I've been trying for the past two days to flash CM9 (cm-9.1.0-anzu) on my Arc S (LT18i), but with no success, as each time I try to install it through Recovery mode (which I installed using RecoverX, as xparts and CWM Rom Manager don't seem to work) I run into the Status 7 error.
I read all I could here about this error 7, but nothing seems to work to me (reinstalling this or that kernel, et cetera). And each time I have to flash the original ftf for the stock GB (lt18i_62.ftf). My bootloader is unlocked.
This is basically my procedure, and obviously something must be dead wrong with it:
1) After some failed attempt, I flash the stock ROM back via Flashtool.
>Now I'm on this setup:
Android: 2.3.4;
Kernel: 2.6.32.9-perf [email protected] # 1
Build: 4.0.2.A.0.62
2) I root succesfully via ERoot.
3) I install CWM through RecoverX.
4) I boot it to recovery, wipe data, cache, delvik, etc, and attempt to flash any custom rom (I've tried CM9, CM7 and some "PAC_iyokan_JB_4.1.2-v19.3.0"), all of which give me the Status 7 error.
What gives? Should I be flashing a specific kernel somewhere or something?
Thanks in advance.
Don't wipe /system, this causes the issue, as CM builds are made to check, that the correct firmware is being installed the phone (not the wrong phone model ROM).
Also, CM9 requires custom kernel, so instead of rooting and installing recovery, flash the custom kernel and use it's built-in recovery.
Which wipes should I do, then? None? I'm not sure which wipe wipes /system.
Which custom kernel is that? Surely not the boot.img included in cm-9.1.0-anzu.zip, right?
And this custom kernel, should I flash it using flashmode or fastboot mode?
zynphull said:
Which wipes should I do, then? None? I'm not sure which wipe wipes /system.
Which custom kernel is that? Surely not the boot.img included in cm-9.1.0-anzu.zip, right?
And this custom kernel, should I flash it using flashmode or fastboot mode?
Click to expand...
Click to collapse
Wipes - Same as earlier, but do not choose format /system.
boot.img is the custom kernel file. And it can only be installed in fastboot mode.
Someguyfromhell said:
Wipes - Same as earlier, but do not choose format /system.
boot.img is the custom kernel file. And it can only be installed in fastboot mode.
Click to expand...
Click to collapse
I don't think I was wiping /system (I'm not even sure how that is done), but installing the custom kernel and then installing CM through its own recovery did the trick, thanks a lot!
Though CM9 is pretty old, so I now itch to try CM10... Is this procedure (installing the boot.img kernel, running its recovery, flashing ROM+gapps) the same for all CM ROMs, or all LT18i ROMs, for that matter?
Thanks again!
zynphull said:
I don't think I was wiping /system (I'm not even sure how that is done), but installing the custom kernel and then installing CM through its own recovery did the trick, thanks a lot!
Though CM9 is pretty old, so I now itch to try CM10... Is this procedure (installing the boot.img kernel, running its recovery, flashing ROM+gapps) the same for all CM ROMs, or all LT18i ROMs, for that matter?
Thanks again!
Click to expand...
Click to collapse
Yes it's pretty much the same... And always use the kernel inside zip...
Sent from my Xperia Neo V using Tapatalk 2
Related
Ive got this message in cwm when was restoring (jj's hybrid for locked bootloader): no app2sd partition found, any ideas?
Locked Bootloader Arc S.
When i want to format sd-ext --> same message.
Prince
Bump
Prince
That means that CWM didn't find a second partition in your SD card used by Link2SD.
Is it working fine, JJ ROM?
Im just wondering if i can flash it with this 'error'.
Prince
I presume jj's rom has app2ext built in, but it shouldn't affect the rom. But check on the rom thread.
sinkster©
I was asking, but no1 replied.
Prince
It will work. That "error" is just a check if a sd partition exists to make use of. Wont affect sysyem if missing.
