i had notice there is alot similar post to this problem but none really solved it. so i start this thread to make it more specific
1) once connected to pc, my wildfire automatically charge
2) no pop-up or option on the top to slide down to select either htc sync, mount as sd card, etc
3) tried reboot, mount unmount card, untick usd debugging, changed other rom, but still not working.
4) if connected to pc still automatically charging even if i change "default connection type" to disk drive, or usb tethering
5) i tick "ask me" so i can choose the connection type when connect to pc, but when connected to pc, nothing. just charging.
i'm rooted, using hg hybrid v3 (problem was there before i flash HG rom). it used to work before. i dont recalled when was the last time it start to behave like this. all this time i thought i set the connection default to charging, but when i want to transfer songs, only then i realised this problem. i m not sure which custom rom might cause this problem (if it does) because i had flash more than 10 roms
i have same problem with cm7
I haven't try to format my sd card. because when I connect without sd card, still no connect option. if my card is malfunction/the main problem, then my phone should work fine n show the connect option after I remove the card, right? (I do have connection option on the setting. what I meant no connection option is the pop up conection menu+connection option on the top bar. changing the connection on the setting change nothing)
I too have this prob but never questioned this as i never use htc sync. But if u really wanna use it try this i'm not sure it may work or not but mostly its due to driver problem:
1.Connect your device in htc sync mode.
2.Uninstall or Remove all drivers of htc and also htc sync.
3.Disconnect your device and Restart your pc.
4.Reinstall htc sync and connect your device in htc sync mode.
5.It'll install fresh drivers for your device and if asked to restart then do it else run htc sync.
If you are running vista or later try to run htc sync in administrator mode.
I'm not sure this method work but there's no problem on trying it. Reply your result after doin above steps
I also think the problem might related to my driver but I remember that when I first connect to my pc, there will be pop up menu, and my phone automatically recognized as "disk drive" (I m not install HTC driver yet. infact ,I install the driver after my phone connected to my pc through disk drive connection since the driver located on the SD card). nway, I"ll try your method and post the result later.
I just notice this might not work..the problem is I cannot change the connection. even if I did, it doesn't change the connection. it just charging.. as if I put it on default "charging" as it connect. but I will try later anyway
When i connect my phone the debugging icon shows up and my pc makes the noise but doesnt let me choose mass storage (running cm7). it shows up on my pc on drive f: but when i click it just says please insert a disc into removable storage F:
xynok, did u tried untick the usb debugging? go to setting, application, development, untick usb debugging. u still lucky at least it prompt u something if u connect to pc, mine nothing. its like I plug it to the socket wall not pc
anakhanjing said:
xynok, did u tried untick the usb debugging? go to setting, application, development, untick usb debugging. u still lucky at least it prompt u something if u connect to pc, mine nothing. its like I plug it to the socket wall not pc
Click to expand...
Click to collapse
yeah i tried that
lokeshramesh said:
I too have this prob but never questioned this as i never use htc sync. But if u really wanna use it try this i'm not sure it may work or not but mostly its due to driver problem:
1.Connect your device in htc sync mode.
2.Uninstall or Remove all drivers of htc and also htc sync.
3.Disconnect your device and Restart your pc.
4.Reinstall htc sync and connect your device in htc sync mode.
5.It'll install fresh drivers for your device and if asked to restart then do it else run htc sync.
If you are running vista or later try to run htc sync in administrator mode.
I'm not sure this method work but there's no problem on trying it. Reply your result after doin above steps
Click to expand...
Click to collapse
not working..
try this if u r using sense roms . Also try this for AOSP roms, if there is an option(i dont know about AOSP).
Go to Settings/Applications/Manage applications/All/
Then search for "Connect to PC". Actually in stock roms that was an app by htc. But there must be something similar to that in AOSP roms. Then open that and select, "Force stop" , "Clear data", "Clear cache".
I dont know for sure if that solves the issue or not. But have a try.
And by seeing this thread, actually i got a doubt, "can we synchronise the htc sync in AOSP custom roms". Since AOSP is nothing but removing the HTC crap. Can someone confirm this .......
bharatgaddameedi said:
try this if u r using sense roms . Also try this for AOSP roms, if there is an option(i dont know about AOSP).
Go to Settings/Applications/Manage applications/All/
Then search for "Connect to PC". Actually in stock roms that was an app by htc. But there must be something similar to that in AOSP roms. Then open that and select, "Force stop" , "Clear data", "Clear cache".
I dont know for sure if that solves the issue or not. But have a try.
And by seeing this thread, actually i got a doubt, "can we synchronise the htc sync in AOSP custom roms". Since AOSP is nothing but removing the HTC crap. Can someone confirm this .......
