Remove TWRP recovery version? - Huawei Ascend P6, Mate

How to remove TWRP v2.6.3.3 from my Huawei P6 U06
1) When I use fastboot to flash new_recovery, after reboot to recovery, the old_recovery still here again???
Configuration Android 4.4.2
Recovery Rooted
TWRP v2.6.3.3
MIUI ROM version which stop à MIUI logo
Error when try to wipe /cache is "E:Unable to moun /cache"

LikeM8 said:
How to remove TWRP v2.6.3.3 from my Huawei P6 U06
1) When I use fastboot to flash new_recovery, after reboot to recovery, the old_recovery still here again???
Configuration Android 4.4.2
Recovery Rooted
TWRP v2.6.3.3
MIUI ROM version which stop à MIUI logo
Error when try to wipe /cache is "E:Unable to moun /cache"
Click to expand...
Click to collapse
Any way to remove TWRP 2.6.3.3 version??? I try to use fix posted by surdu_petru and all failed, TWRP 2.6.3.3 version is still here??? Does some one succed to remove it and back to stock recovery?

yes many times..
connect your phone to the pc..
wait 'til your pc recognizes your phone..
enable debug mode under settings-developer options..
then load the adb cmd console..
then type "adb devices" (without "")..
if your phone is found you can do the next step..
type "adb reboot bootloader"..
then wait a few seconds..
before this you should have put the respective recovery.img from your firmware inside the adb folder (from where you started the adb cmd)..
when your phone seems to stuck on the huawei logo you can check if your phone is still recognized by the pc - type "fastboot devices" - it should show some weird things - thats ok..
then you can flash the stock recovery by typing "fastboot flash recovery recovery.img" (the .img must be exactly written how you have it inside the mentioned folder, e.g. b512_recovery.img)..
then you should see some lines describing what the adb has done (sending, writing,flashing or so)..
and that's it..
you should have a stock recovery..
you have just to reboot your phone now by typing "fastboot reboot"..

blueIBI said:
yes many times..
connect your phone to the pc..
wait 'til your pc recognizes your phone..
enable debug mode under settings-developer options..
then load the adb cmd console..
then type "adb devices" (without "")..
if your phone is found you can do the next step..
type "adb reboot bootloader"..
then wait a few seconds..
before this you should have put the respective recovery.img from your firmware inside the adb folder (from where you started the adb cmd)..
when your phone seems to stuck on the huawei logo you can check if your phone is still recognized by the pc - type "fastboot devices" - it should show some weird things - thats ok..
then you can flash the stock recovery by typing "fastboot flash recovery recovery.img" (the .img must be exactly written how you have it inside the mentioned folder, e.g. b512_recovery.img)..
then you should see some lines describing what the adb has done (sending, writing,flashing or so)..
and that's it..
you should have a stock recovery..
you have just to reboot your phone now by typing "fastboot reboot"..
Click to expand...
Click to collapse
Thnaks for your reply but I do this before and failed!
adb devices comand retourn ID phone but fastboot devices something very different ???
"fastboot oem getvar product" return U9510 ??? whats wrong?

hm..the getvar cmd is unknown to me..very strange..

LikeM8 said:
How to remove TWRP v2.6.3.3 from my Huawei P6 U06
1) When I use fastboot to flash new_recovery, after reboot to recovery, the old_recovery still here again???
Configuration Android 4.4.2
Recovery Rooted
TWRP v2.6.3.3
MIUI ROM version which stop à MIUI logo
Error when try to wipe /cache is "E:Unable to moun /cache"
Click to expand...
Click to collapse
Its look like you catch a wrong turn..
I recommend reflash your stock rom..
If only bootloader doesn't work..

AArga said:
Its look like you catch a wrong turn..
I recommend reflash your stock rom..
If only bootloader doesn't work..
Click to expand...
Click to collapse
What do you mean by wrong turn???
I can flash stock rom because:
1) I have TWRP 2.6.3.3 version and I can not back to stock
2) Error from TWRP is "E: Unable to mount '/Ecache"
3) I try to use dload folder with UPDATE.APP and its failed!
4) The phone boot and stop at MIUI logo

LikeM8 said:
What do you mean by wrong turn???
I can flash stock rom because:
1) I have TWRP 2.6.3.3 version and I can not back to stock
2) Error from TWRP is "E: Unable to mount '/Ecache"
3) I try to use dload folder with UPDATE.APP and its failed!
4) The phone boot and stop at MIUI logo
Click to expand...
Click to collapse
Calm man..
If you on stuck.. Cant bootup.. You must reflash your phone firmware..
Cant mount means your twrp has bugs.. Or your firmware corrupt.Try with another source.. To download..

AArga said:
Calm man..
If you on stuck.. Cant bootup.. You must reflash your phone firmware..
Cant mount means your twrp has bugs.. Or your firmware corrupt.Try with another source.. To download..
Click to expand...
Click to collapse
Thanks AArga to reply, I do not any fix???

