Hi guys, I´ve bought a DHD, it is my third DHD and the first with troubles. I always did the job using the instructions on htcdev website, but this time it stucks.
The problem? My DHD is a vodafone branded, software number 3.13.161.5 at the htcdev site they dont offer this RUU, only the 3.13.161.3 and of course it won´t work.
In the fastboot menu I got following infos...
ACE PVT SHIP S-ON RL
HBOOT 2.00.0027
RADIO 26.14.52.27
eMMC-boot
does anyone got this appropriate RUU to download so I can do the job, or can it be done on some other way, but please as easy as possible
Thanks
profcb said:
Hi guys, I´ve bought a DHD, it is my third DHD and the first with troubles. I always did the job using the instructions on htcdev website, but this time it stucks.
The problem? My DHD is a vodafone branded, software number 3.13.161.5 at the htcdev site they dont offer this RUU, only the 3.13.161.3 and of course it won´t work.
In the fastboot menu I got following infos...
ACE PVT SHIP S-ON RL
HBOOT 2.00.0027
RADIO 26.14.52.27
eMMC-boot
does anyone got this appropriate RUU to download so I can do the job, or can it be done on some other way, but please as easy as possible
Thanks
Click to expand...
Click to collapse
In htcdev site it says:
"NOTE: If you do not find your ROM version in the table below, and your ROM version is newer, then your device does not require the RUU. Please bypass these steps and continue to the next page."
Because you have newer hboot, just go to next page.
If you whant to get full unlocked bootloader S-off you can use AAHK2 by Phiber2000.
http://forum.xda-developers.com/showthread.php?t=2367322
But it's a little complicated.
Thank you for your reply, but I tried this already, and it wont work. Maybe because my HBOOT is 0027??? I´d rather not to perform a S-off cause I never did it before...
I open the CMD and type fastboot oem_get_identifier_token and the result is : ... INFO(ERR) Command error!!!
I cannot get the token!
profcb said:
Thank you for your reply, but I tried this already, and it wont work. Maybe because my HBOOT is 0027??? I´d rather not to perform a S-off cause I never did it before...
I open the CMD and type fastboot oem_get_identifier_token and the result is : ... INFO(ERR) Command error!!!
I cannot get the token!
Click to expand...
Click to collapse
What do you get when you type: fastboot getvar all
I didn´t type this, untill now...
INFOversion: 0.5
INFOversion-bootloader: 2.00.0027
INFOversion-baseband: 26.14.52.27
INFOversion-cpld: None
INFOversion-microp: 0438
INFOversion-main: 3.13.161.5
INFOserialno: HT11CRX04531
INFOimei: I THINK YOU DON´t NEED THIS
INFOproduct: ace
INFOplatform: HBOOT-7230
INFOmodelid: PD9810000
INFOcidnum: VODAP102
INFObattery-status: good
INFObattery-voltage: 4191mV
INFOpartition-layout: Generic
INFOsecurity: on
INFObuild-mode: SHIP
INFOboot-mode: FASTBOOT
INFOcommitno-bootloader: 743ca94a
INFOhbootpreupdate: 11
INFOgencheckpt: 0
INFOregion-id: 0
all: Done!
finished. total time: 0.026s
Download that UK hboot from HTC dev, start ruu, find in temp rom.zip (or boot.zip, something like that), rename it to PD98IMG.zip, put it on a goldcard, go in hboot and flash it.
Or you can download the whole rom here:
http://shipped-roms.com/index.php?category=android&model=Ace
And the steps are the same.
When you downgrade it with whole ROM just run ruu form htcdev. You don't have to do it with goldcard.
Here is what I did... I download the UK 3.13.161.3 from htcdev found it in temp folder rename it and put it on my sdcard, because I couldn´t find a tutorial how to make a goldcard. Then I went to bootloader and the phone asked me do I want to flash it i choosed yes and the phone restarted. Than I run the RUU but I got the ERROR (191) ROM IS NOT SUPPORTED
EDIT:
I noticed that my bootloader says nov LOCKED so I try again reading the token and I got it, but after pasting the token htcdev gave me following message:
Unlocking Bootloader Failed!
Sorry it didn't work out. Here's why:
Required Resources
Please make sure all items are installed and up to date.
We're sorry, but it appears your attempt to unlock the bootloader on this device has failed. This could be caused by several factors including simple errors in the entry of the unlock token, problems with your device, or a lack of manufacturer support for the unlocking process. Please see the specific error code listed below, and try again if necessary.
Error Code: Invalid Bootloader Token Length.
Error Reason: The submitted Token appears to be the wrong length and won't work.
Click to expand...
Click to collapse
You can install HTC Europe + it's world wide (but it's litle older):
http://shipped-roms.com/download.ph...60.29_26.14.04.28_M_release_225512_signed.exe
Or latest for europe (turkey version):
http://shipped-roms.com/download.ph...60.29_26.14.04.28_M_release_227499_signed.exe
In some thread I was read that even people from US install it.
