Related
Hello everyone,
First of all I would like to thank all of you in the community for being so engaged and eager to help out when something turns out in another direction as expected. Without your help so many would be left in complete darkness.
Let's start with my conclusion first:
I need either a BIN file for my phone which can be installed using LGNPST, or
A ROM file which can be installed using TWRP from TeenyBin recovery without verification errors on zip or phone assertion, or
A third – and to me unknown – solution which brings me closer to an unbricked phone.
Phone facts:
LG-E975, S/N: 303KPUU181542
TWRP 2.5.0.0 installed together with LGNPST TeenyBin
From the fastboot screen
PRODUCT NAME mako
VARIANT mako 32GB
HW VERSION rev_11 (&¤)
BOOTLOADER VERSION MAKOZ10f
BASEBAND VERSION N/A
CARRIER INFO None
SERIAL NUMBER xxxxx
SIGNING production
SECURE BOOT Enabled
LOCK STATE UNLOCKED
LG KDZ file identified is: E97510D_00
Sequence of things so far
1) As all my previous Android phones I use CWM for backup and testing new ROM’s I installed this on my Optimus G and rooted the device. Also upgraded CWM recovery to latest version, (not touch though)
2) After that it was not possible to boot into recovery due to ‘some’ error – I therefore changed recovery to built-in TWRP. Boot to recovery now gave Secure Boot Error – certification
NOTE: I found somewhere that rooting is NOT enough you also have to unlock, (FreeGee?). Could someone please confirm or reject?
3) Now I turned to “[REPAIR] TeenyBin - Softbrick Quick Fix / Bootloader Unlock [E971, E973, E975, F180*]” using LGNPST and TeenyBin. Finally something happened – I could access the TWRP built in.
4) Then I used ADB to push ROM to the internal SDCARD and recovery to install. But this method failed – tried several ROMs which all gave errors initially. I discovered that the install script pointed at “e975” in(ro.product.device and ro.build.product but the phone reports “geehrc4g”
This is the output in recovery.log when trying to flash ROM
Warning: No file_contexts
script aborted: assert failed: getprop("ro.product.device") == "e975" || getprop("ro.build.product") == "e975"
assert failed: getprop("ro.product.device") == "e975" || getprop("ro.build.product") == "e975"
Following the advice of changing the script by
a. Deleting the ‘assert’ line in the script, or
b. Changing the element to what the phone reports did not help
NOTE: I have seen someone claim that you should do this without unzipping first. I cannot see how this can be done. Please confirm if you have any knowledge on this. If unzip and zip causes the problem below – then what is the solution?
Changing the product device and build leads to this in recovery.log
E:Zip signature verification failed: 1
Error flashing zip '/sdcard/thinkingbridge.zip'
Updating partition details...
To ensure working environment I tried to flash gapps which worked perfectly so connection and recovery must be functional.
5) Now turning to: ”[GUIDE] How to UNBRICK your Optimus G - security error, bootloop etc”
I used the method described and downloaded the appropriate KDZ file etc. etc but flashing gives this log:
10:05:58 : Launching SW update
10:05:58 : Unpacking KDZ
10:06:05 : KDZ file extracted
10:06:13 : Files were extracted.
10:06:13 : LGMobileDL Load.
10:06:13 : Port = -1
10:06:13 : Connecting to phone
10:06:25 : Check Phone mode = 2
10:06:25 : Phone type check.......
10:06:26 : LGMobileDL.DLL Loading....
10:06:26 : _SetAuthMark Fail
10:06:26 : _SetAuthMark Ok : wAuthMark(65535)
10:06:26 : _DetachDLL Call
10:06:26 : _DetachDLL Call End
10:06:26 : ParamPhone\E97510
10:06:26 : Param : waitTime = 0
10:06:26 : Param : UsbHighSpeed = 1
10:06:26 : Param : PhoneMode = 2
10:06:26 : Param : BinVersion = E97510D_00
10:06:26 : Param : AuthMark = 65535
10:06:26 : Call fn_StartUpgrade
10:09:27 : 3GQCT : wParam = 100, lParam = 210
10:09:27 : Step : Upgrade Error error code = 210
10:09:27 : ResetStartInfo() Call
10:09:27 : _DetachDLL Call
10:09:27 : _DetachDLL Call End
10:09:27 : FreeLibrary Call
10:09:27 : FreeLibrary Call End
10:09:27 : ResetStartInfo() Call End
10:09:29 : ===FINISHED===
At the point where KDZ file is extracted the phone reverts from download mode to recovery which is probably why it fails.
Looking in the forums these problems are rather common and the suggestions are multiple. I hope to be able to get this problem solved with the help from the community and if possible condense whatever the experience and conclusions must be in a guide to help others in this situation. Thanks very much in advance.
Better use KDZ updater for files smaller than 1gb.for bigger files use flashtool.
Also,have you tried emergency recovery from lg mobile tool?since you are on stock,it should work.
kimitza said:
Better use KDZ updater for files smaller than 1gb.for bigger files use flashtool.
Also,have you tried emergency recovery from lg mobile tool?since you are on stock,it should work.
Click to expand...
Click to collapse
Hi Kimitza,
Thanks for your reply. I did discover the 1GB issue during my quest. Unfortunately I havn't found any smaller images in the KDZ format. Also afraid of getting an image incompatible which could end up finalizing the bricking of my phone
Regarding the stock thing I did try restoring using the LG Mobile Tool - but that also ended in an error where the tool asked me to disconnect the usb cable, restart the device and reconnect after the analysis. But I am unable to boot beyond fastboot and recovery.
I have a hunch that the TeenyBin could be the key to my issues. If - which I don't know - it has put "wrong" identity, (ro.product.device and ro.build.product), into "a" system file then changing this could be the way forward to use the recovery tool.
Do you think this is possible? And if do you know where the system keeps this information?
Cheers Klavs
it's in build.prop i think.
if your files are bigger,use flashtool.
https://xq55.app.box.com/s/89wvuj27cfd6jahqojoe
Hi there,
I'm stuck currently on exactly the same problem.
Actually i had my LGOG perfectly working with some CM10.1 Nightly build and yesterday i upgraded to CM10.2 Nightly (i also had to remove the first line of install script of the *.zip file, but this worked for me perfectly well in the past).
The upgrade process itself also worked fine, but when i rebooted my device the first time today, it got stuck on the CM boot screen animation.
Also Flashing the kdz file produced for me the same output (also with flashtool).
Finally i flashed another TeenyBin (the file is named "LS970_Original_TeenyBin-AA.bin" - i downloaded it the first time i unlocked my phone and I actually can't tell you where it is from) and after that flashing the kdz File worked for me (or at least, now it is installing).
