This guide will help you gain back your IMEI on your Micromax Canvas Knight [Only if the Baseband is not lost].
NOTE :
1.Only for ROOTED devices !
2. This guide is useful only when the 'Baseband Version' of your device is avilable. If the device is showing 'Unknown' in the Baseband tab in the About device section , then you will have to use a different method.
3. This method is also applicable for many other MTK6589 and MTK6592 devices [Even more , maybe].
STEP 1 :
1.1 Go ahead and install Mobile Uncle Tools from Playstore .
STEP 2 :
2.1 Open the Mobile Uncle Tools and grant Super User permissions
2.2 Click on Engineer Mode and then click on 'Engineer Mode (MTK)'
This will take you to the MTK Engineer Mode.
STEP 3 :
3.1 Now swipe right once and you will find the ' Connectivity ' tab.
3.2 Under this tab , you will find ' CDS Information '. Click on that.
3.3 Next , find ' Radio Information '.
3.4 On opening Radio Information , you will find 2 options : Phone 1 and Phone 2 .
This denotes the IMEI slots for the 2 SIM cards.
STEP 4 :
4.1 You'll find a page with ' AT+ __________________ '
4.2 Now , just after the '+' , type 'EGMR' . As you start typing , it will automatically pop-up four messages.
4.3 Select the first one from that : AT+EGMR=1,7,"".
4.4 Between the two double - inverted commas , type in the IMEI 1 . You can find the IMEI from the backside of the device [If at all you have not removed that TAG] like this .
AT+EGMR=1,7," 15 digit IMEI number "
4.5 Now click on " SEND AT COMMAND ".
You will receive a small toast message like this " AT Command is msent ".
That message shows that the IMEI has been restored !
Now , repeat steps 4.1 , 4.2 and 4.3 for Phone 2 .
But , in step 4.3 , select " AT+EGMR=1,10, "" " ( It is the second option )
Repeat rest of the steps and you will have both the IMEI written on your device.
To check , just type *#06# on dial-pad and it will show your IMEI numbers .
STEP 5 :
* Reboot !
And then the SIM cards will be detected .
Thanks for the thread . Good job :good:
CDS is blacked out. What to do?
revolutionyzer said:
This guide will help you gain back your IMEI on your Micromax Canvas Knight [Only if the Baseband is not lost].
NOTE :
1.Only for ROOTED devices !
2. This guide is useful only when the 'Baseband Version' of your device is avilable. If the device is showing 'Unknown' in the Baseband tab in the About device section , then you will have to use a different method.
3. This method is also applicable for many other MTK6589 and MTK6592 devices [Even more , maybe].
STEP 1 :
1.1 Go ahead and install Mobile Uncle Tools from Playstore .
STEP 2 :
2.1 Open the Mobile Uncle Tools and grant Super User permissions
2.2 Click on Engineer Mode and then click on 'Engineer Mode (MTK)'
This will take you to the MTK Engineer Mode.
STEP 3 :
3.1 Now swipe right once and you will find the ' Connectivity ' tab.
3.2 Under this tab , you will find ' CDS Information '. Click on that.
3.3 Next , find ' Radio Information '.
3.4 On opening Radio Information , you will find 2 options : Phone 1 and Phone 2 .
This denotes the IMEI slots for the 2 SIM cards.
STEP 4 :
4.1 You'll find a page with ' AT+ __________________ '
4.2 Now , just after the '+' , type 'EGMR' . As you start typing , it will automatically pop-up four messages.
4.3 Select the first one from that : AT+EGMR=1,7,"".
4.4 Between the two double - inverted commas , type in the IMEI 1 . You can find the IMEI from the backside of the device [If at all you have not removed that TAG] like this .
AT+EGMR=1,7," 15 digit IMEI number "
4.5 Now click on " SEND AT COMMAND ".
You will receive a small toast message like this " AT Command is msent ".
That message shows that the IMEI has been restored !
Now , repeat steps 4.1 , 4.2 and 4.3 for Phone 2 .
But , in step 4.3 , select " AT+EGMR=1,10, "" " ( It is the second option )
Repeat rest of the steps and you will have both the IMEI written on your device.
To check , just type *#06# on dial-pad and it will show your IMEI numbers .
STEP 5 :
* Reboot !
And then the SIM cards will be detected .
Click to expand...
