Loose power button - No Warranty - AT&T, Rogers, Bell, Telus Samsung Galaxy S III

If I were to attempt to fix this issue myself, how would I go about doing it? I ordered a new power button but I'm worried that the problem lies internally requiring me to take apart the phone rather than just replacing a simple button. The power button is so loose that if you make any contact on it, it will turn on/off. If I press it down, it makes a click sound as usual but the screen flickers on and off.

karmasblade said:
If I were to attempt to fix this issue myself, how would I go about doing it? I ordered a new power button but I'm worried that the problem lies internally requiring me to take apart the phone rather than just replacing a simple button. The power button is so loose that if you make any contact on it, it will turn on/off. If I press it down, it makes a click sound as usual but the screen flickers on and off.
Click to expand...
Click to collapse
Replacing the power button requires opening up the phone. Unless you are certain you have the correct tools and technical expertise for this, you may want to consider taking it to a tech shop or pro outlet. This may cost you a bit but could be overall less bothersome.

Related

is this a common problem?

my xda2s recently experienced a problem which consists of the volume bar keep going up and up making the 'end' noise repeatedly, and if say the volume bar on the side were to be pressed down, it would go down n go up again...
secondly, the power button is not functioning well, it can turn the phone on by clicking it once (as usual) it can turn the backlight on and off by holding it (as usual) but it wont turn off by pressing it once, or anything...
help please, thank you
doesn't happen with any of my 3... sounds like you've got them there problems.
pYroboy,
let me know if you found the resolution. My problems are similar to yours...
Thanks.
doesnt happen to any of my two BA...
try opening up your unit and clean up the contacts.
I did open it, but could not figure out which contact to clean. Power switch is sooooooo freaking small, I did not figure out what I could clean there, it seems that it is 2x4mm in size soldered for good to the board. Same about volume rocker/switch on the side.
How is it possible to clean them??? I could not figure out what could be cleaned there without detaching the switches from the board.
Does anyone sell these parts? Maybe it would be easier (although not easy also because they are so freaking small) to replace them??
Guys, need advice from you... from the ones who fooled around with similar parts...
Thanks.
try an air brush. or a fast evaporating contact cleaner.
just make sure you apply enough pressure not to blow the sensitive parts away.
*just becareful
OK. Thanks. I'll try that. But where do you people get that stuff. Do they sell it in electronics stores, or I need to look someplace else?
I need to do something anyway, because today I can't turn ON. I used timeout of 1 minute on battery power to power it OFF. But not being able to turn the whole thing ON really put me down....
Is there any program to remap Power On/Off button to Recorder or Media Player buttons on the side? They are all 3 the same switches. If it would be possible, I'd get by using one of those buttons.... Just running out of freaking ideas here....
contact cleaners can be found in your local radioshack(i.e. electronics or computer botique/shops).
regarding the power button i think that is hardwired to be the only powerbutton for the unit. sad to say you cant map it to powerup your BA.
pecq said:
OK. Thanks. I'll try that. But where do you people get that stuff. Do they sell it in electronics stores, or I need to look someplace else?
I need to do something anyway, because today I can't turn ON. I used timeout of 1 minute on battery power to power it OFF. But not being able to turn the whole thing ON really put me down....
Is there any program to remap Power On/Off button to Recorder or Media Player buttons on the side? They are all 3 the same switches. If it would be possible, I'd get by using one of those buttons.... Just running out of freaking ideas here....
Click to expand...
Click to collapse
Assuming you have the button lock enabled you can wake it up by receiving a phone call, and then disable the button lock and use any button to wake up/turn on the device. This is not the most elegant solution, but if cleaning fails to fix it then it may be your only option.

Double tap screen to wake device up?