Hope this helps you!
Edit:
My phone is working again (on CM10.1.3-RC2).
My Steps:
1. flash "E971.E973.E975.F180_Original_TeenyBin-AA.bin" via LGNPST
2. Boot to recovery
3. Download the zip file of the rom
4. Remove the first line of the "updater-script"
5. push the zip via adb to /sdcard
6. install the zip via recovery
7. it worked
Flashing the kdz file ended in a stuck boot-logo...
Good luck
What's the command to push the zip to the device. I'm getting lost reading all the info online.
Sent from my SGH-I317M using Tapatalk 4
nelly_85 said:
What's the command to push the zip to the device. I'm getting lost reading all the info online.
Sent from my SGH-I317M using Tapatalk 4
Click to expand...
Click to collapse
adb push xxx.zip /sdcard/
adb devices should show you device otherwise see if adb is setup correctly.
klavslund said:
Hello everyone,
First of all I would like to thank all of you in the community for being so engaged and eager to help out when something turns out in another direction as expected. Without your help so many would be left in complete darkness.
Let's start with my conclusion first:
I need either a BIN file for my phone which can be installed using LGNPST, or
A ROM file which can be installed using TWRP from TeenyBin recovery without verification errors on zip or phone assertion, or
A third – and to me unknown – solution which brings me closer to an unbricked phone.
Phone facts:
LG-E975, S/N: 303KPUU181542
TWRP 2.5.0.0 installed together with LGNPST TeenyBin
From the fastboot screen
PRODUCT NAME mako
VARIANT mako 32GB
HW VERSION rev_11 (&¤)
BOOTLOADER VERSION MAKOZ10f
BASEBAND VERSION N/A
CARRIER INFO None
SERIAL NUMBER xxxxx
SIGNING production
SECURE BOOT Enabled
LOCK STATE UNLOCKED
LG KDZ file identified is: E97510D_00
Sequence of things so far
1) As all my previous Android phones I use CWM for backup and testing new ROM’s I installed this on my Optimus G and rooted the device. Also upgraded CWM recovery to latest version, (not touch though)
2) After that it was not possible to boot into recovery due to ‘some’ error – I therefore changed recovery to built-in TWRP. Boot to recovery now gave Secure Boot Error – certification
NOTE: I found somewhere that rooting is NOT enough you also have to unlock, (FreeGee?). Could someone please confirm or reject?
3) Now I turned to “[REPAIR] TeenyBin - Softbrick Quick Fix / Bootloader Unlock [E971, E973, E975, F180*]” using LGNPST and TeenyBin. Finally something happened – I could access the TWRP built in.
4) Then I used ADB to push ROM to the internal SDCARD and recovery to install. But this method failed – tried several ROMs which all gave errors initially. I discovered that the install script pointed at “e975” in(ro.product.device and ro.build.product but the phone reports “geehrc4g”
This is the output in recovery.log when trying to flash ROM
Warning: No file_contexts
script aborted: assert failed: getprop("ro.product.device") == "e975" || getprop("ro.build.product") == "e975"
assert failed: getprop("ro.product.device") == "e975" || getprop("ro.build.product") == "e975"
Following the advice of changing the script by
a. Deleting the ‘assert’ line in the script, or
b. Changing the element to what the phone reports did not help
NOTE: I have seen someone claim that you should do this without unzipping first. I cannot see how this can be done. Please confirm if you have any knowledge on this. If unzip and zip causes the problem below – then what is the solution?
Changing the product device and build leads to this in recovery.log
E:Zip signature verification failed: 1
Error flashing zip '/sdcard/thinkingbridge.zip'
Updating partition details...
To ensure working environment I tried to flash gapps which worked perfectly so connection and recovery must be functional.
5) Now turning to: ”[GUIDE] How to UNBRICK your Optimus G - security error, bootloop etc”
I used the method described and downloaded the appropriate KDZ file etc. etc but flashing gives this log:
10:05:58 : Launching SW update
10:05:58 : Unpacking KDZ
10:06:05 : KDZ file extracted
10:06:13 : Files were extracted.
10:06:13 : LGMobileDL Load.
10:06:13 : Port = -1
10:06:13 : Connecting to phone
10:06:25 : Check Phone mode = 2
10:06:25 : Phone type check.......
10:06:26 : LGMobileDL.DLL Loading....
10:06:26 : _SetAuthMark Fail
10:06:26 : _SetAuthMark Ok : wAuthMark(65535)
10:06:26 : _DetachDLL Call
10:06:26 : _DetachDLL Call End
10:06:26 : ParamPhone\E97510
10:06:26 : Param : waitTime = 0
10:06:26 : Param : UsbHighSpeed = 1
10:06:26 : Param : PhoneMode = 2
10:06:26 : Param : BinVersion = E97510D_00
10:06:26 : Param : AuthMark = 65535
10:06:26 : Call fn_StartUpgrade
10:09:27 : 3GQCT : wParam = 100, lParam = 210
10:09:27 : Step : Upgrade Error error code = 210
10:09:27 : ResetStartInfo() Call
10:09:27 : _DetachDLL Call
10:09:27 : _DetachDLL Call End
10:09:27 : FreeLibrary Call
10:09:27 : FreeLibrary Call End
10:09:27 : ResetStartInfo() Call End
10:09:29 : ===FINISHED===
At the point where KDZ file is extracted the phone reverts from download mode to recovery which is probably why it fails.
Looking in the forums these problems are rather common and the suggestions are multiple. I hope to be able to get this problem solved with the help from the community and if possible condense whatever the experience and conclusions must be in a guide to help others in this situation. Thanks very much in advance.
Click to expand...
Click to collapse
Can you kindly tell me how you ware able to start kdz upgrading process, because I am in TWRP (i.e. bootlocker unlocked + paranoid android rom + no service) and I cannot go into downloading mode :/ (in order to revert back to stock)
Soft-brick
Hello everyone,
I soft bricked my phone that resulted in bootloop
I can only go to download mode. fastboot mode and recovery mode not possible
I tried to unbrick using custom rom and kdz updater but i cannot download kdz stock rom as i am new user it comes access denied.
Please help me... I need indian version stock rom for lg optimus G e975
sirfrajput said:
Can you kindly tell me how you ware able to start kdz upgrading process, because I am in TWRP (i.e. bootlocker unlocked + paranoid android rom + no service) and I cannot go into downloading mode :/ (in order to revert back to stock)
Click to expand...
Click to collapse
I've had the exact same problem... and I also don't know how to access Download Mode manually.