Typed down from the sky with sexy LT15i
Thx then xd
Prince
hints that migh be helpful to prevent trouble when flashing custom roms & kernels
hi there,
i'm not entirely sure if this will help you but generally speaking i came made a few observations about the fact that some people, mostly repeatingly the same users, encounter problems with their custom roms and/or flashing them, while others don't, albeit they are using the same devices.
i myself use 3 different devices, all rooted and running on pac 4.3, always latest nightly, as there are GT-N7100 - GT-I9100 - Nexus 4
not to the point
a) other than most other users i usually clean cache and dalvik cache as well before and after flashing the new rom and/or new nightly
and never encountrer any problems except those which everybody, using the same rom and nightly encounters.
b) whenever i flash an totally different rom and/or upgrade and/or downgrade to another level of android os, i.e. from 4.2.2 to 4.3, i perform
a clean install, including not only a factory reset, but as well a format sd-card, format cache and format system etc., again i cannot proof
which of these steps make a or the differnce but however, i never have problems others than thosw which everyone has with a version.
c) when using cusome kernels and due to the fact that some roms come with a kernel included, as well as with a custom recovery included,
it is strongly recommended not to forget to flas the kernel again after each flashing the new rom. one good example ist dorimanx kernel
for GT-I9100 which will not boot into recovery and reluctantly boot at all after a new flash of a pac nightly without reflashing the kernel.
d) try to fix permissions on reboot instead of doing it from recovery. one reason is that not every recovery has this option and further i
found that when fixing permissions before the first boot after flashing a new rom, there might be bootloops, albeit i cannot explain exactly
why that should, but however, sometimes it's better to be on the safe sid.
e) try to run whether the lastes version of custom recovery for your device, and or the use the included custom recovery of the rom or the
kernel. this again is one thing that can help to avoid some unexpected and hard to explain bootproblems and/or fc's etc.
hope that i could give you some new ideas how to avoid trouble while using custom roms and other hacks
Pulkit_i21 said:
hi ...i need your help...i am also using xperia arc s (2.3.4), rooted. i tried to install ultimate HD 5 around 6-7 times from different ways, all instructions on internet i followed, in my arc but always it stuck on sony ericson logo and i need to flash it again and again....please help me..why i a, not able to install ultimate hd ..waiting for your reply thanks
Click to expand...
Click to collapse
You must use ICS kernel, either unlock bootloader and install custom ICS kernel, or first install/update to stock ICS and then follow the same method.
i already did 6 times
i already tried 6-7 time to install custom rom when it stuck on sony logo i flashed it with orignal stock rom and tried again but every times same problem arise. now i am not understanding where i missed
Someguyfromhell said:
You must use ICS kernel, either unlock bootloader and install custom ICS kernel, or first install/update to stock ICS and then follow the same method.
Click to expand...
Click to collapse
Pulkit_i21 said:
i already tried 6-7 time to install custom rom when it stuck on sony logo i flashed it with orignal stock rom and tried again but every times same problem arise. now i am not understanding where i missed
Click to expand...
Click to collapse
Kernel. You must use appropriate kernel!
Already tried
i already tried flashing kernel too.....and also in ultimate HD there are option of instaling with locked boot loader.................................i just want to install ultimate HD..........
Someguyfromhell said:
Kernel. You must use appropriate kernel!
Click to expand...
Click to collapse
Pulkit_i21 said:
i already tried flashing kernel too.....and also in ultimate HD there are option of instaling with locked boot loader.................................i just want to install ultimate HD..........
Click to expand...
Click to collapse
Did you install full ICS firmware with kernel prior installing Ultimate HD ROM?
yes
yes i did around 6 times after bootloot i goot in my androing so i flash 2.3.4 gingerbread ftf file again in it
Someguyfromhell said:
Did you install full ICS firmware with kernel prior installing Ultimate HD ROM?
Click to expand...
Click to collapse
Pulkit_i21 said:
yes i did around 6 times after bootloot i goot in my androing so i flash 2.3.4 gingerbread ftf file again in it
Click to expand...
Click to collapse
First install stock ICS firmware, Android 4.0.4 (4.1.B.0.587 or 4.1.B.0.431), and then install the custom ROM. Did you do it so? Can you write the file, which you used?
no..i flashed only base version 4.0.2.A
i always flash "LT18i_4.0.2.A.0.58(2.3.4)_HK" after every bootloop, i not tried to flash 4.1.B.587....few month before tried it to flash but i think it is not able to flash because of system partition is is less because of 4.0.2.................well benifit of installing upgraded rom "4.0.4 (4.1.B.0.587 or 4.1.B.0.431)" and are you sure after that i will able to install it..?
