Related
Hi guys, first post for me here, im having major problems with my desire.
I was opening a zip file on my phone to change the font on it, and followed the instructions for a restart, upon restarting the phone the usual pink circle appeared in the centre of the screen (presumably because im on t-mobile), eventually this circle goes off, as it normally does, and i was expecting the t-mobile logo to appear as per usual, however the phone just restarted and the pink circle appeared again and kept doing this until i took the battery out the back to turn it off, when i turned the phone on again it just did the same thing.
I tried removing the sd card and the sim card but still made no difference. Im a bit of a noob at this type of thing so any help you can give me would be greatly appreciated.
Im a UK resident on t-mobile, im using a rooted phone.
I also tried a factory reset but this didnt work either, any help you can give would be a major help as i really miss my phone
Hi, try to do a full wipe trough recovery (hold vol down and power on), follow the onscreen instructions. If it doesn't work, try flashing the stock rom - t-mobile - http://shipped-roms.com/shipped/Bra...00.28U_4.06.00.02_2_release_127570_signed.exe
post if you come across problems
sorry as mentioned before, i am a noob, what do u mean by flashing?
ooops, sorry and welcome to xda
first download the rom in the link, it is an official t-mo rom, then connect your phone with the PC, make sure usb debugging is on (settings\applications\development you should have a green thick). Then start the exe and follow the onscreen instructions. Unfortunately you might need a goldcard which is a bit more complicated , that is if you get an error.
are you sure your phone is rooted? If that's the case power down, then power on while holding vol down, then navigate to "recovery" by pressing volume down, when you enter recovery look for "wipe device" "factory reset" or "full wipe", do it and see if you are alright then
try the second method first, with the recovery
hi thanks for the reply, i tried doing the full wipe on the phone unfortunately that didnt work. When trying to run the rom it says it cannot connect to the phone and i cant get into the phone to turn on debugging as it wont load up. this to me seems like it might be terminal unless you experts have any other advice.
Sometimes, when flashing an update ZIP, the framework might be wrong for your ROM and cause it to go into a bootloop (which it appears yours is doing).
Flashing the stock ROM is probably the best way, just need to get the correct RUU for your phone, make sure HTC Sync is connected and then run the file. If you can't turn the phone on the get HTC Sync to connect, turn off the phone and turn it back on whilst holding the back button to get into FASTBOOT. Connect to your PC again and then once it says FASTBOOT USB try again and it should work
It worked!! Thank you so much for helping me out guys, i really appreciate it!!
Hey guys, I'm normally silent in these forums 'cause I've never had a brick, just by reading correctly. This problem I'm having isn't a flashing brick! What happened is the following:
I know that the DHD in combi with my BT car radio is somewhat difficult (because of bad HTC coding). It seems that when I have my facebook friends in my contacts that the DHD starts slowing down and eventually hang when connected to the radio, because my radio tries to get every contact including it's info. Normally I do not sync my FB contacts with my DHD however I must have mistakingly done this.
Today I connected to my car radio and after getting out of the car my DHD showed that it was still connected (a sign that my DHD had the hang problem again). I turned of BT (took a hell of a time) and contiued on. When I came back I tried connecting the DHD again, however when I pushed the BT checkmark in settings it showed BT on, but no BT connection came up. So I went into BT settings only to find that BT wasn't turned on, then in the BT settings I checked turn BT on.
At that moment my DHD hang instantly, no inputs were registered at all. I waited a few minutes but nothing changed (I could still see the screen frozen at turning on BT). So I took out the battery and reinserted it, but when a pushed the power, the phone vibrated thrice and then did not boot, but only showed a flashing amber led.
I have rooted, S-offed and did the whole shebang to flash my DHD once. This was a long time ago and I haven't had any problems, all was OK. So at first I tried to search the forums, what might have happened. No post seems to be the same as my problem, because everyone is having these problems after an incorrect flash (my flash was correct, cause I've been using the ROM for more than 4 months!). Still I tried the solutions given in these posts (enter fastboot and flash again).
