Boot repair for GT-I9301I - Galaxy S3 Neo General

Hello!
If your I9301I
No Power on !
Unable to enter download mode !
Boot recovery after memory replacement !
I found solution how to fix it!
Bootloader, PIT file and Odin 3.09

godhamer said:
Hello!
If your I9301I
No Power on !
Unable to enter download mode !
Boot recovery after ...
Click to expand...
Click to collapse
And how do i download this "bootloader, pit file, odin" ?

As was for i9300. But as it states. After memory replacement. Which is a very hard thing to do
You have do desolder the old memory chip from pcb and put another one in its place.
After that you'll also might be needing Samsung's proprietary box-jig to provide power to phone (might not. For some it was doable with any UART providing box and if I remember 301k cable)
So if it dies either good luck fixing it or send it to Sammy to fix it.

Download a firmware in sammobile and then flash it by odin

not working its says all threads completed(succeed 0/failed 1)

Related

Note 4 PIT Files For Repartiton [F/C/T/W8]

I see a lot of users with partition problems like read and write errors and a lot more
People who need to re partition their note 4 can do so now
so i have decided to post the PIT files in my possession so everyone can have a smoother note 4 experience
Steps to flash PIT files in Odin (Have latest ODIN)
1. Boot the Galaxy Note 4 into download mode screen then connect to PC.
2. This time load the N910F/C/T/W8.pit Pit file on Odin’s PIT Button (Select pit file of your variant) (SPECIAL INSTRUCTIONS FOR C Variant SEE POST 2)
3. Load your original stock firmware on the Odin’s AP button.
4 Make sure repartiton is automatically checked in options
5. Click on “Start” to flash the stock firmware and PIT file then wait.
After the process is over
Turn off the phone and set it into recovery mode
– Press volume “volume up, home and power buttons”
– Once in recovery mode, perform full wipe
– Select ‘wipe data/factory reset’
All Files are in one zip
Only select your variant and DO NOT CROSS FLASH
Special instructions for C Variant of note 4
Make sure you flash The SM-N910C OLB (CSC) firmware before you repartition as apparently for this variant has different pit files for different firmwares)
OLB IS THE CSC CODE OF THE FIRMWARE
Example for the type firmware you need
http://www.sammobile.com/firmwares/download/60071/N910CXXU2COJ5_N910COLB2COJ5_XXV/
You can try flashing this pit with other firmwares you may have but beware you have been warned
Thank you for the PIT file. I want to re-partition my N910F, but what it means "cross flash" ? Thank you.
NEVER flash this file without rom. My phone got mad and didnt recognize ext sdcard or phone storage.. Trying to fix it at the moment..
E: I flashed the stock rom with pit file, after that I flashed TWRP + Nameless Rom. THIS IS DAMN SMOOTH NOW!
Thank you for wat you do. It work's great.
Request
Please Made one for SM-N910G..
Please make n910h. Really into the wiping / repartition my phone
Hi, i have this problem
I was install CM13 for my SM: N910C but didn't like it so, i reboot into recovry and do full wipe then flashed SIX6 and reboot i have my N910C stoped on (samsung galaxy note 4)
And not start up so, i flashed my Official soft from sammobile but did't do anything i have stop on (samsung note 4) not ( samsung logo)
So, did u think it will solved by this method? Or what?
Thanx.
ty for olb pit.
When do i need to repartition? and why it will be smoother...if someone can explain thanks.
Can somebody upload the PIT file for SM-910G Indian variant. I am on COL3, it says data partition is corrupt. Please help! I flashed the Singapore XSP Pit file and now phone doesn't go to stock recovery, only download mode accessible.
vighneshpillai90 said:
Can somebody upload the PIT file for SM-910G Indian variant. I am on COL3, it says data partition is corrupt. Please help! I flashed the Singapore XSP Pit file and now phone doesn't go to stock recovery, only download mode accessible.
Click to expand...
Click to collapse
Hi vighneshpillai90, apologies I don't have the pit file you're requesting, but I'm using the Singapore 910G and having the same problem as you.... I need the Pit file for it (I can't find it anywhere). Could u please share it here?
Thanks so much!
Note 4 PIT File for Singapore XSP variant
den80001 said:
Hi vighneshpillai90, apologies I don't have the pit file you're requesting, but I'm using the Singapore 910G and having the same problem as you.... I need the Pit file for it (I can't find it anywhere). Could u please share it here?
Thanks so much!
Click to expand...
Click to collapse
Here You go,
1. Use Odin v3.10
2. OPTIONAL - Incase you need to format emmc, select clear nand partition (only if you experience data/system partition corrupted error). This can be done only while flashing Stock Rom TAR file.
3. Make sure you select both the PIT and PBA files (So that both repartioning and installation of stock rom is done in the same session).
4. Select Repartition and Flash the device.
5. Once rebooted you will get stuck at samsung logo, dont worry, just go to stock recovery and perform a factory reset and clear cache.
6. Might take upto 5mins, but works like a charm.
vighneshpillai90 said:
Here You go,
1. Use Odin v3.10
2. OPTIONAL - Incase you need to format emmc, select clear nand partition (only if you experience data/system partition corrupted error). This can be done only while flashing Stock Rom TAR file.
3. Make sure you select both the PIT and PBA files (So that both repartioning and installation of stock rom is done in the same session).
4. Select Repartition and Flash the device.
5. Once rebooted you will get stuck at samsung logo, dont worry, just go to stock recovery and perform a factory reset and clear cache.
6. Might take upto 5mins, but works like a charm.
Click to expand...
Click to collapse
Can you tell me the step for n910h? Thx
white7561 said:
Can you tell me the step for n910h? Thx
Click to expand...
Click to collapse
Its exactly the same for every device, except just select the pit file corresponding to your device in step 3.
1000 thanks for pit file !
Ashwin Prabhunerurkar said:
I see a lot of users with partition problems like read and write errors and a lot more
People who need to re partition their note 4 can do so now
so i have decided to post the PIT files in my possession so everyone can have a smoother note 4 experience
Steps to flash PIT files in Odin (Have latest ODIN)
1. Boot the Galaxy Note 4 into download mode screen then connect to PC.
2. This time load the N910F/C/T/W8.pit Pit file on Odin’s PIT Button (Select pit file of your variant) (SPECIAL INSTRUCTIONS FOR C Variant SEE POST 2)
3. Load your original stock firmware on the Odin’s AP button.
4 Make sure repartiton is automatically checked in options
5. Click on “Start” to flash the stock firmware and PIT file then wait.
After the process is over
Turn off the phone and set it into recovery mode
– Press volume “volume up, home and power buttons”
– Once in recovery mode, perform full wipe
– Select ‘wipe data/factory reset’
All Files are in one zip
Only select your variant and DO NOT CROSS FLASH
Click to expand...
Click to collapse
I rot every my android phone and play with mods etc ...doing that last 6 years and everything was fine until couple days ago I flashed note 5 port Kyubi on my Samsung galaxy note 4 and was working awesome until 2 days ago my phone didn't want to charge I try ed with 5 others cables and chargers .I tryed factory reset , flash couple times stock Samsung firmware in odin and problem was persis, I try ed pull batery out and hod power button to drain electric out of device and also didn't help.
And than yesterday I find your pit file and flashed on my 910f and it working like a charm ...now I can carge again with what ever charger I pick and fast charging working too
Thank you so much !
hi can flash c pit file in n910h??
lfpeacemaker said:
hi can flash c pit file in n910h??
Click to expand...
Click to collapse
NOO . DONT.. sorry for caps. Its diffrent. The bootloader is diffrent too. Cause the diff modem file too
white7561 said:
NOO . DONT.. sorry for caps. Its diffrent. The bootloader is diffrent too. Cause the diff modem file too
Click to expand...
Click to collapse
Hi, thanks, will be a pit file for n910h?
lfpeacemaker said:
Hi, thanks, will be a pit file for n910h?
Click to expand...
Click to collapse
I dont have. But i see many on google. But im not risking my phone so yeah if u do found and test working. Please report and send to me
---------- Post added at 07:19 PM ---------- Previous post was at 06:34 PM ----------
lfpeacemaker said:
Hi, thanks, will be a pit file for n910h?
Click to expand...
Click to collapse
Okay. What is your csc? If like me. Im on indonesia so XSE. Whats yours

