EDIT:
Most part of that problem solved, I bought new USB socket with ribbon, and replaced it. It worked. it seems there was a cold solder near the socket. USB works now with other devices like Flash drive, mouse, etc..
Still there's a little problem - while connected to a PC, neither phone nor PC show any signs of connection.
Anyone met the same problem? I checked on to computers Win8.1 and Win7 - no response.
I tried to install some additional drivers but with no luck...
------------------------------------------------------------------------------------------------------------------
< Old >
I've got Huawei P6 and used it with a few ROMs, after flashing one I noticed android doesn't detect USB connection anymore.
It sees it as regular charger - no popup on notofication bar, no way to exchange data with PC.
Changing ROM doesn't solve the problem. I tried stock ones with no effect (installed from zip file in TWRP).
I searched over the web and found no similar case. I think rolling back to full stock could possibly help, but I'm not sure how to do it - will creating dload folder with install data be enough? does it contain all the kernels, recovery and so on - to have the software version exacly as from factory?
USB OTG doesn't seen to work now either, It all worked before. Is there a way to force-detect the connection?
Please, don't write me to check the cable or drivers or to clean the USB plug. Each double... tripple checked. Tried different cables, computers. I've no problem connecting other phones.
I'll be very greatful for help in solving this issue. Even copying a photo to a pc is a problem now...
thanks in advance
Related
Hi, I have reflashed my ROM I dont know how many times. Yesterday I tried to connect via activesync on a new ROM and it wouldnt connect. These are some of the things that happened:
Device orange charging light flashes a few times then goes off [never seen THAT before]
Activesyc menu comes up on device but activesync doesnt connect
Get 'this device can perform faster' message on desktop
Sometimes get USB devce not recognized on desktop
SOmetimes device orange charging light it stays on if I plug direct into PC but still doesnt activesync
I have tried to connect as DISK DRIVE but I dont see the device on my PC.
Have tried different ROMS, 6.5, 6.51, sense 2.1 and 2.5 but all have same issue. Have also tried connecting to other computers. same issue.
Have played around with USB to PC menu options (enable / diable faster data sync etc) but doesnt make a difference.
Anyone had this problems? Thoughts?
Have you tried diselecting "ask me 1st about usb connection type when I connect the device to the pc" under USB to PC settings
It worked for me
This is the exact problem I am facing!
I tried everything - as diskdrive, activesync (with/without speedup), etc.
On many ROMs, even the original one (WM6.1)
Can't connect - every PC gives an 'unknown device' and on some ROMs I cannot charge via USB, only via mains...
I also tried without the question on connection.
Just some thoughts:
Do you have corruptions on screen sometimes? (Some graphical glitches)
Any .CAB files you cannot install?
Did you try to reflash the same ROM more than once?
tried to connect without card in the device and in flight mode? (Uses less power)
With me it started after a ROM flash from Miri... (I don't blame him!!)
The Hard SPL did not give me any problem, the radio was not flashed, just the OS. But reverting did not help.
I certainly hope you will find a solution, since I have the exact same problem!!
Do you stil know what ROM you flashed when this problem occured?
I reverted to original ROM 6.1 AND 6.5 which included everything - boot, radio, os, stardup image. But it did not change!
I figured it out after trying everything i could: i think its a hardware problem. I have dropped my devicetoo many times, or plugged it in too many times. Who knows.
ekerbuddyeker said:
I figured it out after trying everything i could: i think its a hardware problem. I have dropped my devicetoo many times, or plugged it in too many times. Who knows.
Click to expand...
Click to collapse
And how did you figured it out? Did you return the device to the shop?
I have this exact same issue except I am on AthineOS... I thought it was my PC until I read these posts. No OS updates or any other machine updates were performed except on my device. Any clues as to a fix?
Somehow I don't think this is just hardware.
I did drop my device once, but that was even before first flash. After that it still worked.
So, some weeks later I HSPLed without any problem. After that the device still worked.
Then, after investigating which ROM to use I flashed the ROM a few days later.
Right after the first flash it all still worked. So, had to flash another and from that moment on the device cannot be reckognised by any PC.
