Related
OK, so I dropped my phone and the LCD went out, I hooked the phone up to the laptop and the phone still works fine, even the touch screen works. ( I used My MObiler to see phone screen on the pc).
I bought a new LCD screen off of Ebay and replace it, now, the LCD screen works, but for some reason, the touch screen stopped working.
When I took the LCD apart from the touch screen, there seem to be a layer of grease of some sort between the touch screen and the LCD. I wiped it off with a lens cloth, don't know if that caused any problem.
Also there is a dark film (tinted) glued to the touch screen when looking from the back, what is that for? I looked at replacement touch screen on Ebay but none of them have the tinted film layer. I've search all over the internet for instructions but can't find any.
So my question is, what are the correct procedures for replacing the LCD screen and the touch screen (digitizer) ? Also after I installed the new LCD screen, the screen is very reflective and the glare is really bad, how do I fix that problem?
Thank you experts!!
You should have replaced both the LCD screen and the Digitizer. There are complete kits on ebay as well as instructions/tools to complete the replacement. Did you purchase the digitizer also?
bojangle said:
You should have replaced both the LCD screen and the Digitizer. There are complete kits on ebay as well as instructions/tools to complete the replacement. Did you purchase the digitizer also?
Click to expand...
Click to collapse
I went ahead and purchased the digitizer by itself after the original stopped working. Hopefully, it will get my phone back to normal. Thanks for your reply!
in the wiki theres disassebly instructions of the device that should help you (but you probably already know that since you've already switched out the LCD)
In my experience, i have never replaced either the digitizer, or the LCD by themselves, i've always bought LCD+Digitizer and replaced them as one. Seems like the Digitizer is usually glued onto the LCD and i never wanted to mess with that.
fone_fanatic said:
in the wiki theres disassebly instructions of the device that should help you (but you probably already know that since you've already switched out the LCD)
In my experience, i have never replaced either the digitizer, or the LCD by themselves, i've always bought LCD+Digitizer and replaced them as one. Seems like the Digitizer is usually glued onto the LCD and i never wanted to mess with that.
Click to expand...
Click to collapse
I should have ordered the kit instead of just the LCD. What lead me to order just the LCD is when I hooked the phone to my pc and confirmedthe digitizer still worked. And since this is the first time ever I disassemble a phone, I assumed the two things were separated.
But my digitizer should come in tomorrow so I'll just have to wait and see. Thanks for the info.
where did you find a guide to take apart the TP2? I just had the unfortuante luck of smashing mine in the car door as I got in....it fell out of my pocket the exact moment i was closing the door....
My screen is shot, but other than that the device appears to work. I can power on, and try to dial after I press the hard key for the phone pad. The touch portion seems to work, but from your luck, I guess I am looking at having to replace both...
anyhow...any advice on guides and how to find the stuff on the ebay would be apperciated.
I still have 18 months of a 2 yr contract....sucks....and it sucks doubly becuase i just took the insurance off last month....grr..
forcemac said:
where did you find a guide to take apart the TP2? I just had the unfortuante luck of smashing my in the car door as I got in....it feel out of my pocket the exact moment i was closing the door....
My screen is shot, but other than that the device appears to work. I can power on, and try to dial after I press the hard key for the phone bad. The touch portion seems to work, but from your luck, I guess I am looking at having to replace both...
anyhow...any advice on guides and how to find the stuff on the ebay would be apperciated.
I still have 18 months of a 2 yr contract....sucks....and it sucks doubly becuase i just took the insurance off last month....grr..
Click to expand...
Click to collapse
Here's a photo guide of the disassembly of a Rhodium (TP2), it might give you some insight. There's also been a number of threads in this section about hardware parts and the screen/digitizer in particular, listing places where people found/ordered replacement parts.
forcemac said:
where did you find a guide to take apart the TP2? I just had the unfortuante luck of smashing mine in the car door as I got in....it fell out of my pocket the exact moment i was closing the door....
Click to expand...
Click to collapse
The disassembly instructions are here: http://translate.google.co.uk/trans...ka/htc_touch_pro2/&sl=ru&tl=en&hl=en&ie=UTF-8
I did not follow those instructions since I did not want to open the back of the phone.
What i did was I tilted up the phone and used a very small screwdriver and unscrewed the two screws from an angle (it worked).
Then I pried the back of the tilting part of the phone all around to reveal the inside. Be careful not to pull too hard on the flat cable since it's still attached to the back (body) of the phone.
The LCD and touch screen are glued together (I didn't know that before). At this point I would remove the tape that is attaching the flat cable to the back of the LCD, and also lift up the clear yellow tape and detach the three connections.
The widest ribbon is from the LCD, the medium one is for the 4 hard buttons in the front, and the little one is for the touch screen.
I would suggest wearing some sort of anti-static wrist strap (I think I fried my touch screen along with the flat ribbon that is attached to the phone while trying to replace the LCD without anti-static wrist strap).
Once the whole tilting part is freed from the phone, I would carefully push the whole screen (digitizer + lcd) out from the frame, again, they are glued to the frame but can be removed fairly easy.
That's it, the install is reversed of removal and hopefully yours will work again.
Like I said, I think I fried my flat ribbon so after replacing the Digitizer (it came in today), the touch screen still doesn't work, so now I'm looking for that part, I'd appreciate a link to it if anybody knows where to get one.