But it seems my DHD won't go into fastboot. When I hold VOLdown&power my DHD vibrates 5 times and shows a steady green led. So I thought maybe flashing a new ROM resolves the problem. If I cycle the battery and then connect is to my computer, my DHD goes into Clockwork recovery. From there I flased a new ROM to my DHD (update.zip method), but to no avail. I've factoryresetted, cleared al data, wiped battery stats, all to no avail...
As of this moment I'm at the end of my knowledge, I've done everything I know could have helped, but nothing did. Therefore I'm asking you, the Oracle of XDA (users), please does anyone have any clue what happened to my DHD and if so, how do I resolve the problem!
Thanks in advance for every little motivation/obligation you show be giving me your insights!
Info:
ROM: Android Revolution HD 2.0.9
CWM Recovery: 2.5.1.3
I've allready wiped battery stats as per this topic!
Additional thoughts: Might a hardware fault be the reason? Because it happened after some problems with BT, and also because I'm still able to correctly flash new ROMS with CWM though the problem remains?
Allright, so nobody know an answer I'm guessing... I've started the replacement process with my insurance company. However I'd still would like it if someone would know what the heck I did wrong...
Have you tried flashing a new radio, as that is what controls the hardware?
All a new ROM will do is update the RIL, not the radio.
http://forum.xda-developers.com/showthread.php?t=896597
Sent from my Desire HD using Tapatalk
It does more than likely seem like a hardware fault so it cant really be solved with software changes. Although I still would have tried to flash an RUU which updates basically everything on the phone to bare stock.
Use an RUU via your pc (v2.36 or lower so you can root it again) to restore to an out of the box state.
Allright guys, thanks for your ideas! I'm however experiencing problems trying your idea's. fFashing a radio or flashing a stock rom are not possible, because I need a connection with my computer. This connection is not possible, if I start the phone normally (or with vol down) I get the amber flashing light or the green steady light. Both do not connect to my pc, I get some device "Qualcomm CDMA Technologies MSN" for which windows can't find any drivers. When I let the DHD go into QWM recovery, the RUU won't find the DHD.
So I've tried extracting the RUU rom en putting this on the SDCARD of the DHD, but when I try to install it via CWM Recovery it says that it's an invalid file...
I actually bricked mine on purpose, and the thing that happened when it got bricked was that no lights and no life at all we're visible on the phone...
Atleast you get shakes and lights, thats a good sign!
Sadly i don't know what has to be done to restore it, but maybe Jkoljo does, PM him about your problem, if you get an assistance and some solving, write back here for your solution for others to use in the future!
They hang out in the Android Revolution HD IRC Channel, thats where i would go tbh.. Live support ftw!
Edit: While reading your above statement, it seems your drivers may be faulty in windows, redownload HTC Sync from htc.com, install, reboot, and try again.
The "Qualcomm CDMA ..." notification on the PC is a sign for the Qualcomm service mode. Also the 3 vibrates and the orange light is an indicator for that. You can enter this mode by pressing vol+ and power your device.
Stupid question, but is it possible that your vol+ button is stuck or something like that?
And you said you're able to enter CWM? how? I'm asking because you said you can't enter the bootloader.
I'll do some research when i get home today.
Meanwhile Try if ADB/Fastboot sees your phone
Edit: just checked my theory of the broken vol+ button: i held down my vol + button, took my battery out, reinserted it and powered up my phone. Result: 3 vibrates and a flashing orange light.
Then i did the same, but held down vol - ( vol+ still pressed). Result: your second phenomenon: a few vibrates and the green light stays on.
So I think this proves my theory because this is exactly what you described
I suggest you to play a bit with the vol+ button. Maybe the button will work again then
Sent from my Desire HD using Tapatalk
Well, I'm gonna fire up IRC then and try get some help. It's indeed not bricked as far as I'm guessing cause I do indeed have lights and I'm able to boot into CWM!
Flussen said:
The "Qualcomm CDMA ..." notification on the PC is a sign for the Qualcomm service mode. Also the 3 vibrates and the orange light is an indicator for that. You can enter this mode by pressing vol+ and power your device.
Stupid question, but is it possible that your vol+ button is stuck or something like that?
And you said you're able to enter CWM? how? I'm asking because you said you can't enter the bootloader.