Click to expand...
Click to collapse
nope. still nothing. anyway since it had this problem, I had wipe my wildfire few times, n try different rom.. maybe it is because of faulty cable. but if the cable is the culprit, why it still charging? is it possible the cable is broken but still can charging?
anakhanjing said:
nope. still nothing. anyway since it had this problem, I had wipe my wildfire few times, n try different rom.. maybe it is because of faulty cable. but if the cable is the culprit, why it still charging? is it possible the cable is broken but still can charging?
Click to expand...
Click to collapse
Not telling that it should be, but definitely there is a possibility of a cable culprit.
The USB male/female end has 4 connections in which two connections are used for voltage and the remaining two connections are used for data transfer.
There might be a possibility that the data connection got broken with voltage connection retaining. Try with another cable (any USB v2 cable).
And one more thing, for having the disk drive option, nothing need to be installed in the pc. U need to install htc driver in the pc only if u want to use usb debugging , usb tethering.
[But at the wildfire end the cable has 5 connections and i dont know what the 5th one is for. mostly it will be a NO CONNECTION]
Now i got another idea to diagnose ur issue.
Well do u know of application "pdanet". It uses USB DEBUGGING feature to tether ur phone internet to PC. Actually usb debugging can be used both under charge mode and disk drive mode. What u can know on doing this is whether usb debugging through ur phone is working or not. U can diagnose the thing while checking with every app that uses usb debugging. So try it. Enable the usb debugging in phone first.
---Install pdanet desktop version and follow the setup instructions. It asks to connect ur phone during setup to install usb driver and also pdanet.apk to mobile. Connect ur phone with usb debugging enabled. I doubt whether desktop version installs or not because of ur issue. Mostly desktop version of pdanet will not install without a phone connected having usb debugging enabled. And if the desktop version is installed successfully, that means ur phone usb debugging is working. And if desktop version is installed successfully, that means it also installed the mobile version of pdanet.apk to ur phone (which says that data transfer is working). Then open the pdanet on phone and enable usb tether. Then open pdanet from desktop and connect. Then see whether u r able to access internet from pc.
---One more method is try to use ADB from android sdk. It also uses the usb debugging feature.
If adb and pdanet works, that means usb debugging feature on ur phone is working. If it is so, then it is mostly not a cable problem (as far as i know). And if they dont work there is a chance that it is a cable problem.
......................................................................................................................................................................................
And one more thing. If u have used a stock rom (freshly formatted), and faced the issue, then it is mostly not a software problem. Then it might be cable problem or some kind of problem in ur phone. Also check ur phone radio version. Thats all.
bharatgaddameedi, i cant install pdanet. it say android phone not detected. error =103. i think u were right. its hardware related problem but its look like not the cable. most probably its my wildfire usb jack. i test the cable with other mobile, its working (test it on nokia 5800). before i had this problem, sometime i use htc cable to transfer data for my 5800, and some time i used 5800 cable to transfer data for my wildfire. the difference between the two cable pin might damage my wildfire usb jack.. (u said htc cable got 5 pin, so i asume nokia got 4?)
anakhanjing said:
bharatgaddameedi, i cant install pdanet. it say android phone not detected. error =103. i think u were right. its hardware related problem but its look like not the cable. most probably its my wildfire usb jack. i test the cable with other mobile, its working (test it on nokia 5800). before i had this problem, sometime i use htc cable to transfer data for my 5800, and some time i used 5800 cable to transfer data for my wildfire. the difference between the two cable pin might damage my wildfire usb jack.. (u said htc cable got 5 pin, so i asume nokia got 4?)
Click to expand...
Click to collapse
So, pdanet not detecting the phone means usb debugging is also not working under charge mode. That should be phone hardware related problem like u have said about usb jack.
And No. All the micro USB version 2 cables will be the same. Its same for 5800 and wildfire. I use my previous 5233 cable to my wildfire even now.
The usb jack of wildfire may damage if u have used it in an improper way. Something like pressure on the cable when connected and so on...
So, its not something we can solve here. That should be given to service centre as far as i know
anakhanjing said:
the difference between the two cable pin might damage my wildfire usb jack.. (u said htc cable got 5 pin, so i asume nokia got 4?)
Click to expand...
Click to collapse
Can't be. I am using my N82's data cable for data transfers on my Wildfire from Day 1. The provided data cable is pretty much permanently attached to the wall charger.
I accept the fact that it might be hardware problem but there is one more thing I want to try. how about flashing stock rom from pc? flashing 2.1 is ok since it can be rooted again. I had flash stock rom but from the clockwork mod, not from pc, and the hboot is been remove for save flashing. I never try this before because all this time I thought that the problem was cause by custom rom, so I just need to find the right custom Rom.
