Related
After a lot of reading, I collect the following, just for my own aid. I hope it will be proved useful to others.
I' ve just gathered all this information. All thanks goes to all those nice guys that spend time & put effort to find out all these procedures.
I'm just a bug.
(A few posts after this one, in the same thread, you can find the following guides:
How to Install NAND Android on HTC HD2 WITHOUT ClockWorkMod Recovery
&
FLASHING A NEW NAND ANDROID ROM OVER A PREVIOUS ONE (without clockwork mod)
&
FLASHING A NEW NAND ANDROID ROM OVER A PREVIOUS ONE (with clockwork mod)
At the end of this post you can find the neccessary files to download.
So here it is:
How to Install NAND Android on HTC HD2 with ClockWorkMod Recovery
(updated 25 May 2011)
Prerequisites
HSPL3 ~ SPL-2.08.HSPL or HSPL4 (Better use HSPL3. HSPL4 still has issues or errors on some devices, so use it at your own risk).
Radio that support 576 RAM (ex. radio ROM 2.15)
DFT MAGLDR Bootloader
ClockworkMod Recovery
It's advisable to copy the NAND Android ROM zip file to the root of your SD card, before start, because some people face problems to do this after doing the first steps of the process. If you don't do it then you can do it later using a card reader or doing this:
In MAGLDR choose option: #4 USB Mass Stg
or
In CWM choose option: mounts and storage option
Make sure that you have all the prerequisites installed.
STEPS:
A1: Install HSPL3
or
A2: Install HSPL4 (HSPL4 still has issues or errors on some devices, so use it at your own risk).
B: Install radio ROM 2.15
C: Install MAGLDR on HTC HD2
D: Install ClockworkMod Recovery (2 methods, choose the one you like)
E: Install NAND Android on HTC HD2 with ClockWorkMod Recovery
A1: Install HSPL3
Prerequisites
* Windows Mobile Device Center installed on Windows Vista / Windows 7 or
* ActiveSync installed on Windows XP
* You must have any SPL version from this list on your device:
o SPL 1.42.0000
o SPL 1.62.0000
o SPL 1.66.0000
o SPL 2.07.0000
o SPL 2.08.0000
o SPL 2.10.0000
(To check your SPL version, hold the Volume Down button and do a reset)
You should have this SPL version unless you are using the latest 3.14 ROM with SPL 3.03.0000. No worry, just downgrade your Windows Mobile ROM from v3.14 to v1.66 will do. Download HTC HD2 v1.66 ROM. Then downgrade your phone from SPL 3.03.0000 to SPL 1.42.000.
Step by Step Guide
1. Power off your phone.
2. Press volume down button (don’t let go) and power on your phone.
3. It will load into bootloader.
4. You should get ‘Red, Green, Blue and White’ screen with SPL-1.42.
5. Take off the battery.
6. Power on your phone.
7. Connect USB cable from PC to phone after Windows Mobile loaded.
8. Select ‘ActiveSync’ and click ‘Done’.
9. Open HSPL3_PKG.zip with 7-Zip.
10. Copy HSPL3_PKG.exe to desktop.
11. Execute HSPL3_PKG.
12. Follow onscreen instructions to install.
13. Click ‘Yes’ if User Access Control prompt up.
14. Bootloader will be loaded with USB status during starting of installation.
15. Select ’2.08.HSPL’ to install.
16. After installation, you should see ‘We hacked it!’ on your phone.
17. Click on ‘Yes’ and your phone should be rebooted and load into Windows Mobile.
18. Disconnect USB cable from phone.
19. To verify, power off your phone.
20. Press volume down button (don’t let go) and power on your phone.
21. It will load into bootloader.
22. You should get ‘Red, Green, Blue and White’ screen with SPL-2.08.HSPL.
23. That’s all.
OR
A2: Install HSPL4 (HSPL4 still has issues or errors on some devices, so use it at your own risk).
Prerequisites
* Windows Mobile Device Center installed on Windows Vista / Windows 7 or
* ActiveSync installed on Windows XP
* You must have any SPL version from this list on your device:
o SPL 1.42.0000
o SPL 1.62.0000
o SPL 1.66.0000
o SPL 2.07.0000
o SPL 2.08.0000
o SPL 2.10.0000
o SPL 3.03.0000 (for those using latest official HTC HD2 ROM v3.14)
(To check your SPL version, hold the Volume Down button and do a reset)
HSPL4 includes SPL-2.08.0000, SPL-2.08.HSPL, SPL-3.03.0000 and SPL-3.03.HSPL. The 3.03 SPL supports LEO1024.
You still need to use SPL-2.08.HSPL to use NAND Android and Windows Phone 7 and MAGLDR.
Make sure that you select the correct HSPL for your ROM installation.
Step by Step Guide
1. Power off your phone.
2. Press volume down button (don’t let go) and power on your phone.
3. It will load into bootloader.
4. You should get ‘Red, Green, Blue and White’ screen with SPL-1.42.
5. Take off the battery.
6. Power on your phone.
7. Connect USB cable from PC to phone after Windows Mobile loaded.
8. Select ‘ActiveSync’ and click ‘Done’.
9. Open HSPL4.zip with 7-Zip.
10. Copy HSPL4.exe to desktop.
11. Execute HSP4.
12. Follow onscreen instructions to install.
13. Click ‘Yes’ if User Access Control prompt up.
14. Bootloader will be loaded with USB status during starting of installation.
15. Select 2.08HSPL or 3.03HSPL. (This is to prevent people with 1024LEO's installing an incompatable version and bricking their device).
16. Click next
17. When its finished the phone should be rebooted and load into Windows Mobile.
18. Click ok to terminate program
19. Disconnect USB cable from phone.
20. To verify, power off your phone.
21. Press volume down button (don’t let go) and power on your phone.
22. It will load into bootloader.
23. You should get ‘Red, Green, Blue and White’ screen with SPL 2.08 or 3.03.
24. That’s all.
B: Install Custom Radio ROM
Prerequisites
* HSPL3 ~ SPL-2.08.HSPL
In order to flash custom radio ROM, you need to have HSPL3 installed on your HTC HD2. By the way, I used Radio Leo 2.15.50.14 on my guide. You can use it or any other HTC HD2 Radio ROM version.
HTC HD2 has 576 MB physical RAM but was reduced by software to 512 MB only. And custom Windows Mobile ROM + radio 2.07 or above can unlock it to be 576 MB again. Certain custom Windows Mobile ROM need higher radio version than your phone. And NAND Android requires it too. So you need to install custom radio ROM (if you don’t have the correct radio version).
Step by Step Guide
1. Power off your phone.
2. Press volume down button (don’t let go) and power on your phone.
3. It will load into bootloader.
4. You should get ‘Red, Green, Blue and White’ screen with SPL-2.08.HSPL.
5. Take off the battery.
6. Power on your phone.
7. I have R 2.06.51.07 at bottom of the screen with green HTC Logo.
8. Connect USB cable from PC to phone after Windows Mobile loaded.
9. Select ‘ActiveSync’ and click ‘Done’.
10. Open Radio Leo 2.15.50.14.rar with 7-Zip.
11. Copy CustomRUU.exe and RUU_signed.nbh to desktop.
12. Execute CustomRUU.
13. Click ‘Yes’ if User Access Control prompt up.
14. Follow onscreen instructions to install.
15. Bootloader will be loaded with USB status during starting of installation. (~10 minutes)
16. Phone will be rebooted after installation finished.
17. You should have R 2.15.50.14 at bottom of the screen with green HTC Logo.
18. Disconnect USB cable from phone.
19. That’s all.
C: Install MAGLDR
In order to install NAND Android on HTC HD2, you must install DFT MAGLDR Bootloader first. And the good news ~ both LEO512 and LEO1024 are supported. This means US T-Mobile HD2, Europe, Asia and the rest of the world’s HTC HD2 are supported.
Note – by installing MAGLDR, you cannot boot into Windows Mobile anymore. So everything on your phone is gone…
Prerequisites
* HSPL3 ~ SPL-2.08.HSPL
* Radio that support 576 RAM
No worry, Android on NAND is working. That’s the reason we install DFT MAGLDR Bootloader on our HTC HD2, right? And we will be able to load the latest Windows Phone version (if we are crazy...) when the ROM comes out. Okay, let’s get started. If you don’t have HSPL3, please install it first. And aslo install radio ROM 2.15.
