Related
Guys today I tried installing MIUI v4. I followed all the steps mentioned in the thread. I installed everything properly but my phone is stuck onthe android logo. This happened when I rebooted my phone after installing MIUI. So please tell me what is the problem. Also when I am truing to restore some type of error is cropping up. Please help.
pranjaldixit said:
Guys today I tried installing MIUI v4. I followed all the steps mentioned in the thread. I installed everything properly but my phone is stuck onthe android logo. This happened when I rebooted my phone after installing MIUI. So please tell me what is the problem. Also when I am truing to restore some type of error is cropping up. Please help.
Click to expand...
Click to collapse
Before installing make backup wipe dalvik cache , cache, do factory reset and try again .. hope it helps
Sent from my Hero using xda premium
Actually I tell the whole story now. When I was making backup of my stock ROM the sd card showed low on space. So I removed that SD card and inserted the one which came with the Phone. On that I installed all the required zip files. Then I made backup of the stock ROM and the data. After that I followed these steps mentioned here -:
http://forum.xda-developers.com/showthread.php?t=1863260
According to the steps I did not did wipe davik cache etc. after instaling the ROM I did wipe factory and data reset and wipe cache partition. After following all the steps mentioned I rebooted my phone as mentioned. But after rebooting the phone is stuck on android logo. I then again went into recovery and tried to wipe dalvik cache the confirmation page that appears before wiping anything is not coming. Also when I tried to restore my phone to the stock ROM an error message is coming. So I am not able to restore to the stock ROM. This is the whole thing. So guys please help. I hope I have not bricked my phone. Any solutions?
Thanks
As long as your phone can go to recovery mode it wasnt bricked..
May i know what recovery that you use to install the rom??
Sent from my GT-S5660 using Tapatalk 2
AiphNday said:
As long as your phone can go to recovery mode it wasnt bricked..
May i know what recovery that you use to install the rom??
Sent from my GT-S5660 using Tapatalk 2
Click to expand...
Click to collapse
Mate I used latest version of ClockWork Mod to install the ROM.
pranjaldixit said:
Mate I used latest version of ClockWork Mod to install the ROM.
Click to expand...
Click to collapse
What version it is??
If you are install custom rom from stock rom,its better to use px-cwmV2..
If test it,and it minimize the risk of stuck on android logo..
After that you can change the recovery to other version that you want..
Sent from my GT-S5660 using Tapatalk 2
AiphNday said:
What version it is??
If you are install custom rom from stock rom,its better to use px-cwmV2..
If test it,and it minimize the risk of stuck on android logo..
After that you can change the recovery to other version that you want..
Sent from my GT-S5660 using Tapatalk 2
Click to expand...
Click to collapse
I think the version is 5.0.2.7. Also when I am switching off the phone after sometime it is automatically switching on by itself. So for the time being I have removed the battery.
pranjaldixit said:
I think the version is 5.0.2.7. Also when I am switching off the phone after sometime it is automatically switching on by itself. So for the time being I have removed the battery.
Click to expand...
Click to collapse
If you use that version,use the version that can support rfs+ext4 file system..
Stock rom use rfs file system and custom rom usually use ext4 file system,so therefore you have to use recovery that support both..
Sent from my GT-S5660 using Tapatalk 2
AiphNday said:
If you use that version,use the version that can support rfs+ext4 file system..
Stock rom use rfs file system and custom rom usually use ext4 file system,so therefore you have to use recovery that support both..
Sent from my GT-S5660 using Tapatalk 2
Click to expand...
Click to collapse
Could you please tell me how to proceed? Because the backup of stock ROM is showing problems.
pranjaldixit said:
Could you please tell me how to proceed? Because the backup of stock ROM is showing problems.
Click to expand...
Click to collapse
I suggest that you flash your phone to stock rom again via odin..
Then change your recovery,i was preffered px-cwmV2,but i dont know is the link still alive or not..
Flash the recovery,reboot..
Then enter recovery mode again,install rom..
Sent from my GT-S5660 using Tapatalk 2
How to do flash stock ROM as the backup that I made is not working properly.
pranjaldixit said:
How to do flash stock ROM as the backup that I made is not working properly.