Oh, and for the parts, just do a search on ebay for "touch pro 2 lcd" or touch pro 2 lcd + digitizer"
Gook luck with your phone!
What tape to use to stick digitizer back to inner bezel/chassis?
Hi - i got as far as trying to replace my Digitizer only to find that the LCD was stuck to it too. So as clever as i am (not) - i tried to remove the LCD off the digitizer - but that just ended up cracking it.
So i'm in the process of ordering a LCD with the digitizer - pre-stuck together (i hope!) - but my question is:
When i removed the digitizer off the front bezel, there was this spongy sort of double sided tape... i assume it was used for a reason and not just any ordinary double sided tape (presumably to allow a bit of leway between the digitizer and the bezel when pressure is applied to the touch screen)...
Any thoughts on what sort of tape this is? - here's some photos of my digitizer and the bezel:
zedii.co.uk/DSC_0002.JPG
^some of that tape is left on the digitizer... it's the black spongy stuff...
zedii.co.uk/DSC_0003.JPG
^i cleaned (removed residue of sticky tape) in the inner part of the bezel where the digitizer would stick...
Any specific tape to use that anyone knows of?
zedii said:
Hi - i got as far as trying to replace my Digitizer only to find that the LCD was stuck to it too. So as clever as i am (not) - i tried to remove the LCD off the digitizer - but that just ended up cracking it.
So i'm in the process of ordering a LCD with the digitizer - pre-stuck together (i hope!) - but my question is:
When i removed the digitizer off the front bezel, there was this spongy sort of double sided tape... i assume it was used for a reason and not just any ordinary double sided tape (presumably to allow a bit of leway between the digitizer and the bezel when pressure is applied to the touch screen)...
Any thoughts on what sort of tape this is? - here's some photos of my digitizer and the bezel:
Any specific tape to use that anyone knows of?
Click to expand...
Click to collapse
I wish you had asked before you ordered the digitizer + LCD, since I ordered mine separately, and they seem to both working ok. The digitizer does not have to be glued to the LCD. But anyway, I just used plain old Gel superglue to glue the digitizer to the bezel. I used Gel superglue so it won't run into the electronics beneath. Things seems to work just fine now.
One thing to consider when you crack open the whole phone though. Be careful not to loose any part from within the phone, because apparently, I lost something, now my accelerometer doesn't work, and my screen doesn't rotate when you slide out the keyboard. Hope it works out for you!
adp9626 said:
I wish you had asked before you ordered the digitizer + LCD, since I ordered mine separately, and they seem to both working ok. The digitizer does not have to be glued to the LCD. But anyway, I just used plain old Gel superglue to glue the digitizer to the bezel. I used Gel superglue so it won't run into the electronics beneath. Things seems to work just fine now.
One thing to consider when you crack open the whole phone though. Be careful not to loose any part from within the phone, because apparently, I lost something, now my accelerometer doesn't work, and my screen doesn't rotate when you slide out the keyboard. Hope it works out for you!
Click to expand...
Click to collapse
Thanks for the advice adp9626! Well in summary I think I've just been messing about too much and being stupid really.
In the end, I managed to just remove the top part of the screen without actually having to break into the bottom section of the phone.
I was a bit concerned about the whole sticking of the LCD to the Digitizer part. I actually did purchase them separately, however I was not sure what kind of glue was used to stick them both together - as I recall it was a nightmare to try and remove the LCD off the old Digitizer.
So I returned both separate parts (got a full refund as I didn't use them) - and now I am looking to purchase both parts stuck together.
I'm waiting on the guy on eBay to confirm that they are both stuck together. I'm also thinking of using double sided sticky tape to stick the Digitizer back to the inner bezel...
So that's the final plan! I've been a bit silly in rushing with ordering parts etc. but I just want to be on the safe side now - well - at least with the LCD stuck to the Digitizer part.
I will take your advice on the gel superglue if the double sided sticky tape doesn't prove it's stickyness!
Thanks
Zayd.
Can anyone help me find the lcd screen and digitizer as a single unit for Sprint? Everyone I find states not for CDMA.
Thanks
Anyone ??? I spent an hour on google and still came up with no leads.
hyghlndr said:
Anyone ??? I spent an hour on google and still came up with no leads.
Click to expand...
Click to collapse
I ordered one from this guy and it works great. it comes with the entire top half of the phone and the keyboard. There is only one left so you may want to hurry. Link: http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&Item=270583335455&Category=20336&_trkparms=algo%3DLVI%26its%3DI%26otn%3D2
Edit: I wanted to add that they're are slightly used so there will be scratches. The one i received is a little more scratched than my original then again the scratches aren't noticeable when the back light is on and you're getting a working screen.
Just my experience, I had a faulty LCD, digitizer was OK. Bought a replacement LCD off ebay, delivered from China but only cost me £20 inc delivery. Arrived with tools as well (T5, T6, philiips, and pry tool). Followed a couple of disassembly instructions online, took me a while to get all apart but managed it. None of the instructions online go through actually taking the screen out, I thought I'd messed it up as I took the back half of the LCD off and left the front bit on, and I couldnt get it off at first. I ended up using a very sharp scalpel to slide between the LCD and digitizer and got them apart eventually, as I didnt realise that they were glued.