Step by Step Guide
1. Power off your phone.
2. Press volume down button (don’t let go) and power on your phone.
3. It will load into bootloader.
4. You should get ‘Red, Green, Blue and White’ screen with SPL-2.08.HSPL.
5. Take off the battery.
6. Power on your phone.
7. You should have R 2.15.50.14 at bottom of the screen with green HTC Logo.
8. Connect USB cable from PC to phone after Windows Mobile loaded.
9. Select ‘ActiveSync’ and click ‘Done’.
10. Open DFT_LEO_MAGLDR113.rar with 7-Zip.
11. Copy MAGLDR113 folder to desktop.
12. Enter MAGLDR113 folder.
13. Execute ROMUpdateUtility.
14. Click ‘Yes’ if User Access Control prompt up.
15. Follow onscreen instructions to install.
16. Bootloader will be loaded with USB status during starting of installation.
17. Phone will be rebooted after installation finished.
18. DFT MAGLDR Bootloader will be loaded then.
19. Disconnect USB cable from phone.
20. That’s all.
D: How to Install ClockworkMod Recovery on HTC HD2
Prerequisites
HSPL3 ~ SPL-2.08.HSPL
Radio that support 576 RAM
DFT MAGLDR Bootloader
Please make sure that you have all the prerequisites installed.
If you don’t have HSPL3, please install it.
Also install radio ROM 2.1.
Finally, install DFT MAGLDR Bootloader.
There are two methods. They are both working. Choose the one you like.
Method 1
Step by Step Guide
1. Power on your phone and don’t let go power button.
2. DFT MAGLDR Bootloader will be loaded.
3. Use volume down button to go down to 4. USB MassStg.
4. Then press call button to enter USB Mass Storage mode.
5. Connect USB cable from PC to phone.
6. At PC, open Removable Disk (SD card storage).
7. Create a temp folder.
8. Open ClockworkMod-Recovery V.1.2 with 7-Zip.
9. Copy everything to temp folder.
10. Enter temp folder.
11. Enter copy_to_sd_root folder.
12. Copy initrd.gz and zImage files to SD card root level.
13. Then disconnect USB cable from phone.
14. Press power button to go back.
15. Use volume down button to go to 11. Reset.
16. Then press call button.
17. Press power button and don’t let go.
18. DFT MAGLDR Bootloader will be loaded.
19. Use volume down button to go down to 5. USB Flasher.
20. Then press call button to load Android Flasher mode.
21. Connect USB cable from PC to phone.
22. At PC, right click on DAF and select ‘Run as administrator’.
23. Click ‘Yes’ if User Access Control prompt up.
24. Follow onscreen instructions to install.
25. Phone will be rebooted after installation finished.
26. DFT MAGLDR Bootloader will be loaded then.
27. Disconnect USB cable from phone.
28. Press call button to load 2. Boot AD SD.
29. ClockworkMod Recovery will be loaded then.
30. That’s all.
Alternatively, there exist a faster method, from MAGLDR NAND Boot. It goes like this:
Method 2
Step by Step Guide
1. Download recovery with partition size for the type of rom you plan on using (150, 250 or 400) (to choose, see the guide at the bottom of this post).
2. Extract downloaded file
3. Go into MAGLDR and choose 5. USB Flasher.
3. On PC run DAF.exe and follow instructions
4. After installation completed and phone reboots, hold power key and select 8. AD Recovery
5. The phone will load into Recovery
6. That’s all.
E: Install NAND Android on HTC HD2 with ClockWorkMod Recovery
Install NAND Android on HTC HD2 with ClockworkMod Recovery is the 2nd method to have NAND Android on HTC HD2. And this can be done by using SD card only without PC. Just download the zip ROM to your SD card and you are ready to go. In addition, you can backup and restore ROM using Nandroid. Or you can try the 1st method through DFT MAGLDR Bootloader which requires PC with USB connection.
Prerequisites
HSPL3 ~ SPL-2.08.HSPL
Radio that support 576 RAM
DFT MAGLDR Bootloader
ClockworkMod Recovery
Having NAND Android on HTC HD2 is not a simple task like ABC. But it is not mission impossible too. Just follow these guides to get all the prerequisites installed. Please install HSPL3. Install Custom Radio ROM 2.15. Then, install DFT MAGLDR Bootloader. Finally, install ClockworkMod Recovery. Wow… Lot of steps but worth it. Trust me…
Step by Step Guide
1. Power on your phone and don’t let go power button.
2. DFT MAGLDR Bootloader will be loaded.
3. Use volume down button to go down to 4. USB MassStg.
4. Then press call button to enter USB Mass Storage mode.
5. Connect USB cable from PC to phone.
6. At PC, open Removable Disk (SD card storage).
7. Open your favorite ROM (ex. JawsMIUIrec1.0.7z) with 7-Zip.
8. Copy .data folder and ex. JawsNandRec1.1.zip to SD card root level.
9. There should be config and data files in .data folder.
10. Then disconnect USB cable from phone.
11. Press power button to go back.
12. Use volume up button to go up to 12. PowerDown.
13. Then press call button.
14. Power on phone and don’t let go power button.
15. DFT MAGLDR Bootloader will be loaded.
16. Press call button to load 2. Boot AD SD.
17. ClockworkMod Recovery will be loaded then.
18. Use volume down button to go down to ‘install zip from sdcard’.
19. Then press call button.
20. Use volume down button to go down to ‘choose zip from sdcard’.
21. Then press call button.
22. You should see ex. JawsNandRec1.1.zip.
23. Then press call button to select it.
24. Use volume down button to go down to ‘Yes – ex. JawsNandRec1.1.zip’.
25. Press call button and installation will be started.
26. When you see ‘Install from sdcard complete’, press power button.
27. Press call button to select ‘reboot system now’.
28. Phone will be rebooted and enter NAND Android automatically.
29. Follow onscreen instructions to setup Android settings.
30. That’s all.
Good Luck
Just below are the files where you can download directly, exept for the radio, that you can get it here: Radio Leo 2.15.50.14
(If you are going for the 2nd method of ClockWorkMode, then depending on what type of roms you plan on using, you should download the partition size based on the following:
150MB Partition - For bare roms including CyanogenMod, AOSP, and MiUI
[*]250MB Partition - For Standard sense roms including Desire and EVo based ROMs, can also be used for some squashed HD builds
[*]400MB Partition - For Larger roms including unsquashed Desire HD and Z roms, ROMs REQUIRE data2sd for EU HD2 with 512MB NAND)
Well played sir and thanks for putting in the time to write this guide. Perhaps a passing mod would care to sticky this, either here or in a HD2 forum?
BTW, have an E-cookie for what is probably the best 1st post i've ever seen here
Totally agree. Even though I personally don't need this guide, I've still thanked you because I appreciate the time and effort you've put in, and that's just a brilliant 1st post!
Welcome to xda mate
+1 ....awesome Ist post, very useful for many.
Great guide!
Dear friend Gn,
thank you for your guide it is very detailed and precise but despite that fact
my ignorance(or stupidity) did't let me make the work. My mem is still 448mb, i thought after making the first two steps i'll had 576 of mem but it didn't work. At the first place i had 1.44 rom then i have change it in 1.66 with radio 2.15 but all that after installing Hspl.oops!!.
So now i have no idea how to proceed and put the android nand on. Can you help me please?
Thank you in advance
I think by memory he meant ROM not RAM
Since the first guide was useful to some people, I'm posting another one: How to Install NAND Android on HTC HD2 without ClockWorkMod Recovery. The first three steps are the same. All this stuff is not mine. I've just gathered other peoples postings. So all thanks shloud go to them. I'm just a bug.
How to Install NAND Android on HTC HD2 WITHOUT ClockWorkMod Recovery(updated 12 March 2011)
Prerequisites
HSPL3 ~ SPL-2.08.HSPL or HSPL4
Radio that support 576 RAM (ex. radio ROM 2.15)
DFT MAGLDR Bootloader
Make sure that you have all the prerequisites installed.
