need help asap please - Micromax Canvas A1

flashed stock rom succesfully but I checked my warranty using fastboot getvar all command warranty shows no. what to do now?? :crying::crying:

reply
K1Ng0r.fTw~ said:
flashed stock rom succesfully but I checked my warranty using fastboot getvar all command warranty shows no. what to do now?? :crying::crying:
Click to expand...
Click to collapse
Relocked bootloader ?? and flashed via sptools??

bhavarsh1234 said:
Relocked bootloader ?? and flashed via sptools??
Click to expand...
Click to collapse
flashed via sp tool and bootloader is also locked still "getvar all" command shows warranty status:No :crying:

K1Ng0r.fTw~ said:
flashed via sp tool and bootloader is also locked still "getvar all" command shows warranty status:No :crying:
Click to expand...
Click to collapse
u tried download mode if yes then try firmware upgrade because i have read in a post in thread to gain warranty back flash it by this method but can u gave me the stock file u flashed on micromax canvas a1 because i flashed it then my phone was not turning on

bhavarsh1234 said:
u tried download mode if yes then try firmware upgrade because i have read in a post in thread to gain warranty back flash it by this method but can u gave me the stock file u flashed on micromax canvas a1 because i flashed it then my phone was not turning on
Click to expand...
Click to collapse
ya i did download mode but r u sure? firmware upgrade gain warranty back?? please confirm from some developer. i flash this file on mmx a1
http://forum.xda-developers.com/canvas-a1/development/official-stock-rom-canvas-a1-t2887150
Installation instruction:
Code:
Step 1 :- Firstly Download and Install USB Drivers in your PC from the download Section Below.
Step 2 :- Now Download Main ROM Zip and SP Flash Tools.
Step 3 :- After downloading Extract Them Into A Separate Folder into your PC. [Please Turn off Your Anti-Virus During The Process For Some Time.]
Step 4 :- Now Switch-Off You Canvas A1 , Remove Battery & Re-Insert It to Ensure that its Properly Switched Off.
Step 5 :- Next Open SP-Flash Tools From The Same Extracted Folder.
Step 6 :- Now click Click Scatter Loading & Select The ‘MTTK65XX_Scatter.txt‘ From The Directory Where you extracted the Main ROM.
Step 7 :- Hit the Download button and SP Flash Tools will start searching for your device.
Step 8 :- Now connect your device with a USB Cable in the switch off mode.
Step 9 :- Your device will be detected by SP Flash Tools and Upgrade Process will start.
Step 10 :-The process will complete in 3-4 minutes and then a success popup will appear, now disconnect your phone reinsert its battery and power it on.
That’s it, FIrst boot will take about 4-5 minutes wait for it and enjoy stock Experience.

K1Ng0r.fTw~ said:
ya i did download mode but r u sure? firmware upgrade gain warranty back?? please confirm from some developer. i flash this file on mmx a1
http://forum.xda-developers.com/canvas-a1/development/official-stock-rom-canvas-a1-t2887150
Installation instruction:
Code:
Step 1 :- Firstly Download and Install USB Drivers in your PC from the download Section Below.
Step 2 :- Now Download Main ROM Zip and SP Flash Tools.
Step 3 :- After downloading Extract Them Into A Separate Folder into your PC. [Please Turn off Your Anti-Virus During The Process For Some Time.]
Step 4 :- Now Switch-Off You Canvas A1 , Remove Battery & Re-Insert It to Ensure that its Properly Switched Off.
Step 5 :- Next Open SP-Flash Tools From The Same Extracted Folder.
Step 6 :- Now click Click Scatter Loading & Select The ‘MTTK65XX_Scatter.txt‘ From The Directory Where you extracted the Main ROM.
Step 7 :- Hit the Download button and SP Flash Tools will start searching for your device.
Step 8 :- Now connect your device with a USB Cable in the switch off mode.
Step 9 :- Your device will be detected by SP Flash Tools and Upgrade Process will start.
Step 10 :-The process will complete in 3-4 minutes and then a success popup will appear, now disconnect your phone reinsert its battery and power it on.
That’s it, FIrst boot will take about 4-5 minutes wait for it and enjoy stock Experience.
Click to expand...
Click to collapse
Brother i read it in this thread from where u got stock file brother i also used this stock file yesterday but my phone was not turning on i think i removed the battery then flashed that is the reason i think but then i used firmware upgrade mode it relocks the bootloader because today i went to mmx center and they updated software without any charges

bhavarsh1234 said:
Brother i read it in this thread from where u got stock file brother i also used this stock file yesterday but my phone was not turning on i think i removed the battery then flashed that is the reason i think but then i used firmware upgrade mode it relocks the bootloader because today i went to mmx center and they updated software without any charges
Click to expand...
Click to collapse
i flash firmware with battery. no need to remove then flash. they updated software what do u min??

Related

[GUIDE]Root Xolo HIVE 8x-1000 and other MTKxxxx impossible to root devices easily!