Anyway, I just placed the screen on, no glue as there is a ring of sticky tape around the back of the digitizer which holds the screen in. Connected everything back in the end and its working fine. Only prob is I think I damaged the power/standby button, so be careful when around this area.
Touch Screen not responding after replacement
Recently, I replaced a glass screen on a SGH-M919 Galaxy S4. Previously, during the process of cleaning the glue residues off the LCD screen; I rubbed it with rubbing alcohol and it removed a small streak of the adhesive glue off left side of LCD screen and bottom right corner. After installed the new glass screen, I noticed a few spots of the glass screen wasn't sticking onto the sticky layer. So it looked like it has big air bubble between the glass screen and LCD. And I could see the rubbed off streak on the LCD screen. Everything worked fine with the new glass screen, with the exception of seeing the streak and bottom right corner rubbed off.
A few days ago, I had a table clock fell on top of the phone and broke a piece of glass. Nothing happened to the LCD screen and still functional 100%. So I got a replacement glass screen - the same as the first time replacement. With noticing of the rubbed off streak and corner of the adhesive layer on the LCD screen - I decided to rub off all of the adhesive layer from the LCD. I sprayed some Goof Off liquid on the adhesive layer and left it over night. Next morning I continued scraping off the glue with a small plastic card. Cleaned off all glue residues and examined the LCD screen for any scratches or damage. There was none. Re-installed new glass screen - but now the touch screen does not respond to the touching on the icons. Only the Home, Menu & Back touch button work. I was baffled after this.
Could it be that because I left some the Goof Off liquid on top of the LCD screen over night and it might have leaked to the other side and shorted out something? I saw a few forums that suggested a Factory Reset. I did that - but still didn't work. Please advise on what I need to do to fix this problem.
Thank you in advance for the advise or suggestion.
So you know that these are the TP2 forums, and no one has used this thread in the last 3 years....right?
LCD digitizer replacement.. now black screen
I saw the for replacing the LCD-digitizer of my nexus 4 phone, and followed the steps carefully. After I placed the battery, I checked to see if the phone turns ON and the display is working before I complete the last step of putting the back coverplate. I successfully switched it ON, saw a perfectly working screen, and browsed through my apps. To complete the assembly, I put the back cover by gently pressing the frame along the edges, but suddenly I saw some yellow green lines in the middle of the screen. I switched it off and again switched in ON, but now the entire screen had light with no display.
To fix this, I tried again checking all connections but no luck. What could be the reason for the sudden loss of display when it worked perfectly fine moments ago? Is there a possibility that I damaged the LCD while putting the back cover on the phone?
I am also not sure about one of the ribbon connectors of the digitizer. There are 2 big ones which are prominent and has ports to connect. However, there is a little third one which also has to come through the gap but doesn’t connect anywhere. Has anyone also experienced this while replacing the screen? Any help will be appreciated.
Hi guys,
I have just broken my Dinc2's glass screen. The underlying LCD screen is still functional and the touch screen works. So, I am guessing that I only broke the glass on the top of the screen... I uploaded pics to make it clear.
The casing near the USB port got bent some time back when I went kayaking... And I think that is where the screen cracked significantly when I dropped the phone.
I can still use the touchscreen and there are no discoloration on the LCD. So, can you guys suggest to me what Screen replacement product I need to buy online and (preferably) give me a link for said product and a How to repair guide. Plus, is this process easy? As in if I spend a few hours carefully following the steps to repair, will I succeed?? Moreover, can I replace the metal casing as well?
Thanks for the help gang! I really need to get my phone back to 100% working condition as I don't have an upgrade available till April '13 and I have cancelled my phone's insurance recently!
EDIT: Does this product help? http://www.amazon.com/gp/product/B0057OO9OC/
http://www.repairsuniverse.com/htc-droid-incredible-2-screen-replacements-repair-parts.html
I just replaced my digitizer for $11 on eBay.
It's an HTC one too (no "Verizon" branding, just "HTC".
It's for an Incredible S, came out of SoCal.
EDIT:
Here's the Digitizer
http://goo.gl/w7Vr0 $12.77
Here's the adhesive (sticker) that HAS to be replaced or it'll lift-up and will allow dust inside. Thus driving you F'ING INSANE. Mine is on order
http://goo.gl/34ylh
-Truckin-
Truckin'Ain't4Sissies said:
I just replaced my digitizer for $11 on eBay.
It's an HTC one too (no "Verizon" branding, just "HTC".
It's for an Incredible S, came out of SoCal.
EDIT:
Here's the Digitizer
http://goo.gl/w7Vr0 $12.77
Here's the adhesive (sticker) that HAS to be replaced or it'll lift-up and will allow dust inside. Thus driving you F'ING INSANE. Mine is on order
http://goo.gl/34ylh
-Truckin-
Click to expand...
Click to collapse
So I have dust under my screen even though my phone is completely original and never been dropped. Do you think it's worth taking apart, cleaning out, and replacing the adhesive? How long do you think it would take, and what is the likelihood of doing more damage to the phone?
Truckin'Ain't4Sissies said:
I just replaced my digitizer for $11 on eBay.
It's an HTC one too (no "Verizon" branding, just "HTC".
It's for an Incredible S, came out of SoCal.
