Related
Hi I have this problem that OTA download new update and than it was installing when it reboot it never come back it is now stuck on galaxy note II screen. things i did is tring to install stock rom( KIES_HOME_I317UCALJ2_I317ATTALJ2_215287_REV04_user_low_ship.tar.md5) and it complete pass but when it reboot same thing it is stuck on screen. i tried to clean cache but it doesn't boot in to recovery. now i am stock i need help. just want to is it partion got damaged. does anybody have complete package rom( means PIT file, PDA file, CSC file, Phone file, bootloader file) i tried looking for file i found links of hotfile but hotfile is no more i also found couple of dropbox links which is not active no more can some one help me on this.
Thank you
ash0621 said:
Hi I have this problem that OTA download new update and than it was installing when it reboot it never come back it is now stuck on galaxy note II screen. things i did is tring to install stock rom( KIES_HOME_I317UCALJ2_I317ATTALJ2_215287_REV04_user_low_ship.tar.md5) and it complete pass but when it reboot same thing it is stuck on screen. i tried to clean cache but it doesn't boot in to recovery. now i am stock i need help. just want to is it partion got damaged. does anybody have complete package rom( means PIT file, PDA file, CSC file, Phone file, bootloader file) i tried looking for file i found links of hotfile but hotfile is no more i also found couple of dropbox links which is not active no more can some one help me on this.
Thank you
Click to expand...
Click to collapse
Go to this thread.
http://forum.xda-developers.com/showthread.php?t=2502464
Download
4.3 Param.bin and Tz.img
http://d-h.st/OYC
Unzip, Boot into Download mode, Open ODIN, put tar file in PDS slot, click Start.
ODIN under Section 8 hers
http://forum.xda-developers.com/showthread.php?t=1987541
dicksteele said:
Go to this thread.
http://forum.xda-developers.com/showthread.php?t=2502464
Download
4.3 Param.bin and Tz.img
http://d-h.st/OYC
Unzip, Boot into Download mode, Open ODIN, put tar file in PDS slot, click Start.
ODIN under Section 8 hers
http://forum.xda-developers.com/showthread.php?t=1987541
Click to expand...
Click to collapse
Thanks for reply
I tried 4.3 param.bin it works phone come back to live
now its is on 4.1.2
baseband i317ucama4
kernal :3.0.31-578342
build: JZ054K.I317UCAMA4
NOW WHEN CLICK ON SOFTWARE UPDATE IT SAYS NO fIRMWARE
SI HOW CAN I UPDATE TO 4.3
THANKS
ash0621 said:
Thanks for reply
I tried 4.3 param.bin it works phone come back to live
now its is on 4.1.2
baseband i317ucama4
kernal :3.0.31-578342
build: JZ054K.I317UCAMA4
NOW WHEN CLICK ON SOFTWARE UPDATE IT SAYS NO fIRMWARE
SI HOW CAN I UPDATE TO 4.3
THANKS
Click to expand...
Click to collapse
Sweet.
Go here
http://forum.xda-developers.com/showthread.php?t=2589891
EDIT: Assuming you are ATT user
I ran into the same problem. However, after flashing 4.3param_tz it puts me back to 4.1.1. How do I upgrade to 4.1.2? If I try doing an OTA to 4.1.2, the phone reboots after downloading, installs and then hangs again at the Samsung Galaxy Note II screen.
ash0621 said:
Thanks for reply
I tried 4.3 param.bin it works phone come back to live
now its is on 4.1.2
baseband i317ucama4
kernal :3.0.31-578342
build: JZ054K.I317UCAMA4
NOW WHEN CLICK ON SOFTWARE UPDATE IT SAYS NO fIRMWARE
SI HOW CAN I UPDATE TO 4.3
THANKS
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=2589891
-》Sent from my mind to your screen.
THANK YOU!
dicksteele said:
Go to this thread.
http://forum.xda-developers.com/showthread.php?t=2502464
Download
4.3 Param.bin and Tz.img
http://d-h.st/OYC
Unzip, Boot into Download mode, Open ODIN, put tar file in PDS slot, click Start.