Hello all XDA Members and others who are viewing this thread.
I finally found a way to root the IMPOSSIBLE TO ROOT MediaTek devices!
I personally used it on Xolo HIVE 8x-1000 MT6592M with 2 Gb RAM 1.4 Ghz Octa Core Processor MT6592M.
Devices that won't be rootable by apps like Kingo Root, Vroot(for a certain time), Framaroot, towelroot etc can be rooted and have CWM recovery installed.
Xolo HIVE 8x-1000 users can also follow this guide created by The Android Soul for picture tutorial. : Click Here
Note : If you're rooted but want to install CWM then follow this guide to create CWM and flash it via SP Flash Tool or Just copy the created recovery and flash it via Rashr (Download from play store)
Let's get started without wasting time.
Things you'll need MTK Drivers : All MTK Drivers 2014
Your Phone with USB Debugging Mode turned on in Developer Section
Usb Cable and most Important
A Calm head :silly:
A video is already available link is in 1st point.
Code:
[B][SIZE="3"]Warning Rooting Voids warranty. I would in any means not be responsible for dead devices, bricked SD cards or any other activity that leads to damage of your device. If you know the risks still want to continue then go ahead.[/SIZE][/B]
First we would like to load scatter file for our device. Process in the video link in 1st point.
Disconnect the phone's battery (if any) [ IN CASE OF XOLO HIVE JUST SWITCH OFF THE DEVICE THEN WAIT FOR 30 seconds and connect the device ] and then press volume up button and connect it with PC it will connect device in preloader mode.
1) We would like to have a backup of our UNROOTED stock ROM. Download MTK Droid Tools (Google it) and then use this method to backup your UNROOTED stock ROM. It is basically Read Back method from SP Flash tool Follow this video tutorial : How to backup unrooted stock ROM
Warning : Please do not continue this tutorial if your device has fake information or any kind of restriction or ubifs file system or you'll brick the device. You have been warned.
This is a text guide for the video :
2) After backup extract the firmware you created using MTK Droid Tools. Process given in video.
3)Now when you get boot.img for your device you're good to go
4) Open MTK Droid tools with administrative privileges and make sure your phone is connected and then migrate to root,backup,recovery tab and click the option to choose boot.img from and locate your stock boot image and make a CWM recovery from it.
5) Wait for process to complete and then check recovery folder inside MTK Droid tools folder. There you'll find two files
Code:
[COLOR="Red"][B]XXXX_bootpatched.img & XXXX_recovery.img[/B][/COLOR]
6) Now open SP flash tool and load the MTKXXXX_Android_scatter_txt and untick every option except for boot.img and recovery.img. Then click on both tabs and locate the modified images created by MTK Droid tools which can be found in recovery folder itself if you haven't moved them.
7) Make sure your phone isn't connected at this time and then hit download button in SP Flash Tool and then with phone's battery removed with volume up button pressed connect it to PC and then flash process will begin. After completion you'll see a green circle at that point disconnect your phone and switch it on. Don't disturb the phone until flashing completes and you see a green circle.
Congratulations! You have CWM Recovery for your device without ROOT!
ROOTING
1) Now download this zip file and flash it via CWM Recovery. SuperSU.zip and reboot.
Congo many will get root access now but not Xolo HIVE You do need to flash this zip. Users that don't get root after flashing supersu zip can also continue further.
2) Download Vroot from here and install it.
3) Connect your phone with USB Debugging on and wait till it detects your device.
4) Now click root button and voila you're rooted!
Now reboot and you'll see the superuser app Now you'll have two Superuser apps (NOT XOLO HIVE USERS) SuperSU from flash and Superuser from Vroot. Not to worry just open SuperSU and it will automatically ask to remove the other Superuser app choose that and reboot and you're done
Luckily those who don't want or find complication in SP Tool Read back method, just download the stock ROM for your device and extract boot.img from it and then follow same steps from 4th step at the beginning from where to create CWM for your device.
I suggest use androidxda.com for most stock ROM's.
Xolo HIVE 8x-1000 users don't Panic I have your CWM and Boot image ready Just download from here : Xolo HIVE Recovery.img
Xolo HIVE Boot Patched.img.
KINDLY DON'T MIRROR MY FILES. IF YOU WANT TO SHARE GIVE THIS LINK TO PEOPLE.
Xolo HIVE users I saved your work upto step 5 from step 6 ,i.e, flashing you need to do manually
I know it's a long and complicated process but it is only method working until a new exploit is available to root the impossible mtk devices.
Conisder me a donation if you can as it will help me to make more guides and apps
If you cant donate hit thanks :good:
That won't cost you!
EDIT : I am adding Xolo MT6592 scatter file too in case you can't generate it. Remember to load scatter file uncheck all options leaving boot.img and recovery.img then flash the boot and recovery I provided ONLY XOLO HIVE USERS
Tech N You said:
Hello all XDA Members and others who are viewing this thread.
I finally found a way to root the IMPOSSIBLE TO ROOT MediaTek devices!
I personally used it on Xolo HIVE 8x-1000 MT6592M with 2 Gb RAM 1.4 Ghz Octa Core Processor MT6592M.
Devices that won't be rootable by apps like Kingo Root, Vroot(for a certain time), Framaroot, towelroot etc can be rooted and have CWM .
Click to expand...
Click to collapse
bro i want to ask you about the scatter file, because you have not provided that and it is most useful. i have a xolo hive 8x 1000 and when i am trying to generate scatter file then this error comes. and i have read that this can brick the phone. And the person in the video you suggested in step 1 also said in his video not to proceed if any error comes. so please help.
Scatter file can be easily made :?
You just have to click block path tab it won't brick :/
Also I have provided Xolo HIVE recovery and bootpatched file! Just download this and flash it via SP Flash Tool! You can create scatter yourself! Watch the video!
Connect your phone with USB Debugging on and connect to PC and let mtk droid tools read it.When it does then you click on blocks map tab!
Sent from my 8x-1000 using XDA Free mobile app
Added the scatter file there you go check the post
Tech N You said:
Added the scatter file there you go check the post
Click to expand...
Click to collapse
Alright bro thanku so much..
And if u have rooted your xolo 8x 1000 then please provide a video link or tutorial. Thnxx
What above I wrote is tutorial only
Switch off the phone open sp flash tools load scatter file and uncheck all boxes excluding boot.img and recovery.img make sure you downloaded the recovery.img and boot.img I attached in the post, just locate my given recovery.img and boot.img and click download button on sp flastool then connect your phone while u keep the volume up button pressed. Now the process will begin and it will give a green circle on successful completion. Switch on the device install vroot on PC I gave link in thread then just connect your phone with USB debugging on and then wait for Vroot to detect the phone then click root and you're done.
Sent from my 8x-1000 using XDA Free mobile app
Tech N You said:
What above I wrote is tutorial only
Switch off the phone open sp flash tools load scatter file and uncheck all boxes excluding boot.img and recovery.img make sure you downloaded the recovery.img and boot.img I attached in the post, just locate my given recovery.img and boot.img and click download button on sp flastool then connect your phone while u keep the volume up button pressed. Now the process will begin and it will give a green circle on successful completion. Switch on the device install vroot on PC I gave link in thread then just connect your phone with USB debugging on and then wait for Vroot to detect the phone then click root and you're done.
Sent from my 8x-1000 using XDA Free mobile app
Click to expand...
Click to collapse
y so rude? and please tell me about this. sp flash tool is not detecting my phone i exactly followed what u have said above but no success. tried installing pdanet 3 times with my phone connected even installed drivers manually with signature enforcing off.
Install all mtk drivers from the link I gave in the thread and before installing them make sure to delete the previous drivers
Sent from my 8x-1000 using XDA Free mobile app
Tech N You said:
Install all mtk drivers from the link I gave in the thread and before installing them make sure to delete the previous drivers
Sent from my 8x-1000 using XDA Free mobile app
Click to expand...
Click to collapse
ok i did it thanxx bro.
Anytime
Sent from my 8x-1000 using XDA Free mobile app
See the method to root kitkat 4.4.2 for C2C, link in my signature, flashing that zip will root any device with kitkat/Jellybean, no need to use vroot
umangleekha said:
See the method to root kitkat 4.4.2 for C2C, link in my signature, flashing that zip will root any device with kitkat/Jellybean, no need to use vroot
Click to expand...
Click to collapse
Flashing cwm recovery via sp flashtool doesn't makes you rooted. It just replaces stock recovery
Tech N You said:
Flashing cwm recovery via sp flashtool doesn't makes you rooted. It just replaces stock recovery
Click to expand...
Click to collapse
Read carefully, after flashing cwm, i said to flash that root zip, and after flashing that root zip, no need to use vroot or other methods
umangleekha said:
Read carefully, after flashing cwm, i said to flash that root zip, and after flashing that root zip, no need to use vroot or other methods
Click to expand...
Click to collapse
Well nothing worked for Xolo Hive if you read my guide too. Flashing SuperSU.zip ends up in a infinite binary update with failure
can you please root xolo 8x-1100
i also don't have pc
I certainly have helped rooting Xolo 8x-1100 and 8x-1200 to a member.
You need PC for flashing boot.img and recovery.img, Sorry my friend: (
Or try rooting via towelroot first then tell me if you succeed.
Also download your stock ROM from here and send me the recovery.img from it follow this link and download : Xolo Play 8x-1100 stock rom
Sent from my 8x-1000 using XDA Free mobile app
badshah.mb said:
can you please root xolo 8x-1100
i also don't have pc
Click to expand...
Click to collapse
Check my above post
xolo 8x 1000
successfully rooted the xolo 8x 1000 with iroot....thanks man
Problem with the root
unable to flash custom recovery even after following every step to the dot. What might the problem be?
my phone isnt rooted im trying to root my phone.
BUT CANNOT
kindly find a solution.
Stuck at bootloop.
Guys,I'm stuck at the boot logo.
Nothing is working.Neither CWM recovery nor ADB. Please help me and give a CWM recovery zip file.