EDIT:
Here's the Digitizer
http://goo.gl/w7Vr0 $12.77
Here's the adhesive (sticker) that HAS to be replaced or it'll lift-up and will allow dust inside. Thus driving you F'ING INSANE. Mine is on order
http://goo.gl/34ylh
-Truckin-
Click to expand...
Click to collapse
I bought the following on amazon:
http://www.amazon.com/gp/product/B005GIUHDQ
http://www.amazon.com/gp/product/B0057OO9OC
http://www.amazon.com/gp/product/B002EXHR1Q
I should have probably waited for more replies, like yours, here to get a better product link. Anyway, I guess I bought all the needed parts. I hope I get good quality material and I can get going with the repair... Do you think that they are good? The digitizer and tools didn't ship yet, so I can try and cancel and buy the one from ebay...
I actually just finished doing this a few hours ago. It does take some time to do it but if you have patience you can do it
You have to remove the LCD to remove the digitizer, so you will have all the parts out of the body of the phone. It is easier if you replace the body because it comes with new adhesive already perfectly cut and installed. If you reuse the old one you will have to scrape all the old adhesive off, then cut new adhesive. They are also available in red/silver/black so you can change colors.
Dermen said:
I actually just finished doing this a few hours ago. It does take some time to do it but if you have patience you can do it
You have to remove the LCD to remove the digitizer, so you will have all the parts out of the body of the phone. It is easier if you replace the body because it comes with new adhesive already perfectly cut and installed. If you reuse the old one you will have to scrape all the old adhesive off, then cut new adhesive. They are also available in red/silver/black so you can change colors.
Click to expand...
Click to collapse
When you say replacing the body, are you referring to the front housing/bezel? That is this: http://www.repairsuniverse.com/htc-droid-incredible-2-front-housing-bezel-replacement.html
If so, where did you buy it, as I want a reliable and reasonably priced product online. Thanks a lot for the help, btw!
litetaker said:
When you say replacing the body, are you referring to the front housing/bezel? That is this: http://www.repairsuniverse.com/htc-droid-incredible-2-front-housing-bezel-replacement.html
If so, where did you buy it, as I want a reliable and reasonably priced product online. Thanks a lot for the help, btw!
Click to expand...
Click to collapse
That is what I was referring to as the body, since all the parts attach to it. I actually got an entire new housing, came with the bezel, the middle part, and a new battery cover since my battery cover was beat up and I was changing colors. The middle part I didn't need but it was cheaper to buy all 3 parts than just 2.
I got it on ebay. The Incredible 2 and the Incredible S housing parts are interchangeable. I ended up getting S parts because they were cheaper. Most of the ebay sellers are in China so shipping takes 1-2 weeks depending on the seller. Repairsuniverse is good if you want it fast, I ordered from them once and got the part in 2 days.
Parts arrived. Links to tutorials PLEASE!
Dermen said:
That is what I was referring to as the body, since all the parts attach to it. I actually got an entire new housing, came with the bezel, the middle part, and a new battery cover since my battery cover was beat up and I was changing colors. The middle part I didn't need but it was cheaper to buy all 3 parts than just 2.
I got it on ebay. The Incredible 2 and the Incredible S housing parts are interchangeable. I ended up getting S parts because they were cheaper. Most of the ebay sellers are in China so shipping takes 1-2 weeks depending on the seller. Repairsuniverse is good if you want it fast, I ordered from them once and got the part in 2 days.
Click to expand...
Click to collapse
Hi guys, I just received all the parts. The following are what I ordered:
Housing Front for HTC Droid Incredible 2 Red Body Frame Chassis Bezel Part
Verizon HTC Droid Incredible 2 Replacement Touch Screen Digitizer Replacement Front Glass
2mm Wide Double Sided Layer Adhesive Sticky Tape Sticker
Tools for iPhone and most of phone
Now I am ready to replace the screen. Tutorials? I found some online, but would like to see what you guys followed to see if I can find simple and comprehensive tutorials!
Thanks! And wish me luck.
litetaker said:
Hi guys, I just received all the parts. The following are what I ordered:
Housing Front for HTC Droid Incredible 2 Red Body Frame Chassis Bezel Part
Verizon HTC Droid Incredible 2 Replacement Touch Screen Digitizer Replacement Front Glass
2mm Wide Double Sided Layer Adhesive Sticky Tape Sticker
Tools for iPhone and most of phone
Now I am ready to replace the screen. Tutorials? I found some online, but would like to see what you guys followed to see if I can find simple and comprehensive tutorials!
Thanks! And wish me luck.
Click to expand...
Click to collapse
1. Take it apart.
2. Put it together with new parts.
3. ???
4. Profit.
prototype7 said:
1. Take it apart.
2. Put it together with new parts.
3. ???
4. Profit.
Click to expand...
Click to collapse
Thanks, captain obvious!
I wanted to know if there is a detailed how to. Anyway, managed to take it apart. All guides end at taking it apart and say, "well, now you know how to dissemble it, just go in reverse and assemble it. Well. I wish they don't do that and show me through the reverse just to avoid mistakes. I remember having to redo IKEA furniture due to missing a few parts. Don't wanna do this messy procedure and realize I forgot a button or worst still putting the screen on!
