Hi guys,
I used techfanatic9's DIY for going to Jellybean on my VZW galaxy nexus and it worked but I had no mobile network.
After a few attempts they referred me to their going back to stock which used ODIN.
Anyway, reflashing back to stock failed in Odin and after I took the battery out and out it back in (with the cable connected) i could no longer get to download mode or recovery (I was using clockwork mod recovery).
Now everytime I turn the phone on it has a phone a yellow exclamation point and a monitor and I can't get to recovery or download mode.
Can anyone help me at least get to recovery mode again? Odin still recognizes my phone (drivers good) but it always fails to flash back to stock. I just got this phone not too long ago and I'm kind of devastated =(
corning84 said:
Hi guys,
I used techfanatic9's DIY for going to Jellybean on my VZW galaxy nexus and it worked but I had no mobile network.
After a few attempts they referred me to their going back to stock which used ODIN.
Anyway, reflashing back to stock failed in Odin and after I took the battery out and out it back in (with the cable connected) i could no longer get to download mode or recovery (I was using clockwork mod recovery).
Now everytime I turn the phone on it has a phone a yellow exclamation point and a monitor and I can't get to recovery or download mode.
Can anyone help me at least get to recovery mode again? Odin still recognizes my phone (drivers good) but it always fails to flash back to stock. I just got this phone not too long ago and I'm kind of devastated =(
Click to expand...
Click to collapse
Follow up.. Did a lot of self educating over 3 days.
I lost recovery. I made a jig using some resistors from radio shack and cutting up an unused usb cable.
Got download mode back and used Odin (which is a very bad tool from my research but also can be good) + a 4.0.2 image and a phone file and restored my soft brick back to stock.
Hey, so my note 2 (sgh-i317m variant) running 4.3 is stuck on the samsung screen and I cannot boot into recovery (it just stays at the samsung screen). What I believe caused this is the fact that I originally had it rooted, but flashed back to stock via odin to update to 4.3. Then I proceeded to re root it via odin and the cf auto root, however I forgot to factory reset before doing this. Now its stuck on the samsung screen and I cannot even get it into recovery mode. I can get it into download mode but whenever I try reflashing the stock rom (I have two different ones) neither of them work and Odin just displays "fail". I really dont know what else to do, hoping someone will know, thanks in advance.
Friend, try Google for KIES3. After installation under the Menu bar..look into something recoveries..
There you'll need to enter your model and serial no.
Boot your hp to DOWNLOAD MODE and plug to your usb. Then let KIES do its work.
Hope it helps
53N53L355 said:
Friend, try Google for KIES3. After installation under the Menu bar..look into something recoveries..
There you'll need to enter your model and serial no.
Boot your hp to DOWNLOAD MODE and plug to your usb. Then let KIES do its work.
Hope it helps
Click to expand...
Click to collapse
That didnt work
Mbrar15 said:
Hey, so my note 2 (sgh-i317m variant) running 4.3 is stuck on the samsung screen and I cannot boot into recovery (it just stays at the samsung screen). What I believe caused this is the fact that I originally had it rooted, but flashed back to stock via odin to update to 4.3. Then I proceeded to re root it via odin and the cf auto root, however I forgot to factory reset before doing this. Now its stuck on the samsung screen and I cannot even get it into recovery mode. I can get it into download mode but whenever I try reflashing the stock rom (I have two different ones) neither of them work and Odin just displays "fail". I really dont know what else to do, hoping someone will know, thanks in advance.
Click to expand...
Click to collapse
POST the complete ODIN log here.
...
Mbrar15 said:
Hey, so my note 2 (sgh-i317m variant) running 4.3 is stuck on the samsung screen and I cannot boot into recovery (it just stays at the samsung screen). What I believe caused this is the fact that I originally had it rooted, but flashed back to stock via odin to update to 4.3. Then I proceeded to re root it via odin and the cf auto root, however I forgot to factory reset before doing this. Now its stuck on the samsung screen and I cannot even get it into recovery mode. I can get it into download mode but whenever I try reflashing the stock rom (I have two different ones) neither of them work and Odin just displays "fail". I really dont know what else to do, hoping someone will know, thanks in advance.
Click to expand...
Click to collapse
Did you end up figuring it out?
