Currently it can run download mode and recovery mode. After the 2nd splash screen it goes to black. To go into these modes, I must remove the battery to shut it down then restart it.
I have tried many things to fix it:
Recovery > Restore Factory Default failed due to error
Odin > Install custom recovery > Restore failed due to error
Odin > flash firmware failed due to:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I747UCDLK3_I747ATTDLK3_I747UCDLK3_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I have no idea what to do and I Do not have an SD card. What are my options?
Thank you!
NOTE: I HAVE TRIED FLASHING AND RESETTING TO FACTORY DEFAULT. Last guy who tried to answer did not read my question, assumed from the title. Thanks
Member, please read forum rules before posting
You may ask your question only once, if no response you may bump thread once after 24 hours
Please return to the other thread you made and work out your issue with the bootloader
Thread closed
Related
I flashed to Stock with ODIN and it went successful then I downloaded the updated firmware version to flash through ODIN because it wouldn't update through KIES or from itself and half way through, it failed and now it says "Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again."
It doesn't work through Kies, it just keeps trying to connect but no connection so I tried to flashing back to the old firmware through ODIN again and everything works successful until this part
"<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> T989UVKL1_HOME_SGH-T989user_CL799405_REV00.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> boot.img
<ID:0/003> NAND Write Start!!
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
<ID:0/003> Added!!
<ID:0/003> Removed!!
<ID:0/003> Added!!"
I've tried everything but switch to a different computer to try it on, what do you guys think I should do?
How interesting, after hours and hours of stress, all I did was flash stock recovery through ODIN and now it rebooted fine
Hello all,
I have a Samsung Note 4 from sprint. I tried rooting my phone earlier and then it just began to restart over and over. I researched and found some solutions which none have worked thus far. Maybe someone can help me out. Current things that I have tried.
1. Rebooted the device and did a factory reset and clearing the cache hoping that would fix the problem. The phone just continued to restart.
2. Next I downloaded the original firmware for my device that I found. The name was GalaxyNote4/SM-N910P/5.0.1/N910PVPU1BOB7_N910PSPT1BOB7_SPR.zip I tried using this and got the Fail! using Odin3 V 3.10
Here is what the Log says:
ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N910PVPU1BOB7_N910PSPT1BOB7_N910PVPU1BOB7_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1005)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl1.mbn
<ID:0/003> rpm.mbn
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Any help would be much appreciated, thank you for your time.
What firmware/rom did you start with? Sounds like you were on something beyond OB7, like OE1, OF5 or OG5 none of which will allow downgrading to OB7.
Sent from my SM-N910P using Tapatalk
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G925IDVU2DOI2_G925IXSA2DOI2_G925IDVU2DOI2_HOME.tar .md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1005)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I keep getting this error message when i use odin to flash any firmware and the phone wont boot up. What should i do?
There are multiple things that can cause it. First try different cables and usb ports. Many times I got stuck like that because odin just didn't like the port I was using. If all else fails you will have to use the Samsung Smart Switch pc app to do an emergency recovery. To find your SN easily go into Download mode by pressing Vol Down + Home + Power then don't hit Vol up instead hit the Home button and it will show your IMEI an SN. then insert your SN into the emergency recovery in Smart Switch.
WARNING!!!!! you will lose all data including your internal sd card. Warning!!!!!
You could try searching around a little here on xda as well. I have read a few posts where people were able to fix it with a specific firmware file. and that was with the FRP lock problem.
randy954 said:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G925IDVU2DOI2_G925IXSA2DOI2_G925IDVU2DOI2_HOME.tar .md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1005)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I keep getting this error message when i use odin to flash any firmware and the phone wont boot up. What should i do?
Click to expand...
Click to collapse
you put the G925i firmware on G925T?
Rachy01 said:
you put the G925i firmware on G925T?
Click to expand...
Click to collapse
Bingo!
Give the man a cigar. :sly:
Pp.
Hi guys my step son has proper messed up his phone he's somehow tripped knox and is stuck in a bootloop. I cannot seem to find a current recovery from brick solution for the latest firmwares. The only guide I can find seems to be before knox was implemented I've been looking round and tried one or two guides with no success. I'm really stuck here and am pleading for any help I can get.
Thank you for your help
tell some detailts ..problem is bootloop ? tried Flashing official firm thru odin ?!
Iskander_mal said:
tell some detailts ..problem is bootloop ? tried Flashing official firm thru odin ?!
Click to expand...
Click to collapse
Yes I've tried flashing the official firmware through Odin and I get a massive fail h t t p ://imageshack.com/a/img924/4719/Ou2z5N.jpg
That's what is displayed on the screen
Here's the Odin log
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7100XXUFNE1_N7100BTUFNE1_N7100XXUFND3_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1005)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> system.img
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Thank you ever so much for taking the time to reply
Update!! Please delete this tread. problem solved. im an idiot sorry.
Hello everyone! So i have softbricked my SM-T210 (without the R). I had it running perfectly with CWM recovery with AICP Nougat. I'm not sure what i broke but it won't boot into Recovery or System. I tried using Odin to reflash the custom recovery which Odin marked as successful (first CWM then when that wouldn't boot i did TWRP). After that I tracked down the stock rom and attempted to Odin flash that which came back as a fail.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> T210XXBOA3_T210BTUBOA2_Home.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> PBL.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
Productive assistance would be greatly appreciated! thanks for reading.