STEPS:
A1: Install HSPL3
or
A2: Install HSPL4
B: Install radio ROM 2.15
C: Install MAGLDR on HTC HD2
D: Install NAND Android on HTC HD2
A1: Install HSPL3
Prerequisites
* Windows Mobile Device Center installed on Windows Vista / Windows 7 or
* ActiveSync installed on Windows XP
* You must have any SPL version from this list on your device:
o SPL 1.42.0000
o SPL 1.62.0000
o SPL 1.66.0000
o SPL 2.07.0000
o SPL 2.08.0000
o SPL 2.10.0000
(To check your SPL version, hold the Volume Down button and do a reset)
You should have this SPL version unless you are using the latest 3.14 ROM with SPL 3.03.0000. No worry, just downgrade your Windows Mobile ROM from v3.14 to v1.66 will do. Download HTC HD2 v1.66 ROM. Then downgrade your phone from SPL 3.03.0000 to SPL 1.42.000.
Step by Step Guide
1. Power off your phone.
2. Press volume down button (don’t let go) and power on your phone.
3. It will load into bootloader.
4. You should get ‘Red, Green, Blue and White’ screen with SPL-1.42.
5. Take off the battery.
6. Power on your phone.
7. Connect USB cable from PC to phone after Windows Mobile loaded.
8. Select ‘ActiveSync’ and click ‘Done’.
9. Open HSPL3_PKG.zip with 7-Zip.
10. Copy HSPL3_PKG.exe to desktop.
11. Execute HSPL3_PKG.
12. Follow onscreen instructions to install.
13. Click ‘Yes’ if User Access Control prompt up.
14. Bootloader will be loaded with USB status during starting of installation.
15. Select ’2.08.HSPL’ to install.
16. After installation, you should see ‘We hacked it!’ on your phone.
17. Click on ‘Yes’ and your phone should be rebooted and load into Windows Mobile.
18. Disconnect USB cable from phone.
19. To verify, power off your phone.
20. Press volume down button (don’t let go) and power on your phone.
21. It will load into bootloader.
22. You should get ‘Red, Green, Blue and White’ screen with SPL-2.08.HSPL.
23. That’s all.
OR
A2: Install HSPL4
Prerequisites
* Windows Mobile Device Center installed on Windows Vista / Windows 7 or
* ActiveSync installed on Windows XP
* You must have any SPL version from this list on your device:
o SPL 1.42.0000
o SPL 1.62.0000
o SPL 1.66.0000
o SPL 2.07.0000
o SPL 2.08.0000
o SPL 2.10.0000
o SPL 3.03.0000 (for those using latest official HTC HD2 ROM v3.14)
(To check your SPL version, hold the Volume Down button and do a reset)
HSPL4 includes SPL-2.08.0000, SPL-2.08.HSPL, SPL-3.03.0000 and SPL-3.03.HSPL. The 3.03 SPL supports LEO1024.
You still need to use SPL-2.08.HSPL to use NAND Android and Windows Phone 7 and MAGLDR.
Make sure that you select the correct HSPL for your ROM installation.
Step by Step Guide
1. Power off your phone.
2. Press volume down button (don’t let go) and power on your phone.
3. It will load into bootloader.
4. You should get ‘Red, Green, Blue and White’ screen with SPL-1.42.
5. Take off the battery.
6. Power on your phone.
7. Connect USB cable from PC to phone after Windows Mobile loaded.
8. Select ‘ActiveSync’ and click ‘Done’.
9. Open HSPL4.zip with 7-Zip.
10. Copy HSPL4.exe to desktop.
11. Execute HSP4.
12. Follow onscreen instructions to install.
13. Click ‘Yes’ if User Access Control prompt up.
14. Bootloader will be loaded with USB status during starting of installation.
15. Select 2.08HSPL or 3.03HSPL. (This is to prevent people with 1024LEO's installing an incompatable version and bricking their device).
16. Click next
17. When its finished the phone should be rebooted and load into Windows Mobile.
18. Click ok to terminate program
19. Disconnect USB cable from phone.
20. To verify, power off your phone.
21. Press volume down button (don’t let go) and power on your phone.
22. It will load into bootloader.
23. You should get ‘Red, Green, Blue and White’ screen with SPL 2.08 or 3.03.
24. That’s all.
B: Install Custom Radio ROM
Prerequisites
* HSPL3 ~ SPL-2.08.HSPL
In order to flash custom radio ROM, you need to have HSPL3 installed on your HTC HD2. By the way, I used Radio Leo 2.15.50.14 on my guide. You can use it or any other HTC HD2 Radio ROM version.
HTC HD2 has 576 MB physical RAM but was reduced by software to 512 MB only. And custom Windows Mobile ROM + radio 2.07 or above can unlock it to be 576 MB again. Certain custom Windows Mobile ROM need higher radio version than your phone. And NAND Android requires it too. So you need to install custom radio ROM (if you don’t have the correct radio version).
Step by Step Guide
1. Power off your phone.
2. Press volume down button (don’t let go) and power on your phone.
3. It will load into bootloader.
4. You should get ‘Red, Green, Blue and White’ screen with SPL-2.08.HSPL.
5. Take off the battery.
6. Power on your phone.
7. I have R 2.06.51.07 at bottom of the screen with green HTC Logo.
8. Connect USB cable from PC to phone after Windows Mobile loaded.
9. Select ‘ActiveSync’ and click ‘Done’.
10. Open Radio Leo 2.15.50.14.rar with 7-Zip.
11. Copy CustomRUU.exe and RUU_signed.nbh to desktop.
12. Execute CustomRUU.
13. Click ‘Yes’ if User Access Control prompt up.
14. Follow onscreen instructions to install.
15. Bootloader will be loaded with USB status during starting of installation. (~10 minutes)
16. Phone will be rebooted after installation finished.
17. You should have R 2.15.50.14 at bottom of the screen with green HTC Logo.
18. Disconnect USB cable from phone.
19. That’s all.
C: Install MAGLDR
In order to install NAND Android on HTC HD2, you must install DFT MAGLDR Bootloader first. And the good news ~ both LEO512 and LEO1024 are supported. This means US T-Mobile HD2, Europe, Asia and the rest of the world’s HTC HD2 are supported.
Note – by installing MAGLDR, you cannot boot into Windows Mobile anymore. So everything on your phone is gone…
Prerequisites
* HSPL3 ~ SPL-2.08.HSPL
* Radio that support 576 RAM
No worry, Android on NAND is working. That’s the reason we install DFT MAGLDR Bootloader on our HTC HD2, right? And we will be able to load a Windows Phone version when a new ROM comes out. Okay, let’s get started. If you don’t have HSPL3, please install it and also install radio ROM 2.15.
Step by Step Guide
1. Power off your phone.
2. Press volume down button (don’t let go) and power on your phone.
3. It will load into bootloader.
4. You should get ‘Red, Green, Blue and White’ screen with SPL-2.08.HSPL.
5. Take off the battery.
6. Power on your phone.
7. You should have R 2.15.50.14 at bottom of the screen with green HTC Logo.
8. Connect USB cable from PC to phone after Windows Mobile loaded.
9. Select ‘ActiveSync’ and click ‘Done’.
10. Open DFT_LEO_MAGLDR113.rar with 7-Zip.
11. Copy MAGLDR113 folder to desktop.
12. Enter MAGLDR113 folder.
13. Execute ROMUpdateUtility.
14. Click ‘Yes’ if User Access Control prompt up.
15. Follow onscreen instructions to install.
16. Bootloader will be loaded with USB status during starting of installation.
17. Phone will be rebooted after installation finished.
18. DFT MAGLDR Bootloader will be loaded then.
19. Disconnect USB cable from phone.
20. That’s all.
D: Install NAND Android
Prerequisites
* HSPL3 ~ SPL-2.08.HSPL
* Radio that support 576 RAM
* DFT MAGLDR Bootloader
Make sure that you have all the prerequisites installed.
