Ok, I got a new Note II the other day with 4.3 already installed via Kies or OTA. I attempted to push, via ODIN, "CF-Auto-Root-d2tmo-d2tmo-sght999.tar". I REALIZE THIS IS THE ROOT FOR S3; I KNOW I FLASHED THE WRONG FILE. PLEASE DO NOT POST SAYING I FLASHED THE WRONG FILE. I KNOW I SCREWED UP BIG TIME, AND I'M HOPING SOMEONE IS NICE ENOUGH TO TRY AND HELP ME THROUGH THIS. My laptop sat there for the better part of 2 hours acting like ODIN was cranking along but the bar never moved. After 2 hours, I had to pull the cord from the phone (stupid move, I know!), and this is, of course, where the problem began.
Now, I get the coveted "Firmware Upgrade encountered an issue. Please select recovery mode in Kies & try again." screen. The phone will, obviously, go no further than this in booting up. I am able to get to download mode.
I attempted to install JellyBean Release 4.3 (December 2013) from this thread to alleviate the issue. Here's the ODIN result:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> root66_TMO_T889UVUCMK7_2.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> boot.img
<ID:0/004> NAND Write Start!!
<ID:0/004> cache.img
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Removed!!
Now, as I sit here and write this, I think installing a stock firmware like this one might not work at all. I need to install a recovery (stock or otherwise) to make this problem disappear. I tried to reinstall the CF-Auto-Root file and got this result:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CF-Auto-Root-d2tmo-d2tmo-sght999.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> All threads completed. (succeed 0 / failed 0)
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CF-Auto-Root-d2tmo-d2tmo-sght999.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Removed!!
Again, it didn't do anything for hours. I pulled the cord again since it didn't look like it was actually writing anything to my phone.
I don't think I can use KIES as a last resort since I never backed up the phone through KIES before. I am out of ideas, and I would really like to get this phone operational again. Also, the serial number has been removed from the device (Igot the phone from Ebay), so I don't think I could use this route either.
Any and all help would be greatly appreciated.
Thanks in advance!
Download and flash CF auto-root for sgh-t889(link below)it includes recovery, then perform factory reset by rebooting in to recovery.
http://download.chainfire.eu/266/CF-Root/CF-Auto-Root/CF-Auto-Root-t0ltetmo-t0ltetmo-sght889.zip
Sent from my SGH-T889 using xda app-developers app
Hi
I've flashed my phone for the first time yesterday so im totally new too all this. I tried to install cyanogen mod and I think i might have forgotten to do a wipe data/factory reset, but I'm not sure. Afterwards my phone is stuck on the cyanogen boot screen and I can't access recovery either. I can access download mode so i tried to flash a stock ROM with Odin but it gave me this error message:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9195XXUBML4_I9195NEEBNB1_I9195XXUBML4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
any suggestions anyone? I really miss my new phone.
Try to flash a newer firmware
My phone just boots to the "Saumsung Galaxy Note II" screen and it is stuck there. I dont think its a loop because it doesnt loop (by that I mean it doesnt disappear and appear).
I m afraid using odin would erase everything.
I want to save my data, what should I do? Which rom do i use?
I tried downloading 3 to 4 note 2 roms but they all failed in odin.
Please specify what I need to download in order to save my data.
At this point, I am also ready to just give up and restore factory settings. I went to the at&t technicans, who are completely useless and they used their roms and couldnt help at all. I went to a fix phone place and they couldnt do anything either.
Please help!
Your request is ambiguous at best.
.
We have absolutely no idea what you have done beyond flashing multiple roms to the device..
I assume the device is dirty due too multiple frameworks being flashed over one another..
If it were my device...I'd go clean slate and restore the device to a stock configuration and work up from there.
.
It's a mess in there for sure.
So see the return to stock thread in the general section...and use Odin if possible....and IMHO...stay away from kies....g
i have no idea either. for all i know, none of them did anything since they all failed after this boot freeze has been happening.
im trying to go clean slate but i cant even do that.
im trying to odin with http://www.sammobile.com/firmwares/confirm/13212/I317UCAMA4_I317ATTAMA4_ATT/
but it doesnt work either!!!
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> KIES_HOME_I317UCAMA4_I317ATTAMA4_578342_REV04_user _low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
downloaded both roms and both failed again
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> KIES_HOME_I317UCALJ2_I317ATTALJ2_215287_REV04_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I have a Galaxy S3 Tmobile - not rooted. I wiped my phone to default and when it tried to power on, it gave me couldn't mount e:\ - don't remember the exact path. After attempting to flash with stock firmware T999UVDMD5_T999TMBDMD5_TMB and 16GB.pit file with odin 3.04 and 3.07 that failed:
Odin:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> T999UVDMD5_T999TMBDMD5_T999UVDMD5_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Complete(Write) operation failed.
<ID:0/005> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Phone:
ODIN MODE
Product Name: SGH-T999L
CUSTOM BINARY DOWNLOAD: Yes (1 counts)
CURRENT BINARY: Custom
SYSTEM STATUS: Official
QUALCOMM SECUREBOOT: ENABLE
Warranty Bit; 0
BOOTLOADER Bit: 0
SECURE CHECK FAIL: PIT
Thanks in advance!
Try flashing without the PIT file?
audit13 said:
Try flashing without the PIT file?
Click to expand...
Click to collapse
I've tried that but it still fails:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> T999UVUENC2_T999TMBENC2_T999UVUENC2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Which bootloader is on the phone? Are the error messages from Odin 3.07? Are you unchecking everything except f.reset time and auto reboot in Odin?