Yes, whenever you downgradeing rom or hboot or whant to install rom whitch is not for your CID on locked hboot you have to use goldcard.
You get error 191 because you are trying to downgrade on locked hboot.
To make a goldcard:
http://www.addictivetips.com/mobile/how-to-make-gold-card-for-htc-desire-hd/
(4. Go to this page, enter the reverse CID)
Because this page not working here is new one:
http://huygens.hoxnet.com/goldcard.html
Thank you very much, I did it. I just put the ROM.zip found in the temp folder on my sd card, renamed. Then went to bootloader it asked me to whether to flash or not. and than I could get my token...
Related
Hello Experts
Can any one pls help me
I've HTC Desire HD I've flashed it with custom rom after that it stuck on HTC logo
Any solution pls
mdshad1 said:
Hello Experts
Can any one pls help me
I've HTC Desire HD I've flashed it with custom rom after that it stuck on HTC logo
Any solution pls
Click to expand...
Click to collapse
Are you S-OFF and rooted with the Hack Kit or have an unlocked bootloader? What rom did you flash? Have you done a full wipe before flashing?
nearly the same Problem
Hello there, I'm having the same Problem. Stucking at the Splash Logo HTC.
I got this DHD from a friend he means "You got the same one, take a look at it please fix it. ....."
I think he also tried to flash it. But he didnt say or give any thing else.
I was walking around in several Forum but didnt get any kind of results.
But i can give some more information:
I can go to the Bootloader, thats what he said:
ACE PVT SHIP S-ON RL
HBOOT-2.00.0027
MICROP-0438
RADIO-26.14.52.27
eMMC-boot
Sep 7 2011,19:06:24
...
Fastboot
Recovery
Factory Reset
Simlock
Image CRC
---- ----
Image CRC didn't point errors just checksum.
---- -----
fastboot getvar all get this:
INFOversion: 0.5
INFOversion-bootloader: 2.00.0027
INFOversion-baseband: 26.14.52.27
INFOversion-cpld: None
INFOversion-microp: 0438
INFOversion-main: 3.13.161.5
INFOserialno: *******
INFOimei: *******
INFOproduct: ace
INFOplatform: HBOOT-7230
INFOmodelid: PD9810000
INFOcidnum: VODAP102
INFObattery-status: good
INFObattery-voltage: 4040mV
INFOpartition-layout: Generic
INFOsecurity: on
INFObuild-mode: SHIP
INFOboot-mode: FASTBOOT
INFOcommitno-bootloader: 743ca94a
INFOhbootpreupdate: 11
INFOgencheckpt: 0
INFOregion-id: 0
all: Done!
finished. total time: 0.020s
--- ---
It would be very kind if one of you kould get me some help if possible
Thanks!
twomiothandroiduser said:
Hello there, I'm having the same Problem. Stucking at the Splash Logo HTC.
I got this DHD from a friend he means "You got the same one, take a look at it please fix it. ....."
I think he also tried to flash it. But he didnt say or give any thing else.
I was walking around in several Forum but didnt get any kind of results.
But i can give some more information:
I can go to the Bootloader, thats what he said:
ACE PVT SHIP S-ON RL
HBOOT-2.00.0027
MICROP-0438
RADIO-26.14.52.27
eMMC-boot
Sep 7 2011,19:06:24
...
Fastboot
Recovery
Factory Reset
Simlock
Image CRC
---- ----
Image CRC didn't point errors just checksum.
---- -----
fastboot getvar all get this:
INFOversion: 0.5
INFOversion-bootloader: 2.00.0027
INFOversion-baseband: 26.14.52.27
INFOversion-cpld: None
INFOversion-microp: 0438
INFOversion-main: 3.13.161.5
INFOserialno: *******
INFOimei: *******
INFOproduct: ace
INFOplatform: HBOOT-7230
INFOmodelid: PD9810000
INFOcidnum: VODAP102
INFObattery-status: good
INFObattery-voltage: 4040mV
INFOpartition-layout: Generic
INFOsecurity: on
INFObuild-mode: SHIP
INFOboot-mode: FASTBOOT
INFOcommitno-bootloader: 743ca94a
INFOhbootpreupdate: 11
INFOgencheckpt: 0
INFOregion-id: 0
all: Done!
finished. total time: 0.020s
--- ---
It would be very kind if one of you kould get me some help if possible
Thanks!
Click to expand...
Click to collapse
how are you trying to flash a custom ROM without being S-off or having unlocked the bootloader?
Sent from my GT-N7000 using xda app-developers app
glevitan said:
Are you S-OFF and rooted with the Hack Kit or have an unlocked bootloader? What rom did you flash? Have you done a full wipe before flashing?
Click to expand...
Click to collapse
thanx
I've flashed with cygenmod n my phone is rooted n i dont know that it was S-OFF or not
so pls help me fix my problem
glevitan said:
how are you trying to flash a custom ROM without being S-off or having unlocked the bootloader?
Click to expand...
Click to collapse
My friend told me he was performing an Update and after that it didn't come up.
