[Q] Soft brick - can't push ROM to phone - Verizon HTC One (M7)

Hello,
I am trying to fix my issue and have done a ton of reading but can't figure out where to go from here. I've had my phone rooted for months and tried to flash a newer custom ROM today and it ended up locking my phone into a boot loop. I was able to get out of it and had to re install a recovery tool (have installed both CWM and TWRP and they work fine). But I can't actually get a ROM back onto my phone because I don't have one on the SD card and I can't get one to it. I just want to put a stock ROM back onto it at this point.
I can't boot into windows to access the SD card because whenever I boot the phone normally it just goes back to boot looping. I have tried ADB push when in recovery to put a ROM on the SD card and I continually get permission denied when I try to do that. I have tried ADB sideloader and I can't get that to work either. How can I go about getting a ROM to my phone so I can flash it via CWM/TWRP?
Fastboot works fine and I can flash recoveries no problem. ADB appear to work but I can't understand why I can't just get push to work. Any help would be greatly appreciated.
HTC One M7 on Verizon.
(bootloader) version: 0.5
(bootloader) version-bootloader: 1.54.0000
(bootloader) version-baseband: 1.12.42.0731
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main: 1.10.605.8
(bootloader) version-misc: PVT SHIP S-OFF
(bootloader) serialno:xxx
(bootloader) imei: xxx
(bootloader) meid: xxx
(bootloader) product: m7_wlv
(bootloader) platform: HBOOT-8064
(bootloader) modelid: PN0731000
(bootloader) cidnum: VZW__001
(bootloader) battery-status: good
(bootloader) battery-voltage: 4325mV
(bootloader) partition-layout: Generic
(bootloader) security: off
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: dirty-97af273845
(bootloader) hbootpreupdate: 11
(bootloader) gencheckpt: 0
all: Done!
finished. total time: 0.070s

If you type "adb devices" from a Command Prompt, do you see your phone listed?
Try powering off your phone, then holding Power+VolDown until you get to HBOOT. From there, enter recovery (TWRP is my preferred). ADB push does not require anything to be done prior to using it, so assuming you can see your phone with "adb devices", proceed like this:
Rename the ROM you want to flash to ROM.zip
Type "adb push ROM.zip /sdcard/" No quotes
If the ROM is around 1GB, this will take 5-10 minutes.
Once done, use TWRP file manager (under Advanced) to verify the file is there.
Reboot back into recovery and verify it's still there. If it is, install it. If it's not, you will have to RUU back to stock and go through the unlock process again.

NotATreoFan said:
If you type "adb devices" from a Command Prompt, do you see your phone listed?
Try powering off your phone, then holding Power+VolDown until you get to HBOOT. From there, enter recovery (TWRP is my preferred). ADB push does not require anything to be done prior to using it, so assuming you can see your phone with "adb devices", proceed like this:
Rename the ROM you want to flash to ROM.zip
Type "adb push ROM.zip /sdcard/" No quotes
If the ROM is around 1GB, this will take 5-10 minutes.
Once done, use TWRP file manager (under Advanced) to verify the file is there.
Reboot back into recovery and verify it's still there. If it is, install it. If it's not, you will have to RUU back to stock and go through the unlock process again.
Click to expand...
Click to collapse
No it isn't showing up when I do that while in recovery.
C:\Users\Mat\Desktop\adb>adb devices
List of devices attached

factor00 said:
No it isn't showing up when I do that while in recovery.
C:\Users\Mat\Desktop\adb>adb devices
List of devices attached
Click to expand...
Click to collapse
What about fastboot?

NotATreoFan said:
What about fastboot?
Click to expand...
Click to collapse
Yes fastboot is working. I can see the phone info still. You said I can just RUU. I didn't realize I could do that. That's fine with me I have no issue with that.
I just re-lock the boot loader and then run the RUU from windows? Would this be the appropriate file? RUU Zip M7 WL JB 50 VZW 1.10.605.10 Decrypted from HTC1 Guru.com (I can't post the actual link do to the forum rules.) The CID and model id match what my phone says.
Thanks for all your help!

factor00 said:
Yes fastboot is working. I can see the phone info still. You said I can just RUU. I didn't realize I could do that. That's fine with me I have no issue with that.
I just re-lock the boot loader and then run the RUU from windows? Would this be the appropriate file? RUU Zip M7 WL JB 50 VZW 1.10.605.10 Decrypted from HTC1 Guru.com (I can't post the actual link do to the forum rules.) The CID and model id match what my phone says.
Thanks for all your help!
Click to expand...
Click to collapse
I haven't done anything RUU in a while, so I don't want to steer you wrong. But I believe you can use decrypted to get everything up and running. Check the general forum for a guide on returning to stock.
Sent from my HTC6525LVW using XDA Premium 4 mobile app

