Related
i had notice there is alot similar post to this problem but none really solved it. so i start this thread to make it more specific
1) once connected to pc, my wildfire automatically charge
2) no pop-up or option on the top to slide down to select either htc sync, mount as sd card, etc
3) tried reboot, mount unmount card, untick usd debugging, changed other rom, but still not working.
4) if connected to pc still automatically charging even if i change "default connection type" to disk drive, or usb tethering
5) i tick "ask me" so i can choose the connection type when connect to pc, but when connected to pc, nothing. just charging.
i'm rooted, using hg hybrid v3 (problem was there before i flash HG rom). it used to work before. i dont recalled when was the last time it start to behave like this. all this time i thought i set the connection default to charging, but when i want to transfer songs, only then i realised this problem. i m not sure which custom rom might cause this problem (if it does) because i had flash more than 10 roms
i have same problem with cm7
I haven't try to format my sd card. because when I connect without sd card, still no connect option. if my card is malfunction/the main problem, then my phone should work fine n show the connect option after I remove the card, right? (I do have connection option on the setting. what I meant no connection option is the pop up conection menu+connection option on the top bar. changing the connection on the setting change nothing)
I too have this prob but never questioned this as i never use htc sync. But if u really wanna use it try this i'm not sure it may work or not but mostly its due to driver problem:
1.Connect your device in htc sync mode.
2.Uninstall or Remove all drivers of htc and also htc sync.
3.Disconnect your device and Restart your pc.
4.Reinstall htc sync and connect your device in htc sync mode.
5.It'll install fresh drivers for your device and if asked to restart then do it else run htc sync.
If you are running vista or later try to run htc sync in administrator mode.
I'm not sure this method work but there's no problem on trying it. Reply your result after doin above steps
I also think the problem might related to my driver but I remember that when I first connect to my pc, there will be pop up menu, and my phone automatically recognized as "disk drive" (I m not install HTC driver yet. infact ,I install the driver after my phone connected to my pc through disk drive connection since the driver located on the SD card). nway, I"ll try your method and post the result later.
I just notice this might not work..the problem is I cannot change the connection. even if I did, it doesn't change the connection. it just charging.. as if I put it on default "charging" as it connect. but I will try later anyway
When i connect my phone the debugging icon shows up and my pc makes the noise but doesnt let me choose mass storage (running cm7). it shows up on my pc on drive f: but when i click it just says please insert a disc into removable storage F:
xynok, did u tried untick the usb debugging? go to setting, application, development, untick usb debugging. u still lucky at least it prompt u something if u connect to pc, mine nothing. its like I plug it to the socket wall not pc
anakhanjing said:
xynok, did u tried untick the usb debugging? go to setting, application, development, untick usb debugging. u still lucky at least it prompt u something if u connect to pc, mine nothing. its like I plug it to the socket wall not pc
Click to expand...
Click to collapse
yeah i tried that
lokeshramesh said:
I too have this prob but never questioned this as i never use htc sync. But if u really wanna use it try this i'm not sure it may work or not but mostly its due to driver problem:
1.Connect your device in htc sync mode.
2.Uninstall or Remove all drivers of htc and also htc sync.
3.Disconnect your device and Restart your pc.
4.Reinstall htc sync and connect your device in htc sync mode.
5.It'll install fresh drivers for your device and if asked to restart then do it else run htc sync.
If you are running vista or later try to run htc sync in administrator mode.
I'm not sure this method work but there's no problem on trying it. Reply your result after doin above steps
Click to expand...
Click to collapse
not working..
try this if u r using sense roms . Also try this for AOSP roms, if there is an option(i dont know about AOSP).
Go to Settings/Applications/Manage applications/All/
Then search for "Connect to PC". Actually in stock roms that was an app by htc. But there must be something similar to that in AOSP roms. Then open that and select, "Force stop" , "Clear data", "Clear cache".
I dont know for sure if that solves the issue or not. But have a try.
And by seeing this thread, actually i got a doubt, "can we synchronise the htc sync in AOSP custom roms". Since AOSP is nothing but removing the HTC crap. Can someone confirm this .......
bharatgaddameedi said:
try this if u r using sense roms . Also try this for AOSP roms, if there is an option(i dont know about AOSP).
