Hi
I've flashed my phone for the first time yesterday so im totally new too all this. I tried to install cyanogen mod and I think i might have forgotten to do a wipe data/factory reset, but I'm not sure. Afterwards my phone is stuck on the cyanogen boot screen and I can't access recovery either. I can access download mode so i tried to flash a stock ROM with Odin but it gave me this error message:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9195XXUBML4_I9195NEEBNB1_I9195XXUBML4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
any suggestions anyone? I really miss my new phone.
Try to flash a newer firmware
Related
So I was attempting to flash the CWM6 safe kernel to upgrade to CM9 beta 1 on my girlfriend's phone. The kernel flash didn't go well and the phone was stuck at the splash screen. I'm attempting to ODIN FH13 via One Click. ODIN sees the phone, and the process starts...but always fails at:
<ID:0/012> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/012> Odin v.3 engine (ID:12)..
<ID:0/012> File analysis..
<ID:0/012> SetupConnection..
<ID:0/012>
<OSM> All threads completed. (succeed 0 / failed 1)
Any ideas/help?
Thanks in advance.
Nevermind...it all the of the sudden felt like working after 3 attempts.
Ok, I got a new Note II the other day with 4.3 already installed via Kies or OTA. I attempted to push, via ODIN, "CF-Auto-Root-d2tmo-d2tmo-sght999.tar". I REALIZE THIS IS THE ROOT FOR S3; I KNOW I FLASHED THE WRONG FILE. PLEASE DO NOT POST SAYING I FLASHED THE WRONG FILE. I KNOW I SCREWED UP BIG TIME, AND I'M HOPING SOMEONE IS NICE ENOUGH TO TRY AND HELP ME THROUGH THIS. My laptop sat there for the better part of 2 hours acting like ODIN was cranking along but the bar never moved. After 2 hours, I had to pull the cord from the phone (stupid move, I know!), and this is, of course, where the problem began.
Now, I get the coveted "Firmware Upgrade encountered an issue. Please select recovery mode in Kies & try again." screen. The phone will, obviously, go no further than this in booting up. I am able to get to download mode.
I attempted to install JellyBean Release 4.3 (December 2013) from this thread to alleviate the issue. Here's the ODIN result:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> root66_TMO_T889UVUCMK7_2.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> boot.img
<ID:0/004> NAND Write Start!!
<ID:0/004> cache.img
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Removed!!
Now, as I sit here and write this, I think installing a stock firmware like this one might not work at all. I need to install a recovery (stock or otherwise) to make this problem disappear. I tried to reinstall the CF-Auto-Root file and got this result:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CF-Auto-Root-d2tmo-d2tmo-sght999.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> All threads completed. (succeed 0 / failed 0)
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CF-Auto-Root-d2tmo-d2tmo-sght999.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Removed!!
Again, it didn't do anything for hours. I pulled the cord again since it didn't look like it was actually writing anything to my phone.
I don't think I can use KIES as a last resort since I never backed up the phone through KIES before. I am out of ideas, and I would really like to get this phone operational again. Also, the serial number has been removed from the device (Igot the phone from Ebay), so I don't think I could use this route either.
Any and all help would be greatly appreciated.
Thanks in advance!
Download and flash CF auto-root for sgh-t889(link below)it includes recovery, then perform factory reset by rebooting in to recovery.
http://download.chainfire.eu/266/CF-Root/CF-Auto-Root/CF-Auto-Root-t0ltetmo-t0ltetmo-sght889.zip
Sent from my SGH-T889 using xda app-developers app
My phone just boots to the "Saumsung Galaxy Note II" screen and it is stuck there. I dont think its a loop because it doesnt loop (by that I mean it doesnt disappear and appear).
I m afraid using odin would erase everything.
I want to save my data, what should I do? Which rom do i use?
I tried downloading 3 to 4 note 2 roms but they all failed in odin.
Please specify what I need to download in order to save my data.
At this point, I am also ready to just give up and restore factory settings. I went to the at&t technicans, who are completely useless and they used their roms and couldnt help at all. I went to a fix phone place and they couldnt do anything either.
Please help!
Your request is ambiguous at best.
.
We have absolutely no idea what you have done beyond flashing multiple roms to the device..
I assume the device is dirty due too multiple frameworks being flashed over one another..
If it were my device...I'd go clean slate and restore the device to a stock configuration and work up from there.
.
It's a mess in there for sure.
So see the return to stock thread in the general section...and use Odin if possible....and IMHO...stay away from kies....g
i have no idea either. for all i know, none of them did anything since they all failed after this boot freeze has been happening.
im trying to go clean slate but i cant even do that.
im trying to odin with http://www.sammobile.com/firmwares/confirm/13212/I317UCAMA4_I317ATTAMA4_ATT/
but it doesnt work either!!!
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> KIES_HOME_I317UCAMA4_I317ATTAMA4_578342_REV04_user _low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
downloaded both roms and both failed again
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> KIES_HOME_I317UCALJ2_I317ATTALJ2_215287_REV04_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I have a Galaxy S3 Tmobile - not rooted. I wiped my phone to default and when it tried to power on, it gave me couldn't mount e:\ - don't remember the exact path. After attempting to flash with stock firmware T999UVDMD5_T999TMBDMD5_TMB and 16GB.pit file with odin 3.04 and 3.07 that failed:
Odin:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> T999UVDMD5_T999TMBDMD5_T999UVDMD5_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Complete(Write) operation failed.
<ID:0/005> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Phone:
ODIN MODE
Product Name: SGH-T999L
CUSTOM BINARY DOWNLOAD: Yes (1 counts)
CURRENT BINARY: Custom
SYSTEM STATUS: Official
QUALCOMM SECUREBOOT: ENABLE
Warranty Bit; 0
BOOTLOADER Bit: 0
SECURE CHECK FAIL: PIT
Thanks in advance!
Try flashing without the PIT file?
audit13 said:
Try flashing without the PIT file?
Click to expand...
Click to collapse
I've tried that but it still fails:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> T999UVUENC2_T999TMBENC2_T999UVUENC2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Which bootloader is on the phone? Are the error messages from Odin 3.07? Are you unchecking everything except f.reset time and auto reboot in Odin?
Using Unofficial LineageOS 14.1 (v2awifi). During using my Tab Pro 12.2 SM-T900 I got a failure and switched off my tablet. Since that time I can't start my tablet. Can only turn on my tablet in downloadmode. Can't enter recovery. Tried to flash TWRP, but that is not possible. Because the failure was suddenly, I could not and can't switch and change usb-debugging and media-transfer possiblities.
I tried to install Stock Rom with Odin, got the next faillures:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1203)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003>
<ID:0/003> There is no PIT partition.
<OSM> All threads completed. (succeed 0 / failed 1)
And sometimes:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1203)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Can't open the serial(COM) port.
<OSM> All threads completed. (succeed 0 / failed 1)
So I can't flash the stock rom for repairing my ROM. Please help me, so that I can use my tablet again. How to fix PIT-partion ?
I have the same problem. Any resolution?
Same but on an SM-T320. Flashed an appropriate PIT, stock firmware...nothing working. I'm thinking it's a physical issue at this point.