Click to collapse
this command is not allowed in UserBuild (Mobile Uncle Tools) :
If you are getting this error then put space between AT and +EGMR
If You cant root your phone with latest KingRoot then try Older versions e.g. 4.8.1
Successfully Tried on MicroMax Knight A350
Related
Her is my story with android 4.3
- i had installed a custom firmware to my galaxy note 2 3 months ago >
- i found a problem that every few days it asks for backup account and i should restore all my Google account.
- i tried to downgrade to 4.1.2 but did not work ( changed my IMIE )
- i installed 4.3 again using Odin
- figured that CSC unknown
- i used Odin to install individual CSC re fare to my country Egypt .
my problems now :
1- Bluetooth dos not work and when i try to activate it the mobile halted (i tried to use your application Bluetooth fix it says no Bluetooth setting folder )
2- when i connect the mobile to the PC i have to use code *#7284# and useusb mod as PDA every time >
3- some times i lose network .
4- it takes so long to unlock the screen .
i wish you can help me
--
Hossam Shawky
no reply
--
Hossam Shawky[/IS IT SO HARD????]
When i put on the chip, the IMEI set to NULL
I've already tried many ways to fix this, but no success...
Please, someone help me!
I don't want to lost my optimus G!
thanks
You should restore your imei with your EFS backup...have you unlock with freegee or you are completely stock and have never touched nothing?
Sent from my LG-F180K using XDA Free mobile app
Sorin90 said:
You should restore your imei with your EFS backup...have you unlock with freegee or you are completely stock and have never touched nothing?
Sent from my LG-F180K using XDA Free mobile app
Click to expand...
Click to collapse
first of all thanks by your attention!
I do not have a backup...
i don't know what to do...
i've unlocked with freegee many times...
but this time i got this problem!
renanreno said:
first of all thanks by your attention!
I do not have a backup...
i don't know what to do...
i've unlocked with freegee many times...
but this time i got this problem!
Click to expand...
Click to collapse
Retrieve IMEI in your LG Optimus G in case of not make previous backup
The method I describe below was developed for LG G2 but has been tested successfully in the Optimus G so it's perfectly useful:
Requirements:
- The mobile must have the Stock ROM (4.1.2 or 4.4.2).
- Download Tool QSTP:
https://mega.co.nz/#!2phwmYhY!DXozTvsU4pDD5PKJcYWnuC5nKQEA0skuFeN-90dFjQU
- Download Tool IMEI Converter:
https://dl.dropboxusercontent.com/u/84115590/IMEI-Converter.zip
Steps:
1 Unzip the tool IMEI Converter to a folder:
2 Unzip tool QPST 2.7_build_4.11 in a folder and run the installation file (Setup) to install on your computer:
3 Now on the phone to enable USB Debugging. If you do not know how you can find this option in the Settings> Developmet Options>USB debugging and activate.
5 Connect the device to your computer.
6 Run the QSPT, to set it up you are clicking on the PORTS tab, then click on the ADD NEW PORT option.
7 The current port as should COM4 or 5. Note: If you do not recognize these ports any port try to recognize the phone or another PC in the latter case.
8 Select the port and click OK. The port should show the active phone.
9 Select the phone (APQ8064) and click the Download Software option from the Start Clients menu.
10 Now give click the Backup tab. It should show the phone port.
11 Click the Start tab to start doing the backup.
12 Now find the folder named BIN located in the path:
C:/program files/Qualcomm/QSPT/, open the BIN folder and execute the file RF_NV_Manager
13 Click in File> Read from phone. The IMEI number of the phone should appear in item number 550: NV_UV_IMEI_1
If you appear get an error
14 They select OK and then click on File> Read RF NVitems supported.
15. Click on item 550. Should be displayed 9 boxes in white (empty).
16 Now run the file IMEIConverter.exe
17 Then write your IMEI (15 digits) in the Enter IMEI field. If you do not know what they find in the phone box, in some models even Optimus G is glued on the back thereof, or in the phone bill.
*** - Then click on the button <CONVERT IMEI>.
** - 18 Should appear two groups of 9 digits
18. In the program RF_NV_Manager activated the Hex box
19 Now 9 boxes appear, type the numbers generated IMEI Convert starting from the left, should be written in each box two digits consecutively until the 9 squares remain full.
20 Once the 9 squares are filled correctly you have to go to Setting option> comport> and select the port to which you are connected again and give OK
21 Select the Write NV tab.
22 Then click File> Readfrom phone.
The item number 550 should now appear.
