Important Notice:
The original poster and creator of this thread is JustSueMe. His original work was one of the main contributors for me to work on this topic.
As proof of the above, his original message is kept in this main post, just below - and the people thanking this thread are there due to his efforts.
Along with JustSueMe's work, I would also like to refer Simon Van der Veldt for his work on this topic as well - particularly on Github, the porters at #[email protected], especially mal- for his patience and support helping me out with this and the users here like Alecsandru also trying to making this work.
So a Big Thank You to all!
2016-07-07 Update:
Haven't had a lot of time lately to work on this, but still some new information on current status:
* The mer wiki page below now includes the notes I used on my port, by addressing each chapter of the SailfishOS HADK Porting Guide - so for those willing to work on this, go have a look and let me know how it goes!
* About the outgoing call issue: this seems to be a more delicate matter than initially thought. There isn't much information available out there, but based on JustSueMe's early work found here and also chatting with some very knowledgeable people down at #sailfishos-porters, it seems that we're dealing with an old RIL (radio interface layer) which is closed source and may have some issues in itself, and at this point, if assuming that if by working on cm-12.1 stable, then it should also work on SOFS, then perhaps something can be done either at ofono/audio routing level - relevant reading here about the architecture
* WLAN hotspot: this is not working on v0.0.9 and may be made to work perhaps on 0.0.10, will have to look a it
* Cameras: still no progress worth mentioning
2016-06-20 Update:
Mer Wiki Page
Latest SailfishOS Release
Youtube Video Gallery
2016-06-18 - version 0.0.8 - based on cyanogenmod 12.1 / android 5.0.1
2016-06-26 - version 0.0.9 - Bluetooth: now working, but with quirks. Details in the Release Notes
Things that don't work
Jolla Store (Harbour) doesn't work. Do not sign in with Jolla account.
Bluetooth: yet to be set up.
Voicecall: receiving calls works properly (along with Speaker, Pad and Mic buttons) / making calls fails with 3 tone signal.
Camera: only front camera photo works. back camera photo + any camera video fails.
Mobile Internet: intermittent feature, between reboots:
setting PIN code for the SIM card seems to help;
additionally, try giving it 10-15sec pause once the SIM inserted screen shows up, and then enter the PIN to unlock.
Home key not working.
Headphone jack.
Screen going to suspend mode not working.
Things that work
Sensors
GPS
SMS
Audio
Original Post from JustSueMe below:
Only You Are Responsible For Your Device. Dont Do Anything If You Dont Understand
Code:
[SIZE="2"]
88 ad88888ba 88b d88
88 ,d d8" "8b 888b d888
88 88 Y8, 88`8b d8'88
88 88 88 ,adPPYba, MM88MMM `Y8aaaaa, 88 88 ,adPPYba, 88 `8b d8' 88 ,adPPYba,
88 88 88 I8[ "" 88 `"""""8b, 88 88 a8P_____88 88 `8b d8' 88 a8P_____88
88 88 88 `"Y8ba, 88 `8b 88 88 8PP""""""" 88 `8b d8' 88 8PP"""""""
88, ,d88 "8a, ,a88 aa ]8I 88, Y8a a8P "8a, ,a88 "8b, ,aa 88 `888' 88 "8b, ,aa
"Y8888P" `"YbbdP'Y8 `"YbbdP"' "Y888 "Y88888P" `"YbbdP'Y8 `"Ybbd8"' 88 `8' 88 `"Ybbd8"'
[/SIZE]
This is Sailfish OS for I9505 only
only tested on int version.
Instructions:
Full wipe is needed.
Flash the relavent parts :
--
CM can be obtained from: CM-website
Hybris can be downloaded from here : Dropbox
--
Onces rebooted you will be presented with ONLY the samsung galaxy boot screen
Plug in a usb cable and login via telnet on port 23
--commands will show via telnets welcome screen
so move the file for enabling root and run the echo 'continue' command stated.
now login to telnet via port 2323
congrats you are now logged into SailfishOS and can do some debugging/modifications.
--
BUT ITS NOT USEABLE AS DAILY !!!?
Not to worry ! You have two options:
1. Ignore this thread, this rom isnt for you
2. or you can Dual boot:
---
Dual Booting:
I have made 2 .zips to enable easy dual boot via Custopm recovery
so place these .zips on your sdcard and flash one everytime u want to switch OS.
Boot back into Android (CM) - Dropbox
Book back into SailfishOS - Dropbox
----
Current problems:
Lib Error
Code:
.~))>>
.~)>>
.~))))>>>
.~))>> ___
.~))>>)))>> .-~))>>
.~)))))>> .-~))>>)>
.~)))>>))))>> .-~)>>)>
) .~))>>))))>> .-~)))))>>)>
( )@@*) //)>)))))) .-~))))>>)>
)[email protected](@@ //))>>))) .-~))>>)))))>>)>
(( @[email protected]). //))))) .-~)>>)))))>>)>
)) )@@*[email protected]@ ) //)>))) //))))))>>))))>>)>
(( ((@@@[email protected]@ |/))))) //)))))>>)))>>)>
)) @@*. )@@ ) (_(-b |))>)) //)))>>)))))))>>)>
(( @@@([email protected](@ . _/`-` ~|b |>))) //)>>)))))))>>)>
)* @@@ )@* (@) (@) /b|))) //))))))>>))))>>
(( @. )@( @ . _/ / / b)) //))>>)))))>>>_._
)@@ (@@*)@@. (6///6)- / ^ b)//))))))>>)))>> ~~-.
( @[email protected]@. @@@.*@_ VvvvvV// ^ b/)>>))))>> _. `bb
((@@ @@@*.(@@ . - | o |' ( ^ b)))>> .' b`,
((@@).*@@ )@ ) ^^^/ (( ^ ~)_ / b `,
(@@. (@@ ). `-' ((( ^ ` | b `
(*[email protected]* / (((( | | | . b `.
/ / ((((( / _.-~ Y, b ;
/ / / (((((( .-~ _.`" _.-~`, b ;
/ / `(((((() ) (((((~ `, b ;
_/ _/ `"""/ /' ; b ;
_.-~_.-~ / /' _.'~bb _.'
((((~~ / /' _.'~bb.--~
(((( __.-~bb.-~
.' b .~~
:bb ,'
~~~~
Updates:
XDA:DevDB Information
i9505- Sailfish OS, ROM for the Samsung Galaxy S 4
Contributors
JustSueMe
ROM OS Version: 4.4.x KitKat
Based On: CM, Hybris
Version Information
Status: Alpha
Created 2014-09-27
Last Updated 2014-09-27
R
R.
Nice! Although I'm no hero with adb and commands, I do like to see a new ROM in the i9505 forum!
