No sound after battery replacement - HTC One X

Hi
Month ago i replaced battery and since then i have no rear speaker sound. I've tried to fix it by reopening and looking where i didnt connect the cable or something but i cant find the problem. Can anyone tell me where are the cables for speaker because i didnt found nothing on google...

HOX rear speaker
foxxx46 said:
Hi
Month ago i replaced battery and since then i have no rear speaker sound. I've tried to fix it by reopening and looking where i didnt connect the cable or something but i cant find the problem. Can anyone tell me where are the cables for speaker because i didnt found nothing on google...
Click to expand...
Click to collapse
The rear speaker on the HOX sits in the bottom of the rear shell and has two gold coloured spring pins that push up against the mainboard. I have come across the problem when fixing them that the pins get pushed down so they don't contact the board, or can be easily broken off if bent to far. Try bending pins up so the tips sit about 1-1.5mm above the speaker housing. hopefully the picture I've attached shows the pins clearly enough. If this fails to work try replacing the speaker, they are fairly cheap if this doesnt fix the problem you may have a hardware/software fault but try the easy stuff first.

okhughes said:
The rear speaker on the HOX sits in the bottom of the rear shell and has two gold coloured spring pins that push up against the mainboard. I have come across the problem when fixing them that the pins get pushed down so they don't contact the board, or can be easily broken off if bent to far. Try bending pins up so the tips sit about 1-1.5mm above the speaker housing. hopefully the picture I've attached shows the pins clearly enough. If this fails to work try replacing the speaker, they are fairly cheap if this doesnt fix the problem you may have a hardware/software fault but try the easy stuff first.
Click to expand...
Click to collapse
I've bend the pins for 1-2mm and still no sound... i dont know what else to do... i wiped the pads with alcohol and still not working...

foxxx46 said:
I've bend the pins for 1-2mm and still no sound... i dont know what else to do... i wiped the pads with alcohol and still not working...
Click to expand...
Click to collapse
Was thinking about it again and pins do not sit on mainboard but rest on the flex cable that also houses the bottom led's for the home button etc.follow that back and make sure it is connected properly in its connector although it should be if your home button led's are working. Also check there are no small tears accross the flex cable,I have also come across tiny tears across one track before.

It some problema happened with me, but the volume button aren`t working... if someone know something about, help me! i don`t get boot or resset after drain all battery and not boot again!

petterson99 said:
It some problema happened with me, but the volume button aren`t working... if someone know something about, help me! i don`t get boot or resset after drain all battery and not boot again!
Click to expand...
Click to collapse
you didnt put the volume rocker up side down did you? Take the phone apart and check

SÜPERUSER said:
you didnt put the volume rocker up side down did you? Take the phone apart and check
Click to expand...
Click to collapse
I`ll check... tks