If i try to use the recovery mode it gives an error even if i dont touch any thing (except volup + down + power) E: Can't open /cache/recover/command.
I thought if i could get an update.zip and could update via "Apply update from SDCARD"
twomiothandroiduser said:
My friend told me he was performing an Update and after that it didn't come up.
If i try to use the recovery mode it gives an error even if i dont touch any thing (except volup + down + power) E: Can't open /cache/recover/command.
I thought if i could get an update.zip and could update via "Apply update from SDCARD"
Click to expand...
Click to collapse
bro i've done same process as u told above after doing this method my Desire HD stuck on HTC boot logo
So bro pls tell any solution
mdshad1 said:
thanx
I've flashed with cygenmod n my phone is rooted n i dont know that it was S-OFF or not
so pls help me fix my problem
Click to expand...
Click to collapse
Reboot holding power and volume-down to get to hboot. Look there. Are you S-Off?
twomiothandroiduser said:
My friend told me he was performing an Update and after that it didn't come up.
If i try to use the recovery mode it gives an error even if i dont touch any thing (except volup + down + power) E: Can't open /cache/recover/command.
I thought if i could get an update.zip and could update via "Apply update from SDCARD"
Click to expand...
Click to collapse
What error? Which update file? Is he rooted or S-Off or unlocked?
bananagranola said:
What error? Which update file? Is he rooted or S-Off or unlocked?
Click to expand...
Click to collapse
As i posted above:
ACE PVT SHIP S-ON RL
HBOOT-2.00.0027
MICROP-0438
RADIO-26.14.52.27
eMMC-boot
Sep 7 2011,19:06:24
--> not root not s-off nor unlocked.
The error you quoted:
E: Can't open /cache/recover/command.
This message occured when i enter the recovery menu with (vol down + up + power) after entering hboot
I dont know which update but i thing it has been the official update from Vodafone (service provider) itself. (Android 2.3x ) ?!?
twomiothandroiduser said:
As i posted above:
ACE PVT SHIP S-ON RL
HBOOT-2.00.0027
MICROP-0438
RADIO-26.14.52.27
eMMC-boot
Sep 7 2011,19:06:24
--> not root not s-off nor unlocked.
The error you quoted:
E: Can't open /cache/recover/command.
This message occured when i enter the recovery menu with (vol down + up + power) after entering hboot
I dont know which update but i thing it has been the official update from Vodafone (service provider) itself. (Android 2.3x ) ?!?
Click to expand...
Click to collapse
That is why you are stuck.You are not S-OFF nor Unlocked, so it will be impossible to write partitions in that state. Flash a RUU and that will fix the problem or unlock the bootloader, flash CWM recovery and then a custom rom. That is up to you...
glevitan said:
That is why you are stuck.You are not S-OFF nor Unlocked, so it will be impossible to write partitions in that state. Flash a RUU and that will fix the problem or unlock the bootloader, flash CWM recovery and then a custom rom. That is up to you...
Click to expand...
Click to collapse
Hi, thanks for that,
The question is which RUU.
I found this HOW2 : http://forum.xda-developers.com/showthread.php?t=841890 I need to do whats written there right but they say i need a gold card for RUU flashing?
If that will work would be perfekt!
Thanks for all!
twomiothandroiduser said:
Hi, thanks for that,
The question is which RUU.
I found this HOW2 : http://forum.xda-developers.com/showthread.php?t=841890 I need to do whats written there right but they say i need a gold card for RUU flashing?
If that will work would be perfekt!
Thanks for all!
Click to expand...
Click to collapse
Do not use that, I will guide you on how to do it. You can do the following, create a goldcard and then flash an unbranded RUU for your CID number. The fact is that for creating a goldcard you need a working android device. Do you have another device?
glevitan said:
That is why you are stuck.You are not S-OFF nor Unlocked, so it will be impossible to write partitions in that state. Flash a RUU and that will fix the problem or unlock the bootloader, flash CWM recovery and then a custom rom. That is up to you...
Click to expand...
Click to collapse
Hello Thanks for your messages. I searched severals RUUs but none of them worked, it says Imageversion 3.13.161.5 and Error [132]: signature error
Any Idea?
edit:
I also tried loading the rom.zip into the SD card naming it as pd98img.zip. The phone recognized it checks it but than returns back to the fastboot menu!
twomiothandroiduser said:
Hello Thanks for your messages. I searched severals RUUs but none of them worked, it says Imageversion 3.13.161.5 and Error [132]: signature error
Any Idea?
edit:
I also tried loading the rom.zip into the SD card naming it as pd98img.zip. The phone recognized it checks it but than returns back to the fastboot menu!
Click to expand...
Click to collapse
That is because that RUU's seems not be for your device. Even flashing them as PD98IMG won't work if those RUUs do not match your CID. If you have another android working device I can help you create a goldcard, if not I guess the best is to unlock bootloader and then get a custom rom...
If it is alright with you I can help you over teamviewer...
glevitan said:
That is because that RUU's seems not be for your device. Even flashing them as PD98IMG won't work if those RUUs do not match your CID. If you have another android working device I can help you create a goldcard, if not I guess the best is to unlock bootloader and then get a custom rom...