Click to expand...
Click to collapse
With odin,
Search ! there are allot of guide howto flash gio to stock with odin
Sent from my HTC Hero using xda app-developers app
If you have working recovery it's no use to flash stock ROM, just flash px-cwmV2 http://www.mediafire.com/file/y1xy6g2y5tpp1fg/px-cwm-v2.zip.
Then wipe all, including dalvik, flash desired ROM, wipe all again (including dalvik), and you should be good to go.
phreak_or said:
If you have working recovery it's no use to flash stock ROM, just flash px-cwmV2 http://www.mediafire.com/file/y1xy6g2y5tpp1fg/px-cwm-v2.zip.
Then wipe all, including dalvik, flash desired ROM, wipe all again (including dalvik), and you should be good to go.
Click to expand...
Click to collapse
I hope you must have read my post about the problem. I have clockwork 5.0.2.7. The backup I made is alao showing some error when I tried to restore it using CWM. So please guide how to proceed.
pranjaldixit said:
I hope you must have read my post about the problem. I have clockwork 5.0.2.7. The backup I made is alao showing some error when I tried to restore it using CWM. So please guide how to proceed.
Click to expand...
Click to collapse
I have. As i said, you could just try CWM v2.
BUT to be absolutely safe flash a stock ROM using Odin, see http://forum.xda-developers.com/showpost.php?p=20397915&postcount=3.
After u flash the stock ROM, go to default recovery, factory reset, boot the rom, shutdown.
Flash the desired version of CWM using Odin or trough recovery, and then flash the custom ROM u want.
For me CWM 5.0.2.7 ext4+ RFS couldn't wipe dalvik, nor could it mount /system. So I used cwmV2.
Good luck!
phreak_or said:
I have. As i said, you could just try CWM v2.
BUT to be absolutely safe flash a stock ROM using Odin, see http://forum.xda-developers.com/showpost.php?p=20397915&postcount=3.
After u flash the stock ROM, go to default recovery, factory reset, boot the rom, shutdown.
Flash the desired version of CWM using Odin or trough recovery, and then flash the custom ROM u want.
For me CWM 5.0.2.7 ext4+ RFS couldn't wipe dalvik, nor could it mount /system. So I used cwmV2.
Good luck!
Click to expand...
Click to collapse
Thanks a lot. So first I have to download firmware and then using odin flash it on my phone. After that I have to install clockworkmod v2 amd then install the MIUI ROM? Can the CWM be flashed through recovery?
Thanks
pranjaldixit said:
Thanks a lot. So first I have to download firmware and then using odin flash it on my phone. After that I have to install clockworkmod v2 amd then install the MIUI ROM? Can the CWM be flashed through recovery?
Thanks
Click to expand...
Click to collapse
yes
And please tell me how to install CWM v2 as I already have version 5.0.2.7 of clockwork mod installed in my phone? Pease let me know the procedure for the same.
Thanks
pranjaldixit said:
And please tell me how to install CWM v2 as I already have version 5.0.2.7 of clockwork mod installed in my phone? Pease let me know the procedure for the same.
Thanks
Click to expand...
Click to collapse
when you flash firmware with odin, it will also flash a new recovery.
just enter recovery like normally, and flash cwm-v2.zip
after its done you pull the battery out, and boot into recovery again.
now you have clockworkmod installed
voetbalremco said:
when you flash firmware with odin, it will also flash a new recovery.
just enter recovery like normally, and flash cwm-v2.zip
after its done you pull the battery out, and boot into recovery again.
now you have clockworkmod installed
Click to expand...
Click to collapse
I am not installing firmware right now. I am just wanting to install CWM v2 and try whether it is able to install MIUI successfully or not. If this one also fails then I will install the firmwares via odin. Hope you ate able to understand what I am saying. Please help.
Dear friends ... I have a big problem with my P601 Tablet ... my problem :
I were having problem with my nand memory so I managed to flash a ROM with having the " Wipe NAND all " ticked in Odin and after that I found that the phone wont boot so I thought it might be from the bootloader and updated the bootloader to KK and now I can't get my tablet to even boot android and also I can't mount /data in recovery to boot a custom ROM... is there any solution for me ? ... is there any way to get that JB firmware flashed on my tab ? ( to get 4.3. ROM on it to see if it might boot )... is there any way to even boot the android to pick my files ? ... thanks in advance ...
