Related
For those of you who keep getting stuck on the splash screen after trying to restart your phone after installing a 4.3 ROM.
My steps were (and I take no credit for this, I can't remember who had said to do this and I wasn't logged in so I couldn't click the thank you button):
*Note* If you were already on the Stock 4.3 ROM you do not want to flash the 4.0.4, 4.1.1 or 4.1.2 Stock ROM since you will brick your phone. The Stock ROM contains the Bootloader which should never be downgraded. Fyi: the Bootloader is not the Baseband, the Baseband is just what Modem you're using.
1. Use Odin to flash the latest stock ROM
2. Enter the stock recovery and do a factory reset and clear the cache (I did both twice just to make sure)
3. Use Odin to flash the stock rooted ROM.
4. Enter the stock recovery and do a factory reset and clear the cache. (This might not be necessary but I did anyways just to make sure)
5. Use Odin to flash a custom recovery (TWRP 2.6.0.0 was the newest recovery when I did this last week)
6. Enter the custom recovery and wipe everything, then flash whatever 4.3 based ROM and then flash GApps if you want.
*Note* It seemed like the phone was hanging on the splash screen after either the initial boot or the first restart (I can't remember which, it's been a week) but it did boot and reboot fine.
I hope this helps out some people since I found it to be quite irritating that I could install a 4.3 ROM and set everything up but when I went to restart it would hang at the splash screen (going into the recovery and clearing the cache/dalvik cache wasn't helping).
Are you basically saying to revert back to stock settings and redo the entire root process again?
Sent from my SGH-I747 using xda app-developers app
bullet2binary said:
Are you basically saying to revert back to stock settings and redo the entire root process again?
Sent from my SGH-I747 using xda app-developers app
Click to expand...
Click to collapse
Yeah, from what I had read that seemed to be necessary since I had used Odin to update the bootloader (MF1 since my phone is the M variant) by itself when the newest Stock ROM had come out a while ago. I still flashed the newest Stock ROM (same MF1 bootloader for the M variant) but the first time I did it I forgot to enter the Stock Recovery to do a Factory Reset and Clear the Cache and ended up stuck on the splash screen of a 4.3 ROM after flashing a custom recovery. So I needed to reflash back to stock and start over.
Going into the Stock Recovery and doing a Factory Reset and Clearing Cache is necessary and doesn't take much time at all so you may as well do it just to be sure. I also recommend backing up your IMEI if you haven't done it yet.
spongdangly said:
Yeah, from what I had read that seemed to be necessary since I had used Odin to update the bootloader (MF1 since my phone is the M variant) by itself when the newest Stock ROM had come out a while ago. I still flashed the newest Stock ROM (same MF1 bootloader for the M variant) but the first time I did it I forgot to enter the Stock Recovery to do a Factory Reset and Clear the Cache and ended up stuck on the splash screen of a 4.3 ROM after flashing a custom recovery. So I needed to reflash back to stock and start over.
Going into the Stock Recovery and doing a Factory Reset and Clearing Cache is necessary and doesn't take much time at all so you may as well do it just to be sure. I also recommend backing up your IMEI if you haven't done it yet.
Click to expand...
Click to collapse
This seems to have done the job. Running PAC 4.3 right now. I've rebooted successfully once so far.
Sent from my SAMSUNG-SGH-I747 using xda app-developers app
Exactly what I ended up doing after nothing else was working. After getting it hanging the first time, even flashing 4.2 roms was giving me boot issues. After reverting back to stock and reflashing I'm now running the 9/1 Pac nightly and the 8/31 kt747 kernel.
I'm probably 10+ reboots in without issue and I flashed the kernel separately!
bullet2binary said:
This seems to have done the job. Running PAC 4.3 right now. I've rebooted successfully once so far.
Sent from my SAMSUNG-SGH-I747 using xda app-developers app
Click to expand...
Click to collapse
exodus454 said:
Exactly what I ended up doing after nothing else was working. After getting it hanging the first time, even flashing 4.2 roms was giving me boot issues. After reverting back to stock and reflashing I'm now running the 9/1 Pac nightly and the 8/31 kt747 kernel.
I'm probably 10+ reboots in without issue and I flashed the kernel separately!
Click to expand...
Click to collapse
I'm glad to hear that this seems to be the proper fix. That's odd that you were having trouble with 4.2 ROMs, but then again I'd been running 4.2 ROMs on my phone since they first started rolling out. It's kind of annoying that everyone's S3 seems to be slightly different then the next.