Me Gusta!
this is so great
how is it performing ? can you use playstore on that os? or install any apk? does root and f2fs work?
thx
Thank you - subscribed and watching with interest
Screenshots plz?
I Think you guys have the wrong idea about this ROM as is.
we have no gui so its debug / developers only at this point
JustSueMe said:
we have no gui so its debug / developers only at this point
Click to expand...
Click to collapse
Nope, I understand totally, like I said, watching with interest what happens to this. Thank you for your work @JustSueMe :highfive:
Very nice! I'll give it a shot as soon as I have the time.
finally
No more news?
santya95 said:
No more news?
Click to expand...
Click to collapse
Just the lib errors, cant find libs but as far as I can see the strings are there and files exist. :/ just a little bump on the road
Sent from my GT-I9505 using XDA Free mobile app
subscribed
Bump. Is there any hope left?
zAo_ said:
Bump. Is there any hope left?
Click to expand...
Click to collapse
Dead like bread.
Nah just kidding.
i was waiting for this OS also to come up lol still waiting.:highfive:
xDroidZz said:
Dead like bread.
Nah just kidding.
i was waiting for this OS also to come up lol still waiting.:highfive:
Click to expand...
Click to collapse
I will confirm that it is dead... well as far as this thread goes. Unfortunately, part of my s4 died, so even tho it will boot any rom, daily use features can't be tested anyway, :banghead: , my next phone will be the new Ubuntu device as off late this month
JustSueMe said:
I will confirm that it is dead... well as far as this thread goes. Unfortunately, part of my s4 died, so even tho it will boot any rom, daily use features can't be tested anyway, :banghead: , my next phone will be the new Ubuntu device as off late this month
Click to expand...
Click to collapse
How did your s4 died? Dropped it or bricked it by software?
Sent from my GT-I9505 using XDA Free mobile app
xDroidZz said:
How did your s4 died? Dropped it or bricked it by software?
Sent from my GT-I9505 using XDA Free mobile app
Click to expand...
Click to collapse
well its not dead but everyday functions don't work, video. audio/calls. camera.
Camera did one of them auto firmware updates and I can no longer access these functions. I've tried every suggestion to fix it nothing is working.
Sent from my MB860 using XDA Free mobile app
JustSueMe said:
well its not dead but everyday functions don't work, video. audio/calls. camera.
Camera did one of them auto firmware updates and I can no longer access these functions. I've tried every suggestion to fix it nothing is working.
Sent from my MB860 using XDA Free mobile app
Click to expand...
Click to collapse
wow and you are stuck with a Motorola ATRIX 4G MB860 ? Bad luck mate ! Thanks for the contribution that you made :good:
Related
Known bug list and known work arounds are in Post 2, at the bottom, below the instructions. Please if you read nothing else, read post 2, and report anything NOT already listed there, thank you.
WeeFeeri was kind enough to take the time to make a video showcasing these CM9 nightlies (featuring Build 46) so check it out HERE! Please be sure to give him your thanks for the taking the time to do this on his own!
As per notsointeresting's suggestion, and a few complaints of dev-host's reliability lately, I setup androidfilehost to hold my stuff, I'll be slowly migrating everything over for use as a mirror.
I'm writing a general guide for the A100, please give it a read if you have any questions. Its a WIP, but is full of goodness, I promise! Guide to all things A100
Since there doesn't seem to be any nightly releases for A100 CM9, I decided to build them myself for myself, then figured, hey, if I build them, why not let others have at them? And with that I present to you....
CM9 Nightlies by pio_masaki
What is a nightly vs whatever release?
Nightlies are untested and considered unstable, however they contain all of the latest source code available. This means things may be fixed, things remain broken, or new things are broken. It also may mean its your new favorite daily driver rom.
What do you do to this rom?
Nothing at all. I only compile after syncing to the repo daily. This is not modified by me in any way, shape or form, completely stock vanilla CyanogenMod roms.
How often will you release these?
Whenever possible I plan to release these nightly, or once a day. I'm sorry if I miss a day or two, I will build and upload when I have the time. I do NOT have time to test each one, so that will have to be a risk you take. This first build boots and runs, I do not know of any bugs or what works or not.
What about bugs?
I don't know, please tell me in the thread and I will add what is broken or fixed to the post. Posted at the bottom of post 2 for now with work a rounds if known, dated with build number reported.
What does the filename mean?
the file names will be in this format: cm-9-6-11-B1-a100-PM.zip
here's the breakdown:
cm-9 is of course, its a CM9 release.
6-11 is the date of the build.
B1 is the build number, tomorrow will be B2, so on. If there is a B1-2 that's a second build for the same day. Not likely, but just in case.
a100 device model this is meant for, please don't use this on another device.
PM is pio_masaki.
Source
Source is directly synced from CM, nothing is added by me. Kernel is directly from ezterry, in his original zip file release, nothing added by me.
Thanks
Thanks to the CM team for doing awesome work to get this kind of stuff to most devices possible!
EzTerry for making an OC kernel for our devices!
da-pharoah for letting me bounce ideas off him and letting me work things out through him and cheering me on for this.
x0hell0x for inspiring me to decide to attempt compiling from source.
Downloads
Theme:
EpicBlueCM9 Theme courtesy of stetsonaw! Be sure to give him your thanks!
Add ons:
ezterry's OC kernel Thread, Please read it all!
Required for Play Store and other Google stuff/framework:
gapps
Optional scripts for wiping:
Blackhole Wipe/Nullifier Thread
Experimental CWM Touch Recovery:
This is an experimental build! Use caution with this!
Removed as it seems pretty broken.
If it works out OK for anyone willing to try it out, I'll do a formal release for it later.
Builds:
Build 6 6-16-12
Build 7 6-17-12
Build 8 6-18-12
Build 9 6-19-12
Build 10 6-20-12
Build 11 6-21-12
Build 12 6-22-12
Build 13 6-23-12 *experimental* (new build machine) Has issues lol skip it.
Build 14 6-24-12
Build 15 6-25-12
Build 15 Experimental
Build 16-2 6-26-12 *see note below Update section*
Build 17 6-27-12
Build 18 6-28-12
Build 19 6-29-12
Build 20 6-30-12 We made it! 20 straight!
Build 21 7-1-12
Build 22 7-2-12
Build 23 7-3-12
Build 24 7-4-12
Build 25 7-5-12
Build 26-4 7-6-12 Had multiple build fails, sorry it's so late.
