Spyder4 HCFR Color Results - 8.9" Kindle Fire HD Q&A, Help & Troubleshooting

As you can see in the attached results the device is has a green tint with red's that drop off in the blacks. Currently there is no way I know of to correct this. Screen Adjuster and Filter Your Screen only adjust the RGB Offset (Blacks) If you calibrate to the white point the black shifts very red. The device also appears to have a ridiculous gamma of 2.78
I used HCFR with a Spyder4Pro and the AVS HD 709 Patterns.

Related

Front LED - Interesting Question

Currently, is there ANY ROMs or applications that allows you PWM it?
Instead of blinking/flashing the LED in just variable colours, is it possible to make it glow from dim to bright, bright to dim?
Thanks

Is my screen bad?

When I put an all-black image on the screen (e.g., using LCD Test), while I am in a dark room, I see a faint gray glow from most of the screen, but there are also irregularly shaped areas of the screen that are blacker and don't glow as much. This is annoying when using the device at low screen intensity in the dark (with my ScreenDim app, for instance), or when using an astronomy app as I was tonight.
Do other people see the same irregularity?
I prefer the darker areas. There shouldn't be any gray glow where there are no bright pixels.
Another thing I noticed is that if I turn the intensity way down (with ScreenDim's contrast setting--Screen Filter should work the same way), and I mentally divide the portrait screen into thirds with vertical lines, then the middle third is a bit pinkish. Is that normal?

[FIX] Optimum Color Control Values for Purple Screen/Grain Issue [JB]