Yeah this was a weird one all right. Just glad this post had a solution
Sent from my SAMSUNG-SGH-I747 using xda app-developers app
glad i found this otherwise my first noob post would have truly been a noob move. Thanks wouldn't have guessed that fix for a few days at least.
verified it works. but it did require some weird time dealing with a bootloop issue on stock recoveries. had to find a .tar version of CWM to flash via odin for the final result.
Still Stuck at Splash Screen after trying to upgrade to 4.3
Background:
I had been running task's rom since 4.1.x. Upgraded to 4.2 with not problems and I kept the rom current. Tried to upgrade to 4.3 and that is where the problems started. It appeared to work, saw that Google was updating a number of apps but then then I kept getting error messages regarding various about various processes stopping unexpectedly. Rebooted the phone and it came up with Task's kernel splash screen where it remains frozen.
I can get into TWRP (v2.3.3.1) recovery and into Download mode.
I have tried wiping Cache and Dalvik Cache
I have wiped System
I have done a Factory Reset
I have Formatted Data
I have used Odin twice to get back to stock (I747UCDLK3) and both times it says "passed."
When I try to reboot it, however, it comes back to Task's Kernel splash screen (I do not see the Samsung screen)
Any help or suggestions would be great.
UPDATED: Found an older update from April and was able to restore it. Still wondering why 4.3 wouldn't take.
This Works
I was skeptical, but this actually works! Now running Task's 4.3 on my bell i747m without any problems!
Thanks for the tip OP :good:
spongdangly said:
For those of you who keep getting stuck on the splash screen after trying to restart your phone after installing a 4.3 ROM.
My steps were (and I take no credit for this, I can't remember who had said to do this and I wasn't logged in so I couldn't click the thank you button):
1. Use Odin to flash the latest stock ROM
2. Enter the stock recovery and do a factory reset and clear the cache (I did both twice just to make sure)
3. Use Odin to flash the stock rooted ROM.
4. Enter the stock recovery and do a factory reset and clear the cache. (This might not be necessary but I did anyways just to make sure)
5. Use Odin to flash a custom recovery (TWRP 2.6.0.0 was the newest recovery when I did this last week)
6. Enter the custom recovery and wipe everything, then flash whatever 4.3 based ROM and then flash GApps if you want.
*Note* It seemed like the phone was hanging on the splash screen after either the initial boot or the first restart (I can't remember which, it's been a week) but it did boot and reboot fine.
I hope this helps out some people since I found it to be quite irritating that I could install a 4.3 ROM and set everything up but when I went to restart it would hang at the splash screen (going into the recovery and clearing the cache/dalvik cache wasn't helping).
I hope I posted this in the right section but apologies if it's not.
Click to expand...
Click to collapse
If this works you're a life saver! I've been posting around 4.3 threads about this for weeks and no one came up with a decent answer....
Tried reflashing stock with root but didn't work... i'll try your way, see if that works
Gonna try this tonight!!!
Thanks!
I posted in the CM thread about this, but thought I would pass it along.. I didn't have to go back to stock non-rooted. What I did:
I odin'd Mr. Robinson's LK3 rooted
Factory reset from the 3e recovery
Rebooted
Odin'd twrp
Restored nandroid of CM
Good to go.
Solved
Thanks, also works for i727 skyrocket
wont this brick people phones flashing back 4.1.1 stock ? im on stock 4.3 stuck on samsung galaxy s3 logo meaning flashing back to latest stock rom using odin 4.1.2? 4.3 stock rom or 4.3 custom roms?
Kastro1784 said:
wont this brick people phones flashing back 4.1.1 stock ? im on stock 4.3 stuck on samsung galaxy s3 logo meaning flashing back to latest stock rom using odin 4.1.2? 4.3 stock rom or 4.3 custom roms?
Click to expand...
Click to collapse
spongdangly said:
1. Use Odin to flash the latest stock ROM
Click to expand...
Click to collapse
If you were already on the Stock 4.3 ROM you do not want to flash the 4.0.4, 4.1.1 or 4.1.2 Stock ROM since you will brick your phone.
I'll add a note to the OP about not attempting to downgrade to an older Stock ROM though.
spongdangly said:
If you were already on the Stock 4.3 ROM you do not want to flash the 4.0.4, 4.1.1 or 4.1.2 Stock ROM since you will brick your phone.
I'll add a note to the OP about not attempting to downgrade to an older Stock ROM though.
Click to expand...
Click to collapse
what framware did you flash to get 4.3 back working ? a leaked 4.3 Rom with no root ? thien reflash the stock 4.3 ?
Kastro1784 said:
what framware did you flash to get 4.3 back working ? a leaked 4.3 Rom with no root ? thien reflash the stock 4.3 ?