Build 27 7-7-12
Build 28 7-8-12
Build 29 7-9-12
Build 30 7-10-12 | Mirror
Build 31 7-11-12 | Mirror
Build 32 7-12-12 | Mirror
Build 33 7-13-12 | Mirror
Build 34 7-14-12 | Mirror
Build 35 7-15-12 | Mirror
Build 36 7-16-12 | Mirror
Build 37 7-17-12 | Mirror
Build 38 7-18-12 | Mirror
Build 39 7-19-12 | Mirror
Build 40 7-20-12 | Mirror
Build 41 7-21-12 | Mirror
Build 42 7-22-12 | Mirror
Build 43 7-23-12 | Mirror
Build 44 7-24-12 | Mirror
Build 45 7-25-12 | Mirror
Build 46 7-29-12 | Mirror
Build 47 7-30-12 | Mirror
Build 48 7-31-12 | Mirror
Build 49 8-1-12 | Mirror
Build 50 8-2-12 | Mirror
Build 51 8-3-12 | Mirror
Build 52 8-4-12 | Mirror
Build 53 8-5-12 | Mirror
Build 54 8-6-12 | Mirror Note - the file names are wrong, I was to lazy to reupload them, this is the correct info, ignore the file name.
Build 54 8-7-12 | Mirror
Build 55 8-8-12 | Mirror
Build 56 8-9-12 | Mirror
Build 57 8-10-12 | Mirror
Build 58 8-11-12 | Mirror
Build 59 8-12-12 | Mirror
B60 8-13-12 | Mirror
Build 61+ are now on Goo.im and can be accessed through the goo.im app. Even will tell you when the new nightly is available for you! For now I'll just be updating the thread Build number and date, I won't be linking anymore.
Build Notes
Build 16 is a sort of mile marker, rotation lock fix got merged today! I had already synced and built Build 16, however (and I announced it over twitter for those that care) scrapped it in favor of adding the newly merged Rotation Lock fix! Luckily I was sitting around in #Iconia-dev when it was announced. So, please test rotation lock and report back if its working or not for you guys!
Instructions
Fresh install from another rom:
Download to your external SD card
Reboot into recovery
Backup current installation
Wipe data, system, cache, dalvik cache (optional use my Blackhole scripts)
Install from zip, pick the CM9 zip
Flash gapps
Once done, wipe cache and dalvik cache again
Reboot system
Wait 10 minutes, then reboot system
Log into google and setup your device
Enjoy
Updates from my previous builds:
Backup current installation
Flash the new build zip
Clear cache
Clear dalvik
Reboot
Let settle 10 minutes
Reboot
Enjoy.
Only for updating over a previous PM CM9, not meant for flashing over any other rom, even another CM9.
Advanced update method:
Backup your current PM CM9 install you wish to update
(CWM) Go to mounts, mount /system, then go down to format /system
(CWM) wipe data
(TWRP) Go to wipe, wipe system and data
Install newer PM CM9 version
Install gapps
Go to restore, advanced restore
Restore ONLY Data
Clear cache and dalvik, fix permissions
Reboot system
Let settle 10 minutes
Enjoy
This method will clear the system partition and replace with the new system, but restores your user data, settings, apps, etc. Its IMO a cleaner upgrade method then "Dirty Flashing" straight over the previous rom. Intended ONLY for updates from a previous PC CM9, no other roms.
Current known Bugs
6-11-12, B1: You have to disable the screen off animation or your device will reset everytime you press the power button. Settings>Display> Uncheck Screen-off animation prevents it.
6-12-12, B1: Labros1995 reports rotation lock still broken.
6-16-12, NA: HDMI audio still not working, reported by pomka78
6-19-12, B7: labros1995 reports Torch Toggle does not work, volume is upside down in portrait mode (still uses landscape default layout).
6-29-12, NA: Its not really a bug, but it has come up, themes DO work, however complex themes will give a compiled error. For now, only simple color changing themes work, such as the Holo series of themes. I don't think its the ROMs fault, I think it has to do with the themes not being for Tablets. But, I added it here anyways, as a heads up.
7-1-12, B20: nickownzya reported Chrome crashes going into settings, confirmed by mapaz04. Turns out its the newest version, 18.0.1025.166 (Official Build 130050), confirmed by mapaz04. Chrome version 18.0.1025.133 does not appear to have this issue. The only fix for now, if possible, is to uninstall the update. Not possible on a freshly downloaded restore, but maybe through TiBu or whatever backup app you use. Chrome appears to otherwise function fine, just can't enter settings.
Updates:
6-13: Modified the OPs a little bit, added advanced update instructions in post 2. Added bug list location to post 1.
6-25: Added CWM Touch experimental to downloads, added some whatever info. I dare you to find it!
7-2: I've put my A100 up for sale today, but I will continue building these nightlies until the official nightlies begin rolling out, as promised.
7-2: Added a new link to the downloads section of post 1, EpicBlueCM9 theme by stetsonaw, which he confirms working for our devices!
7-4: Removed builds 1-5 as I'm sure they are no longer needed, and they were using dropbox anyways. All builds now on Dev-Host.
7-4: As the new title states, I've been working on my custom edition CM9, some build.prop tweaks, some init.d tweaks, some free apps that I generally use. It was originally going to be a pre built restore for myself, but I figured, as always, why not share it? Should be available in it's alpha form tonight or tomorrow. Still a LONG way to go on it!
7-6: The custom edition is going a little slower then I expected, hitting a couple of road blocks with the modular expansion I had in mind for running scripts, but it's getting there. cdkg has offered to test run today's alpha, so hopefully that goes well. I can't test stability since I'm constantly flashing new crap to the build, or entire new builds, that I never spend more then an hour on any flash lol. It's coming, eventually. If cdkg doesn't run into any issues I'll put up the alpha 1 build.
7-8: For those that haven't noticed, and the few still that read this section, (does anyone read here?) the custom edition is availble in the Dev section as of this morning, Aoikaze Alpha 3, please give it a whirl and report any issues you may run into, if any (because I'm perfect and all).
7-9-12: As per notsointeresting's suggestion, and a few complaints of dev-host's reliability lately, I setup androidfilehost to hold my stuff, I'll be slowly migrating everything over, then using dev-host as a mirror.
7-25-12: I'm taking a short vacation, I leave the morning of 7-26 and I'll return 7-29, I know it's a short trip, but I think I need a break for a few days. I will likely not have any kind of data up there, so I can't remote the machine to build from there, so there will be NO builds until 7-29. I also probably will fall way behind on the forums as I probably can't check in on them either, so help each other out as best you can! I wanna see peace, love and CM15 when I get back!