Just remember to keep s-off while running the ruu

Related

HTC DESIRE HD RUU update result bricked phone logo screen HELP

Hi guys!!
I really need your help. after unsuccessful attempt to update my HDT with ruu file (dont know which one) it ended up with white screen. i thought no big deal. i ll fix that but after numerous attempts to return stock i realize that something that i do is not right so help me please.
my HD is locked and first i tried to unlock bootloader on htcdev but my hboot 2.00.027 is no longer support as htcdev claims. it needs to be updated.
This is the RUU file that according to my knowledge matches the requirements of my phone but oviously not.
RUU_Ace_Sense30_S_HTC_WWE_3.12.405.1_Radio_12.65.60.29_26.14.04.28_M_release_225512_signed
i tried with it flash from sd card - it comes to do you want to update? pressed vol.buton +. update in progress and that stuck for over a hour.
tried via computer and usb cabel. after running exe file it stuck on rebooting in bootloader.
tried flash over adb and fastboot command via cmd. fastboot devices shows that phone is connected but it stuck on next command fastboot erase cache.
here are the characteristic of the phone.
ACE PVT SHIP S-ON RL
HBOOT 2.00.0027
MICROP - 0438
RADIO 26.14.04.28_M
eMMc - boot
Sep 7 2011,19:06:24
C:\android>fastboot getvar all
(bootloader) version: 0.5
(bootloader) version-bootloader: 2.00.0027
(bootloader) version-baseband: 26.14.04.28_M
(bootloader) version-cpld: None
(bootloader) version-microp: 0438
(bootloader) version-main: 3.12.405.1
(bootloader) serialno: SH198RX00810
(bootloader) imei: 3xxxxxxxxxx
(bootloader) product: ace
(bootloader) platform: HBOOT-7230
(bootloader) modelid: PD9810000
(bootloader) cidnum: HTC__102
(bootloader) battery-status: good
(bootloader) battery-voltage: 4135mV
(bootloader) partition-layout: Generic
(bootloader) security: on
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: 743ca94a
(bootloader) hbootpreupdate: 11
(bootloader) gencheckpt: 0
(bootloader) region-id: 0
all: Done!
finished. total time: 0.000s
C:\android>
PLEASE HELP ME TO FIND THE RIGHT RUU or any other method that would work.
bear in mind iam unrooted.
What am i supposed to do to fix my phone? any clue?
via RUU or .... ............
If your aiming for a stock rom, Just create a goldcard and try flashing your stock rom.
You can extract the rom.zip file in ruu by
The process:
- Download a RUU from anywhere (you already have one)
- Open/Run the .exe You'll get something like this
- Click the Start button
- Select the Run command and type in: %temp%
- Search for a folder that has a bunch of characters and looks somewhat like this: {XXXXXX-XXXX-XXXX-XXXX-XXXXXXXX} just keep on searching in each folder, if you have patience you'll find it.
- And inside that folder should be another folder that looks the same, and has the format above.
- Find a zip file called rom.zip -
-Rename the rom.zip to PD98IMG.zip
If you already created a goldcard. put the PD98IMG.zip in the root of your sd card
Go to bootloader and pressing -volume and power button.
Rom zip will automatically detected and you will be ask to update.
Hope it helps "newbie here" :fingers-crossed:
Iam not aiming on stock. actually i dont care. i just want my phone back working.
i dont have a goldcard. can i make one with unrooted and locked phone?
i tried with flash from sd card extracted rom and renamed as PD98IMG - it comes to do you want to update? pressed vol.buton up than shows update in progress and stuck for over a hour.
doesent work
thanks for effort
Its easy to create a goldcard, any sd card will do.
Links is http://forum.xda-developers.com/showthread.php?t=970157
if you cannot get your cid just use the attach file goldcard.img below
i dont know if it would work, but since you haven't find any solution yet, you could at least try.
Hope it helps your phone...:fingers-crossed:
charles66 said:
Iam not aiming on stock. actually i dont care. i just want my phone back working.
i dont have a goldcard. can i make one with unrooted and locked phone?
i tried with flash from sd card extracted rom and renamed as PD98IMG - it comes to do you want to update? pressed vol.buton up than shows update in progress and stuck for over a hour.
doesent work
thanks for effort
Click to expand...
Click to collapse
Have you tried with a different sdcard? have you also checked the md5sum or the RUU? maybe you can flash it in fastboot (read the guide in my signature to find out how)
glevitan said:
Have you tried with a different sdcard? have you also checked the md5sum or the RUU? maybe you can flash it in fastboot (read the guide in my signature to find out how)
Click to expand...
Click to collapse
i tried with a other sd card.
i also checked ms5sum - it matches.
i tried flash it from fastboot.
result - negativ.
with sd card it comes do you want to update? yes. and than stuck on updating on a first stage on bootloader and stuck there.
i tried with a goldcard. result the same as with regular sd card.
please read all my tread. i need to fix my phone.

