CWM is no more there after installing a new rom and new rom won't load. Then i have to flash the stock rom again > root it > install CWM. Again when i install any rom it would install normally but nothing gives a blank screen after reboot and the stock rom is not even there.
The situation is occurring with the following;
Phone: Sony Xperia ARC S (LT18i)
Bootloader: unlocked
Android version 2.3.4 (Build 4.0.2.A.42) -
I have made multiple attempts on installing new roms but nothing works. Every time i reboot after installation im left with a blank screen. Can anyone advise what the problem could be ?
Thanks
Did u flash the kernel for the ROM u flashed ? The ROM will not boot without its kernel.
Sent from my Xperia Arc S using Tapatalk 2
mtpocketz said:
CWM is no more there after installing a new rom and new rom won't load. Then i have to flash the stock rom again > root it > install CWM. Again when i install any rom it would install normally but nothing gives a blank screen after reboot and the stock rom is not even there.
The situation is occurring with the following;
Phone: Sony Xperia ARC S (LT18i)
Bootloader: unlocked
Android version 2.3.4 (Build 4.0.2.A.42) -
I have made multiple attempts on installing new roms but nothing works. Every time i reboot after installation im left with a blank screen. Can anyone advise what the problem could be ?
Thanks
Click to expand...
Click to collapse
you must be installing CWM into the system through one touch command prompt program.. as such as soon as the ROM changes and you wipe out data and cache, CWM disappears..try flashing a custom recovery kernel which are available even for stock roms.
Also follow these steps for a custom ROM (eg CM9):
download the ROM, extracted it into a folder, copy the boot.img where you can remember, then copy the original cm9 ZIP - not the extracted folder- into the root of SD..use fastboot mode of flashtools to flash the kernel boot.img which you had copied..its a recovery kernel so CWM should open..wipe out SD data..then cache..and then go into advanced option and clear dalvik..and then proceed to install zip from sd..then gapps.zip if u want..it should install fine..and then reboot.
Press Thanks if you think i was of help to you..:good:
Thanks
iwarind said:
you must be installing CWM into the system through one touch command prompt program.. as such as soon as the ROM changes and you wipe out data and cache, CWM disappears..try flashing a custom recovery kernel which are available even for stock roms.
Also follow these steps for a custom ROM (eg CM9):
download the ROM, extracted it into a folder, copy the boot.img where you can remember, then copy the original cm9 ZIP - not the extracted folder- into the root of SD..use fastboot mode of flashtools to flash the kernel boot.img which you had copied..its a recovery kernel so CWM should open..wipe out SD data..then cache..and then go into advanced option and clear dalvik..and then proceed to install zip from sd..then gapps.zip if u want..it should install fine..and then reboot.
Press Thanks if you think i was of help to you..:good:
Click to expand...
Click to collapse
Got it - Yes i was installing CWM within stock rom via market. though i tried to install it through adb/windows but still i guess the problem was all about not installing a custom recovery kernel.
Thanks a lot !
Installation aborted error status 7 xperia mini
I succesfully rooted my xperia mini and installed cyanogenmod 9 rc2 (smultron). The device was running fine with no problems then i did a huge mistake i entered in the cwm recovery and i formatted cache data syatem and all that listed there.then i reboot device it stuck on free xperia project logo.then i tried to install rom via cwm i started to give error installation aborted status 7 error. Please help no backup of official rom.
aditya naik said:
I succesfully rooted my xperia mini and installed cyanogenmod 9 rc2 (smultron). The device was running fine with no problems then i did a huge mistake i entered in the cwm recovery and i formatted cache data syatem and all that listed there.then i reboot device it stuck on free xperia project logo.then i tried to install rom via cwm i started to give error installation aborted status 7 error. Please help no backup of official rom.
Click to expand...
Click to collapse
Download stock ROM and install it via Flashtool.
My signature, there is link to download stock ROMs. Search for proper one and install it.
Hi, I want to ask why I can't install DN3 v3 rom by using cwm philz 5.15
It's always show installation aborted or signature verification fail.