I found a way to go around the situation... and it was by flashing a Stock ROM zip file (and already Rooted!!)
It is a LG Stock ROM turned into a flashable zip file, which you can install via Recovery like any Custom ROM. It is Indian firmware version E97510e-IND-XX, but it has english language.
You can find it here:
http://forum.xda-developers.com/showthread.php?t=2407489
Go into Recovery, and flash the Stock ROM zip file, and the Keyboard-fix immediately after (or you be flooded with Force-Closes after reboot), also don't forget to wipe Data, Cache and Dalvik before rebooting to System, or you will be stuck with a bootloop situation.
When you get to your new LG Stock ROM system, you can either stay with this ROM (which is rooted and deodexed!), or you can change it!!
You will now be able to select "LG Software" on the USB connection type, and from there update to a newer firmware version via LG Mobile Support Tool, or to a firmware version of your choosing via KDZ Updater or Flash Tools... Flash Tools being the best method to choose, because it will not have KDZ extraction failures/issues.
See the link bellow for LG E975 firmware KDZ files...
tabrezak said:
Hello everyone,
I soft bricked my phone that resulted in bootloop
I can only go to download mode. fastboot mode and recovery mode not possible
I tried to unbrick using custom rom and kdz updater but i cannot download kdz stock rom as i am new user it comes access denied.
Please help me... I need indian version stock rom for lg optimus G e975
Click to expand...
Click to collapse
You will find it here!!
http://lg-phone-firmware.com/index.php?id_mod=20
mitushorizon said:
I've had the exact same problem... and I also don't know how to access Download Mode manually.
I found a way to go around the situation... and it was by flashing a Stock ROM zip file (and already Rooted!!)
It is a LG Stock ROM turned into a flashable zip file, which you can install via Recovery like any Custom ROM. It is Indian firmware version E97510e-IND-XX, but it has english language.
You can find it here:
http://forum.xda-developers.com/showthread.php?t=2407489
Go into Recovery, and flash the Stock ROM zip file, and the Keyboard-fix immediately after (or you be flooded with Force-Closes after reboot), also don't forget to wipe Data, Cache and Dalvik before rebooting to System, or you will be stuck with a bootloop situation.
When you get to your new LG Stock ROM system, you can either stay with this ROM (which is rooted and deodexed!), or you can change it!!
You will now be able to select "LG Software" on the USB connection type, and from there update to a newer firmware version via LG Mobile Support Tool, or to a firmware version of your choosing via KDZ Updater or Flash Tools... Flash Tools being the best method to choose, because it will not have KDZ extraction failures/issues.
See the link bellow for LG E975 firmware KDZ files...
You will find it here!!
http://lg-phone-firmware.com/index.php?id_mod=20
Click to expand...
Click to collapse
Dear it is simple to go in download mode manually, at the fast boot screen do the following...
Connect mobile to pc
Select power off and as soon as your mobile screen go black
Quickly press both volume buttons+power button and pull the cable out, and connect again (while all buttons are pressed).... And voila! You are in download mode
PS. You need to put your phone in download mode if while flashing kdz your mobile gets restarted....
mitushorizon said:
I've had the exact same problem... and I also don't know how to access Download Mode manually.
I found a way to go around the situation... and it was by flashing a Stock ROM zip file (and already Rooted!!)
It is a LG Stock ROM turned into a flashable zip file, which you can install via Recovery like any Custom ROM. It is Indian firmware version E97510e-IND-XX, but it has english language.
You can find it here:
http://forum.xda-developers.com/showthread.php?t=2407489
Go into Recovery, and flash the Stock ROM zip file, and the Keyboard-fix immediately after (or you be flooded with Force-Closes after reboot), also don't forget to wipe Data, Cache and Dalvik before rebooting to System, or you will be stuck with a bootloop situation.
When you get to your new LG Stock ROM system, you can either stay with this ROM (which is rooted and deodexed!), or you can change it!!
You will now be able to select "LG Software" on the USB connection type, and from there update to a newer firmware version via LG Mobile Support Tool, or to a firmware version of your choosing via KDZ Updater or Flash Tools... Flash Tools being the best method to choose, because it will not have KDZ extraction failures/issues.
See the link bellow for LG E975 firmware KDZ files...
You will find it here!!
http://lg-phone-firmware.com/index.php?id_mod=20
Click to expand...
Click to collapse
"i hit already thanx button dude" many thax you save my lovely G the only way for me to go back to stock because neither my phone goes to download mode before now i'm in stock greek rom thanx to you :good: must be in question and support section this threat
sirfrajput said:
Dear it is simple to go in download mode manually, at the fast boot screen do the following...
Connect mobile to pc
Select power off and as soon as your mobile screen go black
Quickly press both volume buttons+power button and pull the cable out, and connect again (while all buttons are pressed).... And voila! You are in download mode
PS. You need to put your phone in download mode if while flashing kdz your mobile gets restarted....
Click to expand...
Click to collapse
But my phone wouldn't enter in download mode with any key combination, thus my problem and thus my solution!
mitushorizon said:
But my phone wouldn't enter in download mode with any key combination, thus my problem and thus my solution!
Click to expand...
Click to collapse
You have to press both both volume buttons after selecting the power off....
I dont know... my phone always go in download mode this way
mitushorizon said:
I've had the exact same problem... and I also don't know how to access Download Mode manually.
I found a way to go around the situation... and it was by flashing a Stock ROM zip file (and already Rooted!!)
It is a LG Stock ROM turned into a flashable zip file, which you can install via Recovery like any Custom ROM. It is Indian firmware version E97510e-IND-XX, but it has english language.
You can find it here:
http://forum.xda-developers.com/showthread.php?t=2407489
Go into Recovery, and flash the Stock ROM zip file, and the Keyboard-fix immediately after (or you be flooded with Force-Closes after reboot), also don't forget to wipe Data, Cache and Dalvik before rebooting to System, or you will be stuck with a bootloop situation.
When you get to your new LG Stock ROM system, you can either stay with this ROM (which is rooted and deodexed!), or you can change it!!
After this step my phone keeps giving me a kernel error,
You will now be able to select "LG Software" on the USB connection type, and from there update to a newer firmware version via LG Mobile Support Tool, or to a firmware version of your choosing via KDZ Updater or Flash Tools... Flash Tools being the best method to choose, because it will not have KDZ extraction failures/issues.
See the link bellow for LG E975 firmware KDZ files...
You will find it here!!
http://lg-phone-firmware.com/index.php?id_mod=20
Click to expand...
