Whenever I flash cm 10.2 cm 11 any rom at all I face the problem of no internet. So I go back to stock. I have my baseband, build # important stuff like that. I always have to take out my assert lines. So when I flash any rom the fine line will say;
;Mount
or something like that I delete all the assert lines and I was told to keep assert lines but just change them to my baseband and stuff. Any help would be appreciated. & btw the problem is it says Mobile State: Disconnected. But I'm in service too.
I have the same problem. Been searching for a while and trying different fixes, but doesn't seem to be working. I'm on ATT galaxy S3, tho. If someone's got a working ATT S3 and let me know exactly what ROM, gapp, modem, etc they used, would much appreciate it.
Keyonwise said:
Whenever I flash cm 10.2 cm 11 any rom at all I face the problem of no internet. So I go back to stock. I have my baseband, build # important stuff like that. I always have to take out my assert lines. So when I flash any rom the fine line will say;
;Mount
or something like that I delete all the assert lines and I was told to keep assert lines but just change them to my baseband and stuff. Any help would be appreciated. & btw the problem is it says Mobile State: Disconnected. But I'm in service too.
Click to expand...
Click to collapse
More info is needed, such as carrier. I'm guessing either Virgin Mobile or Boost if you need to remove asserts on any of the pre-unified builds (this would hold true for any ROM that has switched to d2lte from d2spr). If that is the case, then you don't have the correct APN's configured. Also, it usually doesn't hurt to be running the most current modem (MK3 for Sprint, MK5 for VM/Boost). Again, the more info the better, then people don't have to play Twenty Questions in order to get to the heart of the matter.
This may work...
So, after trying countless options that i found on this site, and after dozens of flashing roms, modems, kernels, booloaders, restores, etc... turns out that i was doing everything right and there was nothing wrong with the install or the phone itself. After contacting my carrier (PTEL Mobile) for the third time, (first time they told me they had an outage, second time they told me to set the APN setting correctly - neither of which was incorrect on my end or the cause), they said they will try RESETting the DATA on their end. And guess what - that worked.
If you think you did everything correctly but still not getting data, i suggest you make your provider to do the same, or at least pry them as much as you can about your problem and what they can do about it. I wasted to much time and effort (my poor phone) on this and the solution was simple, and not my fault. Hope this helps others.
Mr. Struck said:
More info is needed, such as carrier. I'm guessing either Virgin Mobile or Boost if you need to remove asserts on any of the pre-unified builds (this would hold true for any ROM that has switched to d2lte from d2spr). If that is the case, then you don't have the correct APN's configured. Also, it usually doesn't hurt to be running the most current modem (MK3 for Sprint, MK5 for VM/Boost). Again, the more info the better, then people don't have to play Twenty Questions in order to get to the heart of the matter.
Click to expand...
Click to collapse
Hiya, I'm currently having the same problem as the OP. Mobile state disconnected but it says I am in service. Using latest version of Philz recovery and I flashed the most recent nightly of the Cyanogenmod 11 -4.4.2 KitKat (April 5th, 2014).Carrier is Virgin Mobile, using Samsung Galaxy SIII SPH-L710. PRL is most recent one 33030 and modem is MK5. I did however, flash the rom without deleting the assert lines, since I did not know I had to delete some assert lines. Any help with this? Thanks.
S0lstice said:
Hiya, I'm currently having the same problem as the OP. Mobile state disconnected but it says I am in service. Using latest version of Philz recovery and I flashed the most recent nightly of the Cyanogenmod 11 -4.4.2 KitKat (April 5th, 2014).Carrier is Virgin Mobile, using Samsung Galaxy SIII SPH-L710. PRL is most recent one 33030 and modem is MK5. I did however, flash the rom without deleting the assert lines, since I did not know I had to delete some assert lines. Any help with this? Thanks.
Click to expand...
Click to collapse
Deleting asserts is only for d2spr specific builds, that doesn't apply to d2lte builds (hence the reference to "pre-unified builds" in my first post). Your issue is most likely also related to APN's. However, there are also known data issues on a lot of the latest CM nightlies, and also on the ROM's that rely heavily on CM as a code source. I would strongly recommend reading the last several pages of the thread for any ROM that falls into this category in order to see what other users are reporting along these lines.
CM11 No Mobile Network
Hey guys,
Noob here. I'm running CM11-20140428-NIGHTLY-jflte on a Galaxy S4 GT-i9507(international, optus) but bootscreen now says 9505(not sure if that's important).