LikeM8 said:
Thanks AArga to reply, I do not any fix???
Click to expand...
Click to collapse
If you want you can reflash your stock rom.. With pc.. If happened bootloop..

you have the wrong twrp version for miui..look here: http://forum.xda-developers.com/showthread.php?t=2534420

blueIBI said:
you have the wrong twrp version for miui..look here: http://forum.xda-developers.com/showthread.php?t=2534420
Click to expand...
Click to collapse
Ok and what I have to back to recovery stock version?

i dont know if thia is possible..but try to update your twrp to minimum 2.7.0.0 (or higher)

Related

[Q] huawei ascend p6 multiloader

I think i have bricked my p6 after flashing boot(b125).img from fastboot and its stuck and restarting at bootscreen. Pls someone help with heawei multiloader as am told it can fix bricked phone from usb. File now no more assessible from huawei website. pls help.
Hey do you have twrp recovery installed? Have you already tried to get into your stock recovery ?( Holding volume up/down button simultanesly during boot)
nourudeen said:
I think i have bricked my p6 after flashing boot(b125).img from fastboot and its stuck and restarting at bootscreen. Pls someone help with heawei multiloader as am told it can fix bricked phone from usb. File now no more assessible from huawei website. pls help.
Click to expand...
Click to collapse
WisdomSeeker said:
Hey do you have twrp recovery installed? Have you already tried to get into your stock recovery ?( Holding volume up/down button simultanesly during boot)
Click to expand...
Click to collapse
my phone never came with any stock recovery. had 'factory mode' not recovery when holding those bottons. In factory mode, no option for flashing anything. Now phone only restarts on bootscreen and then on-off. initially tried flashing TWRP just befor bricking phone but adb gave error like this 'partition not support flash and i had already flash a boot.img for b125
b608 version of my phone was a brick was b118 installed, there is a solution?
sorry my poor english, I'm from Turkey, please help, please..
Both of you should try to flash the stock recovery! You can download it here www).androidfilehost.(com)/?fid=23252070760973625 (just remove the brackets) .
Then follow these steps:
1. Put your device in fastboot mode ( > adb reboot bootloader )
2. Flash recovery via fastboot ( fastboot flash recovery recovery.img )
3. Reboot via fastboot ( fastboot reboot )
Afterwards try to reboot to your stock recovery . Then you can simply install over the update.app a fresh Huawei Firmware
Greetings Wisdomseeker
WisdomSeeker said:
Both of you should try to flash the stock recovery! You can download it here www).androidfilehost.(com)/?fid=23252070760973625 (just remove the brackets) .
Then follow these steps:
1. Put your device in fastboot mode ( > adb reboot bootloader )
2. Flash recovery via fastboot ( fastboot flash recovery recovery.img )
3. Reboot via fastboot ( fastboot reboot )
Afterwards try to reboot to your stock recovery . Then you can simply install over the update.app a fresh Huawei Firmware
Greetings Wisdomseeker
Click to expand...
Click to collapse
well wisdom, like i said, its restarting at boot screen so i cant get to fastboot. i sometimes able to enter an android (3e) recovery and try installing what u said but each time, installation is stopped. Got a certain miui rom and halfway it says NOT VALID OTA PACKAGE. SCATTER FILE MISSING. All other package rom or other recovery refuse to install and say ERROR. i have tried this your files but not possible.
nourudeen said:
well wisdom, like i said, its restarting at boot screen so i cant get to fastboot. i sometimes able to enter an android (3e) recovery and try installing what u said but each time, installation is stopped. Got a certain miui rom and halfway it says NOT VALID OTA PACKAGE. SCATTER FILE MISSING. All other package rom or other recovery refuse to install and say ERROR. i have tried this your files but not possible.
Click to expand...
Click to collapse
Maybe you should try To use another SD card Or mabye Format the current one and then add the update.APP To it
PHP:
WisdomSeeker said:
Maybe you should try To use another SD card Or mabye Format the current one and then add the update.APP To it
PHP:
Click to expand...
Click to collapse
No luck! I think the huawei multiloader will do the work. Any Idea where i can download?
nourudeen said:
No luck! I think the huawei multiloader will do the work. Any Idea where i can download?
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=2618253
I dont understand... When i start multiloader.exe it seems to go.. But i can only download update.app file with che left One button.the center button let me either download the ROM and the right button keep the tool off. What i have to do for use this magic program?