I from stock leak 4.3 N7100XXEMI6 without root
Here is my step to install this rom:
1. root through ordin
2. flash philz 5.15 recovery through ordin
3. full wipe including data, cache, dalvi cache
4. Fix permission
5. clear to install new rom
6. flash the DN3 v3 zip
*while installing zip file it always show installation aborted
*But if install other zip file everything go fine just have the problem on flashing custom rom
I was try many way but still get fail. hope some one can help me solve the problem.
updated 4.3official ane now wanna DN3 Rom v3.0
i just updated 4.3 official version :victory: but now i wanna DN3 Rom v3.0 :silly: so how can i flash give me detail for that
and ya do not update official 4.3 they dont give us any note 3 fetures ...:crying:
Issue flashing DN3 rom
Usually for flashing DN3 rom
1. root your device through ordin or stock recovery
2. flash cwm / twrp / phliz recovery
3. full wipe including data, cache, dalvi cache
4. fix permission
5. flash the DN3 rom (might need take some time)
6. Reboot
7. flash note 3 add on apps throught recovery
For my information is like that, but now i stuck on installing DN3 rom zip file while in philz recovery. always get installation aborted.
how to root in 4.3 official knox
yu133 said:
Usually for flashing DN3 rom
1. root your device through ordin or stock recovery
2. flash cwm / twrp / phliz recovery
3. full wipe including data, cache, dalvi cache
4. fix permission
5. flash the DN3 rom (might need take some time)
6. Reboot
7. flash note 3 add on apps throught recovery
For my information is like that, but now i stuck on installing DN3 rom zip file while in philz recovery. always get installation aborted.
Click to expand...
Click to collapse
but how to root ... installed 4.3 official version
patelsagar said:
i just updated 4.3 official version :victory: but now i wanna DN3 Rom v3.0 :silly: so how can i flash give me detail for that
and ya do not update official 4.3 they dont give us any note 3 fetures ...:crying:
Click to expand...
Click to collapse
it is easy to root ur phone just download these
CWM---- http://forum.xda-developers.com/showthread.php?t=1901196 [download the latest one with (.TAR) extension]
samsung usb drivers---google search for them
ODIN from here----http://forum.xda-developers.com/attachment.php?attachmentid=1168421&d=1341114315
now once u have all of the follow this video so that u can get every step
http://www.youtube.com/watch?list=UUA2XWPjQBJVScn7wQjeqMqA&feature=player_embedded&v=NFHZ535L7is
once ur done just update the superSU
thas for rooting need help to install the rom ask me:good:
Installing stopped at Page 1 of the Samsung apps
Hi there ppl,
I need some help.... i deleted everything, so now, my phone is romless.. n when i tried installing ditto note 3 (v3.1), the start up was ok, until u come to a page where u need to choose which apps you want to download.. i jus pressed next and it jus hanged there.. nothing was moving so i off and on my phone, and i tried again.. but yet, still cant install.. can anyone help... im frustrated here... hmmm....
BTW, i'm using the latest version of philz recovery, followed youtube link, and did exactly, but still... cant do much...
kalpeshneo said:
Hi there ppl,
I need some help.... i deleted everything, so now, my phone is romless.. n when i tried installing ditto note 3 (v3.1), the start up was ok, until u come to a page where u need to choose which apps you want to download.. i jus pressed next and it jus hanged there.. nothing was moving so i off and on my phone, and i tried again.. but yet, still cant install.. can anyone help... im frustrated here... hmmm....
BTW, i'm using the latest version of philz recovery, followed youtube link, and did exactly, but still... cant do much...
Click to expand...
Click to collapse
Just using previous philz touch recovery (Philz 5) and everything will works fine.
Using latest philz 6 will cause eror and hang (it happen to me too and it take a half day too realize the problem in the philz not the Rom )
yu133 said:
Hi, I want to ask why I can't install DN3 v3 rom by using cwm philz 5.15
It's always show installation aborted or signature verification fail.
I from stock leak 4.3 N7100XXEMI6 without root
Here is my step to install this rom:
1. root through ordin
2. flash philz 5.15 recovery through ordin
3. full wipe including data, cache, dalvi cache
4. Fix permission
5. clear to install new rom
6. flash the DN3 v3 zip
*while installing zip file it always show installation aborted
*But if install other zip file everything go fine just have the problem on flashing custom rom
I was try many way but still get fail. hope some one can help me solve the problem.
Click to expand...
Click to collapse
It sounds that you have a damaged file. Download the DN3 v3.1 ROM once it's complete verify its integrity using any MD5 checker tool.
kalpeshneo said:
Hi there ppl,
I need some help.... i deleted everything, so now, my phone is romless.. n when i tried installing ditto note 3 (v3.1), the start up was ok, until u come to a page where u need to choose which apps you want to download.. i jus pressed next and it jus hanged there.. nothing was moving so i off and on my phone, and i tried again.. but yet, still cant install.. can anyone help... im frustrated here... hmmm....