Would it be possible to configure our Rhodiums to wake from sleep mode upon a quick double tap on the screen? If possible it could be set that only a double tap (one tap followed by another no longer than half a second later for example) would wake the device to ensure accidental knocks in our pocket wouldn't wake it.
Any ideas?
Thanks
anyone any ideas?
I'm going to go out on a limb and say this isn't possible without seriously jeapordizing battery life, so it wouldn't be something plausible.
Consider that what you're asking means your device will always have to monitor the screen and thus never enter standby mode.
Perhaps you should look into applying the registry fix that will wake your device on any key press (not just the power button). Maybe that will work for you as well, while still letting your device go into standby.
What is wrong with the built-in power button again?
I would like that also (different button to turn on). With the diamond the centre round button would be a better button to turn on the pda than the current power button (which is a little too far recessed for my liking) The centre button is larger but recessed also which would stop accidently turning in on in your pocket.
Link to previous thread regarding pressing any key to wake...
ohyeahar said:
I'm going to go out on a limb and say this isn't possible without seriously jeapordizing battery life, so it wouldn't be something plausible.
Consider that what you're asking means your device will always have to monitor the screen and thus never enter standby mode.
Perhaps you should look into applying the registry fix that will wake your device on any key press (not just the power button). Maybe that will work for you as well, while still letting your device go into standby.
Click to expand...
Click to collapse
yeah thats a fair point, ddn't think too much about the implications of it having to perhaps always be awake!
Spike15 said:
What is wrong with the built-in power button again?
Click to expand...
Click to collapse
Nothing wrong with the power button, just thought itd be a cool feature to be able to do that, but ill stick with whats best!
I think HTC's placement of the power button is perfect. I've been using smartphones and PDAs for a while and that's just the natural spot I EXPECT a power button to be. In fact with my breif stay with a Blackjack II I kept hitting the power button to dim the screen, which on that phone would actually turn it off, like off off.
And as stated above, when your phone goes into standby, the screen turns off, it can't detect anything. In order to keep the sensor on, you would be draining power when your phone really shouldn't.
I'll throw my coin in the hat of "silly idea"
My first Tilt 2, which had a dud microphone, the power button was fine.. It was recessed but easily pressed. My current Tilt 2 I have to press holding the phone longwise.. if I'm holding the phone on the sides I can't press the power button... I'm thinking the screen moves slightly more or the button is more recessed. It's kind of annoying.
Personally I'd also like not have to use the power button all the time myself, although I wouldn't want to tap to do it.. One of the four hardware buttons would be just fine.
Yes, I know sliding and removing the stlyus turn it on too, neither thing I do often.

Fast click on power on

Hello,
I saw that the phone is switched off when I press the power button very quickly after a few seconds turns on. This for me is very annoying, if I have the phone in my pocket sometimes turns on probably because Touch inside the power button. It is possible to change to having to press for a few seconds and not for 1/10 second ?
it is not possible ?
alfredolo said:
it is not possible ?
Click to expand...
Click to collapse
Why is this a problem? The screen will auto switch off again in 15 seconds if still locked.
Becouse i want turn off the phone.
You want it totally switched off? Hold down the power button and a menu pops up on the screen, switch if off from there.
There is no way to stop the power button waking up the device when it is "standby", that's its purpose, I can't imagine anything more annoying than having to hold down the button just to check my phone
I don't see how you guys don't understand his question.
He says that it is annoying that when you turn the phone off (for X reason) and put it in your pocket, the fact that it only takes a slight touch of the power button to turn the phone on means it involuntarily turns itself on in his pocket. He wantsto know whether it is possible to make it so you have to press a long time on the power button in order to turn the power on, so that if the power buton is only pressed for a second, nothing happens.
I really wish people tried to actually read questions on forums.
This is an important question for all that travel by air.
to avoid that during the take off or the landing the desire turn on inadvertently
My problem was born in the cinema when I turned off the phone and put it in my pocket. After a few seconds I heard the sound of ignition, so I switched off again, then yet again ... up when I removed the sound, while other people looked at me in a mole ..
It would be nice if you could choose to press the button for 2-3 seconds before it turn on, to prevent accidental starting
Totally agree. I had the same issue on the plane the other day. I had powered it off but during take off it powered itself on in my pocket. I used to have an iPhone and it at least required you to hold the power button down for a few seconds before it turned on.
-------------------------------------
Sent via the XDA Tapatalk App
speedking34 said:
I really wish people tried to actually read questions on forums.
Click to expand...
Click to collapse
I really wish people took the time to actually read the reply and accept that sometimes when the OP is in broken english it is misses details, before jumping in to criticise others while contributing nothing of value to the thread.
If you reckoned it was easy to understand the question, why have you offered no actual answer or constructive advice?
If you assume that the question is... can I set the phone so that it requires a long-press of the power button to switch it on when it is completely powered off... the answer is... No, you can't. Perhaps there is scope for this in a modded firmware if you root the device. I suggest you email HTC support to suggest this an an enhancement in a future update to the phone.
Why don't you try this FlexiSheild Case Cover, I purchased one and it has a very robust construction flexible but not sloppy like the silicone ones.
I have found that to turn the phone on or from standby you have firmly press the on button you cannot turn it on by simply sweeping your finger over the button it also offers a lot of protection to the phone and has some rubbery coating on the back to stop the phone slipping out of your hand.
I believe this will elimenate your false switch on of the phone
http://www.mobilefun.co.uk/flexishield-skin-for-the-htc-desire-black-p24206.htm