Someguyfromhell said:
First install stock ICS firmware, Android 4.0.4 (4.1.B.0.587 or 4.1.B.0.431), and then install the custom ROM. Did you do it so? Can you write the file, which you used?
Click to expand...
Click to collapse
My friend is currently running Arconium ICS on his Xperia, and now when I tried to install CM9 (Did full wipe > install CM > install gapps in CWM) it just gets stuck at the boot logo (SONY). After recovering the backup of Arconium in CWM it boots up fine again.
Since the boot logo didn't change, I'm thinking CM9 maybe didn't install a new kernel or something? Is there something I can do to make sure that CM9 fits as well as possible? If kernel switching is on the table I'd like to be able to do this from CWM.
Thank you!
bajsmumsaren said:
My friend is currently running Arconium ICS on his Xperia, and now when I tried to install CM9 (Did full wipe > install CM > install gapps in CWM) it just gets stuck at the boot logo (SONY). After recovering the backup of Arconium in CWM it boots up fine again.
Since the boot logo didn't change, I'm thinking CM9 maybe didn't install a new kernel or something? Is there something I can do to make sure that CM9 fits as well as possible? If kernel switching is on the table I'd like to be able to do this from CWM.
Thank you!
Click to expand...
Click to collapse
you must install the kernel "boot.img" through flashtool
is inside the zip file
krattos said:
you must install the kernel "boot.img" through flashtool
is inside the zip file
Click to expand...
Click to collapse
Do I have to do this via flashtool? No way to do it from inside CWM? Please excuse if this is a stupid question, I'm not still a 100 % sure what boot.img, recovery, kernel and all these are and how they fit together.
bajsmumsaren said:
Do I have to do this via flashtool? No way to do it from inside CWM? Please excuse if this is a stupid question, I'm not still a 100 % sure what boot.img, recovery, kernel and all these are and how they fit together.
Click to expand...
Click to collapse
Yes, through the FlashTool is safer.
For all your doubts see this link, is a little extended but very complete.
http://forum.xda-developers.com/showthread.php?t=1133650
bajsmumsaren said:
Do I have to do this via flashtool? No way to do it from inside CWM? Please excuse if this is a stupid question, I'm not still a 100 % sure what boot.img, recovery, kernel and all these are and how they fit together.
Click to expand...
Click to collapse
Boot.img is the kernel in a compiled file, which needs to be installed via fastboot. Flashtool includes fastboot aswell, so you can install the kernel(boot.img) using it.
Recovery is a certain 'program' used to install custom stuff, make full backups(Nandroid backup) and restore them, wipe/format partitions and some other stuff. Recovery can be included already inside the kernel, but there is also possibility to install it on /system partition for those who can't unlock bootloader and/or install custom kernel.
My recommendation - Don't do it if you don't understand anything. You should go and learn about the whole Android first, get yourself familiar with how to recover the phone(install stock firmware etc), what are the terms that we use, what is what etc, then come back. Else...you might get yourself a nice (temporary) brick and then you have another problem, how to get back the phone.
bajsmumsaren said:
My friend is currently running Arconium ICS on his Xperia, and now when I tried to install CM9 (Did full wipe > install CM > install gapps in CWM) it just gets stuck at the boot logo (SONY). After recovering the backup of Arconium in CWM it boots up fine again.
Since the boot logo didn't change, I'm thinking CM9 maybe didn't install a new kernel or something? Is there something I can do to make sure that CM9 fits as well as possible? If kernel switching is on the table I'd like to be able to do this from CWM.
Thank you!
Click to expand...
Click to collapse
Obviously you didnt flash the kernel..and before doing that u need to make sure if ur bootloader is unlocked..if it is unlocked then only you can proceed with flashing the kernel and then installing the ROM.
Same Here!!
but Nothin seems to b workin for me!! Ive Done everything as per da instructions!
I flashed the boot.img file which i unzipped from the cm9 nozomi.zip file!!
I formatted the data, the cache and the dalvik cache and then installed the cm9 and gapps files as well and then when i reboot my device from the recovery menu it just gets stuck at the boot screen of free xperia!!
(
pleasehelp!!
Assistere said:
Same Here!!
but Nothin seems to b workin for me!! Ive Done everything as per da instructions!
I flashed the boot.img file which i unzipped from the cm9 nozomi.zip file!!
