK[0.7s]
Dbl 281.5KB OK[0.8s]
Wait reset !!
Serial port detect error!
---------------------------------------------
Just after this message, without quit Multiloader:
Phone on DOWNLOAD MODE try this:
Uncheck Boot, unplug USB Cable from Phone and Plug it again, You will see Download actived in Multiloader, Just clic on DOWNLOAD. And your Flashing will be continued....
----------------------------------------------
Sory For my english.
Still the same **** :{{{ Anymore advices guys?
Darkminus said:
Hello!
First kill all Kies Processes (in the Task Manager)
Second launch Multiloader and try to flash
When it says Serial Error, just do Port Search again, and it should work
That's what I did when I had my Serial Port error ^^
Hope I helped you
Click to expand...
Click to collapse
You didn't understand me very well. The problem is that when I hit download my computer suddenly loses USB connection and shows my phone as unknown device, that is the problem why I bricked my phone. Do anyone knows how to make my pc see my samsung wave?
Nipit said:
Download Start Ch[0]
BootLoader 1703.9KB OK[0.7s]
Dbl 281.5KB OK[0.8s]
Wait reset !!
Serial port detect error!
Click to expand...
Click to collapse
Same thing happened to me. After this, you shouldn't disconnect you wave, but to wait, and click search port again. If there is no port again, tru with different multiloader (mine was v5.65), and there is again same problem, try with another computer with preinstalled USB drivers.
The good thing is that your phone still enters boot mode. If it wasn't the case, then it would be a total brick.
Best regards
Nipit said:
You didn't understand me very well. The problem is that when I hit download my computer suddenly loses USB connection and shows my phone as unknown device, that is the problem why I bricked my phone. Do anyone knows how to make my pc see my samsung wave?
Click to expand...
Click to collapse
No, you didn't understand this flashing process. Most important thing here is to avoid interrupting of connection between computer and phone, even in serial port error. You need to search port again, or to change things that I mentioned above.
You hit download, then bootloader is loaded. It is absolutely normal in this algorithym to reset phone (wait reset). Then our error appears in port error. That is the time when you should click port search again, and when it finds it again (it will) click download button. Thats how it was in my case already 4 times.. Hope I helped.
Best regards
I have told that I reinstalled a lot of drivers and tried different PC's, nothing helps. I tried about 3 or 4 versions of multiloader still same result :/ I don't know what to do anymore... Please any advices? Maybe someone had the same issue?
I don't really know what happened. We switched our cables with my friend again, and I tried to flash with Nokia cable. And everything went okay for the 1 time. No errors, no nothing, no Unknown USB device problem. This is really strange. Thank you for you help friends :}
datta.ca said:
I too use Nokia table to flash my samsung wave. If your phone was able to connect to Kies prior to flashing there should be no issues.
When you flash for 1st time you always get that error. Pls try once again and you shd not face any issues.
Datta
Click to expand...
Click to collapse
i have bricked my s5330 please help
no download mode or even recoverymode please help
I got the same problem too. Windows detects it as Unknown device.
Anyway to fix it? :crying:
[email protected] said:
I got the same problem too. Windows detects it as Unknown device.
Anyway to fix it? :crying:
Click to expand...
Click to collapse
Try to install driver manually from windows driver menu
Just installed "S8500-Driver-V5_02_0_0" now it's working since I wanted to flashback my friend's Wave from Bada2 to v1
I was trying unblocking bootloader. However, when I plugged in my phone, my computer can't detect my driver downloaded.
So I tried several times unplug and plug and eventually I can't turn on my phone.
And now when I connect to my computer, there is just a qhsusb_dload drive appeared.
No idea how to fix this.....
I have the same problem but not same cause, No charge led no start just qhsusb_dload mode, (no enter in flashmode)
justinlo2000 said:
I was trying unblocking bootloader. However, when I plugged in my phone, my computer can't detect my driver downloaded.
So I tried several times unplug and plug and eventually I can't turn on my phone.
And now when I connect to my computer, there is just a qhsusb_dload drive appeared.
No idea how to fix this.....
Click to expand...
Click to collapse
Delingerb said:
I have the same problem but not same cause, No charge led no start just qhsusb_dload mode, (no enter in flashmode)
Click to expand...
Click to collapse
Even I had this problem. I searched a lot and couldn't find any proper solution.. Even RaymanFx had this problem - http://forum.xda-developers.com/showpost.php?p=49244699&postcount=1045
In the end I had to pay $222 for a new motherboard. Be sure to check out this thread too, you might find something useful - http://forum.xda-developers.com/showthread.php?t=2181451&page=5
It appears to be a fault on Sony's part and not the user.. Anway good luck and hope that you guys can recover your phones:good:
My LG E980 is bricked. I can access download mode and that is it! I am unable to boot into recovery,
and the hard reset screen simply sits there forever. My computer only recognizes my device as an "unknown usb device."