ODIN under Section 8 hers
http://forum.xda-developers.com/showthread.php?t=1987541
Click to expand...
Click to collapse
I was worried that my phone was going to be a paperweight. My phone wasn't able to get past the Galaxy Note II logo. All that I was able to do was go into download mode and flash anything but i couldn't go into recovery mode. After flashing 4.3 param .tz.tar my phone was finally able to boot up. Thanks so much.
acowsaysmoo said:
I was worried that my phone was going to be a paperweight. My phone wasn't able to get past the Galaxy Note II logo. All that I was able to do was go into download mode and flash anything but i couldn't go into recovery mode. After flashing 4.3 param .tz.tar my phone was finally able to boot up. Thanks so much.
Click to expand...
Click to collapse
Sweet. It's hard as hell to kill these phones. Luckily someone tried that trick. I was in the same boat last month when I was testing.
Sent from my SAMSUNG-SGH-I317 using XDA Premium 4 mobile app
Hi, i bought a note 2 and it was stuck in galaxy note II Logo i did that and now it is stuck in samsung logo, the guy that i bought it said that it was running OTA 4.3 and they root it and tried to downgrade it. i put twrp recovery and when i tried to do a factory reset it said failed.
tito07dr said:
Hi, i bought a note 2 and it was stuck in galaxy note II Logo i did that and now it is stuck in samsung logo, the guy that i bought it said that it was running OTA 4.3 and they root it and tried to downgrade it. i put twrp recovery and when i tried to do a factory reset it said failed.
Click to expand...
Click to collapse
Just start from scratch
http://forum.xda-developers.com/showthread.php?t=2618447
Then when you get to Post #3 steps, you can just flash a stock rooted 4.3 Rom instead of doing the 4.3 OTA again.
[QRCODE][/QRCODE]
dicksteele said:
Just start from scratch
http://forum.xda-developers.com/showthread.php?t=2618447
Then when you get to Post #3 steps, you can just flash a stock rooted 4.3 Rom instead of doing the 4.3 OTA again.
Click to expand...
Click to collapse
i flashed TWRP 2.6.3.1 , then installed i317-cwm-ucubmk6-rooted-odex.zip via twrp, it boot up but now it is stucked in att logo.
PD: when i tried to factory reset twrp said failed, only can clean cache :S.
---------- Post added at 05:15 PM ---------- Previous post was at 04:53 PM ----------
tito07dr said:
[QRCODE][/QRCODE]
i flashed TWRP 2.6.3.1 , then installed i317-cwm-ucubmk6-rooted-odex.zip via twrp, it boot up but now it is stucked in att logo.
PD: when i tried to factory reset twrp said failed, only can clean cache :S.
Click to expand...
Click to collapse
i solved it, just wipe data, them did factory resest and now it power up!!
Thx a lot bro!
Hi, i have another problem i dont know if it is a software or hardware issue, all the sensors are like off, light, proximity, gyro, all!,
pic attached
tito07dr said:
Hi, i have another problem i dont know if it is a software or hardware issue, all the sensors are like off, light, proximity, gyro, all!,
pic attached
Click to expand...
Click to collapse
hey any1 can help me with this problem? i tested the board with other light/proximity sensor and it didnt work.
im running i317-cwm-ucubmk6-rooted-odex.zip with
thanks!
tito07dr said:
hey any1 can help me with this problem? i tested the board with other light/proximity sensor and it didnt work.
im running i317-cwm-ucubmk6-rooted-odex.zip with
thanks!
Click to expand...
Click to collapse
What app are you using. I'm running the same ROM
dicksteele said:
What app are you using. I'm running the same ROM
Click to expand...
Click to collapse
nothing, I just flashed it.
tito07dr said:
I'm oem, nothing, I just flashed it.
Click to expand...
Click to collapse
What application are you using to test the sensors, or what is the screenshot of
dicksteele said:
What application are you using to test the sensors, or what is the screenshot of
Click to expand...