I formatted the data, the cache and the dalvik cache and then installed the cm9 and gapps files as well and then when i reboot my device from the recovery menu it just gets stuck at the boot screen of free xperia!!
(
pleasehelp!!
Click to expand...
Click to collapse
Dude, nozomi is only for Xperia S device. You installed the wrong ROM!
Go check the supported devices list to find your device's codename.
Someguyfromhell said:
Dude, nozomi is only for Xperia S device. You installed the wrong ROM!
Go check the supported devices list to find your device's codename.
Click to expand...
Click to collapse
Dude mine is Xperia s is only!!
sorry i frgt to mention bout my phone earlier!!!
Assistere said:
Dude mine is Xperia s is only!!
sorry i frgt to mention bout my phone earlier!!!
Click to expand...
Click to collapse
Then you are at wrong forum.
Hey guys,
I'm new to the Xperia Arc development and need some help with installing a custom rom. I've done quite a bit of reading but still can't figure out what is wrong and why it's simply not working.
So from what I gathered the steps to ensure a successful flash are:
Firstly flash a stock rom via flashtool ie LT18i_4.1.B.0.587.ftf
flash LT18i_4.1.A.0.562_Kernel > root the device > flash back to LT15a_4.1.B.0.587_Kernel
Then now that the device is rooted, I need to install a recovery such as CWM via RecoverX
So, so far so good as I can access CWM, stock rom works fine as well
So then next step is to unlock the bootloader
pretty sure this worked, as when i tried to unlock it again, it said it failed as it was already unlocked
Now flash a custom kernel, in this case i flashed the 146 FXP CM kernel
This also seemed successful as I was presented with a custom splash screen
So then after custom kernel is installed I enter recovery, wipe the cache and reset factory settings, format the data system and cache as well as wiping the dalvik and battery stats.
After, I installed the custom rom zip file, in this case it was aokp_anzu-ota-eng.kxp_build5 and then google apps and then reboot.
So my problems begin here.
My phone seems to be stuck in the boot process (sometimes), on the "initiating swagger" splash screen and it goes crazy. I've tried flashing this rom with other kernels (fusion 3.9) and sometimes it actually loads up into the rom. But the rom is extremely laggy, applications freeze and close and the wifi never works
So my question is, is there any steps or procedures that I am missing, not doing right or in the correct order?
I don't think it's any hardware issues as wifi works in the stock rom, and it's fairly smooth and fluid.
Also, is there a better way to flash roms so that I don't need to do this entire process of flashing a stock rom, rooting, unlocking bootloader, installing recovery every time I want to flash a new rom? And when I flash a custom kernel first, then flash a custom rom that has a kernel inbuilt (cm10) does the custom rom's kernel replace the one i just flashed, reason for asking is that the instructions say to flash the custom kernels and then the roms, but yeh just hasn't been working for me so not really sure how to do what.
I'd really appreciated any help or insight!
Thanks
http://forum.xda-developers.com/showthread.php?p=18445331#post18445331
XperienceD said:
http://forum.xda-developers.com/showthread.php?p=18445331#post18445331
Click to expand...
Click to collapse
Thanks! I've read your guide (what I based my flashing on) and it seems consistent with what I have done, on the surface of it anyway. If you think I missed or overlooked something, would it be possible to point it out?
If your boot loader is unlocked it's as simple as this...
1. Flash kernel
2. Wipe cache etc
3. Install ROM
...I always reboot before installing anything else as I've found it can break the installation of the ROM.
XperienceD said:
If your boot loader is unlocked it's as simple as this...
1. Flash kernel
2. Wipe cache etc
3. Install ROM
...I always reboot before installing anything else as I've found it can break the installation of the ROM.
Click to expand...
Click to collapse
As ExpirienceD says,just one more thing flash kernel modules if you need to.
So:
1.Flash kernel
2.Full wipe data/cach...etc...
3.Flash ROM
4.Flash kernel modules
Sent from my LT15i using xda premium
Hello again guys, I installed LuPuS v8 JB Kernel on my phone (I had 4.0.2.A.0.58 Enhanced Firmware (Gingerbread) installed) then I went to CWM to flash the .zip with the wifi modules and G.Apps but when I rebooted I got a bootloop. what I have to do to correctly install it? Please guide me since I'm kinda newbie to this of unlocked bootloaders and kernels :/ (I'm trying to install PACman rom and followed the FAQ guide but...)