[Q] Problems in updating (4.0.4 to 4.1.1) and going into recovery mode

I tried to update my HTC One X from 4.0.4 to 4.1.1 by OTA. The phone would download the entire update (around 370 MB), then try to install it, but couldn't. This happened several times. Then I downloaded the OTA update zip file and copied it to my phone memory. But now, it wouldn't go into recovery mode (after pressing volume down and power and navigating to recovery). When I press on recovery, it would go to a black screen, showing a phone with an exclamatory sign over it. After some time (maybe 1 or 2 minutes) it would reboot to normal mode with 4.0.4.
So, I think the problem is my phone cannot simply enter recovery mode. Is there any way to install the update by commands through PC?
I'm not really a fan of custom ROMs. Only the stock ROM of JB 4.1.1 will do.
Thanks!
Try resetting your phone from the hboot. (You'll lose all data including apps and sdcard. So backup first)
Then try ota again.
Sent from my One X
athulele said:
Try resetting your phone from the hboot. (You'll lose all data including apps and sdcard. So backup first)
Then try ota again.
Sent from my One X
Click to expand...
Click to collapse
You mean factory reset? Did that. No improvement. Also I ran the RUU for stock ROM of ICS 4.0.4. Had to do that to unbrick it (long story, was trying to flash custom ROM. Was facing the same problem, couldn't enter recovery option). But still, same story, downloads update for 2 hours, then goes back to 4.0.4. I'm in deep **** man!
khalid_saad said:
You mean factory reset? Did that. No improvement. Also I ran the RUU for stock ROM of ICS 4.0.4. Had to do that to unbrick it (long story, was trying to flash custom ROM. Was facing the same problem, couldn't enter recovery option). But still, same story, downloads update for 2 hours, then goes back to 4.0.4. I'm in deep **** man!
Click to expand...
Click to collapse
Have you unlocked your bootloader?
If yes, I will directly give you instructions to update to 4.2.2
athulele said:
Have you unlocked your bootloader?
If yes, I will directly give you instructions to update to 4.2.2
Click to expand...
Click to collapse
I did, but again relocked to go to stock ROM to unbrick via RUU. I can unlock it again and I would appreciate if you tell me how to update to 4.2.2. But I'm afraid the process won't work if it involves going into recovery mode in the phone.
khalid_saad said:
I did, but again relocked to go to stock ROM to unbrick via RUU. I can unlock it again and I would appreciate if you tell me how to update to 4.2.2. But I'm afraid the process won't work if it involves going into recovery mode in the phone.
Click to expand...
Click to collapse
It does involve the recovery mode.
Can you tell me why it wouldn't work?
Sent from my One X
athulele said:
It does involve the recovery mode.
Can you tell me why it wouldn't work?
Sent from my One X
Click to expand...
Click to collapse
Like I said earlier, when I go to bootloader (by holding volume down and power) and then select recovery from the options, a black screen comes with an android photo in the middle, with an exclamatory sign above it. After a couple of minutes, the screen disappears and the phone is restarted. That's what happens every time, I don't know why.
khalid_saad said:
Like I said earlier, when I go to bootloader (by holding volume down and power) and then select recovery from the options, a black screen comes with an android photo in the middle, with an exclamatory sign above it. After a couple of minutes, the screen disappears and the phone is restarted. That's what happens every time, I don't know why.
Click to expand...
Click to collapse
That's not a problem. What you're seeing is the Stock Recovery from HTC. As far as I know, you can't flash stuff from HTC's recovery.
Give me the output of 'fastboot getvar all'
And also while pasting the output, hide your IMEI and Serial No. it may be used for bad purposes by bad people.
athulele said:
That's not a problem. What you're seeing is the Stock Recovery from HTC. As far as I know, you can't flash stuff from HTC's recovery.
Give me the output of 'fastboot getvar all'
And also while pasting the output, hide your IMEI and Serial No. it may be used for bad purposes by bad people.
Click to expand...
Click to collapse