Related

UNIVERSAL : need a Coaxial Cable Pre-assy replacement

Hello
I am new on this forum, sorry if this type of question has alreday been answered.
I've got a UNIVERSAL/ SPV M500 and the Coaxial Cable (linking the screen and the keyboard) has been twisted and is damaged.
Where can I find/buy a spare part to replace it ? the reference number is 73H00233-01M (Coaxial Cable Pre-assembly) as indicated in the service manual.
Thank for your help.
Hey,
If you find it let me know, I need one two. Actually these are two cables the Coaxial (Display) and Coaxial (Functional). My screen goes white in landscape mode and I confirmed it's the cable by disassembling my machine. However was unable to find that cable Will let you know if I find it.
Me too.
I am getting odd touch screen errors and think it can only be the cable.
If anyone knows of a supplier, please post here.
Has anyone tried contacting HTC directly?
I've tried HTC europe , they forwarded me to the local repair centre. this one do not sell spare parts without repairing the item.
I'm trying to contact various shops . I'll let you know if it is successful
villard said:
I've tried HTC europe , they forwarded me to the local repair centre. this one do not sell spare parts without repairing the item.
I'm trying to contact various shops . I'll let you know if it is successful
Click to expand...
Click to collapse
Thanks,
Please do let me know, I really need that cable.
MOBILER
Finally ... got cables !
Here mate ... take this adress
http://qinyieproduct.diytrade.com/sdp/444314/4/pd-2468984/2411741-0.html
villard said:
Hello
I am new on this forum, sorry if this type of question has alreday been answered.
I've got a UNIVERSAL/ SPV M500 and the Coaxial Cable (linking the screen and the keyboard) has been twisted and is damaged.
Where can I find/buy a spare part to replace it ? the reference number is 73H00233-01M (Coaxial Cable Pre-assembly) as indicated in the service manual.
Thank for your help.
Click to expand...
Click to collapse
found coaxial cable for £60 plus vat.
villard said:
I've tried HTC europe , they forwarded me to the local repair centre. this one do not sell spare parts without repairing the item.
I'm trying to contact various shops . I'll let you know if it is successful
Click to expand...
Click to collapse
Give this site a look, http://www.apexlaptops.co.uk/Universal.htm
I have been having the same problems as you guys. my uni have been getting "white screen of death" for about 6 months now.
I am going to take out the cable and try and fix it myself. (fingers crossed)
I will let you all know how it goes. I felt £60 plus vat and postage was a bit steep.
coax cable
Fixed it!!
I took apart my uni down to the last screw, and rebuilt it.
In the process I did find that i am missing an antenna in the back, it should have 3 but only has 2. oh well it works.
The 3rd antenna is for 3g and i am not on 3.
Anyway back to my uni.
The coax conectors where a little lose, so after a good clean in a solven cleaner and popped back in to the conector holder, after playing for 20 mins I found that they poped back out verry slightly, just enough to make the screen go white and not function.
So the solution is to make sure it does'nt come back out.
ok.
well I have as a tempery solution put a tiny bit of foam on top of the connecter and held it in place with a bit of tape.
If this works for longer than a month then i will solder the cable down.
Touch wood it seems to be working. I will try and get some photos done tonight
gingerchristopher.
Hi,
Congratulations!
What tools did you use for this job(srews, tweezers)?
gingerchristopher said:
Fixed it!!
I took apart my uni down to the last screw, and rebuilt it.
In the process I did find that i am missing an antenna in the back, it should have 3 but only has 2. oh well it works.
The 3rd antenna is for 3g and i am not on 3.
Anyway back to my uni.
The coax conectors where a little lose, so after a good clean in a solven cleaner and popped back in to the conector holder, after playing for 20 mins I found that they poped back out verry slightly, just enough to make the screen go white and not function.
So the solution is to make sure it does'nt come back out.
ok.
well I have as a tempery solution put a tiny bit of foam on top of the connecter and held it in place with a bit of tape.
If this works for longer than a month then i will solder the cable down.
Touch wood it seems to be working. I will try and get some photos done tonight
gingerchristopher.
Click to expand...
Click to collapse
re: fixed it
Yes just a torex screwdriver size 6 to take out the 4 security screws in the battery tray, watch makers screwdrivers and a pair of fine point tweezers.
