Tab 3 7.0 not charging in car - Galaxy Tab 3 Q&A, Help & Troubleshooting

I have a dual usb car lighter adapter that I use for charging all my devices while I'm in the car. For whatever reason my Tab will not charge when I plug it in. I also have a usb port on my stereo that I tried but it just went into mass storage mode with no way to get it to switch to charge only. Is there any way to fix this?

Strizay said:
I have a dual usb car lighter adapter that I use for charging all my devices while I'm in the car. For whatever reason my Tab will not charge when I plug it in. I also have a usb port on my stereo that I tried but it just went into mass storage mode with no way to get it to switch to charge only. Is there any way to fix this?
Click to expand...
Click to collapse
if im not mistaken, the tab needs at least a 2 amp power supply to charge. most usb chargers and usb ports only put out 1 amp or less.

Related

Forcing GN to charge in pogo pin dock with USB OTG in use

I have the official Samsung desktop dock for the GN with pogo pins for charging. I cut out a notch in the left side of the dock so that I could access the USB port on the phone when it's docked. I'd hoped I could then attach a USB OTG cable and mount a flash drive while the phone charged via the pogo pins.
Unfortunately, the two functions seem to be mutually exclusive. If the phone is in the dock and charging and I attach the cable and flash drive, they are not recognized by the phone. Or, if I attach the cable and flash drive first and mount the flash drive before placing the phone in the dock, charging doesn't initiate when I put the phone in the dock.
Does anyone know if there is some way via software or hardware to force pogo pin charging while a flash drive is attached and mounted via a USB OTG cable?
I will try tomorrow on my self built car pogo charger and usb otg. I have aokp with the fast charge override feature.
subvertz said:
I will try tomorrow on my self built car pogo charger and usb otg. I have aokp with the fast charge override feature.
Click to expand...
Click to collapse
Sounds great! Thanks much. If it works, it'll tempt me to go to AOKP myself.
Any luck on this?
I too want to use OTG functionality while charging phone in the official car dock.
USB OTG + charging
I'm actually trying to get the same get something like this going on a galaxy s2 (the I9100g with the omap processor) or a GN, My goal is to get usb host and charging going through the same cable. By making some changes in the kernel i've got the phone to think its in charging mode while in host mode, but if you check the battery status, it's still draining even though it says "charging" and I've got the a usb "Y" cable connected to a 5v 2amp power source.
I think cyanogenmod (there was a post on this here and a standalone app that eventually rolled into the latest cm7 nightly) has this working on a BN nook color (also TI-OMAP Processor), but I have not been able to verify this.
Does anybody have host+charing working on any device with an OMAP processor?
Sorry for the delay, I had an emergency work trip offshore on an oil rig. I can try it out tonight.
Results. Charging OTG killed pogo charging. I tried mounting in pogo charger with OTG already attached mounted with a basic thumb drive. Charging never started. I tried charging with pogo first, then plugging in OTG, charging stopped. I checked to make sure it was actually discharging by waiting for a few percent decrease.
Sorry, I was hoping it would work too.
subvertz said:
Results. Charging OTG killed pogo charging. I tried mounting in pogo charger with OTG already attached mounted with a basic thumb drive. Charging never started. I tried charging with pogo first, then plugging in OTG, charging stopped. I checked to make sure it was actually discharging by waiting for a few percent decrease.
Sorry, I was hoping it would work too.
Click to expand...
Click to collapse
Thanks for giving it a try. It would be interesting to know if this behavior is built into the hardware or could be modified via software/in the kernel. It's consistent with what happens when using a powered USB hub.
Other than a software mod, I'd sure like to see someone start making and selling an Accessory Charger Adapter as described in Chapter 6 of the USB Battery Charging Specification document from 2010. It's the exact thing needed to use USB OTG and charge at the same time.
Anyone knows if its possible to charge via USB, with a device connected?
I connect an adapter microUSB to USB OTG, than connect USB OTG in a USB HUB and than i connect a device in one USB and force in another, is it possible or not??
It may work, since connecting to the pc works.