Anyway, I am a grad student with a bachelors in Engineering... I should be ashamed if I can't do this! :silly:
repairsuniverse has a guide on youtube for replacing the digitizer. I found it easy to follow. Only difference is when you put it back together put the parts in the new body. You will also have to pull the speaker out of the old body and put it in the new. It is held in by glue, heat it with a hairdryer/heatgun and it comes out pretty easily. You might need to use some new adhesive on the speaker, I was able to pull the old adhesive out of the body in one piece using a hairdryer and some tweezers.
Dermen said:
repairsuniverse has a guide on youtube for replacing the digitizer. I found it easy to follow. Only difference is when you put it back together put the parts in the new body. You will also have to pull the speaker out of the old body and put it in the new. It is held in by glue, heat it with a hairdryer/heatgun and it comes out pretty easily. You might need to use some new adhesive on the speaker, I was able to pull the old adhesive out of the body in one piece using a hairdryer and some tweezers.
Click to expand...
Click to collapse
I am 100% done with the repair. But there are a few issues. The Vibrator motor seems to be not working. Then, the Digitizer I bought doesn't have a hole for the front facing camera! That is not a major setback as I rarely use it and I have a tablet and a PC to skype chat with... But it is sad that a feature is missing.
The big issue is the vibrator not working. I didn't mangle it and put it back in place as I am supposed to. Finally, I have 1 or 2 small dust particles under the screen and that is ok. I couldn't remove all the dust and it is a miracle I managed to get it that clean. Finally I seem to have a slight green tint/screen bleed at top left corner. I didn't have that before and I didn't distort the LCD while replacing. Is it due to a smudge on the LCD there? I suppose it is a minor issue and not something that will amplify as I have a Transformer prime that has screen bleeds and it is apparently because the screws are too tight.. So may be I tightened something too much? Anyway, if it doesn't deteriorate I am ok, as it is a very, very minor problem.
So, bottom line: Main problems > (1) No FFC (due to improper digitizer) -> I don't intend to fix it. (2) Vibrator motor not working.
Can someone help me with 2?
I fricking fixed it! I have WORK to do and I spent about 4 hrs fixing my phone!!! I'm kinda screwed for tomorrow! At least now my phone works...
That is odd it didn't have a spot for the front camera. I replaced my digitizer and it has a clear spot for it but it is not even close to centered. It actually looks like it would obstruct the camera but it doesn't. If you take it apart again for some reason you can scrape the black off the back so it is clear. However, it is very hard to do that and make it look decent.
Getting it perfect with no dust between the lcd and digitizer is very very hard to do. The first phone I did I actually took it apart again because there not only was dust but smudges on the other side of the digitizer. As for the bleeding I wouldn't think you could cause it from pressure in the inc2 because the lcd and digitizer are just held on the front by adhesive. The LCD has adhesive around the entire edge of it, I don't know if that also blocks light from the edges but if it does and there is a little bit missing maybe it is the cause.
Dermen said:
That is odd it didn't have a spot for the front camera. I replaced my digitizer and it has a clear spot for it but it is not even close to centered. It actually looks like it would obstruct the camera but it doesn't. If you take it apart again for some reason you can scrape the black off the back so it is clear. However, it is very hard to do that and make it look decent.
Getting it perfect with no dust between the lcd and digitizer is very very hard to do. The first phone I did I actually took it apart again because there not only was dust but smudges on the other side of the digitizer. As for the bleeding I wouldn't think you could cause it from pressure in the inc2 because the lcd and digitizer are just held on the front by adhesive. The LCD has adhesive around the entire edge of it, I don't know if that also blocks light from the edges but if it does and there is a little bit missing maybe it is the cause.
Click to expand...
Click to collapse
The following are the images of my fixed and "pimped" Dinc2.
https://www.dropbox.com/s/beop9oqvn6qo9p5/2012-09-25 00.23.03.jpg
https://www.dropbox.com/s/qh62damm82z0qmu/2012-09-25 00.22.32.jpg
Is the two tone color combination looking sweet, or should I change the back to red as well? I have a spare black back cover. If anyone has a spare red back cover, I can trade!
Plus, the "smudge/screen bleed" at the top left edge is seen in this pic:
https://www.dropbox.com/s/illeve11tomyrtw/2012-09-25 00.54.23.jpg (The black spot on the middle of the left side is a dust spec!)
Close up: https://www.dropbox.com/s/9ys4r2e6xmxfhnh/2012-09-25 00.54.48.jpg
Is the smudge bad? I think it is just a smudge on the LCD and not a damage to the LCD right? In that case, I am cool, as I most likely will cause other smudges if I attempt to redo it anyway. Plus, I am kinda bummed out about the lack of FFC, but I hardly use it and the whole process of removing the screen is SOOO tedious (and I don't have a heat gun, so had to put my phone a feet above a gas burner! ) and it was so painful and stomach wrenching to safely remove the LCD/digitizer that I don't wish to do it again to repair the FFC...
So, what do ya say?
I think the two tone looks good since the red phones have all black accents. I thought it was weird that the speaker on the red phone is silver, while all the other accents are black.