I found an article in the internet telling that if I copy the OTA update .zip file in my phone's memory, then go to recovery and select that file for update, it will update from 4.0.4 to 4.1.1. Sorry I forgot the link, so can't give you the reference.
Anyway, here is the output of 'fastboot getvar all':
(bootloader) version: 0.5a
(bootloader) version-bootloader: 1.12.0000
(bootloader) version-baseband: 2.1204.135.20
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main: 2.17.401.2
(bootloader) serialno: ************
(bootloader) imei: ***************
(bootloader) product: endeavoru
(bootloader) platform: HBOOT-T30S
(bootloader) modelid: PJ461****
(bootloader) cidnum: 11111111
(bootloader) battery-status: good
(bootloader) battery-voltage: 3832mV
(bootloader) devpower: 51
(bootloader) partition-layout: None
(bootloader) security: off
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: None
(bootloader) hbootpreupdate: 2
(bootloader) gencheckpt: 0
all: Done!
finished. total time: 0.810s
khalid_saad said:
I found an article in the internet telling that if I copy the OTA update .zip file in my phone's memory, then go to recovery and select that file for update, it will update from 4.0.4 to 4.1.1. Sorry I forgot the link, so can't give you the reference.
Anyway, here is the output of 'fastboot getvar all':
(bootloader) version: 0.5a
(bootloader) version-bootloader: 1.12.0000
(bootloader) version-baseband: 2.1204.135.20
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main: 2.17.401.2
(bootloader) serialno: ************
(bootloader) imei: ***************
(bootloader) product: endeavoru
(bootloader) platform: HBOOT-T30S
(bootloader) modelid: PJ461****
(bootloader) cidnum: 11111111
(bootloader) battery-status: good
(bootloader) battery-voltage: 3832mV
(bootloader) devpower: 51
(bootloader) partition-layout: None
(bootloader) security: off
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: None
(bootloader) hbootpreupdate: 2
(bootloader) gencheckpt: 0
all: Done!
finished. total time: 0.810s
Click to expand...
Click to collapse
Cool dude! You have a s-off deivce!
Anyway, Backup ALL (Apps, contacts, sdcard) data before you start with the following steps -
1. Keep your bootloader LOCKED.
2. Download this firmware and place it in your fastboot folder. Also download the stock ROM and place it on your device.
3. reboot your phone into fastboot mode
4. Through cmd - fastboot oem rebootRUU
5.You'll have a black screen on the device
6. Just to be sure, flash the firmware zip twice while in RUU mode. (fastboot flash zip firmware.zip)
7. Now go back to fastboot mode ( Power and volume combo)
8. Unlock your bootloader ( please refer HTCDev for instructions)
9. Flash this recovery (fastboot flash recovery recovery.img)
10. Extract the boot.img from the Stock ROM zip and flash it through fastboot (fastboot flash boot boot.img)
11. Go into the recovery. Do a Factory Reset.
12. locate the stock rom and flash it. (if it was erased while unlocking the bootloader, place it again)
13. now reboot
14. If all goes well, you'll boot into stock 4.2.2!
15. if you want to receive further OTA updates (if any)from hTC , flash this recovery.
Hope I helped! Feel free to ask any doubt you have!
athulele said:
Cool dude! You have a s-off deivce!
Anyway, Backup ALL (Apps, contacts, sdcard) data before you start with the following steps -
1. Keep your bootloader LOCKED.
2. Download this firmware and place it in your fastboot folder. Also download the stock ROM and place it on your device.
3. reboot your phone into fastboot mode
4. Through cmd - fastboot oem rebootRUU
5.You'll have a black screen on the device
6. Just to be sure, flash the firmware zip twice while in RUU mode. (fastboot flash zip firmware.zip)
7. Now go back to fastboot mode ( Power and volume combo)
8. Unlock your bootloader ( please refer HTCDev for instructions)
9. Flash this recovery (fastboot flash recovery recovery.img)
10. Extract the boot.img from the Stock ROM zip and flash it through fastboot (fastboot flash boot boot.img)
11. Go into the recovery. Do a Factory Reset.
12. locate the stock rom and flash it. (if it was erased while unlocking the bootloader, place it again)
13. now reboot
14. If all goes well, you'll boot into stock 4.2.2!
15. if you want to receive further OTA updates (if any)from hTC , flash this recovery.
Hope I helped! Feel free to ask any doubt you have!
Click to expand...
Click to collapse
You are freaking awesome dude! I love you!!!!!!!! :laugh:

[Q] HTC one M8 (dual sim) stuck on bootloader! What can I do?

Hello everyone! glad to be a new member of this amazing community! I am a new member with a tough problem, would love if I get ideas on how to solve it.
So After flashing stock unrooted GPe rom as per the most common methods circulating around (changing CID, MID, S-Off, etc), I was thrilled to see the boot splash screen change into google's except that it keeps booting into the bootloader; for some reason I could not get into recovery either (but I flashed TWRP again and it works now)
So as it stands now I have the following:
S-Off
Unlocked
Software status: Official
Working TWRP (which keeps saying NO OS IS INSTALLED)
Unable to mount /data (whatever that means) + "error: closed" when attempting to sideload the RUU roms via ADB
I did not install any firmware or kernels
and whenever I try to boot the OS I get put back in bootloader over and over.
As far as im concerned this phone seems bricked for me, but im also new so I wouldn't know, having said that, I am open for the most radical of options and procedures to get this working.
Thank you all in advance!
Flash it again via adb, the flashing command must be executed twice.
I get an error "E:Unable to mount '/Data'" as soon as I open up the sideload option. when attempting to sideload I get "error: closed". I am starting to sense I have a problem with my storage. what to do next?
Thank you so much for your reply!
Megaliths said:
I get an error "E:Unable to mount '/Data'" as soon as I open up the sideload option. when attempting to sideload I get "error: closed". I am starting to sense I have a problem with my storage. what to do next?
Thank you so much for your reply!
Click to expand...
Click to collapse
That unrooted GPE was for dual sim? I see you have a dual sim.
Make a screenshot.
Details about the ROM would help.
Do a fastboot getvar all command also.
Actually I don't know if the Rom is for dual sim or not, I figured as long as I get CID and MID right it should fit? pardon my ignorance on the matter. ill post a screenshot as soon as possible!
Getvar all:
C:\Users\Megalith\Desktop\One_M8_All-In-One_Kit_v\data>fastboot getvar all
(bootloader) version: 0.5
(bootloader) version-bootloader: 3.19.0.0000
(bootloader) version-baseband: 1.21.213311491.A04G
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main: 3.11.1700.5
(bootloader) version-misc: PVT SHIP S-OFF
(bootloader) serialno:
(bootloader) imei:
(bootloader) imei2:
(bootloader) meid:
(bootloader) product: m8_dugl
(bootloader) platform: hTCBmsm8974
(bootloader) modelid: 0P6B17000
(bootloader) cidnum: GOOGL001
(bootloader) battery-status: good
(bootloader) battery-voltage: 0mV
(bootloader) partition-layout: Generic
(bootloader) security: off
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: c88f4560
(bootloader) hbootpreupdate: 11
(bootloader) gencheckpt: 0
all: Done!
finished. total time: 0.017s
Megaliths said:
Getvar all:
C:\Users\Megalith\Desktop\One_M8_All-In-One_Kit_v\data>fastboot getvar all
(bootloader) version: 0.5
(bootloader) version-bootloader: 3.19.0.0000
(bootloader) version-baseband: 1.21.213311491.A04G
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main: 3.11.1700.5
(bootloader) version-misc: PVT SHIP S-OFF
(bootloader) serialno:
(bootloader) imei:
(bootloader) imei2:
(bootloader) meid: 00000000000000
(bootloader) product: m8_dugl
(bootloader) platform: hTCBmsm8974
(bootloader) modelid: 0P6B17000
(bootloader) cidnum: GOOGL001
(bootloader) battery-status: good
(bootloader) battery-voltage: 0mV
(bootloader) partition-layout: Generic
(bootloader) security: off
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: c88f4560
(bootloader) hbootpreupdate: 11
(bootloader) gencheckpt: 0
all: Done!
finished. total time: 0.017s
Click to expand...
Click to collapse
Delete the IMEI.
OP - Do you want it back to Sense?
EddyOS said:
OP - Do you want it back to Sense?
Click to expand...
Click to collapse
I really prefer to get GPE working but sense is better than a bricked phone.
Also, thanks for the replies!
EddyOS said:
OP - Do you want it back to Sense?
Click to expand...
Click to collapse
Come to think about it now, I'd rather go to stock now if it all possible.
Megaliths said:
I really prefer to get GPE working but sense is better than a bricked phone.
Also, thanks for the replies!
Click to expand...
Click to collapse
Megaliths said:
Come to think about it now, I'd rather go to stock now if it all possible.
Click to expand...
Click to collapse
OK. First things first, did the GPe ROM ever work? The reason I ask it was designed for the single-SIM M8 so don't know if it worked with the dual-SIM version. If not, we should be OK to get back to stock...
EddyOS said:
OK. First things first, did the GPe ROM ever work? The reason I ask it was designed for the single-SIM M8 so don't know if it worked with the dual-SIM version. If not, we should be OK to get back to stock...
Click to expand...
Click to collapse