Hi guys I just bought a SGH-I747 AT&T and the issue with it is it goes into Download mode just fine, works with Odin 3.7 loads a stock rom and then it sais reset but the phone doesn't reset just goes to black screen and then Odin sais Pass. I press the power button and Samsung appers and vibrates and goes back to black. When I try Recovery mode it show the blue writing on the left upper and the Samsung and then it goes to black screen. I put two different stock roms and same story. Kies won't recognize it and I installed recovery-clockwork-touch-6.0.4.3-d2att.tar to try to get into recovery mode and of course no luck. Don't know the history on this, so if anyone could help I would really appreciate it. Thanks in advance.
gica69 said:
Hi guys I just bought a SGH-I747 AT&T and the issue with it is it goes into Download mode just fine, works with Odin 3.7 loads a stock rom and then it sais reset but the phone doesn't reset just goes to black screen and then Odin sais Pass. I press the power button and Samsung appers and vibrates and goes back to black. When I try Recovery mode it show the blue writing on the left upper and the Samsung and then it goes to black screen. I put two different stock roms and same story. Kies won't recognize it and I installed recovery-clockwork-touch-6.0.4.3-d2att.tar to try to get into recovery mode and of course no luck. Don't know the history on this, so if anyone could help I would really appreciate it. Thanks in advance.
Click to expand...
Click to collapse
I found out that the phone had 4.1.1 on it and the guy tried to flash 4.2.2 and upon doing the odin mode flashing odin gave Firmware upgrade encountered an issue Please select recovery mode in Kies & try again So these are just some helpful facts for anyone who has gone through it. Thanks in advance for any help
gica69 said:
I found out that the phone had 4.11 on it and the guy tried to flash 4.22 and upon doing the odin mode flashing odin gave Firmware upgrade encountered an issue Please select recovery mode in Kies & try again So these are just some helpful facts for anyone who has gone through it. Thanks in advance for any help
Click to expand...
Click to collapse
What firmware were you trying to flash via Odin and are you sure the seller didn't previously flash (or try to flash) the 4.3 on it? If it wasn't higher than 4.3, then you may try recovery via Kies as follows ....
Install and launch Samsung Kies on your PC (not Kies 3). Open the Tools menu and select Firmware Upgrade and Initialization
Do not connect your phone to your PC yet. Remove the battery cover and record device info written in the battery compartment
In Kies, enter your phone model (SGH-I747)
Enter the phone serial number and click OK to all the security questions. Follow all the instructions on Kies
Connect the phone when prompted and follow the rest of the instructions
Wait for firmware upgrade to complete
Good luck!
If this doesn't work, then you may try flashing the 4.1.1 stock image via Odin. Look for the correct stock image via the following thread ...
http://forum.xda-developers.com/showthread.php?t=1739426
The one you want for Samsung Galaxy S3 AT&T (4.1.1) is I747UCDLK3
PLEASE don't try any of the above if you were already on the 4.3 bootloader as things will only get worse.
Larry2999 said:
What firmware were you trying to flash via Odin and are you sure the seller didn't previously flash (or try to flash) the 4.3 on it? If it wasn't higher than 4.3, then you may try recovery via Kies as follows ....
Install and launch Samsung Kies on your PC (not Kies 3). Open the Tools menu and select Firmware Upgrade and Initialization
Do not connect your phone to your PC yet. Remove the battery cover and record device info written in the battery compartment
In Kies, enter your phone model (SGH-I747)
Enter the phone serial number and click OK to all the security questions. Follow all the instructions on Kies
Connect the phone when prompted and follow the rest of the instructions
Wait for firmware upgrade to complete
Good luck!
If this doesn't work, then you may try flashing the 4.1.1 stock image via Odin. Look for the correct stock image via the following thread ...
http://forum.xda-developers.com/showthread.php?t=1739426
The one you want for Samsung Galaxy S3 AT&T (4.1.1) is I747UCDLK3PLEASE don't try any of the above if you were already on the 4.3 bootloader as things will only get worse.
Click to expand...
Click to collapse
I have already tried the I747UCDLK3 not from the link you gave me though. I did notice that the one you mentioned is a rooted stock do you think I should still do it? The rom flashes fine no errors in Odin but when it sais RESET the phone turns off the download mode and vibrates once then goes black then later Odin sais Pass but I cannot start it it just bootloops and vibrates and it stays that way As far as the Kies procedure you gave me don't I have to be in recovery mode for it to see the phone? I cannot get to that mode just download mode. Let me know thanks for your help
gica69 said:
I have already tried the I747UCDLK3 not from the link you gave me though. I did notice that the one you mentioned is a rooted stock do you think I should still do it? The rom flashes fine no errors in Odin but when it sais RESET the phone turns off the download mode and vibrates once then goes black then later Odin sais Pass but I cannot start it it just bootloops and vibrates and it stays that way As far as the Kies procedure you gave me don't I have to be in recovery mode for it to see the phone? I cannot get to that mode just download mode. Let me know thanks for your help
Click to expand...