I've had Mobile Network State: Disconnected for the last three nightlies. On CM11 M3 it was working all good, but now no luck.
So I've tried a few things and I've come to the point where I'm going to try the factory reset then reflash CM11 and fingers crossed it will work.
Can anyone talk me through the proper procedure for this? I've made a full backup on my external SD using CWM 6.0.4.7 and transferred it to
computer just in case. So would anyone be awesome enough to take me through it step by step.
Cheers,
hhmmm
Use Rom Manager app and Fix Perrmisson
I install a bunch of roms on my dadz s3 and had 2 DirtyFlash it
And then used Wifi 2 get the app itselfz and it fix'd 88 permission
Idk jus tryn 2 help
Had sumthing 2 do w Gapps causing my issue
CM11 No Mobile Network
Ickyz said:
Use Rom Manager app and Fix Perrmisson
I install a bunch of roms on my dadz s3 and had 2 DirtyFlash it
And then used Wifi 2 get the app itselfz and it fix'd 88 permission
Idk jus tryn 2 help
Had sumthing 2 do w Gapps causing my issue
Click to expand...
Click to collapse
Just Fixed Permissions using Rom Manager, still no good.
Stock no APN settings at all
I have looked everywhere and found nothing for the last 3 weeks. I have a stock, sprint S3 on straight talk (my son's phone) it will not get 4g lte data what so ever. My phone is the exact same phone, and it does get 4g lte data. I tried all the basics ##72786# data on off check airplane mode...nothing. Mobile network state is "disconnected". So I opened data ##3282# to compare apn settings with my phone. I made sure everything matched, and when I get to "LTE APN Settings" I open it up, and nothing is there except APNs nothing, blank. Also missing is "Dial Up Networking" that option does not exist on my son's phone. He updated to kitkat (uggh) but the problem was present before that. Checked the phone, and it is not rooted. Funny thing is the phone updates with 4g lte running after dialing ##72786#, but that goes away after it completes. Texting works, but no mms (pictures etc.) and if I set it to cdma only it gets 3g, otherwise no data at all. Anybody?
Related
This thread is a place for people to ask questions and get answers about CM 10.1 Nighty and Official when it comes out. This thread is the proper place for these kind of questions for now.
Link to CM 10.1 Nightly
http://jenkinsmanifest.clockworkmod.com/device/d2att/all
CM 10.1 Changelog credit lisek99
http://10.1.cmxlog.com/?device=d2att
4.2 GAPPS Credit Mike Ramsay
http://goo.im/devs/itsmikeramsay/gapps-jb-20121212-signed.zip
Ktoonsez 4.2 Kernel
http://forum.xda-developers.com/showthread.php?t=1871946
CyanogenMod's Progress
http://review.cyanogenmod.org/#/q/status:merged,n,z
itsmikeramsay's rendition of CM 10.1
http://forum.xda-developers.com/showthread.php?t=2039995
It has "..a few cherry-picks. We're shooting for that sweet spot between CM10.1 and AOKP."
Euroskank CM 10.1 kang d2att
http://forum.xda-developers.com/showthread.php?t=1806921
has cherry picks as well
Common Flash Process
1. wipe cache/dalvik
2. wipe system
3. factory reset
4. wipe data
5. TWRP users wipe internal-wipes internal data that could corrupt something
6. flash rom
7. flash gapps
Do this if you have any unexpected problems.
If you want flash ktoonsez kernel but if you have problems follow the flashing procedure before posting about problems/questions
Possible Data Fix
Alright, for anyone having issues with the CM10.1 "pre-release" builds (official or otherwise) not allowing you to keep a connection, here's how to fix it:
Download one of the modem files for your device (read!) in the OP of the modem thread. Any of the options will work, pick the one you want.
Keep that ZIP on your EXTERNAL storage. You need to be able to find it from CWM/TWRP.
With CM10.1 running, disable data from System Settings > "More..." (under Data Usage) > Mobile Networks > "Data enabled" (uncheck it)
Reboot into recovery. (Long-press Power, "Reboot", "Recovery", [OK])
Flash the modem from step 1.
Clear Cache and Dalvik Cache.
Reboot back into CM10.1.
Wait 30 seconds!
Enable data from System Settings > "More..." (under Data Usage) > Mobile Networks > "Data enabled" (check it).