[Official][Stock][4.4.4] Mircromax Canvas A1 (Android One)

@mohsin.r.munshi Already Created thread in android development section about stock rom. But he is not mentioned installation method for noobs So I setup new thread.
Hello Developers.
Pre-Requisite:
1. http://goo.gl/aGMN8e
2. http://goo.gl/tczCMx
Downloads:
1. http://goo.gl/79N7u7
Installation Method: [With SP flash tool]
Before proceeding further please make a backup of your device with CWM Recovery or MTKDroid Tools.
Step 1 :- Firstly Download and Install USB Drivers in your PC from the download Section Below.
Step 2 :- Now Download Main ROM Zip and SP Flash Tools.
Step 3 :- After downloading Extract Them Into A Separate Folder into your PC. [Please Turn off Your Anti-Virus During The Process For Some Time.]
Step 4 :- Now Switch-Off You Canvas A1 , Remove Battery & Re-Insert It to Ensure that its Properly Switched Off.
Step 5 :- Next Open SP-Flash Tools From The Same Extracted Folder.
Step 6 :- Now click Click Scatter Loading & Select The ‘MTTK65XX_Scatter.txt‘ From The Directory Where you extracted the Main ROM.
Step 7 :- Hit the Download button and SP Flash Tools will start searching for your device.
Step 8 :- Now connect your device with a USB Cable in the switch off mode.
Step 9 :- Your device will be detected by SP Flash Tools and Upgrade Process will start.
Step 10 :-The process will complete in 3-4 minutes and then a success popup will appear, now disconnect your phone reinsert its battery and power it on.
That’s it, FIrst boot will take about 4-5 minutes wait for it and enjoy stock Experience. :laugh:
And the Phone is as good as new
archies20 said:
@mohsin.r.munshi Already Created thread in android development section about stock rom. But he is not mentioned installation method for noobs So I setup new thread.
Hello Developers.
Pre-Requisite:
1. http://goo.gl/aGMN8e
2. http://goo.gl/tczCMx
Downloads:
1. http://goo.gl/79N7u7
Installation Method: [With SP flash tool]
Before proceeding further please make a backup of your device with CWM Recovery or MTKDroid Tools.
Step 1 :- Firstly Download and Install USB Drivers in your PC from the download Section Below.
Step 2 :- Now Download Main ROM Zip and SP Flash Tools.
Step 3 :- After downloading Extract Them Into A Separate Folder into your PC. [Please Turn off Your Anti-Virus During The Process For Some Time.]
Step 4 :- Now Switch-Off You Canvas A1 , Remove Battery & Re-Insert It to Ensure that its Properly Switched Off.
Step 5 :- Next Open SP-Flash Tools From The Same Extracted Folder.
Step 6 :- Now click Click Scatter Loading & Select The ‘MTTK65XX_Scatter.txt‘ From The Directory Where you extracted the Main ROM.
Step 7 :- Hit the Download button and SP Flash Tools will start searching for your device.
Step 8 :- Now connect your device with a USB Cable in the switch off mode.
Step 9 :- Your device will be detected by SP Flash Tools and Upgrade Process will start.
Step 10 :-The process will complete in 3-4 minutes and then a success popup will appear, now disconnect your phone reinsert its battery and power it on.
That’s it, FIrst boot will take about 4-5 minutes wait for it and enjoy stock Experience. :laugh:
And the Phone is as good as new
Click to expand...
Click to collapse
Reserved!!
archies20 said:
Reserved!!
Click to expand...
Click to collapse
this won't work either .. u missing key points ..
Faiyaz5yaz said:
this won't work either .. u missing key points ..
Click to expand...
Click to collapse
what do u mean??
Some guys here are only for time pass so don't worry .
I have used this . worked for me
After stock u need to relock OEM if unlocked ...
Fastboot ur phone and did the same adb and fastboot files type this in cmd
Fastboot OEM lock
Sent from my Micromax AQ4501 using XDA Free mobile app
archies20 said:
what do u mean??
Click to expand...
Click to collapse
Some beings come here only to promote their websites,!!!!
And by the way ,
You must have unlocked bootloader to flash this stock rom.. you can never flash this rom on a locked bootloader.. Infact the process will never start!!!
And the op has updated now After i tested and confirmed ..
And also The bootloader gets locked Automatically..!!!
i want this thread to b clean Nd hope u update the op mentioning about the need for unlocked bootloaders..
.
.
.
.
i can still hear few beings barking even after being warned!!
@archies20 I would suggest you to delete this thread and start a new thread with updated OP..
you can see How your thread is being spoiled by few kids...
Am tired of complaining to moderators about these kids..
All the best for your new thread = )
Download links are dead please add new.....
short google url not opening
short google url not opening please help,i want to download the stock rom and i cant
nicely summarised. I flashed stock rom yesterday without any problems at all. Now on 5.1 Phillipines ROM
just one tip : If you want to relock OEM and regain warranty select firmware upgrade option in SP flash tools
not working iam on lollipop
thanx
good work sir keep it up... its working soloution
DOwn ._.
archies20 said:
@mohsin.r.munshi Already Created thread in android development section about stock rom. But he is not mentioned installation method for noobs So I setup new thread.
Hello Developers.
Pre-Requisite:
1. http://goo.gl/aGMN8e
2. http://goo.gl/tczCMx
Downloads:
1. http://goo.gl/79N7u7
Installation Method: [With SP flash tool]
Before proceeding further please make a backup of your device with CWM Recovery or MTKDroid Tools.
Step 1 :- Firstly Download and Install USB Drivers in your PC from the download Section Below.
Step 2 :- Now Download Main ROM Zip and SP Flash Tools.
Step 3 :- After downloading Extract Them Into A Separate Folder into your PC. [Please Turn off Your Anti-Virus During The Process For Some Time.]
Step 4 :- Now Switch-Off You Canvas A1 , Remove Battery & Re-Insert It to Ensure that its Properly Switched Off.
Step 5 :- Next Open SP-Flash Tools From The Same Extracted Folder.
Step 6 :- Now click Click Scatter Loading & Select The ‘MTTK65XX_Scatter.txt‘ From The Directory Where you extracted the Main ROM.
Step 7 :- Hit the Download button and SP Flash Tools will start searching for your device.
Step 8 :- Now connect your device with a USB Cable in the switch off mode.
Step 9 :- Your device will be detected by SP Flash Tools and Upgrade Process will start.
Step 10 :-The process will complete in 3-4 minutes and then a success popup will appear, now disconnect your phone reinsert its battery and power it on.
That’s it, FIrst boot will take about 4-5 minutes wait for it and enjoy stock Experience. :laugh:
And the Phone is as good as new
Click to expand...
Click to collapse
please update the link thy seems to be down
Battery nikla ke flash kar na h??????
Sent from my Micromax AQ4501 using XDA Free mobile app
galileo_24 said:
nicely summarised. I flashed stock rom yesterday without any problems at all. Now on 5.1 Phillipines ROM
just one tip : If you want to relock OEM and regain warranty select firmware upgrade option in SP flash tools
Click to expand...
Click to collapse
Thanks it helped me a lot.
flashing done ....but power on not working ......please help
---------- Post added at 02:04 PM ---------- Previous post was at 02:03 PM ----------
dsk197 said:
please update the link thy seems to be down
Click to expand...
Click to collapse
flashing done ....but power on not working ......please help
Link is not work....plz update link
sonu123456 said:
Link is not work....plz update link
Click to expand...
Click to collapse
here its - LINK TO stock kitkat android one sprout4 rom, flashable via custom recovery
huge thanks to 1cefire .
Port color is pls
Micromax e481 ios ROMs 10 download