If it is alright with you I can help you over teamviewer...
Click to expand...
Click to collapse
You wont believe i have a second one
it has s-off
it would be kind if you show me both ways.
twomiothandroiduser said:
You wont believe i have a second one
it has s-off
it would be kind if you show me both ways.
Click to expand...
Click to collapse
Use this to create the goldcard...be cautious on how you do that to avoid corrupting the sdcard:
http://forum.xda-developers.com/showthread.php?t=970157
Once you have patched the sdcard, without dismounting it, put a RUU in there and name it PD98IMG.zip, then boot in bootloader and wait until you are prompted to update.
And if you are a bit lost, download this: http://www.teamviewer.com and I can connect to your PC to lend you a hand.
glevitan said:
Use this to create the goldcard...be cautious on how you do that to avoid corrupting the sdcard:
http://forum.xda-developers.com/showthread.php?t=970157
Once you have patched the sdcard, without dismounting it, put a RUU in there and name it PD98IMG.zip, then boot in bootloader and wait until you are prompted to update.
And if you are a bit lost, download this: http://www.teamviewer.com and I can connect to your PC to lend you a hand.
Click to expand...
Click to collapse
Hi, i tried what you told me to do. with the The programm crashed at point 5 so i used this german side http://www.pocketpc.ch/htc-desire-hd-root-rom/111867-anleitung-desire-hd-goldcard-erstellen.html to create an gold card. but the wired thing is, that the http://psas.revskills.de/?q=goldcard wants to get the cid not the reversed cid.
But all in all after I created that gold card with hex editor, and putting the ruu as pd98img.zip on the SD. The bootloader was loading the *.zip and checking the zip and without error or anything else it just got back to the bootloader.
Hello bro i've flashed my hTc desire HD without knowing that it is S-OFF or not directly using Power+Volume down then selected the recovery and then Volume up+power and after that apply from sd card
Now my phone is stuck on hTc logo
So plz help me to fix my promblem
mdshad1 said:
Hello bro i've flashed my hTc desire HD without knowing that it is S-OFF or not directly using Power+Volume down then selected the recovery and then Volume up+power and after that apply from sd card
Now my phone is stuck on hTc logo
So plz help me to fix my promblem
Click to expand...
Click to collapse
If you are S-OFF, put a custom rom in the sdcard, boot in recovery and flash it. That will sort it out.
glevitan said:
Use this to create the goldcard...be cautious on how you do that to avoid corrupting the sdcard:
http://forum.xda-developers.com/showthread.php?t=970157
Once you have patched the sdcard, without dismounting it, put a RUU in there and name it PD98IMG.zip, then boot in bootloader and wait until you are prompted to update.
And if you are a bit lost, download this: http://www.teamviewer.com and I can connect to your PC to lend you a hand.
Click to expand...
Click to collapse
I'm sad. I tried it at a nother PC it creates the Goldcard (it said it has) I copied the RUU. Put SD into the phone Restart the Phone into the boot loader. Waited the file to check . and then. Back to the hboot menu nothing more.
Hi everyone!
I've managed to screw up my Desire HD after running aahk-11092012, and was wondering if anyone had any bright ideas...
The Phone is a Desire HD bought from SFR here in France in 2011, never rooted or custom rom'ed, although updated with 2or 3 SFR roms since.
I ran aahk from the terminal on a OSX 10.7 (see Output.txt). From this you will see that it wants naturally to downgrade (to Froyo I assume) but downloading the rom fails, and even though I refused the "-n Flash this RUU? (y/n)" question, it continued doing all sorts of things, getting a few error along the way, rebooting the phone into recovery a few times, and finishes with
************* Downgrade failed *************
** Either:
** GoldCtixiard/SDCard failed
** USB connections are not working 100%
************* Downgrade failed *************
I then tried to flash the "Gingerbread HTC WWE 2.50.405.2" rom from the options menu, thinking I'd be clever, but that monumentally fails too..
From this point on the phone boots to the "Red tringle with an exclamation mark" screen (after the white HTC logo) and does nothing else.
Restarting AAHK just fails with a "Error detecting HTC phone on USB connection."
Having discovered the "VOL-UP +Power" recovery screen during this process, the next thing I tried was a "Apply sdcard:update.zip", but this just results in an "Invalid command" message underneath that already present "E: Can't open /cache/recovery/command" in yellow further down the screen.
I then try a "Wipe data/factory reset" and also a "Wipe cache partition". I can't honestly explain this. At least not given that I hadn't really looked up the issue anywhere yet. I also cant remember exactly what the output was, but the result is the same, still the red triangle screen.
OK, so now I finally open my eyes and realize what a moron I've been, so i plunge into actually learning something and realize quickly (aside from I hate myself and I'm not special, bla bla) that there are loads of thing I could have done differently, and directly on the phone, but obviously it's now too late. (See below for the information I CAN get from the Phone)
Oh yes, I did try a "Factory reset" from HBOOT, but still no joy....