OTG cable + power

Do i need a custom Kernel to get that capability?? I have a OTG cable that works for connecting a mouse, keyboard, thumbdrive etc and it has a port for power but the tablet does not recharge.
So i'm wondering if i need a custom Kernel or maybe the cable is defective or something.
If you know of one of those cables that work, please let me know.
Thanks in advance.
I have this cable out of China:
treetop777 said:
Do i need a custom Kernel to get that capability?? I have a OTG cable that works for connecting a mouse, keyboard, thumbdrive etc and it has a port for power but the tablet does not recharge.
So i'm wondering if i need a custom Kernel or maybe the cable is defective or something.
If you know of one of those cables that work, please let me know.
Thanks in advance.
I have this cable out of China:
Click to expand...
Click to collapse
I use a Otg Cable with an Usb Stick and a Usb Mouse,works fine with 4.4.2 and 4.2.2 with Stock Kernel
letschky said:
I use a Otg Cable with an Usb Stick and a Usb Mouse,works fine with 4.4.2 and 4.2.2 with Stock Kernel
Click to expand...
Click to collapse
And also charges simultaneously? That's what the OP is asking for.
Slimport adapter outputs HDMI signal and lets you charge the tablet simultaneously, but besides that... nothing else on stock ROM I imagine.
Iknownot said:
And also charges simultaneously? That's what the OP is asking for.
Slimport adapter outputs HDMI signal and lets you charge the tablet simultaneously, but besides that... nothing else on stock ROM I imagine.
Click to expand...
Click to collapse
Bummer! That's what i was afraid off.
Hello I have the same problem! : (
I installed the tablet in my car but you can not use the charger + OTG simultaneously.
You have to wait for someone to change the KERNEL as they did for the Nexus 7.
mannyy said:
Hello I have the same problem! : (
I installed the tablet in my car but you can not use the charger + OTG simultaneously.
You have to wait for someone to change the KERNEL as they did for the Nexus 7.
Click to expand...
Click to collapse
Nice setup! :good: That's exactly what i want to do. I can connect a mouse and thumb drive but no power. I was trying to work-out how to use a switch or relay or something to switch between otg and power but i haven't came up with anything yet.
treetop777 said:
Nice setup! :good: That's exactly what i want to do. I can connect a mouse and thumb drive but no power. I was trying to work-out how to use a switch or relay or something to switch between otg and power but i haven't came up with anything yet.
Click to expand...
Click to collapse
Hi everyone,
I had same problem!
My pad is rooted, 20b, stock kernel, Finally, find out solution.
I bought IBUFFALO usb with AC power around 15USD. 4 Slots for USB 2.0 and 1 double micro usb. Worked with mouse, Bluetooth keyboard, external drive with USB 2.0 only, usb 3.0 not work. Just for your info.
treetop777 said:
... I was trying to work-out how to use a switch or relay or something to switch between otg and power but i haven't came up with anything yet.
Click to expand...
Click to collapse
Difference between normal and OTG USB cable is that OTG has pins 4 (sense) and 5 (ground) shorted and on regular cable pin 4 is not in use. If you put a switch between these two pins you can switch between regular USB cable for charging and OTG for connected devices.
Some apps can be found on Google Play Store that claim to be able to switch between or enable simultaneous OTG and charging, but most are for specific devices or group of devices, none for G Pad 8.3. Most promising is maybe Faux123 Kernel Enhancement Pro (3.77€ and requires Root+Busybox+SuperSU).
Too bad our tablet has no secondary charging port (like Sony has magnetic charging port for example), but least intrusive would be to use powered USB HUB, let it power the connected devices so the battery drain on the tablet will stay low.
Iknownot said:
Difference between normal and OTG USB cable is that OTG has pins 4 (sense) and 5 (ground) shorted and on regular cable pin 4 is not in use. If you put a switch between these two pins you can switch between regular USB cable for charging and OTG for connected devices.
Some apps can be found on Google Play Store that claim to be able to switch between or enable simultaneous OTG and charging, but most are for specific devices or group of devices, none for G Pad 8.3. Most promising is maybe Faux123 Kernel Enhancement Pro (3.77€ and requires Root+Busybox+SuperSU).