It never booted up correctly no. I'd love if you can help me go to stock with such a messed up state my phone had gotten into.
We should be able to sort things out, but I'll need to get to a proper PC and get links together
EddyOS said:
We should be able to sort things out, but I'll need to get to a proper PC and get links together
Click to expand...
Click to collapse
Thank you so much!
OK, this isn't particularly straight forward but should hopefully work...
Download the following files and place in your fastboot folder:
- Dual-SIM RUU - https://drive.google.com/file/d/0B17smFr95pleaW9iTFBiSUE2OVE/view?usp=sharing (rename to anything you want but I'd recommend ruu.zip, not ruu.zip.zip obviously!)
- htc_fastboot - https://www.androidfilehost.com/?fid=95897840722646249
- Sense FW - https://www.androidfilehost.com/?fid=23329332407589439 (again, rename to anything but I'd recommend firmware.zip)
1. First things first, boot into fastboot and set your CID to Super CID - fastboot oem writecid 11111111
2. Once done, reboot the bootloader and confirm it's done - fastboot reboot-bootloader
3. Assuming it's done, boot the phone into RUU mode - fastboot oem rebootRUU
4. Once in RUU mode, flash the firmware package - fastboot flash zip firmware.zip
5. It'll fail the first time and reboot. Do the exact same command again once back in RUU mode - fastboot flash zip firmware.zip
6. Once finished, reboot back to the bootloader to confirm it's on the white 'Sense' version - fastboot reboot-bootloader
7. Assuming it's done, reboot into RUU mode again - fastboot oem rebootRUU
8. Now flash the RUU using the HTC fastboot version - htc_fastboot flash zip ruu.zip
9. This will go through a few passes but once finished reboot to the bootloader - fastboot reboot-bootloader
10. Once back at the bootloader, disconnect the phone and go into stock recovery
11. Once in stock recovery, hold power and press volume up and once the menu appears do a factory reset
12. Once complete, reboot the phone
It should now boot back into the normal Sense ROM. Now if you changed your MID to the GPe one you'll need to re-root your phone and change it back using the guide by @scotty1223 HERE but if you didn't change it then you're good to go!
EddyOS said:
OK, this isn't particularly straight forward but should hopefully work...
Download the following files and place in your fastboot folder:
- Dual-SIM RUU - https://drive.google.com/file/d/0B17smFr95pleaW9iTFBiSUE2OVE/view?usp=sharing (rename to anything you want but I'd recommend ruu.zip, not ruu.zip.zip obviously!)
- htc_fastboot - https://www.androidfilehost.com/?fid=95897840722646249
- Sense FW - https://www.androidfilehost.com/?fid=23329332407589439 (again, rename to anything but I'd recommend firmware.zip)
1. First things first, boot into fastboot and set your CID to Super CID - fastboot oem writecid 11111111
2. Once done, reboot the bootloader and confirm it's done - fastboot reboot-bootloader
3. Assuming it's done, boot the phone into RUU mode - fastboot oem rebootRUU
4. Once in RUU mode, flash the firmware package - fastboot flash zip firmware.zip
5. It'll fail the first time and reboot. Do the exact same command again once back in RUU mode - fastboot flash zip firmware.zip
6. Once finished, reboot back to the bootloader to confirm it's on the white 'Sense' version - fastboot reboot-bootloader
7. Assuming it's done, reboot into RUU mode again - fastboot oem rebootRUU
8. Now flash the RUU using the HTC fastboot version - htc_fastboot flash zip ruu.zip
9. This will go through a few passes but once finished reboot to the bootloader - fastboot reboot-bootloader
10. Once back at the bootloader, disconnect the phone and go into stock recovery
11. Once in stock recovery, hold power and press volume up and once the menu appears do a factory reset
12. Once complete, reboot the phone
It should now boot back into the normal Sense ROM. Now if you changed your MID to the GPe one you'll need to re-root your phone and change it back using the guide by @scotty1223 HERE but if you didn't change it then you're good to go!
Click to expand...
Click to collapse
That is amazing thank you, ill try it and get back to you asap.
I have two questions:
Will I still get OTAs even if I don't have the original CID and MID? (I remember the original CID which is J15 but I can't remember the mid).
Also, I am currently on custom recovery and in your guide above I do not see anything about flashing stock recovery, should I do that first?
Thank you again!
The RUU flashes everything stock, so it'll overwrite it all
I'd change the CID back to stock once it's all working again but the MID I'm not sure on so I'll see if I can find out for you
At step 8 I get an error "DNS server not authoritative for zone", how to resolve that?
Nvm I resolved the DNS thin, but now I get error 41 model id check fail. It is probably because of bad MID isn't it?
Thank you again for helping me, I hope it is not much trouble.