Click to collapse
*#0*#, the samsung test mode
Hi All. I've been working on this Note 2 for the past 48 hours (maybe 5-6 hours each day), but still cannot figured out what's wrong with it. I have downloaded the stock Rogers rom 4.4.2 and it flashed perfectly fine and when it reboot, then stuck at Samsung screen. I've tried method like removed battery then wipe data/factory reset, then wipe cache partition but to no avail.
The stock rom I used is I317MVLUDNF3_I317MOYADNF3_I317MVLUDNF3_HOME.tar, not sure if this is correct.
I also get these error message:
E:failed to mount /efs (invalid argument)
Anyone can help me out. I would greatly appreciate.
Thanks
You need the ne5 version the nf3 is for the n7105
Do you know where I can download it?
terpin32 said:
You need the ne5 version the nf3 is for the n7105
Click to expand...
Click to collapse
I was on the omni rom and decided to change my recovery when this happened.
It wouldnt boot past the samsung screen. I cannot get into recovery but I can get into download mode.
I know one possible fix is flashing the stock image through Odin but I cannot find the stock images. All the links are dead.
Anything will help.
Also if there is anybody willing to walk me through this real time, feel free to message me and we can chat on google hangouts.
krayzielilsmoki said:
Also if there is anybody willing to walk me through this real time, feel free to message me and we can chat on google hangouts.
Click to expand...
Click to collapse
What recovery are you using ?
Since you can get in to recovery, did you try restoring any of your previous backups ?
Are you already on 4,3 bootloader ?
You can download thr stock 4.3 firmware from here : http://www.sammobile.com/firmwares/1/?model=SGH-T889&pcode=0
You will need an account on sammobile though.
ciphercodes said:
What recovery are you using ?
Since you can get in to recovery, did you try restoring any of your previous backups ?
Are you already on 4,3 bootloader ?
You can download thr stock 4.3 firmware from here : http://www.sammobile.com/firmwares/1/?model=SGH-T889&pcode=0
You will need an account on sammobile though.
Click to expand...
Click to collapse
I tried the sammobile website but the downloaded files didnt work for me. I finally downloaded the T889UVALL4 factory image from this thread:
http://forum.xda-developers.com/showthread.php?t=2102380 but now im stuck in a bootloop. ill see if I can get into recovery now and if so Ill just flash twrp that I have on my sd card
still didnt want to go into recovery but I flashed CWM recovery through odin and I was able to go into it. Now ill flash the TWRP and see if I can flash my rom.
krayzielilsmoki said:
I tried the sammobile website but the downloaded files didnt work for me. I finally downloaded the T889UVALL4 factory image from this thread:
http://forum.xda-developers.com/showthread.php?t=2102380 but now im stuck in a bootloop. ill see if I can get into recovery now and if so Ill just flash twrp that I have on my sd card
Click to expand...
Click to collapse
How did you flash T889UVALL4 ?
Most likely your phone is on a newer(4.3) bootloader and flashing an older bootloader caused the boot loop.
I am very certain that flashing 4.3 stock image will resolve this problem.
ciphercodes said:
How did you flash T889UVALL4 ?
Most likely your phone is on a newer(4.3) bootloader and flashing an older bootloader caused the boot loop.
I am very certain that flashing 4.3 stock image will resolve this problem.
Click to expand...
Click to collapse
That might be it, since I was on 4.4.2 before. Do you know if there are better hosting sites for the download file because the ones on that site take 6 hours to download.
krayzielilsmoki said:
That might be it, since I was on 4.4.2 before. Do you know if there are better hosting sites for the download file because the ones on that site take 6 hours to download.
Click to expand...
Click to collapse
mluciano has uploaded the Stock Rooted ROM(Mr Robinsons) image on his dropbox, if you want stock rooted you can download it from here.
Not sure how fast this download would be.
https://www.dropbox.com/sh/lf54pmlxyrilzlx/xWF6hmlpAH
http://forum.xda-developers.com/showthread.php?p=49356729&highlight=dropbox#post49356729
ciphercodes said:
mluciano has uploaded the Stock Rooted ROM(Mr Robinsons) image on his dropbox, if you want stock rooted you can download it from here.