[Q] Bricked Ascend P6 after flashing recovery

Hi There, I Tried To Install The TWRP Recovery Using Recovery Tools - Flasher, It Succeeded, And Asked To Reboot My Phone, Now My Huawei Ascend P6 Is Not Booting, Its Stuck On The "Huawei Ascend" Screen, I Cant Access Recory Or Booot My Phone. Can You Help Me Please?
You should have followed the tutorials to flash TWRP on here... Does adb recognize your phone?
Sent from my P6-U06 using XDA Premium 4 mobile app
lootjelo said:
You should have followed the tutorials to flash TWRP on here... Does adb recognize your phone?
Sent from my P6-U06 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
I Tried And It Didnt Work, Kept On Getting Stuck On Waiting For Device, And No, adb Cant See My Phone
If you can't boot into any mode, your best bet would be bringing it to service and playing dumb about as to why your phone is bricked...
Sent from my P6-U06 using XDA Premium 4 mobile app
lootjelo said:
If you can't boot into any mode, your best bet would be bringing it to service and playing dumb about as to why your phone is bricked...
Sent from my P6-U06 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
Isnt There Anything Else I Can Try Before Taking It To Service? I Live Too Far From The Nearest Store I Can take It To, It Would Cost a Lot For Me To Take It There.
mcselowa said:
Isnt There Anything Else I Can Try Before Taking It To Service? I Live Too Far From The Nearest Store I Can take It To, It Would Cost a Lot For Me To Take It There.
Click to expand...
Click to collapse
I really wouldn't know: you can't boot into recovery and adb doesn't recognise it... Did you install the drivers for your phone on your pc? Try installing HiSuite... Then check if adb recognises your phone.
Sent from my amazing Ascend P6
lootjelo said:
I really wouldn't know: you can't boot into recovery and adb doesn't recognise it... Did you install the drivers for your phone on your pc? Try installing HiSuite... Then check if adb recognises your phone.
Sent from my amazing Ascend P6
Click to expand...
Click to collapse
I Have HiSuite, But Before My Phone Got Bricked, HiSuite Could See It, But adb Couldnt, Now Both Cant See It
mcselowa said:
I Have HiSuite, But Before My Phone Got Bricked, HiSuite Could See It, But adb Couldnt, Now Both Cant See It
Click to expand...
Click to collapse
Sorry man: then I wouldn't know what to do anymore...
Sent from my amazing Ascend P6.
Powered by MIUI v5.
mcselowa said:
I Have HiSuite, But Before My Phone Got Bricked, HiSuite Could See It, But adb Couldnt, Now Both Cant See It
Click to expand...
Click to collapse
Have you tried using the 3 buttons combo to flash stock firmware?
Download any UPDATE.APP put inside your sdcard inside a folder named dload so it should look like:
sdcard/dload/UPDATE.APP
Then just keep pressing Power+Volume UP+Volume Down buttons at the same time. this will force your phone to to into recovery (either TWRP or Stock). If this does not work try the following.
While Pressing both Power+Volume Down buttons connect your phone to the PC, it will look like the phone is again "stucked" in Huawei Ascend Logo, then usging a cmd inside the fastboot and adb folder type
fastboot devices
If you get any reply from cmd just flash twrp recovery again (manually this time)
How can he try update.app solution if he has custom recovery, he does not have a stock recovery, so your solution is pointless.
dekosteka said:
How can he try update.app solution if he has custom recovery, he does not have a stock recovery, so your solution is pointless.
Click to expand...
Click to collapse
Pointless?
Have actually read what I wrote? He said, the program he used told him it succeed and now his phone is stuck. So it migth have worked or not, meaning that TWRP might or not be succesfully installed in his phone. And I also wrote that if that doesn't work (Meaning he can't boot to recovery by the combo) he can try to reboot the phone to fastboot and flash again either TWRP or Stock Recovery back to the phone...
So your reply was the pointless one here, not mine...
jimbo77 said:
Have you tried using the 3 buttons combo to flash stock firmware?
Download any UPDATE.APP put inside your sdcard inside a folder named dload so it should look like:
sdcard/dload/UPDATE.APP
Then just keep pressing Power+Volume UP+Volume Down buttons at the same time. this will force your phone to to into recovery (either TWRP or Stock). If this does not work try the following.
While Pressing both Power+Volume Down buttons connect your phone to the PC, it will look like the phone is again "stucked" in Huawei Ascend Logo, then usging a cmd inside the fastboot and adb folder type
fastboot devices
If you get any reply from cmd just flash twrp recovery again (manually this time)
Click to expand...
Click to collapse
I Tried The 2nd Option And The Phone Appears On My PC As Android Single ADB Interface, And After Attempting The Command All I Got Was What is On The Picture I Attached
mcselowa said:
I Tried The 2nd Option And The Phone Appears On My PC As Android Single ADB Interface, And After Attempting The Command All I Got Was What is On The Picture I Attached
Click to expand...
Click to collapse
That's fine! That means your phone is booting into fastboot.
So now you should try to manually install TWRP to the phone just download TWRP recovery from this Thread:
http://forum.xda-developers.com/showthread.php?t=2534420
make sure to download latest version, and then rename it to twrp-recovery.img
After that put the file inside the folder where you have fastboot and adb.
type again fastboot devices and make sure you get the same output from CMD (a lot of ? signs)
and then type:
fastboot flash recovery twrp-recovery.img
after that
fastboot reboot
the phone will try to boot into system, if it fails try the three button combo and the you should be able to boot into TWRP Recovery.
Good Luck!
jimbo77 said:
That's fine! That means your phone is booting into fastboot.
So now you should try to manually install TWRP to the phone just download TWRP recovery from this Thread:
http://forum.xda-developers.com/showthread.php?t=2534420
make sure to download latest version, and then rename it to twrp-recovery.img
After that put the file inside the folder where you have fastboot and adb.
type again fastboot devices and make sure you get the same output from CMD (a lot of ? signs)
and then type:
fastboot flash recovery twrp-recovery.img
after that
fastboot reboot
the phone will try to boot into system, if it fails try the three button combo and the you should be able to boot into TWRP Recovery.
Good Luck!
Click to expand...
Click to collapse
Im Now Trying To Flash The Recovery, @ 1st It Says Failed(Remote: Flash Failure, errno2) Second Time I Typed Fastboot devices again And It Returns ??????????? Fastboot, Which Is Diff From Previous Result. Then I Try To Flash Again And Its Stuck Saying : Sending 'recovery' (8262)...
mcselowa said:
Im Now Trying To Flash The Recovery, @ 1st It Says Failed(Remote: Flash Failure, errno2) Second Time I Typed Fastboot devices again And It Returns ??????????? Fastboot, Which Is Diff From Previous Result. Then I Try To Flash Again And Its Stuck Saying : Sending 'recovery' (8262)...
Click to expand...
Click to collapse
If TWRP fails try to flash stock recovery just name the file as recovery.img and use
fastboot flash recovery recovery.img
if that also fails, the I guess you last chance is to take to a repair center my friend...
jimbo77 said:
If TWRP fails try to flash stock recovery just name the file as recovery.img and use
fastboot flash recovery recovery.img
if that also fails, the I guess you last chance is to take to a repair center my friend...
Click to expand...
Click to collapse
Thank You Soo Much, It Finally Worked, I Changed Cables And It Worked. I Am So Grateful Right Now!
does it works for mate in b907 (4.2.2) ?
Thx