Click to collapse
I do those exact steps and my phone starts with LG logo and after a few seconds the phone is on, i'll get an kernel error,
DemiGod Crash Handler : Kernel Crash! :
Press key to choose Dload Mode/Reboot/Fastboot
1)Volume Up: Dload Mode.
2) Volume Down: Reboot.
3) Power: Fastboot.
If you choose Dload Mode,
Please do following action.
1)Dload Mode. Please connect USB
2) Get the ram dump image using QCT's Memory Debug App
3) Send em-mail to contact point or [email protected].
and crashes, my phone is a e975.
Can't enter download mode, only have the options" Start" " Restart Bootloader", "Recovery mode", and power off.
Can anyone help me??
Assuming that the flashing of the stock ROM zip file was successful, things should be working fine...
But If they are not...
1 - Try entering into your Custom Recovery, and wipe Data, Cache, Dalvik-cache and System. (but not the Boot partition)
- flash the ROM zip file again and flash the keyboard fix immediately after.
- Wipe Data, Cache and Dalvik-cache again (but not the System nor the Boot partitions).
- Reboot! You should be fine.
If not... If you get stuck at boot due to Kernel issues...
2 - then go into your Custom Recovery, and flash a new Kernel, a suitable Kernel for LG E975 with 4.1.2 Jelly bean.
- after that wipe Data, Cache and Dalvik-cache (but not System nor Boot).
- and Reboot!
mitushorizon said:
Assuming that the flashing of the stock ROM zip file was successful, things should be working fine...
But If they are not...
1 - Try entering into your Custom Recovery, and wipe Data, Cache, Dalvik-cache and System. (but not the Boot partition)
- flash the ROM zip file again and flash the keyboard fix immediately after.
- Wipe Data, Cache and Dalvik-cache again (but not the System nor the Boot partitions).
- Reboot! You should be fine.
If not... If you get stuck at boot due to Kernel issues...
2 - then go into your Custom Recovery, and flash a new Kernel, a suitable Kernel for LG E975 with 4.1.2 Jelly bean.
- after that wipe Data, Cache and Dalvik-cache (but not System nor Boot).
- and Reboot!
Click to expand...
Click to collapse
First of all thanks for reply so soon, i've instaled another kernel , and seems to be working, but i've no network signal. and still dont have way to enter download mode so i can go back to stock. any ideias how to get into download mode??
To enter Download Mode do the following :
- turn off your phone,
- press and hold both "volume down" and "volume up" buttons,
- while holding those buttons connect your phone to PC via USB. (phone should enter download mode)
But wait... haven't you flashed the Indian stock ROM?
Isn't it already working? If yes, then you are already on Stock 4.1.2! More precisely, the E97510e-IND-XX stock firmware. Confirm this!
This means, you are on stock firmware but with Custom Recovery and Custom Bootloader!
Now, you don't need "Download Mode"!
If you want to update the firmware of your LG E975, or if you also want to get back to stock Recovery and stock Bootloader, then...
- install E975 up-to-date drivers and "LG Mobile Support Tool" on your computer, and reboot.
- on your phone go to Settings > Connection > PC Connection and choose the "LG Software" connection type,
- then connect your phone to computer via USB.
- and run LG Mobile Support Tool to update!
mitushorizon said:
To enter Download Mode do the following :
- turn off your phone,
- press and hold both "volume down" and "volume up" buttons,
- while holding those buttons connect your phone to PC via USB. (phone should enter download mode)
But wait... haven't you flashed the Indian stock ROM?
Isn't it already working? If yes, then you are already on Stock 4.1.2! More precisely, the E97510e-IND-XX stock firmware. Confirm this!
This means, you are on stock firmware but with Custom Recovery and Custom Bootloader!
Now, you don't need "Download Mode"!
If you want to update the firmware of your LG E975, or if you also want to get back to stock Recovery and stock Bootloader, then...
- install E975 up-to-date drivers and "LG Mobile Support Tool" on your computer, and reboot.
- on your phone go to Settings > Connection > PC Connection and choose the "LG Software" connection type,
- then connect your phone to computer via USB.
- and run LG Mobile Support Tool to update!
Click to expand...
Click to collapse
Your right i'm with stock firmware but with a custom recovery and bootloader.
Follow all your instructions to use LG Mobile Support Tool, but when it goes to install update it says that the pnone is not connected ??!!??
Restarted the phone and pc same thing happened again.
This started after i tried to unbrick my phone using teenybin, since that time teenybin changed my recovery and bootloader, and i dont' know how to put stock recovery and bootloader if i can't go to download mode.
Thanks
Ok, but the bootloader is only there to boot the device either to Recovery or to Android, if you can get to Android operating system then the bootloader doesn't matter anymore. (at least until you reboot.)
Answer the following:
Do you have a Firewall or Anti-vírus or anti-"something" software that may be blocking the connection between your phone and the PC?
Have you installed the latest drivers for LG E975 from LG site?
When you connect your phone to the PC, is the phone properly recognized by the PC?
If you turn on "USB Debugging" on your phone can you get ADB connection?
Did your phone had "LG Software" option selected when you connected it to the LG Mobile Support Tool?
Did you use the original USB cable of your phone?
If the problem with the connection is related to the LG E975 drivers, you may want to try this...
- run LG Mobile Support Tool (without connecting your phone) and on the left you have an option to manual select and install the drivers of your phone.
- after that search your PC for a folder named "LGMOBILEAX" and erase it.
- reboot your PC.
- run LG Mobile Support Tool again and connect your phone (in "LG Software" mode) to PC and select the option to recover the phone, "Update Recovery".
If the problem with the connection is not related to the drivers, try this...
- Go to Google Play and install the "FreeGee" app on your phone.
- and run the app. (make sure you have Root and Busybox properly working before running FreeGee)
- on FreeGee select either CWM or TWRP. (but I recommend TWRP.)
{If all goes well, this will install the CWM / TWRP custom recovery and a proper bootloader to your phone (much more complete then TeenyBin bootloader.)}
- when FreeGee is done, turn off your phone.
- now try to enter into Download Mode...
To enter Download Mode do the following :
- turn off your phone, (if is not already)
- press and hold both "volume down" and "volume up" buttons,
- while holding those 2 buttons connect your phone to PC via USB. (please use the original USB cable)
Try at least 2 or 3 times to enter into Download Mode, since the procedure is tricky... It only takes one button not being pressed properly for the procedure to fail.
Please help me I can't reflash .kdz after KitKat rom. I installed Freegee app and chose latest cwm recovery. Now every time I try the LG flash tool stops in the beginning of flashing. Battery is full. I even wiped system and data in cwm but no go.. I can't get rid of KitKat. It still boots to that.