Step by Step Guide
1. Power on your phone.
2. DFT MAGLDR Bootloader will be loaded.
3. Use volume down button to go down to 5. USB Flasher.
4. Then press call button to load Android Flasher mode.
5. Connect USB cable from PC to phone.
6. Open your favorite ROM (ex. DFT_LEO_NAND_Android.rar) with 7-Zip.
7. Copy DFT_Android folder to desktop.
8. Enter DFT_Android folder.
9. Execute DAF.
10. Follow onscreen instructions to install.
11. Click ‘Yes’ if User Access Control prompt up.
12. Phone will be rebooted after installation finished.
Maybe the next steps are not obligatory, depending on the ROM you are going to install. In my case, I didn't have to follow the rest of the process, because the ROM I've used, has done the job itself and my phone was ready to work. (I've used CleanDroid and I had PERFCET results. Very light, clean and stable ROM. I've installed 30-40 apps and still is stable, alive and kicking.)
13. DFT MAGLDR Bootloader will be loaded then.
14. Use volume down button to go down to 3. Boot AD NAND.
15. Then press call button to load NAND Android.
16. Disconnect USB cable from phone.
17. Follow onscreen instructions to setup Android settings.
18. That’s all.
Alsomaybe the next steps are not obligatory.
To make auto boot to NAND Android.
1. Restart your phone.
2. Load to DFT MAGLDR Bootloader
3. Use volume up button to go up to 10. Services.
4. Then press call button to load Services Menu.
5. Then press call button again to enter AutoBoot settings.
6. Then press call button again to enter Boot source settings.
7. Select 3. Android from NAND with call button.
8. Use volume up button to go up to 10. Services again.
9. Then press call button to load Services Menu.
10. Then press call button again to enter AutoBoot settings.
11. Select 2. AlwaysMenu with call button.
12. Press power on/off button to select NO at Show boot menu always at boot?
13. Use volume up button to go up to 11. Reset.
14. Phone will be rebooted and enter NAND Android automatically.
15. That’s all.
Good Luck
install fresh Android ROM over dual boot hd2
I've set up dual boot to android and WP7 on my HTC HD2. I now wish to go back to only ANdroid on my phone. What are the steps for that. As my SD Card is partitioned will the new android rom be installed on just the NAND portion?
I need to know to what type of filesystem should I format my SD card so that i can install a fresh ROM.DO i need to go back to stock WM6.5 to install this.
Hi aditya_r12
Here's my newbie answer.
I think you can forget the sd card temporarily (remove it if you want),
flash a windows sytem (or just leave the existing win7) and then follow one of the above methods (the easier is the non clockwork mod), and you will be back to a nand android-only phone. After you can mount back your card with one or two partitions, or you can reparticion it or whatever.
I hope an experienced member, will also answer to you, since I'm an absolute ignorant newbie, which was lucky enough to manage to flash a perfeclty functioning android hd2, from scratch (thanks to the instructions of these nice people in this forum).
Good luck
Ho. Thanks for the reply. I finally got to installing nand android using clockwork mod. I used tadk29 to clear everything. Now I'd really like to know how to increase my internal storage
Its only some 250 MB right now. Is it possible to make it think that the storage extends to the SD card
gunjahman said:
Hi aditya_r12
Here's my newbie answer.
I think you can forget the sd card temporarily (remove it if you want),
flash a windows sytem (or just leave the existing win7) and then follow one of the above methods (the easier is the non clockwork mod), and you will be back to a nand android-only phone. After you can mount back your card with one or two partitions, or you can reparticion it or whatever.
I hope an experienced member, will also answer to you, since I'm an absolute ignorant newbie, which was lucky enough to manage to flash a perfeclty functioning android hd2, from scratch (thanks to the instructions of these nice people in this forum).
Good luck
Click to expand...
Click to collapse
Thank You~
I really need this faq but I thought there were newer versions of CWM that did not requier the "move to SD" files? Am I just totlly lost or is the faq older than those files?
Thank you for this guide. It will be very helpful for people like me (who don't read much unless encounter an issue) if download links will be available here also. So, it'll be a one stop shop guide..
I'm about to input the download links and the links for some video guides, as soon as I have the permission from the forum op.
Flashing a new nand android rom over a previous one
FLASHING A NEW NAND ANDROID ROM OVER A PREVIOUS ONE
(without clockwork mod)
Once you have flashed Magldr to your device you do not have to go through the whole process again if you want to flash a new NAND Android Rom:
1. Turn your phone off
2. Restart your phone by holding down the 'Power' button and keep holding it down until the Magldr Menu appears
3. Press the 'Volume Down' button to goto Option 4: USB Flasher and press the 'Call' button (far left of the 5 hardware buttons at the bottom)
4. Browse to the folder you extracted your NAND Android Rom files to on your pc, right click on Run DAF.exe (or install.exe if Daf.exe isnt listed) and select Run as Administrator (if using Windows Vista or Windows 7)
5. Read ALL the text and then select 'Next'
6. Read the information and select 'Next'
7. The installer will now detect USB and then flash your Android Rom to NAND
8. When flashing is complete your phone will Reboot and proceed to boot Android from NAND
That's all
Good Luck
Im a Evo user and trying to install Android on a buddys HD2. I am stuck at the pink stick together screen after step B completed and is trrying to redoot.. I dont think it wants to boot. Any ideas?
Apparently there are quite a few other benefits of installing CWM such as installing mods to your ROM. Unfortunately, I chose to install my present (and very stable) ROM without using CWM. Is there anyway to install CWM without losing my existing ROM?
gunjahman said:
After a lot of reading, I collect the following, just for my own aid. I hope it will be proved useful to others.
....
D: How to Install ClockworkMod Recovery on HTC HD2
Click to expand...
Click to collapse
thanks, i will give it a try
Perfect guide, thanks a lot. I completed the steps within an hour!
Well, this is something that has been asked to me a lot. And to be honest, i was trying to get the answer to these question a few weeks ago. But i have finally prepared a step by step guide on both topic, Running Any Android Rom on cLK and Switching to cLK from MAGLDR. But first, lets see what cLK has to offer compared to MAGLDR. (It doesn't necessarily mean that cLK is better than MAGLDR or MAGLDR is better than cLK)
1) cLK is open source unlike MAGLDR, which means we can modify anything we want and make it better. And there will likely be a lot more updates than MAGLDR because everyone can use the source code and release a new version (for example: arif-ali's cLK 1.4.0.1)
2) cLK has native android like functions with fastboot.
3) cLK does not show any screen between the kernel and spl (the go go go screen), so it feels more like native android.
4) cLK supports fastboot mode (more native android feel)
5) cLK supports use of rom manager
These are just some things i figured out while using cLK, but there are a lots of other things that i have forgot to mention. This doesnt necessarily mean that you should use clk, magldr has a lots of other features that are better than clk like sd boot, windows support, boot menu, tetris D ?) and few more. But if you feel like switching to clk, then this guide should help you out.
Post #2 - Running any MAGLDR rom on cLK
Post #3 - Changing from MAGLDR to cLK without losing any data.
Note: I dont take any responsibility for any damage caused by the use of this guide/tools. Use it at your own risk
Credits:
CharnSingh for improved kernel.
arif-ali for making an flashable zip with beta ril wrapper
Everyone else i forgot
Click to expand...
Click to collapse
!!Warning!! You are warned not to use cLK at any cost if you are a tetris fan! (JK)
!!Warning!! Some sense roms using RAM method might not work using this method!
Not finding a lots of roms for cLK might be one of the reasons why you havent switched to cLK yet. But not anymore, since there is a way to run most magldr roms on cLK. So lets start it step by step:
Running any MAGLDR rom on cLK
1) Go to this link and download HD2 Toolkit i made for making easier to download stuff.
2) Extract the zip file to some folder, and open HD2_Installer.exe
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
3) Click Wipe (Task29) Button.
4) A new window will open. Carefully follow the steps given on the tool. And you will come back to HD2 Toolkit after the tool completes its work.
System Partition Size:
120 MB For AOSP Roms
150 MB For Cyanogenmod/Miui Roms
450 MB For Sense Roms
(These are just average sizes for most roms, if the rom maker has specified a partition size, flash that.)
Click to expand...
Click to collapse
5) Choose cLK Repartition, Choose System Partition Size, Choose Cache Size and press Repartition Button.
6) Press OK on next screen.
7) A new window will open again. Carefully follow the steps given on the tool. And you will come back to HD2 Toolkit after the tool completes its work.
8) You phone will reboot an get stuck on a screen with some text.
9) Choose cLK Install Recovery and press Update.
10) Click yes on next Window.