micromax canvas a1 stuck on boot animation after rooting (android marshmallow)

i updated my canvas a1 to android marshmallow, after that i rooted my device using android one tool kit after rebooting it is stuck on boot screen animation screen.
please help me
Please provide more detail or just describe what you tried and what happened.
its beacuse android m cant be rooted without flashing custom kernel. it goes into bootloop. so first download thnderzap kernel 3.5.zip , flash it and then download supersu.zip and flash it. then it will 100%work.
How to install custom recovery in a handset that is bootlooping?
Please tell us the procedure
Boot in fastboot mode and flash recovery from there .
aaqib846 said:
i updated my canvas a1 to android marshmallow, after that i rooted my device using android one tool kit after rebooting it is stuck on boot screen animation screen.
please help me
Click to expand...
Click to collapse
STEP 1: DOWNLOAD the FLASH TOOL from this this link :LINK TO DOWNLOAD FILE
It is almost 30 MB in Size. And EXTRACT / UNZIP it to Desktop ( OR SOMEWHERE ) of your computer.
STEP 2: DOWNLOAD LOLLIPOP FLASH FILE
DOWNLOAD LINK FOR LOLLIPOP: HERE
After downloading this flash file EXTRACT / UNZIP it to Desktop ( OR SOMEWHERE ) on your computer.
STEP 3: NOW INSTALL DRIVERS:
YOU NEED TO BE ON WINDOWS 7 TO INSTALL DRIVERS (WINDOWS 8 DOESN'T SUPPORT THIS DRIVER / PHONE IS NOT DETECTED)
DOWNLOAD DRIVERS from this link : HERE
EXTRACT AND INSTALL THE DRIVERS : Next next next and finish If you see an security warning ( a red coloured pop up ) choose INSTALL IT ANYWAY
IT IS RECOMMENDED YOU TO RESTART YOUR PC.
STEP 4:
Now we have Extrated /unziped 2 files. One is FLASHTOOLS and other is FLASH FILE and Extracted it or unziped it to Desktop or Somewhere.
One of it having the name SP_Flash_Tool_exe_windows_v5.1424.00 or open both folders then one of it having the flashing tool. OPEN THE FOLDER NAMED SP_Flash_Tool_exe_windows_v5.1424.00
it contains an application named fashtool.exe OPEN IT
NOW THE APPLICATION IS ASKING FOR SCATTER LOADING FILE
its a txt file which is on the extracted flash file folder
BROWSE it by clicking Button named Scatter Loading
click OPEN
STEP 5:
HERE IN THE DROPDOWN BOX, IT SAYS DOWNLOAD ONLY, CLICK ON IT AND SELECT FIRMWARE UPDATE ONLY.
IF YOU SELECT FORMAT + DOWNLOAD, THEN YOU WILL LOOSE IMEI NUMBER.
NOW CLICK DOWNLOAD BUTTON ( GREEN ARROWED BUTTON NAMED DOWNLOAD )
IN CASE YOU LOOSE IMEI NUMBER, THEN REFER HERE
STEP 6:
Now SWITCH OFF your PHONE and REMOVE BATTERY
STEP 7:
CONNECT your PC via USB CABLE
wait for the driver Detection.
THE FLASHING PROCESS WILL START AUTOMATICALLY you can See the progress in progress bar which is on bottom of flashing tool Application.
WHEN IT IS FINISHED DISCONNECT USB AND RESTART YOUR PHONE.
NOW YOU WILL GET LOLLIPOP UPDATE IMMEDIATELY.
NOW REFER HERE TO ROOT MARSHMALLOW
:good::good:HIT THANKS IF HELPED:good::good:
Hello friend, I followed the steps in above instructions. But after clicking download, nothing happens. I have installed all the drivers but my phone is not detecting when battery is removed. Can you help please ....
Best answer :
aaqib846 said:
i updated my canvas a1 to android marshmallow, after that i rooted my device using android one tool kit after rebooting it is stuck on boot screen animation screen.
please help me
Click to expand...
Click to collapse
Hey dude you can try this awesome way
1st install a custom recovery
2nd download CyanogenMod (avialable cm13 android version 6.0.1) from YouTube or Google
3rd download gapps for android 6 from xda developers
4th boot into recovery mode
5th wipe user data
6th wipe cache partition
7th install zip 1st CM 13
Then 2nd Gapps
8th reboot system now
Enjoy the CM13 official ROM on A1
Root access in Inbuilt
For root access :
1st go to settings
2nd go to about phone
3rd enable developer options by tapping built number 7times
4th back in developer options enable root access.
Enjoy...
canvas a1 stuck at boot animation
i flashed my a1 using sp flash it was successful. but now when i switch on my phone its stuck at animation