Go to Settings/Applications/Manage applications/All/
Then search for "Connect to PC". Actually in stock roms that was an app by htc. But there must be something similar to that in AOSP roms. Then open that and select, "Force stop" , "Clear data", "Clear cache".
I dont know for sure if that solves the issue or not. But have a try.
And by seeing this thread, actually i got a doubt, "can we synchronise the htc sync in AOSP custom roms". Since AOSP is nothing but removing the HTC crap. Can someone confirm this .......
Click to expand...
Click to collapse
nope. still nothing. anyway since it had this problem, I had wipe my wildfire few times, n try different rom.. maybe it is because of faulty cable. but if the cable is the culprit, why it still charging? is it possible the cable is broken but still can charging?
anakhanjing said:
nope. still nothing. anyway since it had this problem, I had wipe my wildfire few times, n try different rom.. maybe it is because of faulty cable. but if the cable is the culprit, why it still charging? is it possible the cable is broken but still can charging?
Click to expand...
Click to collapse
Not telling that it should be, but definitely there is a possibility of a cable culprit.
The USB male/female end has 4 connections in which two connections are used for voltage and the remaining two connections are used for data transfer.
There might be a possibility that the data connection got broken with voltage connection retaining. Try with another cable (any USB v2 cable).
And one more thing, for having the disk drive option, nothing need to be installed in the pc. U need to install htc driver in the pc only if u want to use usb debugging , usb tethering.
[But at the wildfire end the cable has 5 connections and i dont know what the 5th one is for. mostly it will be a NO CONNECTION]
Now i got another idea to diagnose ur issue.
Well do u know of application "pdanet". It uses USB DEBUGGING feature to tether ur phone internet to PC. Actually usb debugging can be used both under charge mode and disk drive mode. What u can know on doing this is whether usb debugging through ur phone is working or not. U can diagnose the thing while checking with every app that uses usb debugging. So try it. Enable the usb debugging in phone first.
---Install pdanet desktop version and follow the setup instructions. It asks to connect ur phone during setup to install usb driver and also pdanet.apk to mobile. Connect ur phone with usb debugging enabled. I doubt whether desktop version installs or not because of ur issue. Mostly desktop version of pdanet will not install without a phone connected having usb debugging enabled. And if the desktop version is installed successfully, that means ur phone usb debugging is working. And if desktop version is installed successfully, that means it also installed the mobile version of pdanet.apk to ur phone (which says that data transfer is working). Then open the pdanet on phone and enable usb tether. Then open pdanet from desktop and connect. Then see whether u r able to access internet from pc.
---One more method is try to use ADB from android sdk. It also uses the usb debugging feature.
If adb and pdanet works, that means usb debugging feature on ur phone is working. If it is so, then it is mostly not a cable problem (as far as i know). And if they dont work there is a chance that it is a cable problem.
......................................................................................................................................................................................
And one more thing. If u have used a stock rom (freshly formatted), and faced the issue, then it is mostly not a software problem. Then it might be cable problem or some kind of problem in ur phone. Also check ur phone radio version. Thats all.
bharatgaddameedi, i cant install pdanet. it say android phone not detected. error =103. i think u were right. its hardware related problem but its look like not the cable. most probably its my wildfire usb jack. i test the cable with other mobile, its working (test it on nokia 5800). before i had this problem, sometime i use htc cable to transfer data for my 5800, and some time i used 5800 cable to transfer data for my wildfire. the difference between the two cable pin might damage my wildfire usb jack.. (u said htc cable got 5 pin, so i asume nokia got 4?)
anakhanjing said:
bharatgaddameedi, i cant install pdanet. it say android phone not detected. error =103. i think u were right. its hardware related problem but its look like not the cable. most probably its my wildfire usb jack. i test the cable with other mobile, its working (test it on nokia 5800). before i had this problem, sometime i use htc cable to transfer data for my 5800, and some time i used 5800 cable to transfer data for my wildfire. the difference between the two cable pin might damage my wildfire usb jack.. (u said htc cable got 5 pin, so i asume nokia got 4?)