11) A new command window will open, follow instructions there and you will come back to HD2 Installer after it completes. When your phone reboots, keep holding the home button. Your phone will get into recovery if you do it properly.
12) Download this file and your favourite rom.
13) Choose "mounts and storage" on recovery and choose "USB Mount" after that. Then copy both of those files into your sd card on your computer. Unmount after you finish copying. Press back button on your phone to go back to main screen.
14) Choose "install zip from sdcard" option and isntall the rom first.
15) Install the other downloaded file now (Credit goes to arif-ali for the file, dont forget to thank him )
16) Reboot! And you are done
I hope this helped. Any suggestions/comments welcome.
!!Warning!! Oops no warnings for this post
I am pretty sure that lot of you are waiting for someone to post a tutorial on how to change from MAGLDR to cLK without losing rom or anything. So here you go.
Changing from MAGLDR to cLK without losing any data.
So, without talking, lets start the job
1) Go to this link and download HD2 Toolkit i made for making easier to download stuff.
2) Extract the zip file to some folder, and open HD2_Installer.exe
3) Power off your phone, and hold power button till you get into MAGLDR menu. Then choose "AD Recovery" and go to recovery. Backup your current rom by going to "backup and restore" -> "backup". Make sure your sd card is not full.
4) Follow the instructions #3 to #11 from second post.
ksubedi said:
3) Click Wipe (Task29) Button.
4) A new window will open. Carefully follow the steps given on the tool. And you will come back to HD2 Toolkit after the tool completes its work.
System Partition Size:
120 MB For AOSP Roms
150 MB For Cyanogenmod/Miui Roms
450 MB For Sense Roms
(These are just average sizes for most roms, if the rom maker has specified a partition size, flash that.)
Click to expand...
Click to collapse
5) Choose cLK Repartition, Choose System Partition Size, Choose Cache Size and press Repartition Button.
6) Press OK on next screen.
7) A new window will open again. Carefully follow the steps given on the tool. And you will come back to HD2 Toolkit after the tool completes its work.
8) You phone will reboot an get stuck on a screen with some text.
9) Choose cLK Install Recovery and press Update.
10) Click yes on next Window.
11) A new command window will open, follow instructions there and you will come back to HD2 Installer after it completes. When your phone reboots, keep holding the home button. Your phone will get into recovery if you do it properly.
.
Click to expand...
Click to collapse
5) Download this file .
6) Choose "mounts and storage" on recovery and choose "USB Mount" after that. Then copy both of those files into your sd card on your computer. Unmount after you finish copying. Press back button on your phone to go back to main screen.
7) Go to "backup and restore" -> restore and choose your backup file and restore.
8) Then install the other file you copied to your sd card. (Credit goes to arif-ali for the file, dont forget to thank him )
9) Reboot, and everything should work like it used to work before.
Hope this helps as well. Have a great day guys.
Ran out of my Thanks quota for the day, but, ksubedi - THANKS!!! I was looking for just this!
ph03n!x said:
Ran out of my Thanks quota for the day, but, ksubedi - THANKS!!! I was looking for just this!
Click to expand...
Click to collapse
excelent , excelent, thx for all.
I've got one question - why it is used 200MB partition when we do "CLK repartition ", and after that 150MB when we do "CLK Install recovery"? And the second part of the question is can we use other system size and what does "Install CLK" button do?
ksubedi said:
!!Warning!! Oops no warnings for this post
I am pretty sure that lot of you are waiting for someone to post a tutorial on how to change from MAGLDR to cLK without losing rom or anything. So here you go.
Changing from MAGLDR to cLK without losing any data.
So, without talking, lets start the job
1) Go to this link and download HD2 Toolkit i made for making easier to download stuff.
2) Extract the zip file to some folder, and open HD2_Installer.exe
3) Power off your phone, and hold power button till you get into MAGLDR menu. Then choose "AD Recovery" and go to recovery. Backup your current rom by going to "backup and restore" -> "backup". Make sure your sd card is not full.
4) Follow the instructions #3 to #11 from second post.
5) Download this file .
6) Choose "mounts and storage" on recovery and choose "USB Mount" after that. Then copy both of those files into your sd card on your computer. Unmount after you finish copying. Press back button on your phone to go back to main screen.
7) Go to "backup and restore" -> restore and choose your backup file and restore.
8) Then install the other file you copied to your sd card. (Credit goes to arif-ali for the file, dont forget to thank him )
9) Reboot, and everything should work like it used to work before.
Hope this helps as well. Have a great day guys.
Click to expand...
Click to collapse
i stuck on step 11) A new command window will open, follow instructions there and you will come back to HD2 Installer after it completes. When your phone reboots, keep holding the home button. Your phone will get into recovery if you do it properly. ( i can't power it off using my phone's power key, then i take the battery off from my phone then plug it back, is it any wrong?
ra6o74 said:
I've got one question - why it is used 200MB partition when we do "CLK repartition ", and after that 150MB when we do "CLK Install recovery"? And the second part of the question is can we use other system size and what does "Install CLK" button do?
Click to expand...
Click to collapse
well , that was an example , you must use system size told by your rom developer.
Option 2 - 3 - 4 are the same?
2) cLK has native android like functions with fastboot.
3) cLK does not show any screen between the kernel and spl (the go go go screen), so it feels more like native android.
4) cLK supports fastboot mode (more native android feel)
Click to expand...
Click to collapse
Step 11 is not working for me, too. The cmd stucks at " <Waiting for device> "!!!
What to do now?
It doesn't work with CoreDroid 1.6 on my HD2.
Perhaps need clk at 390.
hanbam said:
Step 11 is not working for me, too. The cmd stucks at " <Waiting for device> "!!!
What to do now?
Click to expand...
Click to collapse
Hanbam, i had the same problem. I fixed it by installing the Google USB Driver. All instructions and links are here
http://developer.android.com/sdk/win-usb.html
Perhaps something to add to a FAQ?
Greets
Ciss
Tried my luck with CMYLXGO's Stock Desire HD (v1.1.17) (a Sense ROM), and got into the Android boot logo loop. I also tried Tytung R10 ppp update (just a blind shot) instead of the charan_05152011_cLK_ppp_cache.zip file attached in the second post - still no go.
I am using RAFDROID HD 4.0.2! After changing to clk, I can install recovery and do a restore, but when it reboot, it just stuck at the white htc page.
A quick question,what's the file that we download at step 12,what's the use of it? and can i flash my rom in CWM without it?!
It's for improve stability on ppp mode with clk
actually I can make any MAGLDR rom boot by CLK including sense rom, but one problem I cannot solved. that is the wifi not working.
steps are as follows:
1.flash Task 29 with Radio 2.15.50.14
2.flash clk 1.4.0.1
3.flash cLK_Rcovery 3.2.0.0 (size depending on rom's requirement)
4.flash ROM（zip package）
5.flash charan_05152011_cLK_ppp_cache.zip
6.flash Kernel initrd.gz and zImage（take from Zip Rom）
@echo off
echo _______________________________________
echo _______________________________________
echo Please Connect Your Phone,
echo Connect The USB Cable,
echo Power It Off,
echo Hold Windows Button And Power Button Till
echo You Get In The FastBoot Mode,
echo Flashing...
fastboot -c "" -b 0x11800000 flash:raw boot zImage initrd.gz
echo Flashing Complete
fastboot reboot
7.reboot
The Rom success coming into the system.
if i don't flash charan_05152011_cLK_ppp_cache.zip,the wifi works normally,but GPRS or 3g is not working.
thanks, i really appreciate the guide. Its a nice easy to flow for those would count figure it out before.
i prefer clk over magldr. But i still get very frequent data drop outs in areas with low service. magldr has zero issues reconnecting. Clk normally requires a airplane mode or a reset to get service back.
chshrm said:
actually I can make any MAGLDR rom boot by CLK including sense rom, but one problem I cannot solved. that is the wifi not working.
steps are as follows:
1.flash Task 29 with Radio 2.15.50.14
2.flash clk 1.4.0.1
3.flash cLK_Rcovery 3.2.0.0 (size depending on rom's requirement)
4.flash ROM（zip package）
5.flash charan_05152011_cLK_ppp_cache.zip
6.flash Kernel initrd.gz and zImage（take from Zip Rom）
@echo off
echo _______________________________________
echo _______________________________________
echo Please Connect Your Phone,
echo Connect The USB Cable,
echo Power It Off,
echo Hold Windows Button And Power Button Till
echo You Get In The FastBoot Mode,
echo Flashing...
fastboot -c "" -b 0x11800000 flash:raw boot zImage initrd.gz
echo Flashing Complete
fastboot reboot
7.reboot
The Rom success coming into the system.