The main option I've been looking into has been to recover an original branded SFR firmware and Froyo ROM and go from there, so I did manage to get a PD98IMG.zip file onto the SD card and HBOOT recognizes it, but fails with a "CID Incorrect" error.
I seem, therefore to be stuck whether I want to return to original SFR or continue tryng to flash a custom ROM:
I can't make a goldcard: I cant adb any commands, in HBOOT the device is not found, and in recovery the device is found but is "offline".
I found jo0ls' CID reader, but I dont have a SD card reader directly plugged to the PCI bus!
I did finally try to install a clockwork recovery in FASTBOOT, but get this:
$ fastboot flash recovery recovery-clockwork-5.0.2.0-ace.img
sending 'recovery' (3624 KB)... OKAY
writing 'recovery'... INFOsignature checking...
FAILED (remote: signature verify fail)
I assume this is much the same error as for the PD98IMG...
Sorry about the long winded post, but I hope it has the maximum of info...
Anyone have any ideas?
- I can boot to HBOOT: it shows me this:
ACE PVT SHIP S-ON RL
HBOOT-2.00.0027
MICROP-0438
RADIO-26.03.02.26_M
eMMC-boot
Sep 7 2011, 19:06:24
- ...and FASTBOOT, fastboot getvar all gives this:
INFOversion: 0.5
INFOversion-bootloader: 2.00.0027
INFOversion-baseband: 26.03.02.26_M
INFOversion-cpld: None
INFOversion-microp: 0438
INFOversion-main: 1.32.405.6
INFOserialno: SH12GRX00567
INFOimei: 356812048021701
INFOproduct: ace
INFOplatform: HBOOT-7230
INFOmodelid: PD9810000
INFOcidnum: VODAP203
INFObattery-status: good
INFObattery-voltage: 4199mV
INFOpartition-layout: Generic
INFOsecurity: on
INFObuild-mode: SHIP
INFOboot-mode: FASTBOOT
INFOcommitno-bootloader: 743ca94a
INFOhbootpreupdate: 11
INFOgencheckpt: 0
INFOregion-id: 0
all: Done!
- The recovery is the original "Android system recovery <3e>"
AAHK, and the server hosting the downgrade files, is retired. You can still unlock the bootloader, but your hboot needs updating before it cam be unlocked. I think you could also run your stock RUU.
CID Number shows that your device is a Vodafone device, probably VodaSFR but who knows? Fetch a Voda RUU and install it
Sent from my Desire HD using Tapatalk 2
you need to upgrade your bootloader to 2.00.0029
htcdev.com/ruu/PD9810000_Ace_Sense30_S_hboot_2.00.0029.exe (sorry, i can´t atach links)
then unlock it(follow htc-dev guide) and you will be able of flashing a custom recovery
pascuals said:
you need to upgrade your bootloader to 2.00.0029
htcdev.com/ruu/PD9810000_Ace_Sense30_S_hboot_2.00.0029.exe (sorry, i can´t atach links)
then unlock it(follow htc-dev guide) and you will be able of flashing a custom recovery
Click to expand...
Click to collapse
Thanks for all your answers!
@ bananagranola: I did know aahk had been discontinued, I actually mentioned this originally but edited it out to "shorten my post"!
@ humzaahmed155: quite right, I'm with SFR, and I'm trying to simply restore an original branded ROM
@ pascuals: I will look into your suggestion right away! I was vaguely aware I might have to do this but could not get an accurate enough idea of what version might be appropriate for my phone
[SOLVED] [Q] Desire HD can't boot (red triangle) after AAHK Fail
Kawika1611 said:
Thanks for all your answers!
@ bananagranola: I did know aahk had been discontinued, I actually mentioned this originally but edited it out to "shorten my post"!
@ humzaahmed155: quite right, I'm with SFR, and I'm trying to simply restore an original branded ROM
@ pascuals: I will look into your suggestion right away! I was vaguely aware I might have to do this but could not get an accurate enough idea of what version might be appropriate for my phone
Click to expand...
Click to collapse
Woohoo!! I'm so happy, I got the phone working again last night!! I had a ruu kicking around:
RUU_Ace_Sense30_S_Vodafone_FR_3.13.163.3_Radio_12.65.60.29_26.14.04.28_M_release_227340_signed.exe
from the first day I'd bricked it. This hadn't worked the first time I tried it on windows (actually a Parallels VM on Mac), with the phone plugged in, but I can't remember what mode the phone was in; but as you'll see below I must not have been in fastboot...
Whatever, last night I finally tried pascuals's PD9810000 RUU, with the phone connected and in fastboot, the utility detects the phone fine, but fails with a firmware version error, saying the phone is 1.32.405.6, it will install version 3.13.0.0 but I need to "upgrade to 3.12.405.1"..:silly: (see attachments).
Feeling dejected I fired up the rom cited above thinking I have nothing to lose, and...lo an behold...10 minutes or so later the phone reboots to a beautiful welcome screen insulting me for not having inserted a SIM card!!!