You should have data within 10-20 seconds!
If this doesn't work, you might need to reset your APNs to default. This will only happen if you make changes to your APNs, so go into the APN list and press the menu key and hit "Reset to defaults". Then start over at step 1.
To prevent this problem, you should disable data before shutting off your device. You can enable it 30 seconds after boot and it should work again. If you get stuck in the "disconnect-loop", repeat these steps.
Themes
Sense 4 10.1 theme (might work for other roms)
http://forum.xda-developers.com/showthread.php?t=2051326
My dataaa, oh my dataaaa.
I almost have everything working, however I can't seem to get my 4G data to work.
khep24 said:
I almost have everything working, however I can't seem to get my 4G data to work.
Click to expand...
Click to collapse
1) Do you mean LTE, HSPA(+), or something else? HSPA(+) doesn't seem to work very well under 4.2 conditions.
2) Who's your carrier?
smelenchuk said:
1) Do you mean LTE, HSPA(+), or something else? HSPA(+) doesn't seem to work very well under 4.2 conditions.
2) Who's your carrier?
Click to expand...
Click to collapse
I'm sorry for being vague I thought this whole thread was just for GS3 AT&T version, but LTE data for AT&T. Thanks
khep24 said:
I'm sorry for being vague I thought this whole thread was just for GS3 AT&T version, but LTE data for AT&T. Thanks
Click to expand...
Click to collapse
The same model of phone (well, more or less) is used for several Canadian carriers, which is why I'm asking.
Just to confirm: are you getting a data connection on something other than LTE? If so, that narrows down the number of things that could be wrong - my two immediate guesses would be that you have the wrong APN set or you have the wrong network type set in either Settings -> More -> Mobile Networks or in the Phone Info menu you can get by dialing *#*#4636#*#* (these are both known to happen immediately after flashing something).
smelenchuk said:
The same model of phone (well, more or less) is used for several Canadian carriers, which is why I'm asking.
Just to confirm: are you getting a data connection on something other than LTE? If so, that narrows down the number of things that could be wrong - my two immediate guesses would be that you have the wrong APN set or you have the wrong network type set in either Settings -> More -> Mobile Networks or in the Phone Info menu you can get by dialing *#*#4636#*#* (these are both known to happen immediately after flashing something).
Click to expand...
Click to collapse
There it goes , that did the trick thanks for the help. Now my GS3 is working perfectly with the update.
Are you getting a 4G logo on your bar? I cannot get anything but 3g,H, and H+. Mobile network setting set to LTE/GSM/WCDMA. any help would be nice, I seem to mainly get H+ and sometime switches to 3G.
Using ATT carrier.
Sent from my Nexus 7
sliverboyx2002 said:
Are you getting a 4G logo on your bar? I cannot get anything but 3g,H, and H+. Mobile network setting set to LTE/GSM/WCDMA. any help would be nice, I seem to mainly get H+ and sometime switches to 3G.
Using ATT carrier.
Sent from my Nexus 7
Click to expand...
Click to collapse
I'm going to offer the same suggestions: check your APN settings (that seems to be the big one for AT&T) and check your network types.
I assume you've had LTE coverage under other ROMs?
Hey guys, when I connect my phone to my PC I can't see any folders. Anyone else having this?
AOKP 4.2 preview
Sent from my SGH-I747 using xda premium
Everything installs fine,....but the google play store gives me a "no connection" error....but browsing the internet works fine. I followed all the steps exactly.
zap12341 said:
Hey guys, when I connect my phone to my PC I can't see any folders. Anyone else having this?
AOKP 4.2 preview
Sent from my SGH-I747 using xda premium
Click to expand...
Click to collapse
Are no files displayed at all or is it just displaying differently? Once I updated, it moved all my files to the folder/0. Check there and it should display your folders as on 4.1. I believe it has to do with the multiple user functionality.
Sent from my Nexus 7 using xda app-developers app
When I flashed it, it didn't create a /0 for me.
Sent from my SGH-I747 using xda premium
zap12341 said:
When I flashed it, it didn't create a /0 for me.
Sent from my SGH-I747 using xda premium
Click to expand...
Click to collapse
I can't see any folders either. Same ROM.
Sent from my SAMSUNG-SGH-I747 using xda premium
zap12341 said:
Hey guys, when I connect my phone to my PC I can't see any folders. Anyone else having this?
AOKP 4.2 preview
Sent from my SGH-I747 using xda premium
Click to expand...
