[Q] Brick or not? Nice quest. - Samsung Galaxy Nexus

Greetings!
Recently i was trying to update CM11 with nightly 03142014 release and phone gone to bootloop mode. I'm able to boot only in ODIN mode because my VOLUME UP button is broken (no chances to fix). Is there any chance to boot into recovery or flash to stock from ODIN mode?
Appreciate your help.
Model: GSM/HSPA+
Boots only to ODIN
Problem: bootloop with CM11 03142014nightly release.

Evgeniydapp said:
Greetings!
Recently i was trying to update CM11 with nightly 03142014 release and phone gone to bootloop mode. I'm able to boot only in ODIN mode because my VOLUME UP button is broken (no chances to fix). Is there any chance to boot into recovery or flash to stock from ODIN mode?
Appreciate your help.
Model: GSM/HSPA+
Boots only to ODIN
Problem: bootloop with CM11 03142014nightly release.
Click to expand...
Click to collapse
Well I guess in your case it's a hardware brick but not really. You can... A. Take the phone apart and replace the volume buttons. (I have done this it's easier than it sounds really cheap too like a few dollars) or B. Odin back to stock and start over. If you can't boot all the way after flashing with Odin you can plug the phone in and "adb reboot recovery" It might work... Also you can try to adb reboot recovery during your current bootloop it might just work.

Solved.
DR3W5K1 said:
Well I guess in your case it's a hardware brick but not really. You can... A. Take the phone apart and replace the volume buttons. (I have done this it's easier than it sounds really cheap too like a few dollars) or B. Odin back to stock and start over. If you can't boot all the way after flashing with Odin you can plug the phone in and "adb reboot recovery" It might work... Also you can try to adb reboot recovery during your current bootloop it might just work.
Click to expand...
Click to collapse
Thank you very much! Googled "Odin back to stock", tried like ten of versions programs/software and finally restored. Just to them who met the same problem i put the link to download program here:
http m16.androidfilehost.com/download.php?registered=0&waittime=10&fid=23060877489996767&flid=4307&uid=&file_size=301938241&hc=0c9698ca8b6f2ddc9b725cfd61d8e03a3df6cf4c68dd2134cb2e28458638e2fe&tid=1394801735&download_id=3f1133754d25344c3670ff5e1fb98164&filename=Odin.stock+Gnex+I9250+4.3.zip&action=download