[Guide][Marshmallow] Android 6.0 official update for Micromax Canvas A1 (AQ4501)

Update: SPFlashTool flashable Marshmallow firmware file is now available. Build MOB30N.
OTA links are already there on xda, but here was no specific thread for Canvas A1 so i am writing one
Google has released the OTA files for Canvas A1 and other android one devices.
NOTE: To update your phone using OTA files your phone should be running Stock lollipop or atleast stock recovery. (Not applicable if using sp flash tool)
If you are running a custom rom or custom recovery then before proceeding to this guide you must revert back to stock lollipop using sp flash tool
Pre-requisites: 1.Your phone should be atleast 60% charged
2. Back up all important data (just to be safe)
Canvas A1 users can easily update their device by following method(s)
Method 1 (the usual method):
Step 1: Download the official Marshmallow OTA file from here https://android.googleapis.com/packages/ota/google_aq4501sprout_aq4501/dc78fbefaf5f69cc4754751251d9ece094bc96e6.signed-sprout-mmx-MRA58M-from-LMY48M.zip
Step 2: Connect your smartphone to computer using the original USB cable.
Step 3: Copy and paste the OTA zip files to phone's storage and make a note of its location.
Step 4: Boot your smartphone into recovery mode or stock recovery: Disconnect the phone from computer, and then turn it off.
Press and hold both the Volume and the Power buttons until the display turns on and enters bootloader mode.
Hit the volume button to open the Recovery menu and then press the power button to select it. Your phone should now boot into recovery mode.
At this moment, a dead Android with an exclamation mark should appear on the screen. Now press and hold Power button for three seconds and then hit the Volume up button once to progress into recovery mode.
Step 5: Return to the main recovery screen and choose 'install update from sdcard'.
Step 6: Then select the OTA zip file using the volume buttons for navigation and the Power button to select any file or open a folder. After you select the zip file, confirm its installation and the update should start installing on your device.
Step 7: Once the installation is done, return to main screen of recovery. Choose Reboot system now to restart the phone and boot into the newly installed Android 6.0 Marshmallow OTA update from Google.
Voila!! You are running official Android 6.0 :laugh:
Method 2 (using sp flash tool, best method)
This method can be used even if you are running a custom rom. You can also use this method to unbrick Micromax Canvas A1.
Pre-requisites: Windows computer, USB cable, and most important "patience".
Step 1:
a) Download micromax driver.{thanks to @mohsin.r.munshi}
Extract its content, you will find an .exe file inside a folder "driver9401". Disable your antivirus and run the .exe file as administrator. (If you are using 64-bit windows, you will need to "disable driver signature enforcement". Google it)
b) Download SP Flash tool from my mediafire or from its official website. Extract it to any folder
c) Download SPflashTool flashable Marshmallow firmware . Extract the zip file. You will see the following files in it (similar not exact)
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Note the location of MT6582_Android_scatter.txt file
Step2: Goto the folder where you have extracted sp flash tool. Run flash_tool.exe
Step 3: In sp flash tool, Click on "scatter loading". Then locate and select "MT6582_Android_scatter.txt". SP Flash tool will load all firmware files from the folder where you have extracted the OTA files.
Step 4: Power off your phone. And REMOVE the battery. Now on SP flash tool, click on "Download".
(refer to screenshots given on this website. Ignore the steps given on this website, just refer screenshots)
Step 5: (pay attention to every word) Connect USB cable to your phone only. Then Press and HOLD volume down button and insert the other end of USB cable to your pc. Flashing will start automatically. Wait till you see "OK" message on your pc.
Step 6: Once you see "OK" message, disconnect your phone and reinsert your phone's battery. Turn ON your phone. The first boot will take longer than usual.
Congo! You just updated/unbricked your Micromax Canvas A1.
Feel free to post comments for any doubts and errors
My canvas a1 software has been damaged, and it shows an error while installing update from sd card , so how do I can solve this problem ???? Please reply fast........
gd5121995 said:
My canvas a1 software has been damaged, and it shows an error while installing update from sd card , so how do I can solve this problem ???? Please reply fast........
Click to expand...
Click to collapse
flash official lollipop rom using method 2 above
Hi.. I'm on CM13 now. But I don't have mobile data for some reason. So I want to flash stock ROM. But last time I tried flashing stock, it wiped my IMEI numbers. Luckily my warranty status was somehow reset. So I had to get the phone replaced. Does this have a chance to cause the same problem (wipe my IMEI numbers)??
GughanRk said:
Hi.. I'm on CM13 now. But I don't have mobile data for some reason. So I want to flash stock ROM. But last time I tried flashing stock, it wiped my IMEI numbers. Luckily my warranty status was somehow reset. So I had to get the phone replaced. Does this have a chance to cause the same problem (wipe my IMEI numbers)??
Click to expand...
Click to collapse
sp flastool wipes userdata only, you wont loose your imei using spft.
sziraqui said:
sp flastool wipes userdata only, you wont loose your imei using spft.
Click to expand...
Click to collapse
Realy sorry to say this, but I lost my IMEI using SP Flashtools only. Check this thread.. There are a lot of other users facing the same problem.
And SN Write Tool method didn't help me get my IMEI back.. So I want to be really sure before flashing this time
recover imei android one....
try this...worked for my spice android one (mi-498)
http://forum.xda-developers.com/cro...lashable-zip-imei-repair-android-one-t2992846
GughanRk said:
Realy sorry to say this, but I lost my IMEI using SP Flashtools only. Check this thread.. There are a lot of other users facing the same problem.
And SN Write Tool method didn't help me get my IMEI back.. So I want to be really sure before flashing this time
Click to expand...
Click to collapse
In that case, i would suggest you to take a backup of your imei data using MTK Droid tool. Also copy your nvram folder straight from your phone to as many external storages as you can. Nvram (imei data) somehow becomes unrecognised after downgrading some phones.
Solution:
1. Use MTK droid tool to restore it from a previous backup.
or
2. locate nvram folder ( /data/nvram, correct me if i m wrong) DELETE it. Then paste a copy of your nvram folder that you copied when imei was not lost. DONT chmod. You will most probably get your network working (ensure that sim card was PRSENT and Radios were ON during this copy paste) within few seconds. I did this to restore imei on galaxy s4.
well, i have flashed 9 different mediatek phones using spflashtool, didnt lose imei in any.
sziraqui said:
In that case, i would suggest you to take a backup of your imei data using MTK Droid tool. Also copy your nvram folder straight from your phone to as many external storages as you can. Nvram (imei data) somehow becomes unrecognised after downgrading some phones.
Solution:
1. Use MTK droid tool to restore it from a previous backup.
or
2. locate nvram folder ( /data/nvram, correct me if i m wrong) DELETE it. Then paste a copy of your nvram folder that you copied when imei was not lost. DONT chmod. You will most probably get your network working (ensure that sim card was PRSENT and Radios were during this copy paste) within few seconds. I did this to restore imei on galaxy s4.
well, i have flashed 9 different mediatek phones using spflashtool, didnt lose imei in any.
Click to expand...
Click to collapse
Thanks! I'll post an update when I come around to flashing the stock ROM. Don't have the time now.
hi can i use these update for micromax unite2(8gb) from lolipop to marshmallow.
Firmwares are device specific. You CANNOT install a this on any other phone. You will brick your phone by installing a ROM which is not made for your device
Please update stock marshmallow link sir as soon as possible
.......
Thanks in advance
Micromax android one got hang at marshmallow logo.