still having problems with my camera so photos will follow when i take it apart to solder.
ang how about antistatic gloves?
gingerchristopher said:
Yes just a torex screwdriver size 6 to take out the 4 security screws in the battery tray, watch makers screwdrivers and a pair of fine point tweezers.
still having problems with my camera so photos will follow when i take it apart to solder.
Click to expand...
Click to collapse
Anti Static gloves!!
Because of the Job I do, I have an earthing band to connect the phone and me to the wall, and put the phone on an anti static table cover. All is good so far. I am looking at Feb to solder (as i have some leave in). There will be detailed photos and description.
Untill then........
Just found a coax on e-bay
Hi I hope anyone who is after this coax cable can read this before the weekend is out, as there is one on e-bay for £40 this is the link.
http://cgi.ebay.co.uk/NEW-O2-XDA-EX...9QQihZ020QQcategoryZ41343QQrdZ1QQcmdZViewItem
Chris.
Good done man go ahaed, and plz try to post the photos.
Another question, my universal some times lost its external speaker sound, so i cannot hear the rings, when i press on the back of the device, exactly on the battery cover in the middle between the two dummy holes and the usb port, it works again. Do u think that this is due to the coaxial damage also, even i don'y have any problem in the screen??
hbahaie said:
Good done man go ahaed, and plz try to post the photos.
Another question, my universal some times lost its external speaker sound, so i cannot hear the rings, when i press on the back of the device, exactly on the battery cover in the middle between the two dummy holes and the usb port, it works again. Do u think that this is due to the coaxial damage also, even i don'y have any problem in the screen??
Click to expand...
Click to collapse
nope. open up and check the contacts
omega_ said:
nope. open up and check the contacts
Click to expand...
Click to collapse
Thank you very much for your advice, I'll check. Thanks
hbahaie said:
Thank you very much for your advice, I'll check. Thanks
Click to expand...
Click to collapse
I have disassembled my uni and checked for all connections, but there was no improvement. I can confirm that the disappearance of external speakers sound is not due to co-axial cable. The proof is that i extracted my main borad from my uni and implanted it in another one, i assumed that the problem will be rsolved, but the same problem still exists. Ok, now i can disassemble my uni for smallest piece, but any one advise me where is th connection part or the piece that causes that problem. Again a brief description of the problem:
when there is a coming call, i cannot here the ring or it is sevrely intermitent, also when i play any WMP file, i cannot here the sound, if I press firmly on the base or around the keyboard the sound comes again and may last for a few minutes or disappear after another press. So, there is a lose part in the main board i think that needs fixation, but which one????
Hi all
Now it takes me more than a month to upgrade my JASJAR due to a lot of problems I faced during this upgrading adventure… anyway, the last problem I still have is that after upgrading the screen goes crazy, I mean if you press on the screen the colours are mixed for few seconds and then its ok but at any time I touch the screen again the same happened so you can imagine what if I am going to dial a number or write a message …. So can anyone advice me what to do? …
The rom version is 1.13.82
Radio 1.04.02
Extrom 1.13.188
And I think the bootloader 1.00 and I don’t know why I feel that the bootloader is the reason ... I made a deep search but I couldn’t find problem like mine
gingerchristopher said:
The coax conectors where a little lose, so after a good clean in a solven cleaner and popped back in to the conector holder, after playing for 20 mins I found that they poped back out verry slightly, just enough to make the screen go white and not function.
So the solution is to make sure it does'nt come back out.
ok.
well I have as a tempery solution put a tiny bit of foam on top of the connecter and held it in place with a bit of tape.
Click to expand...
Click to collapse
Sitting next to my M5000 and all of a sudden the screen turned on but was white!
Following your lead I found that the first i.e. 'underneath' connector was not fully home. A little push and all is well.
Took the time to pack out the housing for the stylus to stop the little blighter escaping whilst in there.
Thank you for taking the time to post gingerchristopher.
Pete