[Q] [Help?] Huawei p6 softbrick (rooted/TWRP, need to transfer ROM)

Hi guys,
I would really appreciate any help getting out of this pickle (my first time trying to install a ROM).
Here's the situation:
- Running a Huawei P6-C00 Chinese phone
- Was interested in trying a custom ROM (e.g. CleanRom by @surdu_petru) in order to enable Google Apps
- Updated normally to B120 CN as instructed
- Rooted (using Root Wizard)
- Installed customer recovery (TWRP 2.6.3.3)
- Started flash process including advanced wipe in TWRP... wiped system, cache, davlik, etc... :crying:
- Realized that I didn't have the ROM .zip copied to the phone yet
Currently, I'm able to boot into TWRP but cannot connect using adb for sideload (TWRP just says starting sideload but never connects). What do you guys recommend? I don't have a backup of any working ROM or the stock image.
Is there a way to initiate a "standard" restore since I wiped all the caches? ...
Are there some tricks to getting ADB running so I can try to sideload the ROM again? ...
P6-C00 does not have an SD card, but is it possible to load the ROM onto a USB and read it from TWRP?
Thanks for any help!
Did u try connecting to adb?
Sent from my U9200 using XDA Premium 4 mobile app
some help
onetree said:
Hi guys,
I would really appreciate any help getting out of this pickle (my first time trying to install a ROM).
Here's the situation:
- Running a Huawei P6-C00 Chinese phone
- Was interested in trying a custom ROM (e.g. CleanRom by @surdu_petru) in order to enable Google Apps
- Updated normally to B120 CN as instructed
- Rooted (using Root Wizard)
- Installed customer recovery (TWRP 2.6.3.3)
- Started flash process including advanced wipe in TWRP... wiped system, cache, davlik, etc... :crying:
- Realized that I didn't have the ROM .zip copied to the phone yet
Currently, I'm able to boot into TWRP but cannot connect using adb for sideload (TWRP just says starting sideload but never connects). What do you guys recommend? I don't have a backup of any working ROM or the stock image.
Is there a way to initiate a "standard" restore since I wiped all the caches? ...
Are there some tricks to getting ADB running so I can try to sideload the ROM again? ...
P6-C00 does not have an SD card, but is it possible to load the ROM onto a USB and read it from TWRP?
Thanks for any help!
Click to expand...
Click to collapse
you can try it whith a linux pc (ubuntu)
i have the same problem
good luck!
onetree said:
Hi guys,
I would really appreciate any help getting out of this pickle (my first time trying to install a ROM).
Here's the situation:
- Running a Huawei P6-C00 Chinese phone
- Was interested in trying a custom ROM (e.g. CleanRom by @surdu_petru) in order to enable Google Apps
- Updated normally to B120 CN as instructed
- Rooted (using Root Wizard)
- Installed customer recovery (TWRP 2.6.3.3)
- Started flash process including advanced wipe in TWRP... wiped system, cache, davlik, etc... :crying:
- Realized that I didn't have the ROM .zip copied to the phone yet
Currently, I'm able to boot into TWRP but cannot connect using adb for sideload (TWRP just says starting sideload but never connects). What do you guys recommend? I don't have a backup of any working ROM or the stock image.
Is there a way to initiate a "standard" restore since I wiped all the caches? ...
Are there some tricks to getting ADB running so I can try to sideload the ROM again? ...
P6-C00 does not have an SD card, but is it possible to load the ROM onto a USB and read it from TWRP?
Thanks for any help!
Click to expand...
Click to collapse
Did you try it with fastboot?
Gesendet von meinem P6-U06 mit Tapatalk
ext4
taaeem said:
Did you try it with fastboot?
Gesendet von meinem P6-U06 mit Tapatalk
Click to expand...
Click to collapse
i know that he must use a linux pc that for the drivers
ext4 If say it right...
taaeem said:
Did you try it with fastboot?
Click to expand...
Click to collapse
Hi Taaeem,
Thanks for the hint. I read some posts on fastboot and tried the following, but could not get into fastboot mode.
Methods I tried
- Power off phone and then power on while holding vol-down button
- Select Reboot -> System option from TWRP, while holding volume down
- Select Reboot -> Bootloader option from TWRP
From what I understand, fastboot mode should be run from the /boot partition, which I didn't wipe. So any ideas how I can get into fastboot mode?
Thanks again!
Okay, I confirmed that I have at least some kind of fastboot access because I tried "fastboot reboot-bootloader" from command prompt on my PC, and it rebooted the phone (but the phone stayed on boot logo).
- Next time I get fastboot, should I run "fastboot flash [partition] [ROM-file.zip]"?
- If so, what partition should I specify? I'm confused about where this command will send the ROM file, and if so how do I find it from TWRP later on in order to install it?
Thank you!
One more update:
- Even though I'm stuck at boot logo when I try to enter fastboot mode, it looks like there is a somewhat working fastboot connection. I tried running "fastboot flash [partition] ROM.zip" but it fails after 16s ("remote: flash write failure" or "remote: partition does not exist"). I tried flashing to cache / data / system
Should I try @N!ELS huawei p6 suggestion of accessing by Linux? (I don't have one nearby) or am I using fastboot wrong?
Thanks!!
Also:
- I noticed that when I boot into TWRP the device shows as "..." in my system tray USB devices list.
- When I try to boot into fastboot mode, the device shows as "Android Sooner Single ADB Interface" (but phone is still stuck on boot logo)
- However I'm still not able to connect using ADB .. shows "error: device not found" in all cases)