My micromax android one got stuck at marshmallow logo. I tried to flash lollipop using SP flash as mention above in method 2. I connect my phone . My phone is successfully detected by my PC. But SP flash show no progress. why??? I follow all steps very carefully. Or is it not possible to install lollipop if your phone already has marshmallow?
ravipreet23 said:
My micromax android one got stuck at marshmallow logo. I tried to flash lollipop using SP flash as mention above in method 2. I connect my phone . My phone is successfully detected by my PC. But SP flash show no progress. why??? I follow all steps very carefully. Or is it not possible to install lollipop if your phone already has marshmallow?
Click to expand...
Click to collapse
That means your phone was not detected. Power off your phone. Load scatter file and then click on download button on so flashtool. Put one end of USB cable to your phone. Hold volume down and simultaneously put other end of USB cable to computer. If its connected, the progress bar at bottom will show progress. I am assuming you have installed all drivers.
I hope this helps.
ravipreet23 said:
My micromax android one got stuck at marshmallow logo. I tried to flash lollipop using SP flash as mention above in method 2. I connect my phone . My phone is successfully detected by my PC. But SP flash show no progress. why??? I follow all steps very carefully. Or is it not possible to install lollipop if your phone already has marshmallow?
Click to expand...
Click to collapse
That means your phone was not detected. Power off your phone. Load scatter file and then click on download button on so flashtool. Put one end of USB cable to your phone. Hold volume down and simultaneously put other end of USB cable to computer. If its connected, the progress bar at bottom will show progress. I am assuming you have installed all drivers.
I hope this helps.
sziraqui said:
That means your phone was not detected. Power off your phone. Load scatter file and then click on download button on so flashtool. Put one end of USB cable to your phone. Hold volume down and simultaneously put other end of USB cable to computer. If its connected, the progress bar at bottom will show progress. I am assuming you have installed all drivers.
I hope this helps.
Click to expand...
Click to collapse
I have installed all drivers as my pc detect my mobile as i can see in device manager. I perform all steps that you mention but SP flash player show nothings. CAn you tell me can i flash Lollipop stock rom on my android one which is running marshmallow previously. I cant find marshmallow stock rom thats why i have to flash lollipop stock rom??
sziraqui said:
OTA links are already there on xda, but here was no specific thread for Canvas A1 so i am writing one
Google has released the OTA files for Canvas A1 and other android one devices.
NOTE: To update your phone using OTA files your phone should be running Stock lollipop or atleast stock recovery. (Not applicable if using sp flash tool)
If you are running a custom rom or custom recovery then before proceeding to this guide you must revert back to stock lollipop using sp flash tool
Pre-requisites: 1.Your phone should be atleast 60% charged
2. Back up all important data (just to be safe)
Canvas A1 users can easily update their device by following method(s)
Method 1 (the usual method):
Step 1: Download the official Marshmallow OTA file from here https://android.googleapis.com/packages/ota/google_aq4501sprout_aq4501/dc78fbefaf5f69cc4754751251d9ece094bc96e6.signed-sprout-mmx-MRA58M-from-LMY48M.zip
Step 2: Connect your smartphone to computer using the original USB cable.
Step 3: Copy and paste the OTA zip files to phone's storage and make a note of its location.
Step 4: Boot your smartphone into recovery mode or stock recovery: Disconnect the phone from computer, and then turn it off.
Press and hold both the Volume and the Power buttons until the display turns on and enters bootloader mode.
Hit the volume button to open the Recovery menu and then press the power button to select it. Your phone should now boot into recovery mode.
At this moment, a dead Android with an exclamation mark should appear on the screen. Now press and hold Power button for three seconds and then hit the Volume up button once to progress into recovery mode.
Step 5: Return to the main recovery screen and choose 'install update from sdcard'.
Step 6: Then select the OTA zip file using the volume buttons for navigation and the Power button to select any file or open a folder. After you select the zip file, confirm its installation and the update should start installing on your device.
Step 7: Once the installation is done, return to main screen of recovery. Choose Reboot system now to restart the phone and boot into the newly installed Android 6.0 Marshmallow OTA update from Google.
Voila!! You are running official Android 6.0 :laugh:
Method 2 (using sp flash tool, best method)
This method can be used even if you are running a custom rom. You can also use this method to unbrick Micromax Canvas A1.
Pre-requisites: Windows computer, USB cable, and most important "patience".
Step 1:
a) Download micromax driver.{thanks to @mohsin.r.munshi}
Extract its content, you will find an .exe file inside a folder "driver9401". Disable your antivirus and run the .exe file as administrator. (If you are using 64-bit windows, you will need to "disable driver signature enforcement". Google it)
b) Download SP Flash tool from my mediafire or from its official website. Extract it to any folder
c) Extract the the contents of factory image. [Edit: sp flashtool flashable Android 6.0 is currently not available. I 'll add a link as soon as it is available. I wrote this too early, sorry. For now, if you are running a custom rom, flash official lollipop first and then use method 1 to update to marshmallow.].You will see the following files in it.
Note the location of MT6582_Android_scatter.txt
Step2: Goto the folder where you have extracted sp flash tool. Run flash_tool.exe
Step 3: In sp flash tool, Click on "scatter loading". Then locate and select "MT6582_Android_scatter.txt". SP Flash tool will load all firmware files from the folder where you have extracted the OTA files.
Step 4: Power off your phone. And REMOVE the battery. Now on SP flash tool, click on "Download".
(refer to screenshots given on this website. Ignore the steps given on this website, just refer screenshots)
Step 5: (pay attention to every word) Connect USB cable to your phone only. Then Press and HOLD volume down button and insert the other end of USB cable to your pc. Flashing will start automatically. Wait till you see "OK" message on your pc.
Step 6: Once you see "OK" message, disconnect your phone and reinsert your phone's battery. Turn ON your phone. The first boot will take longer than usual.
Congo! You just updated/unbricked your Micromax Canvas A1.
Feel free to post comments for any doubts and errors
Click to expand...
Click to collapse
BROM error : S_FT_DOWNLOAD_FAIL[4008]
Download to flash fail. Please press ctrl +alt +T to turn on debug log then reproduce again.
Hint- BROM_DLL_V5.log and BROM_DLL.log would be created and record more detail information.
It is showing this error what should i do.?
please reply fast sir.
MayankGupta said:
BROM error : S_FT_DOWNLOAD_FAIL[4008]
Download to flash fail. Please press ctrl +alt +T to turn on debug log then reproduce again.
Hint- BROM_DLL_V5.log and BROM_DLL.log would be created and record more detail information.
It is showing this error what should i do.?
please reply fast sir.
Click to expand...
Click to collapse
I can help you if you provide me more details.
Which phone model you were dealing with? Which rom it it was running before? What were you exactly trying to achieve? Also if possible post the log files here.
xposed
can i have xposed for cm13 marshmallow ?
---------- Post added at 05:34 PM ---------- Previous post was at 04:41 PM ----------
can i have xposed for cm13 marshmallow ?
KadirDvl said:
can i have xposed for cm13 marshmallow ?
---------- Post added at 05:34 PM ---------- Previous post was at 04:41 PM ----------
can i have xposed for cm13 marshmallow ?
Click to expand...
Click to collapse
Yes there are xposed for MM.. Just google it.
[url]http://forum.xda-developers.com/xposed/discussion-xposed-marshmallow-t3249095 [/url]
Sent from my sprout4 using XDA Labs