Click to expand...
Click to collapse
When I had done this back in August, I flashed the Rogers 4.1.2 Stock ROM since that was the latest stock firmware at the time and I have a Canadian S3.
If you had already flashed or been on the Stock AT&T 4.3 ROM, I'd recommend reflashing the latest Stock AT&T 4.3 ROM and following the instructions in the OP. Just make sure that you don't attempt to flash an older version of the Stock ROM that you were already on since you will brick your phone. The Stock ROM contains the bootloader and that cannot be downgraded. I don't have an American S3 since I'm Canadian so I don't know which 4.3 bootloader is the newest although I'm sure a quick search would answer that for you.
spongdangly said:
When I had done this back in August, I flashed the Rogers 4.1.2 Stock ROM since that was the latest stock firmware at the time and I have a Canadian S3.
If you had already flashed or been on the Stock AT&T 4.3 ROM, I'd recommend reflashing the latest Stock AT&T 4.3 ROM and following the instructions in the OP. Just make sure that you don't attempt to flash an older version of the Stock ROM that you were already on since you will brick your phone. The Stock ROM contains the bootloader and that cannot be downgraded. I don't have an American S3 since I'm Canadian so I don't know which 4.3 bootloader is the newest although I'm sure a quick search would answer that for you.
Click to expand...
Click to collapse
There is no latest Stock AT&T 4.3 ROM right now to reflash if you're already on the Stock AT&T 4.3 ROM. We cannot keep telling people this. If so, tell us how, because no one has, as of yet.
I've seen entirely too many posts telling people who are having trouble or phone is soft bricked on the Stock AT&T 4.3 ROM to flash or Odin back to stock. Then when asked how, the discussion ends.
That's also one of the reasons why I refuse to upgrade to 4.3 right now. At least I can still Odin back to stock as an option if something does goes wrong, but who am I to tell anyone to stay away from the latest toy, I mean update?
shortydoggg said:
There is no latest Stock AT&T 4.3 ROM right now to reflash if you're already on the Stock AT&T 4.3 ROM. We cannot keep telling people this. If so, tell us how, because no one has, as of yet.
I've seen entirely too many posts telling people who are having trouble or phone is soft bricked on the Stock AT&T 4.3 ROM to flash or Odin back to stock. Then when asked how, the discussion ends.
That's also one of the reasons why I refuse to upgrade to 4.3 right now. At least I can still Odin back to stock as an option if something does goes wrong, but who am I to tell anyone to stay away from the latest toy, I mean update?
Click to expand...
Click to collapse
I'm sorry that I'm unable to help. As I had mentioned I have a Canadian Rogers phone (since I'm in Canada) so I don't know what's going on with the AT&T Stock 4.3 ROMs other then the fact that lots of people are having problems.
If you never flashed or did an OTA update to 4.3 then I'd suggest flashing the Stock 4.1.2 ROM. That or try what Ozark_8125 did since it saves you a couple steps (just make sure that LK3 isn't an older ROM than the one you were on).
If you're unsure what bootloader is currently on your phone and your phone is rooted I'd highly recommend downloading one of the many Root Check apps from the Play Store to verify which bootloader you're currently on.
*Note* I don't know which bootloader is for the 4.1.2 AT&T ROM nor do I know which bootloader came with the 4.3 ROMs. I'm sure a simple search would answer that for you.
Ozark_8125 said:
I posted in the CM thread about this, but thought I would pass it along.. I didn't have to go back to stock non-rooted. What I did:
I odin'd Mr. Robinson's LK3 rooted
Factory reset from the 3e recovery
Rebooted
Odin'd twrp
Restored nandroid of CM
Good to go.
Click to expand...
Click to collapse
Samsung fixed my phone free thanks for the help
Sent from my SAMSUNG-SGH-I747 using Tapatalk
I tired to root my galaxy s3 but ended up bricking it for a while and all i got was the Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again. After trying odin so many time i finally got it to work but now i have another issue...i put verizon 4.1 on my phone using odin instead of att. my att sim wont work and i dont know how i am going to get it back to att stock rom so i can use my phone again!!! if anyone know how to reset this please help i just got the phone and now i cant use it because it has Verizon instead of att galaxy s3 stock rom on it.:crying:
pimpjayjay said:
I tired to root my galaxy s3 but ended up bricking it for a while and all i got was the Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again. After trying odin so many time i finally got it to work but now i have another issue...i put verizon 4.1 on my phone using odin instead of att. my att sim wont work and i dont know how i am going to get it back to att stock rom so i can use my phone again!!! if anyone know how to reset this please help i just got the phone and now i cant use it because it has Verizon instead of att galaxy s3 stock rom on it.:crying:
Click to expand...