Click to collapse
Its a preview. Its not supposed to work. The preview I released is basically just a screenshot of what's to come. I haven't even release a full ROM yet.
Emoticons
The emoticons are now implemented in the keyboard, is there a way to flash em over or download em. If anyone else has this issue let me know.
I can't get Portable Wi-Fi hotspot to work?
any ideas, has anyone else tried it?
is there a way to submit bug reports for nightly builds?
no data connection at all now via the radio.(but the phone can receive & make calls) I followed the steps to check it as posted by another user above....but still tryin different modem files.
did you try the fix in the op?
CM10.1 on Bell Galaxy SIII
I installed CM10.1 yesterday. Most of it works flawlessly. Had to uninstall and reinstall some apps (Google Play Magazines) for example. But almost all of them work as is.
I do have a problem with cell data connectivity. I need to reboot a couple of time to make it work. When it does, it works flawlessly. But when it doesn't there's nothing you can do. And it's random. You reboot, it may or may not work. If it doesn't, you reboot until it does. I also didn't have H+. I changed my baseband version and I now have H+.
This very much like a limit condition on init sequence. It was working with CM10 so I guess the components initialization sequence changed a bit for CM10.1.
wujiku said:
did you try the fix in the op?
Click to expand...
Click to collapse
Ya that's what I've been working on. I finally did get it working (for now) with the modem 3rd down on the list.
Does CM10.1 have a LTE icon that appears when LTE is being used, or does it always just say "4G"?
---------- Post added at 06:48 PM ---------- Previous post was at 06:39 PM ----------
ebfortin said:
I installed CM10.1 yesterday. Most of it works flawlessly. Had to uninstall and reinstall some apps (Google Play Magazines) for example. But almost all of them work as is.
I do have a problem with cell data connectivity. I need to reboot a couple of time to make it work. When it does, it works flawlessly. But when it doesn't there's nothing you can do. And it's random. You reboot, it may or may not work. If it doesn't, you reboot until it does. I also didn't have H+. I changed my baseband version and I now have H+.
This very much like a limit condition on init sequence. It was working with CM10 so I guess the components initialization sequence changed a bit for CM10.1.
Click to expand...
Click to collapse
This is getting to be my experience. I just tried a few different modems, and finally got it to work...then I decided to reboot...and it stopped working. A few reboots later, and it still is down for the count. I guess I'll try another modem.
Hey guys,
I recently upgraded my Rogers Galaxy S3 d2att from CM10.1 Nightly 02/12 to CM 10.2 and have no longer been able to get the usual H+ connection. I now have either no letter or an E beside the signal bar. I did the following:
Dirty Flash 10.2 through Recovery Menu
Delete cache, dalvik and data in recovery menu
Couldn't get 3G, 4G or H+ Connection so I dirty flashed 10.1
Installed latest d2att rogers modem, installed latest bootloader, neither worked
Flashed back to CM10.1 Nightly
Can't get previous H+ connection on CM10.1 Nightly
I'm getting the worst headache trying to solve this. I'm more than willing to revert back to stock to try and get this working properly.
Thanks!
UPDATE:
I found out my IMEI was deleted while flashing. Does anybody know how I would get this back?
First off, how did you get cm 10.2
Cerhio;4409stock said:
[*]Dirty Flash 10.2 through Recovery Menu
[*]Delete cache, dalvik and data in recovery menu
[*]Couldn't get 3G, 4G or H+ Connection so I dirty flashed 10.1
[*]Installed latest d2att rogers modem, installed latest bootloader, neither worked
[*]Flashed back to CM10.1 Nightly
[*]Can't get previous H+ connection on CM10.1 Nightly
[/LIST]
I'm getting the worst headache trying to solve this. I'm more than willing to revert back to stock to try and get this working properly.
Thanks!
UPDATE:
I found out my IMEI was deleted while flashing. Does anybody know how I would get this back?
Click to expand...
Click to collapse
Try going back to stock by odin. That should work. And how did you get cm 10.2?? Can you give me the link where you downloaded from. That would be great.
