Develop Bugs

[Q] Cannot install clockwork mod

Used the one click el29 root and then used e4gauto, but option c, L just gets me an error:
failed to copy 'copy2sd/000root/superuser.apk -> /sdcard/000root/superuser.apk'
not a directory.
Flashed back to stock el29 and started over, same result. Any idea on how to get clockwork mod flashed onto this phone?

I'd suggest using the Odin method from sfhub (again). Download the file then use something like 7zip or Winzip to extract the actual OneClick.exe file to a folder of your choice. Then run if run it from there. Make sure you are able to boot a few times and all works (I usually use the no data file to preserve my settings). Then head over to the e4gauto etc. One thing I have found (and MANY others too!) is to make sure you use a very good USB cable. I have had SO many problems with roots/etc. because of ****ty cables! It is incredible the amount of time I've wasted when all I needed was to just get a new good USB cable! For printers, phones, cameras and other devices. Good luck

Cannot install clockworkmod
I have tried the odin method several times, both nodata and the one that cleared my settings. I have no problem with rooting. I even urooted back to stock with a factory reset and started over.
I have been using the Samsung usb cable that came with the phone. It has never failed me in the past.
It seems as though eg4auto is trying to access a directory that doesn't exist. On my phone superuser.apk is located in the system\apps directory. I think Eg4auto is looking for 000root\superuser.apk.

bgbuffalo said:
Used the one click el29 root and then used e4gauto, but option c, L just gets me an error:
failed to copy 'copy2sd/000root/superuser.apk -> /sdcard/000root/superuser.apk'
not a directory.
Flashed back to stock el29 and started over, same result. Any idea on how to get clockwork mod flashed onto this phone?
Click to expand...
Click to collapse
It appears you may have missed the pre-requisite that usb storage mode should be disable (ie the android guy should be green)

Cannot install clockworkmod
I thought of that, but you cannot get into usb storage mode when you have USB Debugging ticked. Or am I missing something here?

bgbuffalo said:
I thought of that, but you cannot get into usb storage mode when you have USB Debugging ticked. Or am I missing something here?
Click to expand...
Click to collapse
You can in fact connect to USB storage with debugging enabled.
You must have debugging enabled and USB storage must not be enabled.

Then I must be a complete idiot. if I turn on debugging mode and go to usb storage, it tells me to turn off debugging mode. If I go to usb storage first and get the green man, then go back to tick debugging mode it will not allow it until I disconnect cable.

WoW just WoW. think hard, you can do it, I have faith in ya.

How about a hint?

Well, I was messing around and hit "stop adb". Now I get a "more than one device or emulator". Reflashed el29 with odin one click, but still get the error message.

Hint, you're in the wrong mode (USB). You might want to reread the directions.

cannot install clockworldmod
Ok. Here's what I do. First make sure debugging mode is on. Then connect usb cable. I slide down the notification bar and click on connected to usb which brings me to the screen with the green guy.
At that point I run the program and get an error. What am I missing?

bgbuffalo said:
Ok. Here's what I do. First make sure debugging mode is on. Then connect usb cable. I slide down the notification bar and click on connected to usb which brings me to the screen with the green guy.
At that point I run the program and get an error. What am I missing?
Click to expand...
Click to collapse
Sounds like a bad download. Redownload try it over. report back. I actually have not used this method. I rooted with bubbys **** a long time ago and have never had to go back to stock. But I will try to help ya out.

bgbuffalo said:
Ok. Here's what I do. First make sure debugging mode is on. Then connect usb cable. I slide down the notification bar and click on connected to usb which brings me to the screen with the green guy.
At that point I run the program and get an error. What am I missing?
Click to expand...
Click to collapse
What error are you getting now? Is it the same as before or a different error?
All that part of the script is doing is using adb to push some files to your phone in the /sdcard/000root directory.
If you do "adb shell" and "cd /scard", then type "ls -l", what do you see?
If it has no files or subdirectories, then your /sdcard partition is not visible for some reason.

sfhub said:
What error are you getting now? Is it the same as before or a different error?
All that part of the script is doing is using adb to push some files to your phone in the /sdcard/000root directory.
If you do "adb shell" and "cd /scard", then type "ls -l", what do you see?
If it has no files or subdirectories, then your /sdcard partition is not visible for some reason.
Click to expand...
Click to collapse
Listen to Sfhub. He will not steer ya wrong.