Click to collapse
Did you ever flash android 4.3 on you're phone? (This is important)
Ali7000 said:
Did you ever flash android 4.3 on you're phone? (This is important)
Click to expand...
Click to collapse
it already had 4.3 i was trying to root it but the process faild and all i get is the error Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again
pimpjayjay said:
it already had 4.3 i was trying to root it but the process faild and all i get is the error Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again
Click to expand...
Click to collapse
Try these http://forum.xda-developers.com/showthread.php?t=2498233, stock at&t rooted without Knox (Believe me man, better without knox). But they are only leaks of the official firmware. I am not a professional developer so you might wanna create a new thread and ask if it's possible in you're situation.
Ali7000 said:
Try these http://forum.xda-developers.com/showthread.php?t=2498233, stock at&t rooted without Knox (Believe me man, better without knox). But they are only leaks of the official firmware. I am not a professional developer so you might wanna create a new thread and ask if it's possible in you're situation.
Click to expand...
Click to collapse
okay i will look it up and see if it works , thanks.
The Canadian and US phones are pretty similar. Maybe a Canadian rom will work?
You can find official firmware here: http://www.sammobile.com/firmwares/1/?model=SGH-I747&pcode=ATT#firmware
audit13 said:
The Canadian and US phones are pretty similar. Maybe a Canadian rom will work?
You can find official firmware here: http://www.sammobile.com/firmwares/1/?model=SGH-I747&pcode=ATT#firmware
Click to expand...
Click to collapse
No it won't work. Since it is a stock rom it most likely will not work, he won't be able to call, text, or use data.
Ali7000 said:
No it won't work. Since it is a stock rom it most likely will not work, he won't be able to call, text, or use data.
Click to expand...
Click to collapse
I wasn't sure if the OP could install some sort of stock firmware to get his phone going and then install the necessary radio.
audit13 said:
I wasn't sure if the OP could install some sort of stock firmware to get his phone going and then install the necessary radio.
Click to expand...
Click to collapse
The best choice for him is to stick to a custom rom until the AT&T 4.3 update releases.
Ali7000 said:
The best choice for him is to stick to a custom rom until the AT&T 4.3 update releases.
Click to expand...
Click to collapse
Wow. it seems as if you got people in here just giving you ODIN TARS to flash. i wouldnt listen/ flash anything than the leaked 4.3 update for att because MOST odin files have bootloader upgrades in them and if you are on 4.3 you will brick trying to restore stock
Andy_nu said:
Wow. it seems as if you got people in here just giving you ODIN TARS to flash. i wouldnt listen/ flash anything than the leaked 4.3 update for att because MOST odin files have bootloader upgrades in them and if you are on 4.3 you will brick trying to restore stock
Click to expand...
Click to collapse
Hah Yah man I've been through a lot sh**.
Sent from my SGH-I747M using XDA Premium 4 mobile app
At&t Tar files
what should i do, the tar file for Verizon still fails but it will go as far as to let my device boot but so i can at least get to recovery mode and then i can reboot it and clear system data but of courses that not what i want because it running Verizon.I is there a way to find the tar file that has at&t on it so i can try to make it work?
Ali7000 said:
Hah Yah man I've been through a lot sh**.
Sent from my SGH-I747M using XDA Premium 4 mobile app
Click to expand...
Click to collapse
what should i do, the tar file for Verizon still fails but it will go as far as to let my device boot but so i can at least get to recovery mode and then i can reboot it and clear system data but of courses that not what i want because it running Verizon.I is there a way to find the tar file that has at&t on it so i can try to make it work?
Based on the OP, the phone is currently running Verizon's 4.1 which leads me to believe the bootloader has not been updated beyond 4.1.2 since recovery mode is accessible; therefore, I think flashing 4.11 or 4.1.2 stock roms would be fine.
As always, it's best to check the installed bootloader before proceeding with any more flashes.
I used the stock firmware from here to downgrade my Bell s3 from stock 4.1.2 to stock 4.1.1.
Stock firmware: http://www.sammobile.com/firmwares/1/?model=SGH-I747&pcode=ATT#firmware
pimpjayjay said:
what should i do, the tar file for Verizon still fails but it will go as far as to let my device boot but so i can at least get to recovery mode and then i can reboot it and clear system data but of courses that not what i want because it running Verizon.I is there a way to find the tar file that has at&t on it so i can try to make it work?
Click to expand...