EDIT: Forgot to add, my PLAY is an r800a(i) GSM btw, I have to take off the SDcard to enter to the Kernel menu, idk if this is normal
xkeita said:
Hello again guys, I installed LuPuS v8 JB Kernel on my phone (I had 4.0.2.A.0.58 Enhanced Firmware (Gingerbread) installed) then I went to CWM to flash the .zip with the wifi modules and G.Apps but when I rebooted I got a bootloop. what I have to do to correctly install it? Please guide me since I'm kinda newbie to this of unlocked bootloaders and kernels :/ (I'm trying to install PACman rom and followed the FAQ guide but...)
EDIT: Forgot to add, my PLAY is an r800a(i) GSM btw, I have to take off the SDcard to enter to the Kernel menu, idk if this is normal
Click to expand...
Click to collapse
After you flash the Rom reboot the phone and just let it fully boot. After that you can go back to CWM and flash the WiFi modules and other add-ons
You need to boot into the kernel's recovery and set it to jb mode or ics depending on your rom. Then make sure your rom and gapps don't exceed the system partition size, which it most likely did if you flashed the full gapps package as well.
The default recovery for the lupus jb kernel is TWRP, if you load into another CWM recovery it most likely did not flash to the correct partition arrangement that lupus kernel use therefore the rom can't boot.
Sent from XDA app
Sounds like you didn't wipe data
So go into cwm and wipe cache,data,delvick and try rebooting then
sent from my Sony Ericsson Xperia Play™(r800x) Running Slimbean 3.0 using Tapatalk 2™
crazymonkey05 said:
Sounds like you didn't wipe data
So go into cwm and wipe cache,data,delvick and try rebooting then
sent from my Sony Ericsson Xperia Play™(r800x) Running Slimbean 3.0 using Tapatalk 2™
Click to expand...
Click to collapse
These are the steps I did
1.- Flash the 4.0.2.A.0.58 Enhanced (2.3.4 firmware)
2.- Flash the LuPuSv8 JB Kernel via flashtools
3.- Take out the SDcard (I can't access to kernel menu without taking it out)
4.- Access Kernel menu then go into recovery mode
5.- Wipe data/cache/davlik
6.- Flash p.a.c.man jb
7.- Reboot
And then it bootloops and stays like that (i left it alone and it stayed like that for about 20 or 30 minutes)
I also wiped data/cache and davlik after flashing the rom, but got the same results, maybe I need a vendor unlocked firmware like in Turbo Kernel? I will try that...
Edit: Flashed the vendor unlocked firmware then wiped cache and data then installed the PACman rom but got bootloop again, maybe I should try with another kernel...
xkeita said:
These are the steps I did
1.- Flash the 4.0.2.A.0.58 Enhanced (2.3.4 firmware)
2.- Flash the LuPuSv8 JB Kernel via flashtools
3.- Take out the SDcard (I can't access to kernel menu without taking it out)
4.- Access Kernel menu then go into recovery mode
5.- Wipe data/cache/davlik
6.- Flash p.a.c.man jb
7.- Reboot
And then it bootloops and stays like that (i left it alone and it stayed like that for about 20 or 30 minutes)
I also wiped data/cache and davlik after flashing the rom, but got the same results, maybe I need a vendor unlocked firmware like in Turbo Kernel? I will try that...
Edit: Flashed the vendor unlocked firmware then wiped cache and data then installed the PACman rom but got bootloop again, maybe I should try with another kernel...
Click to expand...
Click to collapse
Do as above but after step 5 you need to go to mounts & storage and format Data/Cache & System (IMPORTANT DO NOT FORMAT ANYTHING ELSE):good:
Then flash p.a.c.man JB
tallman43 said:
Do as above but after step 5 you need to go to mounts & storage and format Data/Cache & System (IMPORTANT DO NOT FORMAT ANYTHING ELSE):good:
Then flash p.a.c.man JB
Click to expand...
Click to collapse
I did what you said but it keeps bootlooping @[email protected]
Why don't u use turbo kernel and start the process again...and no is not normal to take out your memory card to enter boot menu
Sent from my R800i using xda app-developers app
Yep, flashed turbo kernel v3.1 and it worked! Damn that lupus kernel made me waste many precious time...
xkeita said:
Yep, flashed turbo kernel v3.1 and it worked! Damn that lupus kernel made me waste many precious time...