With Best Wishes
Hitman1376
hitman1376 said:
Dear friends ... I have a big problem with my P601 Tablet ... my problem :
I were having problem with my nand memory so I managed to flash a ROM with having the " Wipe NAND all " ticked in Odin and after that I found that the phone wont boot so I thought it might be from the bootloader and updated the bootloader to KK and now I can't get my tablet to even boot android and also I can't mount /data in recovery to boot a custom ROM... is there any solution for me ? ... is there any way to get that JB firmware flashed on my tab ? ( to get 4.3. ROM on it to see if it might boot )... is there any way to even boot the android to pick my files ? ... thanks in advance ...
With Best Wishes
Hitman1376
Click to expand...
Click to collapse
OK, since you already flashed KK bootloader, then you have no choice but flash STOCK 4.4 rom. This should fixed your issue and it's too late to go back to 4.3.
buhohitr said:
OK, since you already flashed KK bootloader, then you have no choice but flash STOCK 4.4 rom. This should fixed your issue and it's too late to go back to 4.3.
Click to expand...
Click to collapse
Thanks for the reply man ... but my problem is that the stock ROM doesn't boot and also in the recovery the /data partition can't be mounted to install a custom ROM ...
Edit : I have installed and have mount / data Problem ... any idea ?
With best Wishes
Hitman1376
hitman1376 said:
Thanks for the reply man ... but my problem is that the stock ROM doesn't boot and also in the recovery the /data partition can't be mounted to install a custom ROM ...
With best Wishes
Hitman1376
Click to expand...
Click to collapse
Do you have TWRP custom recovery or can you install it if you don't have it?
buhohitr said:
Do you have TWRP custom recovery or can you install it if you don't have it?
Click to expand...
Click to collapse
Sure ... I'll install in a minute ... why ?
hitman1376 said:
Sure ... I'll install in a minute ... why ?
Click to expand...
Click to collapse
OK, let take it slowly, you still have stock recovery right? use it to wipe data and cache, then power off then boot back into recovery see if you can mount sdcard
buhohitr said:
OK, let take it slowly, you still have stock recovery right? use it to wipe data and cache, then power off then boot back into recovery see if you can mount sdcard
Click to expand...
Click to collapse
I should reflash the stock ROM to get stock recovery ?
hitman1376 said:
I should reflash the stock ROM to get stock recovery ?
Click to expand...
Click to collapse
what do you have as recovery? twrp or cwm? also tell me the version.
buhohitr said:
what do you have as recovery? twrp or cwm? also tell me the version.
Click to expand...
Click to collapse
Well ... I had TWRP 2.7 and Philz 2.6.3 ( in both couldn't mount /data ) but now I'm flashing the stock firmware to get stock recovery ... in SD I have the TWRP 2.7's zip ...
Edit : I have installed the stock recovery and now this recovery also has " Can't mount /data " problem ...
hitman1376 said:
Well ... I had TWRP 2.7 and Philz 2.6.3 ( in both couldn't mount /data ) but now I'm flashing the stock firmware to get stock recovery ... in SD I have the TWRP 2.7's zip ...
Edit : I have installed the stock recovery and now this recovery also has " Can't mount /data " problem ...
Click to expand...
Click to collapse
Did you wipe data and cache, power off then boot back into recovery and check?
buhohitr said:
Did you wipe data and cache, power off then boot back into recovery and check?
Click to expand...
Click to collapse
Man ... This sounds like magic ......... Yessss ... the /data error is gone !!!!!!!! ..... So , What next ?
hitman1376 said:
Man ... This sounds like magic ......... Yessss ... the /data error is gone !!!!!!!! ..... So , What next ?
Click to expand...
Click to collapse
Use Odin and reflash stock 4.4 kitkat rom, leave everything as default and use AP mode to load the firmware.
buhohitr said:
Use Odin and reflash stock 4.4 kitkat rom, leave everything as default and use AP mode to load the firmware.