8-11-12: General project update. Considering my A100 bricked, I get complaints constantly about slow downloads, missing days, missing features, random broken crap that I said would happen, and other general BS that I keep getting about these builds, I'm considering stopping. I did this as a favor for everyone, it's not my job, it's not required that I do this every single day, and I DON'T GET PAID FOR THIS. So either deal with the slow hosting (it's free, want faster? It costs money) and the random broken things and odd bugs, or please stop messaging me complaining about it or I just won't build these at all, and when CM10 comes up for nightlies, I won't build them either. I'll just do my own thing, build them for myself, and laugh at people with 4 month old CM10 releases (hint, I built a CM10 an hour ago, yes I can build A100 CM10s). All this complaining REALLY makes me wonder why I'm even doing this, spending my time and money on this stuff, when it doesn't seem like it really even matters. It kinda ruins the reason I started doing this and kills my drive to even do anything for android any more, let alone the a100 or the a200. /rant
8-13/14-12 : A final general project update - I'm stopping these for awhile. You may have noticed this message already below the latest download. I'm not going to name names, just know I'm tired of the complaints and demands, if you want to demand I do something, then make it worth my while, until then deal with what I can give you when I can give it. If you aren't happy with my builds, build it yourself.
Thanks for making this available!
CM9 Nightly builds for our A100, it's a beautiful thing.
PM me if the is anything I can do to help
Sent from my A100
All I ask is that if you notice any bugs to post them up so I can add them to the post, as well any anything that used to be broken but now works, hopefully the CM team can take notice and work fixes for our device branch.
Great job man. I will definitely flash this tomorrow and report back with my experience. I love that we have options now!
tested the rom!it works fine! rotation lock not working only..
labros1995 said:
tested the rom!it works fine! rotation lock not working only..
Click to expand...
Click to collapse
Nice thanks for the report I'll add it in. I think that fix is awaiting approval for merging so hopefully that will get fixed soon.
Tapatalked from my Galaxy S II.
Does this have adhoc wifi support or can it be added? I tether my tablet to my nokia phone a lot.
Sent from my A100 using xda premium
plaseo said:
Does this have adhoc wifi support or can it be added? I tether my tablet to my nokia phone a lot.
Sent from my A100 using xda premium
Click to expand...
Click to collapse
Pretty sure all AOSP roms support ad hoc wifi. Tethers to my galaxy s 2 with AOKP fine. AOSP doesn't have the same limitations as Acer roms as they share all android code with pretty much every other device in existence.
Edit: also I'm not a dev, I can't add things to these releases, I'm just syncing the code and making the rom, then putting it online for whoever wants it. That alone takes like 4 hours.
Tapatalked from my Galaxy S II.
Fantastic!! Tomorrow I'll try, anyone reports bugs?
Inviato dal mio A100 usando Tapatalk
Any reported or known bugs are listed in the second post, below the instructions for anyone to see, in case anyone missed my adding it there.
Side note, Build 2 will be available shortly. It seems to only take a couple of hours now instead of 4 like yesterday.
So we can't just upgrade whenever a newer rom is posted? We have to wipe n reflash every time, or can we just wipe dalvik n cache, then flash to update?
Sent from my A100 using Tapatalk 2
MDMonster said:
So we can't just upgrade whenever a newer rom is posted? We have to wipe n reflash every time, or can we just wipe dalvik n cache, then flash to update?
Sent from my A100 using Tapatalk 2
Click to expand...
Click to collapse
Well you can dirty flash the same rom over each other. And yes clear cache and dalvik after flashing. The instructions are for fresh installs from another rom. Keep in mind this may prevent fixed bugs from being fixed on your install but if anything broken shows up fixed I'll post it.
Tapatalked from my Galaxy S II.
pio_masaki said:
Well you can dirty flash the same rom over each other. And yes clear cache and dalvik after flashing. The instructions are for fresh installs from another rom. Keep in mind this may prevent fixed bugs from being fixed on your install but if anything broken shows up fixed I'll post it.
Tapatalked from my Galaxy S II.
Click to expand...
Click to collapse
K, thx :-D
Sent from my A100 using Tapatalk 2
MDMonster said:
K, thx :-D
Sent from my A100 using Tapatalk 2
Click to expand...
Click to collapse
No problem. I'll add those to the first post with the install instructions too.
Tapatalked from my Galaxy S II.
pio_masaki said:
No problem. I'll add those to the first post with the install instructions too.
Tapatalked from my Galaxy S II.
Click to expand...
Click to collapse
Awesome :-D . I knew about it with my captivate, but like no one ever mentions that with any Iconia ROMS, so I thought it was different with them. Thx for clearing that up for me
Sent from my A100 using Tapatalk 2
This looks awesome, will be spending some time with this tomorrow, will post whatever tweaks etc work and dare useful
Loving the latest cm9 on my touch pad to have it here too is real nice
Sent from my A100 using xda premium
Awesome! Thanks pio! Testing this now. I noticed there is no Power Control widget. Is there a way to get the AcerRing on this one?
Sent from my A100 using xda premium
[email protected] said:
Awesome! Thanks pio! Testing this now. I noticed there is no Power Control widget. Is there a way to get the AcerRing on this one?
Sent from my A100 using xda premium
Click to expand...
Click to collapse
Not sure what you mean by power control widget, but you can add toggles to the clock pop up and scroll down. I have my wifi bt gps and brightness there.
Acer ring will only be available if one of the devs decides to port it to CM9 as there's changes to be made in the framework to get it working. Just pushing the apk won't work.
Tapatalked from my Galaxy S II.
pio_masaki said:
Not sure what you mean by power control widget, but you can add toggles to the clock pop up and scroll down. I have my wifi bt gps and brightness there.
Acer ring will only be available if one of the devs decides to port it to CM9 as there's changes to be made in the framework to get it working. Just pushing the apk won't work.
Tapatalked from my Galaxy S II.
Click to expand...
Click to collapse
Yeah, the toggle widget but I can use Widgetsoid or the toggles in the notification pop up.
Lol that's what I did, flashed the AcerRing zip to push the apk. Of course that didn't work.
So far so good.
Sent from my A100 using xda premium
For the latest official build, visit http://dl.omnirom.org/maguro/,
latest unified and device specific builds can be found here (security updates, latest OMAP4 improvements)..
TWRP with hardware decryption support can be found here
Google Apps can be found at http://opengapps.org/?api=6.0&variant=nano - beware that if you choose OpenGApps, only the nano version will fit! Also, starting from M, it's recommended to install gapps before the initial boot so the permissions are properly set up.
Bugs:
- Sometimes, quiet speaker pop sounds can be heard at the beginning and/or end of some audio streams (ie. touch sounds - the workaround is to disable them). For some reason, this isn't affecting everyone.
FAQ:
Does this ROM has CMA?
- Yes!
Does this ROM supports F2FS?
- Yes, on /data.
Does this ROM uses DDK 1.9?
- Yes, with all the camera issues (ie. pink lines, rare crashes) resolved.
Why does the initial boot take so long, and where are my live wallpapers?!