Well, after 5 months of looking out for the best values, I've experimented and all and found out these to be the best. Even at lowest brightness, the screen is crisp and clear just like it's supposed to be.
People who have the Purple Screen issue, I highly recommend you use these values.
Requirements -
1. Franco Kernel Updater (TKT wouldn't give that much brightness/crispyness to the screen)
2. ICS Gradient Fix (Check Signature)
3. Franco Kernel
First up, flash Franco's latest kernel.
Secondly, make sure you don't have any 2 or more applications which have Color Control options (Like, Franco Kernel Updater and TKT - Remove TKT and stay with Franco). If you do have 2 or more installed, please set all values to default on all applications including Franco's. (In TKT, click on menu and select reset preferences and reboot).
Third, fire up Franco Kernel Updater and get to the CC options and set these :
Color Multipliers -
Red - 280
Green - 292
Blue - 350
Gamma -
Red - 4
Green - 0
Blue - 9
Disable Contrast Adaptive Brightness - Yes (Tick)
Contrast Control : -24
OMAP Gamma - 1.2
These values work BEST with MoDaCo's JB Build. Tested on Jr1, Jr.1.1, Jr2.
Please note : This is simply a band aid, not a total fix. The purple screen and grain issue is probably a hardware issue. This settings are extremely crisp on my device. You need to get adapted to them.
Thanks to -
1. Franco for his amazing kernel and application.
2. Morfic for introducing contrast control into the kernel world and of course for his kindness. (You're the sweetest developer I've talked to).
Best of luck with these settings guys!
Please, don't forget to click "Thanks"!
It made everything look over-saturated for me.. plus, is it safe to jack up the settings like this?
It did improve the grainy screen on low brightness problem, though.
Well, i think the best values i've EVER Seen.
Oh dear, so f****ng awesome.
via Google Galaxy Nexus
Made my eyes hurt.. Too cold.. I'm trying to get my screen as close to 6500k as possible.
Sent from my Galaxy Nexus using Tapatalk 2
Thank you for this! By far the best optimization of colors I've ever seen. Maybe colors are a bit over-saturated but thats how Super AMOLED should produce.
Doesn't lacking the values up that high create burn in???
Sent from my Galaxy Nexus using xda premium
craigbailey1986 said:
Doesn't lacking the values up that high create burn in???
Sent from my Galaxy Nexus using xda premium
Click to expand...
Click to collapse
Try reducing every multiplier value by 40. 280 to 240, 292 to 252 and 300 to 260.
This can never be an all-in-one "fix" because of the way screen technology works. Everyone's screen will have different degrees of the problem itself (purple tint & grain), on top of that they will all have a slightly different color temperature, contrast level, saturation etc. By providing the values that worked for you, you're just going to have a thread where half the people think it looks great, half think it looks awful, and everyone thinks everyone else is crazy.
A better idea might be to describe the steps you took to arrive at your own numbers, things you looked for, how you tweaked them to get to the best values.
Look Excellent to me - Screen absolutely Pops, so vivid and the gradient issues are not visible.
Thanks so much!
Those high values are gonna kill your screen
OP settings work well for me (similar to my 200 215 280, -2 0 10, -23, CAB off), but OMAP always makes things worse IMO. With OMAP at 1.2 I instantly see banding again where with it off the gradients are smooth. OP settings with OMAP 1.0 are excellent however, reducing the magenta and yellowing I was seeing with my others. I am worried about the burn-in though..
What's this about burn in? Do these settings cause it?
I sort-of mispoke. Burn-in is possible, but high multipliers are more worried to wear out those pixels/degrade them faster.
Edit: I'm going for more of a "Trinity Blue" sort of solution now: 215 235 280, -2 0 15, -24, CAD off, OMAP unset. Still trying to find that balance that gets rid of the magenta/yellow at all points.
Okay guys try out 180,192 and 250 as the color multipliers. No burn issues then. I'm on it right now. Its great!
I'm using Trinity kernel, TKT, and Display Tester Pro for calibration. The gamma test shows that my particular settings should be red=2, green=3, blue=2. The color gamma settings are not relative to one another and are not "mixed together" for adjusting color. Each one is a separate adjustment for that color's correct level of brightness for midtones, relative to darkest and lightest levels. Together, the three settings add up to correct gray brightness levels, not to correct gray colorlessness.
If you look at a chart containing only black, 50% gray, and white, the color multipliers should be adjusted to remove any trace of color tint from the gray. The easiest way to do it is set the weakest color to 200 and reduce the other two colors until the gray has no color tint at all. The properly set color gamma settings, on the other hand, should make the 50% gray have the correct lightness level.
If you have yellow tint, there's not enough blue. Magenta tint means not enough green. Cyan tint, not enough red.
The color multipliers, unlike the gamma settings, are relative to one another. Once you have them set correctly relative to one another, moving them all up or all down together pnly changes the overall brightness of the display. The wrong overall brightness level will remove detail from either the black end or the white end. Too much brightness is also bad for the screen, not to mention battery drain.
So anyway I'll shut up now and I hope everyone gets their screens looking perfect.
gsm gnex / cm9 / trinity / 1420 MHz
for whatever reason trinity seems to be giving me better screen color, but im sure I could do the same with franco, anyways, my gamma settings are untouched, I found that modifying the color to these values makes the purple tint go away for me:
Red:135
Green:135
Blue:190
Trinity Contrast -15 to -25
Have you tried adjusting it for 18% gray? I can nail it pretty close with 180,150,190 and 8,0,8 but gamma is a complete ***** on this display...
strumcat said:
I'm using Trinity kernel, TKT, and Display Tester Pro for calibration. The gamma test shows that my particular settings should be red=2, green=3, blue=2. The color gamma settings are not relative to one another and are not "mixed together" for adjusting color. Each one is a separate adjustment for that color's correct level of brightness for midtones, relative to darkest and lightest levels. Together, the three settings add up to correct gray brightness levels, not to correct gray colorlessness.
If you look at a chart containing only black, 50% gray, and white, the color multipliers should be adjusted to remove any trace of color tint from the gray. The easiest way to do it is set the weakest color to 200 and reduce the other two colors until the gray has no color tint at all. The properly set color gamma settings, on the other hand, should make the 50% gray have the correct lightness level.
If you have yellow tint, there's not enough blue. Magenta tint means not enough green. Cyan tint, not enough red.
The color multipliers, unlike the gamma settings, are relative to one another. Once you have them set correctly relative to one another, moving them all up or all down together pnly changes the overall brightness of the display. The wrong overall brightness level will remove detail from either the black end or the white end. Too much brightness is also bad for the screen, not to mention battery drain.
So anyway I'll shut up now and I hope everyone gets their screens looking perfect.
gsm gnex / cm9 / trinity / 1420 MHz
Click to expand...
Click to collapse
arzbhatia said:
Okay guys try out 180,192 and 250 as the color multipliers. No burn issues then. I'm on it right now. Its great!
Click to expand...
Click to collapse
It's been discussed few times already - going above 200 can lead to screen burn in. On SAMOLED screens blue color wear out first and peeps really shouldn't touch this setting. Better set lower red/green values. Screen will look a bit darker so don't cranck up contrast too much, -10 should be good enough.
herzzreh said:
Made my eyes hurt.. Too cold.. I'm trying to get my screen as close to 6500k as possible.
Sent from my Galaxy Nexus using Tapatalk 2
Click to expand...
Click to collapse
look at the graphs.
http://forum.xda-developers.com/showpost.php?p=29037317&postcount=1
herzzreh said:
Have you tried adjusting it for 18% gray? I can nail it pretty close with 180,150,190 and 8,0,8 but gamma is a complete ***** on this display...
Click to expand...
Click to collapse
You can see where your gamma should by by installing the free version of Display Tester from the Play Store. Go to Color, Gamma, and slide the gray screen to the left to see the red page. Find the vertical bar that most closely matches the red bacground. The number on that bar is where your gamma should be set for that color. Mine is spot on at 2.3. Then slide to green page and do the same. Then the blue page. My green gamma reading is 2.8, meaning it isn't quite as bright as the red or blue, so I have to turn it up a hair. My blue is good at 2.3. The adjustment sliders in TKT only give me whole-number choices, so I get as close as possible with 2, 3, 2. I'm just guessing there, since TKT doesn't have normal gamma increments. Anyway good luck taming your gamma.
galaxy nexus (gsm) / cm9 / trinity @ 1.4GHz