Click to expand...
Click to collapse
Have you try to chmod 777 the file bcm4329.ko?
john_matrix said:
Have you try to chmod 777 the file bcm4329.ko?
Click to expand...
Click to collapse
i don't know the function of this file, and actually it is included in the patch package.
Situation is that:
if i don't flash charan_05152011_cLK_ppp_cache.zip,the wifi works normally,but GPRS or 3g is not working. if i use this patch, wifi not working, but GPRS or 3g become normal.
1) Backup your System first
(Needed)
2) Now download this file here -
Download (unupdate.zip) search at google.
3) Now copy Unupdate.zip file to the
SD Card. Do Not put it in any folder.
It ain't work.
4) Turn Off your Device and go to
Recovery Mode By Pressing and
Holding this Key Combination
Volume Up + Home Button +
Power Button.
5) Once you entered into the
Recovery Mode. You will see the Blue
Color User Interface where you
can't use Touchscreen. Instead use
" Volume Up and Volume Down to move
Up and Down". And "Home Button to
Select". And "Power Button used to
go Back"
7) After that select "Apply Update
from SDCard" option and choose
"Unupdate.zip".
8) Once Patching was successful. You
have to Reboot your Phone by select
" Reboot System Now".
Vola!!!! You're successfully UnRooted
your phone.
Hope it work
+---------------------------------------+
ADD My Facebook:
[email protected]
Sincerely,
Eirma SyaQieLa
(Malaysia User)
-Nice To Meet You
HTC DESIRE SV FORUM:
This forum has been created for HTC Desire SV mobile users
This will help you in rooting , unroooting , unlocking boot loader , installing stock,custom rom , swapping memory , etc with htc desire sv
Unlocking boot loader and Rooting:
Post #2
Custom Rom:
Post #3
Common Questions and their answers:
Post #4
Getting back to mobile purchased:
Installing stock rom
Re-Swapping memory
Delete Superuser app
Re-lock bootloader
Post #5
Updates:
Swapping Int and Ext_sd
Bootloader unlock tool
Super SU update and pro version
HTC desir svTweaks
Recovery.img files and google drive
Installing an app as system app
Post #6
Modifications and embellishments:
Post #7
PRECAUTION (must read):
Post #8
Best Of Best:
Aroma File Manager(To use in recovery menu)
Aroma Font Manager(To use in recovery menu)
Post #9
Themes:
Post #15
FULL WIPE:
[includes: wipe data / factory reset + wipe cache partition + format / data + format cache + format system + wipe dalvik-cache (+ wipe battery stats)]
Post #52
Unlocking bootloader and Rooting
Unlocking BOOTLOADER
Things to Remember
o This guide is only for the HTC DESIRE SV. Do not attempt the following steps on any other device.
o The warranty will be voided after the unlock.
o Make sure your battery is charged to at least 80%.
o If you are unsure about any step, ask us in the comment section before proceeding further.
Thing to be Done
o All the files will be wiped after the unlock so take backup of all your important data.
o Enable USB debugging from the Developer options.
o Download and install the HTC Sync Manager from this link.
o Download Fastboot zip file from this link and extract the contents into a folder namedFastboot.
o Disable antivirus software on your system to avoid unnecessary interference.
Step-by-step Guide to Unlock HTC DESIRE SV Bootloader
o Go to the website www.htcdev.com and register yourself. Make sure to verify the email to complete the registration process.
o Login to the htcdev website and then go to the Unlock Bootloader page.
o Click the drop down devices list Under supported devices and select the option ‘All Other Supported Models‘. (select htc desire because htc desire sv will be not in the list)
o Click on ‘Begin Unlock Bootloader’ and select Yes on the confirmation screen.
o Acknowledge messages on the Legal Terms and click on ‘Proceed to Unlock Instructions’.
o The next page with unlocking bootloader instructions will give you 4 steps to follow: Disconnect mobile from the PC if connected and then switch off the device. Then pressVolume Down button and Power button to start the device in Bootloader mode. Once it’s in Bootloader screen, highlight Fastboot option and press the Power button. Then connect your HTC DESIRE SV to PC via USB cable.
o Click on Proceed to step 5. But it’s not required to follow the steps mentioned in the second page of htcdev site. Instead you go to the Fastboot folder which we have extracted earlier and hold the Shift key and at the same time right click on the free space. Select the option ‘Open command window here’.
o Windows command window will appear like ‘..\Fastboot>’. Now you need to enter the following command in the command line fastboot devices (This command will tell you whether your device is detected by your computer or not. If your device shows you can go ahead with the next step. If the device is not detected the command screen will not show any information and in this case you have to re-install the HTC Sync Manager and reboot your PC. Then redo the tutorial from the beginning.
o Keep open the command window. Then go to the third page of instruction in htcdev by clicking on ‘Proceed to Step 8‘ button.
o Follow the steps mentioned in the third page of htcdev site (from step 8 to step 10). When all the steps are done, click on Submit button.
o If all the steps are done properly you will get a message ‘Token Submitted Successfully!’ and the Unlock Key information is emailed to you.
o Open the email from HTC and download the attached file named ‘Unlock_code.bin’.
o Once the download is done copy the ‘Unlock_code.bin’ file to Fastboot folder.
o Now go back to the command window and the following command: fasboot flash unlocktoken Unlock_code.bin
o Now the HTC DESIRE SV will get a message to Unlock bootloader. Press Volume up and select YES, then press Power button to confirm the action.
o Your HTC DESIRE SV will now restart and ask to complete the factory reset process. You can now disconnect your device from the PC.
That’s all! You have successfully Unlocked the Bootloader of your HTC DESIRE SV. Now you can root and install Custom ROMs on your device without any issues.
ROOTING HTC DESIRE SV:
1.)Dowload android.rar from link
2.)download superuser.zip from link
3.)Rooting:
[steps:]
*switch off your mobile
*click volume down and power button simultaneously to enter boot menu
*click fastboot
*connect your device to pc via usb
*it will be appearing fastboot usb in the mobile
*extract downloaded file to c:\
*copy super user.zip to your external sd card
*click winkey+r and type cmd to enter command prompt
*type cd\
*type cd android to enter into c:\android where the files are present
*type fastboot flash recovery recovery.img
*you will get success notification in command prompt
*type fastboot reboot-bootloader
*click recovery
*wait for few minutes it wil show entering recovery... and it wil enter black screen after 2 minutes it wil enter recovery
*click install zip via sd card
*select zip file from external sd
*click yes to install
*congratulation your HTC DESIRE SV mobile is rooted now
Custom rom(htc desire sv)
INSTALLING CUSTOM ROM:
1. Fill the firmware to the memory card. (No need to unpack)
2. Turn off the phone. We take out the battery and insert back. Turn it pinching button VolDown + Power.
3.Select Fastboot, select Recovery, get into the menu CWM Recovery.
4.Use volume keys to select backup and restore and select backup. Wait for 5-10 minutes. CWM Recovery creates a backup of your system in the card catalog type clockworkmod / backup / date backup. Rename this directory is not recommended! To organize the directory must to 1GB of free space. If necessary, it can be transferred to and stored on a computer folder with preservation of architecture. Then, when you install custom firmware failed or that fails, you will always be able to restore the original state of the system: backup and restore → restore → select → confirm by Power button.
5. After a successful backup system, go to the firmware kernel.
From the archive IMG Galickijj sews kernel (boot.img) is mandatory. (manual firmware kernel header)
After flashing the kernel go to Fastboot, select Recovery, get into the menu CWM Recovery.
proceed to the cleaning system (Wipe, Wipe), the cache from the old firmware.
choose in CWM Recovery point to:
- wipe Data / factory reset
Advanced / wipe dalvik cache
Go back to the main menu CWM Recovery.