Disassemble and reassemble of galaxy nexus :)

I have a few pictures of my galaxy nexus broken down if anyone would like to ask me questions on how and where things go they can. I actually find this phone to be very easy to get apart and if careful can be reassembled in 15 minutes. I was actually replacing my speaker with some old parts I bought off a guy. No more crackling! Anyways in the process grabbed some pics
U can see the first three are the screen bottom speaker, main board, vibe, etc. The last pic she's all back together
Sent from my Galaxy Nexus using xda premium
Somehow I imagined a picture of me tearing down a smartphone where I was photoshopped out and replaced with a picture of a dog in a labcoat saying: "I have no idea what I'm doing"
Yep this phone is one of the easiest ive worked with. had to open mine to replace the earpiece. the only thing to take care of is the volume ribbon and vibrator wires, they can snap off really easily.
IINexusII said:
Yep this phone is one of the easiest ive worked with. had to open mine to replace the earpiece. the only thing to take care of is the volume ribbon and vibrator wires, they can snap off really easily.
Click to expand...
Click to collapse
is the imei sticker that is attached onto the black plastic removable from the main board?
IINexusII said:
Yep this phone is one of the easiest ive worked with. had to open mine to replace the earpiece. the only thing to take care of is the volume ribbon and vibrator wires, they can snap off really easily.
Click to expand...
Click to collapse
Yes sir....I just stuck a razor blade between them and the housing and they come right off connected to a gel like glue. This was good because sticking them back in place they actually stayed. U also have to remove the vibrator motor and the long black wire running down alongside the battery compartment (it has connectors on each end) then of course your two ribbon connectors for main board then one ribbon connector for bottom speaker. Didn't touch cams no need to.....very very easy job in fact it was to easy.
I have to replace my USB board (my USB port was damaged) and I am a newbie doing this kind of service myself. I bought it on ebay:
http://www.ebay.com/itm/OEM-Charger...ltDomain_0&hash=item35bc2f9280#ht_3392wt_1052
Do you think it is possible for someone with no experience to make it? I think I will try it myself, not in the mood to send it to some repair shop and wait 30 days..
juliano_q said:
I have to replace my USB board (my USB port was damaged) and I am a newbie doing this kind of service myself. I bought it on ebay:
http://www.ebay.com/itm/OEM-Charger...ltDomain_0&hash=item35bc2f9280#ht_3392wt_1052
Do you think it is possible for someone with no experience to make it? I think I will try it myself, not in the mood to send it to some repair shop and wait 30 days..
Click to expand...
Click to collapse
Yes for sure...but if u do not feel safe doing it then take it in. I know to get to the usb the whole speaker and housing comes off of the top of that. Which is one screw then a ribbon fairly easy....then u just work something thin in between that and housing like a guitar pic or Mac card. I would go with guitar pic tho so u don't mess the corners of your card up. I know that once the speaker portion is off u see in my first pic the USB I think has its on board. I truthfully did not take that portion of it out thought it was kind of pointless. If u need help I will assist u if u decide to do it yourself
sarni84 said:
Yes for sure...but if u do not feel safe doing it then take it in. I know to get to the usb the whole speaker and housing comes off of the top of that. Which is one screw then a ribbon fairly easy....then u just work something thin in between that and housing like a guitar pic or Mac card. I would go with guitar pic tho so u don't mess the corners of your card up. I know that once the speaker portion is off u see in my first pic the USB I think has its on board. I truthfully did not take that portion of it out thought it was kind of pointless. If u need help I will assist u if u decide to do it yourself
Click to expand...
Click to collapse
Thanks, I think I will try it myself, just have to wait for it to arrive.
juliano_q said:
Thanks, I think I will try it myself, just have to wait for it to arrive.
Click to expand...
Click to collapse
Yea dude pm me and I'll definitely help out
Thats pretty neat man, do you know where the GPS chip is?
I replaced my back cover and apparently I damaged the GPS chip cause I have NO gps lock, software side its ruled out (I flashed many diff ROMS, kernels and Radios and it used to work well before I opened up my Gnex)
Thank you.
where is the VZ LTE radio? maybe i can swap mine out for one that doesnt cause signal drops.
Sergio PC said:
Thats pretty neat man, do you know where the GPS chip is?
I replaced my back cover and apparently I damaged the GPS chip cause I have NO gps lock, software side its ruled out (I flashed many diff ROMS, kernels and Radios and it used to work well before I opened up my Gnex)
Thank you.
Click to expand...
Click to collapse
The battery cover? Hmmmm. I am pretty sure the GPS chip is on the opposite side of motherboard. Looking at ifixit photos it says right by rear camera on the opposite side of motherboard.
Edit...also if u look at first pic in my pictures look on right side of battery compartment . See the black wire with the connectors on each end? I wonder if the connector closest to bottom came loose or has something to do with it
10roller said:
where is the VZ LTE radio? maybe i can swap mine out for one that doesnt cause signal drops.
Click to expand...
Click to collapse
Not sure I have GSM model. And dude good luck with that unless u know how to solder chips on to motherboards that is nearly impossible and I think swapping a lte chip for another lte chip won't solve your problem
sarni84 said:
The battery cover? Hmmmm. I am pretty sure the GPS chip is on the opposite side of motherboard. Looking at ifixit photos it says right by rear camera on the opposite side of motherboard.
Edit...also if u look at first pic in my pictures look on right side of battery compartment . See the black wire with the connectors on each end? I wonder if the connector closest to bottom came loose or has something to do with it
Click to expand...
Click to collapse
Thanks, appreciate your time.
I checked out ifixit, thinking that in the process of removing the cover I could of hit the GPS chip or something, but since you pointed out that its on the opposite side of the motherboard that's not a possibility. Since I have not removed the mother board.
I have not opened it again, afraid of ruining something else.
But I guess I will have to in order to check the wire you speak about.
Salutations
I sent my phone in for repair to Samsung via Expansys for a bad external speaker. Back when it went bad, phone was too new to have all parts available as spares on the net plus the phone was still under warranty so I send it back to Samsung via Expansys-usa. But what I think happened is that Expansys didn't send it to Samsung and repaired it inhouse. I can say that because all screws inside the phone had chewed up heads and the repair didn't look good however the external speaker was working. First thing I found out that external volume rocker was not working anymore. So I send it back again to Expansys and I just received it back today with a note saying that the volume rocker ribbon pins have come away from the main board and taken the pin with them.
Bottom line is that they didn't repair the phone. Any ideas on how I can get this fixed? Do I have to change the ribbon? if I want to do it myself or this sort of damage requires a new board?
Any ideas comments are appreciated.
Edit: Link to photo showing the pins that are separated from the board
sarni84 said:
I have a few pictures of my galaxy nexus broken down if anyone would like to ask me questions on how and where things go they can. I actually find this phone to be very easy to get apart and if careful can be reassembled in 15 minutes. I was actually replacing my speaker with some old parts I bought off a guy. No more crackling! Anyways in the process grabbed some pics
U can see the first three are the screen bottom speaker, main board, vibe, etc. The last pic she's all back together
Sent from my Galaxy Nexus using xda premium
Click to expand...
Click to collapse
Hi Sarni,
I accidentally snapped the ribbon (refer to attached pic, circled in red), and now my speaker is not working anymore. I guess that ribbon was for connecting the speaker and headphone jack? . What do you think i should do now, replace the whole piece?
I also intend to replace my damaged charge port, but not sure how to proceed for that.
Thanks,
Dennis