24 Disconnect the USB cable and restart the phone.
25 Open the dialer (phone dialer) dial *#06# You should display the IMEI of your phone and the phone should be connected to the carrier signal without problems.
Important Note:
- If you give Error in step 13 run again and Method in step 13 before you dial them run error step 20.
Good luck and any thing sending me a message and i help. :good:
whit efs profesional is more easy
syverman said:
whit efs profesional is more easy
Click to expand...
Click to collapse
I do not know the method you mentioned, but in any case I have already given an effective alternative for him to solve your problem, since no one has helped so far.
Milos Rea said:
Retrieve IMEI in your LG Optimus G in case of not make previous backup
The method I describe below was developed for LG G2 but has been tested successfully in the Optimus G so it's perfectly useful:
Requirements:
- The mobile must have the Stock ROM (4.1.2 or 4.4.2).
- Download Tool QSTP from this Post:
http://forum.xda-developers.com/showthread.php?t=1942417
- Download Tool IMEI Converter from this Post (item 2):
*http://forum.xda-developers.com/showthread.php?t=2701861
Steps:
1 Unzip the tool IMEI Converter to a folder:
2 Unzip tool QPST 2.7_378 in a folder and run the installation file (Setup) to install on your computer:
3 Now on the phone to enable USB Debugging. If you do not know how you can find this option in the Settings> Developmet Options>USB debugging and activate.
5 Connect the device to your computer.
6 Run the QSPT, to set it up you are clicking on the PORTS tab, then click on the ADD NEW PORT option.
7 The current port as should COM4 or 5. Note: If you do not recognize these ports any port try to recognize the phone or another PC in the latter case.
8 Select the port and click OK. The port should show the active phone.
9 Select the phone (APQ8064) and click the Download Software option from the Start Clients menu.
10 Now give click the Backup tab. It should show the phone port.
11 Click the Start tab to start doing the backup.
12 Now find the folder named BIN located in the path:
C:/program files/Qualcomm/QSPT/, open the BIN folder and execute the file RF_NV_Manager
13 Click in File> Read from phone. The IMEI number of the phone should appear in item number 550: NV_UV_IMEI_1
If you appear get an error
14 They select OK and then click on File> Read RF NVitems supported.
15. Click on item 550. Should be displayed 9 boxes in white (empty).
16 Now run the file IMEIConverter.exe
17 Then write your IMEI (15 digits) in the Enter IMEI field. If you do not know what they find in the phone box, in some models even Optimus G is glued on the back thereof, or in the phone bill.
*** - Then click on the button <CONVERT IMEI>.
** - 18 Should appear two groups of 9 digits
18. In the program RF_NV_Manager activated the Hex box
19 Now 9 boxes appear, type the numbers generated IMEI Convert starting from the left, should be written in each box two digits consecutively until the 9 squares remain full.
20 Once the 9 squares are filled correctly you have to go to Setting option> comport> and select the port to which you are connected again and give OK
21 Select the Write NV tab.
22 Then click File> Readfrom phone.
The item number 550 should now appear.
24 Disconnect the USB cable and restart the phone.
25 Open the dialer (phone dialer) dial * # 06 # You should display the IMEI of your phone and the phone should be connected to the carrier signal without problems.
Important Note:
- If you give Error in step 13 run again and Method in step 13 before you dial them run error step 20.
Good luck and any thing sending me a message and i help. :good:
Click to expand...
Click to collapse
I did everything but it is not with original imei of my carrier, is with another imei. Because?
Milos Rea said:
Retrieve IMEI in your LG Optimus G in case of not make previous backup
The method I describe below was developed for LG G2 but has been tested successfully in the Optimus G so it's perfectly useful:
Requirements:
- The mobile must have the Stock ROM (4.1.2 or 4.4.2).
- Download Tool QSTP from this Post:
http://forum.xda-developers.com/showthread.php?t=1942417
- Download Tool IMEI Converter from this Post (item 2):
*http://forum.xda-developers.com/showthread.php?t=2701861
Steps:
1 Unzip the tool IMEI Converter to a folder:
2 Unzip tool QPST 2.7_378 in a folder and run the installation file (Setup) to install on your computer:
3 Now on the phone to enable USB Debugging. If you do not know how you can find this option in the Settings> Developmet Options>USB debugging and activate.