I'll do some research when i get home today.
Meanwhile Try if ADB/Fastboot sees your phone
Sent from my Desire HD using Tapatalk
Click to expand...
Click to collapse
Right I'm guessing this is my problem! Just two days prior to resetting I started having problems with my VOL+ button (wouldn't work, only VOL- worked). So I'm guessing my hardware VOL+ button is broken and stuck to pressed...?
To answer your question about CWM: When I take out the battery so the phone is powered down, then reinsert the battery, connect the phone to the adapter or my computer (without pressing the power button), the phone boots into CWM after about 1 minute!
So after consolidating all the answers I'm guessing this is my problem: Hardware VOL+ is constantly pressed, therefore the phone boots consequently into Qualcomm service mode. Everything seems to be OK (flashing able to CWM), though just this little VOL+ problem puts my phone into an unusable brick...
The problem is that I'm not able to repair this myself (when I would try this, I'm guessing I'll break the seals therefore my insurance won't pay)... Anyone an idea how to circumvent the VOL+ button problem, without opening up my phone?
bdacier said:
Well, I'm gonna fire up IRC then and try get some help. It's indeed not bricked as far as I'm guessing cause I do indeed have lights and I'm able to boot into CWM!
Right I'm guessing this is my problem! Just two days prior to resetting I started having problems with my VOL+ button (wouldn't work, only VOL- worked). So I'm guessing my hardware VOL+ button is broken and stuck to pressed...?
To answer your question about CWM: When I take out the battery so the phone is powered down, then reinsert the battery, connect the phone to the adapter or my computer (without pressing the power button), the phone boots into CWM after about 1 minute!
So after consolidating all the answers I'm guessing this is my problem: Hardware VOL+ is constantly pressed, therefore the phone boots consequently into Qualcomm service mode. Everything seems to be OK (flashing able to CWM), though just this little VOL+ problem puts my phone into an unusable brick...
The problem is that I'm not able to repair this myself (when I would try this, I'm guessing I'll break the seals therefore my insurance won't pay)... Anyone an idea how to circumvent the VOL+ button problem, without opening up my phone?
Click to expand...
Click to collapse
Do you have needles at home? The ones you use when you repair cloth.. Try using one very carefully behind the volume +, you could also take a bit of A4 Paper, cut out some of it and make it fit between the gap of the Volume button, and try getting dirt out of there.
Allright, I've tried cleaning the VOL+ key but it still won't work. As a matter of fact I can feel a little "click" when pressing the VOL+ key, so I'm guessing the mechanical part of the key is working correctly. However when in CWM I can only use the VOL- key to switch thru the options, VOL+ is not registered by the phone. Therefore my assumption is that the there's a problem on the PCB with the VOL+ key, ergo a hardware fault... Insurance has been called and I'm up for a switch, now let's hope the insurance doesn't figure out I've rooted and installed another ROM than stock!
At least I wan't to thank all of you who've tried to help me! My ego has been saved, knowing it's indeed a hardware fault .
Cant you use adb within cwm to adb reboot bootloader?
Sent from my Desire HD using Tapatalk
bdacier said:
Allright, I've tried cleaning the VOL+ key but it still won't work. As a matter of fact I can feel a little "click" when pressing the VOL+ key, so I'm guessing the mechanical part of the key is working correctly. However when in CWM I can only use the VOL- key to switch thru the options, VOL+ is not registered by the phone. Therefore my assumption is that the there's a problem on the PCB with the VOL+ key, ergo a hardware fault... Insurance has been called and I'm up for a switch, now let's hope the insurance doesn't figure out I've rooted and installed another ROM than stock!
At least I wan't to thank all of you who've tried to help me! My ego has been saved, knowing it's indeed a hardware fault .
Click to expand...
Click to collapse
I've got the exact same problem! I don't have insurance on it though. And, im a day late for warranty.
What am i supposed to do? Any suggestions? Will htc deny my request to fix it coz it had a custom firmware?
Any help of any sort is appreciated.
I had exactly the same problem, and I'm sorry to say that I had to have it repaired. My button would also "click", but not register.
