Its been a while since flashing roms and I was going to sell my one x but needed stock software and unrooting. But I have ended up with my phone stuck in fast boot with it saying re locked at the top. I think i know where I went wrong but its too late. I dont have any backup because it was ages ago and I have tried various stock roms all returning errors. This is what I was following:
"fastboot oem Lock"
2) "fastboot oem rebootRUU"
3) "fastboot flash zip firmware.zip"
4) "fastboot reboot-bootloader"
5) "fastboot flash "unlocktoken Unlocktoken.bin"
6 "fastboot flash recovery openrecovery-twrp-2.6.3.0-4.18.401.2-endeavoru-JB.img
7) fastboot flash boot ( the boot.img from the custom rom)
8) go in to recovery and install the custom rom.
I got stuck at 6 giving me an error, I presume it was the wrong file.
Do I actually have to do fastboot oem Lock, because its relocked?
Could anybody help me out with what stock roms and file I need please? I know there are a lot of posts but each one is idividual and with different firmware.
Thanks Guys
This is some of my info:
c:\fastboot>fastboot getvar all
INFOversion: 0.5a
INFOversion-bootloader: 1.39.0000
INFOversion-baseband: 5.1204.164.30H
INFOversion-cpld: None
INFOversion-microp: None
INFOversion-main: 3.14.771.34
INFOserialno: ***********************
INFOimei: ********************
INFOproduct: endeavoru
INFOplatform: HBOOT-T30S
INFOmodelid: PJ4610000
INFOcidnum: H3G__001
INFObattery-status: good
INFObattery-voltage: 3759mV
INFOdevpower: 27
INFOpartition-layout: None
INFOsecurity: on
INFObuild-mode: SHIP
INFOboot-mode: FASTBOOT
INFOcommitno-bootloader: None
INFOhbootpreupdate: 2
INFOgencheckpt: 0
all: Done!
Will it unlock if I send a new unlock ticket through htc dev website?
si_d_2003 said:
Its been a while since flashing roms and I was going to sell my one x but needed stock software and unrooting. But I have ended up with my phone stuck in fast boot with it saying re locked at the top. I think i know where I went wrong but its too late. I dont have any backup because it was ages ago and I have tried various stock roms all returning errors. This is what I was following:
"fastboot oem Lock"
2) "fastboot oem rebootRUU"
3) "fastboot flash zip firmware.zip"
4) "fastboot reboot-bootloader"
5) "fastboot flash "unlocktoken Unlocktoken.bin"
6 "fastboot flash recovery openrecovery-twrp-2.6.3.0-4.18.401.2-endeavoru-JB.img
7) fastboot flash boot ( the boot.img from the custom rom)
8) go in to recovery and install the custom rom.
I got stuck at 6 giving me an error, I presume it was the wrong file.
Do I actually have to do fastboot oem Lock, because its relocked?
Could anybody help me out with what stock roms and file I need please? I know there are a lot of posts but each one is idividual and with different firmware.
Thanks Guys
This is some of my info:
c:\fastboot>fastboot getvar all
INFOversion: 0.5a
INFOversion-bootloader: 1.39.0000
INFOversion-baseband: 5.1204.164.30H
INFOversion-cpld: None
INFOversion-microp: None
INFOversion-main: 3.14.771.34
INFOserialno: ***********************
INFOimei: ********************
INFOproduct: endeavoru
INFOplatform: HBOOT-T30S
INFOmodelid: PJ4610000
INFOcidnum: H3G__001
INFObattery-status: good
INFObattery-voltage: 3759mV
INFOdevpower: 27
INFOpartition-layout: None
INFOsecurity: on
INFObuild-mode: SHIP
INFOboot-mode: FASTBOOT
INFOcommitno-bootloader: None
INFOhbootpreupdate: 2
INFOgencheckpt: 0
all: Done!
Will it unlock if I send a new unlock ticket through htc dev website?
Click to expand...
Click to collapse
I've got the same phone as you, i'll upload my H3G_001 backup of Jelly Bean
You will need to use Phillz Recovery or Clockwork Mod Recovery
---------- Post added at 03:23 PM ---------- Previous post was at 02:49 PM ----------
wigankev said:
I've got the same phone as you, i'll upload my H3G_001 backup of Jelly Bean
You will need to use Phillz Recovery or Clockwork Mod Recovery
Click to expand...
Click to collapse
https://dl.dropboxusercontent.com/u/92848413/H3G_001%20JellyBean.zip just unzip it flash Phillz or Clockwork Mod Recovery.
wigankev said:
I've got the same phone as you, i'll upload my H3G_001 backup of Jelly Bean
You will need to use Phillz Recovery or Clockwork Mod Recovery
Click to expand...
Click to collapse
Awesome mate, your a legend!
When you say to use phillz or cmr, can I use these because all I can do is access the fastboot screen? Even if I select recovery in fastboot the htc quietly brilliant screen pops up then goes back to fast boot menu.
si_d_2003 said:
Awesome mate, your a legend!
When you say to use phillz or cmr, can I use these because all I can do is access the fastboot screen? Even if I select recovery in fastboot the htc quietly brilliant screen pops up then goes back to fast boot menu.
Click to expand...
Click to collapse
Go on to HTC Dev and get another unlock token, and proceed to unlock again, then flash CWM or Phillz, then recover your phone with the backup i provided. I have also provided the stock htc recovery in the folder seperately.
wigankev said:
Go on to HTC Dev and get another unlock token, and proceed to unlock again, then flash CWM or Phillz, then recover your phone with the backup i provided. I have also provided the stock htc recovery in the folder seperately.
Click to expand...
Click to collapse
Ok Cheers dude, I will give them a while and let you know. Thanks for the help:good:
wigankev said:
Go on to HTC Dev and get another unlock token, and proceed to unlock again, then flash CWM or Phillz, then recover your phone with the backup i provided. I have also provided the stock htc recovery in the folder seperately.
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=1604439 i recommend using this to unlock bootloader with the token you received from HTC Dev.
Ok, so got it unlocked again, my viper rom was still installed so the phone boots up. Now to get your jelly bean on correct me if Im wrong, your jellybean zip, shall i unzip it? what shall i do with .img file and the others?
si_d_2003 said:
Ok, so got it unlocked again, my viper rom was still installed so the phone boots up. Now to get your jelly bean on correct me if Im wrong, all i do is put the zip on the phones hd the boot into recovery and then select restore? Just tried it and it says no file found, does your back up go into a specific folder? or just select install from zip?