6. Go directly to the installation of the firmware. To do this, select the menu item CWM Recovery
- install ZIP from sdcard → Choose ZIP from sdcard
- choose a file
- confirm by Power button
After installing CWM Recovery will show you the message
Install from sdcard complete.
Doing a reboot.
Be patient, the first load system is long, wait about 5-10 minutes until the system is booted.
custom rom list:
Mod Edit: Links removed for warez:
6. Do not post warez.
If a piece of software requires you to pay to use it, then pay for it. We do not accept warez nor do we permit any member to request, promote or describe ways in which Warez, cracks, serial codes or other means of avoiding payment, can be obtained. This is a site of developers, i.e. the sort of people who create such software. When you cheat a software developer, you cheat us as a community
Common Questions and their answers
Q1.
WiFi not working after installing custom Rom :
#switch off you mobile
#get into fastboot by pressing power and volume down button
#go to command prompt and navigate to c:\android where sdk files downloaded from post #1 is present
#copy boot.img from custom rom installed to c:\android
#in cmd type fastboot flash boot boot.img
#after getting success , reboot your phone
$##$ Your wifi will be working now
Q2.
How to s-off HTC Desire sv?
Many people were trying to find how to s-off and if you try by another other method it's may lead your device bricking.
Q3.
When I delete a file in system/app or some root files it deleted and after reboot it's there?
Well, then the only conclusion that a temporary root access still can live, but without S-off you cant make sense to remove the application so as to restore...
Q4.
Is Jellbean rom available for HTC desire sv or how to upgrade to jelly bean?
Jelly bean rom is currently un available and many forum developers were developing rom as rom porting fails with htc desire sv it will take some time .....
Q5.
In ClockworkMod recovery_menu my screen is slighly left when I press down and it comes back to normal when I press the down button again .... Is the problem on my mobile?
If you mean when you click on the menu items that shift...It is normal feature of the ClockworkMod recovery. No worries
Getting back to mobile purchsed
This will help you in getting back your mobile which you have purchased.
The steps involved here are:
Installing stock rom without root permissions
(or)
To delete SuperUser app and
To re-swap memory(If you haven't installed any custom rom)
(and)
Re-locking bootloader
Installing stock rom without root permissions:
If u have stock rom of your mobile backed up anyway it won't be useful because it's rooted.
So download stock rom from here:
LINK1
LINK2
Refer Post #48 for stock ROM (2 Versions)
Rom info:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
copy to your ext_sd card and flash it via recovery
Re-Locking bootloader:
put your phone in bootloader mode:
Switch OFF your phone.
Press and hold “Volume down + Power button” together until your phone boots into bootloader mode.
Select Fastboot using the Power button.
Use the Volume buttons to go up & down and Power button to select the highlighted option in the bootloader mode.
Connect your phone to the PC with a USB Cable.
Open the fastboot folder c:\android
Then open a Command prompt window inside the fastboot folder.
To do this → “Shift + Right Click” on any empty white space inside the folder and select the ‘Open command window here’.
Type the following in the command prompt window:
fastboot devices
This is to ensure that your device is detected, if nothing appears on screen with this command, then it means you don’t have the proper drivers installed on your PC. And if that’s the case you should download and install/re-install the HTC Sync software given in Step 1.1
Now type the following command to re-lock your HTC One X bootloader
fastboot oem lock
That’s all. Your phone’s bootloader is now re-locked and it’ll reboot automatically
To confirm, boot into bootloader mode and you’ll see “RELOCKED” written with a pink highlight at the top of the screen
To re-swap memory(int_sd and ext_sd)
download this file: Link
copy to ext_sd card
Flash via recovery
To delete SuperUser app(system):
Downlaod this file: Link
copy to ext_sd card
Flash via recovery
Updates
Swapping Internal_SD and Ext_sd in HTC DESIRE SV
Download this file and place it on your external card(keep a back up of your sd and ext_sd as the contents wil be deleted fully):
Link
Steps:
1.)go into recovery mode
2.)click select zip from sd card and browse the file
3.)click yes to install
4.)It will take few seconds
5.)go back and click reboot now.
6.)install all apps that you have backed up
7.)now you have successfully swapped ext_sd and int_sd
Note:
Don't rename the file you have downloaded or don't edit the contents..
HTC Boot loader unlock tool:
Link to download
follow onscreen instructions to unlock boot loader
Super Su Update Pro:
Link :
6. Do not post warez.
If a piece of software requires you to pay to use it, then pay for it. We do not accept warez nor do we permit any member to request, promote or describe ways in which Warez, cracks, serial codes or other means of avoiding payment, can be obtained. This is a site of developers, i.e. the sort of people who create such software. When you cheat a software developer, you cheat us as a community
HTC DESIRE SV google drive(my files):
Link
Recovery.img files:
Here comes recovery.img files working on HTC desire sv.The stock version is named as stock_recovery and other two clockword mod recvoery versions working on desire sv are 6.0.2.8(touch version and keys version) and 6.0.3.2(touch version)
Links for downloading:
download.........
HTC Desire sv tweaks:
This helps in improving our performance, hardware acceleration, the search interval Wi-Fi networks, saving battery power, a smoother interface, improved the quality of photo, audio and video recording camera, etc.
"VSV_Tweaks" tweaks build.prop (Tweaking )
Installation :Before installing make backup! 1. copy the file to memory card 2. reboot into Recovery 3. In the Recovery menu, select the item advanced -> wipe dalvik cache 4. Select an option in Recovery - install zip from sd card 5. Specify the path to the file VSV_Tweaks 6. Reboot your phone, when installation is complete.
Who does not like to install the patch build.prop (stock) or restore the backup.
Links:
VSV_tweaks.zip
build.prop.zip
Installing an app as system app:
1. Download the archive.
2. Open it (I used winrar.)
3. Add the desired installation file (*. Apk) in the folder system / app in the archive and save it.
4. * do not touch anything..
5. Copy the zip to our microSD card .
5. Run the phone to recovery
6. Select install zip from sdcard, then choose zip from sdcard, choose zip and clock yes to install.
7. select go back(after successful installation)
8. select Reboot System now to reboot your phone
Modifications and embellishments for HTC Desire SV T326e
This post contains:
Wallpapers
Icons
Themes
Fashion dialer
Fashion keyboard
Wallpapers:
Sense 5 wall papers
Themes:
Classic theme:
Link
Sense 5 Theme
Link
Themes continued in Post #15
will be updated soon
Precaution
PRECAUTION for Brick(HTC DESIRE SV)
This is really a necessary post which will help you how to prevent yourself from your mobile getting bricked
Mostly many people have told that volume down and power button pressing to enter recovery made my mobile brick and this is a main cause for getting bricked, because many people will press volume up/down and power sometimes it may make your hardware fail.
so to prevent this we have used techniques to get your mobile to fastboot without using buttons,just connect mobile via PC via USB on any mode(charge only,media storage)
Download this file
Link to download
and
Run fastboot.bat to enter fastboot
Run stock_recovery.bat to install stock recovery.img
Run cwm_recovery.bat to install cwm_recovery.img ( U can also replace cwm_recovery.img by any version supported for the device)
These files should be usually placed in c:\android as all the procedures are following steps with that.
BACK UP ROM:
Even backing up rom is necessary thing. a copy of backed_up rom should be in PC
If something went bad with installing custom rom , you can easily roll back to previous rom which you have backed up
Best of Best
Now this Post if for Aroma File manager and Aroma Font manager:
What is Aroma file manager:
Android Recovery was powerful system. But it was pain when it come to managing your file system
But now AROMA File manager is available for everyone to do this common tasks.
So you can access files through a file manager in recovery menu called Aroma File manager
What is Aroma Font manager:
It's hard to Change fonts on a S-ON device as the files replaces in system will not be permanent.
This made easier by Aroma Font Installer
Fonts Available:
- Android Logo
- Gingerbread Stock
- MeeGo
- Nokia Pure View Font
- Roboto(Stock)
- Ubuntu
- Windows Phone 7
- Sony Xperia S
How to Use:
1. Download and copy the file in your SDcard.
2. Boot on Recovery.
2. Choose install zip from SDCARD.
Download:
Aroma_Font_Manager
Aroma_File_Manager
:good::good::good::good::good:
last post reserving so
Download Speed
prasath kp said:
INSTALLING CUSTOM ROM:
1. Fill the firmware to the memory card. (No need to unpack)
2. Turn off the phone. We take out the battery and insert back. Turn it pinching button VolDown + Power.
3.Select Fastboot, select Recovery, get into the menu CWM Recovery.