Cerhio said:
Hey guys,
I recently upgraded my Rogers Galaxy S3 d2att from CM10.1 Nightly 02/12 to CM 10.2 and have no longer been able to get the usual H+ connection. I now have either no letter or an E beside the signal bar. I did the following:
Dirty Flash 10.2 through Recovery Menu
Delete cache, dalvik and data in recovery menu
Couldn't get 3G, 4G or H+ Connection so I dirty flashed 10.1
Installed latest d2att rogers modem, installed latest bootloader, neither worked
Flashed back to CM10.1 Nightly
Can't get previous H+ connection on CM10.1 Nightly
I'm getting the worst headache trying to solve this. I'm more than willing to revert back to stock to try and get this working properly.
Thanks!
UPDATE:
I found out my IMEI was deleted while flashing. Does anybody know how I would get this back?
Click to expand...
Click to collapse
Are you sure you don't mean CM 10.1.2? I don't think CM 10.2 is available for the Rogers or AT&T Galaxy S III yet...if it is please link to it.
n_alvarez2007 said:
Are you sure you don't mean CM 10.1.2? I don't think CM 10.2 is available for the Rogers or AT&T Galaxy S III yet...if it is please link to it.
Click to expand...
Click to collapse
Yes sorry, you're absolutely right! I still have service on my phone but I cannot even get 3G signal.
Cerhio said:
Yes sorry, you're absolutely right! I still have service on my phone but I cannot even get 3G signal.
Click to expand...
Click to collapse
1. Check if Access Points are correct
2. Check if you lost your IMEI (normally if you still get service but not mobile data beside edge, your IMEI will show as 0)
3. if the above aren't true, have you try flashing different nightly/stable or different roms?
and if your imei was deleted
you need to inject your imei again
first, take out the battery, beside the battery there should be serial numbers and imei numbers
secondly, you need SGS3 NV Gen and NV item reader & writer OR you can also use QRST though the process is a little more difficult (I don't think i can distribute the files here, and QRST you can google it)
as for SGS3 NV gen and nv item writer, you just need to copy and paste your imei to SGS3 NV Gen and it'll write to a text file, then all you need is to use NV item writer to connect with your phone and upload the file.
oh and you need to revert back to stock rom because the phone needed to be in RM + Modem + something mode lol... which is located in one of the secret menu .... i believe it was *#7284#
pcshano said:
2. Check if you lost your IMEI (normally if you still get service but not mobile data beside edge, your IMEI will show as 0)
Click to expand...
Click to collapse
I did...
I did
I followed your steps. The IMEI was injected successfully but the ERI is still showing 0. How do I fix that?
Or, how do I get it to re-register on the network with the IMEI in place?
Samsung Galaxy S3 (d2att) Poor or no Service
I'm having the same issue - or so it appears. my IMEI was also erased and I restored it using the method described above. That solved the issue of not being able to connect to the network at all, but now my connection last 3 minutes at best. I start off with LTE, then 3g, then g, then no letter at all and through that all, making/receiving calls, sending receiving texts, and even accessing the internet is only doable the first 3 minutes or so. After that, all if gone.
I've gone through the following radios:
I747UCLEM: modem_CWM_I747UCLEM.zip - 19.06 MB - May 22nd, 2012 (original shipped)
I747UCLG1: modem_CWM_I747UCLG1.zip - 19.06 MB - July 1st, 2012
I747UCLH1: modem_CWM_I747UCLH1.zip - 19.40 MB - August 1st, 2012
I747UCLH9: modem_CWM_I747_UCLH9.zip - 18.90 MB - August 9th, 2012
I747UCLI5: modem_CWM_I747UCLI5.zip - 19.51 MB - September 5th, 2012
I747UCDLK3: modem_CWM_I747UCDLK3.zip - 18.42 MB - November 3rd, 2012
I747UCDMG2: modem_CWM_I747UCDMG2.zip - 19.01 MB - July 2nd, 2013
I've tried various CWM versions, ROMs, and even Odined back to stock but still have the same issue. I ruled out the possibility of it being a SIM issue by placing my SIM in another phone. Service worked beautifully as expected. I took a working SIM from another phone and placed it in mine and had the same poor signal issue.
I've tried a good deal of troubleshooting methods and am seemingly stumped. I'm sorry to see that others are having the issue but I'd like to help however I can. the only thing I can say for certain is wrong at the moment is that my Serial Number seems to have been changed and no longer matches what is written on the phone....could that be the issue?
Current Serial number is displayed in about phone as: 1f03dbad
Hopefully, this provides some insight and someone a bit more knowledgeable than myself can help us find a solution.
If you need anything else, let me know and I'll do my best to provide it.