Samsung Galaxy S4 mini dead

hello guy's, my samsung today work's fine and from one hour not work at all - dead, i try to turn on no lucky, enter recovery no lucky, enter download mode not lucky
i found on forum about debrick.img and put on 16GB card, and phone vibrate and turn on but stuck like on the pictures mmc read failed, any sugestion, all the best
http://postimg.org/image/ar0zp4olp/
http://postimg.org/image/h3g4yyrnx/
gigidel said:
hello guy's, my samsung today work's fine and from one hour not work at all - dead, i try to turn on no lucky, enter recovery no lucky, enter download mode not lucky
i found on forum about debrick.img and put on 16GB card, and phone vibrate and turn on but stuck like on the pictures mmc read failed, any sugestion, all the best
http://postimg.org/image/ar0zp4olp/
http://postimg.org/image/h3g4yyrnx/
Click to expand...
Click to collapse
Sounds like the emmc memory is dead. Try to use these debrick images that I had taken from my i9195 some time ago. Extract first. https://drive.google.com/file/d/0B_vlSjY0nNrkX001ZUs4ZUF6dXc/view?usp=sharing
https://drive.google.com/file/d/0B_vlSjY0nNrkSFRVUERoTkF5cnM/view?usp=sharing
thanks a lot Mountains788, i try this two debrick.img, but no lucky, still the same mmc read failed
gigidel said:
thanks a lot Mountains788, i try this two debrick.img, but no lucky, still the same mmc read failed
Click to expand...
Click to collapse
I had the same issue, 2days ago (also so an Galaxy S4 mini).
I solved it by holding the 'volume down + home button' while connecting/disconnecting the phone to my/from laptop.
I have the same problem
When i put the sdcard with debrick image in my phone, It says:
BOOT RECOVERY MODE
CHECK BOOT PARTITONS..
COPY FROM T-FLASH..
BOOT RECOVERY..
WRITE 139008 sectors..
FLASH WRITE FAILURE
ddi : mmc_read failed
ODIN MODE
PRODUCT NAME: GT-I9190
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Custom
KNOX KERNEL LOCK: 0x0
KNOX WARRANTY VOID: 0x1
CSB-CONFIG-LSB: 0x30
BOOTLOADER RP SWREV: 2
WRITE PROTECTION: Enable
And when i connect it to pc to flash by odin, it says "There is no pit partition"
When i put the pit file in odin, it says the same
What should i do?
Did you get it to work? I have the exact same problem with the same phone (GT-I9190) !!!!

Note II GT-N7102 16GB Dual-Sim Soft-bricked Help (& files) needed

Symptoms:
1. Boot loop. GT-N7102 logo comes and the device reboots.
2. Can go to download mode. Model no. GT-N7102 is visible
3. Recovery mode-Android shows up for ~4 seconds and then phone reboots and goes into a boot-loop.
Was running N7102ZCUEOJ1_JB43_deodex_gapps_root_noknox_lite_by _neopunk88 (since March'16), when the phone suddenly decided to go into a boot-loop.
The phone was rooted. I had installed LSpeed the previous night and had set it to run in recommended mode.
What I have tried so far
1. Odin 3.07, 3.09 etc
2. stock recovery flash fails
2. tried to flash N7102ZCUEOJ1_N7102CHNEOJ1_N7102ZCUEML1_HOME.tar.md5 (last stock), but fails
3. After I had exhausted possibilities, tried the following pit files, one at a time, first from here and then here and then here along with the stock ROM. All pit files seem legit and the correct ones, but I have no way to verify. I have tried first without and then with re-partition option selected in Odin. Flash fails.
4. All drivers, USB ports and cable okay as I can flash my wife's S6.
Phone still going into download mode.
Odin fail modes
1. without pit file, while flashing either recovery or stock rom, Odil fails just after sboot.bin at NAND write-start.
2. with pit file and re-partition checked, Odin gets stuck in "get pit file for mapping"
3. with pit file but re-partition unchecked, Odin fails is the same as (1)
4. I have tried setting Odin compatibility to XP but it does not result in anything different. I haven't needed xp compatibility setting this while flashing anything before.
Please could I have some guidance on what options I have left and the files, if I am not using the correct ones?
My belief is that if I can get to the download mode, there has to be way to un-brick the phone..fingers crossed.
Thanks in advance.
UPDATE: Fixed phone by replacing the motherboard from here. Everything working fine now.
still waiting for a response..
@jam_27 It is possible that eMMC got corrupted. (it's a hardware fail)
If I were you I would try to flash TWRP. http://www.twrp.me - For N7100, as it doesn't matter for recovery.
READ: http://forum.xda-developers.com/galaxy-note-2/help/nt7100-wont-boot-wont-charge-recover-t3504290
Thanks, TWRP recovery flash fails at NAND write start.
jam_27 said:
Thanks, TWRP recovery flash fails at NAND write start.
Click to expand...
Click to collapse
Below the JTAG tool report from FoneFunShop UK
eMMC Flash Memory Chip is damaged
===============
= JTAG REPORT =
===============
Open serial port...OK
Connecting to the RIFF Box...OK
Connecting to the dead body...OK
Detected dead body: DETECTED
Set I/O Voltage reads OK, TCK Frequency is OK
Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK
Flashing the dead body...
No Resurrection Data is available for the eMMC Chip with Capacity = 0B
ERROR: Failed use to Resurrection Data for the eMMC Chip with Capacity = 0B
ERROR: Selected FLASH Chip was not initialized by the DCC Loader.
----
I wont be able to replace the emmc chip myself (don't have the correct tools) but should be able to replace the motherboard.
Any other suggestions before I open up the until.