Click to expand...
Click to collapse
No, on Clockword Mod or Phillz recovery you use Backup and Restore option, you don't flash the zip file, i zipped it up so i could upload to dropbox, just flash the 2013-02-05.20.39.08 folder under restore, there should be a folder called Clockword Mod on your SD Card or something like that.
Sorry for being an idiot im just concerned because I was up till 4.30 this morning trying to sort this out. in cwm folder is one called downloads which goes into recoveries folder, does the folder 2013....go in there? Then by flash do you mean going to fast boot- backup/restore - restore? because it says no file found still.
si_d_2003 said:
Sorry for being an idiot im just concerned because I was up till 4.30 this morning trying to sort this out. in cwm folder is one called downloads which goes into recoveries folder, does the folder 2013....go in there? Then by flash do you mean going to fast boot- backup/restore - restore? because it says no file found still.
Click to expand...
Click to collapse
On your storage you should have a file called clockworkmod and inside that you should have another folder in there called backup, so your 2013-02-05.20.39.08 file should be in that backup folder.
wigankev said:
On your storage you should have a file called clockworkmod and inside that you should have another folder in there called backup, so your 2013-02-05.20.39.08 file should be in that backup folder.
Click to expand...
Click to collapse
Sorry there is no back up folder in there. Ive tried installing phillz over cwm it says complete but after flashing and when i reboot its still cwm. and in rom manager when I try to update cwm it gives me an error.
wigankev said:
On your storage you should have a file called clockworkmod and inside that you should have another folder in there called backup, so your 2013-02-05.20.39.08 file should be in that backup folder.
Click to expand...
Click to collapse
So then go into CWM or Phillz recovery then go to Backup and Restore and restore that 2013-02-05.20.39.08 file, then you should be back on stock H3G rom, then just flash the recovery i put in the folder separately, then you should be fully stock, then relock your Hboot/bootloader then you should be able to update your rom OTA to 4.2.2 and hboot to 1.72
Ok, so finally got there in the end. Hopefully. I have one more question and i will leave you alone.....ive sent the lock message and the bootloader now says relocked again. Is this different from locked? Can i get it to say locked instead of relocked as this looks like its been rooted before?
Thanks
si_d_2003 said:
Ok, so finally got there in the end. Hopefully. I have one more question and i will leave you alone.....ive sent the lock message and the bootloader now says relocked again. Is this different from locked? Can i get it to say locked instead of relocked as this looks like its been rooted before?
Thanks
Click to expand...
Click to collapse
Relocked is correct, did you remember to flash the original htc recovery before relocking?
I did, but.....F### its stuck in bootloader loop now. The bloody phone booted and everything then when I restarted it its now stuck looping.
ok after unlocking the phone boots up fine. Is there something wrong when i go to lock it the it wont boot up?
Cheers dude
si_d_2003 said:
Whats the problem do you think? does that mean I have to:
unroot and install the the files you gave me then lock again. I cant even access recovery in the bootloader
Click to expand...
Click to collapse
are you flash the boot.img from your nand backup via fastboot?
Thant said:
are you flash the boot.img from your nand backup via fastboot?
Click to expand...
Click to collapse
No i didnt do that, I just recovered the nand via cwm, then I flashed recovery.img then locked it. It was stuck in loop then as soon as I unlocked it booted.
si_d_2003 said:
No i didnt do that, I just recovered the nand via cwm, then I flashed recovery.img then locked it. It was stuck in loop then as soon as I unlocked it booted.
Click to expand...
Click to collapse
now take the boot.img from nand backup and flash it via fastboot with the command fastboot flash boot nameofboot.img but you must unlock it again and after this relock it again
Ok cool, that looks like its worked. Thanks for that buddy! Do you know if there is any way to change the ****relocked*** back to ***locked***
Related
I hope that this post is in the correct forum section - apologies if not and apologies if there is already a thread on this subject (I did try searching but nothing that provided a link to a RUU).
Here's what I've done:
Flashed a custom ROM to my UK O2 HTC One X
Then tried to restore it to stock without taking a Clockwork recovery backup (deleted all caches and storage in the process)
Tried to flash with stock RUU found online (1.26.206.2) but RUU software throws an error as the exisiting f/w is 1.29.206.11 and this is what it is expecting
I can access the HOX through fastboot to lock and unlock the device but I cannot see the "SD card" to copy over a custom ROM to at least get some life into the thing (it just sits at the white HTC loading screen until the battery dies).
Ideally I want to return the thing to stock (if anyone has a O2 UK 1.29.206.11 RUU) but failing that is there anyway to get a custom ROM on there (for installation with CWM) without my PC (Windows 7 or Mac available) seeing the HOX storage?
Thanks for reading and any help you can pass on.
brlauk_HOX said:
I hope that this post is in the correct forum section - apologies if not and apologies if there is already a thread on this subject (I did try searching but nothing that provided a link to a RUU).
Here's what I've done:
Flashed a custom ROM to my UK O2 HTC One X
Then tried to restore it to stock without taking a Clockwork recovery backup (deleted all caches and storage in the process)
Tried to flash with stock RUU found online (1.26.206.2) but RUU software throws an error as the exisiting f/w is 1.29.206.11 and this is what it is expecting
I can access the HOX through fastboot to lock and unlock the device but I cannot see the "SD card" to copy over a custom ROM to at least get some life into the thing (it just sits at the white HTC loading screen until the battery dies).
Ideally I want to return the thing to stock (if anyone has a O2 UK 1.29.206.11 RUU) but failing that is there anyway to get a custom ROM on there (for installation with CWM) without my PC (Windows 7 or Mac available) seeing the HOX storage?
Thanks for reading and any help you can pass on.
Click to expand...
Click to collapse
if you can get into to CWM there is an option to mount sd in there somewhere, if you can't get into it maybe try re-flashing it
seanicca said:
if you can get into to CWM there is an option to mount sd in there somewhere, if you can't get into it maybe try re-flashing it
Click to expand...
Click to collapse
Thanks for the reply - I tried that but CWM returns an error when trying to mount the SD card.
Tried flashing 1.26.206.2 through fast boot?
brlauk_HOX said:
Thanks for the reply - I tried that but CWM returns an error when trying to mount the SD card.
Click to expand...