How can u flash a stock Rom from pc when the usb is not functioning. RUU will not work.
Things get worse when basic things stop functioning.
Sent from my HTC Wildfire using XDA App
Did you try mounting your SD Card via Recovery? Reboot into Recovery > Advanced > Mount SDCard
Related
Hey there.
Ok I have a problem. I have had my touch pro 2 for about 6 months now and i am really happy with it, but recently i have ran into a problem.
My phone won't connect to my computer anymore! Not just my computer... no computer at all. Not just activesync, no, it doesn't recognise it at all, not even as a disk drive.
I doubt its the cable because it does charge, and i have tried another cable (not a htc cable but its a cable with the same plug, its from my external harddrive) and it still didn't work.
I also tried a hard-reset on my phone, but still... nothing.
Ive read somewhere that you should push the usb connector a bit up, i did that, but nothing (now the usb connector seems wiggly... glad it still charges though) i have no idea what it could be and i thought i'd post here first before going back to the dealer with it. Because without usb connection i can't install costum roms and that we wouldn't want that, do we?
Well, hope one of you guys can help!
That's very strange I have had it once, but that was due to the rom I used. I flashed another rom and it worked again.
What you could try is to download a new rom and put it on your sd car using this:
http://www.julien-manici.com/windows_mobile_wifi_remote_access/
This let's you put stuff on your mobile using wifi. It's worth a try.
But you have to install roms directly from your pc to your phone, while being connected to USB right? The standards htc roms for example can only be installed that way i think... or can you also copy the .exe to your device and run that?
i'll give it a go when i get home. Thanks =]
I am having the same issue here. All of a sudden my PC or Laptop doesn't see the phone at all but it does charge with no issues. When I plug it in I don't even get the sound that the PC knows something was jut plugged into it.
go to settings - connection - usb to pc - untick the enable faster synchronization box
that should do it
As long as you have Hard SPLed your Rhodium you should be able to use the sd card method to install a rom instead of using the PC and usb connection.
You copy the rhodium.nbh file to the root directory of an sd card formatted FAT32 and then boot into bootloader - volume down and power button when off.
Follow the onscreen prompts...
Cheers...
This sounds familiar - http://forum.xda-developers.com/showthread.php?t=741406
Lennyz1988 said:
That's very strange I have had it once, but that was due to the rom I used. I flashed another rom and it worked again.
Click to expand...
Click to collapse
What's interesting with my Tilt2 (not the OP) was that I wanted to flash my ROM with the new AT&T "unofficial" ROM and that's when I found out I couldn't tether. I basically just wanted to tether my phone so I could put that new ROM onto the phone to see if I could make it more reliable and faster. Sigh.
it actually might be the cord...
The same exact thing happened to me... my phone charged with the cord but no computer recognized it...
I bought a new usb cable from radio shack and viola it worked again... so I advise u just trying a new one and if it doesn't work take it back... but try the unchecking the "check for faster sync" box first like someone said bc that do stop it from being recognized sometimes...
mr_sheen said:
go to settings - connection - usb to pc - untick the enable faster synchronization box
Click to expand...
Click to collapse
Yes, this has (almost) always fixed the issue for me. Somehow WDC becomes blind to new device inserts after you plug-unplug them several times.
Slow but stable is better.
I was trying to put the hum/hiss sound fix on my sd card and I cannot get my pc to connect via USB...
My wife has a TP2 and it connects fine...
I have tried with/without the sd card in, rebooted the pc and phone, rebooted the phone while connected to the pc.... nothing...
wtf...
anyone else with this problem?
PS... NRGZ28 had posted a very basic rom for booting to android back in Feb and it is now gone from hotfile. Anyone know of a quick boot into android?
- Try a different computer
- Try a hard reset
That are the first thing you should do.
Tried hard reset...
Dif PC is not an option at the moment... I have rebooted...
Just flashed the ROM (NRGZ newest, thank goodness I had it on my SD card) and I still cant get it to sync...
I have attached the USB error I am getting... (Win7, new install)
The phone is not asking if I want to active sync or use as storage???? wtf...
FarBeyond said:
Just flashed the ROM (NRGZ newest, thank goodness I had it on my SD card) and I still cant get it to sync...
I have attached the USB error I am getting... (Win7, new install)
The phone is not asking if I want to active sync or use as storage???? wtf...
Click to expand...
Click to collapse
Reboot your PC? lol bet your tried that already...
Try this:
settings > connections > usb to pc > and disable Faster Data Sync then try. This way uses the generic usb drivers and maybe it will connect.