Please help I have the same issue, I have flashed back AT&T official ROM, but no 3G signals and weak phone signals. Did you guys find a solution? How do I check my ERI?
Please help if you have a solution.
triplethreat117 said:
I'm having the same issue - or so it appears. my IMEI was also erased and I restored it using the method described above. That solved the issue of not being able to connect to the network at all, but now my connection last 3 minutes at best. I start off with LTE, then 3g, then g, then no letter at all and through that all, making/receiving calls, sending receiving texts, and even accessing the internet is only doable the first 3 minutes or so. After that, all if gone.
I've gone through the following radios:
I747UCLEM: modem_CWM_I747UCLEM.zip - 19.06 MB - May 22nd, 2012 (original shipped)
I747UCLG1: modem_CWM_I747UCLG1.zip - 19.06 MB - July 1st, 2012
I747UCLH1: modem_CWM_I747UCLH1.zip - 19.40 MB - August 1st, 2012
I747UCLH9: modem_CWM_I747_UCLH9.zip - 18.90 MB - August 9th, 2012
I747UCLI5: modem_CWM_I747UCLI5.zip - 19.51 MB - September 5th, 2012
I747UCDLK3: modem_CWM_I747UCDLK3.zip - 18.42 MB - November 3rd, 2012
I747UCDMG2: modem_CWM_I747UCDMG2.zip - 19.01 MB - July 2nd, 2013
I've tried various CWM versions, ROMs, and even Odined back to stock but still have the same issue. I ruled out the possibility of it being a SIM issue by placing my SIM in another phone. Service worked beautifully as expected. I took a working SIM from another phone and placed it in mine and had the same poor signal issue.
I've tried a good deal of troubleshooting methods and am seemingly stumped. I'm sorry to see that others are having the issue but I'd like to help however I can. the only thing I can say for certain is wrong at the moment is that my Serial Number seems to have been changed and no longer matches what is written on the phone....could that be the issue?
Current Serial number is displayed in about phone as: 1f03dbad
Hopefully, this provides some insight and someone a bit more knowledgeable than myself can help us find a solution.
If you need anything else, let me know and I'll do my best to provide it.
Click to expand...
Click to collapse
I am having the same connectivity issues. I had to restore my IMEI earlier this week after a dirty upgrade, and then restored to several 10.1.x versions and back to 10.2, though this did not help. I did a stock restore and then rooted again, as well as restored 10.1.2 and nothing helped. I also dirty flashed beanstalk latest build, 2 builds of paranoid android and nothing worked.
Sometimes I can get on LTE or HSPA+ for a few minutes after turning data off and on, but this resets. I have also tried several APN settings, the ones provided by cyanogenmod as well as reconfigurations.
I having issues with CM10.1.3 ,I searching and finding this on the Google plus internet page of CM talking about compatibility of our phone with the news CM ROMs:
" To make sure your device is primed and ready for this state, the following lists the bootloaders compatible for each device:
d2att: I747UCDLK3 & I747MVLDLK4"
I have also change the baseband...
Sent from my SAMSUNG-SGH-I747 using XDA Premium 4 mobile app
warweolf said:
I having issues with CM10.1.3 ,I searching and finding this on the Google plus internet page of CM talking about compatibility of our phone with the news CM ROMs:
" To make sure your device is primed and ready for this state, the following lists the bootloaders compatible for each device:
d2att: I747UCDLK3 & I747MVLDLK4"
I have also change the baseband...
Sent from my SAMSUNG-SGH-I747 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
This is irrelevant, the new bootloader was added into the recovery ROM so there is no need to downgrade the bootloader. I did just in case to see if my issue would be fixed but as expected it was not.
I just got a Note 2 SPH-L900 (Sprint) it has a bad ESN for sprint but my intention was to flash it to cricket. I had noticed the same thing before the flash over to Cricket (I was messing with it over wifi etc and I did flash cm10.2 nightly just for the heck of it, then back to stock) but I could not verify service since I am not a Sprint customer. However the issue seems to not be carrier-specific.
When I flash custom ROMs I do not have service. No call, no data, nothing but wifi. The signal bar is empty and I get a big "?" Where the carrier is supposed to be. Also under "status" there is many blank spaces, no phone number, no carrier etc. Upon factory restore (which was done 2 or 3 times to ensure a bad ROM flash was not the culprit) the service icons and settings come back as before and everything works well.