Click to collapse
Cwm 5.8.4.0 allows sd mounting in recovery, try flashing that
sent from my One X using xda venom premium
xmoo said:
Tried flashing 1.26.206.2 through fast boot?
Click to expand...
Click to collapse
DO you mean extracting the 2 img files from the RUU zip and running from fastboot command prompt? If so, the second img file returns a [0000006] error.
brlauk_HOX said:
DO you mean extracting the 2 img files from the RUU zip and running from fastboot command prompt? If so, the second img file returns a [0000006] error.
Click to expand...
Click to collapse
Get the rom.zip and
adb reboot oem-78
fastboot flash zip rom.zip
http://forum.xda-developers.com/showthread.php?p=28665193
Sent from my HTC One X
I'm looking for this Nandroid too but all the links I've found are broken. Can anyone help out? Preferably a CWM backup if at all possible.
brlauk_HOX said:
I hope that this post is in the correct forum section - apologies if not and apologies if there is already a thread on this subject (I did try searching but nothing that provided a link to a RUU).
Here's what I've done:
Flashed a custom ROM to my UK O2 HTC One X
Then tried to restore it to stock without taking a Clockwork recovery backup (deleted all caches and storage in the process)
Tried to flash with stock RUU found online (1.26.206.2) but RUU software throws an error as the exisiting f/w is 1.29.206.11 and this is what it is expecting
I can access the HOX through fastboot to lock and unlock the device but I cannot see the "SD card" to copy over a custom ROM to at least get some life into the thing (it just sits at the white HTC loading screen until the battery dies).
Ideally I want to return the thing to stock (if anyone has a O2 UK 1.29.206.11 RUU) but failing that is there anyway to get a custom ROM on there (for installation with CWM) without my PC (Windows 7 or Mac available) seeing the HOX storage?
Thanks for reading and any help you can pass on.
Click to expand...
Click to collapse
blocka said:
I'm looking for this Nandroid too but all the links I've found are broken. Can anyone help out? Preferably a CWM backup if at all possible.
Click to expand...
Click to collapse
Install directly the RUU 1.26.206.2
Thant said:
Install directly the RUU 1.26.206.2
Click to expand...
Click to collapse
thank you appreciate the link
Thant said:
Install directly the RUU 1.26.206.2
Click to expand...
Click to collapse
BTW my HBOOT version is 0.96, this won't cause any issues will it when it comes to running the RUU?
blocka said:
BTW my HBOOT version is 0.96, this won't cause any issues will it when it comes to running the RUU?
Click to expand...
Click to collapse
Please post the result from command fastboot getvar all and delete IMEI and S/N
Thant said:
Please post the result from command fastboot getvar all and delete IMEI and S/N
Click to expand...
Click to collapse
fastboot getvar all
INFOversion: 0.5a
INFOversion-bootloader: 0.96.0000
INFOversion-baseband: None
INFOversion-cpld: None
INFOversion-microp: None
INFOversion-main: 1.29.206.11
INFOserialno: xxxxxxxxxxxxx
INFOimei: xxxxxxxxxxxxxxx
INFOproduct: endeavoru
INFOplatform: HBOOT-T30S
INFOmodelid: PJ4610000
INFOcidnum: None
INFObattery-status: good
INFObattery-voltage: 4148mV
INFOdevpower: 100
INFOpartition-layout: None
INFOsecurity: on
INFObuild-mode: SHIP
INFOboot-mode: FASTBOOT
INFOcommitno-bootloader: None
INFOhbootpreupdate: 2
INFOgencheckpt: 0
all: Done!
finished. total time: 1.172s
fastboot oem readcid
... INFODEBUG: cid: O2___001
blocka said:
fastboot getvar all
INFOversion: 0.5a
INFOversion-bootloader: 0.96.0000
INFOversion-baseband: None
INFOversion-cpld: None
INFOversion-microp: None
INFOversion-main: 1.29.206.11
INFOserialno: xxxxxxxxxxxxx
INFOimei: xxxxxxxxxxxxxxx
INFOproduct: endeavoru
INFOplatform: HBOOT-T30S
INFOmodelid: PJ4610000
INFOcidnum: None
INFObattery-status: good
INFObattery-voltage: 4148mV
INFOdevpower: 100
INFOpartition-layout: None
INFOsecurity: on
INFObuild-mode: SHIP
INFOboot-mode: FASTBOOT
INFOcommitno-bootloader: None
INFOhbootpreupdate: 2
INFOgencheckpt: 0
all: Done!
finished. total time: 1.172s
fastboot oem readcid
... INFODEBUG: cid: O2___001
Click to expand...
Click to collapse
Ok in this case Download RUU 2.17.206.2 and run the RUU the RUU 1.26.206.2 will not work for you. Lock the bootloader and run the RUU
Thant said:
Ok in this case Download RUU 2.17.207.2 and run the RUU the RUU 1.267.206.2 will not work for you.
Click to expand...
Click to collapse
Cheers! can you explain to a noob why this is the case? BTW the file in the link is only 15MB, is this the correct file size?
blocka said:
Cheers! can you explain to a noob why this is the case? BTW the file in the link is only 15MB, is this the correct file size?
Click to expand...
Click to collapse
Ok this is bad this RUU is not full must be 500-600 Mb= Surch from google to download the RUU 2.17.206.2 for HTC one X and install this in Android RUU files store is not the full. The case is you have 1.29.206.11 witch is newer vrom 1.26.206.2 and if you try to install it you will receive error wrong RUU.
EDIT: I think you will not find this RUU surch here in xda for nandroid backup for 1.29.206.11 and restor it and dont forget to restor the stock recovery too.
Thant said:
Ok this is bad this RUU is not full must be 500-600 Mb= Surch from google to download the RUU 2.17.206.2 for HTC one X and install this in Android RUU files store is not the full. The case is you have 1.29.206.11 witch is newer vrom 1.26.206.2 and if you try to install it you will receive error wrong RUU.
EDIT: I think you will not find this RUU surch here in xda for nandroid backup for 1.29.206.11 and restor it and dont forget to restor the stock recovery too.
Click to expand...
Click to collapse
Thanks for your help, appreciate it!
I've got the RUU you suggested from HERE
Now to apply this RUU all I need to do is run the file (exe) and follow the bouncing ball?