I now how but i speek french
"Envoyé depuis mon LG-E986 avec Tapatalk"
that's what I get in the flash tool.
10:08:24 : wParam : 100, lParam = 0
10:08:24 : MODEL DLL Event : (100, 0)
10:08:24 : Step : TYPE_WPARAM_UPGRADE_ERROR
10:08:24 : CleanModelDll() : Free Model.dll
10:08:24 : _DetachDLL Call
10:08:29 : _DetachDLL Call End
10:08:29 : wParam : 100, lParam = 64
10:08:29 : MODEL DLL Event : (100, 64)
10:08:29 : Step : TYPE_WPARAM_UPGRADE_ERROR
10:08:29 : CleanModelDll() : Free Model.dll
10:08:29 : _DetachDLL Call
10:08:34 : _DetachDLL Call End
10:08:34 : Page_Error şÎşĐŔÔ´Ď´Ů
10:08:34 : ż©±â´Â Retry şÎşĐŔÔ´Ď´Ů
10:08:34 : Page_Error şÎşĐŔÔ´Ď´Ů
10:08:34 : ż©±â´Â Retry şÎşĐŔÔ´Ď´Ů
this is the famous low battery issue . dont use freegee anymore and try to flash on emergency mode instead DIAG
pallcsa said:
Please help me I can't reflash .kdz after KitKat rom. I installed Freegee app and chose latest cwm recovery. Now every time I try the LG flash tool stops in the beginning of flashing. Battery is full. I even wiped system and data in cwm but no go.. I can't get rid of KitKat. It still boots to that.
Click to expand...
Click to collapse
Did you try to restore a nandroid backup instead of a custom rom. Users/developers (i.e anirudhk)have uploaded theirs to xda`s storagecow. One needs to put it in the right folder, so that the recovery system recognizes them.
i had this problem 2 times and i could flash only without low battery issue on emergency mode instead DIAG. But this never worked at the 1. try. I had to try it realy often times and randomly it works, but only on emergency
since then i wont try customs roms anymore untill freegee is fixed. People say its fixed, but 4 me it seems it isnt
lg-user45 said:
i had this problem 2 times and i could flash only without low battery issue on emergency mode instead DIAG. But this never worked at the 1. try. I had to try it realy often times and randomly it works, but only on emergency
since then i wont try customs roms anymore untill freegee is fixed. People say its fixed, but 4 me it seems it isnt
Click to expand...
Click to collapse
Thanks for the tip. I tried it in emergency mode too but same thing happened. I am starting to feel a bit nervous.
xifizurk said:
Did you try to restore a nandroid backup instead of a custom rom. Users/developers (i.e anirudhk)have uploaded theirs to xda`s storagecow. One need to put it in the right folder, so that the recovery system recognizes them.
Click to expand...
Click to collapse
I was trying hard to look for those nandroid backups but I couldn`t find them anywhere. Could somebody point me to the right direction ? I need a nandroid backup really bad because I can`t flash original firmware at all. :crying:
pallcsa said:
I was trying hard to look for those nandroid backups but I couldn`t find them anywhere. Could somebody point me to the right direction ? I need a nandroid backup really bad because I can`t flash original firmware at all. :crying:
Click to expand...
Click to collapse
It's here :
http://storagecow.eu/Xda/Users/Anirudhks-OptimusGPro/Stock.rar
PROBLEM:
Subsystem Crash!
-----------------------------------------------------------------------------------------------------------------
DemiGod Crash Handler : Subsystem Crash! : External_modem (Undefined error)
Press key to choose Dload Mode/Reboot/Fastboot
1)Volume Up: Dload Mode.
2) Volume Down: Reboot.
3) Power: Fastboot.
If you choose Dload Mode,
Please do following action.
1)Dload Mode. Please connect USB
2) Get the ram dump image using QCT's Memory Debug App
3) Send em-mail to contact point or [email protected].
-------------------------------------------------------------------------------------------------------
When i flash my rom(s) the above problem arises after boot. Tried with pacman ,carbon and pa. All same problem.
Any solution guys?
Thanx
EDIT: When i remove my sim card, it boots normally
shirish893 said:
PROBLEM:
Subsystem Crash!
-----------------------------------------------------------------------------------------------------------------
DemiGod Crash Handler : Subsystem Crash! : External_modem (Undefined error)
Press key to choose Dload Mode/Reboot/Fastboot
1)Volume Up: Dload Mode.
2) Volume Down: Reboot.
3) Power: Fastboot.
If you choose Dload Mode,
Please do following action.
1)Dload Mode. Please connect USB
2) Get the ram dump image using QCT's Memory Debug App
3) Send em-mail to contact point or [email protected].
-------------------------------------------------------------------------------------------------------
When i flash my rom(s) the above problem arises after boot. Tried with pacman ,carbon and pa. All same problem.
Any solution guys?
Thanx
EDIT: When i remove my sim card, it boots normally
Click to expand...
Click to collapse
Hey,
They are two ways to fix this, first flash the modem in TWRP (Never tried this my self so not so sure it works or not) described the same problem in this thread study it if it help you [Guide]Restore to Stock "Bricked" "Unlocked" LG Optimus G f180,E97x
Second as I told you earlier go back to total stock try the KDZ updater for that if it gives error then flashing the tot file through LGNPST, you will be able to flash any desire stock KDZ after that via R&D Tool or use the first method to unlock the bootloader in above thread and then flash any custom rom you desire.
If you do go to original stock of your rom remember to backup the modem and EFS partition (if not already did, they contain your IMEI incase anything else go wrong) and copy them to safe place in computer or cloud.
hackenggr said:
Hey,
They are two ways to fix this, first flash the modem in TWRP (Never tried this my self so not so sure it works or not) described the same problem in this thread study it if it help you [Guide]Restore to Stock "Bricked" "Unlocked" LG Optimus G f180,E97x
Second as I told you earlier go back to total stock try the KDZ updater for that if it gives error then flashing the tot file through LGNPST, you will be able to flash any desire stock KDZ after that via R&D Tool or use the first method to unlock the bootloader in above thread and then flash any custom rom you desire.
If you do go to original stock of your rom remember to backup the modem and EFS partition (if not already did, they contain your IMEI incase anything else go wrong) and copy them to safe place in computer or cloud.
Click to expand...
Click to collapse
r and d tool saying that my battery level is low... but my batter is 100% charged... dunno what is happening... i am going to try tot file
shirish893 said:
PROBLEM:
Subsystem Crash!
