Develop Bugs

[Q] Stuck on Kindle Fire Logo Screen with no ADB

OK, folks. Hopefully somebody can help me out of this mess I've caused. I'm currently stuck on the Kindle Fire Screen with no access to ADB to get into fastboot or anything else.
Here's how I got there:
Fire was rooted and had CWM recovery installed using KFU
Downloaded Pure AOKP ICS ROM with 3.0 kernel
Flashed with CWM like an idiot, instead of using TWRP like the instructions called for
Here I am -- My Kindle shows up in Windows 7 Device Manager, but can not be found via ADB; it just hangs on the Kindle Fire boot screen.
I've done a lot of reading on the subject and I'm really hoping I won't have to resort to getting a factory cable.
Any help would be greatly appreciated, folks!

The only thing I can think of atm is either the KFU or the kindle fire unbrick utility. Try both.. good luck..

Sounds like you are not bricked and fast boot is possible.
I would recommend trying to fast boot twrp onto it and get into recovery.

Stuck at "kindlefire" bootlogo

Hi,
currently I am stuck at the non flashing "kindlefire" bootlogo.
I cant access TWRP anymore and my computer also does not recognize the kindle fire.. what options do I have to get a bootable kindle fire again?
What I have done in the last 4 hours to end up in that state:
follow this thread: http://forum.xda-developers.com/showthread.php?t=2105077
IMPORTANT: WHEN COMING FROM STOCK AMAZON OS
-Make sure you wipe everything while in TWRP before you flash anything!
Click to expand...
Click to collapse
I did like statet and ended up without OS because I wiped everything like statet.
Then, after booting into fastboot I tried that tool:
http://forum.xda-developers.com/showthread.php?t=2096888
It said that I recovered my kindle to stick firmware but In fact I am stuck now with the bootscreen.
Can anyone help me please?
after following this thread

Do you have a KF1 or KF2?

As soup said, are you sure you have a Kindle Fire 2?
Did you buy it new, and did it come in a brown or black box?
You might be OK to flash TWRP again, then use ADB push command to get a 10.1 ROM onto your Kindle. I would talk with Soup a bit in case there is an issue with his tool.
Sent from my Amazon Kindle Fire2 using Tapatalk HD

[Q] My kindle fire is stuck at logo

I need some help with this I rooted my first gen kindle fire with the kindle fire utility v0.9.6found on this website. Everything went successful I installed superuser, firefirefire and a new rom. I dodn't like it so I downloaded the stock update from amazon and tried to install it using twrp but it said that it filed and when I tried to reboot it it said it had no OS installed. I can make the kindle appear on computer but I can't open it only right-click it. I've tried installing twrp manually but I always get stuck at waiting for device. When the Kindle reboots reconnects and disconnects and then reconnects. But all I see is the kindle fire logo. It can sit there for hours and it doesn't do anything.I've tried KindleUnbrick Utility V0.1 V 1.0 and V1.1 But those don't work because they say the device was offline even it actually wasn't. Iv tried everything unless someone has an idea.

[Q] need help with boot loop

Please forgive my noob-ness. I've done some research but i can't figure out whats up with this device.
I have a Kindle Fire first gen that is stuck in a boot loop. I get the boot logo with "Kindle Fire" and a flicker effect but that is it. This is NOT my device i'm trying to fix it for a non-technical family member. I know they didn't try to root it or any of that. It just stopped working for them one day.
after installing / removing / reinstalling the drivers a million times i finally got the kindle fire utility to see the device as online. its seems like no matter what i do the device goes back to the boot loop and KFU gives me "waiting for device'. anyone have any ideas? do i need the factor cable to get this working again??

according to FAQ 16 Frequently Asked Questions - Amazon Kindle Fire
If the Kindle Fire logo you're talking about flashes and goes dim after being brightly lit for a few seconds, then your device is trying to boot normally to a malfunctioning operating system, likely caused by not wiping the data partition (factory reset) before flashing a ROM. If that's the case, you will likely need a factory cable to get into fastboot mode so you can access or (if needed) install custom recovery, then reinstall a ROM properly.
Click to expand...
Click to collapse
yes you need a fastboot cable
or
there is a [UTILITY] Kindle Fire Unbrick Utility V1.1! that you can try

kfs325 said:
Please forgive my noob-ness. I've done some research but i can't figure out whats up with this device.
I have a Kindle Fire first gen that is stuck in a boot loop. I get the boot logo with "Kindle Fire" and a flicker effect but that is it. This is NOT my device i'm trying to fix it for a non-technical family member. I know they didn't try to root it or any of that. It just stopped working for them one day.
after installing / removing / reinstalling the drivers a million times i finally got the kindle fire utility to see the device as online. its seems like no matter what i do the device goes back to the boot loop and KFU gives me "waiting for device'. anyone have any ideas? do i need the factor cable to get this working again??
Click to expand...
Click to collapse
Not sure of the state of your Kindle Fire G1 (It's not rooted? Are you sure?), but this sounds similar to what I ran into trying to install CM11.
What version of TWRP do you have installed? If it's 2.2.2.1 and you're trying to install a ROM with KitKat (CM11) you can run into this. I did. When I installed TWRP 2.7.0.1 I could install CM11 just fine without the boot loop.
To install TWRP 2.7.0.1 I found that you could only do so by:
When you turn Kindle Fire on, hold down the power button to cycle through the options when you see the Kindle Fire logo. You want to land on the Recovery option.
Mount storage from TWRP 2.2.2.1 on a PC and copy CM10.x.x and related GApps to SDCARD
Factory reset then reinstall CM10.x.x (with Gapps for that version)
Install Flashify from the PlayStore
Download the latest TWRP for otter/Kindle Fire G1 (2.7.0.1)
Install it with Flashify
Download CM11 and related ZIPs (GApps kk, Change to Nexus 7, etc) to Downloads directory
Restart into TWRP recovery (should be 2.7.0.1 now), and factory reset/reinstall CM11 and related ZIPs from Downloads directory
Should be fine now.
I found that I could only do it this way because for some reason Kindle Fire Utility Kit and ADB couldn't work with my Kindle anymore with TWRP 2.2.2.1 (don't ask, I don't know why). This way works. Just make sure you have a copy of a version of a ROM and GApps on SDCARD at all times since mounting storage might not work anymore in TWRP (again, I'm not sure why). I tried it again and again, but I couldn't get it to work and it might be the same for you. Keep in mind this is for CM11. If you're using stock, then follow sd_shadow's advice.

bricked fire stick 1st gen

hi, i accidentally bricked my fire stick 1st gen (montoya) by flashing magisk. i had twrp recovery before and was stupid enough to flash magisk without knowing it would brick my fire stick. it only boots up to the white amazon logo. i am able to send fastboot commands but it says the bootloader is locked when i try to flash the boot and recovery.
is there anything i can do? i tried searching but i could only find the 2nd gen bootloader unlock.