BTW, i'm using the latest version of philz recovery, followed youtube link, and did exactly, but still... cant do much...
Click to expand...
Click to collapse
Use Philz version 5.15, and clean all the data using Philz recovery. Do not select the option "Wipe Data" in the DN3 installer, this may cause your installation process to hang.
dvn2008 said:
It sounds that you have a damaged file. Download the DN3 v3.1 ROM once it's complete verify its integrity using any MD5 checker tool.
Use Philz version 5.15, and clean all the data using Philz recovery. Do not select the option "Wipe Data" in the DN3 installer, this may cause your installation process to hang.
Click to expand...
Click to collapse
Thanks guys for the help.. will download the philz 5.15 then and do it. anyways, ru guys having any problems with the ditto rom? does it hand when u multitask, etc?? coz i heard fr my frens that it hangs often...
appreciate your feedback guys. Thanks
ijsiregar said:
Just using previous philz touch recovery (Philz 5) and everything will works fine.
Using latest philz 6 will cause eror and hang (it happen to me too and it take a half day too realize the problem in the philz not the Rom )
Click to expand...
Click to collapse
I just signed up to say THANKYOU.... install Touchphilz 5!! it works than especially when you install DN3 v.3.1 or above!! thanks again!
Ditto Note 3 -> 3.2
DN3 rom work perfectly for me so far starting from v3 and now in v3.2.
I flashed DN3 rom in following sequence:-
(i) I came from MK4 Wanamlite previously and then I flash TWRP v2.6.0.3 via Odin
(ii) then I flashed MJ5 bootloader (downloaded from JoelDroid rom site) before installing DN3 rom
(iii)then I flashed DN3 v3 successfully.
With the DN3 v3.2 update, I tried dirty flash without wipe but hell lots of problems so finally I did full wipe, format data and then
clean install DN3 v3.2 anf all working perfectly so far including all the Note 3 features.
problem
hi
after i install dn3 ROM i can't make a call the imei is good but not registered to network
please help me
i got the same problem on 7105 Imei but no network, and stuck in factory mode, changing to on and running terminal script didnt help
i just updated 4.4.2 KK official version note 2 but now i wanna DN3 Rom without root..can i use DN3 rom feuture in my phn..
ota 3.2.1
Hi
I have one problem with OTA uppdate
I can't uppdate to 3.2.1
When I push uppdate , displays an error message
What is a problem?
yu133 said:
Usually for flashing DN3 rom
1. root your device through ordin or stock recovery
2. flash cwm / twrp / phliz recovery
3. full wipe including data, cache, dalvi cache
4. fix permission
5. flash the DN3 rom (might need take some time)
6. Reboot
7. flash note 3 add on apps throught recovery
For my information is like that, but now i stuck on installing DN3 rom zip file while in philz recovery. always get installation aborted.
Click to expand...
Click to collapse
Download the zip again and copy it on your sd card(maybe not copied well). This happens to me too
[email protected]
i installed cwm recovery 6.0.3.0 and i also installed cm-9
but it show while booting only th LG Logo. whats wrong with the phone?
any ideas to get a rom working?
and usb mount in recovery is also not working.
is there a possability to get everything working again?
Can you please mention the link of the rom which flashed...
PS.Before installing the rom did you format/wipe " /system "
Same problem here
theprakhar said:
Can you please mention the link of the rom which flashed...
PS.Before installing the rom did you format/wipe " /system "
Click to expand...
Click to collapse
I flashed this ROM MiniCM10-4.0.2-20121207-UNOFFICIAL-ALPHA2-p350
and yes i wiped sytem cache
I followed the instruction from this website
ninjaromeo.com
update-lg-optimus-me-p350-jelly-bean-cm10
How to flash MIUI Global stable ROM in Xiaomi Redmi 1s. I am currently on Nougat based ROM.
I tried fastboot method by flash tool but no luck.
Also tried flashing recovery file by TWRP again not worked.
Please help me to flash MIUI
I thing MIUI recovery and unroot is needed
saurabhrakshak said:
How to flash MIUI Global stable ROM in Xiaomi Redmi 1s. I am currently on Nougat based ROM.
I tried fastboot method by flash tool but no luck.
Also tried flashing recovery file by TWRP again not worked.
Please help me to flash MIUI
I thing MIUI recovery and unroot is needed
Click to expand...