Click to expand...
Click to collapse
Cool:good:
xkeita said:
Yep, flashed turbo kernel v3.1 and it worked! Damn that lupus kernel made me waste many precious time...
Click to expand...
Click to collapse
flashing that ftf was ur problem. U needed to flash the ftf with unlocked partitions. Same thing you shpoud of also needed to do for turbo kernel then format system and data partitions in either CWM or via fastboot, then flash kernel.
Sent from my GT-I9300 On Official JB
@tallman43 thx for the help bro (Y)
wedgess said:
flashing that ftf was ur problem. U needed to flash the ftf with unlocked partitions. Same thing you shpoud of also needed to do for turbo kernel then format system and data partitions in either CWM or via fastboot, then flash kernel.
Click to expand...
Click to collapse
I flashed the FTF with unlocked partitions played with the phone for about 30 secs, then flashed kernel, went to kernel menu then formated system, data, cache and davlik via CWM then flashed the rom, but that ended in bootloop, did the same with turbo kernel and it worked.
easy fix dont use Pac Rom its junk
xkeita said:
Hello again guys, I installed LuPuS v8 JB Kernel on my phone (I had 4.0.2.A.0.58 Enhanced Firmware (Gingerbread) installed) then I went to CWM to flash the .zip with the wifi modules and G.Apps but when I rebooted I got a bootloop. what I have to do to correctly install it? Please guide me since I'm kinda newbie to this of unlocked bootloaders and kernels :/ (I'm trying to install PACman rom and followed the FAQ guide but...)
EDIT: Forgot to add, my PLAY is an r800a(i) GSM btw, I have to take off the SDcard to enter to the Kernel menu, idk if this is normal
Click to expand...
Click to collapse
use slimbean !takes less room use it with lupus kerenel jb 480 rom.
---------- Post added at 02:49 PM ---------- Previous post was at 02:00 PM ----------
Just want to tell you that your kernels are by far the best. But the PAC man rom and the Paranoid hmm Dont work I cant get them to ever boot on my R800x CDMA
Keep up the hard work.
Hi, I've been having some problems with my Xperia Play getting stuck in a boot loop after flashing anything, or restoring a backup in CWM. This includes mods, like Adrenoboost, and the NXT Lockscreen, to themes. I have the Xperia Play R800x with an unlocked bootloader (via unlock code from Sony) and I'm using stock 2.3.3 Gingerbread, with the stock Kernel. I boot CWM by hotBooting LuPuS with Fastboot. I'm not really sure what to do because I really want to install these mods, and because restoring my nandroid backups also gets it stuck in a bootloop, I have to reflash the stock .ftf with FlashTool and reroot it every time.
x2110311x said:
Hi, I've been having some problems with my Xperia Play getting stuck in a boot loop after flashing anything, or restoring a backup in CWM. This includes mods, like Adrenoboost, and the NXT Lockscreen, to themes. I have the Xperia Play R800x with an unlocked bootloader (via unlock code from Sony) and I'm using stock 2.3.3 Gingerbread, with the stock Kernel. I boot CWM by hotBooting LuPuS with Fastboot. I'm not really sure what to do because I really want to install these mods, and because restoring my nandroid backups also gets it stuck in a bootloop, I have to reflash the stock .ftf with FlashTool and reroot it every time.
Click to expand...
Click to collapse
Hi. Not all mods are 100% compatible with stock ROM so you should use a custom one. Many custom ROMs are better than the stock one.
WhiteWashed said:
Hi. Not all mods are 100% compatible with stock ROM so you should use a custom one. Many custom ROMs are better than the stock one.
Click to expand...
Click to collapse
My only problem is, when I flash other ROMs they don't work, unless I also flash a custom Kernel. Anytime I flash a custom kernel, WiFi never connects, even if I flash the WiFi modules. It gets stuck at Obtaining IP Address, then stops.
x2110311x said:
My only problem is, when I flash other ROMs they don't work, unless I also flash a custom Kernel. Anytime I flash a custom kernel, WiFi never connects, even if I flash the WiFi modules. It gets stuck at Obtaining IP Address, then stops.
Click to expand...