Click to collapse
Download the ATT Image
Current I747UCDLK3 (JB 4.1.1)
http://forum.xda-developers.com/showthread.php?t=1739426
audit13 said:
Based on the OP, the phone is currently running Verizon's 4.1 which leads me to believe the bootloader has not been updated beyond 4.1.2 since recovery mode is accessible; therefore, I think flashing 4.11 or 4.1.2 stock roms would be fine.
As always, it's best to check the installed bootloader before proceeding with any more flashes.
I used the stock firmware from here to downgrade my Bell s3 from stock 4.1.2 to stock 4.1.1.
Stock firmware: http://www.sammobile.com/firmwares/1/?model=SGH-I747&pcode=ATT#firmware
Click to expand...
Click to collapse
i wouldnt flash the bootloader just to to be safe though. id flash the recovery from the root forum and then install a cm or aosp ROM.
or open the tar and make sure there are not bootloader related files i forgot all of them but one is mbl. something and 1,2,3 theres a post on here how to check i just dont know where
As you'll soon discover, I'm a noob. I stupidly took the OTA update on my Samsung Galaxy S3 T-Mobile T999 from 4.1.2 to 4.3. Since doing so mine and my wife's phone (did the same thing to her also) gets in a mess after being connected to the car stereo bluetooth and prevents outgoing calls unless the phone is rebooted.
So to try to solve this, I rooted the phone and installed CM 11, so now I'm on 4.4.2. This didn't help the issue either and instead is worse at connecting to the bluetooth.
I want to get my phone back to the stock 4.1.2 rom, which I got from sammobile (PDA T999UVDMD5) or at worst back to the 4.3 stock rom (PDA T999UVUEMJC).
This morning I tried to flash T999UVDMD5_T999TMBDMD5_T999UVDMD5_HOME.tar using ODIN 307 but it failed almost instantly with an Fail! Auth message.
I also tried to flash CM 10.1 zip on my SD card using ClockworkMod Recovery v 6.0.4.5 but again it failed almost instantly (sorry I didn't take note of the error).
So now I'm back to CM 11. So any suggestions for how to get back to either of the stock roms?
huz666 said:
As you'll soon discover, I'm a noob. I stupidly took the OTA update on my Samsung Galaxy S3 T-Mobile T999 from 4.1.2 to 4.3. Since doing so mine and my wife's phone (did the same thing to her also) gets in a mess after being connected to the car stereo bluetooth and prevents outgoing calls unless the phone is rebooted.
So to try to solve this, I rooted the phone and installed CM 11, so now I'm on 4.4.2. This didn't help the issue either and instead is worse at connecting to the bluetooth.
I want to get my phone back to the stock 4.1.2 rom, which I got from sammobile (PDA T999UVDMD5) or at worst back to the 4.3 stock rom (PDA T999UVUEMJC).
This morning I tried to flash T999UVDMD5_T999TMBDMD5_T999UVDMD5_HOME.tar using ODIN 307 but it failed almost instantly with an Fail! Auth message.
I also tried to flash CM 10.1 zip on my SD card using ClockworkMod Recovery v 6.0.4.5 but again it failed almost instantly (sorry I didn't take note of the error).
So now I'm back to CM 11. So any suggestions for how to get back to either of the stock roms?
Click to expand...
Click to collapse
If you are getting errors in both odin and cwm, it sounds like it is a root issue. In other words, it sounds like the apps are being denied access to root and therefor cannot flash. Both odin and cwm are able to generate logs so you can tell the reason for the fail. Personally, I would recommend flasing twrp recovery instead of cwm since it seems to simplify alot and is a little better for our device. Without knowing exactly why the flash is failing, i would just recommend to try and re-root the phone again.
Did you put the phone in Downloading mode before connecting to the Odin ?
Do not try to flash 4.1.2 ever. It will brick your phone.
Perseus71 said:
Did you put the phone in Downloading mode before connecting to the Odin ?
Do not try to flash 4.1.2 ever. It will brick your phone.
Click to expand...
Click to collapse
Yes the phone was in downloading mode. I couldn't find any posts that thought that I would brick my phone for sure by downgrading so I thought I would try. Could I go back to the 4.3 Stock ROM with some degree of confidence?
Yes you can go back to 4.3 Stock.
Perseus71 said:
Yes you can go back to 4.3 Stock.
Click to expand...
Click to collapse
So I'm now back to Stock 4.3 by doing a flash via Odin. I did (stupidly) try to then go back to 4.1.2 again using Odin having put the phone in USB debugging mode first but I still got the same Auth Fail error.
Thanks for all the help.
huz666 said:
So I'm now back to Stock 4.3 by doing a flash via Odin. I did (stupidly) try to then go back to 4.1.2 again using Odin having put the phone in USB debugging mode first but I still got the same Auth Fail error.