Click to expand...
Click to collapse
So, pdanet not detecting the phone means usb debugging is also not working under charge mode. That should be phone hardware related problem like u have said about usb jack.
And No. All the micro USB version 2 cables will be the same. Its same for 5800 and wildfire. I use my previous 5233 cable to my wildfire even now.
The usb jack of wildfire may damage if u have used it in an improper way. Something like pressure on the cable when connected and so on...
So, its not something we can solve here. That should be given to service centre as far as i know
anakhanjing said:
the difference between the two cable pin might damage my wildfire usb jack.. (u said htc cable got 5 pin, so i asume nokia got 4?)
Click to expand...
Click to collapse
Can't be. I am using my N82's data cable for data transfers on my Wildfire from Day 1. The provided data cable is pretty much permanently attached to the wall charger.
I accept the fact that it might be hardware problem but there is one more thing I want to try. how about flashing stock rom from pc? flashing 2.1 is ok since it can be rooted again. I had flash stock rom but from the clockwork mod, not from pc, and the hboot is been remove for save flashing. I never try this before because all this time I thought that the problem was cause by custom rom, so I just need to find the right custom Rom.
How can u flash a stock Rom from pc when the usb is not functioning. RUU will not work.
Things get worse when basic things stop functioning.
Sent from my HTC Wildfire using XDA App
Did you try mounting your SD Card via Recovery? Reboot into Recovery > Advanced > Mount SDCard
Hello,
I've a big issue, if I try to connect the phone, via usb, to the pc windows none of the devices recognize the connection.
Nothing appear on the Defy. On the Pc, sometimes appear the "new device windows" but if I try to install drivers it show me an alert saying that the device is not installed correctly.
I've tried all the motorola drivers available but nothing happen. I've also tried 2 other pc and 2 other usb cable
Fortunally, the device is rooted and I can install a nandroid backup but I don't know how I can resolve this issue, someone can help me?
Thanks
nickee said:
Hello,
I've a big issue, if I try to connect the phone, via usb, to the pc windows none of the devices recognize the connection.
Nothing appear on the Defy. On the Pc, sometimes appear the "new device windows" but if I try to install drivers it show me an alert saying that the device is not installed correctly.
I've tried all the motorola drivers available but nothing happen. I've also tried 2 other pc and 2 other usb cable
Fortunally, the device is rooted and I can install a nandroid backup but I don't know how I can resolve this issue, someone can help me?
Thanks
Click to expand...
Click to collapse
Enable / disable USB debugging maybe? But normally there should be a prompt on the phone when you plug it in (pulling down the status bar usually asks you what to do, give memory card access, charge only...). Btw, does the Defy charge when plugged in or does the LED light up?
Arjoma said:
Enable / disable USB debugging maybe? But normally there should be a prompt on the phone when you plug it in (pulling down the status bar usually asks you what to do, give memory card access, charge only...). Btw, does the Defy charge when plugged in or does the LED light up?
Click to expand...
Click to collapse
Tried but nothing change. The phone doesn't charge correctly and no prompt message if I connect it to the pc.
And it is definitely not the cable and / or the USB port? Then it has to be a hardware problem on the phone's side I think.
Arjoma said:
And it is definitely not the cable and / or the USB port? Then it has to be a hardware problem on the phone's side I think.
Click to expand...
Click to collapse
Not the cable and not the USB
There's a way to reinstall all the Defy driver without the cable?
Try installing new moto drivers.
http://forum.xda-developers.com/showthread.php?t=1100585&highlight=rsd
Installed but no improvement on the situation. I think that's an hardware problem...
nickee said:
Installed but no improvement on the situation. I think that's an hardware problem...
Click to expand...
Click to collapse
Almost seems so : But charging works?
Arjoma said:
Almost seems so : But charging works?
Click to expand...
Click to collapse
Charging didn't work if I connect the phone to the pc, it's strange because if I connect to the electrical power it works.