I have tried two separate ROMs that give me the same issue: cyanogenmod 10.2 nightly
Rootbox jelly bean
Anyone know what may be wrong? I do not think this has to do anything with the flash over to cricket, since before it was doing the same thing. Any setting/procedure that I may be missing?
Edit: I did not do anything with kernels. My stock ROM android version is the 4.1.2
BBobby said:
I just got a Note 2 SPH-L900 (Sprint) it has a bad ESN for sprint but my intention was to flash it to cricket. I had noticed the same thing before the flash over to Cricket (I was messing with it over wifi etc and I did flash cm10.2 nightly just for the heck of it, then back to stock) but I could not verify service since I am not a Sprint customer. However the issue seems to not be carrier-specific.
When I flash custom ROMs I do not have service. No call, no data, nothing but wifi. The signal bar is empty and I get a big "?" Where the carrier is supposed to be. Also under "status" there is many blank spaces, no phone number, no carrier etc. Upon factory restore (which was done 2 or 3 times to ensure a bad ROM flash was not the culprit) the service icons and settings come back as before and everything works well.
I have tried two separate ROMs that give me the same issue: cyanogenmod 10.2 nightly
Rootbox jelly bean
Anyone know what may be wrong? I do not think this has to do anything with the flash over to cricket, since before it was doing the same thing. Any setting/procedure that I may be missing?
Edit: I did not do anything with kernels. My stock ROM android version is the 4.1.2
Click to expand...
Click to collapse
Well, i got it working now!!! i did reflash the modem to the latest MC2 version, then installed a custom kernel, Sleshepics the governor 1.7.
Then i reflashed the CM10.2 nightly and i magically have signal and data working.
SO EXCITED!
trying to flash my galaxy note ii sph-l900.. need help
i went to a couple of places and they said it couldnt be done.. it has low signal ... it only works on certain areas..
need help
Well it all depends on your signal. I live in Austin TX and cricket has great service here, with some dead spots out in the country (no big deal). 3g speeds are as fast as Sprint's 4g LTE.
The problem I was having had to do when I was flashing custom ROMs I was lising service.
I updated the modem drivers. It did the trick. I havent list service since and ive flashed like 6 ROMs so far.
Sent from my SPH-L900 using Tapatalk
Hello fellow xda members. Well after searching for a solution for my for nearly a week now i figure i should post the question to see if i can get an answer. I did search around before hand and tried many solutions but to no avail.
Background, I have a sgh-t999 that's apparently unlocked since I've been using a fido sim card in it for several months now. when ever I'm running cm 10.1, I have full network access, texts, mms, 3g data, etc.Note: d2mtr is flashed to my phone and my model number gets changed to sch-r530, baseband: t999vvllh2.
After flashing to cm 10.2 RC1. d2mtr. I get stuck on the metroPcs network with out any way to manually switch network operators because the option in mobile networks is greyed out. Everything seems to work fine in terms of calls but besides being able to receive texts messages i can't send them. The signal bar seems to be empty or greyed out yet it still picks up 3g data. I've vigorously checked my apn settings to no avail. deleted the voice+ apk since I'm not in the US being in Canada and i'm all out of options right now. If i restore back to my previous backup ,everything works fine and i did check to see if I loose my imei number after flash.
I previously tried flashing d2tmo to my device but to no avail, assert errors. It would greatly be appreciated to get a response and thank you in advance for any help.
Edit: It's a sgh-t999v as printed behind the battery. I followed this guide http://forum.xda-developers.com/showthread.php?t=1775616 hence the reason why I'm coming from ICS. Looks like I'll have to reflash using ODIN which i was trying to avoid out of fear of bricking but it seems like my only option now.
kyuubie said:
Hello fellow xda members. Well after searching for a solution for my for nearly a week now i figure i should post the question to see if i can get an answer. I did search around before hand and tried many solutions but to no avail.
Background, I have a sgh-t999 that's apparently unlocked since I've been using a fido sim card in it for several months now. when ever I'm running cm 10.1, I have full network access, texts, mms, 3g data, etc.Note: d2mtr is flashed to my phone and my model number gets changed to sch-r530, baseband: t999vvllh2.
After flashing to cm 10.2 RC1. d2mtr. I get stuck on the metroPcs network with out any way to manually switch network operators because the option in mobile networks is greyed out. Everything seems to work fine in terms of calls but besides being able to receive texts messages i can't send them. The signal bar seems to be empty or greyed out yet it still picks up 3g data. I've vigorously checked my apn settings to no avail. deleted the voice+ apk since I'm not in the US being in Canada and i'm all out of options right now. If i restore back to my previous backup ,everything works fine and i did check to see if I loose my imei number after flash.