[Ghetto Fix] for broken power button issue (t989)

Symptoms:
Extreme Case: Once phone is plugged in or battery inserted, phone vibrates constantly and never progresses further through the boot cycle.
Moderate Case: Phone is able to make it to Samsung logo, or sometimes even further, but never fails to reboot and remain stuck in this cycle.
Preliminary Case: Phone randomly reboots for no reason, or when power button is gently touched (not hard pressed)
Problem:
1) Either phone button is sticky for some reason (ewww) and gets stuck, causing phone to reboot.
2) Or, (more severe cases) the internal switch is beginning to malfunction (common) and needs to be replaced in order to really fix the problem.
Fixes:
1) If the button is sticky, simply clean it you sicko and quit being dirty. Plenty of guides on how to open the phone on Youtube. (This is not really a big issue though)
2) Faulty hardware is going to require some major work to be completely fixed.
Ghetto Fix:
Intro: My phone is showing preliminary issues of the common switch malfunction issue. I read around and it seems that Samsung just failed with that portion of the hardware. My brother's phone, on the other hand, was an extreme case and was basically a brick in my room for a few months until I decided to fix it. It's not a profound fix, so I'm sorry for those who really want this issue solved. If you do, I recommend either replacing the part yourself or taking it to a shop to repair it for you. This fix is for those of you who might have an fully functioning galaxy s2 laying around, with the exception of that stupid button.
1) You will need to know how to open up your phone. There are many guides on Youtube. Be very careful doing so.
2) Ghetto Button Fix (Two Options) *From here on I will have to make a distinction between the two senses of "power button" I am talking about: There is the power button on the logic board (LB Power Button [my term]) and the one on the outside of the phone---the (P Power Button [my term]) is the one you see and press when your phone is put together and working fine--the (LB Power Button) is the switch attached to the logic board
a. The first ghetto fix will work if your case is not too severe, and it will look less ghetto. When you open your phone and separate all the parts, you are left with a good view of the (P Power Button)--you will notice that a small rubbery rectangular portion of the power button--file that off completely to prevent the (P Power Button) from touching the logic board power button (LB Power Button).
*Note: This will not be a fix for more extreme cases because the (P Power Button) can still reach the (LB Power Button). This will only make it less likely for the two to make contact when you do not want it to. Also note that the issue is not with the two making contact, it is a faulty switch. Anything from a quick jolt or vibration, or even gravity can be enough to set it into a looped cycle.
b. If the first one doesn't work, then simply remove the power button (P Power Button) entirely. With my brother's phone, I simply removed the button and reversed it. This way, there is no way for the two to make contact, even when pressed. We gorilla taped it into position.
*Note: The issue with this fix was that the phone could not be turned off (unless you take off the tape and access the switch to turn it back on). I gave him my extended battery to ensure he would not run out, and Installed a custom Rom which allowed him to use the volume keys to wake his phone from sleep (this might come stock in previous versions of andoid--dunno though), and change the power key/lock screen key to long pressing the home button. That way there is no need for the power button as long as the phone is on. (We used Beanstalk Rom 4.3) for this and it has been working flawlessly. **Since installing custom roms and rooting only requires reboot, it is still possible with a phone with a power button issue.
3) How to stop the boot cycle: It might be quite obvious, but just to state it--in order to stop the reboot cycle and "unstuck" the power switch, simply press the power button down a few times patiently until it remains stable. **Pressing it harder does not increase your chances! Remember to be gentle because you are working with a switch that is already faulty!
*Note:When the power button is removed, you can use some non-metal pointy object to press down the power switch inside the phone. You want to do this carefully, as you will notice that even the slightest touch of the switch, even if you don't press the button down, will send it into loop. Once you get the phone on and stable. Seal up the hole and the phone should be fine as long as it doesn't shut off.
Forgive me, I don't know how to make tutorials. Tried to catch everything I ran into along the way, but I noticed it's quite wordy. Hope this helps someone!
itsfredo said:
Symptoms:
Extreme Case: Once phone is plugged in or battery inserted, phone vibrates constantly and never progresses further through the boot cycle.
Moderate Case: Phone is able to make it to Samsung logo, or sometimes even further, but never fails to reboot and remain stuck in this cycle.
Preliminary Case: Phone randomly reboots for no reason, or when power button is gently touched (not hard pressed)
Problem:
1) Either phone button is sticky for some reason (ewww) and gets stuck, causing phone to reboot.