5 Connect the device to your computer.
6 Run the QSPT, to set it up you are clicking on the PORTS tab, then click on the ADD NEW PORT option.
7 The current port as should COM4 or 5. Note: If you do not recognize these ports any port try to recognize the phone or another PC in the latter case.
8 Select the port and click OK. The port should show the active phone.
9 Select the phone (APQ8064) and click the Download Software option from the Start Clients menu.
10 Now give click the Backup tab. It should show the phone port.
11 Click the Start tab to start doing the backup.
12 Now find the folder named BIN located in the path:
C:/program files/Qualcomm/QSPT/, open the BIN folder and execute the file RF_NV_Manager
13 Click in File> Read from phone. The IMEI number of the phone should appear in item number 550: NV_UV_IMEI_1
If you appear get an error
14 They select OK and then click on File> Read RF NVitems supported.
15. Click on item 550. Should be displayed 9 boxes in white (empty).
16 Now run the file IMEIConverter.exe
17 Then write your IMEI (15 digits) in the Enter IMEI field. If you do not know what they find in the phone box, in some models even Optimus G is glued on the back thereof, or in the phone bill.
*** - Then click on the button <CONVERT IMEI>.
** - 18 Should appear two groups of 9 digits
18. In the program RF_NV_Manager activated the Hex box
19 Now 9 boxes appear, type the numbers generated IMEI Convert starting from the left, should be written in each box two digits consecutively until the 9 squares remain full.
20 Once the 9 squares are filled correctly you have to go to Setting option> comport> and select the port to which you are connected again and give OK
21 Select the Write NV tab.
22 Then click File> Readfrom phone.
The item number 550 should now appear.
24 Disconnect the USB cable and restart the phone.
25 Open the dialer (phone dialer) dial * # 06 # You should display the IMEI of your phone and the phone should be connected to the carrier signal without problems.
Important Note:
- If you give Error in step 13 run again and Method in step 13 before you dial them run error step 20.
Good luck and any thing sending me a message and i help. :good:
Click to expand...
Click to collapse
Dear Sir, I am using this process for restoring efs/Imei of my LG optimus G f180l. the port shows in my system COM5 and when i swich my phone in LG software mode . but in step 13 it gives the error(could not communicate in diagnostic mode) during backing up. please guide me what I have to do and what mistake m I doing. PLease
gm sheikh said:
Dear Sir, I am using this process for restoring efs/Imei of my LG optimus G f180l. the port shows in my system COM5 and when i swich my phone in LG software mode . but in step 13 it gives the error(could not communicate in diagnostic mode) during backing up. please guide me what I have to do and what mistake m I doing. PLease
Click to expand...
Click to collapse
put it in charge only, that help for me when i use it a long time ago
gm sheikh said:
Dear Sir, I am using this process for restoring efs/Imei of my LG optimus G f180l. the port shows in my system COM5 and when i swich my phone in LG software mode . but in step 13 it gives the error(could not communicate in diagnostic mode) during backing up. please guide me what I have to do and what mistake m I doing. PLease
Click to expand...
Click to collapse
Hi, if you get the error in step 13 test select Setting option> comport> and select the port to which you are connected again and give OK. Good luck
Hey guys, I will reactivate this topic a little. I ve got LG F180K and I converted it to E975 without doing EFS backup (still had imei number but no signal). I flashed modem for K and it still didnt work, flashed L modem and it...worked. No LTE and no 2G, only 3G, still imei.
What to do then if I want come back to F180K ROM? (NO EFS BACKUP)
If you unlocked using freegee the imei backup folder is their in your internal storage root folder. freegee backups even if you don't choose to.
akahroba said:
If you unlocked using freegee the imei backup folder is their in your internal storage root folder. freegee backups even if you don't choose to.
Click to expand...
Click to collapse
I didnt do freegee
BartxGamer said:
Hey guys, I will reactivate this topic a little. I ve got LG F180K and I converted it to E975 without doing EFS backup (still had imei number but no signal). I flashed modem for K and it still didnt work, flashed L modem and it...worked. No LTE and no 2G, only 3G, still imei.
What to do then if I want come back to F180K ROM? (NO EFS BACKUP)
Click to expand...
Click to collapse
Do this step for no signal if your IMEI is correct(not null).Root is necessary for this step
Install "SQLite editer" from Google play to open "settings.db" in location "Data\data\com.android.providers.settings\database s" select "global" -> find "subscription_mode" change value "1" to "0" then save and exit.
kashifarif said:
Do this step for no signal if your IMEI is correct(not null).Root is necessary for this step
Install "SQLite editer" from Google play to open "settings.db" in location "Data\data\com.android.providers.settings\database s" select "global" -> find "subscription_mode" change value "1" to "0" then save and exit.