I'm unsure what can be done about this, but I feel like this is better than the infamous QHSUB icon displayed when the device cannot be recovered.
Does anyone have a remedy for this problem?? I have GOT to fix this phone and can't afford to Jtag the device, but I'm losing hope that this is possible, PLEASE help. :crying:
Have you installed the LG drivers for your pc and tried the unbrick method?
Yeah dude there's an unbrick method. If this doesn't work just sell the phone on Ebay. http://forum.xda-developers.com/showthread.php?t=2302660
There is never a time when this device cant be recovered. even the qhusb is a fairly simple fix. ill go ahead and make a sdcard boot image tonight. do you have a 32gb sdcard? (or larger) and an sdcard reader, if you have those two things i can make an unbrick.img that you flash toi the sdcard and put in the non-booting phone and it will get you to download mode/recovery mode. ill have to check out what partitions are where as i dont wish to include my efs along with it all .
twill1987 said:
My LG E980 is bricked. I can access download mode and that is it! I am unable to boot into recovery,
and the hard reset screen simply sits there forever. My computer only recognizes my device as an "unknown usb device."
I'm unsure what can be done about this, but I feel like this is better than the infamous QHSUB icon displayed when the device cannot be recovered.
Does anyone have a remedy for this problem?? I have GOT to fix this phone and can't afford to Jtag the device, but I'm losing hope that this is possible, PLEASE help. :crying:
Click to expand...
Click to collapse
Happened to me.
1. With the phone on download mode and plugged in the computer; uninstall the unknown device on your computer using device manager. The computer should try to get the drivers for your phone.
2. If it doesn't. Repeat step one and install the drivers first.
That worked for me hopefully I'll work for you.
Sent from my LG-E980 using XDA Premium 4 mobile app
Yes
riki126 said:
Have you installed the LG drivers for your pc and tried the unbrick method?
Click to expand...
Click to collapse
Yes I tried that. The drivers won't install. I even used another windows 8 computer my roommate has and switched out
the usb cables, still came back "unknown device"
shabbypenguin said:
There is never a time when this device cant be recovered. even the qhusb is a fairly simple fix. ill go ahead and make a sdcard boot image tonight. do you have a 32gb sdcard? (or larger) and an sdcard reader, if you have those two things i can make an unbrick.img that you flash toi the sdcard and put in the non-booting phone and it will get you to download mode/recovery mode. ill have to check out what partitions are where as i dont wish to include my efs along with it all .
Click to expand...
Click to collapse
I do have a 16gb sd card, but I can pick up at 32 gb sd at my local best buy. I have an Asus laptop running windows 8 and it has an SD card reader. I am a little confused (semi-noob) as to how this will work because my phone will boot up, and the led changes colors on the home button for about 4 seconds and then the light stops flashing. The phone is stuck on the LG boot screen, and there is no way out of it but to pull the battery or to reset with power button. Of course no recovery as previously mentioned. I really just want to get back to stock, but I can't manage to get both the windows 8 computers I've tried to detect the phone in download mode. Ever since I switched to the Candykat rom 4.4 the computer wasn't able to recognize the phone, even when the phone was fully functional inside the rom.
I have tried it on my dads windows 7 laptop as well with no dice. Instaled LG drivers, uninstalled LG Drivers, uninstalled device from the Device Manager. I've done everything I could think of. I previously was in a Philz touch recovery, but every rom I tried to flash wouldn't work. I tried to flash another recovery from inside it and then the device bricked like it is now. What a head ache. If you think this method would work, I am more than willing to try it, just unfamiliar with what I need to do on my end.
Okay
stulzerl said:
Happened to me.
1. With the phone on download mode and plugged in the computer; uninstall the unknown device on your computer using device manager. The computer should try to get the drivers for your phone.
2. If it doesn't. Repeat step one and install the drivers first.
That worked for me hopefully I'll work for you.
Sent from my LG-E980 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
I will give your method a shot, but I have done this a lot already. The only thing I can think of is I usually unplug the phone from the computer right after deleting the drivers and uninstalling in device manager. Maybe I should just leave the phone plugged in and see if the computer automatically downloads the drivers, but I don't think it will because I've tried to update the drivers before. It gives me an error code "10" and says the device has malfunction or stopped working This phone has been undetectable via USB since flashing the candykat 4.4 rom. Every computer I've tried (3) and every USB cable (3 again) has displayed it as an "unknown device"
twill1987 said:
I will give your method a shot, but I have done this a lot already. The only thing I can think of is I usually unplug the phone from the computer right after deleting the drivers and uninstalling in device manager. Maybe I should just leave the phone plugged in and see if the computer automatically downloads the drivers, but I don't think it will because I've tried to update the drivers before. It gives me an error code "10" and says the device has malfunction or stopped working This phone has been undetectable via USB since flashing the candykat 4.4 rom. Every computer I've tried (3) and every USB cable (3 again) has displayed it as an "unknown device"
Click to expand...