[Q] No Wifi After LCD Replacement

Hi guys,
I recently dropped my phone on concrete, resulting in a nasty crack across the screen. Last night I received the new LCD/Digitizer and went ahead and replaced the screen (I opted to replace the LCD as well due to the copious amounts of glue used between the two parts). After many curse words were shared, I put it back together again and everything works perfectly... except Wifi.
I was wondering if anyone has had a similar issue, and where I should start looking to fix this? I took the cover off again to check both white (wifi?) cable and black (bluetooth?) cables, and both were connected as they should be.
Any help would be very much appreciated!
Tim
Go back through and check every wire and hook up. That's all you can do.
- hit my thanks button if i helped you -
hukel56 said:
Go back through and check every wire and hook up. That's all you can do.
- hit my thanks button if i helped you -
Click to expand...
Click to collapse
Yeah, thanks for the reply. I went through it on Saturday very carefully looking for any wire or contact that was loose and unfortunately everything was correctly attached. I did notice that the bluetooth and wifi wire plugs on the lower board were *very* close to each other, so they may well have touched and caused a short. After checking everything over and reassembling the phone, wifi still didn't work I also checked bluetooth and that won't work either, so perhaps my suspicions about the wires contacting is correct.
Note to anyone else doing a repair on this phone: Be very careful that the wifi and bluetooth plugs don't touch each other. It's very easy for them to rotate around in their socket and contact each other. I'm not sure if this caused them to fail in my phone, but it could certainly be the reason why both no longer work.
Cheers
Did you seperate the wires...and did that work.
hukel56 said:
Did you seperate the wires...and did that work.
Click to expand...
Click to collapse
Yep, I separated the wires and still no luck :/
I also removed the wires just to see if it would at least turn allow me to turn on the wifi, but all it says is "error" in the wifi settings and I can't turn wifi on no matter what I try.
I have exact same problem: after LCD replacement wifi fails with ERROR. Also sometimes no reaction to POWER button - no power off menu neither LCD is off/on. Don`t expect any wires or so i could accidentally damage.
Solved
After dissasembling phone again i found that flex cable has not good connection to mainboard. I pressed connectors, felt some "click", reassembled phone and after booting everything is ok:
wifi, bt, volume buttons, leds while charging operating well. Attaching picture. The connectors are located right under sim card and micro sd card slots, you have to remove full mainboard and flex cable to fix that. Cheers!
juzis28 said:
After dissasembling phone again i found that flex cable has not good connection to mainboard. I pressed connectors, felt some "click", reassembled phone and after booting everything is ok:
wifi, bt, volume buttons, leds while charging operating well. Attaching picture. The connectors are located right under sim card and micro sd card slots, you have to remove full mainboard and flex cable to fix that. Cheers!
Click to expand...
Click to collapse
That's really interesting. Thanks for the info. It's odd that the phone even functions if the flex cable might be loose. I may have a look and see if this is the problem too when I get a chance.
Yes, phone operate, but really weird behavior - some functions worked, some not, sometimes no reaction to power on button and so on. Hope this helps someone.
juzis28 said:
Yes, phone operate, but really weird behavior - some functions worked, some not, sometimes no reaction to power on button and so on. Hope this helps someone.
Click to expand...
Click to collapse
Hmm. I wonder if my issue is the same. I have experienced absolutely no odd behaviour other than wifi + bluetooth not working. Everything else works as it used to. GPS actually seems to work better haha. There are two flex cables so perhaps one of them does those two things.
TimHawker said:
Hmm. I wonder if my issue is the same. I have experienced absolutely no odd behaviour other than wifi + bluetooth not working. Everything else works as it used to. GPS actually seems to work better haha. There are two flex cables so perhaps one of them does those two things.
Click to expand...
Click to collapse
If you haven`t found any other damage: wires, pcb, then most probably your issue is related to exact flex cable. Yes, here are two contacts where flex cable connects to m/b, its clearly seen on photos i attached. My problem was both flex cables become loose...
You're a real man. I would have paid someone to fix my screen.
DIY makes you a real man? lol
- sent from a flux in space -
juzis28 said:
After dissasembling phone again i found that flex cable has not good connection to mainboard. I pressed connectors, felt some "click", reassembled phone and after booting everything is ok:
wifi, bt, volume buttons, leds while charging operating well. Attaching picture. The connectors are located right under sim card and micro sd card slots, you have to remove full mainboard and flex cable to fix that. Cheers!
Click to expand...
Click to collapse
My WiFi (and Volume Keys) stopped working after I dropped my phone.
After reading your solution I removed the SIM/SD-Cover and just by pressing from outside, the cable snapped in.
No disassembling, not even a reboot! My DHD works like on it's first day!
Thanks!