display color setting

hello
Is it the software or the way in which the three primary colors red, green and blue high or low on the screen.
Android is there a way to adjust the screen colors
marlikcoc said:
hello
Is it the software or the way in which the three primary colors red, green and blue high or low on the screen.
Android is there a way to adjust the screen colors
Click to expand...
Click to collapse
I don't think so... Kindle had issues and never got a utility to adjust it.
I checked my colors against my TV which is calibrated. Factory ROM gives a darn good picture, for such a device. Some overly reds but with proper brightness they are less noticeable. I don't know what setting you have the display on, I set mine for movie and leave it there. Dynamic and Standard is not good for Movies and Pictures. Though if you play games Dynamic may help. Standard is basic for reading and browsing.
Hope that helps

What display color settings are you using?

As topic says, what color settings are you using? Any of the preset profiles or your own expert settings? I have been playing around with the settings in the expert mode, but can't really find anything that looks better than the auto setting.
If you are using your custom expert settings, please post a screenshot of it here.
According to some reviews I've read, Expert with the warmth cranked all the way up was the "most accurate". I didn't really like how this looked as it just made the display look more red, not necessarily "warmer". I settled on Expert with the Red and Blue sliders dialed back one notch. I also cranked up the saturation one step and dialed back the sharpness slightly. This resulted in a bit of a warmer and sharper image that I'm content with but I really miss KCAL.
EDIT: Anandtech just released their review of this phone. They recommend that you use the "Expert" Color settings and turn the blue slider all the way down. It looks better but the display is still way too blue.
I use Expert.
Color Temperature is at 50%.
Red is at 100%.
Green is at 100%.
Blue is at 50%.
Saturation is at 100%
Hue is at 50%.
Sharpness is at 50%.
Color Filter is set to off.
I use Expert. Im searching a better black
Color Temperature is at 100%.
Red is at 0%.
Green is at 100%.
Blue is at 0%.
Saturation is at 100%
Hue is at 75%.
Sharpness is at 75%.
Color Filter is set to off.
try it!
Using expert
Saturation 50%
Hue 25%
Sharpness 0
Color temperature 75%
Red 50%
Green 75%
Blue 25%
This is what looks best to my eyes after time spent fiddling with it.
Auto with Comfort View "always on".
Now that and if I switch off comfort view or look at other phones I can clearly figure out the "blueness". The comfort view on the G7 is an excellent setting and something users should use of a couple of hours and feel the difference.
What makes color filer

Categories

Resources