That did not work...
How do I get my Win7 laptop to see the phone with Android on it?
FarBeyond said:
That did not work...
How do I get my Win7 laptop to see the phone with Android on it?
Click to expand...
Click to collapse
dont think thats working yet
Ya I don't think that works yet, it's tied to Android software drivers and the use of the USB port, since there is no drivers to control the port only to charge battery. Windows thinks there is something there, but the phones USB can't communicate back....I think this is the issue or at lease after playing around with it on my phone anyway
Not that it's a huge amount of help but might troubleshoot down to the hardware level...if you go into bootloader mode on the phone and connect to USB does it connect?
I don't think you should go that deep and dirty. My touch pro 2 works only with only 1 (non-HTC) cable of the 10 i have at home, all are the "standard" mini-USB but only one works flawlessly for communicating/flashing/syncing, the other cables either do the same error - device not recognized - or windows says that the device could communicate faster - and only copies files slowly.
All in all: you should simply check with another USB cable or if you have the factory HTC cable try it with that. I noticed that the cable i am using other than the HTC one is a very good quality thick (low-resistance and double-shielded) USB cable and it never failed on me.
One other thing you should definitely watch for: plug the USB cable into the motherboard USB port directly (on the back of the PC where you plug the keyboard, mouse etc.), sometimes PC cases with front panel USB outputs simply die, or are wrongly attached to the motherboard USB header and it can cause the aforementioned problems too, not to mention if it is wrongly attached it could harm your phone too.
Hi,
I have got HTC DESIRE a day back, I am unable to connect my device to pc, when I plug the cable to PC nothing, neither mobile shows any thing nor PC. Also the device dont start charging. to charge I have to turn the devise of, connect the cable to PC it starts charging then, & if I turn the mobile on it still charges but dont connect to PC,
I have android 2.2, I think its the issue with of OS, is there any way I can reinstall the OS again? my device is not rooted,
Please Help me out, Thanx in advance.
Regards
Hi there
i cant sync my desire,pls help,sync program doesnt recognize my phone, windows 7
aliasif2010 said:
Hi,
I have got HTC DESIRE a day back, I am unable to connect my device to pc, when I plug the cable to PC nothing, neither mobile shows any thing nor PC. Also the device dont start charging. to charge I have to turn the devise of, connect the cable to PC it starts charging then, & if I turn the mobile on it still charges but dont connect to PC,
I have android 2.2, I think its the issue with of OS, is there any way I can reinstall the OS again? my device is not rooted,
Please Help me out, Thanx in advance.
Regards
Click to expand...
Click to collapse
The problem wherein the device doesnt charge when connected directly, and starts charging after plugged in while switched off, is not unique to you. I have faced the same issue. However I have been unable to solve it fully. Cynogenmod Rom when installed does not have this issue, and seems to be unique to Sense based Roms.
Have you installed HTC Sync?
If so, try uninstalling all three HTC Software from Windows-HTC Sync, the Driver Setup, and BMP Driver.
Disconnect the phone.
Now reboot the PC.
Reinstall HTC software fully.
Reboot PC again.
Now start up HTC Sync, and now connect the Usb cable.
droidzone said:
The problem wherein the device doesnt charge when connected directly, and starts charging after plugged in while switched off, is not unique to you. I have faced the same issue. However I have been unable to solve it fully. Cynogenmod Rom when installed does not have this issue, and seems to be unique to Sense based Roms.
Have you installed HTC Sync?
If so, try uninstalling all three HTC Software from Windows-HTC Sync, the Driver Setup, and BMP Driver.
Disconnect the phone.
Now reboot the PC.
Reinstall HTC software fully.
Reboot PC again.
Now start up HTC Sync, and now connect the Usb cable.
Click to expand...
Click to collapse
Thanks for your response, Actually I am unable to connect my device to pc, then how can i install any other ROM??
The procedure I have read from the websites require the PC to be connected with the device.
Also I didnt installed three things in my PC to sync, I just installed the HTC sync I downloaded it from the HTC website, Please tell where can I find the other two things.
Also there is an update, I have replaced the cable, Now when I connect the device to the PC, windows 7 shows un known device. But nothing is shown in the Mobile, no notification, & no list to select either "charge only" or "Disc Drive" etc
Thanks for your help
Regards
Hmm this sounds allmost exactly as USB-brick (i had one). Did you buy completely new phone or used one. You say its unrooted? Have you messed with your phone (flashing custom roms etc)?
godina said:
Hmm this sounds allmost exactly as USB-brick (i had one). Did you buy completely new phone or used one. You say its unrooted? Have you messed with your phone (flashing custom roms etc)?