Too bad our tablet has no secondary charging port (like Sony has magnetic charging port for example), but least intrusive would be to use powered USB HUB, let it power the connected devices so the battery drain on the tablet will stay low.
Click to expand...
Click to collapse
Thanks for that - Very good info! Allow me to pick your brain a little more: Looking at the cable i have (in the OP), do you think that by just connecting an external power (red and black) to the cable just before going into the tab would work somehow to give it power.
It's intreging what you said about being able to switch from regular USB (that can supply power) to OTG just by jumping those wires. I'm trying to picture something in my mind to accomplish what we want but the "light bulb" haven't came on yet - any suggestions?
I want to use the tab in the car PERMANENTLY so i need a way to charge it while behind the dash. I would want to use a mouse as well so OTG is a must.
In any case, i'm going outside right know to split open that cable and see how it's connected inside, maybe then the light bulb will come on in my head.
treetop777 said:
Thanks for that - Very good info! Allow me to pick your brain a little more: Looking at the cable i have (in the OP), do you think that by just connecting an external power (red and black) to the cable just before going into the tab would work somehow to give it power.
Click to expand...
Click to collapse
Try it out, you got the cables!
When pins 4 & 5 get shorted the tablet may be configured only to output power, not receive it. I have only OTG adapter cable and the supplied USB charging/data cable, so I cannot test this stuff.
treetop777 said:
It's intreging what you said about being able to switch from regular USB (that can supply power) to OTG just by jumping those wires. I'm trying to picture something in my mind to accomplish what we want but the "light bulb" haven't came on yet - any suggestions?
Click to expand...
Click to collapse
I would buy micro USB male plug, some heat-shrink tubing with glue, switch (3A) and split OTG adapter or HUB. Cut off the male plug fom the adapter, solder on the new plug to the adapter cable as normal USB, solder on the switch to pins 4 & 5 of the plug, check it for continuity and shorts, test it on the tablet, if good - secure the new plug to the cable with heat-shrink tubing.
EDIT: Possible solution with resistor described here
Our device, if it can be tricked this way, may require different resistor from the one used in the tutorial (usually in 36KΩ-200KΩ range).
Ok, I'm chopping it up! I spliced-in the red and black wires from a USB cable into the OTG cable (in the OP) and sure enough the tab gets power. However, it no longer detect the mouse or any thing else (kind of expected). Tomorrow i will try bridging pin 4 and 5 and see what happens. If that don't work, i will try the resistor. :fingers-crossed:
I have read that devices on OTG get polled regularly, but charging is not, i.e. if you start charging and after that short the pins 4 & 5, it will continue charging and you can use your OTG devices. Hope this holds true to the G Pad as well.
Isn't micro USB a "standard"....??
Then GEEZZ why do one manufacturer thinks it's ok to eliminate a pin completely! i assume that when i pay for that cable, i will get ALL 5 PINS even if one is not connected - rip-off! :laugh: This manufacturer not only didn't connect pin 4, it was eliminated completely; stopped me in my tracks! Fortunately, i have an extension that have of all things ALL 5 WIRES CONNECTED! Imagine that! But now, i don't have any time to chop-it-up until tomorrow. With the 5 wire cable, i will short the yellow and black wires but I'll check here first to see if I'm warned against it.
More to come..
Hi manny your car kooks awesome. I have one question. How you connect your speakers from the car with the G Pad. iam also interested to built a GPad in the car !
Sent from my GT-I9505 using xda app-developers app
Yep weneed more info on this as i would like to fit my pad in the van,, how did you get fm radio on there.
Nothing good to report. Connecting the power wire to the OTG cable and shorting the 4&5 pins does nothing different. I can have it charging and when i disconnect power, it then detects the mouse (that's a good thing) but when i plug the power back in, nothing happens! Ideally it would disconnect the mouse and start charging again but no-go. Having the 4&5 pins shorted or not makes no difference.
Still have a couple things i will try before i give up, one is the resistor and the other is a more simple OTG cable.
Will report back.
treetop777 said:
Nothing good to report. Connecting the power wire to the OTG cable and shorting the 4&5 pins does nothing different. I can have it charging and when i disconnect power, it then detects the mouse (that's a good thing) but when i plug the power back in, nothing happens! Ideally it would disconnect the mouse and start charging again but no-go. Having the 4&5 pins shorted or not makes no difference.
Click to expand...
Click to collapse
I understand that you would want the cables all hidden behind the dash in a car and can't be connecting and disconnecting plugs all the time, at the most just flip of a switch should make things work. The resistor trick would be ideal, if it works.
What's the exact sequence you did things in?
- Mouse and charger connected to the tablet simultaneously with pins 4 & 5 not shorted, tablet charging - short pins 4 & 5 - what happens?
- Only charger connected, pins not shorted, short pins and then connect mouse...
- Mouse and charger connected to the tablet simultaneously with pins shorted, mouse working - unshort pins...
- Only mouse connected, pins shorted, unshort pins and then connect charger...
Iknownot said:
I understand that you would want the cables all hidden behind the dash in a car and can't be connecting and disconnecting plugs all the time, at the most just flip of a switch should make things work. The resistor trick would be ideal, if it works.
What's the exact sequence you did things in?
- Mouse and charger connected to the tablet simultaneously with pins 4 & 5 not shorted, tablet charging - short pins 4 & 5 - what happens?
- Only charger connected, pins not shorted, short pins and then connect mouse...
- Mouse and charger connected to the tablet simultaneously with pins shorted, mouse working - unshort pins...
- Only mouse connected, pins shorted, unshort pins and then connect charger...
Click to expand...
Click to collapse
I would have to record in what sequence i do things to remember but it seem i have done every combination possible. I do remember doing these sequences after a fresh reboot of the tablet and BTW i made a simple cable out of a know working (single) OTG cable and splicing-in the red and black from the cable that has 5 wires connected, leaving the pin 4 wire disconnected and extending a pigtail from the black wire so i could short the yellow and black to hopefully force OTG:
- Power plugged in and mouse plugged-in then plug the cable into the tablet - it detects the mouse but does not charge.
- in the above state, shorted the yellow and black wire - no change.
- separated 4/5 then disconnected the mouse leaving power connected (expecting that the tab will then switch to charge but) - nothing. The mouse did disapear but the tab did not start to charge.
- shorted 4/5 (for ****s and grins) and as expected - nothing.
Again with a fresh tablet:
- with (ONLY) power connected to the cable, inserted the cable into the tablet - it started charging.
- in that same state, connected mouse - mouse was NOT detected but the tab continued to charge.
- with mouse plugged in, shorted 4/5 - no change (charging but no mouse detected)
THIS IS THE IDEAL SITUATION BUT JUST HALF WAY:
Rebooting the tablet with both power and mouse connected and cable inserted, the tab starts by accepting the charge (no mouse) but get this, plugging-out power makes the tab switch to the mouse right away! That would be good except that plugging the power back in does NOT make the tablet switch back to power, in fact, nothing happens, the mouse just continues to be detected.
If i had 2 cables, one only for power and the other only for OTG, i could pull one out and replace it with the other and both functions would work; i don't understand why that same "switching" can be recreated within one cable??
This is beyond me, the last thing i will try is following your sequences to the letter and with the resistor, if that doesn't work - i give up! :crying:
budalageo said:
Hi manny your car kooks awesome. I have one question. How you connect your speakers from the car with the G Pad. iam also interested to built a GPad in the car !
Sent from my GT-I9505 using xda app-developers app
Click to expand...
Click to collapse
i have buy a Sony mex bt4000U ... http://www.sony.it/support/it/product/MEX-BT4100U
install in rear a Tablet.. http://www.youtube.com/watch?v=5Y1QXAsSUtc
and work whith APP REMOTE http://www.youtube.com/watch?v=AEfG3Zdf7HM
---------- Post added at 11:02 AM ---------- Previous post was at 11:00 AM ----------
I have used this !!
have disassembly and install !!! work whit switch !!
http://www.ebay.it/itm/231182187439?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1439.l2649