Click to collapse
Just go to twrp wipe all thing ( systm ,data ,cache,dalvik ) then reboot recvry
Then install miui 8.2 or any build and then reboot thts its it will take long time to instal dnt panic
vjadhikari said:
Just go to twrp wipe all thing ( systm ,data ,cache,dalvik ) then reboot recvry
Then install miui 8.2 or any build and then reboot thts its it will take long time to instal dnt panic
Click to expand...
Click to collapse
I did this but error occurred
Which file I have to flash??
I tried recovery zip but due to less system space falshing error occured
clean flash MIUI ROM
error will appear
clear dalvik-cache
flash the rom again
EmanzzKie said:
clean flash MIUI ROM
error will appear
clear dalvik-cache
flash the rom again
Click to expand...
Click to collapse
Can you tell me step by step procedure
Which file should download..Can I flash the zip using TWRP ?
saurabhrakshak said:
Can you tell me step by step procedure
Which file should download..Can I flash the zip using TWRP ?
Click to expand...
Click to collapse
Follow this exactly. This works for me, but right now Im not using stock rom.
Requirements:
Latest version of twrp 3.0.2-1;
If you can't flash the rom switch to twrp version 3.0.2
A backup of files
1. Download latest MIUI Rom for Redmi 1s
(You can get it on google)
2. Put Rom into your sd card
3. Reboot to recovery
4. Wipe>Advanced Wipe
- Dalvik cache
- cache
-system
-data
-internal storage (backup your files)
5. Swipe to wipe
6. Flash rom via Install>select storage > sd card > (find your rom)
7. Either flashing will be successful or not
If not then error will appear, then wipe dalvik cache
8. Flash the rom again
-it should work (requirement applies)
Changing recoveries might help (dunno why)
Try switching to philz touch
Then clean flash rom
saurabhrakshak said:
I did this but error occurred
Which file I have to flash??
I tried recovery zip but due to less system space falshing error occured
Click to expand...
Click to collapse
Did u rebooted recvry aftr wiping all ?
And if error occured again flash it . it will be flashd i am sure .
vjadhikari said:
Did u rebooted recvry aftr wiping all ?
And if error occured again flash it . it will be flashd i am sure .
Click to expand...
Click to collapse
EmanzzKie said:
Follow this exactly. This works for me, but right now Im not using stock rom.
Requirements:
Latest version of twrp 3.0.2-1;
If you can't flash the rom switch to twrp version 3.0.2
A backup of files
1. Download latest MIUI Rom for Redmi 1s
(You can get it on google)
2. Put Rom into your sd card
3. Reboot to recovery
4. Wipe>Advanced Wipe
- Dalvik cache
- cache
-system
-data
-internal storage (backup your files)
5. Swipe to wipe
6. Flash rom via Install>select storage > sd card > (find your rom)
7. Either flashing will be successful or not
If not then error will appear, then wipe dalvik cache
8. Flash the rom again
-it should work (requirement applies)
Changing recoveries might help (dunno why)
Try switching to philz touch
Then clean flash rom
Click to expand...
Click to collapse
Gonna try.. I let you know
Thanks in advance :good:
saurabhrakshak said:
Gonna try.. I let you know
Thanks in advance :good:
Click to expand...
Click to collapse
YES WORKED..
clear all then flash first time got error
again clear all catch internal external reboot to recovery
then flashed
Successed :good:
saurabhrakshak said:
YES WORKED..
clear all then flash first time got error
again clear all catch internal external reboot to recovery
then flashed
Successed :good:
Click to expand...
Click to collapse
Yeppp
How to install native root, miui v.8.2.1.0
zam09 said:
How to install native root, miui v.8.2.1.0
Click to expand...
Click to collapse
Fastboot twrp as redmi 1s doesn't have boot loader locked next flash SuperSU zip
hey there.
i just unlocked my bootloader and rooted my phone.
i installed twrp and the latest version of viper roms for htc 10.i was using this rom until i saw some bugs.
after that i cannot install any rom to my phone.i wanna switch back to STOCK rom and now TWRP just allows me to flash vipers rom!
i can just install viper roms.
when im trying to flash stock roms or any others,the twrp shows me:
Invalid ZIP file Format!
Error installing ZIP file
Click to expand...
Click to collapse
i tried factory reset or OTA Upates too but same resualt.
plz help me to flash the stock rom
my cid is : htc_j15
Get the latest Firmware RUU.... Flash that and you should be able to flash any ROM. Make sure it has ALL of the firmware updates for your phone.
The errors you are getting are indicative of a Bad downloaded ROM or a corrupt ROM file.
Oh and when you install a new ROM wipe Dalvic Cache, Cache, System and Data.....
Don't forget to hit thanks!!