- To make room on the system partition for the (bigger) M gapps packages, I had to sacrifice dexpreopt and the live wallpapers. This can result in pretty long initial boots or upgrade boots, and dexpreopt might run during the first time setup wizard as well, slowing down the system for an additional couple minutes.
Want to support development? Consider donating, I spent countless of hours with this device
XDA:DevDB Information
OmniROM, ROM for the Samsung Galaxy Nexus
Contributors
Ziyan, MWisBest, Android-Andi
Source Code: https://github.com/omnirom
ROM OS Version: 6.0.x Marshmallow
ROM Kernel: Linux 3.0.x
Based On: OmniROM
Version Information
Status: Nightly
Created 2016-04-17
Last Updated 2017-08-18
Ziyan said:
For the latest build, check the downloads section (above this post).
Google Apps can be found at http://opengapps.org/?api=6.0&variant=nano - beware that if you choose OpenGApps, only the nano version will fit! Also, starting from M, it's recommended to install gapps before the initial boot so the permissions are properly set up.
Bugs:
- Sometimes, quiet speaker pop sounds can be heard at the beginning and/or end of some audio streams (ie. touch sounds - the workaround is to disable them). For some reason, this isn't affecting everyone.
- Report back anything else you find which isn't listed here - SELinux is on enforcing on this one, so new bugs may arise :silly:
FAQ:
Does this ROM supports F2FS?
- Yes, on /data.
Will this get official?
- Yes, as soon as this is proven to be stable and relatively fast.
Does this ROM uses DDK 1.9?
- Yes, with all the camera issues (ie. pink lines, rare crashes) resolved.
Why does the initial boot take so long, and where are my live wallpapers?!
- To make room on the system partition for the (bigger) M gapps packages, I had to sacrifice dexpreopt and the live wallpapers. This can result in pretty long initial boots or upgrade boots, and dexpreopt might run during the first time setup wizard as well, slowing down the system for an additional couple minutes.
Want to support development? Consider donating, I spent countless of hours with this device
XDA:DevDB Information
OmniROM, ROM for the Samsung Galaxy Nexus
Contributors
Ziyan, MWisBest
Source Code: https://github.com/omnirom
ROM OS Version: 6.0.x Marshmallow
ROM Kernel: Linux 3.0.x
Based On: OmniROM
Version Information
Status: Beta
Created 2016-04-17
Last Updated 2016-04-17
Click to expand...
Click to collapse
wow i bought my 6p but you amaze me here more than any other dev
How to root
wow!!!!
Is based on Omap4 kernel ?
[edit]
I say alone: no! (880MB total memory)
Also not working my sim card.....
Nautilus74 said:
wow!!!!
Is based on Omap4 kernel ?
[edit]
I say alone: no! (880MB total memory)
Click to expand...
Click to collapse
CMA proved to be stable now, so I'll likely switch over the next build (possibly late next week). Time is starting to be an issue now, though...
Nautilus74 said:
Also not working my sim card....
Click to expand...
Click to collapse
Mine works, this is my daily driver since sometime now - what are the symptoms? Any logs?
unfortunately I did remove it immediately.... to return to AOSP OMAP4 !
...I have nothing to show you.......
symptoms: no sim card recognized
I have bootloop on maguro. I try flash this rom with gapps and without gapps. TWRP 2.7.8.0
Ziyan said:
Mine works, this is my daily driver since sometime now - what are the symptoms? Any logs?
Click to expand...
Click to collapse
Hi Ziyan,
IDK if it's the same error that Nautilus74 reported, but on the Omni I've build from source yesterday I got a rild avc denial and, obviously, no sim card recognized:
04-18 06:30:56.234 345 345 W rild : type=1400 audit(0.0:11): avc: denied { read } for name="mmcblk0p9" dev=tmpfs ino=2463 scontext=u:r:rild:s0 tcontext=ubject_r:block_device:s0 tclass=blk_file permissive=0
04-18 06:30:56.248 345 345 D : [CP BOOT] mipi_xmit_atat: SENT ATAT 1
04-18 06:30:56.249 345 345 E : File /dev/block/platform/omap/omap_hsmmc.0/by-name/radio open failed
04-18 06:30:56.249 345 345 E : [CP BOOT] mipi_xmit_psi: load PSI img failed : -1
04-18 06:30:56.249 345 345 F libc : Fatal signal 11 (SIGSEGV), code 1, fault addr 0x0 in tid 345 (rild)
Note that I've removed some repos when building so this error may come from my build and not from the rom itself.
Thank you for your hard work on GNex.
Best regards
yen
_yen_ said:
I got a rild avc denial and, obviously, no sim card recognized:
04-18 06:30:56.234 345 345 W rild : type=1400 audit(0.0:11): avc: denied { read } for name="mmcblk0p9" dev=tmpfs ino=2463 scontext=u:r:rild:s0 tcontext=ubject_r:block_device:s0 tclass=blk_file permissive=0
Click to expand...
Click to collapse
That's rather odd, it acts like if mmcblk0p9 wasn't labeled - but it is labeled (this is a symlink to mmcblk0p9, which also gets labeled). Just for the record, could you try a regular reboot, and see if the denial still pops up?
Ziyan said:
That's rather odd, it acts like if mmcblk0p9 wasn't labeled - but it is labeled (this is a symlink to mmcblk0p9, which also gets labeled). Just for the record, could you try a regular reboot, and see if the denial still pops up?
Click to expand...
Click to collapse
Nope, I restored my OMNI nandroid and rebooted two or three times, still same avc denial on rild.
I just synced sources and start compiling again, this time permissive to see if things get better. Sadly I'm very busy and idk when I can give a try to new build.
Just a little note, I'm currently using /hardware/ti/omap4 repo from TI OMAP4 AOSP as that from omni breaks my build.
Regards
yen
After long time of download first attemp zip corrupt and make MTP crash and I discover it because by adb sideload it tell my...
Second time downloading... 1hour can you mirror it to another site , maybe people is having problem with xda speed
Now rom is working i will comment how it goes
me too... not working sim card!
Sent from my Galaxy Nexus using XDA-Developers mobile app
Ziyan said:
Mine works, this is my daily driver since sometime now - what are the symptoms? Any logs?
Click to expand...
Click to collapse
I have just flashed the rom and also SIM card is not recognized.
I attached the logs in this post.
Hello nice rom, all is working so far. Thanks
Is there a theme manager available for this rom, please?
werty100 said:
After long time of download first attemp zip corrupt and make MTP crash and I discover it because by adb sideload it tell my...
Second time downloading... 1hour can you mirror it to another site , maybe people is having problem with xda speed
Now rom is working i will comment how it goes
Click to expand...
Click to collapse
No SIM working unknown baseband
werty100 said:
No SIM working unknown baseband
Click to expand...