Replacing the charging port

Hey all,
I just replaced the charging port on my m8 and wanted to let people know it is straight forward. My port got corroded and was shorting out, melting the adapter and not charging the phone. I sent it in hoping for warranty, but the replacement quote was $400! (due to S-off they "had" to replace the entire motherboard). The phone has a separate pcb with the micro usb charge port and headphone input.
example:
http://www.witrigs.com/media/catalo...a71cb48e3d52cb890e76f9e6353/1/0/109063-01.jpg
To remove this board you need to do a few easy things:
1) disconnect the ribbon and remove the insulating tape (to reattach to new part)
2) unsnap the small white power cable
3) loosen the screw on the motherboard near the headphone input. This is clamping down the assembly a bit
tools required:
phillips 00
t5 torx bit
spudger/guitar picks
I would recommend prying the phone out of the frame starting from the bottom. I started from the top and bent the thin strip of aluminum above the sim slot when prying it out.
Also, you can pry the bracket/spring off the top of the old usb port to give the new one a tight fit if your replacement didnt come with it (like mine)
Lastly, just note that power button fell out as soon as I pried the frame apart from the guts. This made it a bit of a pain to reassemble - just be sure to reassemble with the top in first. That will keep the power button in place.
The replacement part cost me $30, so it was definitely worth it! phone now works great.
bookfast said:
Hey all,
I just replaced the charging port on my m8 and wanted to let people know it is straight forward. My port got corroded and was shorting out, melting the adapter and not charging the phone. I sent it in hoping for warranty, but the replacement quote was $400! (due to S-off they "had" to replace the entire motherboard). The phone has a separate pcb with the micro usb charge port and headphone input.
example:
http://www.witrigs.com/media/catalo...a71cb48e3d52cb890e76f9e6353/1/0/109063-01.jpg
To remove this board you need to do a few easy things:
1) disconnect the ribbon and remove the insulating tape (to reattach to new part)
2) unsnap the small white power cable
3) loosen the screw on the motherboard near the headphone input. This is clamping down the assembly a bit
tools required:
phillips 00
t5 torx bit
spudger/guitar picks
I would recommend prying the phone out of the frame starting from the bottom. I started from the top and bent the thin strip of aluminum above the sim slot when prying it out.
Also, you can pry the bracket/spring off the top of the old usb port to give the new one a tight fit if your replacement didnt come with it (like mine)
Lastly, just note that power button fell out as soon as I pried the frame apart from the guts. This made it a bit of a pain to reassemble - just be sure to reassemble with the top in first. That will keep the power button in place.
The replacement part cost me $30, so it was definitely worth it! phone now works great.
Click to expand...
Click to collapse
Hey there. Interesting to know that you replaced it all your self . Did you put everything back perfectly ? I mean the display being aligned properly to the body, the speaker grills being flushed with the body; ? Weird to ask, but did you damage anything while doing it all yourself ? Like the screen scratches, or something else ? Sorry, for asking these... Thanks in advance :good:
Tej XFire said:
Hey there. Interesting to know that you replaced it all your self . Did you put everything back perfectly ? I mean the display being aligned properly to the body, the speaker grills being flushed with the body; ? Weird to ask, but did you damage anything while doing it all yourself ? Like the screen scratches, or something else ? Sorry, for asking these... Thanks in advance :good:
Click to expand...
Click to collapse
I haven't re-glued the speaker covers back on yet so I dont know if they will be perfectly flush or not, although they still look flat so I think it will look good.
The only damage is a slight bend in the frame on the screen side of the sim tray slot. The metal is thin, and I pried against it to get the hardware out of the frame. That is why I recommended to start from the bottom when separating the two. Doing this should allow others to avoid this problem. It is slight, maybe 1/4mm gap where it used to be flush along the side of the screen above the sim tray.
Otherwise everything was smooth. The screen/frame etc are still mint.
bookfast said:
I haven't re-glued the speaker covers back on yet so I dont know if they will be perfectly flush or not, although they still look flat so I think it will look good.
The only damage is a slight bend in the frame on the screen side of the sim tray slot. The metal is thin, and I pried against it to get the hardware out of the frame. That is why I recommended to start from the bottom when separating the two. Doing this should allow others to avoid this problem. It is slight, maybe 1/4mm gap where it used to be flush along the side of the screen above the sim tray.
Otherwise everything was smooth. The screen/frame etc are still mint.
Click to expand...
Click to collapse
Cool, you've done it like a pro then. :good: .Any picture describing the damage would be helpful, if you can provide. Is the display mint ? No scuffs/scratches on it ? But, my speaker grills were damaged onto the edges after the repair was carried out. Does yours show the same sign ? I don't mean the flatness of the grills, but the damage that should be done, while prying out the grills. A picture showing your damage would be helpful to me. I could do the same, if you insist. Thanks ! :good:
Mine is busted. But I cannot find the PCB. The link in the op is dead.
Any ideas?
http://www.witrigs.com/oem-charging-port-flex-for-htc-one-m8
bookfast said:
http://www.witrigs.com/oem-charging-port-flex-for-htc-one-m8
Click to expand...
Click to collapse
I actually got one off eBay for $17.21. Works perfectly.
Just wondering....
Sounds like you were able to avoid some steps in the teardown guide, if I recall it was damn near a total disassemble. Do you have a lot of experience with phones? I want to fix mine, but don't need a tedious project right now. If I repair mine I'd like to put a mini USB in place of the micro if possible, I've seen too many damaged micro usb to trust or like them. As for the speaker grills, if you're picky buy replacements, they're cheap.
microphone on charging port?
bookfast said:
Hey all,
I just replaced the charging port on my m8 and wanted to let people know it is straight forward. My port got corroded and was shorting out, melting the adapter and not charging the phone. I sent it in hoping for warranty, but the replacement quote was $400! (due to S-off they "had" to replace the entire motherboard). The phone has a separate pcb with the micro usb charge port and headphone input.
example:
link
To remove this board you need to do a few easy things:
1) disconnect the ribbon and remove the insulating tape (to reattach to new part)