Related

SGH-I747 AT&T Softbricked Maybe Hard

Hi guys I just bought a SGH-I747 AT&T and the issue with it is it goes into Download mode just fine, works with Odin 3.7 loads a stock rom and then it sais reset but the phone doesn't reset just goes to black screen and then Odin sais Pass. I press the power button and Samsung appers and vibrates and goes back to black. When I try Recovery mode it show the blue writing on the left upper and the Samsung and then it goes to black screen. I put two different stock roms and same story. Kies won't recognize it and I installed recovery-clockwork-touch-6.0.4.3-d2att.tar to try to get into recovery mode and of course no luck. Don't know the history on this, so if anyone could help I would really appreciate it. Thanks in advance.
gica69 said:
Hi guys I just bought a SGH-I747 AT&T and the issue with it is it goes into Download mode just fine, works with Odin 3.7 loads a stock rom and then it sais reset but the phone doesn't reset just goes to black screen and then Odin sais Pass. I press the power button and Samsung appers and vibrates and goes back to black. When I try Recovery mode it show the blue writing on the left upper and the Samsung and then it goes to black screen. I put two different stock roms and same story. Kies won't recognize it and I installed recovery-clockwork-touch-6.0.4.3-d2att.tar to try to get into recovery mode and of course no luck. Don't know the history on this, so if anyone could help I would really appreciate it. Thanks in advance.
Click to expand...
Click to collapse
I found out that the phone had 4.1.1 on it and the guy tried to flash 4.2.2 and upon doing the odin mode flashing odin gave Firmware upgrade encountered an issue Please select recovery mode in Kies & try again So these are just some helpful facts for anyone who has gone through it. Thanks in advance for any help
gica69 said:
I found out that the phone had 4.11 on it and the guy tried to flash 4.22 and upon doing the odin mode flashing odin gave Firmware upgrade encountered an issue Please select recovery mode in Kies & try again So these are just some helpful facts for anyone who has gone through it. Thanks in advance for any help
Click to expand...
Click to collapse
What firmware were you trying to flash via Odin and are you sure the seller didn't previously flash (or try to flash) the 4.3 on it? If it wasn't higher than 4.3, then you may try recovery via Kies as follows ....
Install and launch Samsung Kies on your PC (not Kies 3). Open the Tools menu and select Firmware Upgrade and Initialization
Do not connect your phone to your PC yet. Remove the battery cover and record device info written in the battery compartment
In Kies, enter your phone model (SGH-I747)
Enter the phone serial number and click OK to all the security questions. Follow all the instructions on Kies
Connect the phone when prompted and follow the rest of the instructions
Wait for firmware upgrade to complete
Good luck!
If this doesn't work, then you may try flashing the 4.1.1 stock image via Odin. Look for the correct stock image via the following thread ...
http://forum.xda-developers.com/showthread.php?t=1739426
The one you want for Samsung Galaxy S3 AT&T (4.1.1) is I747UCDLK3
PLEASE don't try any of the above if you were already on the 4.3 bootloader as things will only get worse.
Larry2999 said:
What firmware were you trying to flash via Odin and are you sure the seller didn't previously flash (or try to flash) the 4.3 on it? If it wasn't higher than 4.3, then you may try recovery via Kies as follows ....
Install and launch Samsung Kies on your PC (not Kies 3). Open the Tools menu and select Firmware Upgrade and Initialization
Do not connect your phone to your PC yet. Remove the battery cover and record device info written in the battery compartment
In Kies, enter your phone model (SGH-I747)
Enter the phone serial number and click OK to all the security questions. Follow all the instructions on Kies
Connect the phone when prompted and follow the rest of the instructions
Wait for firmware upgrade to complete
Good luck!
If this doesn't work, then you may try flashing the 4.1.1 stock image via Odin. Look for the correct stock image via the following thread ...
http://forum.xda-developers.com/showthread.php?t=1739426
The one you want for Samsung Galaxy S3 AT&T (4.1.1) is I747UCDLK3PLEASE don't try any of the above if you were already on the 4.3 bootloader as things will only get worse.
Click to expand...
Click to collapse
I have already tried the I747UCDLK3 not from the link you gave me though. I did notice that the one you mentioned is a rooted stock do you think I should still do it? The rom flashes fine no errors in Odin but when it sais RESET the phone turns off the download mode and vibrates once then goes black then later Odin sais Pass but I cannot start it it just bootloops and vibrates and it stays that way As far as the Kies procedure you gave me don't I have to be in recovery mode for it to see the phone? I cannot get to that mode just download mode. Let me know thanks for your help
gica69 said:
I have already tried the I747UCDLK3 not from the link you gave me though. I did notice that the one you mentioned is a rooted stock do you think I should still do it? The rom flashes fine no errors in Odin but when it sais RESET the phone turns off the download mode and vibrates once then goes black then later Odin sais Pass but I cannot start it it just bootloops and vibrates and it stays that way As far as the Kies procedure you gave me don't I have to be in recovery mode for it to see the phone? I cannot get to that mode just download mode. Let me know thanks for your help
Click to expand...
Click to collapse
If you were successful in flashing via Odin, I would have suggested you try doing a hard wipe/reset in recovery. However, you said you can't get to recovery mode so this may not work. What happens when you try booting into recovery mode?
For Kies, you wouldn't have to be in recovery mode for the firmware restore to happen. Normally, you would have to connect your (powered-on) phone to your PC for it to be recognized by Kies. However, as you can't power on, we are forcing Kies to prepare the specific required firmware for your device by manually entering in the device information. Thus, when the phone is connected, you have firmware ready to make it work.
It may also be that the firmware you downloaded and flashed via Odin may not be the correct or full version. There are so many sources of "stock" firmware these days that one can never be too sure. You may go to Sammobile.com to download the stock firmware and compare the size of the extracted file to the one you used. The odin flashable tar.md5 file should be about 1.1Gb in size.
Larry2999 said:
If you were successful in flashing via Odin, I would have suggested you try doing a hard wipe/reset in recovery. However, you said you can't get to recovery mode so this may not work. What happens when you try booting into recovery mode?
For Kies, you wouldn't have to be in recovery mode for the firmware restore to happen. Normally, you would have to connect your (powered-on) phone to your PC for it to be recognized by Kies. However, as you can't power on, we are forcing Kies to prepare the specific required firmware for your device by manually entering in the device information. Thus, when the phone is connected, you have firmware ready to make it work.
It may also be that the firmware you downloaded and flashed via Odin may not be the correct or full version. There are so many sources of "stock" firmware these days that one can never be too sure. You may go to Sammobile.com to download the stock firmware and compare the size of the extracted file to the one you used. The odin flashable tar.md5 file should be about 1.1Gb in size.
Click to expand...
Click to collapse
When I go in recovery it shows blue writing in left upper corner and Samsung logo and then black screen. I think I did use the Sammobile firmware at 1.1. My clock in download mode shows 6. I don't think that would affect it though. Could it be that Odin doesn't really write the firmware that's why flashing doesn't change anything? I don't think the jig would do anything maybe sending it for a jtag reflash is the trick.
I am lost for now. If you guys can think of anything new let me know and thanks again.
gica69 said:
When I go in recovery it shows blue writing in left upper corner and Samsung logo and then black screen. I think I did use the Sammobile firmware at 1.1. My clock in download mode shows 6. I don't think that would affect it though. Could it be that Odin doesn't really write the firmware that's why flashing doesn't change anything? I don't think the jig would do anything maybe sending it for a jtag reflash is the trick.
I am lost for now. If you guys can think of anything new let me know and thanks again.
Click to expand...
Click to collapse
You didn't mention if you tried the Kies option. I had a similar problem once when upgrade to 4.1.1 via Kies failed during the process and that was how I was able to recover. However, since you bought this from the secondary market, there is no way of telling for certain what the previous owner did wrong which would have been useful for recovery options.
One of the nice things about Odin is that you usually know the results immediately. If it says Pass, therefore, that's likely what it means. So Odin did flash something. But what did it flash? The counter you saw in download mode shows how many custom system installations there have been and 6 does show there has been some previous heavy tinkering with the phone. As you are still able to get into download modes, I would suggest you try flashing custom recovery (TWRP or CWM) via Odin. If this works and you are able to get into recovery mode, you may then try doing a hard wipe/reset via recovery. You may also try flashing the other (rooted) 4.1.1 file via Odin. At this stage, you really have nothing to lose in trying all options. I guess if you can get into recovery mode, the problem is almost solved as this leaves plenty of options.
A jig wouldn't help as that only gets you to download mode which, for now, you don't have a problem with. JTag should always be a last resort option only. Let me know how far it goes and good luck!
When flashing in Odin, did you check auto reboot? If you did, try flashing again but uncheck auto-reboot. When you see Reset in the status windows, disconnect the USB cable, pull out the battery, wait a few seconds until the phone completely shuts down, put back in the battery, get into recovery, wipe cache, do a factory reset, and reboot.
audit13 said:
When flashing in Odin, did you check auto reboot? If you did, try flashing again but uncheck auto-reboot. When you see Reset in the status windows, disconnect the USB cable, pull out the battery, wait a few seconds until the phone completely shuts down, put back in the battery, get into recovery, wipe cache, do a factory reset, and reboot.
Click to expand...
Click to collapse
This damn phone is starting to annoy me. I can still get into download mode but my phone gets usb device not recognized now. I have access to another I747 phone so my question is if I have access to the pit file from that phone can anything be done with the Debrick utility and a SD card with only download mode access? Thanks in advance.
Go into download and let us know what is shown on the screen.
audit13 said:
Go into download and let us know what is shown on the screen.
Click to expand...
Click to collapse
Odin Mode
Product Name: SGH-I747
Custom Binary Downloads: Yes (6 Counts)
Current Binary: Samsung Official
System Status: Official
Qualcomm Secure Boot: Enable
Green Android Icon Downloading...
Do not turn off target!!!
OK I plugged the USB in and out a few times and it allows to write every few tries. Back to my question can I do something in download mode if I have another i747 that I can copy stuff from? I also tried the suggestion to uncheck auto-reset pull the usb cable then the battery and try to go to recovery but it doesn't.Any suggestions are welcomed.
Try flashing a stock 4.1.1 rom from sammobile using Odin. Do not check auto reboot. When you see reset in the status window, disconnect the usb cable, pull the battery, replace the battery, boot into recovery, and wipe. I have done this numerous times on my i747m after flashing custom ROMs.
audit13 said:
Try flashing a stock 4.1.1 rom from sammobile using Odin. Do not check auto reboot. When you see reset in the status window, disconnect the usb cable, pull the battery, replace the battery, boot into recovery, and wipe. I have done this numerous times on my i747m after flashing custom ROMs.
Click to expand...
Click to collapse
I will try it again I think I already did but when I put the battery back and click the Vol+ Home Power I get the blue writing and then black screen. Should I wait like 10 min on the black screen or it should be quick. Thanks
Keep holding the buttons until the blue writing disappears and the green android appears with the green progress bar.
audit13 said:
Keep holding the buttons until the blue writing disappears and the green android appears with the green progress bar.
Click to expand...
Click to collapse
Is there an unbrick.img for 4.1.1 or 4.1.2 I noticed that there are files for 4.3 that allow you to go in recovery and erase stuff reinstall. Let me know cause I sure couldn't find it.
If u can get it into download mode u are never ever hard bricked my friend...take it from a guy who had to dust off his old galaxy sll last weekend & still can't get into d/l mode on my s3 after a week & even with a jig lol
Sent from my SGH-T989 using xda app-developers app
gica69 said:
Is there an unbrick.img for 4.1.1 or 4.1.2 I noticed that there are files for 4.3 that allow you to go in recovery and erase stuff reinstall. Let me know cause I sure couldn't find it.
Click to expand...
Click to collapse
The unbricking image only helps you get into download mode from where you can work your way up the rest of the food chain. As you can already get into download mode without difficulties, I doubt if that's what you really need. You are also able to flash ROMs successfully in download mode via Odin so you've gone far up on the food chain already. Perhaps you are not doing the recovery thing correctly enough. Like Audit said, you need to continue holding down the Volume Up and Menu buttons whilst releasing the Power button after you see the first flash until the recovery menu appears and then do a hard wipe/reset.
Perhaps you could also try flashing TWRP via Odin if CWM isn't working.
Larry2999 said:
The unbricking image only helps you get into download mode from where you can work your way up the rest of the food chain. As you can already get into download mode without difficulties, I doubt if that's what you really need. You are also able to flash ROMs successfully in download mode via Odin so you've gone far up on the food chain already. Perhaps you are not doing the recovery thing correctly enough. Like Audit said, you need to continue holding down the Volume Up and Menu buttons whilst releasing the Power button after you see the first flash until the recovery menu appears and then do a hard wipe/reset.
Perhaps you could also try flashing TWRP via Odin if CWM isn't working.
Click to expand...
Click to collapse
I already tried holding the Home and Volume up buttons for 4-5 minutes at which point my fingers got a bit tired. The reason I wanted the unbrick.img is that I am now having issues with the computer recognizing the device in usb. I plugged and unplugged so many times that it no longer works that way so I wanted to do it via sd card. The unbrick.img gets you in recovery mode and download mode as it allows you to boot from the card not from the internal HD. But the only ones I have seen are for the 4.3 issues. And I tried It but did not put my device in recovery.
gica69 said:
I already tried holding the Home and Volume up buttons for 4-5 minutes at which point my fingers got a bit tired. The reason I wanted the unbrick.img is that I am now having issues with the computer recognizing the device in usb. I plugged and unplugged so many times that it no longer works that way so I wanted to do it via sd card. The unbrick.img gets you in recovery mode and download mode as it allows you to boot from the card not from the internal HD. But the only ones I have seen are for the 4.3 issues. And I tried It but did not put my device in recovery.
Click to expand...
Click to collapse
I couldn't find one either although you may be able to create yours using the command line posted in the thread below ...
http://forum.xda-developers.com/showthread.php?t=2549068
You may also try using a jig to get back into download mode. Have you, however, considered exercising any buyer protection options you have on the phone since, it would appear, the guy sold you a lemon?