2) Or, (more severe cases) the internal switch is beginning to malfunction (common) and needs to be replaced in order to really fix the problem.
Fixes:
1) If the button is sticky, simply clean it you sicko and quit being dirty. Plenty of guides on how to open the phone on Youtube. (This is not really a big issue though)
2) Faulty hardware is going to require some major work to be completely fixed.
Ghetto Fix:
Intro: My phone is showing preliminary issues of the common switch malfunction issue. I read around and it seems that Samsung just failed with that portion of the hardware. My brother's phone, on the other hand, was an extreme case and was basically a brick in my room for a few months until I decided to fix it. It's not a profound fix, so I'm sorry for those who really want this issue solved. If you do, I recommend either replacing the part yourself or taking it to a shop to repair it for you. This fix is for those of you who might have an fully functioning galaxy s2 laying around, with the exception of that stupid button.
1) You will need to know how to open up your phone. There are many guides on Youtube. Be very careful doing so.
2) Ghetto Button Fix (Two Options) *From here on I will have to make a distinction between the two senses of "power button" I am talking about: There is the power button on the logic board (LB Power Button [my term]) and the one on the outside of the phone---the (P Power Button [my term]) is the one you see and press when your phone is put together and working fine--the (LB Power Button) is the switch attached to the logic board
a. The first ghetto fix will work if your case is not too severe, and it will look less ghetto. When you open your phone and separate all the parts, you are left with a good view of the (P Power Button)--you will notice that a small rubbery rectangular portion of the power button--file that off completely to prevent the (P Power Button) from touching the logic board power button (LB Power Button).
*Note: This will not be a fix for more extreme cases because the (P Power Button) can still reach the (LB Power Button). This will only make it less likely for the two to make contact when you do not want it to. Also note that the issue is not with the two making contact, it is a faulty switch. Anything from a quick jolt or vibration, or even gravity can be enough to set it into a looped cycle.
b. If the first one doesn't work, then simply remove the power button (P Power Button) entirely. With my brother's phone, I simply removed the button and reversed it. This way, there is no way for the two to make contact, even when pressed. We gorilla taped it into position.
*Note: The issue with this fix was that the phone could not be turned off (unless you take off the tape and access the switch to turn it back on). I gave him my extended battery to ensure he would not run out, and Installed a custom Rom which allowed him to use the volume keys to wake his phone from sleep (this might come stock in previous versions of andoid--dunno though), and change the power key/lock screen key to long pressing the home button. That way there is no need for the power button as long as the phone is on. (We used Beanstalk Rom 4.3) for this and it has been working flawlessly. **Since installing custom roms and rooting only requires reboot, it is still possible with a phone with a power button issue.
3) How to stop the boot cycle: It might be quite obvious, but just to state it--in order to stop the reboot cycle and "unstuck" the power switch, simply press the power button down a few times patiently until it remains stable. **Pressing it harder does not increase your chances! Remember to be gentle because you are working with a switch that is already faulty!
*Note:When the power button is removed, you can use some non-metal pointy object to press down the power switch inside the phone. You want to do this carefully, as you will notice that even the slightest touch of the switch, even if you don't press the button down, will send it into loop. Once you get the phone on and stable. Seal up the hole and the phone should be fine as long as it doesn't shut off.
Forgive me, I don't know how to make tutorials. Tried to catch everything I ran into along the way, but I noticed it's quite wordy. Hope this helps someone!
Click to expand...
Click to collapse
Or you can remove the power button from the board completely and the outer assembly from the case. Essentially a hole use a paper clip to short the pins to power on/off
Or you can remove one of the volume button and replace it with the lower button
mecha2012 said:
Or you can remove the power button from the board completely and the outer assembly from the case. Essentially a hole use a paper clip to short the pins to power on/off
Or you can remove one of the volume button and replace it with the lower button
Click to expand...
Click to collapse
Thanks for this. This would be a better and more permanent fix in the sense that it would almost guarantee the switch will not act up.
The only thing is, I've seen tutorials on how to take off the button from the logic board and it requires some pretty crazy equipment. More specifically, in the tutorial I saw, the guy used a hot air gun to melt the solder and some other fancy equipment.
Also, would using a paper clip be a danger to the entire logic board?