Thanks for all the help.
Click to expand...
Click to collapse
You cannot downgrade like that once you have updated to official 4.3 firmware, no offence but why would you try it even after Perseus said not to? Anyway if you want to go back to 4.1.2 so badly just download a 4.1.2 ROM and flash it in recovery
Sent from my SGH-M919 using Tapatalk
serio22 said:
You cannot downgrade like that once you have updated to official 4.3 firmware, no offence but why would you try it even after Perseus said not to? Anyway if you want to go back to 4.1.2 so badly just download a 4.1.2 ROM and flash it in recovery
Sent from my SGH-M919 using Tapatalk
Click to expand...
Click to collapse
.
Thanks for the advice. I think I'll just quit while I'm only slightly behind now and remain on 4.3 Stock. I appreciate everyone's help and suggestions.
Downgrade from CM11 4.4.2 to 4.3 on I747
I went from 4.3 stock to CM11 on my i747 but i didnt like the update. So i am trying to go back to 4.3 however whenever i try to install the 4.3 zip file thru twrp or CWM, it fails. As far as i know there is no odin file for going back. I tried to flash rogers 4.3 file through odin (thinking i would flash at&t modem later) but that also failed.
I would appreciate any help on how to install 4.3 once 4.4.2 has been installed on an i747
You seriously need to do some reading
Sent from my SGH-T999 using Tapatalk
nitagro said:
I went from 4.3 stock to CM11 on my i747 but i didnt like the update. So i am trying to go back to 4.3 however whenever i try to install the 4.3 zip file thru twrp or CWM, it fails. As far as i know there is no odin file for going back. I tried to flash rogers 4.3 file through odin (thinking i would flash at&t modem later) but that also failed.
I would appreciate any help on how to install 4.3 once 4.4.2 has been installed on an i747
Click to expand...
Click to collapse
For One, you are on the wrong forum. This is for T-Mobile's S3 not AT&T. Second, Like @passtheknowledge said, you really need to do significant research and reading here on XDA.
Perseus71 said:
For One, you are on the wrong forum. This is for T-Mobile's S3 not AT&T. Second, Like @passtheknowledge said, you really need to do significant research and reading here on XDA.
Click to expand...
Click to collapse
I was up all night reading and trying all the suggestions that have been posted so far. Nothing worked. I would appreciate if someone can throw some light on what might be wrong.
nitagro said:
I was up all night reading and trying all the suggestions that have been posted so far. Nothing worked. I would appreciate if someone can throw some light on what might be wrong.
Click to expand...
Click to collapse
Please Read through this Thread. For Future Reference, all Odin Files for S3 in general are looked up by unique Keyword Root66. That thread is the right place for you to post errors or issues. If there's no 4.3 image for your phone there, you can post a request as well.
For your immediate Problem, there is a an alternate ATT StockMod Rom by @saranhai Please see this thread. Pay particular attention to the mandatory requirement of flashing a particular modem beforehand.
Hello, I am currently rooted and have CWM 6.0.4.3. installed. I'm on CM11 but want to go back to stock.. Is there an easy way to keep root and go back to stock. Want stock for a few functions that ROMS dont seem to be offering but can keep root and CWM ??
Thanks.
Which phone do you have? You could try flashing a pre-rooted stock ROM via Odin. Then use Odin to flash CWM.
Bt its better to firstly install ur stock rom and then again root it as it takes no longer than 5 mins
DeathNotice said:
Bt its better to firstly install ur stock rom and then again root it as it takes no longer than 5 mins
Click to expand...
Click to collapse
Ok perfect, thats what I was looking for. Phone btw is S3 - d2att - SGH i747) Sounds good to install the stock rom and re-root.. I'm sure its here but I have searched everywhere to find a tutorial on this and I cannot find a straight answer.
Would you mind giving me the steps or pointing me to a thread that explains how to and has the files in need to download ?
audit13 said:
Which phone do you have? You could try flashing a pre-rooted stock ROM via Odin. Then use Odin to flash CWM.
Click to expand...
Click to collapse
Do you know if there is a step by step on this somewhere ? I dont mind going back to complete stock.. I can just re-root and flash CWM after.
OR
Maybe you could just answer the bigger question : the reason I want to go back to stock is I need to use MHL/HDMI which CM11 doesnt support. I dont want to go back to stock, I would rather even go to another ROM that supports mhl/hdmi.. but if I have to go to stock, than so be it.?
Were you running the stock AT&T 4.3 ROM before you switched to CM11?
audit13 said:
Were you running the stock AT&T 4.3 ROM before you switched to CM11?