2) unsnap the small white power cable
3) loosen the screw on the motherboard near the headphone input. This is clamping down the assembly a bit
tools required:
phillips 00
t5 torx bit
spudger/guitar picks
I would recommend prying the phone out of the frame starting from the bottom. I started from the top and bent the thin strip of aluminum above the sim slot when prying it out.
Also, you can pry the bracket/spring off the top of the old usb port to give the new one a tight fit if your replacement didnt come with it (like mine)
Lastly, just note that power button fell out as soon as I pried the frame apart from the guts. This made it a bit of a pain to reassemble - just be sure to reassemble with the top in first. That will keep the power button in place.
The replacement part cost me $30, so it was definitely worth it! phone now works great.
Click to expand...
Click to collapse
My HTC M8's main call microphone has stopped working, and through searches on Google it seems that perhaps that this mic (first mic, non-speakerphone mic) is built into the charging port. Is this the case? I cannot find anything that explicitly says this, and I'd love to get the phone back in working condition.
dm8233 said:
My HTC M8's main call microphone has stopped working, and through searches on Google it seems that perhaps that this mic (first mic, non-speakerphone mic) is built into the charging port. Is this the case? I cannot find anything that explicitly says this, and I'd love to get the phone back in working condition.
Click to expand...
Click to collapse
I too am also curious if the mic is on the usb part because my mic doesnt wrk when i make calls.
Will replacing the usb port fix the problem?
Harvey02 said:
I too am also curious if the mic is on the usb part because my mic doesnt wrk when i make calls.
Will replacing the usb port fix the problem?
Click to expand...
Click to collapse
I called HTC, the mic is on the USB port, although you should make sure that it's not a software issue first. There are several threads on the internet easily found through Google which discuss doing a factory reset to resolve this if it turns out to be a software problem.
Thanks for your reply. I did a factory reset when I got the phone but it still doesn't work. Does that mean it's not a software problem and that if I replace the usb it should work?
Harvey02 said:
Thanks for your reply. I did a factory reset when I got the phone but it still doesn't work. Does that mean it's not a software problem and that if I replace the usb it should work?
Click to expand...
Click to collapse
I would think so, yes.
Thanks! Do you know of any online source confirming that?
Harvey02 said:
Thanks! Do you know of any online source confirming that?
Click to expand...
Click to collapse
No, but from what I've studied about it, it should work. Feel free to contact HTC, they actually have a live chat available somewhere on their website. Good luck to you.
Very interesting, I contacted htc and we went through diagnostics together and the rep said that I have to send it in. I asked him if the mic was on the usb assembly and he said that it wasn't and rather it was on the motherboard, and I clarified that we were talking about the primary mic which is located near the usb port. Confusing bec everywhere I saw online said that the mic is on the usb assembly. Go figure!
Harvey02 said:
Very interesting, I contacted htc and we went through diagnostics together and the rep said that I have to send it in. I asked him if the mic was on the usb assembly and he said that it wasn't and rather it was on the motherboard, and I clarified that we were talking about the primary mic which is located near the usb port. Confusing bec everywhere I saw online said that the mic is on the usb assembly. Go figure!
Click to expand...
Click to collapse
What did you end up doing? Did you discover if it was on the motherboard or the part with the USB port? I've waited a while to repair mine for other reasons, and I am now prepared to fix it. Any information would be helpful.
Just a few notes on my own experience.
I replaced the screen in my friend's M8 a few months ago. Seemed like everything went ok, except after I got done, the mic didn't work anymore. This is strange because it worked fine before, and all I did was remove/replace the circuit board in the process (yes, the small one at the bottom with the uUSB port). However, the upper rear microphone was still working I believe, because people on the other end of the line could still hear if the phone was put into speakerphone mode. I don't know why it would stop working all of a sudden.... Ran the HTC audio test using *#*#3424*#* to confirm main mic wasn't working and that the aux rear mic was.
Fast forward to this week, with my own M8. The uUSB connector was going bad, and I was having trouble charging, so I figured it was time to replace that circuit board. Ordered a new one and replaced, but when I got it back together, the USB port was fine of course, but my mic wasn't working now, just like my friends! On top of that, the headphone jack didn't work at all. Most likely the "cable inserted" signal wasn't getting back up to the motherboard, but didn't check. So pissed off. Also, the new board I got didn't have the bottom left RF connector/circuitry populated. Thinking from research that it might be for the GPS? I should have tested when the board was in there, but didn't. Fixed a bad solder joint on the original board's uUSB connector, which helped, but still charging is a bit messed up. I'd rather have a working mic and headphone jack and have to play with the cable to get to charge for a while until I get another board (from another supplier, jerks).
Yes, the mic is the small chip on the very left side of the board. It has a hole underneath the chip, going through the board and to the front face to receive the acoustics.
I don't know why the mic not working is so common after an HTC One M8 tear down, as it seems many others are having the same issue. One theory I have is that pulling the circuit board from the motherboard while power is still applied (not unplugging the battery first) might be jacking the microphone somehow. Just a theory, but I'd recommend to be safe that anyone replacing the board should unplug the battery cable before replacing the USB/mic circuit board.
I'd just like to chime in to say that I've read about some people having problems with the mic not working after replacing the USB board. From what I understand, there are two different versions of it, and replacing it with the wrong one can cause that very issue. You should look into it.
EDIT: Source - http://www.witrigs.com/blog/htc-one-m8-audio-jack-not-work-after-charging-board-replacement/
Mic broken after USB repair
Old thread but I have the same problem. Replaced USB board and now my mic does not work. However I am pretty certain I did order the correct board (had 2x connectors for my Verizon HTC m8). And my microphone jack work great which others indicate is often broken along with the mic. Anyone have any workarounds?