Then once flashed (back to stock), to install a custom recovery (so I can do a nandroid) is unlock the bootloader, install the recovery, and take the nandroid backup. To get the OTA Update(s), I'll need to relock the bootloader, do the automated system updater, redo nandroid, then onto a custom recovery once HBOOT has been updated via the OTA process?
EDIT: Take a nandroid backup first of course
blocka said:
Thanks for your help, appreciate it!
I've got the RUU you suggested from HERE
Now to apply this RUU all I need to do is run the file (exe) and follow the bouncing ball?
Then once flashed (back to stock), to install a custom recovery (so I can do a nandroid) is unlock the bootloader, install the recovery, and take the nandroid backup. To get the OTA Update(s), I'll need to relock the bootloader, do the automated system updater, redo nandroid, then onto a custom recovery once HBOOT has been updated via the OTA process?
EDIT: Take a nandroid backup first of course
Click to expand...
Click to collapse
NO You can't receive the OTA via custom recovery you need ctock recovery and stock rom unrooted
1) Lock your bootloader
2) Run the RUU
3) Apllay all update to 4.x.206.x 4.2.2 JB
4) Unlock your Bootloader
5) Install Philz custom recovery
6) Do a Nandroid Backup on 4.2.2.JB . Save on secure plase it is better to have 2 copies on nandroid on different place
7) If you wont Install custom rom or root the stock it is your decision and don't forget to flash the boot.img if you install custom rom
Thant said:
Ok in this case Download RUU 2.17.207.2 and run the RUU the RUU 1.26.206.2 will not work for you. Lock the bootloader and run the RUU
Click to expand...
Click to collapse
Hi - was just about to go through the process of reverting to stock when I noticed the RUU and link you suggested
Download RUU 2.17.207.2
Click to expand...
Click to collapse
actually is linked to RUU_ENDEAVOR_U_ICS_40_S_O2_UK_2.17.206.2_Radio_2.1204.135.20_release_275038_signed.exe.
So before I start I need to find out exactly what RUU I need, either 2.17.206.2 or 2.17.207.2.
Thanks for ya help .
Hello,
I've been using ViperX 2.7.1 for an year, almost. I want to install the latest ViperX ROM, the JB version but unfortunately the hboot I have is not compatible with the JB versions of ViperX, my phone is slow now because of excess of apps and ****, I wanna reset the phone with a new ROM, how can I upgrade my hboot version to install the latest ROM? Please help.
Bijwa
Bijwa said:
Hello,
I've been using ViperX 2.7.1 for an year, almost. I want to install the latest ViperX ROM, the JB version but unfortunately the hboot I have is not compatible with the JB versions of ViperX, my phone is slow now because of excess of apps and ****, I wanna reset the phone with a new ROM, how can I upgrade my hboot version to install the latest ROM? Please help.
Bijwa
Click to expand...
Click to collapse
post the result from command fastboot getvar all and delete the IMEI and S/N
Thant said:
post the result from command fastboot getvar all and delete the IMEI and S/N
Click to expand...
Click to collapse
I don't understand :S
I'm not an expert or anything, please guide step by step
Bijwa said:
I don't understand :S
I'm not an expert or anything, please guide step by step
Click to expand...
Click to collapse
OK Download this unzip in folder fastboot and enter in the folder pres SHIFT + right mouse button choice Open command window here Shutdown your phone press volume down button + power button to go in bootloader connest the phone to computer you will see on your phone Fastboot USB in the CMD runt the command fastboot getvar all and post the resulte here and delete your IMEI and S/N information.
I hope you are with the windows
Thant said:
OK Download unzip in folder fastboot and enter in the folder pres SHIFT + right mouse button choice Open command window here Shutdown your phone press volume down button + power button to go in bootloader connest the phone to computer you will see on your phone Fastboot USB in the CMD runt the command fastboot getvar all and post the resulte here and delete your IMEI and S/N information.
I hope you are with the windows
Click to expand...
Click to collapse
INFOversion: 0.5a
INFOversion-bootloader: 1.12.000
INFOversion-baseband: 1.1204.105
INFOversion-cpld: None
INFOversion-microp: None
INFOversion-main: 2.17.720.2
INFOserialno: ***********************
INFOimei: ***********************
INFOproduct: endeavoru
INFOplatform: HBOOT-T30S
INFOmodelid: PJ4610000
INFOcidnum: HTC__038
INFObattery-status: good
INFObattery-voltage: 4151mV
INFOdevpower: 100
INFOpartition-layout: None
INFOsecurity: on
INFObuild-mode: SHIP
INFOboot-mode: FASTBOOT
INFOcommitno-bootloader: None
INFOhbootpreupdate: 2
INFOgencheckpt: 0
all: Done!
Bijwa said:
INFOversion: 0.5a
INFOversion-bootloader: 1.12.000
INFOversion-baseband: 1.1204.105
INFOversion-cpld: None
INFOversion-microp: None
INFOversion-main: 2.17.720.2
INFOserialno: ***********************
INFOimei: ***********************
INFOproduct: endeavoru
INFOplatform: HBOOT-T30S
INFOmodelid: PJ4610000
INFOcidnum: HTC__038
INFObattery-status: good
INFObattery-voltage: 4151mV
INFOdevpower: 100
INFOpartition-layout: None
INFOsecurity: on
INFObuild-mode: SHIP
INFOboot-mode: FASTBOOT
INFOcommitno-bootloader: None
INFOhbootpreupdate: 2
INFOgencheckpt: 0
all: Done!
Click to expand...
Click to collapse
It is better for you to install nandroid backup for 2.17.720.2 and receive the all ota to hboot1.72 or if you can find the firmware from latest ot and flash it manualy
Do you know how to flash manually the firmware?
Thant said:
OK Download unzip in folder fastboot and enter in the folder pres SHIFT + right mouse button choice Open command window here Shutdown your phone press volume down button + power button to go in bootloader connest the phone to computer you will see on your phone Fastboot USB in the CMD runt the command fastboot getvar all and post the resulte here and delete your IMEI and S/N information.
I hope you are with the windows
Click to expand...
Click to collapse
Thant said:
It is better for you to install nandroid backup for 2.17.720.2 and receive the all ota to hboot1.72 or if you can find the firmware from latest ot and flash it manualy
Click to expand...
Click to collapse
I have ClockWorkMod, is it possible to do it with this? Where can I find this nandroid backup? Will I have to unroot my phone again?
If I use an RUU will it work?