I also think that I've had an issue when I've installed the custom firmware
Hi all ! I am new here (sorry for my english by the way)
I tried to find something about my problem on many forums but I can't find anything ! I tought hère was the best place to find an answer to my question
I have an HTC one m8 with the Skydragon Lollipop ! I have this since like 2 months... My charging dock was perfect, but since abouth a month, I can charge my phone, but if I plug my HTC in the computer, the computer don't see it... The only way to sync things in my cellphone is to put my phone on Recovery mode !!
Do you know why ? Is there a way to fix this ?
Thanks
Try revoking the USB debugging authorizations* and accepting it again when the PC asked. Make sure the drivers are up to date as well(On the PC) , you might also want to try the generic drivers for Android device. Uninstall HTC drivers and HTC Sync, go to device manager and select Android MTP drivers. You could also try a different port, maybe it's a USB 3.0 issue, try a different cable if you have one(just in case).
* You can revoke USB debugging authorizations inside the developer options.
If you can access device through recovery then it can't necessarily be a usb port issue, seeing as it sees it there.
BerndM14 said:
Try revoking the USB debugging authorizations* and accepting it again when the PC asked. Make sure the drivers are up to date as well(On the PC) , you might also want to try the generic drivers for Android device. Uninstall HTC drivers and HTC Sync, go to device manager and select Android MTP drivers. You could also try a different port, maybe it's a USB 3.0 issue, try a different cable if you have one(just in case).
* You can revoke USB debugging authorizations inside the developer options.
If you can access device through recovery then it can't necessarily be a usb port issue, seeing as it sees it there.
Click to expand...
Click to collapse
When I am in recovery I can access my things with Android File Transfer, but not with HTC sync manager.. Forgot to tell you that I have a Mac I dont know if it change something except that there's only 3.0 usb ports !! ( about a month ago I was able to transfer things with HTC sync manager though !!
I tried revoking the USB debigging and acceptant them again but it still not working :/ Also tried to reinstall HTC sync manager but it's not working neither ! Also tried different USB cables, but nothing to do with that neither !!
Thank you so much for the help !!
When I Try to connect My Zenfone to PC & also trying to connect on debugging mode then it show display that debugging section is totally disabled & showing message "Device is in Charging mode, USB debugging is disabled.
&
2nd Problem is Media Device Not showing in Mobile & PC Also.
PLZ HELP & GIVE ME PERFECT SOLUTION
I have same problem. After switching over in my car to charging only - my Zenfone is also saying "Device is in Charging mode, USB debugging is disabled" I can't find any switch to take it back. Also the same with Media Device not showing in Mobile & PC.
How to make this working again???
The PC connection mode on your phone is set to "Charge only". Idk about the stock ROM, but on CyanogenMod you just press the notification that shows up when you connect the phone to change the mode
wasiq224 said:
The PC connection mode on your phone is set to "Charge only". Idk about the stock ROM, but on CyanogenMod you just press the notification that shows up when you connect the phone to change the mode
Click to expand...
Click to collapse
Dear wasiq224,
Thanks for your answer, but is not working. I'm on CyanogenMod - but there is no notification shown up. Phone is quite and also PC - no message.
Even if I press under "STORAGE" -> "USB computer connection" the phone is saying: "USB is now disconnected". I checked already various menues for some settings without result. Google was also not help in this matter.
Hein_Mueck said:
Dear wasiq224,
Thanks for your answer, but is not working. I'm on CyanogenMod - but there is no notification shown up. Phone is quite and also PC - no message.
Even if I press under "STORAGE" -> "USB computer connection" the phone is saying: "USB is now disconnected". I checked already various menues for some settings without result. Google was also not help in this matter.
Click to expand...
Click to collapse
Try going to Developer Options>Disable USB Debugging, then reboot. Then connect your phone and try going to USB computer connection again, and enable whatever connection mode you want. You can re-enable USB debugging after that.
Dear wasip224
Checked once more the debugging setting's. But if the phone is connected to the computer or not connected, disableing USB Debugging is not possible. This item is greyed out all the time. See attached pictures.
Best regards
Hein Mueck
Same Problem with my device .........
Hein_Mueck said:
Dear wasip224
Checked once more the debugging setting's. But if the phone is connected to the computer or not connected, disableing USB Debugging is not possible. This item is greyed out all the time. See attached pictures.