Click to collapse
I've had similar issues when i had my optimus g. I had to use a pc with xp to flasht he phone, dunno why though. You could give that a shot.
twill1987 said:
I do have a 16gb sd card, but I can pick up at 32 gb sd at my local best buy. I have an Asus laptop running windows 8 and it has an SD card reader. I am a little confused (semi-noob) as to how this will work because my phone will boot up, and the led changes colors on the home button for about 4 seconds and then the light stops flashing. The phone is stuck on the LG boot screen, and there is no way out of it but to pull the battery or to reset with power button. Of course no recovery as previously mentioned. I really just want to get back to stock, but I can't manage to get both the windows 8 computers I've tried to detect the phone in download mode. Ever since I switched to the Candykat rom 4.4 the computer wasn't able to recognize the phone, even when the phone was fully functional inside the rom.
I have tried it on my dads windows 7 laptop as well with no dice. Instaled LG drivers, uninstalled LG Drivers, uninstalled device from the Device Manager. I've done everything I could think of. I previously was in a Philz touch recovery, but every rom I tried to flash wouldn't work. I tried to flash another recovery from inside it and then the device bricked like it is now. What a head ache. If you think this method would work, I am more than willing to try it, just unfamiliar with what I need to do on my end.
Click to expand...
Click to collapse
I dont know lg's download mode, kdz, tot etc all that well. im more of a samsung guy. however qualcomm since the s4 chipset has allowed for sdcards that are properly formatted to boot the os instead of the internal emmc. here is a decent guide, just need to make teh image for this device. this will let your device boot no matter how bad it gets you are welcome to try with 16gb, the rule of thumb i know of is as big as teh emmc is use that same size or larger sdcard, however some people have had sucess withs maller, just not many that i know of. http://forum.xda-developers.com/showthread.php?t=2439367
however afaik the only way to reflash teh bootloader partitions is via kdz/download mode so perhaps the sdcard will let you get into that mode and then you can flash, so long as you keep your sdcard like that it will boot fully, but in order ot get your sdcard back you need to repair teh files on your phone .
Thanks
WeActOnImpulse said:
Yeah dude there's an unbrick method. If this doesn't work just sell the phone on Ebay. http://forum.xda-developers.com/showthread.php?t=2302660
Click to expand...
Click to collapse
I have tried this and unfortunately since the USB drivers aren't detected by the computer there is no way for me to flash back to stock.
Thanks for the information though, I appreciate it.
shabbypenguin said:
I dont know lg's download mode, kdz, tot etc all that well. im more of a samsung guy. however qualcomm since the s4 chipset has allowed for sdcards that are properly formatted to boot the os instead of the internal emmc. here is a decent guide, just need to make teh image for this device. this will let your device boot no matter how bad it gets you are welcome to try with 16gb, the rule of thumb i know of is as big as teh emmc is use that same size or larger sdcard, however some people have had sucess withs maller, just not many that i know of. http://forum.xda-developers.com/showthread.php?t=2439367
however afaik the only way to reflash teh bootloader partitions is via kdz/download mode so perhaps the sdcard will let you get into that mode and then you can flash, so long as you keep your sdcard like that it will boot fully, but in order ot get your sdcard back you need to repair teh files on your phone .
Click to expand...
Click to collapse
Wow, that sounds awesome. I followed most of that. I access download mode on the device by pressing vol up and down simultaneously and plugging in the usb cable. I am more willing to try this, and if it works I will pay you from my paypal. I guess all I need now are those files to run to the sd card. I read the tutorial you posted for the samsung and downloaded the windows disk manager. I am eager to try this method, though it is admittedly very new to me.. If you can post those files, I will follow the instructions you give and pay you a little bit of money for your help!
I am a broke college student so it won't be much, but I really appreciate your response and information on this method with the qualcomm s4.
Here is the unbrick image. follow the guide for your platform (gunna guess windows) and write this to your sdcard after backing it up. from there you need to restore your partitions by flashing them .
https://mega.co.nz/#!YB5xWQ7Y!Qcnx9UmcNn-f6skfiIFN-jd0EeYxdmrQGA1zzP5hfA0
Just wrote it to sd card
shabbypenguin said:
Here is the unbrick image. follow the guide for your platform (gunna guess windows) and write this to your sdcard after backing it up. from there you need to restore your partitions by flashing them .
https://mega.co.nz/#!YB5xWQ7Y!Qcnx9UmcNn-f6skfiIFN-jd0EeYxdmrQGA1zzP5hfA0
Click to expand...