- Finally, after powering off the phone does show the stock charging animation, which gives me hope that this can still be saved :crying:
onetree said:
One more update:
- Even though I'm stuck at boot logo when I try to enter fastboot mode, it looks like there is a somewhat working fastboot connection. I tried running "fastboot flash [partition] ROM.zip" but it fails after 16s ("remote: flash write failure" or "remote: partition does not exist"). I tried flashing to cache / data / system
Should I try @N!ELS huawei p6 suggestion of accessing by Linux? (I don't have one nearby) or am I using fastboot wrong?
Thanks!!
Also:
- I noticed that when I boot into TWRP the device shows as "..." in my system tray USB devices list.
- When I try to boot into fastboot mode, the device shows as "Android Sooner Single ADB Interface" (but phone is still stuck on boot logo)
- However I'm still not able to connect using ADB .. shows "error: device not found" in all cases)
- Finally, after powering off the phone does show the stock charging animation, which gives me hope that this can still be saved :crying:
Click to expand...
Click to collapse
fastboot mode on the P6 doesn't have any kind of ui for fastboot, so it stays on the boot logo, fastboot should work fine.
You could always find an USB OTG cable and connect a FAT32 partitioned mem stick with the .zip on it, TWRP allows flashing from USB memory as far as I know
You are definetely not out of hope, but im not sure about the compability of P6-U06 roms with the C00 variant.
onetree said:
One more update:
- Even though I'm stuck at boot logo when I try to enter fastboot mode, it looks like there is a somewhat working fastboot connection. I tried running "fastboot flash [partition] ROM.zip" but it fails after 16s ("remote: flash write failure" or "remote: partition does not exist"). I tried flashing to cache / data / system
Click to expand...
Click to collapse
Obviously you can't flash the whole zip file to every partition, infact you can't flash a .zip at all, atleast not in fastboot mode, .img extension is used. So don't try flashing the rom manually via fastboot, since you have a high risk of actually bricking the device, if not in the right hands.
Also when booted into TWRP, try "adb devices" in the cmd see if anything shows up.
onetree said:
One more update:
- Even though I'm stuck at boot logo when I try to enter fastboot mode, it looks like there is a somewhat working fastboot connection. I tried running "fastboot flash [partition] ROM.zip" but it fails after 16s ("remote: flash write failure" or "remote: partition does not exist"). I tried flashing to cache / data / system
Should I try @N!ELS huawei p6 suggestion of accessing by Linux? (I don't have one nearby) or am I using fastboot wrong?
Thanks!!
Also:
- I noticed that when I boot into TWRP the device shows as "..." in my system tray USB devices list.
- When I try to boot into fastboot mode, the device shows as "Android Sooner Single ADB Interface" (but phone is still stuck on boot logo)
- However I'm still not able to connect using ADB .. shows "error: device not found" in all cases)
- Finally, after powering off the phone does show the stock charging animation, which gives me hope that this can still be saved :crying:
Click to expand...
Click to collapse
Okay that's good when you are stuck at the logo and you can see your device at your PC you are in fastboot mode, from here you can work with fastboot commands NOT with ADB that will not work. Anyway isn't there a option in TWRP where you can mount your device to USB when that work you can just copy the files on your phone without to go with fastboot. When that don't work you must try to extract the .zip from the ROM you want to install and flash every image with fastboot I think that should work.
Gesendet von meinem P6-U06 mit Tapatalk
tauio111 said:
fastboot mode on the P6 doesn't have any kind of ui for fastboot, so it stays on the boot logo, fastboot should work fine.
You could always find an USB OTG cable and connect a FAT32 partitioned mem stick with the .zip on it, TWRP allows flashing from USB memory as far as I know
You are definetely not out of hope, but im not sure about the compability of P6-U06 roms with the C00 variant.
Obviously you can't flash the whole zip file to every partition, infact you can't flash a .zip at all, atleast not in fastboot mode, .img extension is used. So don't try flashing the rom manually via fastboot, since you have a high risk of actually bricking the device, if not in the right hands.
Also when booted into TWRP, try "adb devices" in the cmd see if anything shows up.
Click to expand...
Click to collapse
Okay so now I'm a bit paranoid about hard-bricking the device, and would rather not try my luck on a ROM that isn't approved for the P6-C00, haha...
At this point I just want to get a working OS installed (restore to the default for P6-C00 phone, even), and then maybe try to safely enable Google Apps. Any suggestions on how I can get this restored?
- I think the device came with a USB cable that is OTG.
- Seems like fastboot is also working, even though "fastboot getvar xxx" returns nothing useful
- ADB does not work while booted into TWRP (can't run shell, sideload, or list devices)
onetree said:
Okay so now I'm a bit paranoid about hard-bricking the device, and would rather not try my luck on a ROM that isn't approved for the P6-C00, haha...
At this point I just want to get a working OS installed (restore to the default for P6-C00 phone, even), and then maybe try to safely enable Google Apps. Any suggestions on how I can get this restored?
- I think the device came with a USB cable that is OTG.
- Seems like fastboot is also working, even though "fastboot getvar xxx" returns nothing useful