-----------------------------------------------------------------------------------------------------------------
DemiGod Crash Handler : Subsystem Crash! : External_modem (Undefined error)
Press key to choose Dload Mode/Reboot/Fastboot
1)Volume Up: Dload Mode.
2) Volume Down: Reboot.
3) Power: Fastboot.
If you choose Dload Mode,
Please do following action.
1)Dload Mode. Please connect USB
2) Get the ram dump image using QCT's Memory Debug App
3) Send em-mail to contact point or [email protected].
-------------------------------------------------------------------------------------------------------
When i flash my rom(s) the above problem arises after boot. Tried with pacman ,carbon and pa. All same problem.
Any solution guys?
Thanx
EDIT: When i remove my sim card, it boots normally
Click to expand...
Click to collapse
My friend it is kernel isiue And some nexus 4 phones have it. İ go unlock my phone and i use it normaly 3 mounth And go another phone operator and i have ur isuee i cant use any custom ROM .but i go cwm recovery go back (restore my stock ROM un cwm) but i m not have any problem.i back to stock ROM for kdz methot And i m w8 İng KitKat .i go for big search and spend 20 h ....i have one methot .i m not test it but u cant test it and say me test results .d İF u want it say me i give link for u .d it is small kernel problem .d
Sent from my LG-E975 using XDA Free mobile app
metrixx02 said:
My friend it is kernel isiue And some nexus 4 phones have it. İ go unlock my phone and i use it normaly 3 mounth And go another phone operator and i have ur isuee i cant use any custom ROM .but i go cwm recovery go back (restore my stock ROM un cwm) but i m not have any problem.i back to stock ROM for kdz methot And i m w8 İng KitKat .i go for big search and spend 20 h ....i have one methot .i m not test it but u cant test it and say me test results .d İF u want it say me i give link for u .d it is small kernel problem .d
Sent from my LG-E975 using XDA Free mobile app
Click to expand...
Click to collapse
I got the solution.. I flashed modem.img by fastboot... And it worked
shirish893 said:
I got the solution.. I flashed modem.img by fastboot... And it worked
Click to expand...
Click to collapse
How modem.img where u found it?
Sent from my LG-E975 using XDA Free mobile app
THIS IS FOR THE D802 ONLY
This is a solution to the LG Flash Tool GUI getting stuck at 2% and giving an error while trying to flash a .KDZ that IS COMPATIBLE with your phone.
I haven't found this solution anywhere on the forums so thought I would share it.
Basically it re-installs your mmcblk partitions.
NOTE: First off, it's worth checking your LG Flash Tool error log to make sure your error is the following
(C:\LGMobileUpgrade\log0.txt)
Code:
04:30:34 : ********* CDMA Model.dll input Parameter End*************
04:30:37 : wParam : 20, lParam = 540
04:30:37 : MODEL DLL Event : (20, 540)
04:30:38 : Model File Count = 540
04:30:38 : wParam : 100, lParam = 51
[B]04:30:38 : MODEL DLL Event : (100, 51)[/B]
[B]04:30:38 : Step : TYPE_WPARAM_UPGRADE_ERROR[/B]
04:30:38 : CleanModelDll() : Free Model.dll
04:30:38 : _DetachDLL Call
04:30:43 : _DetachDLL Call End
04:30:45 : Page_Error ºÎºÐÀÔ´Ï´Ù
04:30:45 : ¿©±â´Â Retry ºÎºÐÀÔ´Ï´Ù
The above BOLD text is the common error when the LG Flash Tool is getting stuck at 2%.
Once you've confirmed you are getting the same error AND you are indeed getting stuck at 2%, please continue.
1. Download FixedDownloadCMode_droidth.zip.
2. If you do not already have the ADB driver installed, download and install it.
3. Make sure you have a custom recovery installed. Recommended LATEST version of TWRP for the D802 from HERE.
4. Boot into Recovery
5. Plug LG-D802 into Computer and wait for ADB connectivity.
6. Extract FixedDownloadCMode_droidth.zip and run FixedDownloadCMode.bat.
7. Wait for batch process to finish (It will push all bin and img files, then dd all the files).
8. Boot into Download Mode and your .KDZ should flash without LG Flash Tool getting stuck at 2%.
It' work for you. I so happy if it can help you.
somboons said:
It' work for you. I so happy if it can help you.
Click to expand...
Click to collapse
It did indeed help me .
Thanks for posting this, I was getting really frustrated at this error back when I needed to factory reset my phone for warranty. Ended up using the LG Mobile support Tool's Upgrade Recovery function instead.
Will give this a try next time I need to factory reset my phone :good:
have a look my solution :
http://forum.xda-developers.com/lg-...14-2-error-t3021533/post58650373#post58650373
condudad said:
Thanks for posting this, I was getting really frustrated at this error back when I needed to factory reset my phone for warranty. Ended up using the LG Mobile support Tool's Upgrade Recovery function instead.
Will give this a try next time I need to factory reset my phone :good:
Click to expand...
Click to collapse
Tell me about it, knowing your KDZ SHOULD be flashing and having it crash on you at 2% is the worst thing in the world .
hsahin4 said:
have a look my solution :
http://forum.xda-developers.com/lg-...14-2-error-t3021533/post58650373#post58650373
Click to expand...
Click to collapse
Yeah it's known that changing your ROM can sometimes change the integrity of your partitions. Thanks for sharing your solution.
d00lz said:
Tell me about it, knowing your KDZ SHOULD be flashing and having it crash on you at 2% is the worst thing in the world .
Yeah it's known that changing your ROM can sometimes change the integrity of your partitions. Thanks for sharing your solution.
Click to expand...
Click to collapse
By the way, I decided to use CloudyG2 rom instead of stock one due to latency during incoming calls.
I tried cloudystock but also it has same bug as it is based on stock.
I am really happy with CloudyG2; smooth, stable, bug free and amazing battery life. Almost 35 hrs with 4hrs screen time.
When I had that problem I just downloaded v10 tot files and flashed them it's much easier and it's works perfectly.Arfter flash flashed v20 via kdz and no stuck works like a charm maybe this info will help
For me dont work ... its hard brick my device.
for me what work ( i can enter into recovery)
Wipe system, data , dalvik, cache.
flash that rom. ( LG flash tool dont detect my device like Optimus lg g3 1.4.1 rom and download mode work without problem) http://forum.xda-developers.com/lg-g2/development-d802/d80220h-original-prerooted-stock-t3019155 FW with bootstack
After flash over http://forum.xda-developers.com/showthread.php?t=2432476 LG flash tool D80210A_00.kdz , becaus Kitkat firmware dont add u stock recovery ( way go into recovery. In Lg flash tool set:
Select Type : CDMA
Phone mode : cs_emergency
select: D80210A_00.kdz
CSE flash
and Start
Dont look at that error message simply press ok and w8 till ur phone boot up. U will have pure stock lg g2 with all drivers like when u buy phone.