Bear with me here. Do I do those commands on the phone using connectbot in local mode? If so, the adb shell command returns "adb: not found". Or do I need the developer toolkit?

When you plug in the phone as long as usb debugging is on, you shouldn't be clicking on the green android, that would enable usb mode. The files will be pushed thru adb you should not have be clicking anywhere on the green android guy.

bgbuffalo said:
Bear with me here. Do I do those commands on the phone using connectbot in local mode? If so, the adb shell command returns "adb: not found". Or do I need the developer toolkit?
Click to expand...
Click to collapse
Does your USB storage mode look like this:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
It should NOT be orange. It should look exactly like the picture above.
If you need to run "adb shell", use Option D, then choose adb shell. If your auto root package doesn't have "adb shell" as an option, get the latest one.
Then type:
Code:
cd /sdcard
ls -l

Yes it looks exactly as pictured. That's why I was sure it wasn't that i had the usb mode wrong. I will try your other suggestion and get back to you.

I got what looks like a directory of the sd card.
Now when I run eg4tauto I am getting daemon not running, adb server didn't ack

[Q] Usb Malfunctioned?

Yesterday I plugged my phone with usb to the pc but it didn't recognize it, When I tried with another cable , One of the devices you connected was not recognized" this message popped, the phone was recognized day before yesterday and before that but suddenly it's unrecognized by the system. How do I fix this? I tried plugging my phone to my friend's pc but still it gives the same error,

Jexbox said:
Yesterday I plugged my phone with usb to the pc but it didn't recognize it, When I tried with another cable , One of the devices you connected was not recognized" this message popped, the phone was recognized day before yesterday and before that but suddenly it's unrecognized by the system. How do I fix this? I tried plugging my phone to my friend's pc but still it gives the same error,
Click to expand...
Click to collapse
Do you have HTC sync installed? Or have you ever had the right drivers installed on this PC? If so you can try go into device manager on windows, select the malfunction device and manually change its driver to the HTC drivers and see if that works
Sent from my HTC Desire S using Tapatalk

heavy_metal_man said:
Do you have HTC sync installed? Or have you ever had the right drivers installed on this PC? If so you can try go into device manager on windows, select the malfunction device and manually change its driver to the HTC drivers and see if that works
Sent from my HTC Desire S using Tapatalk
Click to expand...
Click to collapse
Yea It used to detect my phone earlier but suddenly it has stopped, with the stock usb cable nothing gets detected, and when I try with others it pops the message that it is unrecognized.

Jexbox said:
Yea It used to detect my phone earlier but suddenly it has stopped, with the stock usb cable nothing gets detected, and when I try with others it pops the message that it is unrecognized.
Click to expand...
Click to collapse
Have you tried
Code:
adb devices
?
What does it say?

mcgi5sr2 said:
Have you tried
Code:
adb devices
?
What does it say?
Click to expand...
Click to collapse
It returns nothing
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
even tried to run fastboot in bootloader, It doesn't detect the phone which it used to detect previously, the phone is still in warranty but I can't give it because I can't even restore my stock backup as I won't be able to flash the stock kernel again is there any other way to return to stock?