Bijwa said:
I have ClockWorkMod, is it possible to do it with this? Where can I find this nandroid backup? Will I have to unroot my phone again?
If I use an RUU will it work?
Click to expand...
Click to collapse
The RUU it will work but you must to find 2.17.720.2 RUU I can find this RUU. If you update manualy the firmaware you must to install again Custom recovery after flash the firmware and it will be to be Philz recovery. After this you can flash the Viper X
This is for advanced USer only if you not feel advanced don't try please
CHARGE YOUR PHONE TO 100%
Download the rom and copy to your SD Card
The firmware.zip you can download from HERE.
1) Make sure you have your Unlock_code.bin file.
Relock your device using fastboot: fastboot oem lock
Enter OEM flash mode using fastboot: fastboot oem rebootRUU
On your phone you will see a black screen with silver HTC written in the middle
Flash firmware: fastboot flash zip firmware.zip must be in your fastboot directory
(You need to do this immediately twice)
When you see a full green bar below, you are done.
3) Manually boot into fastboot on your device. Power off -> Power+ volume down
4) Unlock device: fastboot flash unlocktoken Unlock_code.bin must be in your fastboot directory
5) Flash Philz recovery: fastboot flash recovery recovery.img the recovery.img is inside the arhive you must to place it in your fastboot folder
6) fastboot erase cache
7) Get the boot.img from inside the ROM and flash: fastboot flash boot boot.img take form ROM arhive and place in your fastboot directory
8) Enter recovery and flash ROM
Thant said:
The RUU it will work but you must to find 2.17.720.2 RUU I can find this RUU. If you update manualy the firmaware you must to install again Custom recovery after flash the firmware and it will be to be Philz recovery. After this you can flash the Viper X
This is for advanced USer only if you not feel advanced don't try please
CHARGE YOUR PHONE TO 100%
Download the rom and c
1) Make sure you have your Unlock_code.bin file.
Relock your device using fastboot: fastboot oem lock
Enter OEM flash mode using fastboot: fastboot oem rebootRUU
On your phone you will see a black screen with silver HTC written in the middle
Flash firmware: fastboot flash zip firmware.zip must be in your fastboot directory
(You need to do this immediately twice)
When you see a full green bar below, you are done.
3) Manually boot into fastboot on your device. Power off -> Power+ volume down
4) Unlock device: fastboot flash unlocktoken Unlock_code.bin must be in your fastboot directory
5) Flash Philz recovery[/URL]: fastboot flash recovery recovery.img the recovery.img is inside the arhive you must to place it in your fastboot folder
6) fastboot erase cache
7) Get the boot.img from inside the ROM and flash: fastboot flash boot boot.img take form ROM arhive and place in your fastboot directory
8) Enter recovery and flash ROM
Click to expand...
Click to collapse
Awesome guidance, if I find that RUU, everything goes back to stock? I will be able to download and install OTA updates? My phone becomes like.. a new one again? No need to unroot and everything?
Bijwa said:
Awesome guidance, if I find that RUU, everything goes back to stock? I will be able to download and install OTA updates? My phone becomes like.. a new one again? No need to unroot and everything?
Click to expand...
Click to collapse
yes if you find RUU everything will be stock but you can install nandroid backup with stock recovery and again you can receive the update. Read a little bit more before to start do anything to your phone. I see you are not advanced user and for this reason I write in RED the importhant line. Read more one two days and after this if you feal advanced start with flashing. The best way will be if you find the RUU for 2.17.720.2
Thant said:
yes if you find RUU everything will be stock but you can install nandroid backup with stock recovery and again you can receive the update. Read a little bit more before to start do anything to your phone. I see you are not advanced user and for this reason I write in RED the importhant line. Read more one two days and after this if you feal advanced start with flashing. The best way will be if you find the RUU for 2.17.720.2
Click to expand...
Click to collapse
Thank you so much, I'm already looking for the RUU but I can't find this sad! I will rep you, thanks for help.
Hi guys,
Please help !
I've bought a new phone, htc one x, from someone. barely had time to install few apps, and got this OTA update message.
Without thinking twice - i did it. But it seems that the phone was rooted ! and as I understand now - it's a big no-no .
I've tried to figure out from the forum what to do , but - all the answers seems to include fastboot and ADB, which in turn require
the drivers of the phone to be installed. But my phone is dead ! so I can' t do it.
I'm new to roms and all, and I really need your help .
How can I make my phone work again ? I don't care which ROM , custom or stock , just to make it work .
Any help will be appreciated.
Gena
You can access Fastboot? Hold POWER and VOLUMEN - (down)..?
Sent from my HTC One X using Tapatalk 2
big noob said:
You can access Fastboot? Hold POWER and VOLUMEN - (down)..?
Sent from my HTC One X using Tapatalk 2
Click to expand...
Click to collapse
Hi , yes, I can access the fast boot, but even trying to restore to factory defaults didn't help.
And I can't istall the fastboot on my pc since it needs to connect to a working phone in debug mode (if I understand correctly)
Google Fastboot files
And place them on your pc..for example
On desktop..
C:\Users\Name\Desktop\
and next step go in that directory via CMD typr this
cd C:\Users\Name\Desktop\Fastboot\
And type this
Fastboot getvar cid
Then you will se your CID
go this thread and follow steps to recover your phone
http://forum.xda-developers.com/showthread.php?t=1975140
Sent from my HTC One X using Tapatalk 2
big noob said:
Google Fastboot files
And place them on your pc..for example
On desktop..
C:\Users\Name\Desktop\
and next step go in that directory via CMD typr this
cd C:\Users\Name\Desktop\Fastboot\
And type this
Fastboot getvar cid
Then you will se your CID
go this thread and follow steps to recover your phone
http://forum.xda-developers.com/showthread.php?t=1975140
Sent from my HTC One X using Tapatalk 2
Click to expand...
Click to collapse
Thank you very much for your help.
I've did the steps as you say, and finally was able to "see" my phone in fastboot from PC.
but the CID I am getting is 11111111 , and there is no backup that matches it.
Can I overwrite it with some kind of rom ? I don't care to loose all the data, just to get a working phone.
Download clockwordmod recovery img file And flash it via Fastboot..
Fastboot flash recovery recoveryname.img
And then download this file:
Link!
And then access in recovery mount storage and copy that .zip file on your phone Clear and wipe everything except battery stats..And then flash that .zip file
genaddiy said:
Thank you very much for your help.