Click to collapse
Okay, I'll need to inspect why's this bug only affecting some people then. Expect a new build later today or early tomorrow fixing this issue
Okay, here's a new boot.img (which contains an updated selinux rule), hoping to fix the ril denial. Report back if it works
Ziyan said:
Report back if it works
Click to expand...
Click to collapse
Thanks Ziyan,
I can confirm that new boot image solved the rild denial bug.
Thanks also for all the commits you just pushed on omnirom gerrit.
Regards
yen
I also can confirm that the new boot image fixes sim card issue.
Thanx.
Ziyan said:
Okay, I'll need to inspect why's this bug only affecting some people then. Expect a new build later today or early tomorrow fixing this issue
Click to expand...
Click to collapse
Ziyan said:
Okay, here's a new boot.img (which contains an updated selinux rule), hoping to fix the ril denial. Report back if it works
Click to expand...
Click to collapse
Thanks will try and sorry for no log i have no time..
Now yes it is working rild , another question why is not enable full ram only 880MBs avalible
Code:
*** Disclaimer***
No legal responsibility taken for anything.
use at own risk.
I am not a Developer . Just sharing the RR project with updates and mergers faster for users
Install with full knowledge that this might make your phone 100% unusable and will void your device warranty .
Briefing
This is my own personal RR N build, based on 14.1. i will build the ROM ASAP once crpalmer merges any new codes .
I will upload the ROM if it Boots fine in my personal device
i am not offending anybody's build especially the Official RR thread . i just keep this thread updated daily .
please dont complain anything about the BUGS as all bugs in CM14.1 are present in my build too
Feel free to contribute, recommendations and (new) bug reports are always very welcome.
I am a newbee here if any mistakes please let me know
Click to expand...
Click to collapse
Features & Details
FULL Substratum theme engine support with Masquerade and OMS
Compatible fully with both firmware (MM and N)
SELinux ENFORCING
Build USING Ubuntu 16.04 in Windows using VM
Click to expand...
Click to collapse
INSTRUCTIONS
Download the Rom & and ARM64 7.1 GAPPS .
Reboot to TWRP recovery .
Flash ROM and then GAPPS
Flash Custom Kernel ( Personal recomendation i am using V7.0.2-Beta Android N )
If running Nougat firmware (2.0+) you will need to flash fingerprint patch to use the home button
Click to expand...
Click to collapse
BUGS
Same as CM 14.1 ... i am not listing the bugs
ChangeLog
Add headphones backend (fixes headphones)
WIFI fix ( may be check it out yourself)
Developer settings fixed
USB tethering fixed ( working for me)
Night mode working
Bug fixes
VOIP application issue fixed when it comes for audio
Added Aptx Bluetooth Support
[*] Touch Screen Gestures added
Note :- please dont ask for BUG fixes FYI i am not a developer ... solutions and recommendations are welcome
Downloads
RR-N-v5.8.2-20170319-pme-Nightly.zip
Finally an OMS build .... No help got from any of the devs out here in XDA ... Finally managed to get the OMS in my build.
Thanks a lot to my best mate who helped me in guiding on github and gerrits ++ thanks @ mihran
GAPPS:-
Optional
substratum theme engine
XDAevDB Information
Resurrection Remix ROM N UNOFFICIAL for the HTC 10
Contributors crpalmer
Version Information
Status: Beta
Created 26.12.2016
Source Code Rom
https://github.com/vysakhraju/platform_manifest
Original Rom thread by @Eliminater
=[url]http://forum.xda-developers.com/htc-10/development/rom-resurrection-remix-m-t3440977[/URL]
Thanks alot!
Where is FP patch?
ali nz said:
Thanks alot!
Where is FP patch?
Click to expand...
Click to collapse
As i have not got the permission to use the finger print patch please use the one from CM14.1 thread by @ibrokemypie
@ibrokemypie :- Can i use your finger print patch for my ROM ?
Dec 26th Build with OMS updated in OP
OP I'm on your last build of RR unofficial from 12.22 from the other thread.
do you require or recommend a clean flash for this or can it flash dirty? thank you!
VR32 said:
OP I'm on your last build of RR unofficial from 12.22 from the other thread.
do you require or recommend a clean flash for this or can it flash dirty? thank you!
Click to expand...
Click to collapse
I did dirty flash and is wokring fine
thanks man I'll give it a go
Hi All
Need your support to add OMS support to this ROM
. I have does somebody know how to Clone / fetch the megers to my build ...
If someone know please comment so I can release the build tomorrow
ffs what is with the //word for word// copying now
one thing to build a rom using open source code, another entirely to copy an entire thread and change some words just enough to get past your teacher's plagiarism check.
ibrokemypie said:
ffs what is with the //word for word// copying now
one thing to build a rom using open source code, another entirely to copy an entire thread and change some words just enough to get past your teacher's plagiarism check.
Click to expand...
Click to collapse
As per the request and comments on RR thread i created a seperate thread for my build... To be frank yes copying was easy and i thougt of doing ..I have not spend much time in that lol.. Anyways I have not copied your build or work mate !!!
blackpanther0582 said:
As per the request and comments on RR thread i created a seperate thread for my build... To be frank yes copying was easy and i thougt of doing ..I have not spend much time in that lol.. Anyways I have not copied your build or work mate !!!
Click to expand...
Click to collapse
just to be clear, I never said nor insinuated that you copied my build, very difficult to do that anyway as being all open source, no one is copying anyone, simply building the same source code. Just frustrating to have ones words taken and repeated without permission, attribution or even a simple acknowledgement, and its suddenly something that has happened a lot in the past few days.
Really sorry mate ...yes I have not asked permission from you I apologizing for that ... I don't know how to create a thread while looking at your thread it was really a promising one just to start with .
I was at my work time though so just spend only few mjns for that ..
Sorry once again...
If you insist I will change the entire thread
thanks for building RR I'll keep an eye on this as it develops
Working like a dream for me. Really appreciate this.
(/w Nebula 7.0.2)
Tried to add full OMS support to my yesterdays build ... But I think I am missing some steps..
Without some devs support I think I might not be able to fix it
Finally an OMS included RR nightly has been uploaded... See the main thread for download Link...
Night mode / Live display works
RR-N-v5.8.0-20161228-pme-Nightly.zip
@blackpanther0582 could you compile this kernel?
https://github.com/CyanogenMod/android_kernel_htc_msm8996/commits/cm-14.1-caf
OMS(meaning substrarum) I installed from the Play Store on the 12/24 build seems to work fine. Wifi cuts out at random is that the bug everyone talks about? It just puts am X in it and says connected but no internet.