Click to expand...
Click to collapse
Sure ... I'll do it in a minute ...
hitman1376 said:
Sure ... I'll do it in a minute ...
Click to expand...
Click to collapse
Make sure use Odin 3.09 version.
Thanks ..................
buhohitr said:
Make sure use Odin 3.09 version.
Click to expand...
Click to collapse
Dear friend ... Thats Amazing ... I should thank you for all the things I learned from you ... Man , Wsh you a healthy wealthy life full of success ... you helped me out of this problem and I'll start my work to get wake gestures to this device helping the xluco ... Great thianks again ...
With best Wishes
Hitman1376
I am using Spice Dream Uno. I decided to install cm11 sprout ROM but it says that it is a bad zip. Then i tried this
http://forum.xda-developers.com/dream-uno/development/stock-rom-spice-dream-uno-mi498-t2915844 (Stock Rom for Android one)
still stuck on boot animation of Micromax
How to make my phone completely working.
PLEASE HELP
Rishabh-The Developer said:
I am using Spice Dream Uno. I decided to install cm11 sprout ROM but it says that it is a bad zip. Then i tried this
http://forum.xda-developers.com/dream-uno/development/stock-rom-spice-dream-uno-mi498-t2915844 (Stock Rom for Android one)
still stuck on boot animation of Micromax
How to make my phone completely working.
PLEASE HELP
Click to expand...
Click to collapse
solution for bad zip :
fine.. u must hav unlocked bootloader, rooted and custom recovery like cwm 6.0.4.x..
if its ok then verify your downloaded zip
..
this can be done by double clicking it on windows or in your mobile use file explorer..
if the zip contains meta-inf folder, system, boot. img.. then your download was good.. otherwise re download it..
solution for boot stuck :
did u replace oem and boot logo of mmx with spice?
try it and report..
or just flash the oem nd boot logo alone
Faiyaz5yaz said:
fine.. u must hav unlocked bootloader, rooted and custom recovery like cwm 6.0.4.x..
if its ok then verify your downloaded zip
..
this can be done by double clicking it on windows or in your mobile use file explorer..
if the zip contains meta-inf folder, system, boot. img.. then your download was good.. otherwise the re download it..
if again everything was perfect as mentioned above.. report it again here
Click to expand...
Click to collapse
my oem is unlocked, rooted mobile and have cwm 6.0.4
how to make my phone completely working ??
how to intall a stock rom or any other rom on my phone through cwm??
cwm shows error everytime when i install cm11 zip
Rishabh-The Developer said:
my oem is unlocked, rooted mobile and have cwm 6.0.4
how to make my phone completely working ??
how to intall a stock rom or any other rom on my phone through cwm??
cwm shows error everytime when i install cm11 zip
Click to expand...
Click to collapse
i hav edited my previous post.. check it again
Faiyaz5yaz said:
i hav edited my previous post.. check it again
Click to expand...
Click to collapse
ok wait let me flash these two.
Still Stucked
Faiyaz5yaz said:
solution for bad zip :
fine.. u must hav unlocked bootloader, rooted and custom recovery like cwm 6.0.4.x..
if its ok then verify your downloaded zip
..
this can be done by double clicking it on windows or in your mobile use file explorer..
if the zip contains meta-inf folder, system, boot. img.. then your download was good.. otherwise re download it..
solution for boot stuck :
did u replace oem and boot logo of mmx with spice?
try it and report..
or just flash the oem nd boot logo alone
Click to expand...
Click to collapse
I Replaced boot logo and Oem but still I Stuck on Boot Animation of Spice.
I Really don't know much about this phone. Please tell me a Working Method to solve my issue.
I want my Phone Working only. No Matter how but need it badly.
Rishabh-The Developer said:
I Replaced boot logo and Oem but still I Stuck on Boot Animation of Spice.
I Really don't know much about this phone. Please tell me a Working Method to solve my issue.
I want my Phone Working only. No Matter how but need it badly.
Click to expand...