Thanks anyway for your answers, at least they got me looking in the right direction!! I will now go a learn properly how this things work before bricking it again
pascuals said:
you need to upgrade your bootloader to 2.00.0029
htcdev.com/ruu/PD9810000_Ace_Sense30_S_hboot_2.00.0029.exe (sorry, i can´t atach links)
then unlock it(follow htc-dev guide) and you will be able of flashing a custom recovery
Click to expand...
Click to collapse
My HBOOT is 0.85.2425, after S-OFF. Can I update to 2.00.0029? How?
Thanks.
use that link and just run the exe with your phone connected, atleast with debugging on i think, mine was like that, the tool took care of the rest automatically.
mobidor said:
My HBOOT is 0.85.2425, after S-OFF. Can I update to 2.00.0029? How?
Thanks.
Click to expand...
Click to collapse
I see no reason why you need to update the bootloader when you already have s-off. If your bootloader is engineering bootloader then just let it be.
Sent from my Desire HD
Hello everybody,
I tried to install jellytime on my Desire HD, so i used Easy Ace Root Tool.
I used fastboot command to flash the boot.img to the phone and since then, the only menu available is the one of the bootloader.
As far as i tried the ruu packages fail to restore things.
Is there a way (preferably a guide) to return my phone to stock ?
Loading to fastboot now shows:
*** relocked ***
ACE PVT SHIP S-ON RL
HBOOT-2.00.0029
MICROP-0438
RADIO-26.14.04.28_M
eMMC-boot
Dec 22 2011, 14:28:19
Thanks!
gavanas said:
Hello everybody,
I tried to install jellytime on my Desire HD, so i used Easy Ace Root Tool.
I used fastboot command to flash the boot.img to the phone and since then, the only menu available is the one of the bootloader.
As far as i tried the ruu packages fail to restore things.
Is there a way (preferably a guide) to return my phone to stock ?
Loading to fastboot now shows:
*** relocked ***
ACE PVT SHIP S-ON RL
HBOOT-2.00.0029
MICROP-0438
RADIO-26.14.04.28_M
eMMC-boot
Dec 22 2011, 14:28:19
Thanks!
Click to expand...
Click to collapse
fastboot getvar all
and post the results.
nlooooo said:
fastboot getvar all
and post the results.
Click to expand...
Click to collapse
C:\Users\George Gavanas>fastboot getvar
INFOversion: 0.5
INFOversion-bootloader: 2.00.0029
INFOversion-baseband: 26.14.04.28_M
INFOversion-cpld: None
INFOversion-microp: 0438
INFOversion-main: 3.13.0.0
INFOserialno: SH15ZRX00171
INFOimei: ???
INFOproduct: ace
INFOplatform: HBOOT-7230
INFOmodelid: PD9810000
INFOcidnum: HTC__001
INFObattery-status: good
INFObattery-voltage: 4035mV
INFOpartition-layout: Generic
INFOsecurity: on
INFObuild-mode: SHIP
INFOboot-mode: FASTBOOT
INFOcommitno-bootloader: fcef1579
INFOhbootpreupdate: 11
INFOgencheckpt: 0
INFOregion-id: 0
all: Done!
finished. total time: 0.010s
gavanas said:
C:\Users\George Gavanas>fastboot getvar
INFOversion: 0.5
INFOversion-bootloader: 2.00.0029
INFOversion-baseband: 26.14.04.28_M
INFOversion-cpld: None
INFOversion-microp: 0438
INFOversion-main: 3.13.0.0
INFOserialno: *************************
INFOimei: **********************
INFOproduct: ace
INFOplatform: HBOOT-7230
INFOmodelid: PD9810000
INFOcidnum: HTC__001
INFObattery-status: good
INFObattery-voltage: 4035mV
INFOpartition-layout: Generic
INFOsecurity: on
INFObuild-mode: SHIP
INFOboot-mode: FASTBOOT
INFOcommitno-bootloader: fcef1579
INFOhbootpreupdate: 11
INFOgencheckpt: 0
INFOregion-id: 0
all: Done!
finished. total time: 0.010s
Click to expand...
Click to collapse
Go here
http://www.shipped-roms.com/index.php?category=android&model=Ace
download thi RUU
RUU_Ace_Sense30_S_HTC_WWE_3.12.405.1_Radio_12.65.60.29_26.14.04.28_M_release_225512_signed.exe
And try to run it with phone in fastboot.
If that doesn't work try with some RUU that has 3.13.xxx.x main version (i.e. RUU_Ace_Sense30_S_hTC_Asia_WWE_3.13.707.4_R_Radio_12.65.60.29_26.14.04.28_M_release_234022_signed.exe)
both result in error...
The second says ID error
is there any way i can restore the original firmware? maybe put it in the sd card?
gavanas said:
both result in error...
The second says ID error
is there any way i can restore the original firmware? maybe put it in the sd card?
Click to expand...
Click to collapse
I found the rom.zip from the second file, renamed it to PD98IMG.zip and inserted it to my sd, but it say CID error.