Best regards
Hein Mueck
Click to expand...
Click to collapse
Same Problem with my device .........
Same with me
ishantanish said:
Same Problem with my device .........
Click to expand...
Click to collapse
With me is the same, i noticed that the Asus driver certificate is expired. If i disable windows driver signature verification it works.
drahhen said:
With me is the same, i noticed that the Asus driver certificate is expired. If i disable windows driver signature verification it works.
Click to expand...
Click to collapse
How you did do this?? Did you uninstall the driver first? Where I can find this?
Hein_Mueck said:
How you did do this?? Did you uninstall the driver first? Where I can find this?
Click to expand...
Click to collapse
I'm at work now, but you use Explorer and go to the folder where you extracted the drivers and use right-click --> properties in one of the files there. There is a tab that lists certificates. Just to be sure you can temporally disable driver signing verification.
http://www.howtogeek.com/167723/how...8.1-so-that-you-can-install-unsigned-drivers/
This instructions works in windows 8.1 and 10.
See picture
drahhen said:
I'm at work now, but you use Explorer and go to the folder where you extracted the drivers and use right-click --> properties in one of the files there. There is a tab that lists certificates. Just to be sure you can temporally disable driver signing verification.
http://www.howtogeek.com/167723/how...8.1-so-that-you-can-install-unsigned-drivers/
This instructions works in windows 8.1 and 10.
Click to expand...
Click to collapse
It's in portuguese but on the right part of the image you can see "Valido a partir de XXXX até XXXX" wich means "Valid from XXXX to XXXX". It expired last month.
Hi all,
Could you install latest Intel USB Driver from this link?
https://software.intel.com/en-us/android/articles/intel-usb-driver-for-android-devices
Reupdate the driver manually and let me know.
Sent from my ASUS_Z00AD
krasCGQ said:
Hi all,
Could you install latest Intel USB Driver from this link?
https://software.intel.com/en-us/android/articles/intel-usb-driver-for-android-devices
Reupdate the driver manually and let me know.
Sent from my ASUS_Z00AD
Click to expand...
Click to collapse
Doesn't work for me, it says it cannot find the files. In my win10 install i have two problems, ADB only works if i disable driver signing verification and MTP doesn't work. I tried running sfc /scannow and it says WinUSB is corrupt and cannot be repaired (probably why MTP does not work). I tried using intel drivers for both and it does not work. Only ASUS works (but fails because of certificate) for ADB Composite Device, but mtp doesn't work anyway.
This tutorial could help you anyway.
http://forum.xda-developers.com/showthread.php?p=64093132
Sent from my ASUS_Z00AD
Dude i tried EVERYTHING, i flashed different roms and the issue persists
k1t4r0 said:
Dude i tried EVERYTHING, i flashed different roms and the issue persists
Click to expand...
Click to collapse
On another PC, or via tutorial on a post before you...
Sent from my GT-I9500
krasCGQ said:
On another PC, or via tutorial on a post before you...
Sent from my GT-I9500
Click to expand...
Click to collapse
Hi Kras and thank for the response!
I Tried it too but in my device manager it wont show any device related to asus nor adb.
Tryied to boot into TWRP but no MTP either.
I Tried USDBview but doesnt show. The strange fact is that the phone charges normally.
It happened after i switched to CHARGE ONLY... after that, could never go back "/
I think i´ll try to revert EVERYTHING to stock. Somethings not right.
Another information, the cellphone charges, i´ve tryied to unistall and reinstall every adb usb_driver but in driver manager, nothing appears, even an exclamation. Tried to force install drivers, nothing either. All this happened after set CHARGE MODE i´m so pissed off and frustrated
This is a shot in the dark, but in device manager you can click View>Show hidden devices.
From there you can truly uninstall all drivers, and then reboot and try reinstalling. Maybe this will help.
Also, different ports, different cables?
If it's just for file transfers have you also tried something like AirDroid or Dropbox/Google Drive/Mega?
Friends,
I've searched through all the threads here and on zentalk but still no good.