- ADB does not work while booted into TWRP (can't run shell, sideload, or list devices)
Click to expand...
Click to collapse
Download this rom for example https://disk.yandex.com/public/?hash=bhDlIAc5AqKh4RAB2IdatPdEfYVI9FH/Zky/UTGcH3M=
Extract the .z7 and run the flash_all.bat, this scripts flashes the rom via fastboot and you should get your device back up and running again. And from there you can update to a newer firmware version without problems.
If the bat doesn't work try this:
boot to fastboot
fastboot flash system system.img
fastboot flash cust cust.img
fastboot reboot recovery
Wipe cache and dalvik cache in twrp
tauio111 said:
Download this rom for example https://disk.yandex.com/public/?hash=bhDlIAc5AqKh4RAB2IdatPdEfYVI9FH/Zky/UTGcH3M=
Extract the .z7 and run the flash_all.bat, this scripts flashes the rom via fastboot and you should get your device back up and running again. And from there you can update to a newer firmware version without problems.
If the bat doesn't work try this:
boot to fastboot
fastboot flash system system.img
fastboot flash cust cust.img
fastboot reboot recovery
Wipe cache and dalvik cache in twrp
Click to expand...
Click to collapse
Thank you! I will try this tonight after work
tauio111 said:
Download this rom for example https://disk.yandex.com/public/?hash=bhDlIAc5AqKh4RAB2IdatPdEfYVI9FH/Zky/UTGcH3M=
Extract the .z7 and run the flash_all.bat, this scripts flashes the rom via fastboot and you should get your device back up and running again. And from there you can update to a newer firmware version without problems.
If the bat doesn't work try this:
boot to fastboot
fastboot flash system system.img
fastboot flash cust cust.img
fastboot reboot recovery
Wipe cache and dalvik cache in twrp
Click to expand...
Click to collapse
Thanks, tauio111! That worked and I now have a working phone again :victory:
I'm going to be a bit more careful about how to enable Google Apps... this is too much stress during the workweek haha.
Later on what do you think my best option would be?
- Wait for a confirmed easy to install ROM for P6-C00 that supports Google Apps
- Some other way to enable Google Apps with the standard firmware, since I am rooted?
Thanks :laugh:
onetree said:
Thanks, tauio111! That worked and I now have a working phone again :victory:
I'm going to be a bit more careful about how to enable Google Apps... this is too much stress during the workweek haha.
Later on what do you think my best option would be?
- Wait for a confirmed easy to install ROM for P6-C00 that supports Google Apps
- Some other way to enable Google Apps with the standard firmware, since I am rooted?
Thanks :laugh:
Click to expand...
Click to collapse
Easy, flash this via TWRP
tauio111 said:
Easy, flash this via TWRP
Click to expand...
Click to collapse
Thanks @tauio111 and everyone else who helped debug this.
I flashed stock recovery, updated official firmware to B120, re-flashed TWRP, flashed gapps, and now have a working phone with Gmail and Play Store!! :silly:
tauio111 said:
Download this rom for example https://disk.yandex.com/public/?hash=bhDlIAc5AqKh4RAB2IdatPdEfYVI9FH/Zky/UTGcH3M=
Extract the .z7 and run the flash_all.bat, this scripts flashes the rom via fastboot and you should get your device back up and running again. And from there you can update to a newer firmware version without problems.
If the bat doesn't work try this:
boot to fastboot
fastboot flash system system.img
fastboot flash cust cust.img
fastboot reboot recovery
Wipe cache and dalvik cache in twrp
Click to expand...
Click to collapse
I have the same problem and i do the same but nothing..
I tried to delete xposed installer and my phone stuck..
What can i do?
Edit:It s opened but i can t touch my screen.I try to put my password and i can t..
tauio111 said:
Download this rom for example (Removed to allow posting - faye2thesky)
Extract the .z7 and run the flash_all.bat, this scripts flashes the rom via fastboot and you should get your device back up and running again. And from there you can update to a newer firmware version without problems.
If the bat doesn't work try this:
boot to fastboot
fastboot flash system system.img
fastboot flash cust cust.img
fastboot reboot recovery
Wipe cache and dalvik cache in twrp
Click to expand...
Click to collapse
Heya Tauio111, I'm having the same problem as onetree and I've been frying my mind over this for the past 4 days before I came across your solution. I found that your link is no longer working, may I ask what that ROM is and where else I may find it? Thanks!
faye2thesky said:
Heya Tauio111, I'm having the same problem as onetree and I've been frying my mind over this for the past 4 days before I came across your solution. I found that your link is no longer working, may I ask what that ROM is and where else I may find it? Thanks!
Click to expand...
Click to collapse
A way that may help (i've done it with boot&recovery images). Using this tool http://forum.xda-developers.com/showthread.php?t=2433454 , might give you the *.img files necesary for flashing the stock rom through fast boot. All you need is to follow the instructions on the tool and have a stock rom (update.app file type), and some knowledge on how to use the fastboot.
Hi Guys,
I kinda did the same thing here.
I accidently wiped my system with TWRP v2.6.3.7
I also have a huawei ascend p6 u06
I didn't realize i never copied a rom to my device so i don't know how to install.
I can't seem to be able to use adb or fastboot and my device is not picked up by windows (8.1), it just says removable disk in my computer.
and under device manager it says P6-U06 under unknown devices.
I have tried to install a bunch of different drivers to attempt something but no luck.
Please help me.