Click to collapse
If you were successful in flashing via Odin, I would have suggested you try doing a hard wipe/reset in recovery. However, you said you can't get to recovery mode so this may not work. What happens when you try booting into recovery mode?
For Kies, you wouldn't have to be in recovery mode for the firmware restore to happen. Normally, you would have to connect your (powered-on) phone to your PC for it to be recognized by Kies. However, as you can't power on, we are forcing Kies to prepare the specific required firmware for your device by manually entering in the device information. Thus, when the phone is connected, you have firmware ready to make it work.
It may also be that the firmware you downloaded and flashed via Odin may not be the correct or full version. There are so many sources of "stock" firmware these days that one can never be too sure. You may go to Sammobile.com to download the stock firmware and compare the size of the extracted file to the one you used. The odin flashable tar.md5 file should be about 1.1Gb in size.
Larry2999 said:
If you were successful in flashing via Odin, I would have suggested you try doing a hard wipe/reset in recovery. However, you said you can't get to recovery mode so this may not work. What happens when you try booting into recovery mode?
For Kies, you wouldn't have to be in recovery mode for the firmware restore to happen. Normally, you would have to connect your (powered-on) phone to your PC for it to be recognized by Kies. However, as you can't power on, we are forcing Kies to prepare the specific required firmware for your device by manually entering in the device information. Thus, when the phone is connected, you have firmware ready to make it work.
It may also be that the firmware you downloaded and flashed via Odin may not be the correct or full version. There are so many sources of "stock" firmware these days that one can never be too sure. You may go to Sammobile.com to download the stock firmware and compare the size of the extracted file to the one you used. The odin flashable tar.md5 file should be about 1.1Gb in size.
Click to expand...
Click to collapse
When I go in recovery it shows blue writing in left upper corner and Samsung logo and then black screen. I think I did use the Sammobile firmware at 1.1. My clock in download mode shows 6. I don't think that would affect it though. Could it be that Odin doesn't really write the firmware that's why flashing doesn't change anything? I don't think the jig would do anything maybe sending it for a jtag reflash is the trick.
I am lost for now. If you guys can think of anything new let me know and thanks again.
gica69 said:
When I go in recovery it shows blue writing in left upper corner and Samsung logo and then black screen. I think I did use the Sammobile firmware at 1.1. My clock in download mode shows 6. I don't think that would affect it though. Could it be that Odin doesn't really write the firmware that's why flashing doesn't change anything? I don't think the jig would do anything maybe sending it for a jtag reflash is the trick.
I am lost for now. If you guys can think of anything new let me know and thanks again.
Click to expand...
Click to collapse
You didn't mention if you tried the Kies option. I had a similar problem once when upgrade to 4.1.1 via Kies failed during the process and that was how I was able to recover. However, since you bought this from the secondary market, there is no way of telling for certain what the previous owner did wrong which would have been useful for recovery options.
One of the nice things about Odin is that you usually know the results immediately. If it says Pass, therefore, that's likely what it means. So Odin did flash something. But what did it flash? The counter you saw in download mode shows how many custom system installations there have been and 6 does show there has been some previous heavy tinkering with the phone. As you are still able to get into download modes, I would suggest you try flashing custom recovery (TWRP or CWM) via Odin. If this works and you are able to get into recovery mode, you may then try doing a hard wipe/reset via recovery. You may also try flashing the other (rooted) 4.1.1 file via Odin. At this stage, you really have nothing to lose in trying all options. I guess if you can get into recovery mode, the problem is almost solved as this leaves plenty of options.
A jig wouldn't help as that only gets you to download mode which, for now, you don't have a problem with. JTag should always be a last resort option only. Let me know how far it goes and good luck!
When flashing in Odin, did you check auto reboot? If you did, try flashing again but uncheck auto-reboot. When you see Reset in the status windows, disconnect the USB cable, pull out the battery, wait a few seconds until the phone completely shuts down, put back in the battery, get into recovery, wipe cache, do a factory reset, and reboot.
audit13 said:
When flashing in Odin, did you check auto reboot? If you did, try flashing again but uncheck auto-reboot. When you see Reset in the status windows, disconnect the USB cable, pull out the battery, wait a few seconds until the phone completely shuts down, put back in the battery, get into recovery, wipe cache, do a factory reset, and reboot.
Click to expand...
Click to collapse
This damn phone is starting to annoy me. I can still get into download mode but my phone gets usb device not recognized now. I have access to another I747 phone so my question is if I have access to the pit file from that phone can anything be done with the Debrick utility and a SD card with only download mode access? Thanks in advance.
Go into download and let us know what is shown on the screen.
audit13 said:
Go into download and let us know what is shown on the screen.
Click to expand...