I saw that everyone says about a goldcard but i don't seem to get it. The goldcard generator i downloaded say they could not locate the CID. Can i download a CID image?
Where should i put it, if i find one?
Thanks!
gavanas said:
I found the rom.zip from the second file, renamed it to PD98IMG.zip and inserted it to my sd, but it say CID error.
I saw that everyone says about a goldcard but i don't seem to get it. The goldcard generator i downloaded say they could not locate the CID. Can i download a CID image?
Where should i put it, if i find one?
Thanks!
Click to expand...
Click to collapse
I have tried many different ruu's and always get an error.
When i flash with PD98IMG i get a cid error
Is there any way out?
Even with a custom rom (jellytime)
Please help!!!:crying:
Use AAHK2
gavanas said:
I have tried many different ruu's and always get an error.
When i flash with PD98IMG i get a cid error
Is there any way out?
Even with a custom rom (jellytime)
Please help!!!:crying:
Click to expand...
Click to collapse
Try the AAHK2 Script. Make sure you follow all the instructions before using the script.. It will automatically do things for you and just follow the on screen instructions... At the end you will have your Stock Rom perfectly running... :good:
Delete your imei #
Get nloooo to delete it from the quote as well.
Sent from a dream.
gkprashu said:
Try the AAHK2 Script. Make sure you follow all the instructions before using the script.. It will automatically do things for you and just follow the on screen instructions... At the end you will have your Stock Rom perfectly running... :good:
Click to expand...
Click to collapse
I used AAHK2 when my phone got into a similar situation. It worked like charm
gavanas said:
I have tried many different ruu's and always get an error.
When i flash with PD98IMG i get a cid error
Is there any way out?
Even with a custom rom (jellytime)
Please help!!!:crying:
Click to expand...
Click to collapse
Do not use the AAHK2 if you are trying to return to stock for warranty purposes, thou I highly doubt that you still have warranty on this device .
In order to bypass the CID error you need to use a goldcard. Otherwise, you will need the exact ruu for your device.
glevitan said:
Do not use the AAHK2 if you are trying to return to stock for warranty purposes, thou I highly doubt that you still have warranty on this device .
In order to bypass the CID error you need to use a goldcard. Otherwise, you will need the exact ruu for your device.
Click to expand...
Click to collapse
After trying the 4.3 beta versions, i tried again to install the original firmware.
As before, the ruu setup did not work. It should, since my cid is HTC__001, and i was trying with every WWE version available.
Anyway, during setup, i found in the temp folder the rom.zip, and within it the necessary boot.img, system.img and recovery.img.
I flashed them through cmd using fastboot.
Everything worked out, now i am back to stock, but i guess that my phone is something like Frankenstein, using the radio and libraries from the last jellytime image i installed...
It works, but i don't recommend it. I think that i finally got lucky, and didn't brick my Desire HD.
Thanks for all your help and interest.
glevitan said:
Do not use the AAHK2 if you are trying to return to stock for warranty purposes, thou I highly doubt that you still have warranty on this device .
In order to bypass the CID error you need to use a goldcard. Otherwise, you will need the exact ruu for your device.
Click to expand...
Click to collapse
That is weird as ruu's flash all partitions.
Sent from my ASUS Transformer Pad TF700T using xda app-developers app
glevitan said:
That is weird as ruu's flash all partitions.
Sent from my ASUS Transformer Pad TF700T using xda app-developers app
Click to expand...
Click to collapse
i think you misunderstood him mate, he flashrd only specific img files from ruu not the whole thing. in this case, radio doesnt get flashed, but that shouldnt be to big of a problem.
to op: custom roms dont contain radios. so radio that is on your device is the same as before you flashed jellytime
t0mas_ said:
i think you misunderstood him mate, he flashrd only specific img files from ruu not the whole thing. in this case, radio doesnt get flashed, but that shouldnt be to big of a problem.
to op: custom roms dont contain radios. so radio that is on your device is the same as before you flashed jellytime
Click to expand...
Click to collapse
Well, RILs are not compatible then, and many AOSP partitions can not work fine with Sense Roms. If he did that then his cell might explode....
forgot about rils and didnt know about partitions.
but expoding cells are not to be taken lightly, especially when put in trouser pocket
Hi I have a htc one v on 3 (H3G__001) it is on hboot 1.18.0000 radio 3831.19.00.120
I cant seem to find a ruu file for it even on androidfileshost.
all other ruu files fail at one point or another usually due ro wrong CID or older HBOOT
I have tried running a ruu with the correct hboot then when it got to the confirmation page i types %.temp% and found where the temp
install files were and i opened the rom.zip and edited the android-info.txt file adding H3G__001 to the file saving it and rezipping it then
continuing with the RUU installation.
Im hoping someone can help me recover the phone as im stuck in how to get it back working.