Click to collapse
Okay so I bought the 32 gb sd card. Just wrote the .img file you sent me to the sd card.
I powered on the phone and nothing happened, I got the same LG screen where the led flashes and then stops.
I followed that guide, but am I supposed to go to download mode instead of just powering on the device?
I got a little confused by the samsung jargon lol. I just want to know after I've written the unbrick.zip to the sd card
how do I get my phone to recognize the card is there? And once I am able to do that how do I "restore my partitions by flashing them?"
I do have the factory firmware set to flash through lg flashtool, but the phone can't be detected of course due to the usb issue.
Just want to say thanks for walking me through it this far, I feel like I'm close hopefully but unsure what to do next.
twill1987 said:
Okay so I bought the 32 gb sd card. Just wrote the .img file you sent me to the sd card.
I powered on the phone and nothing happened, I got the same LG screen where the led flashes and then stops.
I followed that guide, but am I supposed to go to download mode instead of just powering on the device?
I got a little confused by the samsung jargon lol. I just want to know after I've written the unbrick.zip to the sd card
how do I get my phone to recognize the card is there? And once I am able to do that how do I "restore my partitions by flashing them?"
I do have the factory firmware set to flash through lg flashtool, but the phone can't be detected of course due to the usb issue.
Just want to say thanks for walking me through it this far, I feel like I'm close hopefully but unsure what to do next.
Click to expand...
Click to collapse
you wrote the image to the sdcard? i wonder if its because you still have the low level bootloaders that it may not be booting from the sdcard, normally this is done to fix qhusb errored devices. as for restoring the partitions all you would need to do is one its booted up push the unbrick image to the phone and use rooted adb shell to write it back onto your phone.
Possible hope??
shabbypenguin said:
you wrote the image to the sdcard? i wonder if its because you still have the low level bootloaders that it may not be booting from the sdcard, normally this is done to fix qhusb errored devices. as for restoring the partitions all you would need to do is one its booted up push the unbrick image to the phone and use rooted adb shell to write it back onto your phone.
Click to expand...
Click to collapse
I meant I used the windows tool to write the debrick.img to the sd card. But no dice, the device isn't recognised.
However! I installed a driver clean up tool and now if I plug in the device it is recognized as Android Original ADB Interface.
The LG Flashtools even says the port is ready! But I get the error code "10" "device cannot start, A request for the USB device descriptor failed."
So now I am stuck on that instead lol. This just sucks.
that sucks about the sdcard, it must be because you arent "truly" bricked. sorry i thought it would help ya :/.
What is the driver repair tool you used? I know this thread is old but I'm having the same problem. I was trying to root my E980 and now my computer wont recognize my device. The phone works perfect, its just when I plug it in to the computer it isnt recognized. How can I fix this?
+1
Just wondering if anyone's come across a solution to this besides a sledge hammer... been having the same "Code 10: Device failed to start" when in Download Mode, though Windows finds a driver fine when the phone is stuck on the LG screen... doesn't help much, though, 'cause it won't receive adb commands. I manually installed the LG USB Composite Device driver, which added a modem and a COM port, both of which Windows recognized to be active, but the LG FlashTool USB Viewer showed no open pipes. I'm a relative noob, so please feel free to point out the obvious, like an alternative to adb that the phone can always receive or a way to brick it the rest of the way so the MicroSD trick will work.
I came across this problem like the OP and just wanna let everyone know that you have to use computer with USB 2.0 port then the driver issue would be fixed.
Hello everyone.
I need your help.
My Device: LG G3 D855 32GB
The device does not turn on, the only thing that appears is because when I connect the device to a PC, I see a driver installed:
RELINK HS-USB QDLoader 9008
I read guides on site here, and I'm trying to order
I downloaded the software BoardDiag 2.9
I downloaded the files to the appropriate TOT
I extracted the files by instructors on site.
I opened the program and I followed the guide and it seems to me an error
Download mode is enabled Mode,
I quickly disconnects from the computer and reconnect the computer and then the moment I am unable to do a test and the results are:
AP CHECK START = PASS
EMMC TEST START
FAILED TO OPEN PARTITION FROM EMMC
TEST ABORTED !!
I tried a lot of tutorials but I can not, it always seems the device is in Download Mode
What can I do more?
Please your help,
Eliran
If you go that way, you will need bunch of other stuff. Here is the link
http://open-freax.fr/guide-unbrick-your-lg-g3/
It is a good thing that your PC recognises phone like that.
But first be sure that You can not enter download mode or recovery or even fastboot.
And please say what did you do to make it like that? Wrong flash?
If you CAN enter download mode than you can flash kdz or tot files from there. Easiest way is to use LGUP but you must be careful if you want to try.