Click to collapse
check if recovery is working or flash a custom recovery via fastboot and do three wipes..
and did u just flashed the oem nd logo or the complete rom? if not, try flashing the complete ROM with replaced files
Faiyaz5yaz said:
check if recovery is working or flash a custom recovery via fastboot and do three wipes..
and did u just flashed the oem nd logo or the complete rom? if not, try flashing the complete ROM with replaced files
Click to expand...
Click to collapse
I am using cwm 6.0.5.1
This is all happening.
see screenshots
i replaced boot logo and oem in a complete stock rom and then flashed.
what to do now ??
Rishabh-The Developer said:
I am using cwm 6.0.5.1
This is all happening.
see screenshots
i replaced boot logo and oem in a complete stock rom and then flashed.
what to do now ??
Click to expand...
Click to collapse
after flashing rom ur oem gets locked.. if u have already unlocked, now root the mob again...
if that isn't the prob, as i already said, verify your file in memory card if it s properly downloaded nd copied
Faiyaz5yaz said:
after flashing rom ur oem gets locked.. if u have already unlocked, now root the mob again...
if that isn't the prob, as i already said, verify your file in memory card if it s properly downloaded nd copied
Click to expand...
Click to collapse
its properly downloaded and copied but it is not flashable.
you simply tell me that which stock rom can i use to make my phone working.
link please?
Rishabh-The Developer said:
its properly downloaded and copied but it is not flashable.
you simply tell me that which stock rom can i use to make my phone working.
link please?
Click to expand...
Click to collapse
well the cwm currently does not support flashing zip from sd card.. try adb side load if u hav unlocked bootloader and rooted..
if u don't want to do adb sideload, try flashing philz cwm.. its working perfectly..
Faiyaz5yaz said:
well the cwm currently does not support flashing zip from sd card.. try adb side load if u hav unlocked bootloader and rooted..
if u don't want to do adb sideload, try flashing philz cwm.. its working perfectly..
Click to expand...
Click to collapse
ok wo bhi krke dekhta hu....
Faiyaz5yaz said:
well the cwm currently does not support flashing zip from sd card.. try adb side load if u hav unlocked bootloader and rooted..
if u don't want to do adb sideload, try flashing philz cwm.. its working perfectly..
Click to expand...
Click to collapse
bro.
here is my whatsapp number - 8010159864
text me on it and then i send you some screenshots of my issue.
waiting for your message.
Rishabh-The Developer said:
ok wo bhi krke dekhta hu....
Click to expand...
Click to collapse
philz
http://forum.xda-developers.com/cro...e-general/sprout-philz-touch-v6-57-9-t2887574
Faiyaz5yaz said:
philz
http://forum.xda-developers.com/cro...e-general/sprout-philz-touch-v6-57-9-t2887574
Click to expand...
Click to collapse
already downloaded this file bro.
my micromax canvas a1 stuck on boot
Rishabh-The Developer said:
already downloaded this file bro.
Click to expand...
Click to collapse
Hi rishabh
Have u find the solution for your phone
Even I had faced the same issue
I had installed cwm recovery on my canvas a1
And tried to reboot. My. Phone got stucked on boot
Animation I can boot into cwm recovery mode,fasboot mode but unable to start
Device
Can u please help me
I even tried by erasing cache data and dalvik cache also
But of no use
Regards
Harish k
use sp flash tool
use sp flash tool for flashing stock rom
Hi,After flashing MIUI v6 rom from this link http://forum.xda-developers.com/redmi-1s/general/official-leaked-miui-6-beta-roms-t3070428
I lost Philz recovery.I cannot install it back through stack mi recovery.Please somebody help me....
miananth said:
Hi,After flashing MIUI v6 rom from this link http://forum.xda-developers.com/redmi-1s/general/official-leaked-miui-6-beta-roms-t3070428
I lost Philz recovery.I cannot install it back through stack mi recovery.Please somebody help me....
Click to expand...
Click to collapse
You can install custom recovery through your stock rom,just rename your recovery to update.zip and place it in root of internal storage or external.now go to updater app and select update.
chauhansonu104 said:
You can install custom recovery through your stock rom,just rename your recovery to update.zip and place it in root of internal storage or external.now go to updater app and select update.
Click to expand...