Maybe if you are buy a new power button from eBay?
Realising this is an old thread, but still:
I was just experiencing the same problem after I did a reboot to let one of my friends borrow my DHD to turn off the PIN code check on his SIM.
It started with the blinking lights (black screen), then I pulled the battery and found that my DHD was only accessible through ADB in recovery mode.
Did a couple of "ADB reboot" without any success, then tried using "ADB reboot recovery", which seemed to work (still black screen though), and then I did a "ADB reboot".
Back to normal!
hi , i had this issue too , its bcz of the moisture ur cell phone has absorb and as HTC desire HD very sensitive with its volume rocker area , the first thing that will be affected with moisture is ur volumer rocker circuit , try making it dry with a hair dryer blower or place ur phone in a rice sack for a day .
i am sure it will work .
OK.
I will put in a detailed info about what happened.
A week back, my wildfire's touchscreen started to function abnormally.
I was rooted and on Cyanogenmod 7.0.3
So, I flashed the phone with DK custom FROYO to make it look like sense so that the warranty is not void and took it to the HTC store.
They replaced the touchscreen for a flat fee (It was water damage according to them. But the phone was never used in wet conditions nor exposed to water)
But anyway, the phone was working fine when I brought it home from their store.
Then I flashed CM7.0.3 again.
And everything was working fine.
I OCed acc. to CM's settings to 652-352 Mhz.
And left the phone to charge in charger overnight.
When I woke up, the phone was off and there was just the red LED light blinking.
I tried to boot it again, but nothing works.
Pressing the power button does not do anything.
The phone still boots into recovery. At times.
I don't know what makes it boot into recovery. But at times it does, at times it doesn't. (Right now it's not booting into recovery no matter what I do)
Just the red LED keeps on blinking.
Please help.
I am not familiar with pushing commands onto the wildfire since I use a mac.
Please suggest any methods. If they involve using command line, I can use my windows PC for that. But please give a how-to of length enough for a noob ) ) to understand.
Thank you.
Pulz
EDIT :
I got to boot into recovery once. Tried to reflash CM7.0.3
It came to "Installing update" and then failed to go further.
Tried to install DK Custom Froyo 4.5
And it went to opening package and then failed to go further.
Now entering into a panic mode !
Red light blinking generally occurs when phone is hot and plugged in to wall socket. Is it so at that time ?
Unplug the charger or usb. Remove the battery and reinstall the battery. Try to boot into hboot mode (volume down + power) or fastboot mode (trackpad + power) . If your phone can boot into hboot/fastboot mode and has no restarts or power offs, then I think you can solve it.
Try to clear storage from hboot menu. Or factory reset from recovery once you enter it. If still it is not solved, try using "pc49img" method of flashing an RUU from the hboot menu. Hope it helps. Shouldn't help if there is hardware issue.
Sent from my Blade using XDA App
hye another noob here running on cm7.
actually i have the similiar problem my wildfire start rebooting over and over again but the cause is different.
this problem happen after i want to know what class my micro sd is.
what i do is i go to settings>storage>unmount sd card.
so after knowing the class were i insert back the card then the problem happens.
my phone start to crash then cm7 logo appear after that i enter my pin no so brought me back to the home screen after few seconds the logo appear again so i have 2 repeat the same steps...
this happen many times what i do is i remove the battery wait few hours then turn back on..
so help me if someone have the similiar problem and solutions.. thanks!!
Hello everyone. This is my first post here but I have been lingering around XDA particularly in Xperia S android development forum.
Today, I'm having a problem with my XS that it won't start up after i've done a few things related to installing new ROM in it. I'm not sure if it's bricked or anything but here's the full story and please tell me after reading:
My phone is as follows:
Xperia S
Unlocked Bootloader
Rooted
1) I was in my Recovery Mode (not TWRP as I was using a 4.1.2 JB ROM before) with a ROM installed.
2) Wiped Cache
3) Install ROM from SD Card
4) Successfully went through the ROM install wizard and installed it perfectly. I could've just used the ROM as usual but suddenly..