The phone fell
Navuhodonosor said:
If you go that way, you will need bunch of other stuff. Here is the link
It is a good thing that your PC recognises phone like that.
But first be sure that You can not enter download mode or recovery or even fastboot.
And please say what did you do to make it like that? Wrong flash?
If you CAN enter download mode than you can flash kdz or tot files from there. Easiest way is to use LGUP but you must be careful if you want to try.
Click to expand...
Click to collapse
Thanks for the comment
The phone fell into the vehicle.
I know the phone is always in Download Mode
The software does not let me do anything and making phone download mode
I did not try to install KDZ.
And I can not open a setup KDZ because the device does not rise and there is no open port.
I only have the port I did above.
Thanks for the help, I worked in the guide and I could not ...
Navuhodonosor said:
If you go that way, you will need bunch of other stuff. Here is the link
It is a good thing that your PC recognises phone like that.
But first be sure that You can not enter download mode or recovery or even fastboot.
And please say what did you do to make it like that? Wrong flash?
If you CAN enter download mode than you can flash kdz or tot files from there. Easiest way is to use LGUP but you must be careful if you want to try.
Click to expand...
Click to collapse
Thanks for the help, I worked in the guide and I could not ...
I went through all the steps I found at:
Now, let’s get the party started
I set up the software the guide and I got an error:
FAIL on the EMMC test
I changed the parameter Read / Write »to« Erase
And again I got the error:
FAIL on the EMMC test
Then I try again, click Start, open a window and write in English and Chinese
Device DLOAD mode
device was not found in dload trying flash peogrammer
I click OK, the window closes and then when I press Start again, the window reappears.
Only when I disconnect the USB cable from the computer and the author briefly again then I’m able to do the test, but he failed.
FAIL on the EMMC test
The device always is in Download Mode and appears port:
RELINK HS-USB QDLoader 9008
My component can not be right at all and it always is in Download Mode?
I did not do short the guide, because the computer also detected me.
It has always seemed stuck in a download mode.
There is another option? Short elsewhere as will enable progress?
Thank you very much for your help,
Eliran
I need help please. What can i do
zarfati66 said:
Thanks for the help, I worked in the guide and I could not ...
I went through all the steps I found at:
Now, let’s get the party started
I set up the software the guide and I got an error:
FAIL on the EMMC test
I changed the parameter Read / Write »to« Erase
And again I got the error:
FAIL on the EMMC test
Then I try again, click Start, open a window and write in English and Chinese
Device DLOAD mode
device was not found in dload trying flash peogrammer
I click OK, the window closes and then when I press Start again, the window reappears.
Only when I disconnect the USB cable from the computer and the author briefly again then I’m able to do the test, but he failed.
FAIL on the EMMC test
The device always is in Download Mode and appears port:
RELINK HS-USB QDLoader 9008
My component can not be right at all and it always is in Download Mode?
I did not do short the guide, because the computer also detected me.
It has always seemed stuck in a download mode.
There is another option? Short elsewhere as will enable progress?
Thank you very much for your help,
Eliran
Click to expand...
Click to collapse
I need help please. What can i do
The phone woke for a moment ...
zarfati66 said:
I need help please. What can i do
Click to expand...
Click to collapse
Hello everyone
Today I tried again to connect the device to your computer, the screen comes on suddenly.
And see the state of battery with a question mark inside a yellow triangle.
I did not realize also saw installed driver
LGE AndroidNet USB Serial Port
I tried to re-install.
Now again became a black screen and the next thing happens:
When the device without a battery connected to a computer costing me
RELINK HS-USB QDLoader 9008
When I'm with a battery, it registers an unknown device.
When the device without a battery test again tried to do this EMMC component fails.
help please
Eliran
relink hs-USB Qdloader 9008
ZARFATI6 said:
Hello everyone
Today I tried again to connect the device to your computer, the screen comes on suddenly.
And see the state of battery with a question mark inside a yellow triangle.
I did not realize also saw installed driver
LGE AndroidNet USB Serial Port
I tried to re-install.
Now again became a black screen and the next thing happens:
When the device without a battery connected to a computer costing me
RELINK HS-USB QDLoader 9008
When I'm with a battery, it registers an unknown device.
When the device without a battery test again tried to do this EMMC component fails.
help please
Eliran
Click to expand...
Click to collapse
I am exactly in the same situation. Have you found any solution so far???? My phone suddenly stopped working and didn't boot up at all first and then I used the LG Flashtool to install original TOT file and all went well. I forgot to close LG Flashtool and it started flashing again. LG Flash tool restarts the phone at about 80% and then it failed at that point and since then I am having this issue.................