Sent from my HTC 10 using XDA-Developers mobile app
Nosferatu. said:
OMS(meaning substrarum) I installed from the Play Store on the 12/24 build seems to work fine. Wifi cuts out at random is that the bug everyone talks about? It just puts am X in it and says connected but no internet.
Sent from my HTC 10 using XDA-Developers mobile app
Click to expand...
Click to collapse
Same here on both counts. Gonna install the 28th build to check it the wifi's fixed. That's literally the only bug i need fixed to be 100% daily driver. So awesome how fast CM/RR came all the sudden.
holofractal said:
@blackpanther0582 could you compile this kernel?
https://github.com/CyanogenMod/android_kernel_htc_msm8996/commits/cm-14.1-caf
Click to expand...
Click to collapse
Will sure try
the original OP is VERY confusing. Take a look for credits sake though. I am putting a link to the download page below it.
I DIDN'T MAKE THIS ROM! All credit for the Droid Razr M build goes to elros34, also please thank vevgeniev for making the Photon Q port.
JBBL ONLY!!! -- I MIGHT be tempted to try and build a KKBL port if enough people are interested, but at the moment, JBBL works flawlessly, and a few KKBL users downgrading their Boot loaders is way easier than me building a whole new (most likely) barely functioning port just for KKBL, when we already have a great JBBL port
What works:
Camera
Wifi
GSM: Everything works, including calls, data, and text
CDMA: I don't use CDMA but as far as I know, only calls work.
Vibration
Audio and Video
>>*when using the YTPlayer app, turn off early video loading in Settings>Player>Early video loading = set it to "Never"*
USB MTP to both my PC and my Chromebook.
What doesn't work:
nothing, this is a ROCK SOLID PORT!
you have to first flash CM11, and then flash sailfish over it.
So I was browsing around the Photon Q xda page and saw this gem. I would have passed it over and just thought "neat" and moved on, but as I skimmed the page I saw that it is based on msm8960_jbbl sources, so it theoretically works on all unified msm8960 devices on jbbl. I actually read the OP and low and behold there is the RAZR M on the list of supported devices. I didn't make this (obviously) but definitely swing by the original thread and take a look.
NOTE: THE PHOTON Q PORT WON'T BOOT ON THE XT907 OR XT905 - Please use the elros34 build linked in the Direct Download links section.
https://forum.xda-developers.com/photon-q-4g-lte/general/sailfishos-2-0-motorola-photon-q-t3281262
http://www.vladislavonline.com/sailfishos-for-photon-q/
DIRECT DOWNLOAD LINKS
CM11 BASE [ https://archive.org/download/cmarch...626-SNAPSHOT-XNG3CAO1L8-moto_msm8960_jbbl.zip ]
Sailfish OS 2.1.3.7 alpha3 xt907 [ https://goo.gl/DJ8zre ] || Mirror [ https://onedrive.live.com/?cid=f188cb653189eae0&id=F188CB653189EAE0!403&authkey=!AGtl3flkGPJHaiE ]
rahimali AFH: [ https://androidfilehost.com/?w=files&flid=236124 ]
Headphone Jack fix for xt907 ---> HEADPHONE JACK FIXED IN ALPHA BUILD 3, THANKS elros34!!!
tested and working on the alpha 2 build, thank elros34 for this not me, he is the genius behind this one, think of me as a parrot.
You need to either use ssh on your computer, or the terminal app on your phone. You also need to set a root password in Settings -> Developer Options
devel-su
[input root password]
vim /etc/ohm/plugins.d/accessories.ini
*you'll see 4 lines, one of witch being Jack Match = /dev/input/event5 (or something similar, you'll see it, it should be the last line in the file)
*enter the letter "i" to edit
*replace "/dev/input/event5" with "/dev/input/event4"
*enter CTRL+C
*enter ":", and enter "write"
*now hit ":" again and enter "quit"
reboot your device and now headphone jack should work, hooray!
I DID NOT MAKE THIS!!! I AM SIMPLY LINKING IT FOR OTHER XT907 USERS TO ENJOY! CREDIT TO elros34 FOR THE PORT TO THE RAZR M, AND vevgeniev FOR MAKING THE PHOTON Q PORT!
The link doesn't seem to work. Says an error has occurred.
link is not working
faisala66 said:
link is not working
Click to expand...
Click to collapse
Ill update it :good:
The one drive links works fine on my chromebook, but Ill replace it with the direct one I find in the thread.
I've shared the files here
it is for kkbl?
faisala66 said:
it is for kkbl?
Click to expand...
Click to collapse
Nope. JBBL only.
rahimali said:
Nope. JBBL only.
Click to expand...
Click to collapse
but it says it is for kkbl and I have also installed in my phone in KKBL
faisala66 said:
but it says it is for kkbl and I have also installed in my phone in KKBL
Click to expand...
Click to collapse
Good for you! :good:
rahimali said:
Good for you! :good:
Click to expand...
Click to collapse
thanks but its not booting
faisala66 said:
thanks but its not booting
Click to expand...
Click to collapse
So what do you expect if you don't follow instructions?
rahimali said:
So what do you expect if you don't follow instructions?
Click to expand...
Click to collapse
sorry sorry i wlashed wrong CM11 snapshot (msm8960) it is for (msm8960jbbl) right:laugh::good:
its working great. but it is not android rom and i cant run apk
faisala66 said:
thanks but its not booting
Click to expand...
Click to collapse
then it's obviously only for jbbl, switch to jbbl if you want to use this, its a real quick 10 minute process, and since this is a GNU/Linux rom, the downgrade won't do much.
faisala66 said:
its working great. but it is not android rom and i cant run apk
Click to expand...
Click to collapse
well yeah, it isn't an android rom, so you won't be able to run android apps. It is a GNU/Linux based OS, the only way you will be able to run android apps is if you somehow hack in alien dalvik (edit platform manifest file, cross your fingers), or get one of the other android emulators set up. The reason you use Sailfish OS is because it is lightweight, fast, and a generally beautiful and fun to use OS.
It's stuck in the bootlogo here.
I used the CM11 mentioned in the OP (from here), SailfishOS 2.0.1.11 (from here) and ilichva's TWRP 3.0.2-1 (DiamondJohn's TWRP 3.1.1-1 failed with error 7). Both data and system partitions are ext4. Am I missing something? Thanks in advance.
hernandezjonathan21 said:
It's stuck in the bootlogo here.
I used the CM11 mentioned in the OP (from here), SailfishOS 2.0.1.11 (from here) and ilichva's TWRP 3.0.2-1 (DiamondJohn's TWRP 3.1.1-1 failed with error 7). Both data and system partitions are ext4. Am I missing something? Thanks in advance.
Click to expand...
