Dear all,
i've got 2nd hand xda stealth for 2 weeks, now my stealth cannot boot (black screen, call and End Button are light) after i flash my stealth with wrong ram with nb0 extension on miniSD. please any one can help me to recover my Stealth ?
sorry for my bad english.
xda stealth..
go to www.seeo2.com, download a rom upgrade utility from there.. then start upgrade procedure again. As xda stealth is a hybrid phone..dont try any custom roms on it..
thank's malhar for responding my thread.
i already download the upgrade rom from the o2 site (now is www.mwg.com), i put the rom to my SDCard, the problem is how can i enter the boot loader, in case my stealth always in blank screen with call and end button are light.
i already press press power + call + end button, but my stealth stuck on that condition. every method of flashing mode i already try but no response from my stealth.
Syaipul
oh yea malhar, for information i read the procedure for upgrading on o2 site that connect status is required for upgrading procedure in activecync, my stealth has disconnected status when i plug to my com. can i do the upgrade the rom in this case?
buddy, remove ur sd card from the device first..and then hard reset ur device by pressing reset button via stylus, then flag which is windows home key and then ok key..reset+flag+ok.. maintain the sequence..press reset first keep on pressing then flag and ok key.. it will format ur device.... then try to flash new rom on it
ok malhar, i'll try tomorrow. thanks.....1000x
sad-sad-sad
my stealth cannot boot (black screen, call and End Button are light) after i flash my stealth with wrong ram on miniSD. please any one can help me to recover my Stealth
Your SPL boot loader sounds like it is gone, formatted...
You may be able to patch it, using scripts & mtty if you can get into DL mode. Sounds like you're stuck in OEMSBL though.
help me !!!!
i have try pressing flat and ok botton to format . but nothing appear on the screen . is the other way to format or upgrade rom .
• The device doesn't boot, I see only O2 logo. Hard reset doesn't help and the Firmware update process stops with the first message?
1. turn off the device;
2. enter engineering mode;
3. in Main menu choose Boot Config;
4. in Configuration menu choose EBOOT-Launch Image;
5. turn off the device;
6. now hard reset or upgrade firmware.
Sometimes helps another method: leave the device without the battery for about 30 minutes, then turn your O2 XDA Stealth on.
• How to enter engeneering mode?
1. turn off your O2 XDA Stealth ;
2. hold Flag, OK and Camera + press and hold Power button;
3. use navigation buttons to select the settings.
Click to expand...
Click to collapse
follow this thread from YUC wm6
http://forum.xda-developers.com/showthread.php?t=352468
blank screen
for my case, i cant even see the o2 logo, only blank screen. is there any other way to reboot ?
cant see o2 logo
for my case, i cant even see the o2 logo, only blank screen. is there any other way to reboot ?
randysng said:
for my case, i cant even see the o2 logo, only blank screen. is there any other way to reboot ?
Click to expand...
Click to collapse
Have you tried removing the battery for few hours ??? Does the engineering mode work???
engineering mode
engineering mode ? how to set engineering mode ?
randysng said:
engineering mode ? how to set engineering mode ?
Click to expand...
Click to collapse
How to enter engeneering mode?
1. turn off your O2 XDA Stealth ;
2. hold Flag, OK and Camera + press and hold Power button;
3. use navigation buttons to select the settings
can u see..lights on keypad??what happens when u connect to pc..any sound or error
??
malhaar said:
can u see..lights on keypad??what happens when u connect to pc..any sound or error
??
Click to expand...
Click to collapse
i have a O2 tealth hanged on O2..... i tried hard reset but din work .... i downloaded new rom and software for updation .....but the problem is i cannot connect to pc.... active sync is installed...... plz help
khalifa_smart said:
i have a O2 tealth hanged on O2..... i tried hard reset but din work .... i downloaded new rom and software for updation .....but the problem is i cannot connect to pc.... active sync is installed...... plz help
Click to expand...
Click to collapse
It worked for me
Goto to your PDA setting and uncheck USB to PC.
Note: Check task before connecting to USB ensure no task including Active Sync.
FYI.
Im using VISTA Ultimate to update my XDA.
From WB 6.1 back to WM5. WM 6.1 too buggy and battery drained fast.
Cheers!
Please help me O2 stealth it dead not boot and blank screen .Are you Jtag for it please post it here.
i have the same problem --- my stealth is absolutely dead after using a cheap local charger
i have dismantled the board and taken some pics of the jtag connectors -- made the common LPT port jtag cable
how to proceed from here ?????
is the procedure similar to that of jtag recovery of a flame or an atom exec ??
how do i find the bootloader for O2 Stealth for flashing the NAND memomy Disk on Chip ??
please share your insights
Hello everybody,
I have tried to upgrade my Diamond with a new Radio ROM but it didn't work.
Now I'm blocked to a screen wich says :"
"Upgrade ROM code Error"
Even I have tried to make a har reset, I always obtain this screen.
Is there a way to connect the Diamond to my PC with the usb cable in order to delete the bad file (Radio ROM).
If it's possible, i think, it will boot normally ...
Thanks a lot !
Enter bootloader mode and reflash another Radio.
How can I do to enter in Bootloader Mode ???
danaobrest78 said:
How can I do to enter in Bootloader Mode ???
Click to expand...
Click to collapse
Google as well as the search function of this forum both know.
here you go
hope this helps
http://forum.xda-developers.com/showthread.php?t=405659
Hello,
I have a big problem with my PDA...
I can't update the bios anymore.
When I try with the HP update software (in Pre-BL mode), the program can't find the real details :
(I have a french version)
=> img17.imageshack.us/img17/1297/hpupdate.jpg (sorry, can't post url because I'm new user)
The update stops at 0.1% then, the iPAQ restarts and freezes. I have to remove the battery to reboot to Pre-BL mode.
So, I tried with the universal bootloader (sourceforge.net/projects/ubl/) and when I select the rom file, the program stops at : "Status: Flashing rom to your device.. 0% Complete.".
What can I do?
Thanks for your help
I got news :
I tried to connect to the iPAQ with mtty. I have the USB option (so my iPAQ is recognized by the computer) but there is a problem : I don't have the USB or CMD prompt when I push Enter key... I can't do anything.
The window is white and there is | blanking.
So, I think the only way to repair the rom is to flash with the SD card.
What's the good way to do this ?
Thanks and sorry for my bad english.
sorry for my bad inglish 1st, i have a problem with my ace gt-s8530, i can´t make reset to the phone, my boton up and down don´t work, and i dont now, the phone was given me by a friend and the touch screen is crash, but works, and he forgot the password of dots when you make the sequence, and i can´t put the phone in debug mode usb to make with others programs. any idea how I can do?:good:
Hi guys....
Ihave make the firmware restore with Heimdall,
and after the phonestay blocked in the downloading status, I try to restart and nothing is happennend....
ever in download mode, I have enter in recovery mode, make one complet format....
After I have saw I have put the right file inside, but one bad command.....
So i have remake the firmware restore...
the phone appear good.....but after a while have began to restart, than have some lag, some freezer mode....
I have try to make another hard reset, but still have this problems......
Now I have try to install another firmware ( before i have install the Italiuan firmware the 4.4.2) now the Germany firmware.......
With this last firmware the phone is still blocked, dont appear the configuration system, just write installing application .... than have one rest.... is on loop mode
Somebody can tell me what I have to do???' Because in one Italian site have wrote me I haveto buy one PC...
Mac is no good for this kind of operation...
Excuse me for my horrible English.
Waiting your answers.....
MAx