Click to expand...
Click to collapse
Are you sure about that?
renanreno said:
When i put on the chip, the IMEI set to NULL
I've already tried many ways to fix this, but no success...
Please, someone help me!
I don't want to lost my optimus G!
thanks
Click to expand...
Click to collapse
i have same problem due to convert f180k to e975. i have solved it by factory rest after flash and after factory reset (setting->backup and reset-> reset phone) restore IMEI and then again factory reset.
Factory reset after flash is main solution.
Sorry for necroing an old thread, but my lg g6 t- mobile h872 , suddenly says IMEI null after the latest 20a-e update. I never rooted, or flashed any custom roms before
What should I do?
This guide is only for Android smartphones who has problems with IMEI number on MTK chipsets….
“I am not responsible for any damage caused to your phone by using this”
Method 1 – Using Engineer Mode (You must have rooted your device before doing this procedure)
Open the Dialer and type *#*#3646633#*#* you will enter the MTK Engineering Mode or using Mobile Uncle APP Hit the Engineer Mode option and choose the Engineer Mode (MTK).
On EngineerMode Chosee Connectivity and click the CDS information option.
You will see Radio information there and after tapping on it. If you have dual SIM ANDROID then you will see TWO option select any one on which you want to write IMEI with.
Click Phone 1
At “AT+” line add : AT+EGMR = 1,7,”my_first_IMEI_code”
Click on “SEND AT” button below
For second SIM tap Phone 2 and type this command
AT+EGMR=1,10,”my_second_IMEI_code”
Click on “SEND AT COMMAND” button below a second time
Reboot phone
Verify codes with *#06#* if IMEI codes are ok
Method 2 – Using Terminal Emulator (You must have rooted your device before doing this procedure)
change imei with terminal emulator
Install Terminal Emulator
Launch the Terminal Emulator app
Type SU then press ENTER button to get Superuser permission
After that, type this command then press ENTER button
echo ‘AT+EGMR=1,7,”IMEI_NUMBER”‘ >/dev/pttycmd1
If you have dual SIM add this line
echo ‘AT+EGMR=1,10,”IMEI_NUMBER”‘ >/dev/pttycmd1
Last step, reboot your phone/tablet and DONE!
Method 3 – Using MTK Droid Tool
Download MTK droid tools and Extract on your PC/Laptop
Download Universal USB Driver
Enable USB debugging on the phone then connect it to the PC (don’t enable mass storage)
Install Universal USB Driver on the PC with the phone connected; you should get a message saying drivers installed successfully.
Launch MTK droid tools on the PC (still with phone connected to PC)
MTK droid tools should detect and display your phones details
Next you need to click the ROOT button so that it will temporary have Root shell access on your phone in order for it to make the script work on the background.
Click on IMEI/NVRAM
change imei mtkdroid tool
Put your 15 Digits IMEI Number that you can get at the back of your phone inside not the back cover if you have 2 IMEI you need to put that.
Then click Replace IMEI
Restart your phone if it isn’t automatically restarted
Your IMEI issue should have been resolved
I am not responsible for any damage to your phone,do it at your own risk.
Instead we can use mobileuncle tools application from play store for this we need root
Fix Found .
Ghostrider26 said:
This guide is only for Android smartphones who has problems with IMEI number on MTK chipsets….
“I am not responsible for any damage caused to your phone by using this”
Method 1 – Using Engineer Mode (You must have rooted your device before doing this procedure)
Open the Dialer and type *#*#3646633#*#* you will enter the MTK Engineering Mode or using Mobile Uncle APP Hit the Engineer Mode option and choose the Engineer Mode (MTK).
On EngineerMode Chosee Connectivity and click the CDS information option.
You will see Radio information there and after tapping on it. If you have dual SIM ANDROID then you will see TWO option select any one on which you want to write IMEI with.