I've did the steps as you say, and finally was able to "see" my phone in fastboot from PC.
but the CID I am getting is 11111111 , and there is no backup that matches it.
Can I overwrite it with some kind of rom ? I don't care to loose all the data, just to get a working phone.
Click to expand...
Click to collapse
You are S-OFF you can install any RUU try with THIS ONE lock the bootloader and run the RUU as Administrator
post result from command fastboot getvar all and delete your S/N and IMEI from the info for any case
---------- Post added at 02:33 PM ---------- Previous post was at 02:32 PM ----------
big noob said:
Download clockwordmod recovery img file And flash it via Fastboot..
Fastboot flash recovery recoveryname.img
And then download this file:
Link!
And then access in recovery mount storage and copy that .zip file on your phone Clear and wipe everything except battery stats..And then flash that .zip file And try to flash it
Click to expand...
Click to collapse
He can't install OTA from recovery and you can't install OTA from recovery!!!!
Hi Thant, thank you for your help.
So you are saying that big noob's method won't work ?
I've downloaded the RUU, but I did not understand what you've meant by : "lock the bootloader" and when should I post the results of "fastboot getvar all" ? after I run the RUU , or before ?
You should post it before RUU..Well i tryed my method before and .zip flashed successfully..
And you can relock it with this command:
fastboot oem lock
Here's what I've got, no what should I do with it ?
>fastboot getvar all
(bootloader) version: 0.5a
(bootloader) version-bootloader: 1.12.0000
(bootloader) version-baseband: 2.1204.135.20
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main: 2.17.401.2
(bootloader) product: endeavoru
(bootloader) platform: HBOOT-T30S
(bootloader) modelid: PJ461****
(bootloader) cidnum: 11111111
(bootloader) battery-status: good
(bootloader) battery-voltage: 3821mV
(bootloader) devpower: 47
(bootloader) partition-layout: None
(bootloader) security: off
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: None
(bootloader) hbootpreupdate: 2
(bootloader) gencheckpt: 0
all: Done!
finished. total time: 0.830s
You can relock your bootloader download RUU and run it as administrator
I tried to relock , but it said phone is already locked.
Then I ran RUU and got the following error :
ERROR [159] - The ROM update utility cannot update your Android phone. Please get the correct ROM Update Utility and try again .
But what is the correct for me ? and where do I get it ?
genaddiy said:
I tried to relock , but it said phone is already locked.
Then I ran RUU and got the following error :
ERROR [159] - The ROM update utility cannot update your Android phone. Please get the correct ROM Update Utility and try again .
But what is the correct for me ? and where do I get it ?
Click to expand...
Click to collapse
Try this one
And when you in bootloader what is writen up RELOCKED and ENDEAVORU XE or ENDEAVORU PVT
98552432 231
In the bootloader it says :
*** LOCKED *****
ENDEAVORU XE SHIP S-OFF RL
genaddiy said:
In the bootloader it says :
*** LOCKED *****
ENDEAVORU XE SHIP S-OFF RL
Click to expand...
Click to collapse
ENDEAVORU XE have problems with update you must manually update the firmware and after this to install RUU or custom rom.
Download THIS OTA open the zip and extract firmware.zip to your fastboot folder after this do this
Type: fastboot oem rebootRUU and wait for device to reboot you will see HTC logo
Type: fastboot flash zip firmware.zip and wait for process to complete
Sometimes flashing for the first time doesn't work, so flash firmware.zip again just to make sure.
Type: fastboot flash zip firmware.zip and wait for process to complete
Type: fastboot reboot
Unlock your bootloader and flash custom recovery if you are going to use custom ROM.
I want to thank you for your patience with a noob like me
I did everything till the last line.
After flashboot reboot, my phone passed the first htc logo that it was stuck on , but now it's stuck on htc one screen (the one with beats audio logo at the bottom) .
Do I need to do the flash custom rom recovery ?
genaddiy said:
I want to thank you for your patience with a noob like me
I did everything till the last line.
After flashboot reboot, my phone passed the first htc logo that it was stuck on , but now it's stuck on htc one screen (the one with beats audio logo at the bottom) .
Do I need to do the flash custom rom recovery ?
Click to expand...
Click to collapse
yes now flash custom recovery philz 5.15.x mount usb storage copy custom rom to the phone install and flash the boot.img and you will have working rom sense or no sense. Now after flash the firmware what is your hboot version 1.39? If yes you are ready to go
ok , just to make sure I understand before I do it a screw something up :
"yes now flash custom recovery philz 5.15.x mount usb storage copy custom rom to the phone install and flash the boot.img and you will have working rom sense or no sense. Now after flash the firmware what is your hboot version 1.39? If yes you are ready to go"
my hboot version is indeed 1.39
so I d/l philz custom recovery .
no I should :
fastboot flash zip philz_touch_6.07.9-endeavoru.zip
then go to the custom recovery ? (how ? ? ? )
then d/l some custom rom (any recomendations ? just a good stable one, possibly stock)
then copy it to phone using fastboot
and then , from custom recovery flash it ?
I'm sorry for all these questions, but I'm afraid to touch the damn thing already ))))
Flash the recovery (its a img file NOT a zip, take out the img if its in the zip)
Fastboot flash recovery recoveryname.img
Fastboot erase cache
Enter the recovery by selecting FASTBOOT in the bootloader and then RECOVERY (navigate with the volume buttons and confirm with the power button)
Go to the mounts and storage menu and mount the sdcard as a mass storage disk (wait a few minutes until it pops up on the pc)
Copy the rom.zip to the sdcard. Take out the boot.img and flash it via fastboot
Fastboot flash boot boot.img
Fastboot erase cache
Enter recovery again and perform a full wipe
Factory reset
Wipe cache partition
Advanced-wipe dalvik cache
Mounts and storage-format cache, data and system
Install the rom.zip
Done !
Roms....just check the android dev section. Many roms to choose and read up for yourself. It's not that difficult ...maximus and arhd are very close to stock.
Thank you for the detailed reply !
When doing Fastboot flash recovery recoveryname.img I got the messege :
FAILED <remote : not allowed>
Is the problem that my phone is locked ? (written locked at the top of fastboot screen) tried to do fastboot oem unlock but getting "Command error !" .