[HELP!] Odin Firmware flash failed at hidden.img. Stuck in DL Mode. T700. Plz Help Me

Hi Everyone,
I am a new owner of a soft-bricked SM-T700. I am feeling very down and need some advice. I will be as thorough as I possibly can and I would truly, truly appreciate some help and advice from you kind folks. This is the first time I have had a bricked device out of my many Android devices.
My PLAN:
-Root
-Custom Recovery
-Nandroid Backup
-Backup EFS
-Flash stock western country firmware
What HAPPENED
Today I bought a wifi T700. I bought it in my hometown, which is China. Whenever I buy a new Android device in China my first action is to ensure it doesn't have any hardware/warranty issues. I then go about reflashing a western firmware so I can use Google services.
1) First I rooted using CF-Auto Root. That worked fine. I confirmed that I had root using an app called root checker.
2) I then attempted to flash TWRP recovery by following the instructions here: http://teamw.in/project/twrp2/238
- First I tried flashing the .tar file using Odin. As soon as I hit 'Start' Odin froze and I got the Windows error saying "Odin Downloader Has Stopped Working", asking to close the program. I close the program. I tried this several times then rebooted. It seemed as though the phone booted fine.
- I then tried using their own software, TWRP manager, here: http://jmzsoftware.com/twrp-manager-4. This app just crashed every time I booted it. I submitted an error log.
- I then tried using 'Flashify' as suggested by someone here on XDA. Once I did that it said flashed successfully and would I like to reboot. I said yes. This is when my troubles started.
3) Upon reboot it immediately booted into a sparse looking 'Download Mode' screen, all in English (the normal one on mine has some Chinese too) without the volume button options to reboot or continue. It just went straight into this screen.
After trying to reboot the phone using several power button holds and key combinations, it appears I am stuck in this screen, so I thought I had no chance of doing a NADROID backup as originally planned, so I decided to try my luck and flash the western firmware.
I tried to flash the version of the firmware provided here: http://forum.xda-developers.com/showthread.php?t=2798835
http://www.androidfilehost.com/?fid=23501681358556680
It got all the way through the install until it hit the hidden.img and then failed. I've attached a screen capture.
A few notes;
I have tried using two different USB cables (the one that came with it, and the one that came with my HTC One). I have tried several USB plugs, including the one in the back of my PC. I allowed Odin to do it's MD5 check and it said the file checks out.
I have tried using the Kies emergency Firmware recovery. Pffft! As it that was going to work. Damn Kies.
I sound like I've still got my sense of humor, but actually I am really cut up about this. It is so much money for a tablet and now it is useless unless I can get s firmware that will flash.
I don't have my stock Chinese firmware. That is T700ZCU1ANF4/T700CHN1ANF4/T700ZCU1ANF4/T700ZCU1ANF4 (CHN).
Questions:
Does anyone know where I could find the stock Chinese firmware to try flashing back to that?
Does anyone have the .PIT file and instructions on how to flash that, because I have read in other threads that it solves the hidden.img problem.
Does anyone know why this may have happened and have any alternative suggestions?
Could it have been the TWRP that actually caused this? The thread here indicates others aren't having trouble. Why would it have frozen for me?
I will try anything at this point. I am desperate.
Thanks so much in advance. Please come through XDA! Please come through Galaxy Tab S owners!!!!!!
-------------------------------------------
CLOSURE EDIT: I managed to flash Australian firmware, after reinstalling Kies, uninstalling and reinstalled the device drivers. I also made sure all Kies processes were killed before flashing with Odin.
For people in a similar situation I would urge them to have patience and keep trying to flash stock firmware.
Private Message UpInTheAir and see what he thinks.
Well let me start out by saying i have done some truely horrible things to my tablet in the proceas of porting CM 11. Bad kernels, messing up the partitions, you name it ive probably done it at this point.
I would try using heimdall. Flash one of the recoveries.. and try formatting your partitions.
The program crashing is when you should back off from trying to flash. Reassess what you did and what happened and if it's failing at a point flash the stock back before rebooting.
Continuing blindly was the problem. On something as expensive as a tablet never continue past a point where something goes wrong without reflashing back to stock and starting again.
As eousphoros said Use heimdall and flash a recovery.
Good luck.
eousphoros said:
Well let me start out by saying i have done some truely horrible things to my tablet in the proceas of porting CM 11. Bad kernels, messing up the partitions, you name it ive probably done it at this point.
I would try using heimdall. Flash one of the recoveries.. and try formatting your partitions.
Click to expand...
Click to collapse
Hi All,
Thanks for taking the time to reply.
You are certainly right that it is my fault and I should have stopped at some point and reassessed what was happening.
Can you please give me some more information about the steps you have offered? I am researching heimdall now, but if you could give some steps or advice that would be much appreciated.
It's probably going to be difficult because I assume we are in different timezones. I will persevere and try to get this worked out.
I have downloaded Heimdall and understand that it is an alternative to using Odin.
I currently have three questions about Heimdall.
1. Do I need to do the install drivers step if I have already installed the drivers for my device? Is this some step that actually replaces the current drivers with ones that are required for Heimdall to operate? I ask them because when I list USB devices, my tab is not shown up as Samsung Composite Device. It is actually shown as two separate entries, looking like generic USB entries.
2. Do I need to have a valid PIT file in order to run a custom Heimdall flash?
3. Which partition should I select if/when I run the Heimdall flash?
I'm dying a little inside every time I look at my tablet
Install heimdall
Download a recovery, I am going to pimp mine. http://forum.xda-developers.com/galaxy-tab-s/general/cwm-recovery-6-0-5-0-galaxy-tab-s-8-4-t2824099.
Run sudo ~/git/Heimdall/heimdall/heimdall flash --RECOVERY cwm6.0.5.0-2.img. Wait for it to complete, your tablet will reboot and will probably fail like it has been.
Hold down Power + Vol Down + Home button... wait for the "Press vol up to continue, press vol down to cancel"
Press vol down to cancel, then immediately hold down Power + Vol Up + Home button till you see the recovery screen pop up.
If you get the recovery screen your tablet can probably still be saved. Woo!
So then download http://forum.xda-developers.com/showthread.php?t=2798835 (Which i think you already have)
Unzip it, there will be a tar file. tar xvf T700....something.tar.md5 -C some_directory