Guide to check and change fingerprint from CN to WW with final Android 9 1910.64 RAW

FIrst off many thanks to @vhercastillojr (as this thread is essentially his) and Chicken from the Vietnam telegram group for providing the RAW's/img's
********** DO THIS AT YOUR OWN RISK!!! I am not liable to any damage if you accidentally brick your device. This will void your warranty, if you had one. Also, using this method you won't be able to revert back to CN roms, lock your bootloader again and recieve OTAs, your device will be blacklisted by Asus ************
NOTE: To check your current fingerprint, download and install device info HW from the playstore. Under 'system' you'll find the current rom (CN or WW), the product id and fingerprint - they all need to match to be able to update your device later
NOTE 2: The main guide below skips early roms straight to last Android 9 for ROG II. For one user it didn't work and they had to use the previous, unedited guide which was based on 1910.35 RAW. If the below guide fails to update follow the additional guide at the end of this post.
----------
0) Download the ROG phone unlock tool and copy it on your phone and install it then run it. The phone will boot twice. DO NOT PRESS POWER TO STOP THE BOOT. It will wipe your data automatically. This will unlock your bootloader. EDIT: NEWER VERSION OF THE TOOL CAN BE FOUND here
NOTE: this will void your warranty, if you had one, with Asus, even if you re-lock your bootloader later... (Although, having bought mine as an import from China, I'm think the warranty only stands with the seller - in my case, 1 year, not Asus - but i may be wrong)
1) Download the WW International RAW rom from here
2) Extract the file on your PC. Boot the phone into fastboot mode (hold volume up then press and hold power button, Fastboot mode is the 1st screen you come across, the one with the options to Start, boot to recovery, etc...) connect to the side port and run "flashall_AFT.cmd" wait for it to finish and the phone will restart itself (it will take a number of minutes to complete, with the cmd window open all the time. If the cmd window only flashes up and closes down, then check the rest of the notes with this step).
NOTE: you need to remove or delete the original zip from the raw folder once extracted as it confuses the Flashall_AFT.cmd with the raw rom and zip having the same name. Also, it can help to extract to the root of C drive.
3) Download and install Minimal ADB and Fastboot app (windows). Install it on your PC to root of C drive
4) Download the rootww191064.img and place it in the Minimal ADB and Fastboot Folder (C:\Program Files (x86)\Minimal ADB and Fastboot) from here
5) Run Minimal ADB and Fastboot by double clicking ''cmd-here.exe''. Switch the phone into fastboot mode (hold volume up then press and hold power button) then type "fastboot flash boot rootww191064.img" without quotation marks
NOTE: you can also check your device is recognised in fastboot mode by the pc/laptop by running ''fastboot devices'' cmd which should show your device serial
6) Reboot the phone and connect it to PC, copy and install Magisk and Root Explorer
Magisk
root explorer
-run magisk, (update if necessary) and grant access to root explorer (after opening root explorer you should be prompted by magisk to gain root access, click 'allow')
7) Open the Root Explorer App on you phone. Then from the app, select Mount R/W to R/O. Search for "/vendor/factory" folder and Edit the file content COUNTRY from CN to WW (ALL Capital). Scroll to "/system/etc/AsusTheme/themes" then delete the hidden file to enable the hidden themes.
8) Restart the Phone. You are done. Check again with device info HW that your fingerprint has indeed been successfully changed.
From here, if you want to be on latest Android 10, download version 2004.60 from here (full zip), place it in root of internal storage and reboot. That'll bring you to A10.
NOTE: For those of you that are rooted: Download the full zip, move to root of internal storage and reboot. System will detect and prompt to update, click update. Wait until it finishes but DON'T click 'restart', instead, click 'restart later'. Go to Magisk manager. Click 'install' for Magisk. Click the last option 'install to inactive slot after OTA'. Click confirm force flash. Reboot when prompted. Done - root kept intact.
Repeat the process for latest (currently 2012.65) using the same link above. Your phone should hopefully skip the other versions and be straight to latest. If not, you'll have to go through 2007.27, 2009.49 and finally to current latest 2012.65. Repeat the process mentioned above for keeping root if so desired
----------
For anyone still running early roms that 1910.64 won't flash directly to, use the same guide above but with the following corrections:
2) Follow the exact same instructions but using this 1910.35 RAW
4) Download root and stock boot img's and extract them to Minimal ADB and Fastboot Folder (C:\Program Files (x86)\Minimal ADB and Fastboot)
5) Run Minimal ADB and Fastboot by double clicking ''cmd-here.exe''. Switch the phone into fastboot mode (hold volume up then press and hold power button) then type "fastboot flash boot rootww191035.img" without quotation marks
NOTE: you can also check your device is recognised in fastboot mode by the pc/laptop by running ''fastboot devices'' cmd which should show your device serial
After doing the ammended steps above for 1910.35, follow the rest of the guide to change fingerprint, then update to 1910.64 zip, place it in root of internal storage and reboot.
NOTE: For those of you that are rooted: Download the full zip, move to root of internal storage and reboot. System will detect and prompt to update, click update. Wait until it finishes but DON'T click 'restart', instead, click 'restart later'. Go to Magisk manager. Click 'install' for Magisk. Click the last option 'install to inactive slot after OTA'. Click confirm force flash. Reboot when prompted. Done - root kept intact.