I saw this solution : http://forum.cyanogenmod.com/topic/74316-a-solution-to-fastboot-flash-recovery-not-allowed-error/ , but I'm not sure it will fit my phone (as it talkes about a different one) and what is a PD98IMG.zip file ?
Hi !
I have a problem with my HTC DHD device. I unlocked it and rooted it a long time ago, using goldcard, installed Rom Manager, flashed the recovery, install CM...and all of a sudden, my phone shutted down, and couldn't stop rebooting, got the green HTC logo, and he reboot.
I had this problem a few month ago, i tried several things, that put my phone back in S-ON.
I actually got this :
Code:
c:\Fastboot>fastboot getvar all
INFOversion: 0.5
INFOversion-bootloader: 0.85.0024
INFOversion-baseband: 26.09.04.11_M2
INFOversion-cpld: None
INFOversion-microp: 0438
INFOversion-main: 2.50.405.2
INFOserialno: SH12ARX01979
INFOimei: 356299049586678
INFOproduct: ace
INFOplatform: HBOOT-7230
INFOmodelid: PD9810000
INFOcidnum: VODAP203
INFObattery-status: good
INFObattery-voltage: 3635mV
INFOpartition-layout: Generic
INFOsecurity: on
INFObuild-mode: SHIP
INFOboot-mode: FASTBOOT
INFOcommitno-bootloader: a3d4fa0f
INFOhbootpreupdate: 11
INFOgencheckpt: 0
INFOregion-id: 0
all: Done!
finished. total time: 0.008s
I can't access to recovery, and i can't boot on anything else than the HBOOT or FASTBOOT mode.
I tried to unlock from htc dev, but it says that i need to upgrade my HBOOT before using htcdev tool.
As i was back in S-ON mode, i tried severals RUU Roms.
As the getvar all says i'm actually running 2.50.405.2, so i tried to install a clean RUU using
RUU_Ace_Gingerbread_S_HTC_WWE_2.50.405.2_Radio_12.54.60.25_26.09.04.11_M2_release_199042_signed
( Got a french HTC DESIRE HD )
I'd like to flash a new recovery to make everything ok again. But i'm stuck, there is no ruu working, and i can't unlock bootloader, nor reinstall a recovery
everytime i try to flash something into any directory, i got this signature failed error.
Code:
c:\Fastboot>fastboot flash /sdcard PD98IMG.zip
sending '/sdcard' (261908 KB)... OKAY [ 43.281s]
writing '/sdcard'... INFOsignature checking...
FAILED (remote: signature verify fail)
finished. total time: 76.264s
Can someone help me ?
I might be wrong but I think you might need another ruu and a new goldcard
Sent from my HTC Desire HD using XDA Premium 4 mobile app
bondocel said:
I might be wrong but I think you might need another ruu and a new goldcard
Sent from my HTC Desire HD using XDA Premium 4 mobile app
Click to expand...
Click to collapse
I tried different RUU versions, all above the actual one or at least the same version.
The thing is that i can't actually put it back on its original configuration. CID is normal though, i can't find the original recovery, i'd like to flash it, i think it's the only thing that remains modified on the phone.
I had the exact same problem as you have when i bought the phone. AAHK was working back then and even with aahk the phone could not be fixed and the with the help of the devs on irc chat i managed to fix it
They told me that my phone was previously rooted and s-off but a strange RUU was flashed so they told me to flash cwm through fasboot and flash a custom rom.
Wich i did and it worked.
P.S. you might wanna try another sd card, this one might be fried ( faulty mem blocks)
bondocel said:
I had the exact same problem as you have when i bought the phone. AAHK was working back then and even with aahk the phone could not be fixed and the with the help of the devs on irc chat i managed to fix it
They told me that my phone was previously rooted and s-off but a strange RUU was flashed so they told me to flash cwm through fasboot and flash a custom rom.
Wich i did and it worked.
P.S. you might wanna try another sd card, this one might be fried ( faulty mem blocks)
Click to expand...
Click to collapse
Thanks for your answer, your previous problem exactly matches with mine. I'll try what you've said, the thing is that i'm actually not rooted, and S-ON, i can't use htcdev/unlockbootloader, because de version of my bootloader is too old ( i haven't used the phone for a while ) -
In fact :
- To solve my problem, like u said i have to flash CWM and a custom rom
- To flash a recovery, i need to unlock bootloader
- To unlock bootloader, i need to upgrade my bootloader
- To flash a ruu and upgrade my bootloader i need to have an original recovery
- Got a recovery problem i need another one, so let's flash CWM ( repeat everything )
Bruwno said:
Thanks for your answer, your previous problem exactly matches with mine. I'll try what you've said, the thing is that i'm actually not rooted, and S-ON, i can't use htcdev/unlockbootloader, because de version of my bootloader is too old ( i haven't used the phone for a while ) -
In fact :
- To solve my problem, like u said i have to flash CWM and a custom rom
- To flash a recovery, i need to unlock bootloader
- To unlock bootloader, i need to upgrade my bootloader
- To flash a ruu and upgrade my bootloader i need to have an original recovery
- Got a recovery problem i need another one, so let's flash CWM ( repeat everything )
Click to expand...
Click to collapse
http://shipped-roms.com/index.php?category=android&model=Ace
1) conect phone to pc, run instalation ruu
2) during instalation process find in win/temp folder file named rom.zip
3) copy this file into folder with adb and fastboot files
4) cancel instalation
5) in phone run bootloader than fastboot
6) run command prompt in folder with adb, fastboot and rom files, than type "fastboot oem rebootRUU"
7) wait a few minute until phone goes in ruu install mode
8) than from command prompt type "fastboot flash zip room.zip", if you get error repeat once again without exiting ruu install mode (some times is needed to do it twice)
9) when install finish type "fastboot reboot" and now phone should be repaired
You can do factory reset before and after.
Hi,
I have a HTC One X international version been in use for last 2 years. Just yesterday, I have unlocked the boot loader following instruction on HTCDev.com. Successfully rooted the phone following the instructions on onexroot.com. I have installed the ClockworkMod ROM on it. Until here things were fine. I have installed the ROM Manager from Android Market. Got the Super Admin. I have downloaded the Carbon ROM and Google Apps zip files to my phone. I have attempted install the Carbon Custom Rom on my phone, got the error status 7. this is where the problem started, by mistaken without taking the backup I have done the wipe data / factory reset. My phone is gone. It doesn't get identified in my Computer. Battery doesn't get charge. I have a clockworkmod recovery v5.8.2.7 on it.