Any solution???????
apur32 said:
I am exactly in the same situation. Have you found any solution so far???? My phone suddenly stopped working and didn't boot up at all first and then I used the LG Flashtool to install original TOT file and all went well. I forgot to close LG Flashtool and it started flashing again. LG Flash tool restarts the phone at about 80% and then it failed at that point and since then I am having this issue.................
Any solution???????
Click to expand...
Click to collapse
Same situation too, solutions yet?
Hey I have the same problem .
If any of you found the solution please post it here or pm me, I am stuck
Hello guys,
I'm using my 3T carefully as a media device just at home. But suddenly I couldn't control my system anymore. I could swipe and open settings, but couldn't turn on WiFi or start any app. So I restarted my phone but it never booted. Screen is completely black and even charging leds doesn't work anymore. I can't access TWRP recovery. I used the button combinations ... Nothing! But when I connect my phone to my computer windows plays the typical sound like when you plug in an USB stick. Windows sayed once that the connected device is buggy and cannot be detected. Nothing more. When I reconnect no more message or pop up again.
Has anyone any idea? Thanks a lot!
slev!n said:
Hello guys,
Screen unit is completely dead. It even doesn't show a charging led anymore. I can't access TWRP recovery. I used the button combinations ... Nothing! But when I connect to the computer windows registers my phone by playing the 'connected sound'. But nothing more. Has anyone any idea or know where I can discuss my issue? Thanks a lot!
Click to expand...
Click to collapse
That's weird. Sounds like your screen (if not more parts) died. Hardware issue? Water damage? Might be better to contact a repair center since if you can't even access recovery I doubt the problem is related to LOS. Never happened on my 3T over the 4 years I've had it, though it's had its fair share of damage.
knpk13 said:
That's weird. Sounds like your screen (if not more parts) died. Hardware issue? Water damage? Might be better to contact a repair center since if you can't even access recovery I doubt the problem is related to LOS. Never happened on my 3T over the 4 years I've had it, though it's had its fair share of damage.
Click to expand...
Click to collapse
But before my restart I could use the screen it just looks like something in the system doesn't work: could type on apps and settings, it just doesn't open or pop back. And the charging led is not part of the screen unit as I know.... If I could take out the battery I would do it. It often works in other phones. But I don't have tools here for my 3T. :/
knpk13 said:
That's weird. Sounds like your screen (if not more parts) died. Hardware issue? Water damage? Might be better to contact a repair center since if you can't even access recovery I doubt the problem is related to LOS. Never happened on my 3T over the 4 years I've had it, though it's had its fair share of damage.
Click to expand...
Click to collapse
slev!n said:
But before my restart I could use the screen it just looks like something in the system doesn't work: could type on apps and settings, it just doesn't open or pop back. And the charging led is not part of the screen unit as I know.... If I could take out the battery I would do it. It often works in other phones. But I don't have tools here for my 3T. :/
Click to expand...
Click to collapse
slev!n said:
Hello guys,
I've got an issue and don't know if it belongs to the build or not. I'm on the last build with my 3T and today after charging my phone I couldn't turn on WiFi or start any app. It just didn't open. So I restated my phone but it never booted. Screen unit is completely dead. It even doesn't show a charging led anymore. I can't access TWRP recovery. I used the button combinations ... Nothing! But when I connect to the computer windows registers my phone by playing the 'connected sound'. But nothing more. Has anyone any idea or know where I can discuss my issue? Thanks a lot!
Click to expand...
Click to collapse
Sounds to me like an hardware error involving (but not necessarily limited to) emmc access. That would explain, why the parts still in ram (like homescreen) were still working but apps won't start anymore, as well as the blank screen on device startup (even the logo needs emmc access to read the logo partition).
Try unbricking (I'm afraid your pc won't find the device, if my guess is correct), if that fails: rma or repair center.
slev!n said:
Has anyone any idea or know where I can discuss my issue? Thanks a lot!
Click to expand...
Click to collapse
here
You need to be more spesific about the connected sounds, does it shows up on device manager or else, in detail (with SS/photos etc to prevent misjudge)
150208 said:
here
You need to be more spesific about the connected sounds, does it shows up on device manager or else, in detail (with SS/photos etc to prevent misjudge)
Click to expand...
Click to collapse
Thanks, I'll create a post there. Just one more post here:
I used this phone just carefully at home as a media device. So this brick came totally out of nowhere. When I connect my bricked 3T now to my computer it makes the typical sound like when you plug in an USB stick. Windows sayed once that the connected device is buggy and cannot be detected. Nothing more. When I reconnect no more pop up again.
slev!n said:
I'll create a post there.
Click to expand...
Click to collapse
When you've created that post ask the moderators to move this complete conversation from this thread to the newly created on in the help forum, please. This helps to keep this thread readable and searcheble.
