Today I tried to root my AT&T (d2att) (SGH-i747) just upgraded to 4.3 yesterday. I am completley stock no root no custom recovery. I don't know what happened but it says "firmware upgrade encountered an issue. Please select recovery mode in kies & try again." I can't go into recovery,it won't let me. I ordered a jig (don't have it yet). It says this-
ODIN MODE
PRODUCT NAME: SGH-I747
CUSTOM BINARY DOWNLOAD: yes (5 counts)
CURRENT BINARY: Custom
SYSTEM STATUS: official
QUALCOMM SECUREBOOT: ENABLE
warranty bit: 0
BOOTLOADER RP SWREV: 2
So can somebody please help? I have download mode but recovery is a no go
bump please help phones been bricked for more than a day now
There is no Odin package for 4.3 OTA so you will have to install an Odin packaged custom recovery such as twrp then install a 4.3 ROM or higher via recovery. 4.4 KiKKat will work too.
Sent from my SAMSUNG-SGH-I747 using xda app-developers app
Hey guys I had a similar problem when I flashed a cf auto root file to the new ota. (sorry if that's a little noobish ) the way I fixed it was in kies being that stated above it's hard to get a Odin flash able 4.3 firmware. So I went into kies>tools>firmware upgrade/installation, (or something along those lines) a heads up you'll need your serial number and model number. Put all that in and it will tell you to put it into recovery mode (they really mean download mode not sure why they call it recovery) then plug it in and it'll download 4.3 and flash it to your device and voila! Not sure if it applies to you but it put my phone into safe mode. A reboot fixed that! I hope I helped you guys! Also another warning you will loose all your data.
Cheers!
hello, I bought this i747 in its current condition. I know nothing about its history.
when I power it on it goes to the phone, !, comp screen saying firmware upgrade encounter an issue, select recovery mode in kies.
in the top corner it says:
ODIN MODE
PRODUCT NAME: SGH-I747
CUSTOM BINARY DOWNLOAD: NO
CURRENT BINARY: SAMSUNG OFFICIAL
SYSTEM STATUS: CUSTOM
QUALCOMM SECUREBOOT: ENABLE
WARRANTY BITS: 0
BOOTLOADER RP SWREV: 2
Now when I connect to kies and run emergency firmware everything loads on kies, then gives an error, and
underneath BOOTLOADER RP SWREV: 2 it says: SW REV CHECK FAIL: Fused 2 > Binary 0 in red.
If this phone fixable? Any help would be appreciated.
mtsosie said:
hello, I bought this i747 in its current condition. I know nothing about its history.
when I power it on it goes to the phone, !, comp screen saying firmware upgrade encounter an issue, select recovery mode in kies.
in the top corner it says:
ODIN MODE
PRODUCT NAME: SGH-I747
CUSTOM BINARY DOWNLOAD: NO
CURRENT BINARY: SAMSUNG OFFICIAL
SYSTEM STATUS: CUSTOM
QUALCOMM SECUREBOOT: ENABLE
WARRANTY BITS: 0
BOOTLOADER RP SWREV: 2
Now when I connect to kies and run emergency firmware everything loads on kies, then gives an error, and
underneath BOOTLOADER RP SWREV: 2 it says: SW REV CHECK FAIL: Fused 2 > Binary 0 in red.
If this phone fixable? Any help would be appreciated.
Click to expand...
Click to collapse
Did you say it was recognized in Kies but firmware recovery failed? If so, and you were using Kies (not Kies 3), we may assume the last system update was not older than Android 4.1.1. I'll suggest you try these steps (in that order),i.e. if one doesn't work, try the next step ..
1. Try booting into recovery mode and doing a hard wipe/reset
2. Download the correct stock image from the thread below and flash via Odin. If you need help with flashing via Odin, please let me know
http://forum.xda-developers.com/showthread.php?t=1739426 or visit Sammobile.com to download the correct stock image.
3. Open Kies. Do not connect the phone yet. Go to Tools => Firmware Upgrade and Initialization. Enter your phone model name (SGH-I747)=>OK and serial number. Check device information inside the battery compartment. Wait for firmware download to complete and you are prompted to connect the phone and follow the rest of the on-screen instructions.
4. Contact the vendor to find out what they did wrong and see what refund options you have
Ok, so I also wasn't able to get into recovery.
I decided to flash cwm via odin. After it flashed the phone rebooted and turned on normally. I have turned it on and off like 5 times and everytime it boots normal.....But, there is still a problem... baseband version is Unknown and there is no IMEI Number.
Larry2999 said:
Did you say it was recognized in Kies but firmware recovery failed? If so, and you were using Kies (not Kies 3), we may assume the last system update was not older than Android 4.1.1. I'll suggest you try these steps (in that order),i.e. if one doesn't work, try the next step ..