It is my fault as I locked the bootloader when returning to stock BEFORE I flashed the recovery and hboot (I know im an idiot) and htcdev wont unlock my relocked bootloader it just freezes then eventually gives me the "too many links" error message
here is the info I got from typing fastboot getvar all
C:\adb>fastboot getvar all
INFOversion: 0.5
INFOversion-bootloader: 1.18.0000
INFOversion-baseband: 3831.19.00.120
INFOversion-cpld: None
INFOversion-microp: None
INFOversion-main:
INFOserialno: HT24JTV02137
INFOimei: 351816054460252
INFOproduct: primou
INFOplatform: HBOOT-7230
INFOmodelid: PK7610000
INFOcidnum: H3G__001
INFObattery-status: good
INFObattery-voltage: 3954mV
INFOpartition-layout: Generic
INFOsecurity: on
INFObuild-mode: SHIP
INFOboot-mode: FASTBOOT
INFOcommitno-bootloader: 8591a55c
INFOhbootpreupdate: 12
INFOgencheckpt: 0
all: Done!
Thank you for reading and I hope you can help.
micky3936 said:
Hi I have a htc one v on 3 (H3G__001) it is on hboot 1.18.0000 radio 3831.19.00.120
I cant seem to find a ruu file for it even on androidfileshost.
all other ruu files fail at one point or another usually due ro wrong CID or older HBOOT
I have tried running a ruu with the correct hboot then when it got to the confirmation page i types %.temp% and found where the temp
install files were and i opened the rom.zip and edited the android-info.txt file adding H3G__001 to the file saving it and rezipping it then
continuing with the RUU installation.
Im hoping someone can help me recover the phone as im stuck in how to get it back working.
It is my fault as I locked the bootloader when returning to stock BEFORE I flashed the recovery and hboot (I know im an idiot) and htcdev wont unlock my relocked bootloader it just freezes then eventually gives me the "too many links" error message
Thank you for reading and I hope you can help.
Click to expand...
Click to collapse
Not even here: http://androidruu.com/?developer=Primo
And, are you primou or primoc?
No sadly its not on there as only for older hboots for my phone. there is 1.18.000 hboots on there but not to match my cid.
Im on primou with 3 uk which is H3G__001
Hey guys I want to unroot my old desire, I have managed to put original ruu on but my hboot still says revolutionary and my hboot is 6.93 I tried downlaoding and running android flasher but it failed when writing the hboot that came with it. Does anyone know how to do it so I can have it locked with s-on?
I don't believe I have stock hboot and can't find a good link to one either.
Thanks
Use bortak's troubleshooting guide, stickied to the top of q&a
Point number [8]
eddiehk6 said:
Use bortak's troubleshooting guide, stickied to the top of q&a
Point number [8]
Click to expand...
Click to collapse
So if I follow this:
Visit Alpharev and download the "Downgrader"
[STEP2]- Flash the downgrader over fastboot. This can be done with Android Flasher, cmd, or fastboot commander (Note: android flasher is the
only program that does not require third party software such as Android SDK or Java JDK)
[STEP3]- You should now notice the title on the bootloader screen is "Alpharev Unlock", run the RUU again and you will have S-ON'd your device.
Am I right in saying it will change to s-on but it will also get rid of revolutionary at the top of the screen? Can I change that to locked after by using fastboot oem lock?
si_d_2003 said:
Am I right in saying it will change to s-on but it will also get rid of revolutionary at the top of the screen?
Click to expand...
Click to collapse
Yes
Can I change that to locked after by using fastboot oem lock?
Click to expand...
Click to collapse
No need
eddiehk6 said:
Yes
No need
Click to expand...
Click to collapse
I tried to run the ruu : RUU_Bravo_H3G_UK_1.22.771.1_Radio_32.36.00.28U_4.06.00.02_2_release_127568_signed and I get a HBoot version error and it exits the exe.
Is there any advice you could give me please?
This is my info:
c:\fastboot>fastboot getvar all
INFOversion: 0.5
INFOversion-bootloader: 0.93.0001
INFOversion-baseband: 5.09.05.30_2
INFOversion-cpld: None
INFOversion-microp: 051d
INFOversion-main: 2.10.405.2
INFOserialno:
INFOimei:
INFOproduct: bravo
INFOplatform: HBOOT-8x50
INFOmodelid: PB9920000
INFOcidnum: H3G__001
INFObattery-status: good
INFObattery-voltage: 4187mV
INFOpartition-layout: Generic
INFOsecurity: on
INFObuild-mode: SHIP
INFOboot-mode: FASTBOOT
INFOcommitno-bootloader: dirty-365c78d6
INFOhbootpreupdate: 11
all: Done!
finished. total time: 0.030s
si_d_2003 said:
1.22.771.1
Click to expand...
Click to collapse
si_d_2003 said:
INFOversion-main: 2.10.405.2
Click to expand...
Click to collapse
Ur version main is 2.10.405.2 the ruu ur trying is version 1.22.771.1 so u have to use a ruu with version main 2.10.405.2 or higher
In addition to the above, find and use the 2.3.3 GB RUU from shippedroms
If it fails to flash normally, flash it using the PB99IMG.zip method, point [7] from the same guide