I badly need help

I have the Zenfone 2 and it is stuck in bootloop.
My brother boot it to CWM and flashed Paranoid Android without unlocking the bootloader and flashing TWRP. Now the phone stuck in bootloop, i tried flashing system.img the stock one but it is telling me that system.img cannot be loaded. What should i do? It is now bootlooping. I dont know what to do.
ebanreb37 said:
I have the Zenfone 2 and it is stuck in bootloop.
My brother boot it to CWM and flashed Paranoid Android without unlocking the bootloader and flashing TWRP. Now the phone stuck in bootloop, i tried flashing system.img the stock one but it is telling me that system.img cannot be loaded. What should i do? It is now bootlooping. I dont know what to do.
Click to expand...
Click to collapse
Hi, I unfortunatelly am not able to solve your Problem, but maybe you could help me with mine. Could you pls upload the System.img? I am only able to find *.zip and adb doesn´t want to Flash it at all
Thanx in advance
Blubber120 said:
Hi, I unfortunatelly am not able to solve your Problem, but maybe you could help me with mine. Could you pls upload the System.img? I am only able to find *.zip and adb doesn´t want to Flash it at all
Thanx in advance
Click to expand...
Click to collapse
Go to Original Android developement. It's in the pre-rooted thread, these are the ONLY img files for roms available unless you push the zip file using ADB...
Flash the system zip file rather than trying to flash simply the .img. The zip files are in this thread (http://forum.xda-developers.com/zenfone2/development/asus-zenfone-2-rom-t3054956) and might help because you're also flashing default recovery... could be CWM.
Also try flashing using fastboot.
your phone model?
ze55m1
Rma
What worked with me, Problem is simmilar, I flaged the Boot.img and androidboot.img, which Werke attached in the custim Rom folder, too. Without that, I gut stuck at the Boot Logo, now all works fine and I am trying to be up to date with the Roms.
Blubber120 said:
What worked with me, Problem is simmilar, I flaged the Boot.img and androidboot.img, which Werke attached in the custim Rom folder, too. Without that, I gut stuck at the Boot Logo, now all works fine and I am trying to be up to date with the Roms.
Click to expand...
Click to collapse
1. download the latest recovery from here https://dl.twrp.me/Z00A/ and firmware from here http://dlcdnet.asus.com/pub/ASUS/ZenFone/ZE551ML/UL-Z00A-WW-2.20.40.97-user.zip
2. download and install adb and fastboot driver from here http://forum.xda-developers.com/showthread.php?t=2317790 and intel usb drivers from here https://software.intel.com/en-us/android/articles/intel-usb-driver-for-android-devices
3.the adb driver should have installed in your pc OS drive [ which is C: ] put the downloaded recovery and firmware in that folder [where adb is installed] then in that folder, open command window by pressing shift and right click and a dialogue box will appear then open the command window from there and enter this command fastboot flash recovery {name of the recovery twrp something}.img then connect your phone to your pc and enter bootloader in your phone and press enter in command window.
4.after that put the downloaded firmware in any sdcard and put it in your phone then open recovery mode in your phone and go to reboot>recovery [yeah you have to reboot the recovery] then when recovery open again then go to wipe>advanced wipe> and select system,data,cache,dalvik and internal storage [internal storage is optional but if you choose it then it will wipe all your data in your phone] then wipe it and go to install section then choose the extsdcard [it should be written internal storage click on that then you can choose your external storage] then in the extstorage choose the firmware you downloaded and just swipe to flash.
5.patience ..because it would take time and maybe get stuck at 52% or 59% ..so just let it take time for installation [btw connect your phone to thr charger in this process]
6.after it done then reboot your phone and ALL DONE. [the first boot will take some mins to boot up]
Sent from my ASUS_Z00A