******************* Thanks to @Barbatos19, who suggested I make video. Sorry to say I wont be, BUT several of you guys have recommended THIS VIDEO as a good reference guide... Hope it helps some others *******************
Finally(!!!), apologies that this post has become cluttered with instructions, I have tried to cater for all you and all eventualities!! Good luck
Thanks for this guide bro. Fully converted from CN to WW.
It wilk work if i have now flashed WW rom but with CN fingerprint? It was like this when i bought from GearBest
Zdrpkamil said:
It wilk work if i have now flashed WW rom but with CN fingerprint? It was like this when i bought from GearBest
Click to expand...
Click to collapse
Which rom version are running, if it's already 1910.35 then you can skip the flashing rom part. But if it's different, you need to follow each step
reg66 said:
Which rom version are running, if it's already 1910.35 then you can skip the flashing rom part. But if it's different, you need to follow each step
Click to expand...
Click to collapse
1906.19
Zdrpkamil said:
1906.19
Click to expand...
Click to collapse
You need to follow each step then
reg66 said:
You need to follow each step then
Click to expand...
Click to collapse
Ok, thanks. I'll do it at weekend and tell if works
what to do when the phone gets stuck on bootloop after flashing rootww191035.img and holding the power button doesnt work either?
Spawn_Ishan said:
what to do when the phone gets stuck on bootloop after flashing rootww191035.img and holding the power button doesnt work either?
Click to expand...
Click to collapse
Edit; didn't realise you were at this stage... Are you sure the flashing of the raw rom worked OK? Did you a cmd window open for a good 5-10 mins while the rom flashed?
Will KingRoot app work to root this phone? Don't want to have to wipe data to root.
I am pretty sure it won't, but humor me. Or is their something else out there that works?
jkeener88 said:
Will KingRoot app work to root this phone? Don't want to have to wipe data to root.
Click to expand...
Click to collapse
No idea... But im doubtful
hi bro
your link unlock tool its 190702..i can use it?
my rom ww1908.12 with finger CN
your file link name in step 4 is not same and file name is step 5..
its a same file to use?step 4 name boot&rootww and step 5 file ne to use rootww..do need to rename file step 4 to rootww?
and u have link l file to unroot 191035?
thx bro
wilsen1985 said:
hi bro
your link unlock tool its 190702..i can use it?
my rom ww1908.12 with finger CN
your file link name in step 4 is not same and file name is step 5..
its a same file to use?step 4 name boot&rootww and step 5 file ne to use rootww..do need to rename file step 4 to rootww?
and u have link l file to unroot 191035?
thx bro
Click to expand...
Click to collapse
One moment, I'll check the links... And yes, that is the only unlock tool available from asus website...
EDIT: yes, the zip file to download in step 4 needs to be extracted. it contains both the root boot img and stock img for later on when you unroot etc (both root and stock boot img's are for 1910.35). you need to place the rootww191035.img in the same folder as adb... and do the same for the stock boot.img for later use... read the instructions carefully...
reg66 said:
One moment, I'll check the links... And yes, that is the only unlock tool available from asus website...
Click to expand...
Click to collapse
i can't find link unroot 191035..
do u have thats link?
wilsen1985 said:
i can't find link unroot 191035..
do u have thats link?
Click to expand...
Click to collapse
in step 4) you download a .zip file that conatins BOTH rootww191035.img AND boot.img - the boot.img IS the stock boot for unrooting 1910.35, you need to extract both img's to adb folder on your pc.
reg66 said:
One moment, I'll check the links... And yes, that is the only unlock tool available from asus website...
EDIT: yes, the zip file to download in step 4 needs to be extracted. it contains both the root boot img and stock img for later on when you unroot etc (both root and stock boot img's are for 1910.35). you need to place the rootww191035.img in the same folder as adb... and do the same for the stock boot.img for later use... read the instructions carefully...
Click to expand...
Click to collapse
oh ok thx bro
1 question again
yesterday i download file raw ww1910.35 zip on asus website
can i use its raw file to this tutor or must download raw file in page 1?
wilsen1985 said:
oh ok thx bro
1 question again
yesterday i download file raw ww1910.35 zip on asus website
can i use its raw file to this tutor or must download raw file in page 1?
Click to expand...
Click to collapse
What you downloaded is not, I think, the raw rom, its the update zip for those who have already changed fingerprint and are simply updating... Please use the links in 1st page...
reg66 said:
What you downloaded is not, I think, the raw rom, its the update zip for those who have already changed fingerprint and are simply updating... Please use the links in 1st page...
Click to expand...
Click to collapse
oh ok bro
i download raw in page 1 n when its complete i start for flash..
hope im succes for all convert
thx bro..
wilsen1985 said:
oh ok bro
i download raw in page 1 n when its complete i start for flash..
hope im succes for all convert
thx bro..
Click to expand...
Click to collapse
Good luck, make sure you read it all and follow each step accurately
reg66 said:
Good luck, make sure you read it all and follow each step accurately
Click to expand...
Click to collapse
ok bro very thx..

Categories

Resources