Fastboot

I need to unselect fastboot in my settings, but my phone wont even turn on pass the htc logo. Can someone please help me?
You don't really need to unselect "Fast boot" in settings. Its not even an option in Settings anymore in Lollipop or Marshmallow.
Even if you are still on Kitkat (few people are) the only thing that "Fast boot" affected, is that it prevented booting into bootloader from a power-off condition. But if you force a reboot (which is distinctly different from power-off), you can still get to bootloader:
1) Hold power + vol up until phone reboots (may take a minute or more, if you are stuck on the HTC logo screen)
2) Once the screen goes dark to reboot (but before the HTC logo screen comes back up) let go of the buttons, and hold only the vol down button. Don't let go of vol down, until you see the bootloader screen.
3) If it didn't work, you just didn't get the timing right. You either started pressing vol down too late, or let go too early. Just repeat steps 1 & 2 above until you get it right.
Thank you for help. I already unlock my m8(by HTC dev) and I get recovery and install from recovery superSU zip file. But i cant finished superSU parts(so I am still without s-off and root?), because my telephone still cant load android(I am still on ``HTC one`` logo). So question can I put original firmware into memory card and reinstall all system?
dzefas said:
Thank you for help. I already unlock my m8(by HTC dev) and I get recovery and install from recovery superSU zip file. But i cant finished superSU parts(so I am still without s-off and root?), because my telephone still cant load android(I am still on ``HTC one`` logo). So question can I put original firmware into memory card and reinstall all system?
Click to expand...
Click to collapse
Many folks get fail to boot after trying to root; due to using an old SuperSU version. If the phone is on Marshmallow (Android 6), you need SuperSU 2.52 or later (2.65 is recommended as the latest stable version).
If this is the case for you (on MM and used an old version SuperSU) then flashing SuperSU 2.65 should allow the phone to boot (and with root).
You should also use current version TWRP 3.0
yes i am using TWRP 3.0.2 and superSU version is 2.65. I am still stuck on `HTC ONE logo`.
dzefas said:
So question can I put original firmware into memory card and reinstall all system?
Click to expand...
Click to collapse
Probably your best bet is to restore a stock nandroid that matches your version.
You didn't make a backup in TWRP before rooting? You should always do that, for this very reason (in case you run into problems and need to restore).
For more specific help on what version, do fastboot getvar all, and post the results (delete IMEI and serial number before posting).
---------- Post added at 03:16 PM ---------- Previous post was at 03:12 PM ----------
dzefas said:
yes i am using TWRP 3.0.2 and superSU version is 2.65. I am still stuck on `HTC ONE logo`.
Click to expand...
Click to collapse
Its not clear, were those the versions you used to begin with, or you tried them after my recommendation?
I tried those versions before your recommendations.
after several tryings, telephone trying load. I mean 'Android is starting optimizing app 21 of 133'
And still after optimizining stuck on ``green HTC``...even i can regulate sound, but this is it.
(bootloader) version: 0.5
(bootloader) version-bootloader: 3.19.0.0000
(bootloader) version-baseband: 1.29.214500021.12G
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main: 6.12.401.4
(bootloader) version-misc: PVT SHIP S-ON
(bootloader) serialno:
(bootloader) imei:
(bootloader) imei2: Not Support
(bootloader) meid: 00000000000000
(bootloader) product: m8_ul
(bootloader) platform: hTCBmsm8974
(bootloader) modelid: 0P6B10000
(bootloader) cidnum: HTC__102
(bootloader) battery-status: good
(bootloader) battery-voltage: 0mV
(bootloader) partition-layout: Generic
(bootloader) security: on
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: 76df2b54
(bootloader) hbootpreupdate: 11
(bootloader) gencheckpt: 0
all: Done!
So question can I put original firmware into memory card and reinstall all system?
dzefas said:
So question can I put original firmware into memory card and reinstall all system?
Click to expand...
Click to collapse
Not firmware but a RUU zip.
Note : MUST relock bootloader
Boot to fastboot/bootloader mode then run command in terminal
fastboot oem lock
What you need :
1. a MicroSD
2. Download the 6.12.401.4 RUU zip - https://www.androidfilehost.com/?fid=24369303960687057
3. Rename the file to 0P6BIMG.zip (that's a zero not "O")
4. Put the 0P6BIMG.zip on your microSD
5. Boot your device to bootloader/fastboot then select hboot, it will scan the update zip and ask whether to update - volume up to select yes
6. Let it do its stuff
7. Once completed, reboot
8. Delete the 0P6BIMG.zip on your microSD (or remove the microSD)
9. done
I to do relock, but still cant find right file in microSD card...why? I check several time of file name...
And now telephone cant even load himself, recovery etc. How to back from RELOCKED?
dzefas said:
I to do relock, but still cant find right file in microSD card...why? I check several time of file name...
Click to expand...
Click to collapse
Having the bootloader unlocked or not (relocked, locked) , has nothing to do with it finding the file. It will find it either way (but fail to install if bootloader is unlocked).
You sure you named the file properly (first character is "zero" not letter "O")?
Also, make sure you turned off the Windows option to hide file extensions (which is ON by default). Otherwise, you may have named it 0P6BIMG.zip.zip and not know it.