Please please please help.. I did a sin..
bannyk.76 said:
Hi,
I have a HTC One X international version been in use for last 2 years. Just yesterday, I have unlocked the boot loader following instruction on HTCDev.com. Successfully rooted the phone following the instructions on onexroot.com. I have installed the ClockworkMod ROM on it. Until here things were fine. I have installed the ROM Manager from Android Market. Got the Super Admin. I have downloaded the Carbon ROM and Google Apps zip files to my phone. I have attempted install the Carbon Custom Rom on my phone, got the error status 7. this is where the problem started, by mistaken without taking the backup I have done the wipe data / factory reset. My phone is gone. It doesn't get identified in my Computer. Battery doesn't get charge. I have a clockworkmod recovery v5.8.2.7 on it.
Please please please help.. I did a sin..
Click to expand...
Click to collapse
First download the latest CWM 6.0.4.8 from CM11 thread or latest TWRP 2.7.1 or latest Philz recovery from original android section then install carbon rom. Carbon is based on 4.4.2 and you need latest recovery where support kitkat
EDIT: and something else you need to flash boot.img from rom.zip manually with the command fastboot flash boot boot.img , Rom Manager don't work on S-ON devices like ONE X
My phone shows battery level is too low to flash
bannyk.76 said:
Hi,
I have a HTC One X international version been in use for last 2 years. Just yesterday, I have unlocked the boot loader following instruction on HTCDev.com. Successfully rooted the phone following the instructions on onexroot.com. I have installed the ClockworkMod ROM on it. Until here things were fine. I have installed the ROM Manager from Android Market. Got the Super Admin. I have downloaded the Carbon ROM and Google Apps zip files to my phone. I have attempted install the Carbon Custom Rom on my phone, got the error status 7. this is where the problem started, by mistaken without taking the backup I have done the wipe data / factory reset. My phone is gone. It doesn't get identified in my Computer. Battery doesn't get charge. I have a clockworkmod recovery v5.8.2.7 on it.
Please please please help.. I did a sin..
Click to expand...
Click to collapse
Hi,
I am in Fastboot USB mode and the phone shows Battery level is too low to flash
I am unable to copy the files using fastboot commands. Also if I believe the charging levels are fluctuating and not consistent increasing.
Please advise.
Thanks a ton!!
bannyk.76 said:
Hi,
I am in Fastboot USB mode and the phone shows Battery level is too low to flash
I am unable to copy the files using fastboot commands. Also if I believe the charging levels are fluctuating and not consistent increasing.
Please advise.
Thanks a ton!!
Click to expand...
Click to collapse
first try to go in custom recovery and see if you can charge the phone from recovery if not Download THIS and connect the phone in fastboot and run the file chargeonex.bat
EDIT: no such rom like ClockworkMod ROM CWM is a recovery and you must to use command fastboot flash recovery nameofrecovery.img
Thanks a Ton
Your file chargeONEX really did a magic. my phone is charging now, slowly .. slowly ...
May I please request for detailed step by steps for what to be done next? I am getting a hope that my phone will be back to work.. Please advise.
bannyk.76 said:
Your file chargeONEX really did a magic. my phone is charging now, slowly .. slowly ...
May I please request for detailed step by steps for what to be done next? I am getting a hope that my phone will be back to work.. Please advise.
Click to expand...
Click to collapse
after you reach 3800mV flash custom recovery like Philz 5.15.9 and mount sd card copy what you need to the sd card after this if you whant to install 4.4.x you need to flash some of the latest recoverys on CWM,TWRP or Philz because Philz.5.15.9 will not work with the kitkat you can use it only to mount sd card and copy things to sd card. When you are done with the copy things flash the boot.img from rom.zip via fastboot and then flash the rom.zip from recovery and that is
Unable to boot in recovery with CWM 6.x
I have charged the battery for whole night and did a flash a CWM 5.8.4.0 and restarted the phone in recovery. After that I have flashed CWM 6.0 for KitKat and after that I am unable to restart the phone in Recovery mode. It stuck at the HTC Quietly brilliant screen.
Not sure where to start, I am totally confused with too many discussion forums with different suggestions. I am lost and my phone is in screwed up status.
What would you suggest as I am a novice person.
After flashing CWM 5.8.4.0 I am able to start phone in recovery, took back up, what is next? should I do a RUU... what is the funda of S-Off.
This is how my screen looks like now ..
**************Unlocked***********
ENDEAVORU PVT SHIP S-On RL
HBOOT - 1.73.0000
CPLD-NONE
MICROP-None
RADIO-5.1204.167.31
eMMC-boot mode : disabled
CPU-boot mode: disabled
HW Secure boot : enabled
C:\Development\All New>fastboot getvar all
INFOversion: 0.5a
INFOversion-bootloader: 1.73.0000
INFOversion-baseband: 5.1204.167.31
INFOversion-cpld: None
INFOversion-microp: None
INFOversion-main: 4.19.707.3
INFOserialno: SH23KW105277
INFOimei: 359188045391604
INFOproduct: endeavoru
INFOplatform: HBOOT-T30S
INFOmodelid: PJ4610000
INFOcidnum: HTC__044
INFObattery-status: good
INFObattery-voltage: 3610mV
INFOdevpower: 1
INFOpartition-layout: None
INFOsecurity: on
INFObuild-mode: SHIP
INFOboot-mode: FASTBOOT
INFOcommitno-bootloader: None
INFOhbootpreupdate: 2
INFOgencheckpt: 0
all: Done!
I think i am closer
Hot from the POT!!!
Able to mount the SD card in CWM v5.8.4.0 and copied the cm-11-20140613-NIGHTLY-endeavoru and gapps-kk-20140606-signed file and tried to "install zip from SDcard". both have failed with Status 7.
Any advise from here .. it seems I am close to getting back my phone....
bannyk.76 said:
Hot from the POT!!!
Able to mount the SD card in CWM v5.8.4.0 and copied the cm-11-20140613-NIGHTLY-endeavoru and gapps-kk-20140606-signed file and tried to "install zip from SDcard". both have failed with Status 7.
Any advise from here .. it seems I am close to getting back my phone....
Click to expand...
Click to collapse
Yes you must to be with the latest CWM 6.0.4.8 or TWRP2.7.x or Philz latest