Note 2 GT-N7100 stuck on boot screen

Hi, i have a problem with my phone,latest stock rom,no root,i found it stuck on boot screen after i use a non original cable with original charger, is SDS or i can fix it? when i try to use odin with stock rom i get nand write fail everytime ,i see the phone conected in device manager(photo) , in recovery i see red errors and when i enter in download mode odin see the phone but is unable to write, can you help me to fix this or any solution to fix it with usb or sd card only because i dont have profesional tools (box)? thanks
What is the Odin error? You can see it in the log.
audit13 said:
What is the Odin error? You can see it in the log.
Click to expand...
Click to collapse
nand write start fail
What file is Odin trying to flash when it fails?
audit13 said:
What file is Odin trying to flash when it fails?
Click to expand...
Click to collapse
with heimdall-suite i extract the pit file from the phone successful but i unable to write, adb slideload is recognized with adb,any command to send via adb slideload or via download mode to mount the partitions? when i send a zip file via adb slideload i get unable to mount cache,with sd card boot recovery can i fix this?
Odin is failing when trying to flash sboot.bin because you are using the wrong ROM, the ROM has bootloader that is older than the bootloader in the phone, you need to use the original Samsung USB cable, or a different USB 2.0 port.
audit13 said:
Odin is failing when trying to flash sboot.bin because you are using the wrong ROM, the ROM has bootloader that is older than the bootloader in the phone, you need to use the original Samsung USB cable, or a different USB 2.0 port.
Click to expand...
Click to collapse
the stock rom i try to flash is the latest and same with the rom from the broken phone
Sounds like the memory chip is defective.
audit13 said:
Sounds like the memory chip is defective.
Click to expand...
Click to collapse
if i try this guide from the rar file can i fix it? i only need a bootloader dump file from a working n7100 with 4.4.2 firmware and then i write it on a sd card , this will repair the nand write fail? maybe the bootloader is corupt and is working after re write with sdcard mode.
If the nand is defective, no software is going to fix it.
If the bootloader was corrupt, Odin would flash over the existing bootloader could fix it.
Try this: flash twrp to the phone using Odin and then use TWRP to flash a CM ROM to see if the phone will boot with CM.
nand write start fail with twrp and Odin
My conclusion is that the memory is defective but you won't know for sure until you have a cell shop try and force flash the firmware.
geoweb29 said:
Hi, i have a problem with my phone,latest stock rom,no root,i found it stuck on boot screen after i use a non original cable with original charger, is SDS or i can fix it? when i try to use odin with stock rom i get nand write fail everytime ,i see the phone conected in device manager(photo) , in recovery i see red errors and when i enter in download mode odin see the phone but is unable to write, can you help me to fix this or any solution to fix it with usb or sd card only because i dont have profesional tools (box)? thanks
Click to expand...
Click to collapse
if your hard is 16 gig , i am sorry to tell you it is 99% EMMC
I think PC will not solve this problem , you need to flash your phone via box if it fail you need to change EMMC
at last I wish I am wrong
Regards
xcorona said:
if your hard is 16 gig , i am sorry to tell you it is 99% EMMC
I think PC will not solve this problem , you need to flash your phone via box if it fail you need to change EMMC
at last I wish I am wrong
Regards
Click to expand...
Click to collapse
4 months ago before SDS i used emmc brickbug check to scan the phone and the status was Yes,insane chip (photo)
i manage to make a usb jig(photo) and with this i see Factory mode in download mode but same problem with nand write fail, i have to search a new motherboard
may I advise you to look at tutorials in youtube about replacing the mother board it is (solderless job) but it is not easy
you can check them to see the processing of the work , then you can judge by your self if you have the time and the ability to go forward and pick an used phone with smashed screen (choose 32 giga hard)
then you can replace the motherboard
at last I hope all your matters will be fine
Best Regards
I see at this Q&A many people have same problem, My phone just like your now, hope you can fix it, it'll help me alot
I'm still trying to take my phone's storage back, it's 0GB right now .
why does so many note 2 SDS's at this point? mine does it too, it first occured a few weeks back, it was a small issue where some folders wasn't deltable in data, but it was fine i could still use the phone and it functioned normally, untill 4 days ago, i exprienced serious issues, the so corrupted folders in data caused alot of problems, it made the phone randomly freeze, force stops apps, then this day it got more serious than ever, nothing mounts on TWRP, no not even the SD card (SD Card still works tho on my PC) odin nand write failed, i checked a few months ago with the app, it was yes a Insane chip, so i guess its time to say goodbye to my note 2 and move on, it was a great 4 years with this phone, and i am sad to see it go....