I still think it has something to do with the flashing. I think the device does not give correct feedback when it receives some commands from PC (eg. the command to reply the device type/number)
Does anyone know a program which can check the USB port for the HTC Touch Pro 2? Just to test wheather the connector pins are ok?
download activesync 4.5 and run the setup. it will perform a repair. that usually solves the problem. if not, try a different usb cable and try plugging into different ports on your pc.
crazythunder said:
download activesync 4.5 and run the setup. it will perform a repair. that usually solves the problem. if not, try a different usb cable and try plugging into different ports on your pc.
Click to expand...
Click to collapse
These are the first things done. And this was already written in here.
It happens with many PCs, including some on which the device never connected to.
Also tried different cables, ports, etc.
Also disabled the fast transfer etc. etc.
Even tried several other ROMs, inclusding original Dutch 6.1 and Dutch 6.5
I'm having the same issue. I can connect via bluetooth, but not usb. And I'm stuck with 6.1. I was tole my phone was brand new, but now I'm starting to think otherwise.
waynehead05 said:
I'm having the same issue. I can connect via bluetooth, but not usb. And I'm stuck with 6.1. I was tole my phone was brand new, but now I'm starting to think otherwise.
Click to expand...
Click to collapse
Some questions, to verify this is due to flashing or is a fault in the design of the device...
- Where did you get the device?
- Have you flashed the device?
- Did you accidentally drop the device?
hi just to say had a completely orignal o2 xda orbit 1 flashed with new rom everything worked perfect before now active sync plays up i can sometimes connect but get usb device not reconigsed then click cross then pull out usb then reinsert then active sync connects works fully functional then after 5 min it disconects this is driving me mad as use active sync for a fast internet connection on my pda as my wifi is crap
I was trying to put the hum/hiss sound fix on my sd card and I cannot get my pc to connect via USB...
My wife has a TP2 and it connects fine...
I have tried with/without the sd card in, rebooted the pc and phone, rebooted the phone while connected to the pc.... nothing...
wtf...
anyone else with this problem?
PS... NRGZ28 had posted a very basic rom for booting to android back in Feb and it is now gone from hotfile. Anyone know of a quick boot into android?
- Try a different computer
- Try a hard reset
That are the first thing you should do.
Tried hard reset...
Dif PC is not an option at the moment... I have rebooted...
Just flashed the ROM (NRGZ newest, thank goodness I had it on my SD card) and I still cant get it to sync...
I have attached the USB error I am getting... (Win7, new install)
The phone is not asking if I want to active sync or use as storage???? wtf...
FarBeyond said:
Just flashed the ROM (NRGZ newest, thank goodness I had it on my SD card) and I still cant get it to sync...
I have attached the USB error I am getting... (Win7, new install)
The phone is not asking if I want to active sync or use as storage???? wtf...
Click to expand...
Click to collapse
Reboot your PC? lol bet your tried that already...
Try this:
settings > connections > usb to pc > and disable Faster Data Sync then try. This way uses the generic usb drivers and maybe it will connect.
That did not work...
How do I get my Win7 laptop to see the phone with Android on it?
FarBeyond said:
That did not work...
How do I get my Win7 laptop to see the phone with Android on it?
Click to expand...
Click to collapse
dont think thats working yet
Ya I don't think that works yet, it's tied to Android software drivers and the use of the USB port, since there is no drivers to control the port only to charge battery. Windows thinks there is something there, but the phones USB can't communicate back....I think this is the issue or at lease after playing around with it on my phone anyway
Not that it's a huge amount of help but might troubleshoot down to the hardware level...if you go into bootloader mode on the phone and connect to USB does it connect?
I don't think you should go that deep and dirty. My touch pro 2 works only with only 1 (non-HTC) cable of the 10 i have at home, all are the "standard" mini-USB but only one works flawlessly for communicating/flashing/syncing, the other cables either do the same error - device not recognized - or windows says that the device could communicate faster - and only copies files slowly.
All in all: you should simply check with another USB cable or if you have the factory HTC cable try it with that. I noticed that the cable i am using other than the HTC one is a very good quality thick (low-resistance and double-shielded) USB cable and it never failed on me.