Phone completely bricked

Hi everyone !
Yesterday, I wanted to wipe cache for some reasons, and I stupidly restarted the phone while formatting cache.
Result :
-A bootloop at the firt restart, then a "Error !"
-Can't acces Recovery mode, "Error !". I tried power button+volum up, don't work.
-ADB don't work anymore, I can't see the phone via adb devices
The only thing I can do is execute fastboot commands in Windows. I successfully made a tethered TWRP recovery, but I seriously don't know what to do from here. I tried flahsing a ROM, but it didn't worked (still have Error !).
I tried install permanent TWRP (unofficial), but I can't acces it. Probably because my bootloader is locked.
So... what should I do ?
Fastboot format cache should do the trick.
KillerNo2 said:
Fastboot format cache should do the trick.
Click to expand...
Click to collapse
I tried it.
Still don't start correctly, don't forget that I did some **** to try to fix it :s
The ROM is probably also damaged...
EDIT : Now it don't show the Error ! anymore, it always return to fastboot mode...
Baldriksen said:
I tried it.
Still don't start correctly, don't forget that I did some **** to try to fix it :s
The ROM is probably also damaged...
EDIT : Now it don't show the Error ! anymore, it always return to fastboot mode...
Click to expand...
Click to collapse
After formating cache you should've been able to get into recovery mode, if not, download recovery image from here then:
fastboot flash recovery recovery.img
fastboot flash boot boot.img
fastboot flash fastboot droidboot.img
You can always sideload stock roms from there.
KillerNo2 said:
After formating cache you should've been able to get into recovery mode, if not, download recovery image from here then:
fastboot flash recovery recovery.img
fastboot flash boot boot.img
fastboot flash fastboot droidboot.img
You can always sideload stock roms from there.
Click to expand...
Click to collapse
I get this :
">fastboot flash F:\recovery.img
unknown partition 'F:\recovery.img'
error: cannot determine image filename for 'F:\recovery.img'"
EDIT : oh **** sorry i misswrited the command é_è
EDIT 2 : THANKS ! I have acces to normal recovery. Can you tell me what should I do now ? (seriously don't want to make everything goes brick again ^^')
Baldriksen said:
I get this :
">fastboot flash F:\recovery.img
unknown partition 'F:\recovery.img'
error: cannot determine image filename for 'F:\recovery.img'"
Click to expand...
Click to collapse
Put all image files into the adb folder.
KillerNo2 said:
Put all image files into the adb folder.
Click to expand...
Click to collapse
Sorry, I edited my message, the error was from me.
So now I am on recovery... what should I do ?
Baldriksen said:
Sorry, I edited my message, the error was from me.
So now I am on recovery... what should I do ?
Click to expand...
Click to collapse
Download stock ROM from Asus site, and then sideload the ROM in recovery mode. Follow 3.2) Flashing Zenfone 2 via ADB in this thread.
KillerNo2 said:
Download stock ROM from Asus site, and then sideload the ROM in recovery mode.
Click to expand...
Click to collapse
Sideload with "Apply update from ADB" ?
The stock ROM is a zip of about 1.1GB ? I heard that their were update only package and full firmware ?
Baldriksen said:
Sideload with "Apply update from ADB" ?
The stock ROM is a zip of about 1.1GB ? I heard that their were update only package and full firmware ?
Click to expand...
Click to collapse
That zip file is a full firmware.
Thanks !
I did it and I have now the stock firmware installed correctly !
I have the same problem... But there is no option to fastboot format cache... only normal boot, power off, recovery mode... can't enter recovery mode either...
ndruqltn said:
I have the same problem... But there is no option to fastboot format cache... only normal boot, power off, recovery mode... can't enter recovery mode either...
Click to expand...
Click to collapse
You need to follow the steps in this thread to install drivers and adb package first. Fast boot firmat cache is the command that you should type in on your PC.
Just a thought but instead of trying to install anything through adb why not instal a pre-rooted rom img through fastboot too. You can always wipe out root with the next OTA...
I have already wipe cache and now boots up properly but the problem is that touch screen doesn't seem to work...
Can't connect my Zenfone 2 to my pc even though I have installed drivers and adb...

Categories

Resources