Click to collapse
There's are some Gingerbread based roms that work also with the stock kernel and won't give you any problem with wifi (personal experience).
Try the gbx_play v3-rebuild here: http://forum.xda-developers.com/showthread.php?t=1897634
Or the Gin2kitkat here: http://forum.xda-developers.com/showthread.php?t=1631144
Try to flash one of these and let us know
Remember that before you flash a ROM you MUST make a wipe data/factory reset, wipe cache and wipe Dalvik Cache (in advanced options).
WhiteWashed said:
There's are some Gingerbread based roms that work also with the stock kernel and won't give you any problem with wifi (personal experience).
Try the gbx_play v3-rebuild here: http://forum.xda-developers.com/showthread.php?t=1897634
Or the Gin2kitkat here: http://forum.xda-developers.com/showthread.php?t=1631144
Try to flash one of these and let us know
Remember that before you flash a ROM you MUST make a wipe data/factory reset, wipe cache and wipe Dalvik Cache (in advanced options).
Click to expand...
Click to collapse
I do wipe the data and cache. I know how to install ROMs, I've done it with TWRP on my Kindle Fire, but I get stuck in a boot loop every time. I'll try these ROMs and see how they go.
WhiteWashed said:
There's are some Gingerbread based roms that work also with the stock kernel and won't give you any problem with wifi (personal experience).
Try the gbx_play v3-rebuild here: http://forum.xda-developers.com/showthread.php?t=1897634
Or the Gin2kitkat here: http://forum.xda-developers.com/showthread.php?t=1631144
Try to flash one of these and let us know
Remember that before you flash a ROM you MUST make a wipe data/factory reset, wipe cache and wipe Dalvik Cache (in advanced options).
Click to expand...
Click to collapse
I did a Factory Reset on CWM, then flashed Gin2KitKat, and wiped the cache and dalvik cache and it's stuck on the Android boot animation. It's been sitting there for like 10 minutes or so now. Flashtool does recognize it though.
Connected Device: R800
Installed version of busybox: BusyBox x1.21.1-Stericson (2013-09-26 14:33:26 BST) multi-call binary
Android Version: 2.3.7 / kernel version 2.6.32.9-perf / Build number: 4.0.2.A.0.79
Click to expand...
Click to collapse
It worked fine as soon as I hotBooted it with LuPus. I'm gonna try installing the other ROM I wanted and hotBooting LuPus
Strange, I have the opposite problem: lupus doesn't boot any ROM for me, excepting ICs ones.
In fact, to install a GB ROM I always have to flash first the stock rom and fw, and then flash the ROM with a custom recovery. Anyway by "hot booting" you mean custom recovery right?
Sent from my R800i using xda app-developers app
No, what I'm doing is using Fastboot to boot the phone with the kernel, without flashing it, to test it out. As soon as you shut the phone off, and turn it back on, it boots with whatever kernel is flashed on it
Sent from my R800x using xda app-developers app
x2110311x said:
No, what I'm doing is using Fastboot to boot the phone with the kernel, without flashing it, to test it out. As soon as you shut the phone off, and turn it back on, it boots with whatever kernel is flashed on it
Sent from my R800x using xda app-developers app
Click to expand...
Click to collapse
That's what I mean with custom recovery :laugh: (don't confuse with custom kernel).
When I had stock kernel I would boot LuPuS just for CWM, but I'll hotboot kernels to see how well they run
Sent from my R800x using xda-developers app
x2110311x said:
When I had stock kernel I would boot LuPuS just for CWM, but I'll hotboot kernels to see how well they run
Sent from my R800x using xda-developers app
Click to expand...
Click to collapse
So here's what you need to do, since you want stock and and fastbootalot for recoveries y don't you download xperia play clockwork mod app? It's version 4 or something like that don't use xparts it don't work with our Verizon plays since you have root this will install recovery for you to flash Roms mods etc
I'll edit later with a link to the thread that has the clockwork mod app install that MAKE A NANDROID before you flash anything it helps worse case you hotboot lupus to restore your nandroid you have then reboot and guess what stock 2.3.3 Rom and kernel
Sent from my ADR6300 using xda app-developers app
No I got everything to work fine. I have LuPuS flashed on, and I'm using the xElite Gamer ROM with no problem.
Sent from my R800x using xda-developers app