Help with Otg

Hello i installed a nexus 7 in my car not i really dont want to take out my center console because its a huge Pita. But i realise that i now need an otg. I was runninh sound via bluetooth to my radio but the lag os crazy. I have acces to the the end of my charging cable. I was wondering would adding a usb to usb adapter and a usb hub. Would that be consider a usb otg cable. Would i be able to purchase a usb dac and use it. Also could i charge at the same time. I have absolutely no room to fit a audio jack on my tablet. So usb dac is my only option.
egren58 said:
Hello i installed a nexus 7 in my car not i really dont want to take out my center console because its a huge Pita. But i realise that i now need an otg. I was runninh sound via bluetooth to my radio but the lag os crazy. I have acces to the the end of my charging cable. I was wondering would adding a usb to usb adapter and a usb hub. Would that be consider a usb otg cable. Would i be able to purchase a usb dac and use it. Also could i charge at the same time. I have absolutely no room to fit a audio jack on my tablet. So usb dac is my only option.
Click to expand...
Click to collapse
You generally need a kernel installing to do as you have said eg elemental x or timurs. Yes, you can then use a usb otg cable to power and host the usb dac.

OTG Host and Charging Cable

Unfortunately, I just wasted over $30 on a Valarm IoT OTG Y cable. It does not work at all as a host cable for any USB device on the G4. I was hoping to use the Valarm cable to connect a USB DAC and charge the phone at the same time. The cable will let me charge the phone but whatever I connected to the USB female port is not recognized. If anyone finds a USB host cable that allows charging, please post!
mattnin said:
Unfortunately, I just wasted over $30 on a Valarm IoT OTG Y cable. It does not work at all as a host cable for any USB device on the G4. I was hoping to use the Valarm cable to connect a USB DAC and charge the phone at the same time. The cable will let me charge the phone but whatever I connected to the USB female port is not recognized. If anyone finds a USB host cable that allows charging, please post!
Click to expand...
Click to collapse
From what i understand otg goes one way or the other it cant act as a host and carge at the same time. It flips the charging circut to flow out instead of in. Ive been through this on a few phones tried even straight wiring a powerline to the otg itll power the usb device but not charge the phone.
TheMadScientist420 said:
From what i understand otg goes one way or the other it cant act as a host and carge at the same time. It flips the charging circut to flow out instead of in. Ive been through this on a few phones tried even straight wiring a powerline to the otg itll power the usb device but not charge the phone.
Click to expand...
Click to collapse
The manufacturer of that cable clearly states that it'll charge a samsung phone, not confirmed working on a G4 though. Here is the link, http://shop.valarm.net/products/micro-usb-host-otg-y-cable-with-micro-usb-power-for-samsung
I wish there was a way to enable charging using OTG.
mattnin said:
The manufacturer of that cable clearly states that it'll charge a samsung phone, not confirmed working on a G4 though. Here is the link, http://shop.valarm.net/products/micro-usb-host-otg-y-cable-with-micro-usb-power-for-samsung
I wish there was a way to enable charging using OTG.
Click to expand...
Click to collapse
Yea me to i have a few devices that hook to my car that drain my tablet and phone batts and it kills me the only other way ive got it to work is hard wire a charger to the phone. But of coarse this is a old throw away gs3 that im talkin bout not my g4. I havnt tried on my g4 yet but its all phone specs has to have dual charging circuts cause they can only flow one at a time. Now some new devices i know. Do support otg with charging capabilities.

Adapter / splitter (?)

I have a cable which plugs into my charging port which then has a usb slot on the end. I want to watch films on my tablet which I can now do but I also need to be able to charge the tablet at the same time. Is there some kind of double socket I can plug into the charger point that I can then use to plug the charger and my existing usb cable into use both at the same time? What would this be called, I've tried searching splitters and adapters but this only seems to come up with car chargers which is not what I need.
Thanks!

Categories

Resources