There seems to be a problem with the adhesive. The digitizer is raised by about 1 millimeter at the top while it is attached better at the bottom. I think it is because I had an additional horizontal strip of adhesive at the bottom to attach the digitizer to both the LCD and the buttons firmly while I didn't put such a horizontal strip at the top as I didn't see one when I dissembled it. If I put pressure on the digitizer for a while, it sets back in place for about half a day. Is this a serious problem? I don't feel like dissembling again.
litetaker said:
Hi guys, I just received all the parts. The following are what I ordered:
Housing Front for HTC Droid Incredible 2 Red Body Frame Chassis Bezel Part
Verizon HTC Droid Incredible 2 Replacement Touch Screen Digitizer Replacement Front Glass
2mm Wide Double Sided Layer Adhesive Sticky Tape Sticker
Tools for iPhone and most of phone
Now I am ready to replace the screen. Tutorials? I found some online, but would like to see what you guys followed to see if I can find simple and comprehensive tutorials!
Thanks! And wish me luck.
Click to expand...
Click to collapse
I just broke my screen and im looking to go the same route. This is a good phone to have as a back up after i get my upgrade and i dont want to get rid of it.
Anyway, did you need all those parts to successfully change your screen? I thought if you bought a new housing you would not need the adhesive tape?
So, I shattered the glass on my Galaxy S3 today. It's pretty messed up (see the attached picture), but the touch works, even in the damaged areas. So it seems it's only the glass that needs to be replaced, with something like this:
http://www.ebay.co.uk/itm/Blue-Fron...K_Replacement_Parts_Tools&hash=item417515ee67
Correct?
Yep, goodluck. Replaced the same on my Galaxy Note 2. all good now.
Yeah.... if i were you and have the funds, I would replace the complete assembly ($100-$150 on ebay) and be happy.
I shattered the screen on mine and replaced the digitizer alone and now the screen has freezing/unresponsive issues. I should of known better and replaced the complete assembly, I got what i payed for, literally less than that actually. Now i have a semi-new gs3 collecting dust until i save up for a complete lcd.
1slow4G said:
Yeah.... if i were you and have the funds, I would replace the complete assembly ($100-$150 on ebay) and be happy.
I shattered the screen on mine and replaced the digitizer alone and now the screen has freezing/unresponsive issues. I should of known better and replaced the complete assembly, I got what i payed for, literally less than that actually. Now i have a semi-new gs3 collecting dust until i save up for a complete lcd.
Click to expand...
Click to collapse
The screen seems to work fine, touch/responsiveness is working fine in the areas. I have no intention of spending the £100-120 on a complete new screen (again...). I'd rather save that for a Nexus 5.
I'll post again when I receive the part and it's been replaced.
MadsBen said:
The screen seems to work fine, touch/responsiveness is working fine in the areas. I have no intention of spending the £100-120 on a complete new screen (again...). I'd rather save that for a Nexus 5.
I'll post again when I receive the part and it's been replaced.
Click to expand...
Click to collapse
Mine was working fine with cracked digitizer as well. The problems started with new digitizer. Seems that when typing hard enough the digitizer touches LCD and causes to freeze up. Anyways, Good luck.
Sent from my neXus⁴ using Tapatalk 2
Actually the glass on an s3 is just that, glass. The digitizer is fused together with the LCD. However glass is glued to the LCD which can make it very difficult to replace. If you've never taken on the repair of a screen before then I would say you'll be more likely to break the LCD than not in your replacement of the glass. But again it is possible if you are very slow and very careful. As someone else mentioned though it's much easier to replace the whole assembly.
It didn't went well. I wasn't too carefull. In the bottom, the glass was too shattered, so when I tried to lift it, a piece with glue got stock and lifted the digitizer. So now that don't work. I'm not gonna spend £100-120 on a new digitizer, I'm gonna settle for my good old Nokia 6300i (and Nexus 7...) and wait for the Nexus 5.
I would wait for the n5.. gs3 is a dying trend already.
Its hard like everyone said , if your really gunna do it watch videos online and be prepared. If you know anyone that has done it successfully ask for help or tips
ouch didnt see u tried it already
the same happened to me on my wife's white sgs3 trying to be the savior of the day turned out to be an expensive digitizer replacement of $200 instead of the $8 glass replacement. I rushed the glass removal and cracked the lcd screen. I could have ordered one on ebay for $100 but wife needs the phone the next day so i decided to get it repaired locally.
Just replace the glass. A lot of care for changing it, but it is not so hard to do. I did it 2 weeks ago, and all is all right.
My 2 cents
bidibull14 said:
Just replace the glass. A lot of care for changing it, but it is not so hard to do. I did it 2 weeks ago, and all is all right.
Click to expand...
Click to collapse
Wanted to warn that changing the glass is not for everyone. It takes patience and zen. If you rush it, you will likely break LCD and spend even more $$$ that you would have otherwise. Also following notes:
1. Watch at least a couple of youtube videos before starting.
2. Heavy duty heat blower works much better than a hair dryer. Of course, don't go crazy, as it's possible to melt the phone with it
3. S III has a wire at the bottom (the one which goes to the buttons). If you damage it, you will need to replace whole LCD, there is [almost] no chance you will be able to fix this wire. So, always start removing glass starting with the top of the phone
4. Heavily cracked glass is hard to remove, as it crumbles. To make it easier, a) put a scotch tape on top of glass, so that the small pieces stick to it, and b) use a lot of heat
5. Everybody advises to use plastic tools, personally I used swiss army knife with high level of success, and never had a problem scratching LCD. Your mileage may vary, but using metal blade certainly makes life much easier, especially in heavily cracked glass situation.