I have a ze551 with Superzen, phone works fine however I cannot get it to detect in Windows.
Nothing shows up in device manager, I've tried USB Debugging, MTP and PTP. I've tried 3 different computers (2 x W10 and 1 x W7) and still no good.
The only detection I manage to get is a split second of MOOREFIELD showing up when powering the phone on.
I want to flash MM but cannot adb sideload due to this USB detection issue, any ideas?
What drivers did you install? When I first connected the phone to a pc I installed the Asus drivers but nothing worked. Everything began to work after installing the Intel drivers
h0mbre_au said:
Friends,
I've searched through all the threads here and on zentalk but still no good.
I have a ze551 with Superzen, phone works fine however I cannot get it to detect in Windows.
Nothing shows up in device manager, I've tried USB Debugging, MTP and PTP. I've tried 3 different computers (2 x W10 and 1 x W7) and still no good.
The only detection I manage to get is a split second of MOOREFIELD showing up when powering the phone on.
I want to flash MM but cannot adb sideload due to this USB detection issue, any ideas?
Click to expand...
Click to collapse
try to revoke all usb debugging authorizations from developer options. then disable usb debugging and disable developer option and enable again. now enable usb debugging again. now connect to computer. now run command "adb devices" and authorize from phone.if u still have issue try changing usb cable.
I've tried the Intel drivers., the problem is the phone doesn't even get detected by windows, there's nothing showing up in device manager.
I do however get charging from USB.
I've tried USB 2.0 and 3.0 ports in 3 different computers, no detection.
It used to work fine, now it has just stopped working. Maybe the USB chip is fried or something.
h0mbre_au said:
I've tried the Intel drivers., the problem is the phone doesn't even get detected by windows, there's nothing showing up in device manager.
I do however get charging from USB.
I've tried USB 2.0 and 3.0 ports in 3 different computers, no detection.
It used to work fine, now it has just stopped working. Maybe the USB chip is fried or something.
Click to expand...
Click to collapse
may or may not. may be usb cable broke down data wire, may be connector issue. have you tried above said tips?
Hey,
I got the same problem, and the quick charging takes 7 hours or so, but I should mention previously that in my case the USB port was damaged, so I changed the whole dock. After change tried all other cables including the Asus official cable, still no joy. It looks like some updates made a big fuss in the phone or ... the motherboard is burnt? I tried on different computers with and without Android Intel USB drivers installed, but the problem is the computer cannot see the phone - I'm getting the message that the phone is not sending its designator. I have not rooted my zennfone, but when I try adb to see if the phone is mounted it's not. I was planing to root it now, but it looks like I cannot do anything. I'm affraid that there is something wrong with the hardware. I did started also SMMI test and it loops testing bluetooth, so definitely there is something wrong, but yet I have not figured out.
sukhwant717 said:
try to revoke all usb debugging authorizations from developer options. then disable usb debugging and disable developer option and enable again. now enable usb debugging again. now connect to computer. now run command "adb devices" and authorize from phone.if u still have issue try changing usb cable.
Click to expand...
Click to collapse
Hey mate, thanks for the tip.
I tried this and it did not work.
Still only getting MOOREFIELD if I hold volume down+power but no other detection what so ever
h0mbre_au said:
Hey mate, thanks for the tip.
I tried this and it did not work.
Still only getting MOOREFIELD if I hold volume down+power but no other detection what so ever
Click to expand...
Click to collapse
did you installed intel isoc driver??? if so uninstall it and install intel android usb driver
sukhwant717 said:
try to revoke all usb debugging authorizations from developer options. then disable usb debugging and disable developer option and enable again. now enable usb debugging again. now connect to computer. now run command "adb devices" and authorize from phone.if u still have issue try changing usb cable.
Click to expand...
Click to collapse
sukhwant717 said:
did you installed intel isoc driver??? if so uninstall it and install intel android usb driver
Click to expand...
Click to collapse
I have tried all drivers, the phone was working fine on my windows install and suddenly stopped.
I believe this is not a driver issue, it is hardware issue with the port or with the rom (superzen).
I will try to flash other rom as I have custom recovery and see if it fixes otherwise the port is busted.