i my s3 was on a lollipop cm based rom (bean stalk i think)
i used odin to bring it to stock nj2 (from this thread: http://forum.xda-developers.com/gal.../stock-l710vpudnj2-pc-odin-flashable-t3007847 )
now when i try to boot up my phone its is stuck
on the screen that says samsung (the font is pulsing) and my led is pulsing blue and cyan
any help would be apreciated
problem solved
Related
White "Samsung" text on boot after flashing stock rom from custom cyanogen mod.
I had Cyanogen mod installed and was having a lot of glitches/freezes. I downloaded and installed the stock ATT rom (UCDLK3) and flashed it to my device following these steps.
http://androidromupdate.com/2012/08...-sgh-i747-to-original-factory-stock-firmware/
After doing so, I am stuck on bootup with white "Samsung" text.
I found this thread which had a suggested answer, but my phone won't boot into recovery mode. When I try to boot into recovery mode, i see small text at the top that says "Recovery rebooting...", but then it flashs "Samsung" quickly, then goes back to being stuck with the white "Samsung" text.
How do I boot into recovery mode to wipe/data that may be preventing me from booting properly?
Ok what phone do you have? This is the forums for the L710 Sprint phone that link you posted is for a different S3. Hopefully you haven't bricked your phone. And that second link you found is for an HTC phone. Your all over the place.
Sent from the future via Xparent Green Tapatalk 2
Hey guys. I was running Omega rom for a while, and today i decied i would flash 4.3 paranoid android on my n7100, but when i tried to flash, it kinda went bad, first time it booted with no problem but than i wanted to reboot it to insert SIM and i got stuck on Samsung Galaxy NOTE II N7100 White text screen. I tried wiping everything, reflashin PA and CM10.1 but i cant get past the white text.Not even Boot Animation starts. I can get to Recovery no problem and I even tried reflashing the recovery. It didnt help any.Should i try to flash stock rom via odin? What should i do? It just wont get past the white screen. I repeat, flashing various ROMs didnt change anything.
Hello !
I rooted galaxy tab 3 T110 yesterday. Everything was correct until i tried to unroot. Now im stuck on teamwin blinking screen ( blue & purple ) HELP ME PLEASE ! Can i repair it or its already dead?
It working now
Hey !
I charged my tablet , and i go to dawnload mode . After that i put a new android same version as old 4.2.2 Jellybean and ev everythink works now .
Same Problem
I used CM12 flash, but after a factory reset from config the tablet started at TWRP with teamwin blinking.
I tried to reinstall TWRP from Odin, but not solve.
I changed TWRP for CWM under Odin and problem solved...
Hi Guys hoping someone can help me out.
One of my friends who should know better decided to try and flash a custom rom to his N7105 trouble is he used a n7100 twrp which apparently installed and then tried to flash a n7100 rom .
Now his phone is stuck in a boot loop, it sometimes gets as far as the animated boot logo with the blue led pulsing depending on what I last did to it lol. I can get into both download and recovery and the power button isn't stuck.
I don't know what stock version the phone was one when he started messing with it and he is vague about everything HE tried to do to fix it before I got my hands on it. Its entirely possible it was on 4.1.2 to start off with and he's tried to go straight to lollipop does the 7105 need to update in increments? or could he have put a n7100 bootloader on somehow but flashing stock via Odin should fix that right?
I have a memory of people having this sort of problem years ago with HTC and it ended up being a mismatch between the modem and baseband versions or something like that, thoughts?
Here's what I've tried
Odin flash CF-Auto root as it restores stock recovery at least now the PC detects it as t0lte not t03g
1) Recovery wipe data and cache - now only gets as far as the initial samsung galaxy note II screen
2) Odin flashing a 4.1.2 rom from sammobile - no go "unsupported" so has a knox bootloader
3) Odin flashing a 4.3 rom from sammobile - hangs on animated boot logo with the blue led pulsing
tried 1 again same result
4) Odin flashing a 4.4.2 rom from sammobile - hangs on animated boot logo with the blue led pulsing
tried 1 again same result
5) Install firmware via Kies - hangs on animated boot logo with the blue led pulsing
tried 1 again same result
Odin Flash proper version of twrp 2.8.7.0
6)Fix permissions in TWRP - says sucessfull but also has "E: unable to mount data" etc back to the initial galaxy note II screen
7) Flash custom rom via twrp - hangs on animated boot logo with the blue led pulsing
tried 1 again same result
I'm running out of ideas and patience with this thing does anyone have any other ideas for me to try?
After leaving the phone for a while to prevent me from smashing it into a million bits with the biggest hammer I could find I got it working tonight.
Charged the phone up I had to disconnect and reconnect a few times as it said it was 100% on the full screen battery picture then in recovery it said 18% or something
I re-flashed N7105XXUFNL2_N7105H3GFOD1_H3G from sammobile using Odin 1.85 along with the PIT file from this thread checking re-partition (I used a pit file otherwise I'd leave this alone), Auto Reboot, F.Reset time and Phone Bootloader update. This seemed to take longer than previous flashes.
Flashed TWRP 2.8.7.0
formatted Data in TWRP (the advanced one where you have to type yes to confirm). Previously Data was unmountable so I assume the long flash fixed something there.
Wiped cache in TWRP
and rebooted and waited ages and it came to life
Hello to y all
I have a LG G3 D855 running KK 4.4.2 rooted and I tried to install TWRP recovery with bump method
I don't know exactly where it goes wrong but I cannot boot in recovery even when I use an application to do it. I have a black screen with blue and red led light and I have to soft reset or pull my battery if I want to power up my phone.
I can normally boot my OS so I Guess it's only my recovery partition who have been messed up. Any idea?
PS: I thought it will be interesting to update to lollipop but i m a little confused about which file I should use.
I post a screenshot of my current configuration.
Thanks for your help.
Dont know if on 4.4 its like 6.x/5.x but when black screen with blue and red led light apear reload all steps and install mr.bump , exemple if im rooted on 6.0 and try to install another kernel after flash the kernel without exit twrp i must flash mr.bump!!! if i dont flash i get the same black screen with blue and red led light (not every kernel its a must to flash mr bump!! but to be sure every time i flashed)
Update to 5.0 first