HTC with locked internal memory

Folks
I need help to solve a problem.
I bought a HTC One M8x and decided to set up a rom custon. I study the subject before. I took the program kit available for the M8 and follow all the steps to unlock. All this function normally, however when installing the ROM custon the device just gave error. I was exploring the tool I ended up pressing and making procedures that were not listed, but apparently did not issue before starting the installation made the backup and then wipe. I started the procedure to install, entered the install section and located the ROM and sent install. After a while appeared an error saying that the installation was not possible, I managed to recover the backup, but the phone was not the same. I realized that my internal memory is no longer visible, I can not download pictures or audios in whatsapp, another thing I noticed is that the file manager also does not provide the internal memory (directories, programs, and others). When I try to synchronize your phone with your computer to the same thing, I can see the micro SD, but can not see the internal memory. I possibly when I was digging the Recovery program just blocking the internal memory and wanted to know how do to reverse. Does anyone have any ideas.
Do you have access to bootloader? if yes. You can try to restore your phone with HTC RUU
ddfilho said:
I took the program kit available for the M8 and follow all the steps to unlock. All this function normally, however when installing the ROM custon the device just gave error.
Click to expand...
Click to collapse
Using the (now outdated) toolkit was a mistake. Whenever modding these devices, you need to research the current methods applicable to the current state of the phone, not methods from 2 years ago (and all the toolkits have not been updated in that long or more).
The toolkit installs an obsolete version of TWRP, and that is probably why the ROM is failing to flash. It probably also wiped out your OS version on bootloader screen and getvar (not a major issue, but an inconvenience if you want to determine the firmware number).
You should update to more current version of TWRP. But you'll probably need to solve the issue of your internal storage first, which is apparently been corrupted. Go into TWRP, and try the option in Wipe to "Format Data" (button next to "Advanced"). This usually fixes the corrupt internal storage issue.
Also do fastboot getvar all, and post the results, so we can see more info about the phone, and more properly provide guidance. Delete IMEI and serial number before posting.
I have access to the bootloader but do not know run this action. Could you tell me where I can walkthrougt to do so.
Thank you for your help
Pardon
Now that saw the second message. I will perform this procedure now
Friend
Your solution worked perfectly.
I wanted your help to make the second action, I entered the bootloader and accessed the fastboot but did not find the getvar option. Could you tell me how to do it.
I found the TWRP 3.0.2, I believe it is the last version but need help because I believe that the update version is not simple, I installed the 2.7.0.2 version.
Thanks again
ddfilho said:
I wanted your help to make the second action, I entered the bootloader and accessed the fastboot but did not find the getvar option. Could you tell me how to do it.
Click to expand...
Click to collapse
This isn't an option on the phone, if that is what you mean. Its a fastboot command issued from your PC, and you'd know how to issue a fastboot command if you unlocked the bootloader via HTCDev.com, instead of letting the toolkit do it for you. Which is another reason I don't like the toolkits: they shortcut the learning process, and leave you without the skills to solve basic problems, which almost inevitably happen.
You're going to need to figure out where fastboot.exe was installed during the bootloader unlock process. Once you've found that, you can then:
1) Connect phone to PC, booted into bootloader-fastboot mode
2) On PC, open a window for the folder that contains fastboot.exe
3) Hover mouse cursor over the window, and Shift+Right Mouse button, then select "Open command window here" and this will open up Command Prompt to the fastboot directory
4) In Command Prompt window, type: fastboot getvar all
5) You will see output with details about the phone, to copy the desired text, right click on the command window, select Edit>Mark, then highlight the desired text (getvar output) and press Enter. Then paste the text.
6) Be sure to delete IMEI and serial number from getvar output before posting it here
ddfilho said:
I found the TWRP 3.0.2, I believe it is the last version but need help because I believe that the update version is not simple, I installed the 2.7.0.2 version.
Click to expand...
Click to collapse
Exact TWRP version depends on your current firmware, which we can determine from the getvar output above.
Once we've determined the proper TWRP version, its easily installed by putting the file in your fastboot folder, and flashing with fastboot command. Again, we see how valuable it is to know how to use fastboot. But don't try that, until we've determined the proper version from getvar output.
I managed to perform the procedure now. See the information:
(bootloader) version: 0.5
(bootloader) version-bootloader: 3.19.0.0000
(bootloader) version-baseband: 1.29.214500021.24_2G
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main:
(bootloader) version-misc: PVT SHIP S-ON
(bootloader) serialno:
(bootloader) imei:
(bootloader) imei2: Not Support
(bootloader) meid: 00000000000000
(bootloader) product: m8_ul
(bootloader) platform: hTCBmsm8974
(bootloader) modelid: 0P6B11000
(bootloader) cidnum: HTC__621
(bootloader) battery-status: good
(bootloader) battery-voltage: 0mV
(bootloader) partition-layout: Generic
(bootloader) security: on
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: 205bdca3
(bootloader) hbootpreupdate: 11
(bootloader) gencheckpt: 0
all: Done!
finished. total time: 0.017s
ddfilho said:
I managed to perform the procedure now. See the information:
(bootloader) version-baseband: 1.29.214500021.24_2G
(bootloader) version-main:
Click to expand...
Click to collapse
As I suspected, your firmware number (version-main) info was wiped out by using an obsolete version of TWRP (known bug). But luckily I know the radio number corresponds to Marshmallow firmware.
Flash TWRP 3.0.2 using the fastboot install method here. No need to install Android SDK, or drivers noted in the instructions, since you already have fastboot setup (and you're a fastboot expert now ); and not need to reboot using adb, if you do it using the button combo other otherwise.
After getting the updated TWRP version installed, you should be able to put the desired custom ROM on the phone, and flash it. If not, take note of any error messages or other behaviors, and post them here.
redpoint73 said:
As I suspected, your firmware number (version-main) info was wiped out by using an obsolete version of TWRP (known bug). But luckily I know the radio number corresponds to Marshmallow firmware.
Flash TWRP 3.0.2 using the fastboot install method here. No need to install Android SDK, or drivers noted in the instructions, since you already have fastboot setup (and you're a fastboot expert now ); and not need to reboot using adb, if you do it using the button combo other otherwise.
After getting the updated TWRP version installed, you should be able to put the desired custom ROM on the phone, and flash it. If not, take note of any error messages or other behaviors, and post them here.
Click to expand...
Click to collapse
Folks
Thank you for your help
I managed to update TWRP following the instructions, but when I tried to install the ROM did not succeed.
It gave an error as if he could not open the file or install, see the message:
Error opening: `/and-sec/uuuuuuuu.uuu'(I/O error) ===> Several lines with mensagem.
You know how I can be able to install any rom?
In TWRP go to WIPE then select Format data, type yes
Then go to REBOOT select recovery ... now try again to install ROM

Categories

Resources