You will get a bunch of img files. From those you should be able to finish the recovery and hopefully return full function to your device. (Which unless something is physically broken you will most likely be able to do.) Good Luck! And again this is all done at your own risk, please dont sue me.
eousphoros said:
Install heimdall
Download a recovery, I am going to pimp mine. http://forum.xda-developers.com/galaxy-tab-s/general/cwm-recovery-6-0-5-0-galaxy-tab-s-8-4-t2824099.
Run sudo ~/git/Heimdall/heimdall/heimdall flash --RECOVERY cwm6.0.5.0-2.img. Wait for it to complete, your tablet will reboot and will probably fail like it has been.
Hold down Power + Vol Down + Home button... wait for the "Press vol up to continue, press vol down to cancel"
Press vol down to cancel, then immediately hold down Power + Vol Up + Home button till you see the recovery screen pop up.
If you get the recovery screen your tablet can probably still be saved. Woo!
So then download http://forum.xda-developers.com/showthread.php?t=2798835 (Which i think you already have)
Unzip it, there will be a tar file. tar xvf T700....something.tar.md5 -C some_directory
You will get a bunch of img files. From those you should be able to finish the recovery and hopefully return full function to your device. (Which unless something is physically broken you will most likely be able to do.) Good Luck! And again this is all done at your own risk, please dont sue me.
Click to expand...
Click to collapse
First of all, let me just say that OH MY F#@$ING GOD I THINK THE NIGHTMARE IS OVER!!!! I managed to flash the Australian Firmware successfully. It has now booted fine, I have factory reset and I am in the process of setting up the device afresh.
Having said that, when I do come to reroot and install a custom recovery, I will definitely take a look at yours. Was this here 12 hours ago? I looked and couldn't find anything about CWM except for a short thread and an unofficial port. I have never tried TWRP before and I will avoid it like the plague in the future. I have NEVER had trouble with CWM.
When (if ever) I get the nerve up to give this another go, I will try your CWM.
Thanks again.
I am so relieved right now.....
And make a Nandroid first this time
Hey,
I had the exact same issue with my Galaxy Note 8, every time I tried to install European or custom Rom.
The only way to get the tab back was to flash with the Chinese firmware. You may find it easily on Baidu.
Since it happened also with a note 2 and note 3, I stopped buying Android device in China... Unless you can make sure that you buy a model coming from HK.
Hi everybody.
In order not to create another Thread I would like to leave a request for help in here while searching the answer myself.
I've messed up with SM-T700 and it is suffering a "near brick expirience" now. D:
I wanted to install the TWRP in order to backup the stock ROM before proceeding to anything else. So I put it in download mode. In Odin. 3.09 I put the TWRP under the AP section, the auto-reboot and f-reset were checked. (later I understood that I look at a different chrome tab and followed the instuction for auto-root flashing in via Odin instead of TWRP's. Stupid me) THen I proceeded with flashing and it was succesfull. After that I rebooted to recovery but it was not TWRP but stock. So I went to Download mode again and decided to repeat the procedure. Hower this time, and each time after that Odin stuck with the SetupConnection... The tab itself is stuck in Downloading Do not tur off target!! and does not react to any combinations of buttons.
Looking for a piece of advice here.
At least Odin is detecting the tab is a good sign right?
Attaching the photo and screenshot just in case.
ky3bmu4 said:
Hi everybody.
In order not to create another Thread I would like to leave a request for help in here while searching the answer myself.
I've messed up with SM-T700 and it is suffering a "near brick expirience" now. D:
I wanted to install the TWRP in order to backup the stock ROM before proceeding to anything else. So I put it in download mode. In Odin. 3.09 I put the TWRP under the AP section, the auto-reboot and f-reset were checked. (later I understood that I look at a different chrome tab and followed the instuction for auto-root flashing in via Odin instead of TWRP's. Stupid me) THen I proceeded with flashing and it was succesfull. After that I rebooted to recovery but it was not TWRP but stock. So I went to Download mode again and decided to repeat the procedure. Hower this time, and each time after that Odin stuck with the SetupConnection... The tab itself is stuck in Downloading Do not tur off target!! and does not react to any combinations of buttons.
Looking for a piece of advice here.
At least Odin is detecting the tab is a good sign right?
Attaching the photo and screenshot just in case.
Click to expand...
Click to collapse
Replying to myself: The tab began to respond to buttons so now I succesfully rebooted it and will continue with Rooting then recovery
Added: Rooted successful but the same problem as described above occured when I tryied to flash TWRP in Odin under PDA tab unchecked the auto-reboot
ky3bmu4 said:
Replying to myself: The tab began to respond to buttons so now I succesfully rebooted it and will continue with Rooting then recovery
Added: Rooted successful but the same problem as described above occured when I tryied to flash TWRP in Odin under PDA tab unchecked the auto-reboot
Click to expand...
Click to collapse
Yeah I've had a really bad experience with TWRP on this device. Try flashing a firmware from sammobile.com or elsewhere to at least get it up and running again. Try to do that as quickly as possible too, so you don't have to leave the device in download mode all night. I think that is what caused the battery swelling in my first device that I had to return.
I'm going to stick with CWM when I work up the courage to try again....
pierrotee said:
Yeah I've had a really bad experience with TWRP on this device. Try flashing a firmware from sammobile.com or elsewhere to at least get it up and running again. Try to do that as quickly as possible too, so you don't have to leave the device in download mode all night. I think that is what caused the battery swelling in my first device that I had to return.
I'm going to stick with CWM when I work up the courage to try again....
Click to expand...
Click to collapse
Hi thx for reply. Actually it managed to unstuck from Download mode in 10-15 minutes. It happened twice to me.
ky3bmu4 said:
Hi thx for reply. Actually it managed to unstuck from Download mode in 10-15 minutes. It happened twice to me.
Click to expand...
Click to collapse
Cool! So do you now have root and custom recovery?
pierrotee said:
Cool! So do you now have root and custom recovery?
Click to expand...
Click to collapse
Yeah))
TWRP installs OK via TWRP Manager
I installed TWRP Manager, selected 'klimtwifi' as the device, and it successfully installed TWRP 2.7.1.1 without a hitch.
From TWRP I then immediately performed a nandroid backup of everything but the caches to my microSD card and encountered no problems.
The last step was to enable writing to my microSD card by installing NextApp SDFix.
My SM-T700 is bricked as well and I tried to flash a custom recovery with Heimdall on Mac but it gave me the Error "Claiming Interface failed". Seems like you really need the pit.