Click to collapse
I did the same but while flashing the recovery.It shows error....I even tried to flash via fastboot mode but my phone is not showing in fastboot menu.I'm using ubuntu 14.04
miananth said:
I did the same but while flashing the recovery.It shows error....I even tried to flash via fastboot mode but my phone is not showing in fastboot menu.I'm using ubuntu 14.04
Click to expand...
Click to collapse
If you cant do anything,then just try to flash Stock MIUI fastboot rom,after that flash any recovery(TWRP seems to be best).
miananth said:
Hi,After flashing MIUI v6 rom from this link http://forum.xda-developers.com/redmi-1s/general/official-leaked-miui-6-beta-roms-t3070428
I lost Philz recovery.I cannot install it back through stack mi recovery.Please somebody help me....
Click to expand...
Click to collapse
It seems you havent lost the rom, if sojust install flashify from playstore and install twrp.img file on flashify or twrp manager it also do the same.
miananth said:
I did the same but while flashing the recovery.It shows error....I even tried to flash via fastboot mode but my phone is not showing in fastboot menu.I'm using ubuntu 14.04
Click to expand...
Click to collapse
I think twrp officially supports Redmi 1s so go ahead and install Twrp manager from Google play and flash the latest build for your device. It will surely work...
gpreetham said:
I think twrp officially supports Redmi 1s so go ahead and install Twrp manager from Google play and flash the latest build for your device. It will surely work...
Click to expand...
Click to collapse
I flashed TWRP through TWRP manager app thanks for the tip...And thanks everyone for your help
miananth said:
I flashed TWRP through TWRP manager app thanks for the tip...And thanks everyone for your help
Click to expand...
Click to collapse
I'm happy to hear that...
Hello.I want to instal on my note 2 CM13.For now i'm ussing Dino note 4 rom and twrp recovery.
But when im starting recovery there are errors
Updating partition details...
....done
Full SELinuxx support is present.
Runnning boot script...
E:/sbin/runatboot.sh process ended with ERROR=1
Finished running boot script.
E:TWFunc::Copy_Log -- Cant open destiantion log file:
"/cache/recovery.log"
E:Unable to open "Cache/recovery/.version".
MTP Enabled
I cant install any rom and do anything on recovery Wipe or something.
Please help
Sorry for my english
kamilkular said:
Hello.I want to instal on my note 2 CM13.For now i'm ussing Dino note 4 rom and twrp recovery.
But when im starting recovery there are errors
Updating partition details...
....done
Full SELinuxx support is present.
Runnning boot script...
E:/sbin/runatboot.sh process ended with ERROR=1
Finished running boot script.
E:TWFunc::Copy_Log -- Cant open destiantion log file:
"/cache/recovery.log"
E:Unable to open "Cache/recovery/.version".
MTP Enabled
I cant install any rom and do anything on recovery Wipe or something.
Please help
Sorry for my english
Click to expand...
Click to collapse
Try to flash twrp via odin again and check whether it get rectified or not!
Sent from my SM-N910C
harsh09046 said:
Try to flash twrp via odin again and check whether it get rectified or not!
Sent from my SM-N910C
Click to expand...
Click to collapse
I flashed twrp with odin but doesnt work
kamilkular said:
I flashed twrp with odin but doesnt work
Click to expand...
Click to collapse
Now as i know or according to my knowledge,flash stock rom again via odin,then again root it with twrp(latest version 3.0.0) and flash custom rom of your choice
Sent from my SM-N910C
harsh09046 said:
Now as i know or according to my knowledge,flash stock rom again via odin,then again root it with twrp(latest version 3.0.0) and flash custom rom of your choice
Sent from my SM-N910C
Click to expand...
Click to collapse
You Had right.After install stock rom still nothing but when i changed recovery from TWRP to CWM it's work.Thanks for help !
kamilkular said:
You Had right.After install stock rom still nothing but when i changed recovery from TWRP to CWM it's work.Thanks for help !
Click to expand...
Click to collapse
Be happy [emoji106] [emoji1]
Sent from my SM-N910C
hi, i kinda have same problem like this now i'm using cm12 ROM i want to install rom like DN4 but on installing process sometime i getting error or stuck in installation progress i waiting in 2-4 hour but still don't have progress.