The biggest problem of LG flash tool its detecting custom firmware like another FW and its disable download mode flash. Idk why. I try full wipe phone and its doesnt work, only flashinh stock over recovery.
Enjoy i hope my little guide work.
Vybramo said:
For me dont work ... its hard brick my device.
for me what work ( i can enter into recovery)
Wipe system, data , dalvik, cache.
flash that rom. ( LG flash tool dont detect my device like Optimus lg g3 1.4.1 rom and download mode work without problem) http://forum.xda-developers.com/lg-g2/development-d802/d80220h-original-prerooted-stock-t3019155 FW with bootstack
After flash over http://forum.xda-developers.com/showthread.php?t=2432476 LG flash tool D80210A_00.kdz , becaus Kitkat firmware dont add u stock recovery ( way go into recovery. In Lg flash tool set:
Select Type : CDMA
Phone mode : cs_emergency
select: D80210A_00.kdz
CSE flash
and Start
Dont look at that error message simply press ok and w8 till ur phone boot up. U will have pure stock lg g2 with all drivers like when u buy phone.
The biggest problem of LG flash tool its detecting custom firmware like another FW and its disable download mode flash. Idk why. I try full wipe phone and its doesnt work, only flashinh stock over recovery.
Enjoy i hope my little guide work.
Click to expand...
Click to collapse
This solution is for people experiencing the same error log mentioned in the original post.
However, thank you for sharing your solution for your specific case.
The miracle think its i have this error, thats why i post there my solution which work for me.
d00lz said:
1. Download FixedDownloadCMode_droidth.zip.
2. If you do not already have the ADB driver installed, download and install it.
3. Make sure you have a custom recovery installed. Recommended LATEST version of TWRP for the D802 from HERE.
4. Boot into Recovery
5. Plug LG-D802 into Computer and wait for ADB connectivity.
6. Extract FixedDownloadCMode_droidth.zip and run FixedDownloadCMode.bat.
7. Wait for batch process to finish (It will push all bin and img files, then dd all the files).
8. Boot into Download Mode and your .KDZ should flash without LG Flash Tool getting stuck at 2%.
Click to expand...
Click to collapse
Hello,
Now I returned back to stock Turkey ROM (4.4.2 V20C) and trying to install V20H Open Europe but some problem here.
And I decided to try the way that you explained above.
1. I had installled LG Universal Drivers. Does it includes ADB drivers also?
6. Run *.bat file but nothing happens. Do I need to enable something within TWRP environment?
Can you please guide me?
hello how eaxctly to use with adb to start the bat file?
hsahin4 said:
Hello,
Now I returned back to stock Turkey ROM (4.4.2 V20C) and trying to install V20H Open Europe but some problem here.
And I decided to try the way that you explained above.
1. I had installled LG Universal Drivers. Does it includes ADB drivers also?
6. Run *.bat file but nothing happens. Do I need to enable something within TWRP environment?
Can you please guide me?
Click to expand...
Click to collapse
1. Download and install ADB & Fastboot Drivers.
2. Restart your PC.
3. Enable USB Debugging in Developer Options.
4. Reboot your phone.
5. Boot your phone into TWRP and plug your phone into your PC.
6. Open cmd.exe by going Start -> Run -> "cmd.exe" -> OK.
7. Type adb devices, you should get an output like this,
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
8. If you see your device listed adb is working and you can continue.
9. Now exit cmd.exe and extract the FixedDownloadCMode_droidth.zip file.
10. Go into your newly created /FixedDownloadCMode_droidth/ folder and double-click FixedDownloadCMode.bat.
hyundai2010 said:
hello how eaxctly to use with adb to start the bat file?
Click to expand...
Click to collapse
You don't use adb to start the bat file, the bat file is run by double clicking on it with your cursor.
The bat file will take control of adb for you. Make sure your phone is connected via adb first (refer to the steps above).
thanks working awesome
Great! You're the man.. I've tried 5 hours without success till i found your fix *thumbsup*
Hows do I check for the errors on my flashtool?
ClarkOwen said:
Hows do I check for the errors on my flashtool?
Click to expand...
Click to collapse
Do you know how to navigate through your file system?
Your log file is located at C:\LGMobileUpgrade\ like I said in OP.
do I have to install trwp to be able to rom install? is this method not working for original recovery?
benveq said:
do I have to install trwp to be able to rom install?
Click to expand...
Click to collapse
Yes.
benveq said:
is this method not working for original recovery?
Click to expand...
Click to collapse
Original Recovery does not let you use ADB and has little to no features.
If you accidentally formatted your device , then how to restore imei
How to deal with: Download not complete error
Sn writer
Elaborate more with Download part
Download Not Complete: something blah blah blah after 10s, 0*92655 something something...
Sn writer / Maui Meta doesn't work for null imei for realme3.
Thanx
The device on which I am flashing the firmware is REALME 3, I used SP Flash tool for flashing, while flashing with SP Flash flash tool, the tool show EMMC unknown,but the flashing completes successfully,
then after pressing power ON, this message appears at the bottom ,
Download Not Complete! Please press Volume+ and power key for 10s to power off. Then download again. Otherwise will block here 60s until shutdown automatically. error code : 0*9925669( I can't see the last digit bcoz of the glass cover).
PLS GUIDE.THNX
Give possible solution for imei
@yas8say , has provided possible solution, I will try that next time I'll get this error. In thread brick repair by @ATDteam .
If you can use SP flash tools, SN writer DOES work on your fone, but it's figuring out a certain timing and sequence of events. that prove my point. Your at the point you need to be, it's waiting on you doing what I'm trying to say... your too demanding wanting the quick fix...
Everytime you post pauses me in case I need to change what I write to you, so slow down, your distracting me lol
Sn Writer is actually a pain to use, and there are many versions. But I learnt a sneaky fast path with it's appearing to not work. It does work, but kind of in reverse of what you think it does.
Sn Writer, strange but true, calls 'serial' as in serial number, 'barcode' in some versions, so some think because they cant see 'serial' that it wont work. I know because at first, I did. Took me a while to learn this.
Load up Sn Writer, it'll ask to load a file, the window that opens should be where you see MTK DA ALL IN bin, select it. Then choose scatterfile from stock firmware.
Now set correct attestation keys found in stock rom, your aftersales stock, with your attestation keys /google keys blah blah...