Help! stuck at Samsung logo, can't get into recovery

Hi, I'm having trouble booting after flashing the stock jelly bean rom 4.3 from tmobile. Right now it is just stuck on the Samsung logo. The problem may have been that I had installed the slimkat Kitkat rom and tried to go back to stock tmobile rom which was jelly bean. (stupid I know)
The second problem is that my volume up button is broken so I can't hold it long enough to boot into recovery. I am able to get into download mode and use odin if I get lucky and struggle with the up button but it only works in short bursts as it's damaged on the actual board and not the rocker.
Is there any other way I can get into recovery? I can't boot into the os so rebooting from there is out of the question. I'm running out of ideas now.
any suggestions would be greatly appreciated.
Flashing stock was fine. Your roms version doesnt matter, its your base firnware that does. Whenever you go between tw and non-tw roms you have to factory reset or itll hang at boot, which is what is happening to you.
Since you flashed stock, i dont know if itll work or not, but if ADB is set up on your computer, connect while in download mode, open command prompt and type
Adb devices
This will start the service and tell you if its detected.
Next type
Adb reboot recovery
If thats not going to work, youre going to need to find a way to make an odin flashable cm rom (not sure if you can), or get the the volume button fixed.
I dont know of any other way to boot recovery if you cant boot your rom as well.
DocHoliday77 said:
Flashing stock was fine. Your roms version doesnt matter, its your base firnware that does. Whenever you go between tw and non-tw roms you have to factory reset or itll hang at boot, which is what is happening to you.
Since you flashed stock, i dont know if itll work or not, but if ADB is set up on your computer, connect while in download mode, open command prompt and type
Adb devices
This will start the service and tell you if its detected.
Next type
Adb reboot recovery
If thats not going to work, youre going to need to find a way to make an odin flashable cm rom (not sure if you can), or get the the volume button fixed.
I dont know of any other way to boot recovery if you cant boot your rom as well.
Click to expand...
Click to collapse
Thanks for the reply, I do have ADB set up but unfortunately when running the command on adb it's not finding any devices. Odin finds it ok. I also have the android toolkit but it looks like it only works if the phone boots into the os..
Well I got it working now. Playing with a piece of tin foil around the volume up button finally let me hold it long enough to get into recovery. Wiping the cache got it all working properly again. thanks again.
Nice fix man!
As for adb, I figured it wouldn't work, but was worth a shot in case I was wrong. Pretty sure that it requires an insecure kernel since it didnt work though.
And just remember in the future, every time you switch between TWO and nonTW roms you have to factory reset. Glad you got it working!