One other thing you should definitely watch for: plug the USB cable into the motherboard USB port directly (on the back of the PC where you plug the keyboard, mouse etc.), sometimes PC cases with front panel USB outputs simply die, or are wrongly attached to the motherboard USB header and it can cause the aforementioned problems too, not to mention if it is wrongly attached it could harm your phone too.
I've searched and search and found nothing, so I need a little help with this one.
On my computer I run portable apps from a flash drive. I also like to connect my Android phone. The problem I have is that while either one works swell by itself, the computer fails to recognize one or the other when both are plugged in at the same time. Preference is always given to the device that is plugged in first.
As I'm always using my flash drive, it's a hassle to disconnect it just to plug in my phone. And it's even more irritating to know that I can't access my portable apps as long as my phone is connected. The best I can do so far is to plug the phone in and choose charge only which allows XP to see it as an Android ADB device. This assigns drive letters to the multiple drives android uses, but all drives are listed as being empty. I should also note that I do have a printer connected via USB but I never have any problems with it.
What I've tried to fix the problem:
-Utilize the USB ports in the rear of the computer - No Luck
-Manually assigning drive letters - No Luck
-Search for alternative driver for Flash Drive - No Luck
-Downloaded HTC SYNC for an alternative driver to my phone - No Luck
-Downloaded and "Unsuccessfully" attempted to install Android SDK USB driver. - I don't know if this would have solved the problem or not but the installation of SDK never seems to give me the driver the phone is looking for.
So I'm at a loss as to whether or not there is a fix to my problem. Any help would be appreciated!
Computer - XP SP3 / Pent 4
FlashDrive - 8Gig Corsair Voyager
Phone: Rooted HTC Incredible running Synergy RC1 ( I throw this in there just for an FYI but the problem was present on other ROMS I've tried so I'm not led to believe it's a Rom issue)
I'm not sure if this is a Phone issue, or a computer issue so I've cross posted this with the folks over at Tech Guy Support
MOD - Problem Solved please feel free to delete if you don't think it's useful to keep this around.
Problem was solved (Credit to Rockn over at Tech Guy Support). My PC is underpowered to run my USB devices. I plugged the phone into a Powered USB Hub and it works perfectly now.
i have posted my problem earlier in this thread below and havent get solution yet
http://forum.xda-developers.com/galaxy-note-8-0/help/note8-null-imei-unknown-baseband-sim-t3158071
my device is
Samsung galaxy note 8 inch GT-N5100 android version 4.4.2 baseband unknown kernel 3.0.31-2637964 [email protected]#1
Version number KOT49H.N5100XXDNH3 IMEI NULL.
my problem is
- i can't connect my note to computer, when i connect the handheld the battery shows red X cross and it wouldnt detect neither wont charging.
- but when the device charged via ac adapter it work fine.
- the device wont recognice sim celluler card "mobile network not available"
nb: all feature and function works fine inclde wifi, bluetooth, etc. (the error just gsm function and connection usb mode with PC)
i have tried this some work but couldnt solved my problem yet.
- i cant rooted my device via odin caused by the device won't detect any usb to my pc. (normal mode or download mode)
- i tried to restore efs by efspro software but not working caused by the device won't detect any usb to my pc.
- i tried to rooted via cfautoroot apk not working either
http://forum.xda-developers.com/showthread.php?t=2291839
- i have replaced the Micro USB charging port receptacle and it just the same, i think the hardware of my usb port is fine.
https://www.youtube.com/watch?v=nvpNliFIuN4
what i havent try is restoring my efs file with flasher tools like octoplus box. because i dong have that tools. and i think its too expensive to solving my problem of one device with buying flashing tools investment.
http://forum.gsmhosting.com/vbb/f453/galaxy-note-8-n5100-efs-problem-1829891/
is there any other solution, or direction which reference should i read, or maybe who should i pm that maybe he has the same problem and solved the day before.
apreciated any help, response, and view. thnks. -Fardha-
fardha said:
i have posted my problem earlier in this thread below and havent get solution yet
http://forum.xda-developers.com/galaxy-note-8-0/help/note8-null-imei-unknown-baseband-sim-t3158071
my device is
Samsung galaxy note 8 inch GT-N5100 android version 4.4.2 baseband unknown kernel 3.0.31-2637964 [email protected]#1
Version number KOT49H.N5100XXDNH3 IMEI NULL.
my problem is
- i can't connect my note to computer, when i connect the handheld the battery shows red X cross and it wouldnt detect neither wont charging.