1. Try booting into recovery mode and doing a hard wipe/reset
2. Download the correct stock image from the thread below and flash via Odin. If you need help with flashing via Odin, please let me know
http://forum.xda-developers.com/showthread.php?t=1739426 or visit Sammobile.com to download the correct stock image.
3. Open Kies. Do not connect the phone yet. Go to Tools => Firmware Upgrade and Initialization. Enter your phone model name (SGH-I747)=>OK and serial number. Check device information inside the battery compartment. Wait for firmware download to complete and you are prompted to connect the phone and follow the rest of the on-screen instructions.
4. Contact the vendor to find out what they did wrong and see what refund options you have
Click to expand...
Click to collapse
hi, yes those were the steps I tried and the result was fail. Now that I can boot it, it shows its 4.3 but no baseband and no imei.
mtsosie said:
hi, yes those were the steps I tried and the result was fail. Now that I can boot it, it shows its 4.3 but no baseband and no imei.
Click to expand...
Click to collapse
Oh, it's 4.3. Perhaps even better because you may be able to flash the 4.3 restore image. Your baseband/modem is corrupt or missing which is why it's showing the no baseband message.
Please see the thread below for the complete 4.3 stock restore image. Download the stock restore image and flash via custom recovery.
http://forum.xda-developers.com/showthread.php?t=2658486
Or you may just flash the 4.3 JB modem via custom recovery since you have custom recovery working. The modem zip can be found here ...
http://www.androidfilehost.com/?fid=23212708291681456
Larry2999 said:
Oh, it's 4.3. Perhaps even better because you may be able to flash the 4.3 restore image. Your baseband/modem is corrupt or missing which is why it's showing the no baseband message.
Please see the thread below for the complete 4.3 stock restore image. Download the stock restore image and flash via custom recovery.
http://forum.xda-developers.com/showthread.php?t=2658486
Or you may just flash the 4.3 JB modem via custom recovery since you have custom recovery working. The modem zip can be found here ...
http://www.androidfilehost.com/?fid=23212708291681456
Click to expand...
Click to collapse
:good: right on. you rock man. I flashed the modem and it works great now. thanks again.
mtsosie said:
:good: right on. you rock man. I flashed the modem and it works great now. thanks again.
Click to expand...
Click to collapse
You are most welcome. Glad to know it's now working.
hey guys am in trouble
Odin Refuse to flash
I747 warranty bit :1
bootloader rp swrev 2
SW rev check fail fused 2
Phone stuck on kies firmware upgrade encounterd
I Cant get 4.3 back again or downgrade to any older version
plz help me :'(
here is two screen shot in download mode while odin error
and in normal mode when i try 2 open
dark_darkness said:
hey guys am in trouble
Odin Refuse to flash
I747 warranty bit :1
bootloader rp swrev 2
SW rev check fail fused 2
Phone stuck on kies firmware upgrade encounterd
I Cant get 4.3 back again or downgrade to any older version
plz help me :'(
here is two screen shot in download mode while odin error
and in normal mode when i try 2 open
Click to expand...
Click to collapse
Can you try flashing custom recovery via Odin and then using custom recovery to do a stock restore to 4.3 following the instructions in the following thread ...
http://forum.xda-developers.com/showthread.php?t=2658486
can u share a link?
Larry2999 said:
Can you try flashing custom recovery via Odin and then using custom recovery to do a stock restore to 4.3 following the instructions in the following thread ...
http://forum.xda-developers.com/showthread.php?t=2658486
Click to expand...
Click to collapse
i've tried many custom roms
start flashing will and end with bug error at the end coz of warranty
can u share me a link for firmware tested ?
dark_darkness said:
i've tried many custom roms
start flashing will and end with bug error at the end coz of warranty
can u share me a link for firmware tested ?
Click to expand...
Click to collapse
I suggested custom recovery and not custom ROM. The idea is to get your phone back in working order first. Flashing a complete stock restore image should do it. Please refer to the thread I forwarded earlier. You should be able to flash custom recovery (like CWM or TWRP) to your phone via Odin and then use the custom recovery to flash the stock restore image.
This is what happened:
First I had Android 4.3 with KNOX
Then I flashed CyanogenMOD 11
I hated CyanogenMOD and tried to go back to stock firmware.
I downloaded the stock firmware from samfirmware.com and flashed with ODIN 3.09
Now i'm stuck on the Samsung Logo Boot Screen.
I have tried:
Reflashing
Using KIES emergency firmware recovery
Boot using safe mode.
Can you guys please help!?
Any error message in Odin? What is your current bootloader and which exact firmware are you trying to flash?
Androidwizzard said:
Any error message in Odin? What is your current bootloader and which exact firmware are you trying to flash?
Click to expand...
Click to collapse
CURRENT BINARY: Custom
SYSTEM STATUS: Official
KNOX WARRANTY VOID: 1
AP SWREV: A2
Trying to get stock Samsung firmware N7100UBUEMK4_N7100ZTOEMK3_ZTO
Odin does not shows error message...