Jexbox said:
It returns nothing
even tried to run fastboot in bootloader, It doesn't detect the phone which it used to detect previously, the phone is still in warranty but I can't give it because I can't even restore my stock backup as I won't be able to flash the stock kernel again is there any other way to return to stock?
Click to expand...
Click to collapse
OK panic not.
First see if you can test it on another computer. The HOV doesn't agree with USB3.0 so if you have any usb ports that aren't that, then try it there. Is the phone S-OFF? If so you could try and flash by putting the rom.zips on your sd-card then rebooting into recovery.
Also can you check adb with the other cables as well?

mcgi5sr2 said:
OK panic not.
First see if you can test it on another computer. The HOV doesn't agree with USB3.0 so if you have any usb ports that aren't that, then try it there. Is the phone S-OFF? If so you could try and flash by putting the rom.zips on your sd-card then rebooting into recovery.
Also can you check adb with the other cables as well?
Click to expand...
Click to collapse
I tested it on other 2 computers with 3 different cables, Adb doesn't detect my phone, The phone is S-ON, I tested it on all ports still no recognition, The phone charges through the USB but it is not recognized, I also looked at the HTC Dumlock method as I have TWRP installed, should I try that ?

Jexbox said:
I tested it on other 2 computers with 3 different cables, Adb doesn't detect my phone, The phone is S-ON, I tested it on all ports still no recognition, The phone charges through the USB but it is not recognized, I also looked at the HTC Dumlock method as I have TWRP installed, should I try that ?
Click to expand...
Click to collapse
That is very strange indeed, if it charges then it should be recognised by ADB. Are you sure your running adb from a folder it works from, are the drivers installed on the computers you tested it on?
I don't know anything about the Dumlock method so really can't advise

mcgi5sr2 said:
That is very strange indeed, if it charges then it should be recognised by ADB. Are you sure your running adb from a folder it works from, are the drivers installed on the computers you tested it on?
I don't know anything about the Dumlock method so really can't advise
Click to expand...
Click to collapse
Yea, it is strange, I was running adb for a long time on my pc and it was working and this thing has just started recently, I've read many similar posts with this strange problem but none of them give an solution to it.

Jexbox said:
Yea, it is strange, I was running adb for a long time on my pc and it was working and this thing has just started recently, I've read many similar posts with this strange problem but none of them give an solution to it.
Click to expand...
Click to collapse
Could you try it without your SD card in?

mcgi5sr2 said:
Could you try it without your SD card in?
Click to expand...
Click to collapse
Tried. still not working

Jexbox said:
Tried. still not working
Click to expand...
Click to collapse
It might be worth trying with different usb cables. If this wont help the hOV micro usb socket could be physically broken. :\

kvestas said:
It might be worth trying with different usb cables. If this wont help the hOV micro usb socket could be physically broken. :\
Click to expand...
Click to collapse
Can't tell cause the phone gets charged but it's not detected, tried at least 5-6 wires on different computers still the same

Ok another idea you could try is flashing a different rom. I am plucking at straws here though, as all our 4.2.2 roms are currently based on 1ceb0xs one anyway. Have you tried re-installing the rom from recovery?

mcgi5sr2 said:
Ok another idea you could try is flashing a different rom. I am plucking at straws here though, as all our 4.2.2 roms are currently based on 1ceb0xs one anyway. Have you tried re-installing the rom from recovery?
Click to expand...
Click to collapse
Will give it a try and report back.

No OS, OTG not recognized. Am I bricked?

Accidental full wipe of my Nexus 7 has left me with a no OS paper weight.
Fastboot indicates it's locked but I can boot into TWRP, but can't get it to be recognized by any PC and it won't recognize my OTG-USB (which has been recognized by others).
Any ideas as to how to get her up and running would be greatly appreciated.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

Did you mount the OTG usb in TWRP or just looked for it to auto detect?
Btw, this belongs in the Q & A section, so ask a mod to move it

I am unable to select/check mount the OTG while in TWRP. The OTG is formatted correctly as the OTG is readable on other devices, but it seems like it just isn't being found by the N7. I'm baffled.