Not sure how fast this download would be.
https://www.dropbox.com/sh/lf54pmlxyrilzlx/xWF6hmlpAH
http://forum.xda-developers.com/showthread.php?p=49356729&highlight=dropbox#post49356729
Click to expand...
Click to collapse
Thank you so much! that rooted one worked perfect. My phone booted completely. And the file downloaded fairly quick.
krayzielilsmoki said:
Thank you so much! that rooted one worked perfect. My phone booted completely. And the file downloaded fairly quick.
Click to expand...
Click to collapse
Glad to know it worked.
I'm trying to downgrade my i747 from CM11 back to stock AT&T firmware but I'm unable to. I've done hours of searching and reading posts, coming up with dead ends.. I'm hoping someone can point me in the right direction.
I can't seem to find an official original AT&T image, I did find a "rooted leaked" image.. but when I try to flash it with Oden it fails and the phone says "SW New Check Fail: Fused 2 > binary 0"
I ran the triangle away, tried a few different roms... I can re-image CM but not anything older. Is there a thread that explains where I can find the proper AT&T stock rom and roll back from CM11?
If you have the stock 4.3 bootloader, you cannot use Odin to flash a stock AT&T 4.3 ROM because AT&T never made a flashable 4.3 ROM available. AT&T only made 4.3 available as an OTA update to an existing ROM.
Thanks, so what are my options if any? I installed the CM11 through their http://get.cm site so I'm not sure what exactly they're doing but the end result is I have CM11, ODIN for the updater, and CWM. Can I downgrade to an older version then and just perform carrier updates to 4.3? If not is it safe to flash some other third party ROM? Or am I stuck on CM11?
-Keith
Boot into download mode and let us know what it says on the screen. This will help us determine if you have the 4.3 bootloader on your phone.
Download mode says:
ODIN MODE
Product Name: SGH-I747
Custom Binary Download: Yes (1 Counts)
Current Binary: Custom
System Status: Official
Qualcom Secureboot: Enable
Warranty Bit: 1
Bootloader AP SWREV: 2
audit13 said:
Boot into download mode and let us know what it says on the screen. This will help us determine if you have the 4.3 bootloader on your phone.
Click to expand...
Click to collapse
I'm thinking of trying the approach that I found here:
http://forum.xda-developers.com/showthread.php?t=2658486
Unless any reason's why I shouldn't, it seems people have been successful with that pseudo 'stock' build.
Based on your download info screen, you have the 4.3 bootloader and the link you provided would be a good choice.
If you didn't have the 4.3 bootloader, you could have flashed a stock 4.1.1 ROM via Odin. With a 4.3 bootloader, you cannot use Odin.
I tried that link but the flash failed..
format() expects 3 args, got 5
E:Error in /external_sd/ATT_i747_UCUEMJB_StockRestore_CWM_2282014.zip
(Status 7)
Installation Aborted.
Ugh..
Status 7 errors can be caused by using an outdated recovery.
I have 6.0.4.7 installed and downloaded the ZIP that says it's for that version but I keep getting the same error.
Maybe the ROM download is corrupt?
kelkin said:
I have 6.0.4.7 installed and downloaded the ZIP that says it's for that version but I keep getting the same error.
Click to expand...
Click to collapse
Did you verify the MD5 of the zip you downloaded? I haven't seen any other report of this not working as it is the definitive solution for returning to stock 4.3.It's possible your download wasn't complete or, as Audit suggested, the zip was corrupted in some way.
I downloaded a different recovery as suggested and was able to flash that way. I'm finally back on the pseudo-stock AT&T firmware and aside from one strange popup everything seems to be working great. Thanks for the help everyone,
-Keith
Larry2999 said:
Did you verify the MD5 of the zip you downloaded? I haven't seen any other report of this not working as it is the definitive solution for returning to stock 4.3.It's possible your download wasn't complete or, as Audit suggested, the zip was corrupted in some way.