RAFAMP said:
CURRENT BINARY: Custom
SYSTEM STATUS: Official
KNOX WARRANTY VOID: 1
AP SWREV: A2
Trying to get stock Samsung firmware N7100UBUEMK4_N7100ZTOEMK3_ZTO
Odin does not shows error message...
Click to expand...
Click to collapse
As your Knox counter says 1 I suppose you are trying to flash an older knox-enabled bootloader over a newer one.
Easiest way to succeed is to flash 4.4.2 firmware instead.
Whenever I was upgrading to a Kitkat custom Rom.
I faced Boot loop issues.
I upgraded my bootloader to DN3 V5 via ODIN but still the same bootloop issue.
I thought of restarting from scratch and while i connected my note2 via odin I used PIT_N7100_16GB_20121102.pit (pit file) and N7100XXDMG1_N7100ODDDMG1_INU_Prerooted in PDA file I am stuck in
"sboot.bin nand write start failed"...
Please help...
In download mode its showing
"Product Name: GT-N7100
"Current Binary: Samsung Official
System Status: Custom
Knox Warranty Void:1
AP SWREV: A2
SW REV. Check Fail. Device:2 Binary:1
Waiting for a wayout to start using my note2
Thanks a ton in advance...
If you've been 4.3 or 4.4 then you can not go back to 4.1.2. If more than bootlaoder MJ5 will not return
DMG1 is a 4.1.2 rom
sorry my english
net.susovan said:
Whenever I was upgrading to a Kitkat custom Rom.
I faced Boot loop issues.
I upgraded my bootloader to DN3 V5 via ODIN but still the same bootloop issue.
I thought of restarting from scratch and while i connected my note2 via odin I used PIT_N7100_16GB_20121102.pit (pit file) and N7100XXDMG1_N7100ODDDMG1_INU_Prerooted in PDA file I am stuck in
"sboot.bin nand write start failed"...
Please help...
In download mode its showing
"Product Name: GT-N7100
"Current Binary: Samsung Official
System Status: Custom
Knox Warranty Void:1
AP SWREV: A2
SW REV. Check Fail. Device:2 Binary:1
Waiting for a wayout to start using my note2
Thanks a ton in advance...
Click to expand...
Click to collapse
---------- Post added at 01:34 PM ---------- Previous post was at 01:30 PM ----------
Try other 4.4.2 rom. Ketain, DN3...etc .
Your warranty is over, because the knox varranty is 1.
mephike said:
If you've been 4.3 or 4.4 then you can not go back to 4.1.2. If more than bootlaoder MJ5 will not return
DMG1 is a 4.1.2 rom
sorry my english
Click to expand...
Click to collapse
need help
hello, i just downloaded the latest firmware NK2 link from the general thread, and run it thru Odin, and i unzip it. and Odin says PASS, but when turned it on my phone only stuck at the T-Mobile 4G LTE. whats wrong? what i need to do? help pls. thanks.
edit: i re do the odin, and now i got failed right away! now i cannot do the odin anymore. it gets failed right away. did i brick my phone? also if i turned it on it says
odin mode
product name : sgh-m919
current binary: samsung official
system status: custom
knox kernel lock: 0x0
knox warranty void: 0x0
csb-config-lsb: 0x30
write protection: enabl
eMMc: burst mode enabled
and it has a picture of phone yellow triangle with asterisk inside and computer
firmware upgrade encountered an issue. please select recovery mode in kies and try again.
pls help.
caloyzki said:
need help
hello, i just downloaded the latest firmware NK2 link from the general thread, and run it thru Odin, and i unzip it. and Odin says PASS, but when turned it on my phone only stuck at the T-Mobile 4G LTE. whats wrong? what i need to do? help pls. thanks.
edit: i re do the odin, and now i got failed right away! now i cannot do the odin anymore. it gets failed right away. did i brick my phone? also if i turned it on it says
odin mode
product name : sgh-m919
current binary: samsung official
system status: custom
knox kernel lock: 0x0
knox warranty void: 0x0
csb-config-lsb: 0x30
write protection: enabl
eMMc: burst mode enabled
and it has a picture of phone yellow triangle with asterisk inside and computer
firmware upgrade encountered an issue. please select recovery mode in kies and try again.
pls help.
Click to expand...
Click to collapse
update
after installing the firnware NK2, via odin, now im stuck at tmobile 4g lte logo. and i cant even access to my recovery to do wipe. pls help.
What happens when you try to access recovery?
caloyzki said:
update
after installing the firnware NK2, via odin, now im stuck at tmobile 4g lte logo. and i cant even access to my recovery to do wipe. pls help.
Click to expand...
Click to collapse
flash the root tar via odin somewhere in this forum or even on chainfires website. and then try rebooting. if not flash a custom recovery tar like philz and than i guarantee you will be able to boot into recovery and wipe your cache/ or flash a new rom