Check this thread: http://forum.xda-developers.com/showthread.php?t=3064562

Tried it on a full battery, still no luck.

tried to get it to work, any suggestions fellow XDAers? I'm in a real jam here

Check this thread: http://forum.xda-developers.com/show....php?t=3064562
Click to expand...
Click to collapse
Thanks, but I can't get the tablet to be recognized. I've tried it in multiple windows computers with both USB 2 and 3.

Have you tried adb/fastboot?

Have you tried adb/fastboot?
Click to expand...
Click to collapse
I am able to fastboot, but still can't get the pc to recognize that it's connected. The tablet takes a charge, but the pc never acknowledges that a device is connected, device manager never indicates a device is connected.

-If you don't have any Roms on internal storage, that's no good since you have TWRP.
-Try A different USB cable.
-Definitly make sure you have installed Google USB drivers.
-Have you tried ADB Sideload in twrp? Maybe TWRPs' adb will work better.
It looks like you need to update your bootloader as well, go with the latest factory images.
If you need to know where to find the above things I can point you to them. You must eventually get the PC to recognise it in fastboot though.

CrazyJ36 said:
-If you don't have any Roms on internal storage, that's no good since you have TWRP.
-Try A different USB cable.
-Definitly make sure you have installed Google USB drivers.
-Have you tried ADB Sideload in twrp? Maybe TWRPs' adb will work better.
It looks like you need to update your bootloader as well, go with the latest factory images.
If you need to know where to find the above things I can point you to them. You must eventually get the PC to recognise it in fastboot though.
Click to expand...
Click to collapse
Thanks. Everything hinges on the PC being able to recognize that I'm attempting to connect the tablet (or for the tablet to recognize that I've attached the OTG).
I have tried multiple USB cables and ensured that the drivers are installed on the multiple PCs I've attached to.
I have tried to ADB sideload in TWRP, but since none of the PCs recognize that the tablet is connected to the PC, ADB won't work.
Again, it's not that the drivers are not installed, but rather the PC not recognizing that I have attached a device through the USB (no sound, no pop-up, nothing in the device manager). It is extremely frustrating, especially since the device charges via the USB from the PC.

DorianX said:
Check this thread: http://forum.xda-developers.com/showthread.php?t=3064562
Click to expand...
Click to collapse
CrazyJ36 said:
Have you tried adb/fastboot?
Click to expand...
Click to collapse
Still no luck, any other recommendations?

Device Manager doesn't even show something like "qualcomm_qloader"? That's seems worse than any other hard brick I've seen.
-OTG should be FAT32 formated (probably is).
-We're you using Lollipop with that 4.02 bootloader? I believe that was A prerequisite for installing Lollipop which may have cause the tablet to not show on the PC.
- Nexus Root Toolkit has different methods for installing drivers http://www.wugfresh.com/faqs/
-Found this thread http://forum.xda-developers.com/showthread.php?t=2404297&page=1
Shows holding power for A minute got theres' to start doing stuff. It' A different recovery issue though.
Hate to be A downer, I hard bricked A galaxy s4 I had for only 5 days last month. That never turned on again. It's not fun.

I had the same issue. The only way I could fix was a full adb restore. I tried several other ways and none worked.
sent from my Hyperdrive powered G Note 10.1

CrazyJ36 said:
Device Manager doesn't even show something like "qualcomm_qloader"? That's seems worse than any other hard brick I've seen.
-OTG should be FAT32 formated (probably is).
-We're you using Lollipop with that 4.02 bootloader? I believe that was A prerequisite for installing Lollipop which may have cause the tablet to not show on the PC.
- Nexus Root Toolkit has different methods for installing drivers http://www.wugfresh.com/faqs/
-Found this thread http://forum.xda-developers.com/showthread.php?t=2404297&page=1
Shows holding power for A minute got theres' to start doing stuff. It' A different recovery issue though.
Hate to be A downer, I hard bricked A galaxy s4 I had for only 5 days last month. That never turned on again. It's not fun.
Click to expand...
Click to collapse
Nothing shows in the device manager. I was using KitKat on the tablet.
Turns on without an issue, opens TWRP with no issue.
when connected to the PC nothing occurs, not when it's on the Google screen, not when it's in TWRP, not in Fastboot, not when it's restarting. Nothing.
if it was the driver being missing, I'd at least see the device attached, just not communicating properly
sorry to hear about your GS4