[Q] TWRP brick

OK, I did search and found nothing. So, I need to ask this somewhere, hopefully this is the place. The similar threads search did not seem to help much.
I have a Tab S 8.4 WiFi. I rooted it and was running Cyanogen 12. I noticed the TWRP 2.8.3.0 update, so I went to install it. TWRP manager kept crashing, so I went to the TWRP site and downloaded the SM-T 700 klimti wifi img file. I used Flashify to flash this, as I have done numerous times. I wish I'd extracted and flashed the zip in TWRP, but I did not. Everything acted normal but when the tab went to boot up it got to the Black screen that announces Samsung Galaxy S, SM-T700, Powered by android. This was it. It flashed this screen constantly every second or so. Non stop. There was nothing any button combination would do. Except it will go into download mode. Nothing else. No hard reset, nothing. Download mode is it. I spent lots of time looking at various tutorials to see what I'd missed, nothing but download mode. So, I had Odin on the computer and the latest firmware from SamMobile, so I figured I could start over and get the tablet functioning. I've used Odin a fair amount before, including the original Galaxy, S III, S4, so I'm not unfamiliar with the process. I've yet (until now) had the privilege of having a wreck like this one.
So, Odin acts like it is doing its thing, runs through all the steps, says at the end Pass and all threads succeeded, none failed. At the end of the Odin process the tablet acts like it is booting. Up comes the Samsung name with the Bluish sparkly oval along with the standard Samsung tones we hear heading into the boot. That is as far as it goes. The blue and pink colors fade out and I am left with a black screen with SAMSUNG in the middle. Again, no button combination except download mode works at all. It just stays there. Pass showing proudly on the Odin screen (EDIT: I left it there for an hour or so to see if boot would finish before disconnection). I downloaded and tried flashing all of the various firmwares, same result. I even let the battery drain to zero hoping that would shut it off. It seemed to, but the results were the same, only the download mode combination will do anything. The power button starts up the phone in an initially normal manner, but it goes right to SAMSUNG in a black screen.
EDIT 2: I used the Cellular South firmware, saw nothing else US and thought I remembered reading this was what worked here.
There is likely user error here (and realize I might kick myself in the end...Oh wait, I already have), but I've run in circles enough to realize I'm probably doing the same sequence with the same error and I not able to see what it is.
Does anyone have any idea what is wrong or how to fix this? I hope it is fixable. I had hope since download and Odin at least go through the motions. I would greatly appreciate any advice, suggestions, or help. Thanks in advance.
Since you installed cm12 my guess is that its trying to switch back to davlik runtime. Have you tryed flashing twrp, then transfer another rom/custom rom too it and flash it with twrp?
DUHAsianSKILLZ said:
Since you installed cm12 my guess is that its trying to switch back to davlik runtime. Have you tryed flashing twrp, then transfer another rom/custom rom too it and flash it with twrp?
Click to expand...
Click to collapse
I did wonder about conflicts, including dalvik vs art. But I have a tab I can't do anything with except go to download. Since I tried stock firmware flashes, I imagine root is toast and so is flashing another TWRP, assuming I can do that with Odin. Never tried zip files with Odin. So short answer is no I have not tried flashing TWRP over Odin (which is now my only option). I also wondered if I was stuck with this paperweight until Samsung gets Lollipop to the Tab S, when I can get a stock 5.0 firmware from SamMobile, or someplace.
At any rate thank you.
SteveC485 said:
I did wonder about conflicts, including dalvik vs art. But I have a tab I can't do anything with except go to download. Since I tried stock firmware flashes, I imagine root is toast and so is flashing another TWRP, assuming I can do that with Odin. Never tried zip files with Odin. So short answer is no I have not tried flashing TWRP over Odin (which is now my only option). I also wondered if I was stuck with this paperweight until Samsung gets Lollipop to the Tab S, when I can get a stock 5.0 firmware from SamMobile, or someplace.
At any rate thank you.
Click to expand...
Click to collapse
What I mean is to flash twrp with odin then flash zips with twrp. If you cant reboot into recovery, if you installed adb then yoi can do adb reboot recovery.
I`m having same issues. I was on stock rooted ROM and flashed latest TWRP from the app. Now I`m stuck in bootloop.
EDIT: flashed TWRP 2.8.1.0 via Odin and everything works fine now.
senel said:
I`m having same issues. I was on stock rooted ROM and flashed latest TWRP from the app. Now I`m stuck in bootloop.
EDIT: flashed TWRP 2.8.1.0 via Odin and everything works fine now.
Click to expand...
Click to collapse
Thanks. When Christmas stuff winds down, I will give Odin a go. Thanks to both of you who answered. Merry Christmas.
OK, Odin says the TWRP is successful, goes through all motions, up to and including PASS. The tablet still will only go into Download Mode. At this point I'm wondering about trying Kies. Also thought what might happen if I unchecked Auto reboot in Odin and tried that again.
SteveC485 said:
OK, Odin says the TWRP is successful, goes through all motions, up to and including PASS. The tablet still will only go into Download Mode. At this point I'm wondering about trying Kies. Also thought what might happen if I unchecked Auto reboot in Odin and tried that again.
Click to expand...
Click to collapse
? You can boot into twrp? It should be power, home, vol up buttons. And to force reboot its power, home and vol up and down buttons at the same time.
DUHAsianSKILLZ said:
? You can boot into twrp? It should be power, home, vol up buttons. And to force reboot its power, home and vol up and down buttons at the same time.
Click to expand...
Click to collapse
No, the power, home, volume up does nothing, I even held it there for maybe 15 minutes. The power, home, and volume up/down gets the download screen, or rather it gets the warning screen about the dangers of flashing a custom OS. Continue goes into download and reboot get me the same old attempt to reboot then stuck on Samsung screen. That last is the ONLY button combination I can get to work.
I'll let the thing use up the battery and shut itself off and try the manual reboot to recovery again. I've chased this thing around so much I'm likely in a boot loop myself and can't see my error.
SteveC485 said:
No, the power, home, volume up does nothing, I even held it there for maybe 15 minutes. The power, home, and volume up/down gets the download screen, or rather it gets the warning screen about the dangers of flashing a custom OS. Continue goes into download and reboot get me the same old attempt to reboot then stuck on Samsung screen. That last is the ONLY button combination I can get to work.
I'll let the thing use up the battery and shut itself off and try the manual reboot to recovery again. I've chased this thing around so much I'm likely in a boot loop myself and can't see my error.
Click to expand...
Click to collapse
Hmm did you use the latest twrp? Ive alwayed use twrp 2.7. 1,1 Something. Never had problems in that version.
DUHAsianSKILLZ said:
Hmm did you use the latest twrp? Ive alwayed use twrp 2.7. 1,1 Something. Never had problems in that version.
Click to expand...
Click to collapse
Used 2.8.1.0. I had the issues trying to update to 2.8.3.0. I used 2.8.1.0 because it was working. I was thinking about trying the 2.8.3 because maybe I had a bad download and maybe a new flash might fix stuff.
Quick question, can Odin flash zip files? Never tried one.
SteveC485 said:
Used 2.8.1.0. I had the issues trying to update to 2.8.3.0. I used 2.8.1.0 because it was working. I was thinking about trying the 2.8.3 because maybe I had a bad download and maybe a new flash might fix stuff.
Quick question, can Odin flash zip files? Never tried one.
Click to expand...
Click to collapse
nope. Odin only flashes tars and files with md5 or a few otheres. You flash zips with twrp.
DUHAsianSKILLZ said:
nope. Odin only flashes tars and files with md5 or a few otheres. You flash zips with twrp.
Click to expand...
Click to collapse
Thanks, that's what I thought.
For whatever reason, this time the power, home, and volume up combination booted me into TWRP. Restored a backup and everything is up and running normally (at least so far).
I'm perfectly willing to admit error,but don't quite know where my error came in. I would swear I used the power, volume up, and home combination when I hit the download mode. But maybe not. I don't know why it worked now, except that I was inadvertently hitting the wrong combination, thinking I was doing it right. I remember thinking the first time it went to download mode, that I just did it wrong and used the wrong volume key. Thought I was more careful the succeeding tries.
At any rate thanks for the help. I will remember this particular lesson for a while .
hard brick
My sm-t700 hard brick with the last twrp... I don't know if it is the twrp but it's hard brick when I do a restore with twrp...now it is just dead... no power.. no nothing lol... j'ai été le échanger. . Vive future shop.. mais la j'ai peur de recommencer mon root et etc...
faztecnyk said:
My sm-t700 hard brick with the last twrp... I don't know if it is the twrp but it's hard brick when I do a restore with twrp...now it is just dead... no power.. no nothing lol... j'ai été le échanger. . Vive future shop.. mais la j'ai peur de recommencer mon root et etc...
Click to expand...
Click to collapse
Try this http://forum.xda-developers.com/showthread.php?t=2838473
DUHAsianSKILLZ said:
Try this http://forum.xda-developers.com/showthread.php?t=2838473
Click to expand...
Click to collapse
Thanks.. but I said hard brick and not soft brick..
SteveC485 said:
Used 2.8.1.0. I had the issues trying to update to 2.8.3.0. I used 2.8.1.0 because it was working. I was thinking about trying the 2.8.3 because maybe I had a bad download and maybe a new flash might fix stuff.
Quick question, can Odin flash zip files? Never tried one.
Click to expand...
Click to collapse
A lot of Tab S owners have had issue with TWRP 2.8.3. There is another thread on it. I installed 2.8.3 with Odin and it was pretty wonky. Went right back to 2.8.1.
If none of the methods worked for anyone try this. If your tablet keeps trying to boot into twrp or stuck at the galaxy tab s screen try this if you cant boot into download mode.
Let completely die. Then put it in the charger and quickly press the combination of buttons to get into download mode. That should over ride booting into twrp. another way is to plug it into your computer and try different combinations of buttons.
I have the samsung galaxy tab s 8.4 and I rooted it a few days ago and I thought to myself lets install a custom recovery, but before I did that I backed up my stock kernal and my stock recovery through flashify, also im on stock firmware, after I backed those things up I installed twrp 2.8.3.0 and I booted into recovery to back up my rom and data just in case I soft bricked my tablet like I used to do on my nexus 7, when trying to boot into twrp it went in to boot loop I have tried all button combination I know and have seen in this thread but none works except for going into download mode. I dont know if I should flash an older version of twrp and see if it works or should I install stock firmware on my device and im not sure what version of odin I should use if I flash a older version of twrp. The version I used to root my tablet is 3.07 of odin.