[Q] Power button hyper-sensitive

Hi all,
I've had some problems with my S3 power button. It's behaving like it's being pressed when it isn't. Just slightly brushing it, without depressing the button, is registering a press. Pressing the button is behaving like the button is being held.
I've read a number of possible fixes. I tried software options, just to be sure (cleared cache, factory reset). But this is almost certainly a hardware problem.
I stripped the phone down and the physical button itself looks absolutely fine. It is interacting as it should with the internal button on the motherboard. The issue seems to be that the internal button attached to the motherboard (the little white button) is registering clicks even when it's not being fully depressed.
The phone did have some water damage about 6 months ago. I wonder if this could be causing the the phone to mess up now?
I even tried a fix that many people seem to think works: smacking the crap out of the power button itself. It had no affect on my phone - I think that "fix" that is for a power button that is stuck depressed and not a power button registering phantom clicks/being hyper-sensitive.
So I suppose I have the following questions:
1) Has anyone else experienced similar problems and, if so, did they get it fixed?
2) My plan is to try replacing the motherboard/logic board and see if that helps. Does that sound like the best fix or is it overkill?
3) If I'm replacing the motherboard, does it need to be an I747 motherboard or will any S3 model work fine?
4) What's the best source for a motherboard? I don't mind if they're used or refub so long as they work.
Any advice you can offer is welcome.
Cheers.
BenScopato said:
Hi all,
I've had some problems with my S3 power button. It's behaving like it's being pressed when it isn't. Just slightly brushing it, without depressing the button, is registering a press. Pressing the button is behaving like the button is being held.
I've read a number of possible fixes. I tried software options, just to be sure (cleared cache, factory reset). But this is almost certainly a hardware problem.
I stripped the phone down and the physical button itself looks absolutely fine. It is interacting as it should with the internal button on the motherboard. The issue seems to be that the internal button attached to the motherboard (the little white button) is registering clicks even when it's not being fully depressed.
The phone did have some water damage about 6 months ago. I wonder if this could be causing the the phone to mess up now?
I even tried a fix that many people seem to think works: smacking the crap out of the power button itself. It had no affect on my phone - I think that "fix" that is for a power button that is stuck depressed and not a power button registering phantom clicks/being hyper-sensitive.
So I suppose I have the following questions:
1) Has anyone else experienced similar problems and, if so, did they get it fixed?
2) My plan is to try replacing the motherboard/logic board and see if that helps. Does that sound like the best fix or is it overkill?
3) If I'm replacing the motherboard, does it need to be an I747 motherboard or will any S3 model work fine?
4) What's the best source for a motherboard? I don't mind if they're used or refub so long as they work.
Any advice you can offer is welcome.
Cheers.
Click to expand...
Click to collapse
I had the exact same problem with mine, and unfortunately there's not much you can do about it as it's a hardware defect. I haven't tried replacing motherboards or anything, so that might help you. What I did to help with the problem was rerouting my power button to my volume up key so that I can use the power button as little as possible. The only time I use the power button now is when I need to power it on - which causes reboot loops sometimes.
Drisc0 said:
I had the exact same problem with mine, and unfortunately there's not much you can do about it as it's a hardware defect. I haven't tried replacing motherboards or anything, so that might help you. What I did to help with the problem was rerouting my power button to my volume up key so that I can use the power button as little as possible. The only time I use the power button now is when I need to power it on - which causes reboot loops sometimes.
Click to expand...
Click to collapse
Sucks.
I like the sound of your work around, though. Was it pretty simple rerouting the power button?
BenScopato said:
Sucks.
I like the sound of your work around, though. Was it pretty simple rerouting the power button?
Click to expand...
Click to collapse
Ditto, my power button is borked too. Ended up doing the same thing but I don't use my power button at all. I just use rom toolbox to reboot system/into recovery
Rerouting was simple for me as it's baked into the settings in the rom I'm on (ground zero) as it is with most custom ROM'S I've been on. If you're just running stock I'm sure there's an app in the market that'll work however I'm drawing a blank ATM
Sent from my SAMSUNG-SGH-I747 using Tapatalk
brianray14 said:
Ditto, my power button is borked too. Ended up doing the same thing but I don't use my power button at all. I just use rom toolbox to reboot system/into recovery
Rerouting was simple for me as it's baked into the settings in the rom I'm on (ground zero) as it is with most custom ROM'S I've been on. If you're just running stock I'm sure there's an app in the market that'll work however I'm drawing a blank ATM
Sent from my SAMSUNG-SGH-I747 using Tapatalk
Click to expand...
Click to collapse
I'm running CM.
I've had a look through the routing options. What I can't locate is a way to disable the power button completely. My main problem right now is the phantom clicks. I'd rather that button be dead.
Anyone know of a way I can make that happen in CM?
Nevermind. I just physically removed the power button. That did the trick.
For anyone interested, you can replace a faulty power button on the motherboard pretty easily and the parts are cheap. If I wasn't due an upgrade in 4 months I'd probably do that. No need to replace the whole motherboard.
Does anyone know the app to reroute the button? I too have the same problem.

Categories

Resources