The Apostle said:
I had the same issue. The only way I could fix was a full adb restore. I tried several other ways and none worked.
sent from my Hyperdrive powered G Note 10.1
Click to expand...
Click to collapse
if you truly had the same exact problem, how were you able to use ADB if your device wasn't recognized on a PC or OTG?

Welp, that would be my fault for not completely reading. My apologies.
sent from my Hyperdrive powered G Note 10.1

The Apostle said:
Welp, that would be my fault for not completely reading. My apologies.
sent from my Hyperdrive powered G Note 10.1
Click to expand...
Click to collapse
it's alright, thanks for the thought.
I'm just hoping since I can get into TWRP someone has an idea of how I can get it to recognize the OTG or the PC to see it and I can get into ADB.

Corrupted usb port on the tablet? Maybe broken pin. Try to examine it. It can happen that it is being charged but not identified by the pc because of a faulty port. Try live install of ubuntu to chech if it sees the device.

zandgreen said:
Corrupted usb port on the tablet? Maybe broken pin. Try to examine it. It can happen that it is being charged but not identified by the pc because of a faulty port. Try live install of ubuntu to chech if it sees the device.
Click to expand...
Click to collapse
the port looks perfectly fine, I was thinking the same thing, but there doesn't seem to be any damage. I almost wish it was damaged so I could at least assume that's the problem and just trash the thing.

No more usb access on windows 10

Hi all,
I have a Oneplus 3 with the last update (OxygenOS 5.0.4) and I can't access to my files with an USB cable.
I try on 3 computers with differents cables, and the OTG parameter on ON but nothing works.
Drivers are normally ok.
Do you have a solution?
Best regards,
Jckbrtn

jckbrtn said:
Do you have a solution?
Click to expand...
Click to collapse
Try to turn on usb debugging in developer options

mar.ur said:
Try to turn on usb debugging in developer options
Click to expand...
Click to collapse
Hi,
Thanks but it doesn't work and I never need to do that before.
I don't understand why it doesn't work anymore.
I hadn't try nothing new on my phone.
I think I will try to reset it...
Best regards,
Jckbrtn

@jckbrtn is there connecting with pc in recovery mode ? I mean adb commands

mar.ur said:
@jckbrtn is there connecting with pc in recovery mode ? I mean adb commands
Click to expand...
Click to collapse
I just try to connect my Oneplus with USB cable like I always use to do.
ADB drivers are installed on my PC and I only have the original recovery.
I never try to root this smartphone.
With a OneplusX on LineageOS, no problem. See screenshot:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

Looking at your photo, have your tried to tap the second option...?

150208 said:
Looking at your photo, have your tried to tap the second option...?
Click to expand...
Click to collapse
Picture is for my OneplusX. It works for the OneplusX on the same computer but not for the Oneplus 3.
I don't have this menu in notification.

jckbrtn said:
Picture is for my OneplusX. It works for the OneplusX on the same computer but not for the Oneplus 3.
I don't have this menu in notification.
Click to expand...
Click to collapse
Oh i see
Try developer options, if i remember it right, i believe there is a setting about USB access in OOS.
Other than that i don't know except factory reset, re-install the PC, or bad usb port (in either of phone/pc).
I have this issue once, but it because my bad usb port on my PC motherboard.

jckbrtn said:
Picture is for my OneplusX. It works for the OneplusX on the same computer but not for the Oneplus 3.
I don't have this menu in notification.
Click to expand...
Click to collapse
Go through and remove the drivers for all the one plus device then connect the 3. The drivers for the two are corrupting each other. It is a known issue with the drivers for this device. I have to reinstall the drivers on every connect and disconnect from USB.