Click to collapse
Odin Mode
Product Name: SGH-I747
Custom Binary Downloads: Yes (6 Counts)
Current Binary: Samsung Official
System Status: Official
Qualcomm Secure Boot: Enable
Green Android Icon Downloading...
Do not turn off target!!!
OK I plugged the USB in and out a few times and it allows to write every few tries. Back to my question can I do something in download mode if I have another i747 that I can copy stuff from? I also tried the suggestion to uncheck auto-reset pull the usb cable then the battery and try to go to recovery but it doesn't.Any suggestions are welcomed.
Try flashing a stock 4.1.1 rom from sammobile using Odin. Do not check auto reboot. When you see reset in the status window, disconnect the usb cable, pull the battery, replace the battery, boot into recovery, and wipe. I have done this numerous times on my i747m after flashing custom ROMs.
audit13 said:
Try flashing a stock 4.1.1 rom from sammobile using Odin. Do not check auto reboot. When you see reset in the status window, disconnect the usb cable, pull the battery, replace the battery, boot into recovery, and wipe. I have done this numerous times on my i747m after flashing custom ROMs.
Click to expand...
Click to collapse
I will try it again I think I already did but when I put the battery back and click the Vol+ Home Power I get the blue writing and then black screen. Should I wait like 10 min on the black screen or it should be quick. Thanks
Keep holding the buttons until the blue writing disappears and the green android appears with the green progress bar.
audit13 said:
Keep holding the buttons until the blue writing disappears and the green android appears with the green progress bar.
Click to expand...
Click to collapse
Is there an unbrick.img for 4.1.1 or 4.1.2 I noticed that there are files for 4.3 that allow you to go in recovery and erase stuff reinstall. Let me know cause I sure couldn't find it.
If u can get it into download mode u are never ever hard bricked my friend...take it from a guy who had to dust off his old galaxy sll last weekend & still can't get into d/l mode on my s3 after a week & even with a jig lol
Sent from my SGH-T989 using xda app-developers app
gica69 said:
Is there an unbrick.img for 4.1.1 or 4.1.2 I noticed that there are files for 4.3 that allow you to go in recovery and erase stuff reinstall. Let me know cause I sure couldn't find it.
Click to expand...
Click to collapse
The unbricking image only helps you get into download mode from where you can work your way up the rest of the food chain. As you can already get into download mode without difficulties, I doubt if that's what you really need. You are also able to flash ROMs successfully in download mode via Odin so you've gone far up on the food chain already. Perhaps you are not doing the recovery thing correctly enough. Like Audit said, you need to continue holding down the Volume Up and Menu buttons whilst releasing the Power button after you see the first flash until the recovery menu appears and then do a hard wipe/reset.
Perhaps you could also try flashing TWRP via Odin if CWM isn't working.
Larry2999 said:
The unbricking image only helps you get into download mode from where you can work your way up the rest of the food chain. As you can already get into download mode without difficulties, I doubt if that's what you really need. You are also able to flash ROMs successfully in download mode via Odin so you've gone far up on the food chain already. Perhaps you are not doing the recovery thing correctly enough. Like Audit said, you need to continue holding down the Volume Up and Menu buttons whilst releasing the Power button after you see the first flash until the recovery menu appears and then do a hard wipe/reset.
Perhaps you could also try flashing TWRP via Odin if CWM isn't working.
Click to expand...
Click to collapse
I already tried holding the Home and Volume up buttons for 4-5 minutes at which point my fingers got a bit tired. The reason I wanted the unbrick.img is that I am now having issues with the computer recognizing the device in usb. I plugged and unplugged so many times that it no longer works that way so I wanted to do it via sd card. The unbrick.img gets you in recovery mode and download mode as it allows you to boot from the card not from the internal HD. But the only ones I have seen are for the 4.3 issues. And I tried It but did not put my device in recovery.
gica69 said:
I already tried holding the Home and Volume up buttons for 4-5 minutes at which point my fingers got a bit tired. The reason I wanted the unbrick.img is that I am now having issues with the computer recognizing the device in usb. I plugged and unplugged so many times that it no longer works that way so I wanted to do it via sd card. The unbrick.img gets you in recovery mode and download mode as it allows you to boot from the card not from the internal HD. But the only ones I have seen are for the 4.3 issues. And I tried It but did not put my device in recovery.
Click to expand...
Click to collapse
I couldn't find one either although you may be able to create yours using the command line posted in the thread below ...
http://forum.xda-developers.com/showthread.php?t=2549068
You may also try using a jig to get back into download mode. Have you, however, considered exercising any buyer protection options you have on the phone since, it would appear, the guy sold you a lemon?