Click to expand...
Click to collapse
Yes, I bought the phone new and was running stock, Canadian Rogers version and had changed to CM10, then to 11.
robberrobbie said:
Yes, I bought the phone new and was running stock, Canadian Rogers version and had changed to CM10, then to 11.
Click to expand...
Click to collapse
Since you installed a custom recovery, that would have tripped the Knox counter which voids the warranty. It's not a problem if the phone is working properly.
Did you update to 4.3 or did it come with 4.3?
You may be better off installing a pre-rooted ROM.
http://forum.xda-developers.com/showthread.php?t=1739426
audit13 said:
Since you installed a custom recovery, that would have tripped the Knox counter which voids the warranty. It's not a problem if the phone is working properly.
Did you update to 4.3 or did it come with 4.3?
You may be better off installing a pre-rooted ROM.
http://forum.xda-developers.com/showthread.php?t=1739426
Click to expand...
Click to collapse
It was quite some time ago but I believe I was on ICS 4.0.. and switch to CM from there. Im not worried about the counter for warranty, that's expired on my unit anyways. I just want to be able to use MHL/HDMI function.. so if fine with flashing pre-rooted.. or stock.. or a different ROM that support MHL/HDMI. Can you recommend the easiest route ?
robberrobbie said:
It was quite some time ago but I believe I was on ICS 4.0.. and switch to CM from there. Im not worried about the counter for warranty, that's expired on my unit anyways. I just want to be able to use MHL/HDMI function.. so if fine with flashing pre-rooted.. or stock.. or a different ROM that support MHL/HDMI. Can you recommend the easiest route ?
Click to expand...
Click to collapse
I asked about 4.3 because the 4.3 bootloader cannot be downloaded. Flashing via mobile Odin will not touch the bootloader or modem.
You could try a pre-rooted rom and then flash a custom recovery via Odin.
I use Philz Touch from here: http://goo.im/devs/philz_touch/CWM_Advanced_Edition/d2att
audit13 said:
I asked about 4.3 because the 4.3 bootloader cannot be downloaded. Flashing via mobile Odin will not touch the bootloader or modem.
You could try a pre-rooted rom and then flash a custom recovery via Odin.
I use Philz Touch from here: http://goo.im/devs/philz_touch/CWM_Advanced_Edition/d2att
Click to expand...
Click to collapse
Ok thanks, I will do that. 1 thing I'm not quite sure of is the bootloader situation ? In the first tutorial there is a note : Flashing a prior bootloader can hard/soft brick your device. How do I know ?
I see the steps as:
Extract tar file you downloaded.
Use Odin, put phone into download mode [with phone off, hold vol. down + home + power ], connect to computer and open Odin.
once in odin click the PDA field and select the tar file
Leave Auto Reboot and F. Reset Time checked.
click start and when done let phone reboot.
If you just want a stock, rooted phone with no custom recovery, no plans to flash custom roms, etc. then you can stop HERE.
For my situation, is it just that easy ?
Before flashing, verify the version of your bootloader.
audit13 said:
Before flashing, verify the version of your bootloader.
Click to expand...
Click to collapse
OK I have made an effort to go read and figure out how to find out what version of bootloader on my own.. But i cannot find ? Any chance you know... And could help?
You mentioned your have the i747 and Rogers. Do you have the AT&T s3 (i747) or Rogers/Bell/Telus s3 (i747m)?
What is the most recent stock ROM you had on your phone?
Hey. I got the i747m. As for what was the last stock ROM I had, can't say. I know when I bought the phone it was ICS and I had received and update to jellybean.. But them went to cm10. The tutorial I followed told me had me back everything up, which I did. Have it in a file somewhere on my comp, would that tell me ?
Sent from my SAMSUNG-SGH-I747 using xda app-developers app
If you are flasjing back to stock you should flash back to the same baseband/bootloader that came stock on your phone.
I'm looking for a stock rooted zip for the sasktel i747m (MF1) that i can flash in CWM....I need to go back to stock to fix a data issue that ive encountered through flashing these new d2lte builds...
Does anyone know if a cwm flashable stock rooted rom exists for Sasktel's i747m with baseband MF1 ???I already have the Odin flashable stock rooted zip but don't have a laptop handy until tuesday....And im pretty sure i cant flash that zip in cwm recovery....
Sent from my SAMSUNG-SGH-I747 using XDA Premium 4 mobile app
Ariesdroid said:
If you are flasjing back to stock you should flash back to the same baseband/bootloader that came stock on your phone.