6. If you do use blade, it often is enough to get blade just a little bit under a glass, and then simply apply heat. Big chunks will unglue all by themselves.
7. Remember, that failure is always an option. Don't use it on the phone, if you know that you desperately need it working right this day, if you don't have a plan B.
1slow4G said:
Mine was working fine with cracked digitizer as well. The problems started with new digitizer. Seems that when typing hard enough the digitizer touches LCD and causes to freeze up. Anyways, Good luck.
Sent from my neXus⁴ using Tapatalk 2
Click to expand...
Click to collapse
same freezing issue on mine... apparently the hardness of Gorilla2 is much greater than the knockoff glass replacements. The replacement glass on ebay and kijiji may not be authentic and that is why it bends slightly when pressed harder (in fact mine cracked completely when I applied too much pressure)
i replaced my glass too (about month ago), and discovered that , the "freezing issue" come's when you press too hard.. that the glass touches lcd.
after quick google-ing , i've found that they suggest to apply uv glue (octa glue) , to fix that.
have somebody tried that ? is it worth that much effort to mess with liquid glue ?
hani93 said:
i replaced my glass too (about month ago), and discovered that , the "freezing issue" come's when you press too hard.. that the glass touches lcd.
after quick google-ing , i've found that they suggest to apply uv glue (octa glue) , to fix that.
have somebody tried that ? is it worth that much effort to mess with liquid glue ?
Click to expand...
Click to collapse
I've heard about that glue too. I'm considering switching mine, because when I repaired I reused the glue of the original glass, and know I had dust between the glass and the lcd -.-
My concern is about the uv light, don't know if we could put in the sun to substitute it.
I was researching how to replace the glass on an iPhone not too long ago and watched a video where the guy used the UV bonding agent. Long story short he said you can use sunlight to cure it but it takes substantially longer than using a UV lamp. I don't know exact time for sunlight but apparently it would work.
Also it appeared to be a long delicate process of removing the current glue from the digitizer and LCD without damaging it. But I'm sure anyone who has already replaced the glass knows how tedious the process is.
m1batt1 said:
I was researching how to replace the glass on an iPhone not too long ago and watched a video where the guy used the UV bonding agent. Long story short he said you can use sunlight to cure it but it takes substantially longer than using a UV lamp. I don't know exact time for sunlight but apparently it would work.
Also it appeared to be a long delicate process of removing the current glue from the digitizer and LCD without damaging it. But I'm sure anyone who has already replaced the glass knows how tedious the process is.
Click to expand...
Click to collapse
it's not that hard to remove factory gle there..
for example, i removed mine, by rolling the glue with fingers.
just make sure, that you don't apply too much pressure to lcd.
and after that, clean up lcd form dust/fingerprints, and you are good to go.
and for removing glass, i used usual/ stronger kitchen knife (attached picture).
i replaced my glass 3 months ago.
i use normal hair dryer to remove glass and glass comes out almost as whole except for small broken pieces.
i think my scratch guard help in that.
i didnt use any additional glue or uv light.
nonresponsive screen is issue but only when you press too hard and press of power button resolve this issue.
but whole process of replacing galss took 2hrs
I had my note 4 screen assembly replaced after I dropped it. However, the screen is no longer completely secured in the phone. The screen pushes into the frame if I place pressure on the screen and I can get my finger under the edge of the assembly on the top left corner. The home button is also loose, but gets tight like it should be if I hold the screen down. This is an annoying issue and I've recently noticed that dust is getting inside the phone, which I'm worried will cause hardware damage. The front camera is already blurry and cloudy from dust getting inside. If I take the screen off and apply new adhesive, will the screen sit in the frame like it should or is it impossible to restore the feel on a phone with a screen replacement to what it was like from the factory? I hope you hear from you guys, and thanks in advance.
I would take it to a local Sprint service and repair location (or where ever you got your screen replacement). They should be able to reseat your screen in the housing and clean your camera right up. In terms of applying new adhesive, you shouldn't really need to. The 15 some odd screws on the back should take care of it. Source: I'm a S&R Technician
Thanks for the help! My problem is that I'm hesitant to return to the shop where I got the screen replaced, because when they originally replaced it I was unsatisfied with how it fit so I went back and had them do some more work. It was alright at first, but it began to get steadily worse in a fairly short amount of time. So I'm a little cautious of going back there to ask them to do more work. If I asked them to reseat the screen assembly, do you think it would help? Also, is it possible to return to an almost-factory feel with a replaced screen or do I need to accept that the assembly will never be quite as tight as it originally was?
Similar issue
I had a similar issue and I took it back to sprint which they fixed regardless of my device being rooted.
Did you have the screen replaced before you took it to sprint, or was the screen loose from the factory?
you can find the replace guide at ifixit, I don't leave the link,you can google it.
If you want to buy original LCD screen ,you can go to the HCQS.
Anyone else have hairline cracks on the fold of the inner screen? Mine feel like they are on the screen protector, my screen display is fine. Anyone else experiencing this?
Talking to support now, supposed to take to an authorized repair place. They say it covered by warranty due to normal use causing the cracks. Being sent to an authorized Samsung repair place.
Just inconvenient.