zelendel said:
Go through and remove the drivers for all the one plus device then connect the 3. The drivers for the two are corrupting each other. It is a known issue with the drivers for this device. I have to reinstall the drivers on every connect and disconnect from USB.
Click to expand...
Click to collapse
I only have drivers for the 3. For th OneplusX with the usb, no problem.
Drivers removed but it doesn't works. I think I'll try a reset of my device in a few days to see...
I try on 3 windows computers with differents cables (also the Oneplus one), drivers, no drivers... don't know....

jckbrtn said:
I only have drivers for the 3. For th OneplusX with the usb, no problem.
Drivers removed but it doesn't works. I think I'll try a reset of my device in a few days to see...
I try on 3 windows computers with differents cables (also the Oneplus one), drivers, no drivers... don't know....
Click to expand...
Click to collapse
With the one plus devices you can never tell. It could be anything from software to hardware. Next time you connect pull a log cat this might help.

So I try a factory reset: don't work
I downgrade to oxygen 5.0.3 and 5.0.1: don't work
I try on an other laptop where I never plug my oneplus or install drivers/adb: don't work
I also try with different cables (original from oneplus include): don' work
With otg option on, usb debugging on, ... or without, don't work!
And best is I can't install LineageOS as I have no access on my PC

zelendel said:
With the one plus devices you can never tell. It could be anything from software to hardware. Next time you connect pull a log cat this might help.
Click to expand...
Click to collapse
Yes, I think it's hardware. USB-C don't work with OTG adapter (USB-C to USB and USB key).
Log cat? How to?

I just bought an used 3T and have the same problem. I have tried every possible software solution I guess I have to try to replace USB port but if it doesn't help I don't know what I'll do...

I had the same issue but a fix I found to work was when my Oneplus 3 was plugged into my computer, the dropdown notification that says "Android System" - USB charging this device can be changed to transfer files and after that option is picked, my phone is detected by my computer. Maybe this will help some of you

stingerbs said:
I had the same issue but a fix I found to work was when my Oneplus 3 was plugged into my computer, the dropdown notification that says "Android System" - USB charging this device can be changed to transfer files and after that option is picked, my phone is detected by my computer. Maybe this will help some of you
Click to expand...
Click to collapse
Problem is I don't have this menu anymore since my usbc port is not working

stingerbs said:
I had the same issue but a fix I found to work was when my Oneplus 3 was plugged into my computer, the dropdown notification that says "Android System" - USB charging this device can be changed to transfer files and after that option is picked, my phone is detected by my computer. Maybe this will help some of you
Click to expand...
Click to collapse
I'm waiting for a response of the oneplus support. My smartphone is still under warranty so I asked for a RMA.
I had to make a video of me connecting the phone to my computer to show the issue.
I also made a video with an other usbc smartphone to show that all is working.

jckbrtn said:
I'm waiting for a response of the oneplus support. My smartphone is still under warranty so I asked for a RMA.
I had to make a video of me connecting the phone to my computer to show the issue.
I also made a video with an other usbc smartphone to show that all is working.
Click to expand...
Click to collapse
So after 2 weeks of mail contact, my smartphone was sent from Belgium to Poland monday.
I received my repaired smartphone on wednesday.
Technical support very good! Mail support very complicated...