Click Phone 1
At “AT+” line add : AT+EGMR = 1,7,”my_first_IMEI_code”
Click on “SEND AT” button below
For second SIM tap Phone 2 and type this command
AT+EGMR=1,10,”my_second_IMEI_code”
Click on “SEND AT COMMAND” button below a second time
Reboot phone
Verify codes with *#06#* if IMEI codes are ok
Method 2 – Using Terminal Emulator (You must have rooted your device before doing this procedure)
change imei with terminal emulator
Install Terminal Emulator
Launch the Terminal Emulator app
Type SU then press ENTER button to get Superuser permission
After that, type this command then press ENTER button
echo ‘AT+EGMR=1,7,”IMEI_NUMBER”‘ >/dev/pttycmd1
If you have dual SIM add this line
echo ‘AT+EGMR=1,10,”IMEI_NUMBER”‘ >/dev/pttycmd1
Last step, reboot your phone/tablet and DONE!
Method 3 – Using MTK Droid Tool
Download MTK droid tools and Extract on your PC/Laptop
Download Universal USB Driver
Enable USB debugging on the phone then connect it to the PC (don’t enable mass storage)
Install Universal USB Driver on the PC with the phone connected; you should get a message saying drivers installed successfully.
Launch MTK droid tools on the PC (still with phone connected to PC)
MTK droid tools should detect and display your phones details
Next you need to click the ROOT button so that it will temporary have Root shell access on your phone in order for it to make the script work on the background.
Click on IMEI/NVRAM
change imei mtkdroid tool
Put your 15 Digits IMEI Number that you can get at the back of your phone inside not the back cover if you have 2 IMEI you need to put that.
Then click Replace IMEI
Restart your phone if it isn’t automatically restarted
Your IMEI issue should have been resolved
I am not responsible for any damage to your phone,do it at your own risk.
Click to expand...
Click to collapse
Please thank me if i helped you.
Fix found : -> http://forum.xda-developers.com/canvas-a1/general/fix-imei-perfect-fix-android-imei-t2943567
this will work in old versions, I tried in Engineer Mode v1.8.0, CDS Information is gone, had to flash my device with Android 5.1 and probably an older version of Engineer Mode app
Imei change mtk 6753 homtom ht20 pro android 6.0 sdk 23
NO ROOT
In dialler
*#*#12306#*#*
bring you to secret sub menu in mtk engineering mode
not available in this menu by using this code to *#*#3646633#*#* that option change imei is not available in NORMAL MTK Engineering MODE as CDS information witch one REQUIRED ROOT PERMISSION TO ADD CDS information IN SUB MENU IN NORMAL MTK Engineering MODE
Error shown this command is not allowed in user build. please tell what to do next
Error shown this command is not allowed in user build. please tell what to do next
kbsoni156 said:
Error shown this command is not allowed in user build. please tell what to do next
Click to expand...
Click to collapse
Put a space after AT like "AT +" and not "AT+". Rest should be written as above..
I recently found a problem while doing method 1
"This command is not allowed in user build"
So the solution for that is:-
When we are writing
AT+EGMR = 1,7,”IMEI_code”
we have to give a space b/w AT and +
so final command will be like this
AT +EGMR=1,7,"IMEI_code"
Hit thanks if it worked for u
vinaykharayat said:
I recently found a problem while doing method 1
"This command is not allowed in user build"
So the solution for that is:-
When we are writing
AT+EGMR = 1,7,”IMEI_code”
we have to give a space b/w AT and +
so final command will be like this
AT +EGMR=1,7,"IMEI_code"
Hit thanks if it worked for u
Click to expand...
Click to collapse
FWIW, this doesn't work on a BLU Vivo 5R running Nougat. Gives the same not allowed error with or without the space.
lugnut2099 said:
FWIW, this doesn't work on a BLU Vivo 5R running Nougat. Gives the same not allowed error with or without the space.
Click to expand...
Click to collapse
And just to add on, the terminal commands don't work either. They're accepted without any kind of error, but upon reboot there's still nothing there.
Thanks
It worked perfectly on Lenovo tab 2 a8-50lc, couldn't click thank you button though, its greyed out.
P.s: must have root access. Tried without root gave not allowed in userbuild.
lugnut2099 said:
And just to add on, the terminal commands don't work either. They're accepted without any kind of error, but upon reboot there's still nothing there.
Click to expand...
Click to collapse
No error message either, but not working also.