[Q] HTC ONE X speakers not working

After my attempt to fix WIFI my back speakers became very silent. Today I replaced battery, speakers aren't working anymore at all :crying:
Can someone tell me what should I do? I noticed that one of those thin copper "legs" which are supposed to touch copper plating on casing near speakers was bent, so fixed it, but it didn't help
replace the speaker it cost less than £3, I damaged mine when replacing my battery and rear housing and had to replace it, it's really easy.
Just search "HTC one x speaker" on eBay and you'll have no problem finding one.
guys i replaced screen and battery now loud speaker is dead .. i ordered new one and still not working ..
XDADEVX said:
guys i replaced screen and battery now loud speaker is dead .. i ordered new one and still not working ..
Click to expand...
Click to collapse
After i had taken mine apart, my speaker wasnt working either. I tried connecting the speaker pins to the board manually using wires.. The speaker was then working.
I then realized that this must have been because the pins of the speaker was not connecting to the board.. What i did was removing the black tape which is just around the speaker it self and then making the pins "higher" if you get what i mean.. After this i got it working again.
Let me hear if you get some news
Da9L said:
After i had taken mine apart, my speaker wasnt working either. I tried connecting the speaker pins to the board manually using wires.. The speaker was then working.
I then realized that this must have been because the pins of the speaker was not connecting to the board.. What i did was removing the black tape which is just around the speaker it self and then making the pins "higher" if you get what i mean.. After this i got it working again.
Let me hear if you get some news
Click to expand...
Click to collapse
how did you lift pins they are on flex cable .. i manually put speaker pins onto flex cable pins but didnt work ..and when i put one pin from speaker on flex pin and other completelly somewhwere else not to pin it kind of worked .. so weird
Have a look at my attached image.. It shows two speaker brackets..
As you can see on the bracket lowest in the picture, i have removed the black tape.. Also those two pins i have marked are the ones i suggest you to lift.
The flex cable you are talking about is that the one which is attached to the lcd bracket?
EDIT: Forgot to include the image!
Da9L said:
Have a look at my attached image.. It shows two speaker brackets..
As you can see on the bracket lowest in the picture, i have removed the black tape.. Also those two pins i have marked are the ones i suggest you to lift.
The flex cable you are talking about is that the one which is attached to the lcd bracket?
EDIT: Forgot to include the image!
Click to expand...
Click to collapse
now i can see
Sorry about that please refresh i edited to post to include picture
Da9L said:
Sorry about that please refresh i edited to post to include picture
Click to expand...
Click to collapse
yeah but i removed speaker from that back cover and i placed it onto contacts on the phone where are those two gold contacts on led flex cable but it wont freaking work .. i have ordered new speaker and still so tried to reach seller who sent me flex cable connects to MB but still hasnt received it ..
Hmm sounds wierd.. Can you attach a picture of what you have done?
Da9L said:
Hmm sounds wierd.. Can you attach a picture of what you have done?
Click to expand...
Click to collapse
here check it
Hmm if the speaker is not giving any sounds with that i can only think of the flex ribbon not being connected to the mainboard up on the top right of the battery.
Da9L said:
Hmm if the speaker is not giving any sounds with that i can only think of the flex ribbon not being connected to the mainboard up on the top right of the battery.
Click to expand...
Click to collapse
of course it is even that flex cable is new.. leds lits up
and speaker starts working when speaker is in this position (the pins are against battery and one leg of speaker touches that top contact and right leg touches that light grey area of the flex cable then speaker working i can hear sound but not loud as it should be maybe half loud even when on max vol.

Categories

Resources