Click to expand...
Click to collapse
kelkin said:
I downloaded a different recovery as suggested and was able to flash that way. I'm finally back on the pseudo-stock AT&T firmware and aside from one strange popup everything seems to be working great. Thanks for the help everyone,
-Keith
Click to expand...
Click to collapse
Hey guys I am in pretty the same situation but I can't any other recovery to stick. I can flash and get the pass but it always boots back into cwm 6.0.3.6. Any ideas?
Sent from my SM-N900T using XDA Premium 4 mobile app
donutkidd said:
Hey guys I am in pretty the same situation but I can't any other recovery to stick. I can flash and get the pass but it always boots back into cwm 6.0.3.6. Any ideas?
Sent from my SM-N900T using XDA Premium 4 mobile app
Click to expand...
Click to collapse
Are you flashing via Odin or from CWM? Philz Touch can be flashed from either (i.e. the zip for flashing from an SD card and tar for Odin).
audit13 said:
Are you flashing via Odin or from CWM? Philz Touch can be flashed from either (i.e. the zip for flashing from an SD card and tar for Odin).
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=2824065
This is currently where im at and what I've tried.
Sent from my SM-N900T using XDA Premium 4 mobile app
donutkidd said:
http://forum.xda-developers.com/showthread.php?t=2824065
This is currently where im at and what I've tried.
Sent from my SM-N900T using XDA Premium 4 mobile app
Click to expand...
Click to collapse
I assume you can boot into download mode so use the latest tar version of Philz to flash recovery. Philz is based off the latest CWM.
https://goo.im/devs/philz_touch/CWM_Advanced_Edition/d2lte/
Place the file in the PDA box, don't check anything except F.reset. Flash the file, once you see reset in the status window, remove USB cable, remove battery, replace battery, boot into recovery.
audit13 said:
I assume you can boot into download mode so use the latest tar version of Philz to flash recovery. Philz is based off the latest CWM.
https://goo.im/devs/philz_touch/CWM_Advanced_Edition/d2lte/
Place the file in the PDA box, don't check anything except F.reset. Flash the file, once you see reset in the status window, remove USB cable, remove battery, replace battery, boot into recovery.
Click to expand...
Click to collapse
I tried this as well.
Sent from my SM-N900T using XDA Premium 4 mobile app
donutkidd said:
I tried this as well.
Sent from my SM-N900T using XDA Premium 4 mobile app
Click to expand...
Click to collapse
You're able to flash and you still don't have the right recovery? What do you see in the recovery screen? Is it the stock recovery?
audit13 said:
You're able to flash and you still don't have the right recovery? What do you see in the recovery screen? Is it the stock recovery?
Click to expand...
Click to collapse
No it's cwm 6.0.3.6, I tried every possible way, I think, of flashing a new recovery but it keeps loading back to this.
Hello Friends,
My phone Galaxy Grand GT-I9082 is stuck on samsung logo; I tried Wipe DATA and Wipe Cache but it is not going ahead ant finally stuck at samsung Logo. for Better View I enclosed snaps.
Need your favour.
Thanks,
Manasvi
Manasvipatel2003 said:
Hello Friends,
My phone Galaxy Grand GT-I9082 is stuck on samsung logo; I tried Wipe DATA and Wipe Cache but it is not going ahead ant finally stuck at samsung Logo. for Better View I enclosed snaps.
Need your favour.
Thanks,
Manasvi
Click to expand...
Click to collapse
Download the latest Official Firmware, preferably for your region. Flash via ODIN.
-PD
Paul_Days said:
Download the latest Official Firmware, preferably for your region. Flash via ODIN.
-PD
Click to expand...
Click to collapse
Hello Paul,
First of all, Thanks for your prompt reply.
I have downloaded the official Firmware and tried it via ODIN-PDA to Auto-Reboot & F. Reset time.
but getting same error as mentioned into Snap.
Thanks,Manasvi
Do you have a Backup of your EFS? im reading the error...that maybe affecting....