4.Use volume keys to select backup and restore and select backup. Wait for 5-10 minutes. CWM Recovery creates a backup of your system in the card catalog type clockworkmod / backup / date backup. Rename this directory is not recommended! To organize the directory must to 1GB of free space. If necessary, it can be transferred to and stored on a computer folder with preservation of architecture. Then, when you install custom firmware failed or that fails, you will always be able to restore the original state of the system: backup and restore → restore → select → confirm by Power button.
5. After a successful backup system, go to the firmware kernel.
From the archive IMG Galickijj sews kernel (boot.img) is mandatory. (manual firmware kernel header)
After flashing the kernel go to Fastboot, select Recovery, get into the menu CWM Recovery.
proceed to the cleaning system (Wipe, Wipe), the cache from the old firmware.
choose in CWM Recovery point to:
- wipe Data / factory reset
Advanced / wipe dalvik cache
Go back to the main menu CWM Recovery.
6. Go directly to the installation of the firmware. To do this, select the menu item CWM Recovery
- install ZIP from sdcard → Choose ZIP from sdcard
- choose a file
- confirm by Power button
After installing CWM Recovery will show you the message
Install from sdcard complete.
Doing a reboot.
Be patient, the first load system is long, wait about 5-10 minutes until the system is booted.
custom rom list:
1.) custom firmware IMG Galickijj for HTC Desire SV based on 1.07.401.6 ICS 4.0.4 :
Link to download:
custom firmware IMG Galickijj for HTC Desire SV based on 1.07.401.6 ICS 4.0.4 HTC Sense 4.1
Features:
Root core
applications Root
Deodexed & Zipaligned
Memory optimization it right now
(with the ability to move applications to the SD
when connected to a PC otkryvaetsya only SD)
Support Init.d scripts
Ramdisk
EXT4
Zipalign mount system partitions
improved picture quality and 100%
GPU accelerated
reduction "lags" when dialing to improve responsiveness of the screen
improved battery saving
Android debugging icon is removed to improve the video quality of some errors in applications
improve the speed of the Internet
to improve reading speed SD
GPS is optimized
SystemUI Mod
Sound lock / unlock
Advanced Topics
Fixed calculator
changed Boot animation
You can put embellishment
Ad Blocking applications
, etc.
Applications(extra):
QuickPanel
Quick Settings Panel
EsFileExplorer
EsTaskManager
SuperSU
Adobe Flash Player
BusyBox Pro
2.)Firmware FULL DEODEX for HTC Desire SV cid HTC_A48
Link To download:
Firmware FULL DEODEX for HTC Desire SV cid HTC_A48
Features:
* brushed rom
* full deodex
* installed necessary tools
* root - system patch
* LiDRoiD Quick Access Toolbar - system patch
* battery in 1% increments - system patch
* pre installed stock + new themes
* memory are reversed, and the built-in SD - System Patch
* patch calculator
Applications(extra):
SuperUser
TotalCommander
TimeSyncPro
RootExplorer
Calculator - (human)
SambaFilesharing
QuickSetting panel LiDRoiD
***** patch system means that it in no way can affect your resources, i.e guzzle battery, etc. etc.
Click to expand...
Click to collapse
The download speed is limited on that site. Please upload it to google drive or yandex disk.
karaman_deniz said:
The download speed is limited on that site. Please upload it to google drive or yandex disk.
Click to expand...
Click to collapse
google drive link updated for 2nd rom but for 1st rom it's uploded by another persona nd i don't have google drive link. i'm sorry
can the themes b installed on any htc non rooted phone?
---------- Post added at 09:32 AM ---------- Previous post was at 09:23 AM ----------
can you upload more themes ..i am looking for these themes forever!! Thank you so very much
getting back to mobile purchased
can u pls tell me the procedure for restoring...I extracted the stock rom into external sd..after that in recovery mode I choose restore and install...but it is nt working..pls help...
Here are some themes for sense 4.1(no root needed)
Yellow theme:
Link to download...
Matte theme:
Link to download...
Retro theme
Link to download
Tron theme
Link to download
Beats by dre theme
Link to download
Holiday theme
Link to download
All credits go to the developer of the themes..I am just posting theme..
kulveer007 said:
can u pls tell me the procedure for restoring...I extracted the stock rom into external sd..after that in recovery mode I choose restore and install...but it is nt working..pls help...
Click to expand...
Click to collapse
step1:
Download and Copy the file to external sd card...
step2:
There are two types of files available
if the file is .zip select install zip from sd vard and browse the .zip file and click yes to install
if the file is in folder (system. tar,boot.img,data.tar,etc...) you have to copy the folder(name wil be date and time) to clockworkmod\backup\ and go to recovery and choose restore/back up and click restore and choose the folder
Hit thanks if i helped you
zerohunk said:
can the themes b installed on any htc non rooted phone?
---------- Post added at 09:32 AM ---------- Previous post was at 09:23 AM ----------
can you upload more themes ..i am looking for these themes forever!! Thank you so very much
Click to expand...
Click to collapse
yeah uploaded more and even more themes will be uploaded soon
Cant restore
bro i download CWM Recovery_Stock(root)_HTC_Desire_SV.rar...and copy folder (with date and time) in cloakwrk/backup...in recovery i choose backup and restore then restore...then i selected the folder...after a minute it is showin cant open /cache/recovery/last_log...
thank you very much for all your documents which is translated from russian forum and your devolopment. you are the only one devoloper who works on desire sv. this thread is awesome for users. i tried your way to root my device and i succeed, thank you again. i will customize my device with your tweaks,custom roms exc.
edit: so which is your recommended rom ? deodex or the other?
edit2: sorry for my bad english
help
kulveer007 said:
bro i download CWM Recovery_Stock(root)_HTC_Desire_SV.rar...and copy folder (with date and time) in cloakwrk/backup...in recovery i choose backup and restore then restore...then i selected the folder...after a minute it is showin cant open /cache/recovery/last_log...
Click to expand...
Click to collapse
Dude you have to extract that file to clockworkmod/backup\folder(where the folder name will be date and time of back up)
then in recovery menu select backup and restore--->restore-->select the folder-->click yes to install
happy day
Hi guy!!
First I'm sorry for my english
I have Samsung note sgh-i717r(rogers canada), now I live in italy, I try to unlock, but nothing.
So the phone see the sim(contact and service in the sim) but not see the network(wind italy).
android version 4.1.2
1) Download Odin, CWM tar, and superuser zip (http://forum.xda-developers.com/show....php?t=1763896 Post # 3)
2) Install Odin
3) Copy superuser zip file to Phone
4) Start Odin and browse for the CWM tar file in the PDA section
5) Put the phone into download mode (VOLUME DOWN + POWER, then VOLUME UP)
6) Connect Phone to PC
7) Flash CWM with Odin
8) As the phone is rebooting, take out the battery. This is done to avoid the script install-recovery.sh from reinstalling stock recovery
9) Put battery back and boot into recovery (VOLUME UP + VOLUME DOWN + POWER, Release POWER after first vibration)
10) Install superuser ZIP from CWM, you are now rooted
11) Reboot phone
12) Install root explorer or ES File explorer and enable root operations and /system mount on them.
13) Find /etc/install-recovery.sh and rename it to install-recovery.sh.bkp
14) Repeat steps 4 to 7
15) Reboot. You should now have CWM and Root.
then
Go to dailer screen. press *#197328640#
The screen will change to the hidden menu as soon as you hit the last # key in the dailer
press [1]DEBUG SCREEN
Press [8]PHONE CONTROL
Press [5] SIMULATION
Press [6] NETWORK LOCK
Press [3] PERSO SHA256 OFF
Wait exactly 30 seconds
press the menu key on the phone and select back option. This will take you back to
NETWORK LOCK screen.
but this [4] NW LOCK NV DATA INITIALLIZ not appears
And if I install SGH-T989_UVLE1_radio.zip the menu don't work(I can see main menu but can't navigate)
Do you have some solutions?
Thank you!!