For your trouble: if you can't boot rom, recovery nor fastboot mode, it doesn't make sense to debug the usb connection: what should the pc connect to if none of the three is bootable? There is just nothing up to connect to. That's why I recommended unbrick tool - if that fails rma or go to a repair center.
Hello guys,
I'm using my 3T carefully as a media device just at home. But suddenly I couldn't control my system anymore. I could swipe and open settings, but couldn't turn on WiFi or start any app. So I restarted my phone but it never booted. Screen is completely black and even charging leds doesn't work anymore. I can't access TWRP recovery. I used the button combinations ... Nothing! But when I connect my phone to my computer windows plays the typical sound like when you plug in an USB stick. Windows sayed once that the connected device is buggy and cannot be detected. Nothing more. When I reconnect no more message or pop up again.
Has anyone any idea? Thanks a lot!
Post SS of the device manager after connecting the phone to the PC
150208 said:
Post SS of the device manager after connecting the phone to the PC
Click to expand...
Click to collapse
It doesn't make sense to debug the pc conmection: if neither recovery, fastboot mode nor rom is bootable, there is nothing up and running the pc can connect to (maybe unbrick tool can still access the msm hardware directly, but that's not sure - confirmation is still missing from @slev!n). I'm writing this the second time.
If none of recovery, fastboot mode nor rom is bootable, the last resource before rma or repair center is unbrick tool. I'm writing this the third time!
@slev!n: please ask the moderators to move the existing conversation to thos from the los16 thread here. If all postings have moved, ask the moderators to move this thread from op3/help to op3t/help.
@nvertigo67 I wanted to do so and was searching how to contact moderators but couldn't find it in my XDA app. Maybe someone can give me a hint? I'm kind of new on xda... Thanks!
@150208 And as I wrote: it's not possible to get any kind of message on windows anymore. Just the sound appears when I connect and disconnect.
@nvertigo67 I was also following your advice to use the unbrick tool. I followed the steps on oneplus forum:
https://forums.oneplus.com/threads/guide-oneplus-3-3t-unbrick.531047/
When it comes to the integrity check windows doesn't accept "TESTSIGNING ON". And so windows doesn't recognise my phone in the device manager for the next steps.
And I guess RMA or repair centres are super expensive. I don't know if it's worth it? I thought about buying a device with a broken screen on eBay and try to change the motherboard...
Log in with a web browser locate each posting of the comversation. For each posting in question use the little triangle icon at the botom on the left side, report each posting, set non-urgent and pit the link of this thread together with something like "Please move this posting to the linked thread, thanx in advance".
For disabling driver signature enforcement try method 2. from this post: http://maxedtech.com/about-testmode/
Most of tbe time xda postings are more reliable and more current then the Oneplus forums: https://forum.xda-developers.com/oneplus-3/how-to/op3-collection-unbrick-tools-t3896722, https://forum.xda-developers.com/oneplus-3/how-to/op3-collection-unbrick-tools-t3896722
slev!n said:
[MENTION=4405529]i thought about buying a device with a broken screen on eBay and try to change the motherboard...
Click to expand...
Click to collapse
If you already have a thought why do you keep asked here though? If you want another possible solution, at least put an effort to provide the information needed when asked by the one who tried to help you
I'm not into a guessing games, so i'm out
nvertigo67 said:
It doesn't make sense to debug the pc conmection: if neither recovery, fastboot mode nor rom is bootable, there is nothing up and running the pc can connect to (maybe unbrick tool can still access the msm hardware directly, but that's not sure - confirmation is still missing from @slev!n). I'm writing this the second time.
If none of recovery, fastboot mode nor rom is bootable, the last resource before rma or repair center is unbrick tool. I'm writing this the third time!
Click to expand...
Click to collapse
There are 2 possible reason when the phone is not detected by the computer, driver or hw problem.
To know it i need to look at the device manager status
If it's hw problem, i'll try not to jump on MB conclussion yet, since there are still another possible reason
When talking about MSM, you need to make sure it's available first on the device manager
Otherwise, it's a waste of data for downloading the tool in these human malware days
Oh yes, the msm guide is quite lag behind. You don't need to boot into test mode anymore with the current driver for qualcomm
I flashed a lot qualcomm devices with w10 without the need to boot into test mode
150208 said:
There are 2 possible reason when the phone is not detected by the computer, driver or hw problem.
To know it i need to look at the device manager status
Click to expand...
Click to collapse
True, if only "win is not detecting the device" is known. Since we know much more (neither rom, recovery nor fastboot mode are bootable), the debugging of the usb driver doesn't make sense. The msm tool uses it's own drivers to detect the hardware BEFORE one of the three is booted. If the msm tool has unbricked the device and booting recovery, rom and/or fastboot, you can start debugging the "nprmal" qc usb drivers, if still necessary.