Which ROM were you using before ?
Sent from my GT-I9082 using Tapatalk
You need to flash new recovery. Take philz one . flash through Odin or Sideload. Then try formating again through new recovery
akiratoriyama said:
Which ROM were you using before ?
Sent from my GT-I9082 using Tapatalk
Click to expand...
Click to collapse
I have installed official Android version of 4.2.2; I am not technically sound, so not aware about ROM.
Manasvipatel2003 said:
I have installed official Android version of 4.2.2; I am not technically sound, so not aware about ROM.
Click to expand...
Click to collapse
Hello...
Just Follow what K2wl has said...
just install 4.1.2 via odin along with the pit file
follow this http://forum.gsmhosting.com/vbb/f777/samsung-galaxy-grand-i9082-flash-succesfully-1693094/
your partitions are corrupted .
you need to repartition and the re flash the rom through odin.
follow the link given by rutvikrvr.
I have my T-Mobile S4 that I think is useless, however I would like to flash LineageOS to the device. When I turn on the device, it says that the Firmware upgrade encountered an issue. When I load up kies on my PC it doesn't detect my device. When going into boot mode it just says Downloading. Is there any way to fix my device?
Flash the latest stock ROM using Odin.
Getting an error
audit13 said:
Flash the latest stock ROM using Odin.
Click to expand...
Click to collapse
I have the stock ROM, however it keeps failing at around 90% completion.
What is the Odin error? Tried using different usb cables and usb ports?
If the phone was running the latest stock ROM, you could use Odin to flash TWRP and a custom ROM.
Link to Twrp: https://twrp.me/samsung/samsunggalaxys4tmobile.html
https://forum.xda-developers.com/showthread.php?t=2263001
flashing stock rom...
audit13 said:
Flash the latest stock ROM using Odin.
Click to expand...
Click to collapse
Audit13..., how do i flash the rom..? i only have odin and i can't get anything on my internal SD card... What kind of Rom do i need..? A .tar.., can't find one... I have a .zip , 14.1 that i downloaded... Don't know how to get odin to recognize it or how to load it... Everyone keeps wanting to have the rom and gapps already IN the phone on the SD card... Not sure what to do... I can get into download mode on the phone, green man, says downloading... I do get a PSS with TWRP (3.0.2-0) but i can't get it to load once installed... Any help..., anyone..????????
It's a S4 m918...
lentmain said:
Audit13..., how do i flash the rom..? i only have odin and i can't get anything on my internal SD card... What kind of Rom do i need..? A .tar.., can't find one... I have a .zip , 14.1 that i downloaded... Don't know how to get odin to recognize it or how to load it... Everyone keeps wanting to have the rom and gapps already IN the phone on the SD card... Not sure what to do... I can get into download mode on the phone, green man, says downloading... I do get a PSS with TWRP (3.0.2-0) but i can't get it to load once installed... Any help..., anyone..????????
It's a S4 m918...
Click to expand...
Click to collapse
Is your phone bricked?
What exactly are you trying to do?
audit13 said:
Flash the latest stock ROM using Odin.
Click to expand...
Click to collapse
Can you please post the link of the stock ROM and give a detailed guide on how to do flash it because I have the same problem?
Edit: Also please specify the Odin I need to use to flash.
MastetKitty78 said:
Can you please post the link of the stock ROM and give a detailed guide on how to do flash it because I have the same problem?
Edit: Also please specify the Odin I need to use to flash.
Click to expand...
Click to collapse
The latest T-Mobile firmware can be downloaded from here: https://www.sammobile.com/samsung/galaxy-s4/firmware/#SGH-M919
After downloading, unzip the file once using a unzip program such as 7zip.
You will need a Windows PC and Odin: https://odindownloader.com/download/odin3-v3-07
Instructions: https://odindownloader.com/tutorials/use-odin-downloader
It's been a very long time since I have flashed a Samsung s4. There's always a risk that something goes wrong. Best advice: be prepared to try again with different methods if the instructions don't work for your phone.