5) Then I went into Settings, I decided to do a Factory Reset (With wiping the internal storage too) <--- I thought doing this would only reset the current recently installed ROM and not wipe the ROM itself)
6) It reboots and bring me to the Recovery Mode page
7) I chose reboot my phone now option
8) It rebooted with the SONY logo on for a while
9) And then the triangle settings logo with a spanner and screwdriver logo show up. The screen stayed for a while like 20 seconds
10) And then it goes black..... and I can't get it start ever again (yet)
I don't know what on earth was I thinking doing a factory reset... that was dumb of me
That's how the story went... what should I do?
I've tried:
Holding the power button for 20 seconds(or longer), no vibrations, led or anything
Holding the vol up button for 20 seconds(or longer), no vibrations, led or anything
Holding both power+vol up button for 20 seconds(or longer), no vibrations, led or anything
Connecting the phone to laptop using USB to see if it is detected by my laptop but no nothing happened though (I did not press any button while connected)
Enter FLASHMODE using the proper way (using flashtool and everything) but fruitless
Charging so that the Red LED comes out when phone runs out battery and resetted. But so far still nothing (6 hours+ charging)
So at this point what has happened to my phone? Is this considered 'bricked'? Is it over for my phone now? Can I do anything to get it back running? Please help.
Thank you so much in advance for reading and helping me out.
Case: [UNSOLVED]
bump
DualElites said:
bump
Click to expand...
Click to collapse
anyone can help me out here? :crying:
DualElites said:
anyone can help me out here? :crying:
Click to expand...
Click to collapse
Have you tried to enter in FASTBOOT mode and flash a new recovery?
DualElites said:
Hello everyone. This is my first post here but I have been lingering around XDA particularly in Xperia S android development forum.
Today, I'm having a problem with my XS that it won't start up after i've done a few things related to installing new ROM in it. I'm not sure if it's bricked or anything but here's the full story and please tell me after reading:
My phone is as follows:
Xperia S
Unlocked Bootloader
Rooted
1) I was in my Recovery Mode (not TWRP as I was using a 4.1.2 JB ROM before) with a ROM installed.
2) Wiped Cache
3) Install ROM from SD Card
4) Successfully went through the ROM install wizard and installed it perfectly. I could've just used the ROM as usual but suddenly..
5) Then I went into Settings, I decided to do a Factory Reset (With wiping the internal storage too) <--- I thought doing this would only reset the current recently installed ROM and not wipe the ROM itself)
6) It reboots and bring me to the Recovery Mode page
7) I chose reboot my phone now option
8) It rebooted with the SONY logo on for a while
9) And then the triangle settings logo with a spanner and screwdriver logo show up. The screen stayed for a while like 20 seconds
10) And then it goes black..... and I can't get it start ever again (yet)
I don't know what on earth was I thinking doing a factory reset... that was dumb of me
That's how the story went... what should I do?
I've tried:
Holding the power button for 20 seconds(or longer), no vibrations, led or anything
Holding the vol up button for 20 seconds(or longer), no vibrations, led or anything
Holding both power+vol up button for 20 seconds(or longer), no vibrations, led or anything
Connecting the phone to laptop using USB to see if it is detected by my laptop but no nothing happened though (I did not press any button while connected)
Enter FLASHMODE using the proper way (using flashtool and everything) but fruitless
Charging so that the Red LED comes out when phone runs out battery and resetted. But so far still nothing (6 hours+ charging)
So at this point what has happened to my phone? Is this considered 'bricked'? Is it over for my phone now? Can I do anything to get it back running? Please help.
Thank you so much in advance for reading and helping me out.
Case: [UNSOLVED]
Click to expand...
Click to collapse
chill dude, dont panic, this was happened with me too a month ago, here what i did, i downlaod the .96 ftf file and flashed it in fastboot mode, in my situation, phone was on bootloop and your phone is turnning off so you can get into the fastboot easily,
have u tried sony update service? i broke my hp too... then i realised that i can actually use sony update service and press the volume down button and plug in my hp and update my fw to the original sony fw. hope this method helps for u.
Chill.