Adhesive failure. Probably due to excessive stretching of the plastic protector during assembly.
blackhawk said:
Adhesive failure. Probably due to excessive stretching of the plastic protector during assembly.
Click to expand...
Click to collapse
Likely, but luckily it's covered by the warranty.
dirtybudha said:
Likely, but luckily it's covered by the warranty.
Click to expand...
Click to collapse
Did you end up getting this fixed under warranty? Mine did the same thing (and the entire screen protector along the fold ripped up all at once).
I did a chat and they told me to take it in to get it fixed, but I'm curious as to what they'll do.
Squeaky369 said:
Did you end up getting this fixed under warranty? Mine did the same thing (and the entire screen protector along the fold ripped up all at once).
I did a chat and they told me to take it in to get it fixed, but I'm curious as to what they'll do.
Click to expand...
Click to collapse
Squeaky369 said:
Did you end up getting this fixed under warranty? Mine did the same thing (and the entire screen protector along the fold ripped up all at once).
I did a chat and they told me to take it in to get it fixed, but I'm curious as to what they'll do.
Click to expand...
Click to collapse
Yes I did. They sent me to a certified repair shop.
They essentially replace the whole interior screen. The process worked, but the guys at the location were not that knowledgeable. We plugged it into a computer and it didn't see the USB access. Once I got it home, it worked on my computer. Who doesn't have the drivers for a device that they repair?
Anyway, it works great now.
That's good to hear it worked out for you. My inner screen also failed in the same manner with hairline fractures and black line down the middle turning it in to a Microsoft Duo. I've been on the phone with Samsung three separate times and have had nothing but resistance from them. They sent me to a local repair shop and the manager told me I must have gotten a piece of sand in the hinge or something....huh? He said go ahead and start a claim, but the final word was with him. He also said he got rid of his Fold 3 because he didn't want the same thing to happen to him. So there's definitely a problem with some of the units out there. I'll be sending mine to Samsung soon. I have no confidence that Samsung will actually cover this under warranty in my case due to the treatment I've received from their customer service. It's upsetting.
What a bummer... I got my phone Sept 24, and now on March 24, I just noticed that I have a small crack right where the phone folds. I am going in to Verizon tomorrow. The "Samsung Care+" wanted me to send it in with $249... This is definitely a warranty issue.
I went to my local corporate Verizon store this morning. They will treat it as warranty and my replacement phone arrives tomorrow. The area manager was there, took pics of the screen, and the phone to document current condition (which I appreciate) before approving the swap. Plus she says they are monitoring how many come in like this. Mine wasn't the first. They suspect, like many here, that it's the screen protector. (I guess the Flip 3 has issues too, but my daughter has one that is so far so good).
Now, as long as Verizon doesn't declare my phone as "damaged" by me it will be a free swap. If not, they'll try to bill me. But the area manager agrees that it looks like a defect (and it really is a defect).
One last gripe: I guess I was too eager to get my Fold 3 to realize that the "protection plan" carries a potential $249 fee for a broken screen. Thank goodness this is a defect.
emtownsend said:
. They suspect, like many here, that it's the screen protector. (I guess the Flip 3 has issues too, but my daughter has one that is so far so good).
Click to expand...
Click to collapse
do you mean that they suspect the screen protector is broken or that the screen protector is causing the UTG screen to break?
The thought was that the screen protector is cracking, but not the screen. I've not lost any functionality over the area that is "cracked".
Yeah, when I ran my finger nail over the cracks it would snag. It was absolutely my screen protector...which is factory installed and therefore falls under the manufacturer.
Yes, I think this will be an issue. I don't think this will totally kill the market or much of the sales. My replacement is still going strong, and I haven't heard too many others experiencing the cracks.
I'm sure the Fold 5 will have it all together. Hahaha
100% screen protector, I just replaced mine myself and small crack in the crease is gone!
Yeah, my nail would catch on it. At least it's not the screen...oy. That would be a nightmare.
Checked online, there is a few threads on the Sammy forums, and removing the inner screen protector does NOT void warranty. If the display/screen is damaged in the process, then iti is void.
My replacement protector, OEM, got it's first hairline crack. Gonna remove the OEM one and replace it myself. That way I can just replace it when it goes bad.
NOW I'll say I wouldn't recommend this phone to anyone because of this issue. Samsung failed here, but there's a chance to learn from it and improve it.
dirtybudha said:
Checked online, there is a few threads on the Sammy forums, and removing the inner screen protector does NOT void warranty. If the display/screen is damaged in the process, then iti is void.
My replacement protector, OEM, got it's first hairline crack. Gonna remove the OEM one and replace it myself. That way I can just replace it when it goes bad.
NOW I'll say I wouldn't recommend this phone to anyone because of this issue. Samsung failed here, but there's a chance to learn from it and improve it.
Click to expand...
Click to collapse
getting the same OEM Samsung screen protector was a bad decision and you should've known that already since it broke once. Samsung's screen protector is an ultra thin plastic layer that's why it breaks. I removed it myself and knew its nature. That's why I installed the Whitestone Dome Film instead (myself) and this protector is elastic and bends easily with the fold. You get definately no cracks because it's a film layer.
try it and you won't regret it. By the way it's so easy to install, and costs only $10- $15
A: How should I have known?? They could have replaced it with better materials.
B: Thanks for the insight into the Whitestone Dome.