Hardbricked, msmtool gives error 258

hello there guys, im new here and also desperate
unfortunately im struggling revive my beloved op3. i am getting a strange error, cant really seem to find many thing about it. so what happened is i was about to switch profile on the phone when it froze and stuck in bootloop, so i decided since nothing else worked to wipe everything off the phone. so it all went great, it was wiping data for atleast an hour when i decided to plug in to charge just in case, but the cable i used was fauilty so i ended up drained battery. ince then i am not able to recover it unfortunately.
in msm tool, it stucks at downloading chace.img, then afetr a couple of seconds i get an error:
firehose check rsp failed, errno:258
downloading chace.img failed
iam very out of ideas what to do from here. only thing is after this the led glows light green-yellowish
any suggestion?
other thing what i realised:
when it sais hold the volume up button and connect to usb, nothing happens. unless i press volume up+power button. could it be the reason? no matter how long im holding only volume up and connect it to pc, nothing will happen.
thanks for reading,
Tomi
and aslo this is what i get in the log
Device Arrival: \\?\USB#VID_05C6&PID_9008#6&2af7e5e9&0&1#{86e0d1e0-8089-11d0-9ce4-08003e301f73}
m_ImageHwId 16: 009470E12A703DB9
m_PhoneHwId 24: 009470E12A703DB9
UFS Inquiry Command Output: SAMSUNG KLUCG4J1CB-B0B1 0800
UFS info Vendor = samsung, TotalLogicalBlocks = 124993536
[7] HANDSET_TYPE_64G:
[7] Downloading rawprogram0 Label: cache FileName: cache.img
Device Remove: \\?\USB#VID_05C6&PID_9008#6&2af7e5e9&0&1#{86e0d1e0-8089-11d0-9ce4-08003e301f73}

Maszkos said:
hello there guys, im new here and also desperate
unfortunately im struggling revive my beloved op3. i am getting a strange error, cant really seem to find many thing about it. so what happened is i was about to switch profile on the phone when it froze and stuck in bootloop, so i decided since nothing else worked to wipe everything off the phone. so it all went great, it was wiping data for atleast an hour when i decided to plug in to charge just in case, but the cable i used was fauilty so i ended up drained battery. ince then i am not able to recover it unfortunately.
in msm tool, it stucks at downloading chace.img, then afetr a couple of seconds i get an error:
firehose check rsp failed, errno:258
downloading chace.img failed
iam very out of ideas what to do from here. only thing is after this the led glows light green-yellowish
any suggestion?
other thing what i realised:
when it sais hold the volume up button and connect to usb, nothing happens. unless i press volume up+power button. could it be the reason? no matter how long im holding only volume up and connect it to pc, nothing will happen.
thanks for reading,
Tomi
and aslo this is what i get in the log
Device Arrival: \\?\USB#VID_05C6&PID_9008#6&2af7e5e9&0&1#{86e0d1e0-8089-11d0-9ce4-08003e301f73}
m_ImageHwId 16: 009470E12A703DB9
m_PhoneHwId 24: 009470E12A703DB9
UFS Inquiry Command Output: SAMSUNG KLUCG4J1CB-B0B1 0800
UFS info Vendor = samsung, TotalLogicalBlocks = 124993536
[7] HANDSET_TYPE_64G:
[7] Downloading rawprogram0 Label: cache FileName: cache.img
Device Remove: \\?\USB#VID_05C6&PID_9008#6&2af7e5e9&0&1#{86e0d1e0-8089-11d0-9ce4-08003e301f73}
Click to expand...
Click to collapse
When you hold volume up and connect to the PC, it should be recognised. If not, it is either of two things viz. the required drivers are not installed or the phone is really DEAD. So follow the steps given in the Unbrick Guide scrupulously and check. I have used it and revived my phone successfully.

tnsmani said:
When you hold volume up and connect to the PC, it should be recognised. If not, it is either of two things viz. the required drivers are not installed or the phone is really DEAD. So follow the steps given in the Unbrick Guide scrupulously and check. I have used it and revived my phone successfully.
Click to expand...
Click to collapse
Okay thanks for that. I'll redo everything step by step, and I'll let you know if it worked out which I hope so.
One more question: since I had the phone bricked while restoring it to factory and ran out of battery, can it cause hardware failure? Or any idea what is the meaning of the this 258 error code? I tried to look up on the internet but didn't find anything about it.
Cheers
Tomi