You then have to choose what you want to flash. If you see serial, that is NOT what you want to flash, you have to flash BARCODE! (your fones serial number) I know you said IMEI, but in order, SN writer flashes BARCODE before IMEI 1, so you MUST flash serial and mac PACKAGE given in stock rom?
So what I do is open the window to type in BARCODE box, my serial number.
Imei 1 is obvious, but you MUST do imei 2 as well, or it will add a few digits to imei 1's mac, put it in imei 2 that may not corespond to your attestation key.
Over to fone.
I turn my fone OFF, hit start in SNWriter, and plug phone into pc, and wait. You can tie your hands to your chair for a min, because if you interupt this TIMING...
Just when you think it wont work, folks give up. Wait that wee bit longer... it will show pass or fail. If its all genuine stock, it cant fail, only impatience caused by not knowing this sequence, and SN's bug-inesss
I'm too tired right now, and I see you posting again lol, my eyes are dry and its sleep time, and since you think it wont work, I'll catch up later today on this post, beacuse I'm gettin ratty with myself lol
Patience.. I'll be back...
Ank Sak said:
@yas8say , has provided possible solution, I will try that next time I'll get this error. In thread brick repair by @ATDteam[/USE
[/QUOTE]
Click to expand...
Click to collapse
HI
If you have successful in booting up your device try rooting it with magisk and find the .bin file in /data/nvram and edit it !
yas8say said:
HI
If you have successful in booting up your device try rooting it with magisk and find the .bin file in /data/nvram and edit it !
Click to expand...
Click to collapse
Ank Sak said:
Give possible solution for imei
Click to expand...
Click to collapse
I have faced this too, but luckily i had already taken a backup from recovery of nvram ,nvcfg, nvdata partitions .After flashing the recovery i just restored the partitions.
SO, GUYS IF YOU CAN BOOT INTO RECOVERY FIRST THING YOU HAVE TO DO BEFORE FLASHING ANY PARTITION IS TO MAKE A BACKUP OF THEM
yas8say said:
HI
If you have successful in booting up your device try rooting it with magisk and find the .bin file in /data/nvram and edit it !
Click to expand...
Click to collapse
The unique problem I am facing is that I was able to flash the firmware, but I couldn't do anything after that because I did format which resulted in """ null imei """ without it the in-depth test app doesn't work, so the after process of bootloader unlocking and then rooting is unachievable, I can't downgrade with official ozip file given in realme website, I did that and it resulted in hard brick( basically without unlocking bootloader I can't do sh*t) , my device is up & running but without imei the further processes are stalled, I will try the method of using sn writer mentioned here..the repair guy even mentioned something about bin fine not found so he couldn't write imei, I have successfully used Maui Meta & SN Writer to write imei of my other mediatek chip containing device , but it didn't worked on realme3, yes you may have solved my problem of "" Download not Complete"" I have posted two pictures in the brick repair thread by @ATDteam . Thanx.
I will try to repair imei and post the outcome here.
2 years ago I formatted by other mediatek chip device lenevo and it did show NVRam error in wifi, after repairing imei it didn't show , & now this mediatek chip device realme does show NVRam error in wifi :: -- NVRAM WARNING: Err =0*10
Ank Sak said:
The unique problem I am facing is that I was able to flash the firmware, but I couldn't do anything after that because I did format which resulted in """ null imei """ without it the in-depth test app doesn't work, so the after process of bootloader unlocking and then rooting is unachievable, I can't downgrade with official ozip file given in realme website, I did that and it resulted in hard brick( basically without unlocking bootloader I can't do sh*t) , my device is up & running but without imei the further processes are stalled, I will try the method of using sn writer mentioned here..the repair guy even mentioned something about bin fine not found so he couldn't write imei, I have successfully used Maui Meta & SN Writer to write imei of my other mediatek chip containing device , but it didn't worked on realme3, yes you may have solved my problem of "" Download not Complete"" I have posted two pictures in the brick repair thread by @ATDteam . Thanx.
I will try to repair imei and post the outcome here.
Click to expand...
Click to collapse
If you want to unlock bootloader just use mtkclient ,its very simple.
And if you want my imei files i can provide you but you got to have twrp installed.BTW where are you from?
Tried mtkclient & mtksu app , didn't work, first I will write imei, then use in-depth test, then unlock bootloader, then downgrade, then root using mtksu.. fingers crossed
Ank Sak said:
Tried mtkclient & mtksu app , didn't work, first I will write imei, then use in-depth test, then unlock bootloader, then downgrade, then root using mtksu.. fingers crossed
Click to expand...
Click to collapse
What error did you faced when using mtkclient?
yas8say said:
What error did you faced when using mtkclient?
Click to expand...
Click to collapse
I cannot boot in fastboot mode ( I forgot to tell , in realme )
Mtk client:: shows this...
Daxflash - uploading stage 1 from mtkallinone_ da_5.2136.bin
Preloader
Preloader- [lib] : ?[ 31mError on DA_send cmd?[0m
Daxflash
Daxflash- [lib] : ?[31mError on sending DA.?[0m
Main
Main - [lib] : ?[31mError uploading da?[0m
Device formats,
First time some error
Now I ran second time python mtk xflash seccfg unlock
And now bootloader is unlocked !!! Cheers
I don't want to brick and I want to root , what must I do , pls give in steps.. Thnx
Should I directly install twrp img then magisk zip??
Orange state
Device is unlocked blah blah blah( same as lenevo)
But no fastboot mode
When use adb reboot bootloader
This comes up
The serial is not match
Fastboot_unlock_verify fail
Should I try using in-depth test app??
Ank Sak said:
Should I directly install twrp img then magisk zip??
Orange state
Device is unlocked blah blah blah( same as lenevo)
But no fastboot mode
When use adb reboot bootloader
This comes up
The serial is not match
Fastboot_unlock_verify fail
Should I try using in-depth test app??
Click to expand...
Click to collapse
TRY this:
python mtk w recovery recovery_name.img
then boot into recovery.
yas8say said:
TRY this:
python mtk w recovery recovery_name.img
then boot into recovery.
Click to expand...
Click to collapse
My device is realme3, it's on Android10 c.17, will I will be able to root with magisk ? Ok I will try.
No straight business,
Ok i tried, gave same error preloader dax main. .., so I switched off , as soon as the device turns off n pressed all three buttons to go into brom mode, the other cmd with python command ran and wrote twrp Spartan recovery,, then switched on, key combo didn't work, bcoz it was showing ' the serial is not match......' so I typed adb reboot recovery, it booted to realme UI recovery.
Surely have to downgrade to Android 9 to root & install recovery