For the costs of rma: maybe it's expensive - maybe oneplus will be obliging... Since you don't relay on the device as your daily driver, you can ask for an estimate of costs - so you can decide if it's worth the costs.
nvertigo67 said:
True, if only "win is not detecting the device" is known. Since we know much more (neither rom, recovery nor fastboot mode are bootable), the debugging of the usb driver doesn't make sense. The msm tool uses it's own drivers to detect the hardware BEFORE one of the three is booted. If the msm tool has unbricked the device and booting recovery, rom and/or fastboot, you can start debugging the "nprmal" qc usb drivers, if still necessary.
Click to expand...
Click to collapse
Wait, I fail to see your explanation in line with mine. I want to start debug it on the windows side, but you seems to see it on the phone side.
Do you realize there are cases where everything is black/nothing responding but it's still detected by computer? That when emmc is corrupt, but repairable if you format it.
150208 said:
Do you realize there are cases where everything is black/nothing responding but it's still detected by computer? That when emmc is corrupt, but repairable if you format it.
Click to expand...
Click to collapse
If neither fastboot mode nor recovery is bootable, you need the msm interface to refprmat somethimg on emmc. In other words: if there's no recovery nor fastboot, you can't utilize adb or fastboot to reformat or to fix the partition table. You need something to connect to to do the fixing, but without recovery or fastboot, there is nothing adb or fastboot can conmect to, no matter of the driver status on the pc/win side. Once this is fixed (at least fastboot mode is up again) you can utilize the "normal" usb connection again.
What do you want to do with the usb connection, if neither fastboot mode nor recovery is up amd running? What is your suggested next step, if the device is recognized? What should the pc recognize if neither fastboot nor adb os an option? Which command or procedure will fix the emmc?
nvertigo67 said:
If neither fastboot mode nor recovery is bootable, you need the msm interface to refprmat somethimg on emmc.
Click to expand...
Click to collapse
Yes, there are other tools but i'm not gonna bother since it's paid
nvertigo67 said:
In other words: if there's no recovery nor fastboot, you can't utilize adb or fastboot to reformat or to fix the partition table. You need something to connect to to do the fixing, but without recovery or fastboot, there is nothing adb or fastboot can conmect to, no matter of the driver status on the pc/win side.
Click to expand...
Click to collapse
This is the part where you're incorrect. There are 4 status when a device plugged into the pc.
1. detected and driver is loaded
2. detected and driver isn't loaded
3. detected but not recognized
4. no sign at all
1 and 2 is sw problem, 3 and 4 is hw problem
In order for MSM to do it's job, you need to have either problem no 1 or 2 with qualcomm qloader 9008 driver already or later detected in devmanager
So it's important to know the driver status
OP states there was sounds coming then nothing, which mean it's either 2 or 3, more like 3 but again i repeating myself i don't like guessing games
I don't understand the part why you're explaining/asking about fastboot recovery or etc, his phone is on dead state, nothing-literally-no sign of life unless he plug it to the pc and then it making sounds for the first time,
Why do you even bother thinking about it?
nvertigo67 said:
Which command or procedure will fix the emmc?
Click to expand...
Click to collapse
No procedure will fixed his phone since there are no enough information
I think your other question should be already answered. If else, i don't know what to say anymore.
150208 said:
nvertigo67 said:
In other words: if there's no recovery nor fastboot, you can't utilize adb or fastboot to reformat or to fix the partition table. You need something to connect to to do the fixing, but without recovery or fastboot, there is nothing adb or fastboot can conmect to, no matter of the driver status on the pc/win side.
Click to expand...
Click to collapse
This is the part where you're incorrect.
Click to expand...
Click to collapse
If so, please explain how you can format a partition or fix the partition table if neither fastboot mode nor recovery (or a rooted system for that matter) is bootable.
@slev!n: please give a screenshot of the device manager to @150208. I'm too curious to learn how to fix a broken emmc without recovery nor fastboot mode.
Thank you so far!
I dont want to bother someone. Just thinking about further options thats why I wrote my thought about replacing the motherboard down.
I 'm in test mode now and I did this:
"Step 4 :- Press the power button for 40 seconds to turn off the phone.
Step 5 :- Press only volume up button for a few seconds and while keeping it pressed,connect your phone to PC.Keep volume up pressed till your device shows in device manager as [Unknown Device,QHUSB_BULK (under Unknown Devices) or Qualcomm HS USB (under COMs and Ports)]."
But no device is listet in my device manager. But in msmtool my phone is connected. Does it mean I cann't continue with this tool somehow?
slev!n said:
But no device is listet in my device manager. But in msmtool my phone is connected. Does it mean I cann't continue with this tool somehow?
Click to expand...
Click to collapse
The pic is from msm tool, not the device manager. No unknown device in device manager?