Click to expand...
Click to collapse
No the phone is used one, but used only 2 or 3 days with no any scratch or any mark on it. I would have to replace the USB port of the device??
Hey Guys and Girls.
Till few days ago my DHD was working just fine.
Now when I connect it to pc nothing happens, just show that its charging.
Phone is not showing that I can chose USB type, and pc is not recognizing anything, even in computer manager.
Weird thing is showing in phone application manager, when Im going to transfer app to sd, its show "TRANSFER TO PHONE STORAGE", but when is on sd it show "TRANSFER TO PHONE".
I think I tried everything. Pls help.
1. I instal 3 version of custom Rom and still same thing.
2. I test my sd in computer and other phone, work fine.
3. I tried original USB and other USB and nothing.
4. No pc can recognize phone.
Sound like you don't have the usb driver installed on your PC.
Install HTC sync to get the drivers. You can uninstall afterwards, but leave the drivers installed.
Sent from The App that Time Forgot.
I tried few times to reinstall HTC Sync , I also tried to instal older HTC Sync and nothing. Phone when connected not showing USB options, it only show that its charging, same as when I plug it in to wall charger.
Can someone trie to see my weird problem in app manager as I wrote in first post.
Thanks, I realy need help, don't want to buy another phone
And another thing, when u connect your mobile phone to any pc, it will ask you to chose USB connection type, even u don't have instaled drivers, u can use it as device USB storage
Try a different cable, or a different phone on that cable.
If a different cable works, the old one is dead.
If a different phone works on that cable, you have an issue with the phone.
If neither work on either phone / cable, try a different PC.
What firmware are you running?
I'm using RcMix 3d, runnymede 4.0.
2.3.5 with sense 3.5.
Cables are working with other phones,
Maybe my phone lose driver or something. Hmmmm
You could maybe try a full wipe, and/or reinstalling the rom.
Better yet - backup your current rom, then wipe and see if your phone connects. If it does, I'd restart from there.
One more thing.
When I'm going to backup my desire hd, everything is fine,
But on sd-ext its say no sd-ext backup skipped.
Maybe that's the problem?
So I'm trying to unlock the bootloader so I can install some nice roms.
How ever when I try to install the update RUU HTC advices me to install nothing happens.
I get to "Connect your phone to the computer using the USB cable that came with your phone. Wait a moment for your computer to identify your phone, this may take a few minutes.
If your computer cannot find your phone, you may need to install HTC Sync. You can download HTC Sync here.
"
How ever the phone never gets recognized so running the RUU causes it to load and then close before giving me any options.
Hboot version is 0.90.0000 software version is 2.13.351.1
I've looked all over XDA and google for answers and couldn't find anything that worked.
Is there any other way to flash the RUU ? Fastboot maybe? ( I tried just running the RUU whilst in fastboot usb and it RUU still loads and then closes)
Oh yeah, trying to do all this on Win7 x64
*edit* Running the phone in usb storage mode allowed it to run, how ever thus far it does not seem to be working. Got an error message saying a directory was full. It's now" Veryifing information on your pda phone" been doing it a while though.
First:
Go into Settings, then choose Connect to PC.
Make sure "Ask Me" has a checkmark on it.
Second:
In the settings choose Applications, then Development and make sure USB debugging is checked off also.
When you connect the USB cable to the computer now do you get a message on your phone?
You should have three chooses for USB type; charge only, HTC Synch and Disk Drive.
If you are not getting this option then your computer is not connecting to the phone via USB. Either bad usb cable, bad usb port, or something wrong with the phone.
EDIT
Sorry just saw your edit. disregard my comment.
kmbarreiros said:
First:
Go into Settings, then choose Connect to PC.
Make sure "Ask Me" has a checkmark on it.
Second:
In the settings choose Applications, then Development and make sure USB debugging is checked off also.
When you connect the USB cable to the computer now do you get a message on your phone?
You should have three chooses for USB type; charge only, HTC Synch and Disk Drive.
If you are not getting this option then your computer is not connecting to the phone via USB. Either bad usb cable, bad usb port, or something wrong with the phone.
Click to expand...
Click to collapse
I get all these options, I can access the disk drive if I choose that option, if I choose sync that works etc.
Only this RUU that gives me problems
*EDIT* WOOO! found a work around, run RUU with storage mode on, then switch back to charge only after accepting disclaimer.
*Edit again* and of course, just as things seem to be going well the installer crashes, now the phone is stuck on some silver HTC logo.
It crashes as soon as it tells the phone to reboot to bootloader.
Bumping this instead of making a new thread.
Still having this issue if anyone can help.