[Q] Help please Samsung Galaxy S3 unbrick.

Hello Everyone.
Please, I need some help. I was trying to downgrade an ATT Samsung Galaxy S3 from 5.0 to 4.1.1 and try to unlock it.
First, Try to flash with Odin 3.04, Odin 3.07 and Odin 3.09 with the firmware 4.1.1 from Samsung. It always failes.
So I rooted it , installed a team Win Recovery Project 2.6.3.1 and flashed a custom rom based on Android
4.1.2 thinking it will break the bootloader. Nothing.
I tried Emergency Recovery with Kies did not work.
In odin mode:
Product Name: SGH-I747
Current Binary: Custom
System Status: Custom
Qualcom Scoreboot: Enable
Warranty Bit:1
Bootloader AP SWREV:3
I spent hours on it. I don't know what to do.
Anyone has a idea to help me please?
Thanks you very much in advance.
If you can get into download mode, flash the latest Philz d2lte recovery using the tar.md5 file and Odin. Copy a ROM to an external SD card (I recommend the latest CM11), boot into recovery, flash the ROM, boot the phone. Once the phone boots, confirm your bootloader and modem version. I recommend not flashing anthing until you at least know your bootloader version.
Continuing to flash files without knowing the bootloader verson can hard brick you phone.
audit13 said:
If you can get into download mode, flash the latest Philz d2lte recovery using the tar.md5 file and Odin. Copy a ROM to an external SD card (I recommend the latest CM11), boot into recovery, flash the ROM, boot the phone. Once the phone boots, confirm your bootloader and modem version. I recommend not flashing anthing until you at least know your bootloader version.
Continuing to flash files without knowing the bootloader verson can hard brick you phone.
Click to expand...
Click to collapse
Thank you for your quick answer like you said i tried to flash cyanogen mod 11 and it aborted. How can I find out my bootloader version?
MEEEEEEEE said:
Thank you for your quick answer like you said i tried to flash cyanogen mod 11 and it aborted. How can I find out my bootloader version?
Click to expand...
Click to collapse
If you're on Philz touch, download AROMA file manager and store it on your external SD. You can get it here.
Boot into recovery and flash the file manager like you would install a ROM and it will open the file manager. Once you're up in the AROMA file manager, one of the menu options is to open a console. Once you're up in the console window the following command will tell you what bootloader you have loaded:
Code:
getprop ro.bootloader
That command will work from ADB shell in custom recovery too, if you happen to have ADB and all the drivers set up right on your computer.
What error did you get when flashing with Philz? Was it error 7?
Yes. It was a status 7. And I don't know what happens. Right now it looks hard bricked. I can not even it start it and put it on the downloading mode. When I plugged it to the power source without the battery. I have a big red led on and any responses. What is it? Can I go back to the downloading mode with a jig?
MEEEEEEEE said:
Yes. It was a status 7. And I don't know what happens. Right now it looks hard bricked. I can not even it start it and put it on the downloading mode. When I plugged it to the power source without the battery. I have a big red led on and any responses. What is it? Can I go back to the downloading mode with a jig?
Click to expand...
Click to collapse
Pull the battery, leave it out for a few minutes, then try to boot into recovery or download mode. This has cured some curious behavior for me a few times (just a shot in the dark though).
Another random thought, do you know how much battery power you had left? I'm a little surprised a failed CM flash would result in a hard brick when you still had download and recovery working before. Any chance the battery is dead? It won't charge without a working rom.
If that doesn't work and you can't get into recovery or download mode it might be time to move on to the debrick threads.
You may have to try a de-brick image. Status 7 usually occurs when the recovery is out of date.
jason2678 said:
Pull the battery, leave it out for a few minutes, then try to boot into recovery or download mode. This has cured some curious behavior for me a few times (just a shot in the dark though).
Another random thought, do you know how much battery power you had left? I'm a little surprised a failed CM flash would result in a hard brick when you still had download and recovery working before. Any chance the battery is dead? It won't charge without a working rom.
If that doesn't work and you can't get into recovery or download mode it might be time to move on to the debrick threads.
Click to expand...
Click to collapse
I tried to take the battery out and the flash is light on for a micro second but the phone does not boot. I can not go either in the recovery mode nor the downloading mode.
The is a custom rom on the phone. There is a slim kat v9 on it.
MEEEEEEEE said:
I tried to take the battery out and the flash is light on for a micro second but the phone does not boot. I can not go either in the recovery mode nor the downloading mode.
The is a custom rom on the phone. There is a slim kat v9 on it.
Click to expand...
Click to collapse
You did put the battery back in after pulling it for a couple of minutes, right? Looking back at my previous post it was poorly worded.
The fact that you went from working recovery and download to not working on a status 7 is curious. Usually status 7 errors are the developers trying to protect us from ourselves; your recovery is out of date, you are trying to flash a rom that isn't for your phone or doesn't like your bootloader, something like that. When you get a status 7, usually the recovery didn't actually do anything. It failed a safety check and quit. That's what made me wonder if maybe your battery just died.
So you flashed CM11 for the d2lte using the latest version of Philz? Did you flash anything else?
Actually I gave the cellphone to someone few days ago and he told me that I needed to unlock the bootloader and install EZ-unlock. Unlocked the bootloader. Philz is still on the recovery partition. The firmware flashed is slim kat v9. Since the bootloader has been unlocked. The phone does not want to start. I tried to take out the battery for few minutes. it does not change anything.
MEEEEEEEE said:
Actually I gave the cellphone to someone few days ago and he told me that I needed to unlock the bootloader and install EZ-unlock. Unlocked the bootloader. Philz is still on the recovery partition. The firmware flashed is slim kat v9. Since the bootloader has been unlocked. The phone does not want to start. I tried to take out the battery for few minutes. it does not change anything.
Click to expand...
Click to collapse
the phone wont start because the i747 bootloader does not come locked. what ez-unlock does for this device is effectively BRICK it!!!!! i know because thats how i bricked my first i747. now you really do need the debrick image. when plugged in , without battery does the led show red ?
http://forum.xda-developers.com/showthread.php?t=2549068
"all i can really do , is stay out of my own way and let the will of heaven be done"
Yes. The red led is showing when I plugged the device without the battery.
mrrocketdog said:
the phone wont start because the i747 bootloader does not come locked. what ez-unlock does for this device is effectively BRICK it!!!!! i know because thats how i bricked my first i747. now you really do need the debrick image. when plugged in , without battery does the led show red ?
http://forum.xda-developers.com/showthread.php?t=2549068
"all i can really do , is stay out of my own way and let the will of heaven be done"
Click to expand...
Click to collapse
MEEEEEEEE said:
Yes. The red led is showing when I plugged the device without the battery.
Click to expand...
Click to collapse
pretty positive sign of a brick if thats all you can get. check the link for the "de-brick" thread that i posted. remember that sometimes it takes more than one try , and while one sdcard will work for one phone , it may or may not work for another. just keep trying. good luck.:thumbup:
"all i can really do , is stay out of my own way and let the will of heaven be done"
Do I need to get a jig to un-bricked it?
MEEEEEEEE said:
Do I need to get a jig to un-bricked it?
Click to expand...
Click to collapse
nope. read the thread. a de-brick image and sdcard should do it.
"all i can really do , is stay out of my own way and let the will of heaven be done"
A jig would be helpful if the phone boots but you can't get into download mode.

Categories

Resources