I'm looking for a stock rooted zip for the sasktel i747m (MF1) that i can flash in CWM....I need to go back to stock to fix a data issue that ive encountered through flashing these new d2lte builds...
Does anyone know if a cwm flashable stock rooted rom exists for Sasktel's i747m with baseband MF1 ???I already have the Odin flashable stock rooted zip but don't have a laptop handy until tuesday....And im pretty sure i cant flash that zip in cwm recovery....
Sent from my SAMSUNG-SGH-I747 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
I have not seen a stock mf1 ROM that can be flashed in CWM. You could use mobile Odin to flash back to stock and then flash Philz Touch via desktop Odin later.
OK, so back to my question.. If I have the i747M and bought the phone with ICS.. does this help.?
audit13 said:
You mentioned your have the i747 and Rogers. Do you have the AT&T s3 (i747) or Rogers/Bell/Telus s3 (i747m)?
What is the most recent stock ROM you had on your phone?
Click to expand...
Click to collapse
Hey there Audit, Sorry to bother you again, I just dont know how to move forward from here and neeeeeed some help.
I have been reading for days and days have not found a straight answer for my issue and I dont want to just go ahead and start flashing when I dont know if its the right method ?
I dont know how to get back to stock from where I'm at, I dont know how to figure out what bootloader I have (you asked me)
I have found a couple links on XDA that I can follow, I'm just not sure if they apply to my situation ?
This is a pretty detailed response/tutorial, but I dont know if I can just go ahead with this or not ?
http://forum.xda-developers.com/showthread.php?t=2186967
This is also very detailed: http://forum.xda-developers.com/showthread.php?t=1739426
Any help would be greatly appreciated !
robberrobbie said:
OK, so back to my question.. If I have the i747M and bought the phone with ICS.. does this help.?
Click to expand...
Click to collapse
If you are sure you have the Rogers i747m and you have never loaded a stock Rogers 4.3 ROM onto your phone, you could use desktop Odin to flash a pre-rooted 4.1.2 ROM from here: http://forum.xda-developers.com/showthread.php?t=1739426.
Flashing the pre-rooted 4.1.2 ROM will return the phone to completely stock, wipe out all installed apps and data, and you will have root. I do not recommend flashing the Rogers 4.3 pre-rooted ROM from the link.
Once you are able to boot into the phone and set things up, you can flash Philz Touch from Odin which will give you a custom recovery on a rooted stock 4.1.2 ROM.
hey can anyone help me? i've recently reverted my note 2 back to stock via odin and everything seemed fine. When the phone booted and i went through the setup process it always hangs. No matter what i do it always hangs. I've tried reflashing it and rebooting it over and over again but it always hangs. anyone know why this keeps happening?
Are you flashing the latest stock ROM? You're performing a factory reset before booting the ROM for the first time?
audit13 said:
Are you flashing the latest stock ROM? You're performing a factory reset before booting the ROM for the first time?
Click to expand...
Click to collapse
Yup latest stock rom, and before i flashed via odin i deleted my previous rom via twrp and formatted internal storage so its 100% clean
I've downgraded a Note 2 sgh-i317m to 4.1.1 from 4.4.2 by flashing a stock 4.1.1 ROM from sammobile.com in order to network unlock the phone. Flashing the stock 4.1.1 ROM tripped knox and could be installed via Odin because the 4.1.1 ROM from sammobile.com did not contain a 4.1.1 bootloader so I wound up with a stock 4.1.1 ROM on a 4.4.2 bootloader. After unlocking, I flashed the stock 4.4.2 ROM again and the the phone worked as it should.
I'm not sure which phone you have and I'm not sure downgrading and upgrading will work in your case but it's something you may want to look into.
audit13 said:
I've downgraded a Note 2 sgh-i317m to 4.1.1 from 4.4.2 by flashing a stock 4.1.1 ROM from sammobile.com in order to network unlock the phone. Flashing the stock 4.1.1 ROM tripped knox and could be installed via Odin because the 4.1.1 ROM from sammobile.com did not contain a 4.1.1 bootloader so I wound up with a stock 4.1.1 ROM on a 4.4.2 bootloader. After unlocking, I flashed the stock 4.4.2 ROM again and the the phone worked as it should.
I'm not sure which phone you have and I'm not sure downgrading and upgrading will work in your case but it's something you may want to look into.
Click to expand...
Click to collapse
I've managed to get the phone working (N7100) and it seems to run fine on Nougat. I did some testing and indeed it would always crash on setup with kitkat roms. I wonder why this is the case....
It is strange that kit kat causes a problem.
Have you tried using a different version of twrp to wipe the system before flashing with Odin? Can't think of anything else that may solve the problem.