//Tested on ZTE Blade V10, Android 9, V1.8
Not to be confused with V16 cuz its not the official version
bug fixes:
1. facebook app videos working
2. games such as vector, cut the rope, wheres my water etc working
3. camera is much faster
4. I think the over flashlight issue is solved (earlier while capturing pics the flash used to be more sometimes on a shiny surface)
rom link
http://support.moulnisky.com/index.php?dir=Micromax/00_A%20Serie/A210/SW%20Versions/V3_28.08.14/
Instructions:
Install it by SPflashtools
1.load the scatter file
2. do not press the download button instead press the firmware update button
(if you press the download it wont work and give an error "PMT CHANGE FOR THE ROM IT MUST BE DOWNLOAD")
3. connect your canvas 4 to be flashed
after the phone starts up the wifi NVram error will occur though wifi will work. so to solve this follow these steps to flash the mac id of wifi:
download the tool
https://www.4shared.com/rar/kHy8lnKhba/imei_sn_writer_v153.html
1. unzip and open the tool
2. In your canvas 4 goto settings>about phone>status>WiFi MAC address
note down the address in the notepad
3.In the tool
i. select platform: smart phone
ii. under that select the USB option
iii. click on DB and browse for the Database folder of the V3 rom
APDB_MT6589_S01_MAIN2.1_W10
BPLGUInfoCustomAppSrcP_MT6589_S00_MOLY_WR8_W1248_MD_WG_MP_V6_P18
open both these files
iv. tick on the wifi and input the wifi mac id u just noted.
v. switch off your phone
vii. click on START button and connect usb cable
done
video for flashing imei via IMEI and SN writer (same procedure to flash the wifi mac id)
https://www.youtube.com/watch?v=HprM5ZwY7HI
Password For The Rar
ashutoshtaikar said:
after the phone starts up the wifi NVram error will occur though wifi will work. so to solve this follow these steps to flash the mac id of wifi:
download the tool
https://www.4shared.com/rar/kHy8lnKhba/imei_sn_writer_v153.html
Click to expand...
Click to collapse
The Rar Is Password Protected and Heres The Password : [email protected]
:good:
So guys here is the simplest possible guide to enable LTE+ in your realme 2 pro.
Without wasting your time let's get started.
Let's discuss the all steps one by one but keeping it short still detailed.
1. Connect Your phone to PC make sure u enabled USB debugging and USB file transfer as preferred connection type.
2. Open CMD in your PC and type adb devices . If your device showed in attached device list and then proceed next step . If not follow This
3. Type adb devices . It must show ur device serial number allow USB debugging popup from phone
4. Then type adb shell
5. Then type su and allow super user access from your phone .
6. Copy and paste the below command
setprop sys.usb.config rndis,diag,adb
7. Now install QCOM drivers according to your PC specs like 32 bit or 64 bit . Download From here 32 bit and for 64bit
8. Now go to device manager, and ur device will be listed under other devices.(In most cases)
9. Now, right click on it, click on update driver, select driver from my pc( 2nd option), let me choose manually (a
gain 2nd option), now many device types will be listed, scroll and select ports(COM and LPT). Now from manufact
urer menu, scroll and select qualcomm incorporated then in the right menu, select first one, that is qualcomm diagno
stics interferance 3197, NOTE: Do it series wise and and the port should be qualcomm diagnostics interfrance 3197
only ( just the number here must be in 3 thousands and not 9thousands or 9 hunderds). Most probably u will find it i
n the top of the list.
10. Now install QPST download from Here
11. Now if you see 1 phones 1 Port in bottom left(jump to step (14) else keep following)
12. Click on add new port found on right bottom corner
13. Tick QC Diagnostic ports only and select shown port and select ok(repeat and add all listed ports if not detected)
14. Click on start clients->EFS exploprer and click ok
15. Navigate to NV->Item-files->rffnv
16. Now you will get a lot of files there . What u have to do is replace a file named 00028874 . Here is the new file link 00028874
17. Make sure u replaced properly and the file name should b same as before
18. Click on View->Refresh
19. After refresh check if file present or not
20. If the file is present then that's it disconnect you phone from PC .
21. Reboot and play some YouTube videos either u are getting 4g+ or not .
thats it it's that much easy no rocket science nothing .
Disclaimer:-
LTE + depends on various factors like network strength , ur geographical area, traffic on ur area etc etc so keep all things in mind .
Credit :-
1 . Subhadeep das (Ares) 1:- For Bringing this topic to our community that it's even possible
2. Kartik kala :- For trying 1st time and making the 1st guide .
3. Assus Zenfone community :- For giving reference to a rough guide and for all file links
Telegram you can join here for any type of support or help or doubt