Hello!
So i've been failing at getting this SGS4 SCH-M919 back to stock firmware. I have CM11 nightly installed. (This is my bosses phone that i'm trying to get back to stock) So far, I've downloaded two stock firmware images (just in case firs was corrupt) and they both haven't worked.
My process goes like:
-Download drivers (or Kies, i've tried both)
-Set into recovery mode
-Start Odin (i've tried in a few versions)
-Plug phone in
-Odin recognizes
-choose file to flash
-Start the flash then I'll always get this error
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> M919UVUAMDL_M919TMBAMDL_M919UVUAMDL_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> sbl2.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005> sbl3.mbn
<ID:0/005> rpm.mbn
<ID:0/005> aboot.mbn
<ID:0/005> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
After that, i'm in a little brick mode that I can easily get out of my flashing CWM Recovery on there, and it'll boot me back into CM11.
So, any ideas? I've tried two computers, restarted...idk what to do anymore.
Thank you to anyone who tries to help me!
Looks like you're trying to flash older firmware which will never work if the device has been updated to 4.3 and up.. You need to flash either 4.3 or 4.4.2. 4.3 will work if that was the firmware they had before flashing cm11.. Otherwise you need to flash 4.4.2
Sent from my SGH-M919 using Tapatalk
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I747UCDLK3_I747ATTDLK3_I747UCDLK3_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> aboot.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL! (Auth)
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
i hard brick, use sd card to boot, root, triangle away, boot to download, use odin for stock 4.1.1 gets to NAND write start and as u can see it fails, any fix for this?
EDIT: after the odin fail it goes back to showing SW REV CHECK FAIL : Fused 2 > Binary 0 on the download screen, thanks
You are getting errors because you are trying to load a ROM with an older bootloader. Your phone has a 4.3 bootloader which cannot be downgraded. Do not use Odin to flash any ATT ROM from sammobile.com.
Just load a custom recovery such as Philz Touch via Odin, wipe, and flash a custom Kit Kat ROM.
Ok, so yesterday i was trying to flash a custom rom on my Fame DUOS s6812i, the phone wasn't rooted or anything, so i did the process of rooting and everything via odin following the tutorial in this thread http://forum.xda-developers.com/showthread.php?t=2582851 and when i flashed the files for root and the recovery i got stuck in a bootloop, now i cant start the phone (obviously), i have no access to the recovery, all i can do is enter the download mode, So i tried to flash the stock firmware with odin and i keep getting this error:
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> S6812DDAMG3_S6812ODDAMG3_S6812DDAMF1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> boot.img
<ID:0/005> NAND Write Start!!
<ID:0/005> recovery.img
<ID:0/005> BcmCP.img
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
And in the screen of the phone shows twice this message : Secure: Signature Verification failed
Honestly i dont know what to do now, Kies just keep connecting and telling me to reset the phone, odin gives me this message, tried flashing kernel and recovery and it does not works, ive tried with 3 different firmwares from sammobile and the same. PLEAAAASSSEEEE! help me im kinda losing it over this and i dont know what to do.
are you install with the correct firmware ?
So I rooted my s4 mini i9195 and flashed aicp ver 10 and now I have no wifi, no mobile, no lte, the haptic feedback buttons don't work, no led, and my computer doesn't recognize the s4 mini unless I go into download mode. When I start up the phone it says something about something being wrong with the internal hardware of my phone but it's a brand new phone and I didn't have these problems before flashing this rom. I tried using odin to go back to stock and it fails at nand-write start. I tried loading a new pit and that fails too. I'm completely stuck now. I have no idea what to do. Can someone please help me?
How you flashed aicp?
I used cwm.
Here's what comes up on odin when I try to flash back to stock:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9195XXUCOD3_I9195BTUCOD1_I9195XXUCOD3_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> aboot.mbn
<ID:0/006> NAND Write Start!!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<ID:0/006> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Can you enter in recovery mode?
yeah, I can. I tried clearing caches and data and flashing aicp over again, it didn't work-in fact, for whatever reason the aicp rom isn't in my sd card anymore.
Try to flash a stock deodexed rom from here http://forum.xda-developers.com/showthread.php?t=2552363 using your custom recovery
the problem with that is I can't get anything from my computer to my phone because the phone doesn't pop up on My Computer and the phone doesn't give me any options when it's plugged in. It's only recognized when in download mode and trying to do anything in download mode doesn't seem to work.
Download direct to you phone and then move to sdcard or download to pc and than just using a card reader move rom to your sdcard and then try to flash
I can't download directly to my phone, I have no connection whatsoever on my phone.
Use a computer and a card reader ))
I'm going to get an sd reader later today. I tried flashing the modem and this is what I got:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MODEM_I9195XXUCOC2.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> NON-HLOS.bin
<ID:0/006> NAND Write Start!!
<ID:0/006> Transmission Complete..
<ID:0/006> Now Writing.. Please wait about 2 minutes
<ID:0/006>
<ID:0/006> Receive Response from boot-loader
<ID:0/006> Complete(Write) operation failed.
<ID:0/006> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
What firmware did you have before flashing aicp?
It was android 4.4.2 touchwiz I believe but I don't know the details. The phone was up-to-date and it's I9195
Whatever try to restore to a stock rom by flashing a deodexed rom
so the rom flashed properly but I still didn't have mobile data or wifi or haptic feedback. I'm not really worried about the haptic keys because I can just use softkeys if necessary but the mobile data and wifi are an issue. LED worked when I shut the phone down to put it into download mode to flash the modem. Flashing the modem was unsuccessful:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> MODEM_I9195XXUCOC2.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> NON-HLOS.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> Transmission Complete..
<ID:0/005> Now Writing.. Please wait about 2 minutes
<ID:0/005>
<ID:0/005> Receive Response from boot-loader
<ID:0/005> Complete(Write) operation failed.
<ID:0/005> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
And the phone came up with red lettered "Secure Check Fail Modem"
Try to call *#06# And tell what you get
At least look here http://forum.xda-developers.com/gal...rom-aicp-6-0-kk-4-4-4-9195-919015-10-t2907258
IMEI 990004400585315 / 01
I looked on that thread but nothing about my issue is coming up.
<ID:0/005> Receive Response from boot-loader
<ID:0/005> Complete(Write) operation failed.
Does this mean that I should flash a new bootloader? I never unlocked knox because beyond voiding the warranty, I didn't think it would have any effect on flashing but I may be wrong?
Your phone is definitely a "i9195" and not a "i9195L"? Was your phone locked to a network?
I found this http://forums.androidcentral.com/sa...ot-flash-really-really-stuck-please-help.html try to do how is described in the last thread but remember that you have a 9195 not a s3
So, I tried to remove my root from my Sprint Galaxy s6 via supersu and now I am in an infinite boot loop at the moment. I tried to install new firmware with Odin and I get the error :
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> G920PVPU1AOCF_G920PSPT1AOCF_G920PVPU1AOCF_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1005)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I am really out of ideas on what to do here really. Can someone help me. I can get into download mode and my model number is SM-G920P. I tried to remove the root because I did not know what I was doing with it but now looks like I need to learn more about it. Anything can help I just want to get on my phone.
That is an old firmware, try using the current one from here: http://forum.xda-developers.com/spr...uide-links-files-update-root-restore-t3366862
koop1955 said:
That is an old firmware, try using the current one from here: http://forum.xda-developers.com/spr...uide-links-files-update-root-restore-t3366862
Click to expand...
Click to collapse
I think that would be the one to fix it, downloading it now.
Thank you much, sir.