Alright so I'm trying to figure out what I'm doing wrong. I downloaded a copy of the pre-borked Note 7 firmware and I'm trying to flash it through ODIN. Every time I try, I get errors on both the phone and on the software.
I've been Googling all day and I can't find an explanation or a workaround. Can the experts here help with this?
ODIN log:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin engine v(ID:3.1203)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> emmc_appsboot.mbn
<ID:0/003> lksecapp.mbn
<ID:0/003> xbl.elf
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Note 7 display:
ODIN MODE (HIGH SPEED)
PRODUCT NAME: SM-N930A
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Official
FRP LOCK: ON
OID:
WARRANTY VOID: 0x0
QUALCOMM SECUREBOOT: ENABLE
AP SWREV: B2 (1,1,1,1,1) K2 S2
SECURE DOWNLOAD: ENABLE
CCIC:S2MM005 HW:3 Boot: 5 Main:ab
Then the actual error:
SW REV CHECK FAIL : [about]Fused 2 > Binary 1
[1]eMMC wrie fail: aboot
where did you find the firmware from ?
Having same issue
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin engine v(ID:3.1205)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Set PIT file..
<ID:0/006> DO NOT TURN OFF TARGET!!
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> SingleDownload.
<ID:0/006> emmc_appsboot.mbn
<ID:0/006> lksecapp.mbn
<ID:0/006> xbl.elf
<ID:0/006> FAIL! (Auth)
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I got the file from: https://www.androidfilehost.com/?fid=24651430732236681
ALL_SPT_N930PVPU1APH3_N930PSPT1APH3_CL8706608_QB10617237_REV00_userdebug_low_noship_MULTI_CERT.tar.md5
for the Samsung Galaxy Note 7(SM-N930T), by freeza
Good thing it failed, thats for T-Mobile, if it completed it would have bricked your phone. I am searching also for the AT&T version
I believe that the SM-N930P version is for Sprint. My carrier is Sprint
From my understanding, the firmware available online, which ends in PH1 has the old bootloader. Once the battery warning update hit (Green Battery Icon for those who have the replacement model) the firmware came with a new bootloader and firmware version ending in PHE.
Because of this, we cannot flash PH1 due to the bootloader change.
The 60% battery update (PK1), I BELIEVE, still uses the same bootloader as PHE.
The only solution I think would be as follows:
1) Immediately disable any future software updates. (We dont want another bootloader change)
2) Someone needs to find and or upload the PHE version firmware (which lets you charge 100%, and only has the annoying original message sometimes)
3) Backup everything.
4) Using the methods described in other places, flash the PHE version, charge to 100% and deal with only a few warning mesages. (Phone startup and Attach to charger)
4) Immediately disable any future software updates by following the instructions for Package Disabler PRO or EZ Disabler. (Making sure you're on airplane mode, SIM card out, and wifi is turned off)
These are my thoughts. I cant seem to find PHE firmware anywhere. One place has it supposedly, it seems shady cause the download link goes to an arabic website and the forums require you to pay for each download. (hmmmm.....)
I could be 100% wrong, Im not an expert by any means, just another user trying to join the community to help find a solution. Can anyone confirm Im wrong and they have been able to somehow flash the PH1 baseband firmware? Any and all help would greatly help me and the many others who have been held down by the man
SM-N930A Update
I have the N930AUCS1APH1_N930AATT1APH1_ATT_FULL_SAMFIRM.NET ROM with 4 .md5 files in it (BL, AP, CP, and CSP) and I can not get the phone to flash using Odin 3.12? Any ideas on what to do? This is my log, but basically just says failed!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin engine v(ID:3.1203)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Removed!!
next update will knock us all off the network. They are telling people that in the support calls to carriers and samsung.
Here is the PK1 firmware image
Hey guys, I am going to give you guys looking to get back to 100% charging a good new. I found the PK1 image for AT&T Note 7 N930A version. I just re-flashed my phone and it worked just fine. Got to charge my phone back to 100%. Got the green battery sign back. Here is the firmware image.
androidfilehost.com/?fid=312978532265363403 (I had to skip the www prefix because I am not allowed to post url at the moment. You guys know what to do with it. Just copy and paste.
Had to use Odin 3.12.3 version. I tried with Odin 3.10.7 version but got Odin protocol version error. So use Odin 3.12.3 version. Good luck.
---------- Post added at 09:58 AM ---------- Previous post was at 09:53 AM ----------
Sorry, my previous post should have said PKE firmware image.
---------- Post added at 10:03 AM ---------- Previous post was at 09:58 AM ----------
Got to check my spelling. PHE. Not PKE.
Thanks hachika88, that worked great. Does anyone know what I need to disable to prevent it from updating again. I have disabled com.samsung.knox.appsupdateagent and com.ws.dm, but is there anything else that should be disabled?
Use this link to go back to 100% on Rev 2 Firmware flash win Odin 3.12.4 or 3.12.3
androidfilehost.com/?fid=457084094631641284
Use Samsung Package Disabler Pro to disable Software Updates apk but you must do it fast after you reset your phone because once your phone checks for updates you can no longer disable it. Keep your SIM card out the phone and disconnect from wifi until absolutely necessary to get it disabled.
Good Luck
I used abd script to block th updates instead. A friend had her phe firmware pulled so that people could use it. If you look
http://www.n7r.co/
im looking for SM-N930A pl2 firmware. anyone?