Alright dude, so chill. I recommend you to download Sony PC companion software and click on "Repair my device" from there. Then, you just have to follow the instructions and it should work. Tell me if it hasn't, I will help you
TheAkshay said:
Alright dude, so chill. I recommend you to download Sony PC companion software and click on "Repair my device" from there. Then, you just have to follow the instructions and it should work. Tell me if it hasn't, I will help you
Click to expand...
Click to collapse
Would this work with a unlocked bootloader and rooted SXS?? Having problems with my data partition because I think it's corrupted. But I can still use my phone if it doesn't shut down the normal way.
Xperia SLhard bricked afer wrong cwn recovery 6.0.4.4 insatlled
itsmarc19 said:
Would this work with a unlocked bootloader and rooted SXS?? Having problems with my data partition because I think it's corrupted. But I can still use my phone if it doesn't shut down the normal way.
Click to expand...
Click to collapse
I have the same issue with my Xperia SL.I wrongly install cwm recovery 6.0.4.4 by recover mode through option update.zip. Its done all the damage to my XSL. No Fastboot Mode, No Flash mode, No vibration nothing...Plz Help me guys...Plz
Yeah.
Yep. It should work.
I have htc One x, and i dont know which version it is, no details at all about anything regarding it. My brother got it from someone and screwed up in flashing.
Now its stuck on white HTC quietly brilliant screen, I have tried repeatedly to boot into fastboot or bootloader and nothing works.
It charges properly when its switched off with red led lighting up but after that nothing
I have searched innumerable threads but they all metnion to go into bootloader mode, but my phone doesnt even go there
Please anyone can help me out?
I can pay as well for the services
visheshsahlot said:
I have htc One x, and i dont know which version it is, no details at all about anything regarding it. My brother got it from someone and screwed up in flashing.
Now its stuck on white HTC quietly brilliant screen, I have tried repeatedly to boot into fastboot or bootloader and nothing works.
It charges properly when its switched off with red led lighting up but after that nothing
I have searched innumerable threads but they all metnion to go into bootloader mode, but my phone doesnt even go there
Please anyone can help me out?
I can pay as well for the services
Click to expand...
Click to collapse
No need to pay first try to hold the volume down button and then hold power button untill you go in bootloader after this connect the phone to a computer if your battery is empty the best way is to connect battery pack on the back side pins and try then go in bootloader but if your battery iss complete dead no solution you must to charge ytour phone but this can be done from bootloader with the bat file
EDIT: Next time when you are in trouble ask before discharge the phone
Have you flashed boot.img?
E: se this too
http://forum.xda-developers.com/showthread.php?p=26192390
Hi disaster Again
the above problem i mentioned was solved, i could get my laptop to recognise the phone in ADB and i just had to enter the command adb reboot bootloader.
but now i have even bigger problem. i was running ARHD and everything was going fine unless i decided to upgrade to miui based on 4.4.4
so i went into fastboot by typing adb reboot bootloader and then flashed the boot.img of miui rom, then i pressed power down in fastboot thinking i'll connect and then go into recovery and then flash the zip of the rom
but now i cant get into either recovery or fastboot(bootloader) and neither my phone is recognised in adb.
please guys help me out.
Have you read this and followed all steps exactly?
Can you enter bootloader holding vol down and power button?
Do you have recovery on device?
See i cannot go into bootloader or recovery anyhow, yes i had recovery on my device by which i flashed the ARHD
i Flashed the boot image for the MIUI bases on 4.4.4 but now it doesnt boot up, neither i can nacces bootloader nor it is recognised by ADB
c.e.z said:
Have you read this and followed all steps exactly?
Can you enter bootloader holding vol down and power button?
Do you have recovery on device?
Click to expand...
Click to collapse
Please anyone, please help me out
I think I have totally killed my phone, my parents wont give me a new one in any case.
so anyone please by my saviour
I have a backup of my ARHD rom through CWM internal storage as well, just wanted to inform so that you can all help me just save this device
visheshsahlot said:
I have a backup of my ARHD rom through CWM internal storage as well, just wanted to inform so that you can all help me just save this device
Click to expand...
Click to collapse
if you can't go in bootloader or recovery nobody can't help you. Try on diferent computer with win7 32bit