Maszkos said:
Okay thanks for that. I'll redo everything step by step, and I'll let you know if it worked out which I hope so.
One more question: since I had the phone bricked while restoring it to factory and ran out of battery, can it cause hardware failure? Or any idea what is the meaning of the this 258 error code? I tried to look up on the internet but didn't find anything about it.
Cheers
Tomi
Click to expand...
Click to collapse
Did you charge the phone subsequently? Does it take the charge? If the battery is completely dead, the phone may not revive unless the battery gets some charge. You may try to charge it or with another battery if that is available.

tnsmani said:
Did you charge the phone subsequently? Does it take the charge? If the battery is completely dead, the phone may not revive unless the battery gets some charge. You may try to charge it or with another battery if that is available.
Click to expand...
Click to collapse
So I installed a fresh windows today did the whole thing from the a-z but the same issue occurs. I think the battery should be alright never had any problems with it. All I get is this man errno:258 nothing seems to work unfortunately..

Maszkos said:
So I installed a fresh windows today did the whole thing from the a-z but the same issue occurs. I think the battery should be alright never had any problems with it. All I get is this man errno:258 nothing seems to work unfortunately..
Click to expand...
Click to collapse
I hope that you are running a regular Win 10 PC that too Intel (not AMD) and not through VM. Also I hope that you disabled the check for driver signing BEFORE installing the drivers. Your issue seems to be the drivers. May be re-download the drivers. Read the entire page. Use another PC or Laptop and different USB ports especially v2.0 and not v3.0. Repeat until you succeed.

tnsmani said:
I hope that you are running a regular Win 10 PC that too Intel (not AMD) and not through VM. Also I hope that you disabled the check for driver signing BEFORE installing the drivers. Your issue seems to be the drivers. May be re-download the drivers. Read the entire page. Use another PC or Laptop and different USB ports especially v2.0 and not v3.0. Repeat until you succeed.
Click to expand...
Click to collapse
Cool I will, it's a regular win10, signature should be ok, I tried it on 3 different laptops, 2ofthem were older ones but no success. I really hope it is just a driver issue since my problem occured while formatting the phone in bootloader. I'm not sure about the usb ports I'll check that out aswell.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
I'll let you know if there's any update!
Ps I get a greenish light after the man tool fails to upload the cache.img
Sometimes it turns orange aswell. Is that a good sign?
Thank you tnsami for your time and effort, really appreciate it

Maszkos said:
Cool I will, it's a regular win10, signature should be ok, I tried it on 3 different laptops, 2ofthem were older ones but no success. I really hope it is just a driver issue since my problem occured while formatting the phone in bootloader. I'm not sure about the usb ports I'll check that out aswell.
View attachment 4716364
I'll let you know if there's any update!
Ps I get a greenish light after the man tool fails to upload the cache.img
Sometimes it turns orange aswell. Is that a good sign?
Thank you tnsami for your time and effort, really appreciate it
Click to expand...
Click to collapse
Did you ever solve it?

Baxter777 said:
Did you ever solve it?
Click to expand...
Click to collapse
Noo not yet unfortunately I was carried away by other things, I am about to look into it now again, might find a solution for it. Any luck over there?

Have you tried another computer

Baxter777 said:
Did you ever solve it?
Click to expand...
Click to collapse
kallum7 said:
Have you tried another computer
Click to expand...
Click to collapse
I did, but they all had usb 3.0 as far as I can remember, so ill try it with usb 2 soon, maybe next week or so. That is my last resort.
I checked the battery it takes the charge, even tough it only had approximately 3volt in it instead of 3.8v would you think a new battery is essential?

What I would do is buy another charging cable and then try and charge it up and then try and unbrick the phone

kallum7 said:
What I would do is buy another charging cable and then try and charge it up and then try and unbrick the phone
Click to expand...
Click to collapse
Yeah, did that too original cable, charger. So is this a communication error between the phone and PC is it?

Try going into the device manager on windows and go to ports and uninstall OnePlus com port drivers and reinstall them