[Q][HELP] 16gb debrick image i747?

Let me explain:
First I hard-bricked my 16gb i747 phone by accidentally flashing an old bootloader with twrp, then I debricked it using a debrick image I found online.
One day I left my phone charging over night and I woke up in the morning and found it overheated and soft-bricked again for some reason, at the time I could get into bootloader, but I couldn't flash anything, it kept giving me writing errors and pit write failure. I didn't have time to deal with it at the time so I just picked another phone.
Now --today-- my other phone --Note 3-- got bricked the same way when I tried to install linux on it, but I fixed it using a full 32gb debrick image I prepared before.
I remembered that my old phone -- The i747 -- is still bricked, so I tried to boot it up but this time the phone wasn't booting at all then after listing my usb devices I figured out that it was hard-bricked when It said qulacomm 9008, so I flashed the debrick image I found online and it booted up to bootloader but in a strange way. It says:
Code:
BOOT RECOVERY MODE
CHECK BOOT PARTITIONS.
COPY FROM T-FLASH.
BOOT RECOVERY.
WRITE 159488 sectors.
FLASH WRITE FAILURE
ODIN MODE
PRODUCT NAME: SGH-I747
CURRENT BINARY: Samsung Official
SYSTEM STATUS: Custom
QUALCOMM SECUREBOOT: ENABLE
Warranty Bit: 1
BOOTLOADER AP SWERV: 3
And when I list it, it says 'I9100 (samsung galaxy s II) download mode'.
I tried various pit files for various roms and versions of the device, I tried editing the image before booting up the device, and I tried booting using every possible way, but nothing worked. I've been searching all over the internet for a full debrick image, in hope I could boot from sd card and try to fix it after that, or leave it as it is.
The phone is still overheating at the bottom --around the sdcard slot-- and I'm starting to think that this is a physical damage thing, but I really want to fix this one, please help!
Hope this can help
I personally used these files
It's just my Backup
Search for the files and verify they are what you need
https://mega.nz/#F!o5QQ2AjZ!DkFZP4K7AluKjgeeMFEkIA
Sent from my SM-N950U using Tapatalk
chowming said:
Hope this can help
I personally used these files
It's just my Backup
Search for the files and verify they are what you need
https://mega.nz/#F!o5QQ2AjZ!DkFZP4K7AluKjgeeMFEkIA
Sent from my SM-N950U using Tapatalk
Click to expand...
Click to collapse
Thanks and all, I'm definitely gonna use those files in the future, but...I discovered that my phone was toasted and the problem is with the qualcomm chip, I think that some transistor next to the chip was deformed.

Categories

Resources