- but when the device charged via ac adapter it work fine.
- the device wont recognice sim celluler card "mobile network not available"
nb: all feature and function works fine inclde wifi, bluetooth, etc. (the error just gsm function and connection usb mode with PC)
i have tried this some work but couldnt solved my problem yet.
- i cant rooted my device via odin caused by the device won't detect any usb to my pc. (normal mode or download mode)
- i tried to restore efs by efspro software but not working caused by the device won't detect any usb to my pc.
- i tried to rooted via cfautoroot apk not working either
http://forum.xda-developers.com/showthread.php?t=2291839
- i have replaced the Micro USB charging port receptacle and it just the same, i think the hardware of my usb port is fine.
https://www.youtube.com/watch?v=nvpNliFIuN4
what i havent try is restoring my efs file with flasher tools like octoplus box. because i dong have that tools. and i think its too expensive to solving my problem of one device with buying flashing tools investment.
http://forum.gsmhosting.com/vbb/f453/galaxy-note-8-n5100-efs-problem-1829891/
is there any other solution, or direction which reference should i read, or maybe who should i pm that maybe he has the same problem and solved the day before.
apreciated any help, response, and view. thnks. -Fardha-
Click to expand...
Click to collapse
Are you using two different cables in testing or are you just moving the charging cable from the adapter? I found uninstalling the windows usb driver and rebooting to reinstall may help detect the device. Some usb ports dont have 500ma output for charging or change to a different port if available. Changing the connection type on the usb status icon to reset and set the type of connection may trigger the usb driver to connect. I think for the most part your windows driver is failing to initiaize and detect your device. Trouble is getting it to reset cleanly and install properly.
Once the device becomes detected, you can perform the steps to restore your device in order to use a sim card.
gooberdude said:
Are you using two different cables in testing or are you just moving the charging cable from the adapter? I found uninstalling the windows usb driver and rebooting to reinstall may help detect the device. Some usb ports dont have 500ma output for charging or change to a different port if available. Changing the connection type on the usb status icon to reset and set the type of connection may trigger the usb driver to connect. I think for the most part your windows driver is failing to initiaize and detect your device. Trouble is getting it to reset cleanly and install properly.
Once the device becomes detected, you can perform the steps to restore your device in order to use a sim card.
Click to expand...
Click to collapse
Thanks for your response,
About the cable is fine to apply for any gadget, but won't work on my Galaxy Note. I have repaired it at unofficial service center and they said there is no problem with the cable nor the usb port
And still, they don't know yet where the trouble is.
is there any possibilities to fix my Galaxy Note in this case? Thank You
Hello folks
since hours i have been troubling with an issue with my HTC 10.
Everything started yesterday, as my phone showed me a notice that the battery is loading slowly and I should use the original cable for faster charging (what I was doing) [ERROR 1]. Afterwards, I wanted to make a backup on my computer for flashing, but the usb connection was instantly lost [ ERROR 2]. So I backed up on SD.
I decided to do a RUU in hope that this would fix it. The problems stayed.
The USB Connection in download mode faces the same issue. Phone is recognized and a few seconds later the connection is lost. Only charging works.
Some ideas what I did and tried out:
- USB Debugging
- Use As External Storage
- USB Network Settings)
- Reinstalled drivers (different ones, e. g. Universal ADB Drivers)
- installed and reinstalled HTC sync
- tried different USB ports
- changed the energy options of USB ports
- try an other usb cable
- cleaning plugs
- wiping cache
- ruu
- other firmware / other kernel....
Additionally, I tested it on four different computers and laptops with the difference, that on those the phone is not being recognized at all; no entries in the device managers. (charging works)
Now I am quite out of ideas where the problem could be?! Might it be a hardware issue? What else could it be?
Hope anybody can help....
Thanks....