Click to collapse
you are on JBBL right? I used that same zipe and rootfs and all is good.. you flashed the cm zip, then the sailfish zip on top without wiping anything right? and you wiped all your partitions (except internal and external sd of course) before hand?\
EDIT: You are using a photon Q build on xt907, no wonder it won't boot. grab the one from the bottom of the rahimali afh link or the xt907 one in the downloads section.
Galaxyninja66 said:
you are on JBBL right? I used that same zipe and rootfs and all is good.. you flashed the cm zip, then the sailfish zip on top without wiping anything right? and you wiped all your partitions (except internal and external sd of course) before hand?\
EDIT: You are using a photon Q build on xt907, no wonder it won't boot. grab the one from the bottom of the rahimali afh link or the xt907 one in the downloads section.
Click to expand...
Click to collapse
Alright, gotta try it ASAP (which means in a week or two :crying. Any fixes for the headphone jack?
EDIT: Nevermind, I just saw the updated OP. Now this is looking reaaaally good for a daily driver.
hernandezjonathan21 said:
Alright, gotta try it ASAP (which means in a week or two :crying. Any fixes for the headphone jack?
EDIT: Nevermind, I just saw the updated OP. Now this is looking reaaaally good for a daily driver.
Click to expand...
Click to collapse
headphone jack is being patched in the new update, elros34 should release it by tonight, he was messing with it on the IRC (it'll be based on the newest version of sail and have fixed headphone jack built in, hooray!!! )
I'm replying from Sailfish in my XT907! I tried to install the alpha 3 from @rahimali's folder and it didn't boot (I wasn't surprised though, as it said it was for XT897).
Battery seems to last waaay more than Android and it's really fun to use! I just need to find a way to use WhatsApp.
Hi everyone! Tonight I'm releasing my iOS 8.0 ROM which is based on LineageOS 13.0!
**** | ~WORKING~ | ****
Even though this is still an Alpha Build, everything seems to be working fine already
**** | ~NOT WORKING~ | ****
~ SELinux can't be changed to Enforcing, but that's related to the Base ROM aka LineageOS and also I do not have the knowledge to try to fix that.
**** | ~BUGS~ | ****
~ DualBoot Patcher (Preinstalled, but can be removed) shows the ROM being installed on "Data-Slot" but it's actually supposed to be on "Primary".
I will fix this in the next Builds
~ LineageOS's Stock Camera crashes when switching between Camera and Video, (Both are working though, but Camera Application has to be restarted) Use "Open Camera" to fix this Issue.
**** | ~FEATURES~ | ****
~ Carrier Name can be changed or hidden
~ Battery Percentage can be hidden or Displayed
~ Signal Strength can be hidden or Displayed
~ "Stock" Notificationbar can be accessed through opening the iOS Notificationbar, then swiping down again
~ Spotlight Search (Swipe down from Home Screen)
~ iOS Control Center
~ iOS Lockscreen with PIN Code Support
~ ROOT is included! (SuperSU)
ROM OS VERSION: iOS 8.0 (Android 6.0)
ROM KERNEL: 3.4.x
ROM VERSION REQUIRED: TWRP Recovery 3.2.1-0
BASED ON: LineageOS 13.0
Version Information:
STATUS: ALPHA / WIP
DEVICE: G800F
Created: 04/01/2018
Last Updated: No Update yet!
CHANGELOG:
Code:
04.01.2018 > Initial Release of Alpha 0.1
04.02.2018 > Due to Compatibility Issues the Current Base ROM [LOS 13] will be Updated/Changed, Alpha 2 for now is WIP!
04/02/2018 2:38AM UPDATE: Please see latest Post for further Information.
**** | How to Install | ****
Downloads
~ iOS 8.0 - Alpha 0.1
https://www.androidfilehost.com/?fid=962157660013069618
~ The ROM is completely Google-Free, Which means you need to download your Apps as APK File (I will add some Apps already Installed in the next Builds Just tell me which Apps you're using mostly )
Installation
Download the Backup.rar File, and extract it
in TWRP/BACKUPS/ then reboot to Recovery, wipe everything except /Internal Storage and /External SD, after that go to "Restore" and simply restore the Backup. After that you're done and another reboot will start your Device with the iOS ROM
NOTE: In some cases it might still show "No OS Installed" even after you successfully restored the Backup, but that can be ignored for now.
Can you take some screenshots of the rom?
DechnyLamtra13 said:
Can you take some screenshots of the rom?
Click to expand...
Click to collapse
+1
Reserved LOL
Screenshots:
I will test it,thanks!!!
Del.
Is this for G800F or G800H ?
another343 said:
Is this for G800F or G800H ?
Click to expand...
Click to collapse
It's for the G800F
I get an error when unzipping
Misma13 said:
I get an error when unzipping
Click to expand...
Click to collapse
Which Program do you use for unzipping?
EDIT: I downloaded the ROM again from the Link and extracted it with the app "RAR" and I didn't encounter any Errors.
i can't see the restore backuop. I made my own and i can restore it, but i just dont see yours.
why can i possible doing wrong? file explorer sees it, even the one built in the twrp..
qasq said:
i can't see the restore backuop. I made my own and i can restore it, but i just dont see yours.
why can i possible doing wrong? file explorer sees it, even the one built in the twrp..
Click to expand...
Click to collapse
Try moving the Backup to /TWRP/Backup/iOS-8 ROM/ so that the Backup files are in the iOS-8 ROM Folder, if that doesn't work then move only the Backup Files to /TWRP/Backup/
I will try to find a workaround for that, I did try to make an flashable ZIP first of the ROM but it instantly failed to flash somehow.
I tired all that, even tried from sdcard, backup doesn't seem to be seen the files at all, no matter what. I had many S devices, now I'm on S8+, i got almost all of them, but first time I see such issue I belive it's your fault somewhere or maybe TWRP sees that this is a backup from other device (same, but diffrent) and doesn't let me to use it!? Is there anyone else facing this issue ?
qasq said:
I tired all that, even tried from sdcard, backup doesn't seem to be seen the files at all, no matter what. I had many S devices, now I'm on S8+, i got almost all of them, but first time I see such issue I belive it's your fault somewhere or maybe TWRP sees that this is a backup from other device (same, but diffrent) and doesn't let me to use it!? Is there anyone else facing this issue ?
Click to expand...
Click to collapse
Well then the "Problem" is your Device Since this ROM is actually for the S5 Mini = kminiltexx
Fatal_Scythe said:
Well then the "Problem" is your Device Since this ROM is actually for the S5 Mini = kminiltexx
Click to expand...
Click to collapse
Yes, I know that. I've spelled the wrong thing. I hope this will clear the missunderstooding
Will there be any re to my last post?
qasq said:
Will there be any re to my last post?
Click to expand...
Click to collapse
Well what exactly do you mean / or what question do you want me to answer?