I previously tried flashing d2tmo to my device but to no avail, assert errors. It would greatly be appreciated to get a response and thank you in advance for any help.
Click to expand...
Click to collapse
Might not be the right ROM for your phone. Or it could be buggy. I've messed around with a few and finally found a great one that seems to be working well for me. I have the d2ltetmo. I'm running Liquid Smooth ROM with 4.2.2 and TWRP 2500 recovery. The ROM roots your phone as well. Any questions feel free to ask. Hope I can help!:cyclops:
I wouldn't flash D2MTR Rom to D2TMO. Too many differing things. There's a CM for D2TMO too.
Are you sure that's a t999? The baseband looks like the one for the t999v.. And it also looks like you might be on ICS firmware.. What I suggest you do is check the model number of your phone to be sure what model you have, after that update to 4.1.1 or 4.1.2 via Odin but make sure its the firmware for your model. After this flash your custom recovery, and then try flashing cm10.1 for d2tmo.. If your device bootloops after you Odin, enter recovery and do a factory reset.
Edit: check the model number by removing the battery and it will say at the back of the phone.. And the firmwares to flash in odin are in the development thread
Sent from my SGH-T999 using Tapatalk
serio22 said:
Are you sure that's a t999? The baseband looks like the one for the t999v.. And it also looks like you might be on ICS firmware.. What I suggest you do is check the model number of your phone to be sure what model you have, after that update to 4.1.1 or 4.1.2 via Odin but make sure its the firmware for your model. After this flash your custom recovery, and then try flashing cm10.1 for d2tmo.. If your device bootloops after you Odin, enter recovery and do a factory reset.
Edit: check the model number by removing the battery and it will say at the back of the phone.. And the firmwares to flash in odin are in the development thread
Sent from my SGH-T999 using Tapatalk
Click to expand...
Click to collapse
Well after a long process of flashing stock jb then finding a proper method of flashing cwm since i had difficulties with fastboot and went with the dd if-of method using the terminal emulator. I am finally on a stable cm 10.2 rom, d2tmo, where everything seems to be working and intact. Thanks for the advice now i have the long process of restoring my apps and data and what not with titanium backup.
So I flashed CM 10.2 to my D2ATT last friday and was completely happy with it. The snow storms cancelled my weekend plans so I was home with my wifi all weekend. Upon leaving for work this morning, however, I noticed that I was unable to pick up mobile data. I found out through googling that this is a common error with 10.2 so I tried upgrading to a CM11 nightly. For whatever reason my phone doesn't like them and CWM gives an error when trying to install them even if I perform a system wipe.
I tried switching to AOKP and got absolutely 0 service from AT&T as far as cell reception, calls, texts, and mobile data.
I'm back to CM 10.2 right now, and word on the net is that I need a modem file, but I can't seem to find one for my phone. Can anyone get me a link or a fix?
Thanks!
In the SGS III development section there is all the modem files it has it's own thread
Sent from my SGH-I747M using Tapatalk
jimchee said:
In the SGS III development section there is all the modem files it has it's own thread
Sent from my SGH-I747M using Tapatalk
Click to expand...
Click to collapse
I appreciate the response, but I quite frankly have no idea what I'm looking at in any of the three dev forums and can't find the modem file thread. Could you please be a bit more specific?
before trusting on anything
go to your setting-->about and look if your IMEI is still intact
pcshano said:
before trusting on anything
go to your setting-->about and look if your IMEI is still intact
Click to expand...
Click to collapse
I do have a 15 digit IMEI as well as a two digit IMEI SV. I did however notice that it said "mobile network status: disconnected" so I had it search for networks (it found two labeled AT&T and one was a 5 digit number) and auto select the best one. During that process I received and sent a few texts. After that process it said "selected network" but nothing had changed, and it still said I was disconnected.
I had the same problem when I flashed to stock 4.3, I lost T-Mobile service and only could call and text no data! I flashed the modem from here http://forum.xda-developers.com/showpost.php?p=47817339&postcount=23 only download the modem_ and after I flashed and reboot viola! Data working perfectly Hope this helped!!!
Sent from my SAMSUNG-SGH-I747 using xda app-developers app